clean-up NAND / BBT code, flags

index a46e9bb..456fb34 100644
@@ -410,10 +410,11 @@ static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
 	else {
 		nand_get_device(chip, mtd, FL_WRITING);
 
-		/* Write to first two pages and to byte 1 and 6 if necessary.
-		 * If we write to more than one location, the first error
-		 * encountered quits the procedure. We write two bytes per
-		 * location, so we dont have to mess with 16 bit access.
+		/*
+		 * Write to first two pages if necessary. If we write to more
+		 * than one location, the first error encountered quits the
+		 * procedure. We write two bytes per location, so we dont have
+		 * to mess with 16 bit access.
 		 */
 		do {
 			chip->ops.len = chip->ops.ooblen = 2;

@@ -423,11 +424,6 @@ static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
 
 			ret = nand_do_write_oob(mtd, ofs, &chip->ops);
 
-			if (!ret && (chip->options & NAND_BBT_SCANBYTE1AND6)) {
-				chip->ops.ooboffs = NAND_SMALL_BADBLOCK_POS
-					& ~0x01;
-				ret = nand_do_write_oob(mtd, ofs, &chip->ops);
-			}
 			i++;
 			ofs += mtd->writesize;
 		} while (!ret && (chip->options & NAND_BBT_SCAN2NDPAGE) &&

@@ -3131,16 +3127,6 @@ ident_done:
 			 *maf_id == NAND_MFR_MICRON))
 		chip->options |= NAND_BBT_SCAN2NDPAGE;
 
-	/*
-	 * Numonyx/ST 2K pages, x8 bus use BOTH byte 1 and 6
-	 */
-	if (!(busw & NAND_BUSWIDTH_16) &&
-			*maf_id == NAND_MFR_STMICRO &&
-			mtd->writesize == 2048) {
-		chip->options |= NAND_BBT_SCANBYTE1AND6;
-		chip->badblockpos = 0;
-	}
-
 	/* Check for AND chips with 4 page planes */
 	if (chip->options & NAND_4PAGE_ARRAY)
 		chip->erase_cmd = multi_erase_cmd;

@@ -3538,11 +3524,6 @@ void nand_release(struct mtd_info *mtd)
 	kfree(chip->bbt);
 	if (!(chip->options & NAND_OWN_BUFFERS))
 		kfree(chip->buffers);
-
-	/* Free bad block descriptor memory */
-	if (chip->badblock_pattern && chip->badblock_pattern->options
-			& NAND_BBT_DYNAMICSTRUCT)
-		kfree(chip->badblock_pattern);
 }
 EXPORT_SYMBOL_GPL(nand_release);
 

index ccbeaa1..5ffb9a4 100644
@@ -114,28 +114,6 @@ static int check_pattern(uint8_t *buf, int len, int paglen, struct nand_bbt_desc
 			return -1;
 	}
 
-	/* Check both positions 1 and 6 for pattern? */
-	if (td->options & NAND_BBT_SCANBYTE1AND6) {
-		if (td->options & NAND_BBT_SCANEMPTY) {
-			p += td->len;
-			end += NAND_SMALL_BADBLOCK_POS - td->offs;
-			/* Check region between positions 1 and 6 */
-			for (i = 0; i < NAND_SMALL_BADBLOCK_POS - td->offs - td->len;
-					i++) {
-				if (*p++ != 0xff)
-					return -1;
-			}
-		}
-		else {
-			p += NAND_SMALL_BADBLOCK_POS - td->offs;
-		}
-		/* Compare the pattern */
-		for (i = 0; i < td->len; i++) {
-			if (p[i] != td->pattern[i])
-				return -1;
-		}
-	}
-
 	if (td->options & NAND_BBT_SCANEMPTY) {
 		p += td->len;
 		end += td->len;

@@ -167,13 +145,6 @@ static int check_short_pattern(uint8_t *buf, struct nand_bbt_descr *td)
 		if (p[td->offs + i] != td->pattern[i])
 			return -1;
 	}
-	/* Need to check location 1 AND 6? */
-	if (td->options & NAND_BBT_SCANBYTE1AND6) {
-		for (i = 0; i < td->len; i++) {
-			if (p[NAND_SMALL_BADBLOCK_POS + i] != td->pattern[i])
-				return -1;
-		}
-	}
 	return 0;
 }
 

@@ -1330,8 +1301,7 @@ static struct nand_bbt_descr bbt_mirror_no_bbt_descr = {
 	.pattern = mirror_pattern
 };
 
-#define BBT_SCAN_OPTIONS (NAND_BBT_SCANLASTPAGE | NAND_BBT_SCAN2NDPAGE | \
-		NAND_BBT_SCANBYTE1AND6)
+#define BBT_SCAN_OPTIONS (NAND_BBT_SCANLASTPAGE | NAND_BBT_SCAN2NDPAGE)
 /**
  * nand_create_default_bbt_descr - [Internal] Creates a BBT descriptor structure
  * @this:	NAND chip to create descriptor for

index 57cc0e6..08ffa21 100644
@@ -98,8 +98,6 @@ struct nand_bbt_descr {
 #define NAND_BBT_SCAN2NDPAGE	0x00004000
 /* Search good / bad pattern on the last page of the eraseblock */
 #define NAND_BBT_SCANLASTPAGE	0x00008000
-/* Chip stores bad block marker on BOTH 1st and 6th bytes of OOB */
-#define NAND_BBT_SCANBYTE1AND6 0x00100000
 /* The nand_bbt_descr was created dynamicaly and must be freed */
 #define NAND_BBT_DYNAMICSTRUCT 0x00200000
 /* The bad block table does not OOB for marker */

index 456fb34..8dc2576 100644
@@ -344,7 +344,7 @@ static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip)
 	struct nand_chip *chip = mtd->priv;
 	u16 bad;
 
-	if (chip->options & NAND_BBT_SCANLASTPAGE)
+	if (chip->bbt_options & NAND_BBT_SCANLASTPAGE)
 		ofs += mtd->erasesize - mtd->writesize;
 
 	page = (int)(ofs >> chip->page_shift) & chip->pagemask;

@@ -396,7 +396,7 @@ static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
 	uint8_t buf[2] = { 0, 0 };
 	int block, ret, i = 0;
 
-	if (chip->options & NAND_BBT_SCANLASTPAGE)
+	if (chip->bbt_options & NAND_BBT_SCANLASTPAGE)
 		ofs += mtd->erasesize - mtd->writesize;
 
 	/* Get block number */

@@ -426,7 +426,7 @@ static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
 
 			i++;
 			ofs += mtd->writesize;
-		} while (!ret && (chip->options & NAND_BBT_SCAN2NDPAGE) &&
+		} while (!ret && (chip->bbt_options & NAND_BBT_SCAN2NDPAGE) &&
 				i < 2);
 
 		nand_release_device(mtd);

