Skip to contentSkip to conversation

Misc fixes for floppy emulation

PATCH Superseded Hervé Poussineau 3 participants 16 messages Jan 8, 2012 – Jan 11, 2012

v1 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

cover Misc fixes for floppy emulation

Here are misc fixes done by VirtualBox team.
With these patches, floppy emulation is now good enough to run Xenix.

Hervé Poussineau (10):
fdc: take head count into account
fdc: set busy bit when starting a command
fdc: most control commands do not generate interrupts
fdc: emulate stepping 0
fdc: handle read-only floppies (abort early on write commands)
block: add a transfer rate for floppy types
fdc: check if media rate is correct before doing any transfer
fdc: add CCR (Configuration Control Register) write register
fdc: fix seek command, which shouldn't check tracks
fdc: DIR (Digital Input Register) should return status of current

    drive...
 block.c  |   74 +++++++++++++++++++++-------------------
 block.h  |   10 +++++-
 hw/fdc.c |  114 +++++++++++++++++++++++++++++++++++++++++++++----------------
 hw/pc.c  |    3 +-
 4 files changed, 134 insertions(+), 67 deletions(-)
Signature · 1 line
1.7.7.3
#1 lore raw

PATCH 1/10 fdc: take head count into account

---
 hw/fdc.c |   17 +++++++++++------
 1 files changed, 11 insertions(+), 6 deletions(-)
hw/fdc.c +11 -6
index 70aa5c7..c1898a6 100644
@@ -95,16 +95,19 @@ static void fd_init(FDrive *drv)
     drv->max_track = 0;
 }
 
+#define NUM_SIDES(drv) ((drv)->flags & FDISK_DBL_SIDES ? 2 : 1)
+
 static int fd_sector_calc(uint8_t head, uint8_t track, uint8_t sect,
-                          uint8_t last_sect)
+                          uint8_t last_sect, uint8_t num_sides)
 {
-    return (((track * 2) + head) * last_sect) + sect - 1;
+    return (((track * num_sides) + head) * last_sect) + sect - 1;
 }
 
 /* Returns current position, in sectors, for given drive */
 static int fd_sector(FDrive *drv)
 {
-    return fd_sector_calc(drv->head, drv->track, drv->sect, drv->last_sect);
+    return fd_sector_calc(drv->head, drv->track, drv->sect, drv->last_sect,
+                          NUM_SIDES(drv));
 }
 
 /* Seek to a new position:
@@ -135,7 +138,7 @@ static int fd_seek(FDrive *drv, uint8_t head, uint8_t track, uint8_t sect,
                        drv->max_track, drv->last_sect);
         return 3;
     }
-    sector = fd_sector_calc(head, track, sect, drv->last_sect);
+    sector = fd_sector_calc(head, track, sect, drv->last_sect, NUM_SIDES(drv));
     ret = 0;
     if (sector != fd_sector(drv)) {
 #if 0
@@ -1019,7 +1022,8 @@ static void fdctrl_start_transfer(FDCtrl *fdctrl, int direction)
     ks = fdctrl->fifo[4];
     FLOPPY_DPRINTF("Start transfer at %d %d %02x %02x (%d)\n",
                    GET_CUR_DRV(fdctrl), kh, kt, ks,
-                   fd_sector_calc(kh, kt, ks, cur_drv->last_sect));
+                   fd_sector_calc(kh, kt, ks, cur_drv->last_sect,
+                                  NUM_SIDES(cur_drv)));
     switch (fd_seek(cur_drv, kh, kt, ks, fdctrl->config & FD_CONFIG_EIS)) {
     case 2:
         /* sect too big */
@@ -1289,7 +1293,8 @@ static void fdctrl_format_sector(FDCtrl *fdctrl)
     ks = fdctrl->fifo[8];
     FLOPPY_DPRINTF("format sector at %d %d %02x %02x (%d)\n",
                    GET_CUR_DRV(fdctrl), kh, kt, ks,
-                   fd_sector_calc(kh, kt, ks, cur_drv->last_sect));
+                   fd_sector_calc(kh, kt, ks, cur_drv->last_sect,
+                                  NUM_SIDES(cur_drv)));
     switch (fd_seek(cur_drv, kh, kt, ks, fdctrl->config & FD_CONFIG_EIS)) {
     case 2:
         /* sect too big */
Signature · 1 line
1.7.7.3
#2 lore raw