@@ -3117,7 +3117,7 @@ ident_done:
 	if ((chip->cellinfo & NAND_CI_CELLTYPE_MSK) &&
 			(*maf_id == NAND_MFR_SAMSUNG ||
 			 *maf_id == NAND_MFR_HYNIX))
-		chip->options |= NAND_BBT_SCANLASTPAGE;
+		chip->bbt_options |= NAND_BBT_SCANLASTPAGE;
 	else if ((!(chip->cellinfo & NAND_CI_CELLTYPE_MSK) &&
 				(*maf_id == NAND_MFR_SAMSUNG ||
 				 *maf_id == NAND_MFR_HYNIX ||

@@ -3125,7 +3125,7 @@ ident_done:
 				 *maf_id == NAND_MFR_AMD)) ||
 			(mtd->writesize == 2048 &&
 			 *maf_id == NAND_MFR_MICRON))
-		chip->options |= NAND_BBT_SCAN2NDPAGE;
+		chip->bbt_options |= NAND_BBT_SCAN2NDPAGE;
 
 	/* Check for AND chips with 4 page planes */
 	if (chip->options & NAND_4PAGE_ARRAY)

index 5ffb9a4..5df01d8 100644
@@ -517,7 +517,7 @@ static int create_bbt(struct mtd_info *mtd, uint8_t *buf,
 		from = (loff_t)startblock << (this->bbt_erase_shift - 1);
 	}
 
-	if (this->options & NAND_BBT_SCANLASTPAGE)
+	if (this->bbt_options & NAND_BBT_SCANLASTPAGE)
 		from += mtd->erasesize - (mtd->writesize * len);
 
 	for (i = startblock; i < numblocks;) {

@@ -1301,7 +1301,6 @@ static struct nand_bbt_descr bbt_mirror_no_bbt_descr = {
 	.pattern = mirror_pattern
 };
 
-#define BBT_SCAN_OPTIONS (NAND_BBT_SCANLASTPAGE | NAND_BBT_SCAN2NDPAGE)
 /**
  * nand_create_default_bbt_descr - [Internal] Creates a BBT descriptor structure
  * @this:	NAND chip to create descriptor for

@@ -1324,7 +1323,7 @@ static int nand_create_default_bbt_descr(struct nand_chip *this)
 		printk(KERN_ERR "nand_create_default_bbt_descr: Out of memory\n");
 		return -ENOMEM;
 	}
-	bd->options = this->options & BBT_SCAN_OPTIONS;
+	bd->options = this->bbt_options;
 	bd->offs = this->badblockpos;
 	bd->len = (this->options & NAND_BUSWIDTH_16) ? 2 : 1;
 	bd->pattern = scan_ff_pattern;

index c2b9ac4..42f70e2 100644
@@ -449,6 +449,9 @@ struct nand_buffers {
  * @options:		[BOARDSPECIFIC] various chip options. They can partly
  *			be set to inform nand_scan about special functionality.
  *			See the defines for further explanation.
+ * @bbt_options:	[INTERN] bad block specific options. All options used
+ *			here must come from bbm.h. By default, these options
+ *			will be copied to the appropriate nand_bbt_descr's.
  * @badblockpos:	[INTERN] position of the bad block marker in the oob
  *			area.
  * @badblockbits:	[INTERN] number of bits to left-shift the bad block

@@ -509,6 +512,7 @@ struct nand_chip {
 
 	int chip_delay;
 	unsigned int options;
+	unsigned int bbt_options;
 
 	int page_shift;
 	int phys_erase_shift;

index 8bc3701..788adc8 100644
@@ -377,7 +377,7 @@ static struct davinci_nand_pdata da830_evm_nand_pdata = {
 	.nr_parts	= ARRAY_SIZE(da830_evm_nand_partitions),
 	.ecc_mode	= NAND_ECC_HW,
 	.ecc_bits	= 4,
-	.options	= NAND_USE_FLASH_BBT,
+	.bbt_options	= NAND_USE_FLASH_BBT,
 	.bbt_td		= &da830_evm_nand_bbt_main_descr,
 	.bbt_md		= &da830_evm_nand_bbt_mirror_descr,
 	.timing         = &da830_evm_nandflash_timing,

index a7b41bf..8bfad01 100644
@@ -225,7 +225,7 @@ static struct davinci_nand_pdata da850_evm_nandflash_data = {
 	.nr_parts	= ARRAY_SIZE(da850_evm_nandflash_partition),
 	.ecc_mode	= NAND_ECC_HW,
 	.ecc_bits	= 4,
-	.options	= NAND_USE_FLASH_BBT,
+	.bbt_options	= NAND_USE_FLASH_BBT,
 	.timing		= &da850_evm_nandflash_timing,
 };
 

index 6e7cad1..d857b70 100644
@@ -77,7 +77,7 @@ static struct davinci_nand_pdata davinci_nand_data = {
 	.parts			= davinci_nand_partitions,
 	.nr_parts		= ARRAY_SIZE(davinci_nand_partitions),
 	.ecc_mode		= NAND_ECC_HW,
-	.options		= NAND_USE_FLASH_BBT,
+	.bbt_options		= NAND_USE_FLASH_BBT,
 	.ecc_bits		= 4,
 };
 

index 543f991..b24dfd0 100644
@@ -74,7 +74,7 @@ static struct davinci_nand_pdata davinci_nand_data = {
 	.parts			= davinci_nand_partitions,
 	.nr_parts		= ARRAY_SIZE(davinci_nand_partitions),
 	.ecc_mode		= NAND_ECC_HW_SYNDROME,
-	.options		= NAND_USE_FLASH_BBT,
+	.bbt_options		= NAND_USE_FLASH_BBT,
 };
 
 static struct resource davinci_nand_resources[] = {

index c67f684..9a74857 100644
@@ -139,7 +139,7 @@ static struct davinci_nand_pdata davinci_nand_data = {
 	.parts			= davinci_nand_partitions,
 	.nr_parts		= ARRAY_SIZE(davinci_nand_partitions),
 	.ecc_mode		= NAND_ECC_HW,
-	.options		= NAND_USE_FLASH_BBT,
+	.bbt_options		= NAND_USE_FLASH_BBT,
 	.ecc_bits		= 4,
 };
 

index 556bbd4..012750f 100644
@@ -150,7 +150,7 @@ static struct davinci_nand_pdata davinci_evm_nandflash_data = {
 	.parts		= davinci_evm_nandflash_partition,
 	.nr_parts	= ARRAY_SIZE(davinci_evm_nandflash_partition),
 	.ecc_mode	= NAND_ECC_HW,
-	.options	= NAND_USE_FLASH_BBT,
+	.bbt_options	= NAND_USE_FLASH_BBT,
 	.timing		= &davinci_evm_nandflash_timing,
 };
 

index 606a6f2..ba52254 100644
@@ -395,7 +395,8 @@ static struct davinci_nand_pdata mityomapl138_nandflash_data = {
 	.parts		= mityomapl138_nandflash_partition,
 	.nr_parts	= ARRAY_SIZE(mityomapl138_nandflash_partition),
 	.ecc_mode	= NAND_ECC_HW,
-	.options	= NAND_USE_FLASH_BBT | NAND_BUSWIDTH_16,
+	.bbt_options	= NAND_USE_FLASH_BBT,
+	.options	= NAND_BUSWIDTH_16,
 	.ecc_bits	= 1, /* 4 bit mode is not supported with 16 bit NAND */
 };
 