PATCH 2/10 fdc: set busy bit when starting a command

In reply to Hervé Poussineau
---
 hw/fdc.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)
hw/fdc.c +1 -1
index c1898a6..1b9f303 100644
@@ -1446,7 +1446,6 @@ static void fdctrl_handle_readid(FDCtrl *fdctrl, int direction)
 {
     FDrive *cur_drv = get_cur_drv(fdctrl);
 
-    /* XXX: should set main status register to busy */
     cur_drv->head = (fdctrl->fifo[1] >> 2) & 1;
     qemu_mod_timer(fdctrl->result_timer,
                    qemu_get_clock_ns(vm_clock) + (get_ticks_per_sec() / 50));
@@ -1734,6 +1733,7 @@ static void fdctrl_write_data(FDCtrl *fdctrl, uint32_t value)
         pos = command_to_handler[value & 0xff];
         FLOPPY_DPRINTF("%s command\n", handlers[pos].name);
         fdctrl->data_len = handlers[pos].parameters + 1;
+        fdctrl->msr |= FD_MSR_CMDBUSY;
     }
 
     FLOPPY_DPRINTF("%s: %02x\n", __func__, value);
Signature · 1 line
1.7.7.3
#3 lore raw

PATCH 3/10 fdc: most control commands do not generate interrupts

In reply to Hervé Poussineau
---
 hw/fdc.c |   12 ++++++------
 1 files changed, 6 insertions(+), 6 deletions(-)
hw/fdc.c +6 -6
index 1b9f303..bedaeca 100644
@@ -1348,7 +1348,7 @@ static void fdctrl_handle_lock(FDCtrl *fdctrl, int direction)
 {
     fdctrl->lock = (fdctrl->fifo[0] & 0x80) ? 1 : 0;
     fdctrl->fifo[0] = fdctrl->lock << 4;
-    fdctrl_set_fifo(fdctrl, 1, fdctrl->lock);
+    fdctrl_set_fifo(fdctrl, 1, 0);
 }
 
 static void fdctrl_handle_dumpreg(FDCtrl *fdctrl, int direction)
@@ -1380,7 +1380,7 @@ static void fdctrl_handle_version(FDCtrl *fdctrl, int direction)
 {
     /* Controller's version */
     fdctrl->fifo[0] = fdctrl->version;
-    fdctrl_set_fifo(fdctrl, 1, 1);
+    fdctrl_set_fifo(fdctrl, 1, 0);
 }
 
 static void fdctrl_handle_partid(FDCtrl *fdctrl, int direction)
@@ -1439,7 +1439,7 @@ static void fdctrl_handle_save(FDCtrl *fdctrl, int direction)
     fdctrl->fifo[12] = fdctrl->pwrd;
     fdctrl->fifo[13] = 0;
     fdctrl->fifo[14] = 0;
-    fdctrl_set_fifo(fdctrl, 15, 1);
+    fdctrl_set_fifo(fdctrl, 15, 0);
 }
 
 static void fdctrl_handle_readid(FDCtrl *fdctrl, int direction)
@@ -1580,7 +1580,7 @@ static void fdctrl_handle_powerdown_mode(FDCtrl *fdctrl, int direction)
 {
     fdctrl->pwrd = fdctrl->fifo[1];
     fdctrl->fifo[0] = fdctrl->fifo[1];
-    fdctrl_set_fifo(fdctrl, 1, 1);
+    fdctrl_set_fifo(fdctrl, 1, 0);
 }
 
 static void fdctrl_handle_option(FDCtrl *fdctrl, int direction)
@@ -1599,7 +1599,7 @@ static void fdctrl_handle_drive_specification_command(FDCtrl *fdctrl, int direct
             fdctrl->fifo[0] = fdctrl->fifo[1];
             fdctrl->fifo[2] = 0;
             fdctrl->fifo[3] = 0;
-            fdctrl_set_fifo(fdctrl, 4, 1);
+            fdctrl_set_fifo(fdctrl, 4, 0);
         } else {
             fdctrl_reset_fifo(fdctrl);
         }
@@ -1607,7 +1607,7 @@ static void fdctrl_handle_drive_specification_command(FDCtrl *fdctrl, int direct
         /* ERROR */
         fdctrl->fifo[0] = 0x80 |
             (cur_drv->head << 2) | GET_CUR_DRV(fdctrl);
-        fdctrl_set_fifo(fdctrl, 1, 1);
+        fdctrl_set_fifo(fdctrl, 1, 0);
     }
 }
 
Signature · 1 line
1.7.7.3
#4 lore raw

PATCH 4/10 fdc: emulate stepping 0

In reply to Hervé Poussineau

Stepping 1 (S82078B) is not fully i82078 compatible, so better stick to initial revision

---
 hw/fdc.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)
hw/fdc.c +1 -1
index bedaeca..0e167f8 100644
@@ -1385,7 +1385,7 @@ static void fdctrl_handle_version(FDCtrl *fdctrl, int direction)
 
 static void fdctrl_handle_partid(FDCtrl *fdctrl, int direction)
 {
-    fdctrl->fifo[0] = 0x41; /* Stepping 1 */
+    fdctrl->fifo[0] = 0x01; /* Stepping 0 */
     fdctrl_set_fifo(fdctrl, 1, 0);
 }
 
Signature · 1 line
1.7.7.3
#5 lore raw

PATCH 5/10 fdc: handle read-only floppies (abort early on write commands)

In reply to Hervé Poussineau
---
 hw/fdc.c |   11 +++++++++++
 1 files changed, 11 insertions(+), 0 deletions(-)
hw/fdc.c +11 -0
index 0e167f8..078ff0c 100644
@@ -300,6 +300,7 @@ enum {
 };
 
 enum {
+    FD_SR1_NW       = 0x02, /* Not writable */
     FD_SR1_EC       = 0x80, /* End of cylinder */
 };
 
@@ -1179,6 +1180,16 @@ static int fdctrl_transfer_handler (void *opaque, int nchan,
             break;
         case FD_DIR_WRITE:
             /* WRITE commands */
+            if (cur_drv->ro) {
+                /* Handle readonly medium early, no need to do DMA, touch the
+                 * LED or attempt any writes. A real floppy doesn't attempt
+                 * to write to readonly media either. */
+                fdctrl_stop_transfer(fdctrl,
+                                     FD_SR0_ABNTERM | FD_SR0_SEEK, FD_SR1_NW,
+                                     0x00);
+                goto transfer_error;
+            }
+
             DMA_read_memory (nchan, fdctrl->fifo + rel_pos,
                              fdctrl->data_pos, len);
             if (bdrv_write(cur_drv->bs, fd_sector(cur_drv),
Signature · 1 line
1.7.7.3
#6 lore raw

PATCH 6/10 block: add a transfer rate for floppy types

In reply to Hervé Poussineau
---
 block.c  |   74 ++++++++++++++++++++++++++++++++-----------------------------
 block.h  |   10 +++++++-
 hw/fdc.c |    3 +-
 hw/pc.c  |    3 +-
 4 files changed, 52 insertions(+), 38 deletions(-)
block.c +39 -35
index 3f072f6..2c3fefb 100644
@@ -1884,58 +1884,60 @@ typedef struct FDFormat {
     uint8_t last_sect;
     uint8_t max_track;
     uint8_t max_head;
+    FDriveRate rate;
 } FDFormat;
 