index 3e7be2d..89bf0b5 100644
@@ -87,7 +87,7 @@ static struct davinci_nand_pdata davinci_ntosd2_nandflash_data = {
 	.parts		= davinci_ntosd2_nandflash_partition,
 	.nr_parts	= ARRAY_SIZE(davinci_ntosd2_nandflash_partition),
 	.ecc_mode	= NAND_ECC_HW,
-	.options	= NAND_USE_FLASH_BBT,
+	.bbt_options	= NAND_USE_FLASH_BBT,
 };
 
 static struct resource davinci_ntosd2_nandflash_resource[] = {

index 1a656e8..f98896c 100644
@@ -144,7 +144,7 @@ static struct davinci_nand_pdata nand_config = {
 	.parts		= nand_partitions,
 	.nr_parts	= ARRAY_SIZE(nand_partitions),
 	.ecc_mode	= NAND_ECC_HW,
-	.options	= NAND_USE_FLASH_BBT,
+	.bbt_options	= NAND_USE_FLASH_BBT,
 	.ecc_bits	= 1,
 };
 

index 0251510..2c506f9 100644
@@ -74,8 +74,10 @@ struct davinci_nand_pdata {		/* platform_data */
 	nand_ecc_modes_t	ecc_mode;
 	u8			ecc_bits;
 
-	/* e.g. NAND_BUSWIDTH_16 or NAND_USE_FLASH_BBT */
+	/* e.g. NAND_BUSWIDTH_16 */
 	unsigned		options;
+	/* e.g. NAND_USE_FLASH_BBT */
+	unsigned		bbt_options;
 
 	/* Main and mirror bbt descriptor overrides */
 	struct nand_bbt_descr	*bbt_td;

index 6b7b541..e5ca57c 100644
@@ -275,7 +275,7 @@ static struct platform_nand_data ts78xx_ts_nand_data = {
 		.partitions		= ts78xx_ts_nand_parts,
 		.nr_partitions		= ARRAY_SIZE(ts78xx_ts_nand_parts),
 		.chip_delay		= 15,
-		.options		= NAND_USE_FLASH_BBT,
+		.bbt_options		= NAND_USE_FLASH_BBT,
 	},
 	.ctrl	= {
 		/*

index f58f2c1..fdd11c1 100644
@@ -163,7 +163,7 @@ struct mtd_info *__init crisv32_nand_flash_probe(void)
 	this->ecc.mode = NAND_ECC_SOFT;
 
 	/* Enable the following for a flash based bad block table */
-	/* this->options = NAND_USE_FLASH_BBT; */
+	/* this->bbt_options = NAND_USE_FLASH_BBT; */
 
 	/* Scan to find existence of the device */
 	if (nand_scan(crisv32_mtd, 1)) {

index d5b0cc9..3368177 100644
@@ -154,7 +154,7 @@ struct mtd_info *__init crisv32_nand_flash_probe(void)
 	this->ecc.mode = NAND_ECC_SOFT;
 
 	/* Enable the following for a flash based bad block table */
-	/* this->options = NAND_USE_FLASH_BBT; */
+	/* this->bbt_options = NAND_USE_FLASH_BBT; */
 
 	/* Scan to find existence of the device */
 	if (nand_scan(crisv32_mtd, 1)) {

index b300705..4afdc83 100644
@@ -582,7 +582,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
 
 	if (on_flash_bbt) {
 		printk(KERN_INFO "atmel_nand: Use On Flash BBT\n");
-		nand_chip->options |= NAND_USE_FLASH_BBT;
+		nand_chip->bbt_options |= NAND_USE_FLASH_BBT;
 	}
 
 	if (!cpu_has_dma())

index eddc9a2..adf934d 100644
@@ -172,9 +172,9 @@ static int __init autcpu12_init(void)
 
 	/* Enable the following for a flash based bad block table */
 	/*
-	   this->options = NAND_USE_FLASH_BBT;
+	   this->bbt_options = NAND_USE_FLASH_BBT;
 	 */
-	this->options = NAND_USE_FLASH_BBT;
+	this->bbt_options = NAND_USE_FLASH_BBT;
 
 	/* Scan to find existence of the device */
 	if (nand_scan(autcpu12_mtd, 1)) {

index 9ec2807..8ae9ad9 100644
@@ -474,7 +474,7 @@ static int __devinit bcm_umi_nand_probe(struct platform_device *pdev)
 
 #if NAND_ECC_BCH
 	if (board_mtd->writesize > 512) {
-		if (this->options & NAND_USE_FLASH_BBT)
+		if (this->bbt_options & NAND_USE_FLASH_BBT)
 			largepage_bbt.options = NAND_BBT_SCAN2NDPAGE;
 		this->badblock_pattern = &largepage_bbt;
 	}

index 87ebb4e..7dd7d84 100644
@@ -686,7 +686,8 @@ static int __devinit cafe_nand_probe(struct pci_dev *pdev,
 	cafe->nand.chip_delay = 0;
 
 	/* Enable the following for a flash based bad block table */
-	cafe->nand.options = NAND_USE_FLASH_BBT | NAND_NO_AUTOINCR | NAND_OWN_BUFFERS;
+	cafe->nand.bbt_options = NAND_USE_FLASH_BBT;
+	cafe->nand.options = NAND_NO_AUTOINCR | NAND_OWN_BUFFERS;
 
 	if (skipbbt) {
 		cafe->nand.options |= NAND_SKIP_BBTSCAN;

index f59ad1f..05adedd 100644
@@ -239,7 +239,8 @@ static int __init cs553x_init_one(int cs, int mmio, unsigned long adr)
 	this->ecc.correct  = nand_correct_data;
 
 	/* Enable the following for a flash based bad block table */
-	this->options = NAND_USE_FLASH_BBT | NAND_NO_AUTOINCR;
+	this->bbt_options = NAND_USE_FLASH_BBT;
+	this->options = NAND_NO_AUTOINCR;
 
 	/* Scan to find existence of the device */
 	if (nand_scan(new_mtd, 1)) {

index 1f34951..69f7019 100644
@@ -581,7 +581,9 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
 	info->chip.chip_delay	= 0;
 	info->chip.select_chip	= nand_davinci_select_chip;
 
-	/* options such as NAND_USE_FLASH_BBT or 16-bit widths */
+	/* options such as NAND_USE_FLASH_BBT */
+	info->chip.bbt_options	= pdata->bbt_options;
+	/* options such as 16-bit widths */
 	info->chip.options	= pdata->options;
 	info->chip.bbt_td	= pdata->bbt_td;
 	info->chip.bbt_md	= pdata->bbt_md;

index d527621..dbb6fba 100644
@@ -1577,7 +1577,8 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	denali->nand.bbt_md = &bbt_mirror_descr;
 