 static const FDFormat fd_formats[] = {
     /* First entry is default format */
     /* 1.44 MB 3"1/2 floppy disks */
-    { FDRIVE_DRV_144, 18, 80, 1, },
-    { FDRIVE_DRV_144, 20, 80, 1, },
-    { FDRIVE_DRV_144, 21, 80, 1, },
-    { FDRIVE_DRV_144, 21, 82, 1, },
-    { FDRIVE_DRV_144, 21, 83, 1, },
-    { FDRIVE_DRV_144, 22, 80, 1, },
-    { FDRIVE_DRV_144, 23, 80, 1, },
-    { FDRIVE_DRV_144, 24, 80, 1, },
+    { FDRIVE_DRV_144, 18, 80, 1, FDRIVE_RATE_500K, },
+    { FDRIVE_DRV_144, 20, 80, 1, FDRIVE_RATE_500K, },
+    { FDRIVE_DRV_144, 21, 80, 1, FDRIVE_RATE_500K, },
+    { FDRIVE_DRV_144, 21, 82, 1, FDRIVE_RATE_500K, },
+    { FDRIVE_DRV_144, 21, 83, 1, FDRIVE_RATE_500K, },
+    { FDRIVE_DRV_144, 22, 80, 1, FDRIVE_RATE_500K, },
+    { FDRIVE_DRV_144, 23, 80, 1, FDRIVE_RATE_500K },
+    { FDRIVE_DRV_144, 24, 80, 1, FDRIVE_RATE_500K, },
     /* 2.88 MB 3"1/2 floppy disks */
-    { FDRIVE_DRV_288, 36, 80, 1, },
-    { FDRIVE_DRV_288, 39, 80, 1, },
-    { FDRIVE_DRV_288, 40, 80, 1, },
-    { FDRIVE_DRV_288, 44, 80, 1, },
-    { FDRIVE_DRV_288, 48, 80, 1, },
+    { FDRIVE_DRV_288, 36, 80, 1, FDRIVE_RATE_1M, },
+    { FDRIVE_DRV_288, 39, 80, 1, FDRIVE_RATE_1M, },
+    { FDRIVE_DRV_288, 40, 80, 1, FDRIVE_RATE_1M, },
+    { FDRIVE_DRV_288, 44, 80, 1, FDRIVE_RATE_1M, },
+    { FDRIVE_DRV_288, 48, 80, 1, FDRIVE_RATE_1M, },
     /* 720 kB 3"1/2 floppy disks */
-    { FDRIVE_DRV_144,  9, 80, 1, },
-    { FDRIVE_DRV_144, 10, 80, 1, },
-    { FDRIVE_DRV_144, 10, 82, 1, },
-    { FDRIVE_DRV_144, 10, 83, 1, },
-    { FDRIVE_DRV_144, 13, 80, 1, },
-    { FDRIVE_DRV_144, 14, 80, 1, },
+    { FDRIVE_DRV_144,  9, 80, 1, FDRIVE_RATE_250K, },
+    { FDRIVE_DRV_144, 10, 80, 1, FDRIVE_RATE_250K, },
+    { FDRIVE_DRV_144, 10, 82, 1, FDRIVE_RATE_250K, },
+    { FDRIVE_DRV_144, 10, 83, 1, FDRIVE_RATE_250K, },
+    { FDRIVE_DRV_144, 13, 80, 1, FDRIVE_RATE_250K, },
+    { FDRIVE_DRV_144, 14, 80, 1, FDRIVE_RATE_250K, },
     /* 1.2 MB 5"1/4 floppy disks */
-    { FDRIVE_DRV_120, 15, 80, 1, },
-    { FDRIVE_DRV_120, 18, 80, 1, },
-    { FDRIVE_DRV_120, 18, 82, 1, },
-    { FDRIVE_DRV_120, 18, 83, 1, },
-    { FDRIVE_DRV_120, 20, 80, 1, },
+    { FDRIVE_DRV_120, 15, 80, 1, FDRIVE_RATE_500K, },
+    { FDRIVE_DRV_120, 18, 80, 1, FDRIVE_RATE_500K, },
+    { FDRIVE_DRV_120, 18, 82, 1, FDRIVE_RATE_500K, },
+    { FDRIVE_DRV_120, 18, 83, 1, FDRIVE_RATE_500K, },
+    { FDRIVE_DRV_120, 20, 80, 1, FDRIVE_RATE_500K, },
     /* 720 kB 5"1/4 floppy disks */
-    { FDRIVE_DRV_120,  9, 80, 1, },
-    { FDRIVE_DRV_120, 11, 80, 1, },
+    { FDRIVE_DRV_120,  9, 80, 1, FDRIVE_RATE_250K, },
+    { FDRIVE_DRV_120, 11, 80, 1, FDRIVE_RATE_250K, },
     /* 360 kB 5"1/4 floppy disks */
-    { FDRIVE_DRV_120,  9, 40, 1, },
-    { FDRIVE_DRV_120,  9, 40, 0, },
-    { FDRIVE_DRV_120, 10, 41, 1, },
-    { FDRIVE_DRV_120, 10, 42, 1, },
+    { FDRIVE_DRV_120,  9, 40, 1, FDRIVE_RATE_300K, },
+    { FDRIVE_DRV_120,  9, 40, 0, FDRIVE_RATE_300K, },
+    { FDRIVE_DRV_120, 10, 41, 1, FDRIVE_RATE_300K, },
+    { FDRIVE_DRV_120, 10, 42, 1, FDRIVE_RATE_300K, },
     /* 320 kB 5"1/4 floppy disks */
-    { FDRIVE_DRV_120,  8, 40, 1, },
-    { FDRIVE_DRV_120,  8, 40, 0, },
+    { FDRIVE_DRV_120,  8, 40, 1, FDRIVE_RATE_250K, },
+    { FDRIVE_DRV_120,  8, 40, 0, FDRIVE_RATE_250K, },
     /* 360 kB must match 5"1/4 better than 3"1/2... */
-    { FDRIVE_DRV_144,  9, 80, 0, },
+    { FDRIVE_DRV_144,  9, 80, 0, FDRIVE_RATE_250K, },
     /* end */
-    { FDRIVE_DRV_NONE, -1, -1, 0, },
+    { FDRIVE_DRV_NONE, -1, -1, 0, 0, },
 };
 