 	/* skip the scan for now until we have OOB read and write support */
-	denali->nand.options |= NAND_USE_FLASH_BBT | NAND_SKIP_BBTSCAN;
+	denali->nand.bbt_options |= NAND_USE_FLASH_BBT;
+	denali->nand.options |= NAND_SKIP_BBTSCAN;
 	denali->nand.ecc.mode = NAND_ECC_HW_SYNDROME;
 
 	/* Denali Controller only support 15bit and 8bit ECC in MRST,

index 7837728..f70bc73 100644
@@ -1652,7 +1652,7 @@ static int __init doc_probe(unsigned long physadr)
 	nand->ecc.mode		= NAND_ECC_HW_SYNDROME;
 	nand->ecc.size		= 512;
 	nand->ecc.bytes		= 6;
-	nand->options		= NAND_USE_FLASH_BBT;
+	nand->bbt_options	= NAND_USE_FLASH_BBT;
 
 	doc->physadr		= physadr;
 	doc->virtadr		= virtadr;

index 0bb254c..a06b59c 100644
@@ -791,8 +791,8 @@ static int fsl_elbc_chip_init(struct fsl_elbc_mtd *priv)
 	chip->bbt_md = &bbt_mirror_descr;
 
 	/* set up nand options */
-	chip->options = NAND_NO_READRDY | NAND_NO_AUTOINCR |
-			NAND_USE_FLASH_BBT;
+	chip->options = NAND_NO_READRDY | NAND_NO_AUTOINCR;
+	chip->bbt_options = NAND_USE_FLASH_BBT;
 
 	chip->controller = &elbc_fcm_ctrl->controller;
 	chip->priv = priv;

index 2f7c930..d611542 100644
@@ -735,7 +735,8 @@ static int __devinit mpc5121_nfc_probe(struct platform_device *op)
 	chip->write_buf = mpc5121_nfc_write_buf;
 	chip->verify_buf = mpc5121_nfc_verify_buf;
 	chip->select_chip = mpc5121_nfc_select_chip;
-	chip->options = NAND_NO_AUTOINCR | NAND_USE_FLASH_BBT;
+	chip->options = NAND_NO_AUTOINCR;
+	chip->bbt_options = NAND_USE_FLASH_BBT;
 	chip->ecc.mode = NAND_ECC_SOFT;
 
 	/* Support external chip-select logic on ADS5121 board */

index 90df34c..ed68fde 100644
@@ -1179,7 +1179,7 @@ static int __init mxcnd_probe(struct platform_device *pdev)
 		this->bbt_td = &bbt_main_descr;
 		this->bbt_md = &bbt_mirror_descr;
 		/* update flash based bbt */
-		this->options |= NAND_USE_FLASH_BBT;
+		this->bbt_options |= NAND_USE_FLASH_BBT;
 	}
 
 	init_completion(&host->op_completion);

index 8dc2576..221a76a 100644
@@ -405,7 +405,7 @@ static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
 		chip->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1);
 
 	/* Do we have a flash based bad block table ? */
-	if (chip->options & NAND_USE_FLASH_BBT)
+	if (chip->bbt_options & NAND_USE_FLASH_BBT)
 		ret = nand_update_bbt(mtd, ofs);
 	else {
 		nand_get_device(chip, mtd, FL_WRITING);

index 5df01d8..66f93e2 100644
@@ -36,9 +36,9 @@
  * The table is marked in the OOB area with an ident pattern and a version
  * number which indicates which of both tables is more up to date. If the NAND
  * controller needs the complete OOB area for the ECC information then the
- * option NAND_USE_FLASH_BBT_NO_OOB should be used: it moves the ident pattern
- * and the version byte into the data area and the OOB area will remain
- * untouched.
+ * option NAND_BBT_NO_OOB should be used (along with NAND_USE_FLASH_BBT, of
+ * course): it moves the ident pattern and the version byte into the data area
+ * and the OOB area will remain untouched.
  *
  * The table uses 2 bits per block
  * 11b:		block is good

@@ -1082,16 +1082,16 @@ static void verify_bbt_descr(struct mtd_info *mtd, struct nand_bbt_descr *bd)
 	pattern_len = bd->len;
 	bits = bd->options & NAND_BBT_NRBITS_MSK;
 
-	BUG_ON((this->options & NAND_USE_FLASH_BBT_NO_OOB) &&
-			!(this->options & NAND_USE_FLASH_BBT));
+	BUG_ON((this->bbt_options & NAND_BBT_NO_OOB) &&
+			!(this->bbt_options & NAND_USE_FLASH_BBT));
 	BUG_ON(!bits);
 
 	if (bd->options & NAND_BBT_VERSION)
 		pattern_len++;
 
 	if (bd->options & NAND_BBT_NO_OOB) {
-		BUG_ON(!(this->options & NAND_USE_FLASH_BBT));
-		BUG_ON(!(this->options & NAND_USE_FLASH_BBT_NO_OOB));
+		BUG_ON(!(this->bbt_options & NAND_USE_FLASH_BBT));
+		BUG_ON(!(this->bbt_options & NAND_BBT_NO_OOB));
 		BUG_ON(bd->offs);
 		if (bd->options & NAND_BBT_VERSION)
 			BUG_ON(bd->veroffs != bd->len);

@@ -1357,15 +1357,15 @@ int nand_default_bbt(struct mtd_info *mtd)
 			this->bbt_td = &bbt_main_descr;
 			this->bbt_md = &bbt_mirror_descr;
 		}
-		this->options |= NAND_USE_FLASH_BBT;
+		this->bbt_options |= NAND_USE_FLASH_BBT;
 		return nand_scan_bbt(mtd, &agand_flashbased);
 	}
 
 	/* Is a flash based bad block table requested ? */
-	if (this->options & NAND_USE_FLASH_BBT) {
+	if (this->bbt_options & NAND_USE_FLASH_BBT) {
 		/* Use the default pattern descriptors */
 		if (!this->bbt_td) {
-			if (this->options & NAND_USE_FLASH_BBT_NO_OOB) {
+			if (this->bbt_options & NAND_BBT_NO_OOB) {
 				this->bbt_td = &bbt_main_no_bbt_descr;
 				this->bbt_md = &bbt_mirror_no_bbt_descr;
 			} else {

index 357e8c5..1856c42 100644
@@ -2273,9 +2273,9 @@ static int __init ns_init_module(void)
 
 	switch (bbt) {
 	case 2:
-		 chip->options |= NAND_USE_FLASH_BBT_NO_OOB;
+		 chip->bbt_options |= NAND_BBT_NO_OOB;
 	case 1:
-		 chip->options |= NAND_USE_FLASH_BBT;
+		 chip->bbt_options |= NAND_USE_FLASH_BBT;
 	case 0:
 		break;
 	default:

index b1aa41b..1c17f09 100644
@@ -155,7 +155,8 @@ static int __devinit pasemi_nand_probe(struct platform_device *ofdev)
 	chip->ecc.mode = NAND_ECC_SOFT;
 
 	/* Enable the following for a flash based bad block table */
-	chip->options = NAND_USE_FLASH_BBT | NAND_NO_AUTOINCR;
+	chip->options = NAND_NO_AUTOINCR;
+	chip->bbt_options = NAND_USE_FLASH_BBT;
 
 	/* Scan to find existence of the device */
 	if (nand_scan(pasemi_nand_mtd, 1)) {

index 4405468..370516c 100644
@@ -880,8 +880,10 @@ static void s3c2410_nand_init_chip(struct s3c2410_nand_info *info,
 	/* If you use u-boot BBT creation code, specifying this flag will
 	 * let the kernel fish out the BBT from the NAND, and also skip the
 	 * full NAND scan that can take 1/2s or so. Little things... */
-	if (set->flash_bbt)
-		chip->options |= NAND_USE_FLASH_BBT | NAND_SKIP_BBTSCAN;
+	if (set->flash_bbt) {
+		chip->bbt_options |= NAND_USE_FLASH_BBT;
+		chip->options |= NAND_SKIP_BBTSCAN;
+	}
 }
 
 /**

index 08ffa21..7929514 100644
@@ -100,8 +100,13 @@ struct nand_bbt_descr {
 #define NAND_BBT_SCANLASTPAGE	0x00008000
 /* The nand_bbt_descr was created dynamicaly and must be freed */
 #define NAND_BBT_DYNAMICSTRUCT 0x00200000
-/* The bad block table does not OOB for marker */
-#define NAND_BBT_NO_OOB		0x00400000
+/*
+ * Use a flash based bad block table. By default, OOB identifier is saved in
+ * OOB area. This option is passed to the default bad block table function.
+ */
+#define NAND_USE_FLASH_BBT	0x00040000
+/* Do not store flash based bad block table in OOB area; store it in-band */
+#define NAND_BBT_NO_OOB		0x00080000
 
 /* The maximum number of blocks to scan for a bbt */
 #define NAND_BBT_SCAN_MAXBLOCKS	4

index 42f70e2..f68e8cb 100644
@@ -219,11 +219,6 @@ typedef enum {
 #define NAND_CHIPOPTIONS_MSK	(0x0000ffff & ~NAND_NO_AUTOINCR)
 
 /* Non chip related options */
-/*
- * Use a flash based bad block table. OOB identifier is saved in OOB area.
- * This option is passed to the default bad block table function.
- */
-#define NAND_USE_FLASH_BBT	0x00010000
 /* This option skips the bbt scan during initialization. */
 #define NAND_SKIP_BBTSCAN	0x00020000
 /*

@@ -233,11 +228,6 @@ typedef enum {
 #define NAND_OWN_BUFFERS	0x00040000
 /* Chip may not exist, so silence any errors in scan */
 #define NAND_SCAN_SILENT_NODEV	0x00080000
-/*
- * If passed additionally to NAND_USE_FLASH_BBT then BBT code will not touch
- * the OOB area.
- */
-#define NAND_USE_FLASH_BBT_NO_OOB	0x00800000
 /* Create an empty BBT with no vendor information if the BBT is available */
 #define NAND_CREATE_EMPTY_BBT		0x01000000
 

index 788adc8..80368a1 100644
@@ -377,7 +377,7 @@ static struct davinci_nand_pdata da830_evm_nand_pdata = {
 	.nr_parts	= ARRAY_SIZE(da830_evm_nand_partitions),
 	.ecc_mode	= NAND_ECC_HW,
 	.ecc_bits	= 4,
-	.bbt_options	= NAND_USE_FLASH_BBT,
+	.bbt_options	= NAND_BBT_USE_FLASH,
 	.bbt_td		= &da830_evm_nand_bbt_main_descr,
 	.bbt_md		= &da830_evm_nand_bbt_mirror_descr,
 	.timing         = &da830_evm_nandflash_timing,

index 8bfad01..8bfde41 100644
@@ -225,7 +225,7 @@ static struct davinci_nand_pdata da850_evm_nandflash_data = {
 	.nr_parts	= ARRAY_SIZE(da850_evm_nandflash_partition),
 	.ecc_mode	= NAND_ECC_HW,
 	.ecc_bits	= 4,
-	.bbt_options	= NAND_USE_FLASH_BBT,
+	.bbt_options	= NAND_BBT_USE_FLASH,
 	.timing		= &da850_evm_nandflash_timing,
 };
 

index d857b70..530d44a 100644
@@ -77,7 +77,7 @@ static struct davinci_nand_pdata davinci_nand_data = {
 	.parts			= davinci_nand_partitions,
 	.nr_parts		= ARRAY_SIZE(davinci_nand_partitions),
 	.ecc_mode		= NAND_ECC_HW,
-	.bbt_options		= NAND_USE_FLASH_BBT,
+	.bbt_options		= NAND_BBT_USE_FLASH,
 	.ecc_bits		= 4,
 };
 

index b24dfd0..971c4e0 100644
@@ -74,7 +74,7 @@ static struct davinci_nand_pdata davinci_nand_data = {
 	.parts			= davinci_nand_partitions,
 	.nr_parts		= ARRAY_SIZE(davinci_nand_partitions),
 	.ecc_mode		= NAND_ECC_HW_SYNDROME,
-	.bbt_options		= NAND_USE_FLASH_BBT,
+	.bbt_options		= NAND_BBT_USE_FLASH,
 };
 
 static struct resource davinci_nand_resources[] = {

index 9a74857..1e4be46 100644
@@ -139,7 +139,7 @@ static struct davinci_nand_pdata davinci_nand_data = {
 	.parts			= davinci_nand_partitions,
 	.nr_parts		= ARRAY_SIZE(davinci_nand_partitions),
 	.ecc_mode		= NAND_ECC_HW,
-	.bbt_options		= NAND_USE_FLASH_BBT,
+	.bbt_options		= NAND_BBT_USE_FLASH,
 	.ecc_bits		= 4,
 };
 

index 012750f..e70cb0d 100644
@@ -150,7 +150,7 @@ static struct davinci_nand_pdata davinci_evm_nandflash_data = {
 	.parts		= davinci_evm_nandflash_partition,
 	.nr_parts	= ARRAY_SIZE(davinci_evm_nandflash_partition),
 	.ecc_mode	= NAND_ECC_HW,
-	.bbt_options	= NAND_USE_FLASH_BBT,
+	.bbt_options	= NAND_BBT_USE_FLASH,
 	.timing		= &davinci_evm_nandflash_timing,
 };
 

index ba52254..7b57373 100644
@@ -395,7 +395,7 @@ static struct davinci_nand_pdata mityomapl138_nandflash_data = {
 	.parts		= mityomapl138_nandflash_partition,
 	.nr_parts	= ARRAY_SIZE(mityomapl138_nandflash_partition),
 	.ecc_mode	= NAND_ECC_HW,
-	.bbt_options	= NAND_USE_FLASH_BBT,
+	.bbt_options	= NAND_BBT_USE_FLASH,
 	.options	= NAND_BUSWIDTH_16,
 	.ecc_bits	= 1, /* 4 bit mode is not supported with 16 bit NAND */
 };

index 89bf0b5..5eb8ef3 100644
@@ -87,7 +87,7 @@ static struct davinci_nand_pdata davinci_ntosd2_nandflash_data = {
 	.parts		= davinci_ntosd2_nandflash_partition,
 	.nr_parts	= ARRAY_SIZE(davinci_ntosd2_nandflash_partition),
 	.ecc_mode	= NAND_ECC_HW,
-	.bbt_options	= NAND_USE_FLASH_BBT,
+	.bbt_options	= NAND_BBT_USE_FLASH,
 };
 
 static struct resource davinci_ntosd2_nandflash_resource[] = {

index f98896c..c5feb9b 100644
@@ -144,7 +144,7 @@ static struct davinci_nand_pdata nand_config = {
 	.parts		= nand_partitions,
 	.nr_parts	= ARRAY_SIZE(nand_partitions),
 	.ecc_mode	= NAND_ECC_HW,
-	.bbt_options	= NAND_USE_FLASH_BBT,
+	.bbt_options	= NAND_BBT_USE_FLASH,
 	.ecc_bits	= 1,
 };
 

index 2c506f9..1cf555a 100644
@@ -76,7 +76,7 @@ struct davinci_nand_pdata {		/* platform_data */
 
 	/* e.g. NAND_BUSWIDTH_16 */
 	unsigned		options;
-	/* e.g. NAND_USE_FLASH_BBT */
+	/* e.g. NAND_BBT_USE_FLASH */
 	unsigned		bbt_options;
 
 	/* Main and mirror bbt descriptor overrides */

index e5ca57c..8ae5301 100644
@@ -275,7 +275,7 @@ static struct platform_nand_data ts78xx_ts_nand_data = {
 		.partitions		= ts78xx_ts_nand_parts,
 		.nr_partitions		= ARRAY_SIZE(ts78xx_ts_nand_parts),
 		.chip_delay		= 15,
-		.bbt_options		= NAND_USE_FLASH_BBT,
+		.bbt_options		= NAND_BBT_USE_FLASH,
 	},
 	.ctrl	= {
 		/*

index fdd11c1..7fb5212 100644
@@ -163,7 +163,7 @@ struct mtd_info *__init crisv32_nand_flash_probe(void)
 	this->ecc.mode = NAND_ECC_SOFT;
 
 	/* Enable the following for a flash based bad block table */
-	/* this->bbt_options = NAND_USE_FLASH_BBT; */
+	/* this->bbt_options = NAND_BBT_USE_FLASH; */
 
 	/* Scan to find existence of the device */
 	if (nand_scan(crisv32_mtd, 1)) {

index 3368177..e032384 100644
@@ -154,7 +154,7 @@ struct mtd_info *__init crisv32_nand_flash_probe(void)
 	this->ecc.mode = NAND_ECC_SOFT;
 
 	/* Enable the following for a flash based bad block table */
-	/* this->bbt_options = NAND_USE_FLASH_BBT; */
+	/* this->bbt_options = NAND_BBT_USE_FLASH; */
 
 	/* Scan to find existence of the device */
 	if (nand_scan(crisv32_mtd, 1)) {

index 4afdc83..dc9b8d6 100644
@@ -582,7 +582,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
 
 	if (on_flash_bbt) {
 		printk(KERN_INFO "atmel_nand: Use On Flash BBT\n");
-		nand_chip->bbt_options |= NAND_USE_FLASH_BBT;
+		nand_chip->bbt_options |= NAND_BBT_USE_FLASH;
 	}
 
 	if (!cpu_has_dma())

index adf934d..2e42ec2 100644
@@ -172,9 +172,9 @@ static int __init autcpu12_init(void)
 
 	/* Enable the following for a flash based bad block table */
 	/*
-	   this->bbt_options = NAND_USE_FLASH_BBT;
+	   this->bbt_options = NAND_BBT_USE_FLASH;
 	 */
-	this->bbt_options = NAND_USE_FLASH_BBT;
+	this->bbt_options = NAND_BBT_USE_FLASH;
 
 	/* Scan to find existence of the device */
 	if (nand_scan(autcpu12_mtd, 1)) {

index 8ae9ad9..7ac8607 100644
@@ -474,7 +474,7 @@ static int __devinit bcm_umi_nand_probe(struct platform_device *pdev)
 
 #if NAND_ECC_BCH
 	if (board_mtd->writesize > 512) {
-		if (this->bbt_options & NAND_USE_FLASH_BBT)
+		if (this->bbt_options & NAND_BBT_USE_FLASH)
 			largepage_bbt.options = NAND_BBT_SCAN2NDPAGE;
 		this->badblock_pattern = &largepage_bbt;
 	}

index 7dd7d84..d0eed49 100644
@@ -686,7 +686,7 @@ static int __devinit cafe_nand_probe(struct pci_dev *pdev,
 	cafe->nand.chip_delay = 0;
 
 	/* Enable the following for a flash based bad block table */
-	cafe->nand.bbt_options = NAND_USE_FLASH_BBT;
+	cafe->nand.bbt_options = NAND_BBT_USE_FLASH;
 	cafe->nand.options = NAND_NO_AUTOINCR | NAND_OWN_BUFFERS;
 
 	if (skipbbt) {

index 05adedd..b354961 100644
@@ -239,7 +239,7 @@ static int __init cs553x_init_one(int cs, int mmio, unsigned long adr)
 	this->ecc.correct  = nand_correct_data;
 
 	/* Enable the following for a flash based bad block table */
-	this->bbt_options = NAND_USE_FLASH_BBT;
+	this->bbt_options = NAND_BBT_USE_FLASH;
 	this->options = NAND_NO_AUTOINCR;
 
 	/* Scan to find existence of the device */

index 69f7019..a4c82b4 100644
@@ -581,7 +581,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
 	info->chip.chip_delay	= 0;
 	info->chip.select_chip	= nand_davinci_select_chip;
 
-	/* options such as NAND_USE_FLASH_BBT */
+	/* options such as NAND_BBT_USE_FLASH */
 	info->chip.bbt_options	= pdata->bbt_options;
 	/* options such as 16-bit widths */
 	info->chip.options	= pdata->options;

index dbb6fba..ee30145 100644
@@ -1577,7 +1577,7 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	denali->nand.bbt_md = &bbt_mirror_descr;
 
 	/* skip the scan for now until we have OOB read and write support */
-	denali->nand.bbt_options |= NAND_USE_FLASH_BBT;
+	denali->nand.bbt_options |= NAND_BBT_USE_FLASH;
 	denali->nand.options |= NAND_SKIP_BBTSCAN;
 	denali->nand.ecc.mode = NAND_ECC_HW_SYNDROME;
 

index f70bc73..b657d7f 100644
@@ -1652,7 +1652,7 @@ static int __init doc_probe(unsigned long physadr)
 	nand->ecc.mode		= NAND_ECC_HW_SYNDROME;
 	nand->ecc.size		= 512;
 	nand->ecc.bytes		= 6;
-	nand->bbt_options	= NAND_USE_FLASH_BBT;
+	nand->bbt_options	= NAND_BBT_USE_FLASH;
 
 	doc->physadr		= physadr;
 	doc->virtadr		= virtadr;

index a06b59c..f3384fa 100644
@@ -792,7 +792,7 @@ static int fsl_elbc_chip_init(struct fsl_elbc_mtd *priv)
 
 	/* set up nand options */
 	chip->options = NAND_NO_READRDY | NAND_NO_AUTOINCR;
-	chip->bbt_options = NAND_USE_FLASH_BBT;
+	chip->bbt_options = NAND_BBT_USE_FLASH;
 
 	chip->controller = &elbc_fcm_ctrl->controller;
 	chip->priv = priv;

index d611542..e0e0846 100644
@@ -736,7 +736,7 @@ static int __devinit mpc5121_nfc_probe(struct platform_device *op)
 	chip->verify_buf = mpc5121_nfc_verify_buf;
 	chip->select_chip = mpc5121_nfc_select_chip;
 	chip->options = NAND_NO_AUTOINCR;
-	chip->bbt_options = NAND_USE_FLASH_BBT;
+	chip->bbt_options = NAND_BBT_USE_FLASH;
 	chip->ecc.mode = NAND_ECC_SOFT;
 
 	/* Support external chip-select logic on ADS5121 board */

index ed68fde..ca42c8f 100644
@@ -1179,7 +1179,7 @@ static int __init mxcnd_probe(struct platform_device *pdev)
 		this->bbt_td = &bbt_main_descr;
 		this->bbt_md = &bbt_mirror_descr;
 		/* update flash based bbt */
-		this->bbt_options |= NAND_USE_FLASH_BBT;
+		this->bbt_options |= NAND_BBT_USE_FLASH;
 	}
 
 	init_completion(&host->op_completion);

index 221a76a..9343cbb 100644
@@ -405,7 +405,7 @@ static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs)
 		chip->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1);
 
 	/* Do we have a flash based bad block table ? */
-	if (chip->bbt_options & NAND_USE_FLASH_BBT)
+	if (chip->bbt_options & NAND_BBT_USE_FLASH)
 		ret = nand_update_bbt(mtd, ofs);
 	else {
 		nand_get_device(chip, mtd, FL_WRITING);

index 66f93e2..dfea9fd 100644
@@ -14,7 +14,7 @@
  *
  * When nand_scan_bbt is called, then it tries to find the bad block table
  * depending on the options in the BBT descriptor(s). If no flash based BBT
- * (NAND_USE_FLASH_BBT) is specified then the device is scanned for factory
+ * (NAND_BBT_USE_FLASH) is specified then the device is scanned for factory
  * marked good / bad blocks. This information is used to create a memory BBT.
  * Once a new bad block is discovered then the "factory" information is updated
  * on the device.

@@ -36,7 +36,7 @@
  * The table is marked in the OOB area with an ident pattern and a version
  * number which indicates which of both tables is more up to date. If the NAND
  * controller needs the complete OOB area for the ECC information then the
- * option NAND_BBT_NO_OOB should be used (along with NAND_USE_FLASH_BBT, of
+ * option NAND_BBT_NO_OOB should be used (along with NAND_BBT_USE_FLASH, of
  * course): it moves the ident pattern and the version byte into the data area
  * and the OOB area will remain untouched.
  *

@@ -1083,14 +1083,14 @@ static void verify_bbt_descr(struct mtd_info *mtd, struct nand_bbt_descr *bd)
 	bits = bd->options & NAND_BBT_NRBITS_MSK;
 
 	BUG_ON((this->bbt_options & NAND_BBT_NO_OOB) &&
-			!(this->bbt_options & NAND_USE_FLASH_BBT));
+			!(this->bbt_options & NAND_BBT_USE_FLASH));
 	BUG_ON(!bits);
 
 	if (bd->options & NAND_BBT_VERSION)
 		pattern_len++;
 
 	if (bd->options & NAND_BBT_NO_OOB) {
-		BUG_ON(!(this->bbt_options & NAND_USE_FLASH_BBT));
+		BUG_ON(!(this->bbt_options & NAND_BBT_USE_FLASH));
 		BUG_ON(!(this->bbt_options & NAND_BBT_NO_OOB));
 		BUG_ON(bd->offs);
 		if (bd->options & NAND_BBT_VERSION)

@@ -1357,12 +1357,12 @@ int nand_default_bbt(struct mtd_info *mtd)
 			this->bbt_td = &bbt_main_descr;
 			this->bbt_md = &bbt_mirror_descr;
 		}
-		this->bbt_options |= NAND_USE_FLASH_BBT;
+		this->bbt_options |= NAND_BBT_USE_FLASH;
 		return nand_scan_bbt(mtd, &agand_flashbased);
 	}
 
 	/* Is a flash based bad block table requested ? */
-	if (this->bbt_options & NAND_USE_FLASH_BBT) {
+	if (this->bbt_options & NAND_BBT_USE_FLASH) {
 		/* Use the default pattern descriptors */
 		if (!this->bbt_td) {
 			if (this->bbt_options & NAND_BBT_NO_OOB) {

index 1856c42..34c03be 100644
@@ -2275,7 +2275,7 @@ static int __init ns_init_module(void)
 	case 2:
 		 chip->bbt_options |= NAND_BBT_NO_OOB;
 	case 1:
-		 chip->bbt_options |= NAND_USE_FLASH_BBT;
+		 chip->bbt_options |= NAND_BBT_USE_FLASH;
 	case 0:
 		break;
 	default:

index 1c17f09..a97264e 100644
@@ -156,7 +156,7 @@ static int __devinit pasemi_nand_probe(struct platform_device *ofdev)
 
 	/* Enable the following for a flash based bad block table */
 	chip->options = NAND_NO_AUTOINCR;
-	chip->bbt_options = NAND_USE_FLASH_BBT;
+	chip->bbt_options = NAND_BBT_USE_FLASH;
 
 	/* Scan to find existence of the device */
 	if (nand_scan(pasemi_nand_mtd, 1)) {

index 370516c..ec28079 100644
@@ -881,7 +881,7 @@ static void s3c2410_nand_init_chip(struct s3c2410_nand_info *info,
 	 * let the kernel fish out the BBT from the NAND, and also skip the
 	 * full NAND scan that can take 1/2s or so. Little things... */
 	if (set->flash_bbt) {
-		chip->bbt_options |= NAND_USE_FLASH_BBT;
+		chip->bbt_options |= NAND_BBT_USE_FLASH;
 		chip->options |= NAND_SKIP_BBTSCAN;
 	}
 }

index 7929514..ff18c08 100644
@@ -104,7 +104,7 @@ struct nand_bbt_descr {
  * Use a flash based bad block table. By default, OOB identifier is saved in
  * OOB area. This option is passed to the default bad block table function.
  */
-#define NAND_USE_FLASH_BBT	0x00040000
+#define NAND_BBT_USE_FLASH	0x00040000
 /* Do not store flash based bad block table in OOB area; store it in-band */
 #define NAND_BBT_NO_OOB		0x00080000
 

index dfea9fd..2e4e259 100644
@@ -970,7 +970,7 @@ static int check_create(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_desc
 			continue;
 
 		/* Create the table in memory by scanning the chip(s) */
-		if (!(this->options & NAND_CREATE_EMPTY_BBT))
+		if (!(this->bbt_options & NAND_CREATE_EMPTY_BBT))
 			create_bbt(mtd, buf, bd, chipsel);
 
 		td->version[i] = 1;

index ff18c08..3cf4a8a 100644
@@ -86,6 +86,13 @@ struct nand_bbt_descr {
 #define NAND_BBT_VERSION	0x00000100
 /* Create a bbt if none exists */
 #define NAND_BBT_CREATE		0x00000200
+/*
+ * Create an empty BBT with no vendor information. Vendor's information may be
+ * unavailable, for example, if the NAND controller has a different data and OOB
+ * layout or if this information is already purged. Must be used in conjunction
+ * with NAND_BBT_CREATE.
+ */
+#define NAND_CREATE_EMPTY_BBT	0x01000000
 /* Search good / bad pattern through all pages of a block */
 #define NAND_BBT_SCANALLPAGES	0x00000400
 /* Scan block empty during good / bad block scan */

index f68e8cb..4e9e88b 100644
@@ -228,8 +228,6 @@ typedef enum {
 #define NAND_OWN_BUFFERS	0x00040000
 /* Chip may not exist, so silence any errors in scan */
 #define NAND_SCAN_SILENT_NODEV	0x00080000
-/* Create an empty BBT with no vendor information if the BBT is available */
-#define NAND_CREATE_EMPTY_BBT		0x01000000
 
 /* Options set by nand scan */
 /* Nand scan has allocated controller struct */

index 2e4e259..9af703d 100644
@@ -970,7 +970,7 @@ static int check_create(struct mtd_info *mtd, uint8_t *buf, struct nand_bbt_desc
 			continue;
 
 		/* Create the table in memory by scanning the chip(s) */
-		if (!(this->bbt_options & NAND_CREATE_EMPTY_BBT))
+		if (!(this->bbt_options & NAND_BBT_CREATE_EMPTY))
 			create_bbt(mtd, buf, bd, chipsel);
 
 		td->version[i] = 1;

index 3cf4a8a..0fa030a 100644
@@ -92,7 +92,7 @@ struct nand_bbt_descr {
  * layout or if this information is already purged. Must be used in conjunction
  * with NAND_BBT_CREATE.
  */
-#define NAND_CREATE_EMPTY_BBT	0x01000000
+#define NAND_BBT_CREATE_EMPTY	0x01000000
 /* Search good / bad pattern through all pages of a block */
 #define NAND_BBT_SCANALLPAGES	0x00000400
 /* Scan block empty during good / bad block scan */

index 0fa030a..57d6a8d 100644
@@ -92,28 +92,29 @@ struct nand_bbt_descr {
  * layout or if this information is already purged. Must be used in conjunction
  * with NAND_BBT_CREATE.
  */
-#define NAND_BBT_CREATE_EMPTY	0x01000000
+#define NAND_BBT_CREATE_EMPTY	0x00000400
 /* Search good / bad pattern through all pages of a block */
-#define NAND_BBT_SCANALLPAGES	0x00000400
+#define NAND_BBT_SCANALLPAGES	0x00000800
 /* Scan block empty during good / bad block scan */
-#define NAND_BBT_SCANEMPTY	0x00000800
+#define NAND_BBT_SCANEMPTY	0x00001000
 /* Write bbt if neccecary */
-#define NAND_BBT_WRITE		0x00001000
+#define NAND_BBT_WRITE		0x00002000
 /* Read and write back block contents when writing bbt */
-#define NAND_BBT_SAVECONTENT	0x00002000
+#define NAND_BBT_SAVECONTENT	0x00004000
 /* Search good / bad pattern on the first and the second page */
-#define NAND_BBT_SCAN2NDPAGE	0x00004000
+#define NAND_BBT_SCAN2NDPAGE	0x00008000
 /* Search good / bad pattern on the last page of the eraseblock */
-#define NAND_BBT_SCANLASTPAGE	0x00008000
-/* The nand_bbt_descr was created dynamicaly and must be freed */
-#define NAND_BBT_DYNAMICSTRUCT 0x00200000
+#define NAND_BBT_SCANLASTPAGE	0x00010000
 /*
  * Use a flash based bad block table. By default, OOB identifier is saved in
  * OOB area. This option is passed to the default bad block table function.
  */
-#define NAND_BBT_USE_FLASH	0x00040000
+#define NAND_BBT_USE_FLASH	0x00020000
 /* Do not store flash based bad block table in OOB area; store it in-band */
-#define NAND_BBT_NO_OOB		0x00080000
+#define NAND_BBT_NO_OOB		0x00040000
+
+/* The nand_bbt_descr was created dynamicaly and must be freed */
+#define NAND_BBT_DYNAMICSTRUCT	0x80000000
 
 /* The maximum number of blocks to scan for a bbt */
 #define NAND_BBT_SCAN_MAXBLOCKS	4

index 4e9e88b..585d49b 100644
@@ -220,14 +220,14 @@ typedef enum {
 
 /* Non chip related options */
 /* This option skips the bbt scan during initialization. */
-#define NAND_SKIP_BBTSCAN	0x00020000
+#define NAND_SKIP_BBTSCAN	0x00010000
 /*
  * This option is defined if the board driver allocates its own buffers
  * (e.g. because it needs them DMA-coherent).
  */
-#define NAND_OWN_BUFFERS	0x00040000
+#define NAND_OWN_BUFFERS	0x00020000
 /* Chip may not exist, so silence any errors in scan */
-#define NAND_SCAN_SILENT_NODEV	0x00080000
+#define NAND_SCAN_SILENT_NODEV	0x00040000
 
 /* Options set by nand scan */
 /* Nand scan has allocated controller struct */

index 57d6a8d..c4eec22 100644
@@ -113,7 +113,11 @@ struct nand_bbt_descr {
 /* Do not store flash based bad block table in OOB area; store it in-band */
 #define NAND_BBT_NO_OOB		0x00040000
 
-/* The nand_bbt_descr was created dynamicaly and must be freed */
+/*
+ * Flag set by nand_create_default_bbt_descr(), marking that the nand_bbt_descr
+ * was allocated dynamicaly and must be freed in nand_release(). Has no meaning
+ * in nand_chip.bbt_options.
+ */
 #define NAND_BBT_DYNAMICSTRUCT	0x80000000
 
 /* The maximum number of blocks to scan for a bbt */