 void bdrv_get_floppy_geometry_hint(BlockDriverState *bs, int *nb_heads,
                                    int *max_track, int *last_sect,
-                                   FDriveType drive_in, FDriveType *drive)
+                                   FDriveType drive_in, FDriveType *drive,
+                                   FDriveRate *rate)
 {
     const FDFormat *parse;
     uint64_t nb_sectors, size;
@@ -1944,6 +1946,7 @@ void bdrv_get_floppy_geometry_hint(BlockDriverState *bs, int *nb_heads,
     bdrv_get_geometry_hint(bs, nb_heads, max_track, last_sect);
     if (*nb_heads != 0 && *max_track != 0 && *last_sect != 0) {
         /* User defined disk */
+        *rate = FDRIVE_RATE_500K;
     } else {
         bdrv_get_geometry(bs, &nb_sectors);
         match = -1;
@@ -1978,6 +1981,7 @@ void bdrv_get_floppy_geometry_hint(BlockDriverState *bs, int *nb_heads,
         *max_track = parse->max_track;
         *last_sect = parse->last_sect;
         *drive = parse->drive;
+        *rate = parse->rate;
     }
 }
 
block.h +9 -1
index 3bd4398..27cc966 100644
@@ -240,9 +240,17 @@ typedef enum FDriveType {
     FDRIVE_DRV_NONE = 0x03,   /* No drive connected     */
 } FDriveType;
 
+typedef enum FDriveRate {
+    FDRIVE_RATE_500K = 0x00,  /* 500 Kbps */
+    FDRIVE_RATE_300K = 0x01,  /* 300 Kbps */
+    FDRIVE_RATE_250K = 0x02,  /* 250 Kbps */
+    FDRIVE_RATE_1M   = 0x03,  /*   1 Mbps */
+} FDriveRate;
+
 void bdrv_get_floppy_geometry_hint(BlockDriverState *bs, int *nb_heads,
                                    int *max_track, int *last_sect,
-                                   FDriveType drive_in, FDriveType *drive);
+                                   FDriveType drive_in, FDriveType *drive,
+                                   FDriveRate *rate);
 int bdrv_get_translation_hint(BlockDriverState *bs);
 void bdrv_set_on_error(BlockDriverState *bs, BlockErrorAction on_read_error,
                        BlockErrorAction on_write_error);
hw/fdc.c +2 -1
index 078ff0c..aec1e5e 100644
@@ -172,12 +172,13 @@ static void fd_revalidate(FDrive *drv)
 {
     int nb_heads, max_track, last_sect, ro;
     FDriveType drive;
+    FDriveRate rate;
 
     FLOPPY_DPRINTF("revalidate\n");
     if (drv->bs != NULL && bdrv_is_inserted(drv->bs)) {
         ro = bdrv_is_read_only(drv->bs);
         bdrv_get_floppy_geometry_hint(drv->bs, &nb_heads, &max_track,
-                                      &last_sect, drv->drive, &drive);
+                                      &last_sect, drv->drive, &drive, &rate);
         if (nb_heads != 0 && max_track != 0 && last_sect != 0) {
             FLOPPY_DPRINTF("User defined disk (%d %d %d)",
                            nb_heads - 1, max_track, last_sect);
hw/pc.c +2 -1
index f51afa8..6e0c3c1 100644
@@ -336,6 +336,7 @@ void pc_cmos_init(ram_addr_t ram_size, ram_addr_t above_4g_mem_size,
 {
     int val, nb, nb_heads, max_track, last_sect, i;
     FDriveType fd_type[2] = { FDRIVE_DRV_NONE, FDRIVE_DRV_NONE };
+    FDriveRate rate;
     BlockDriverState *fd[MAX_FD];
     static pc_cmos_init_late_arg arg;
 
@@ -384,7 +385,7 @@ void pc_cmos_init(ram_addr_t ram_size, ram_addr_t above_4g_mem_size,
             if (fd[i] && bdrv_is_inserted(fd[i])) {
                 bdrv_get_floppy_geometry_hint(fd[i], &nb_heads, &max_track,
                                               &last_sect, FDRIVE_DRV_NONE,
-                                              &fd_type[i]);
+                                              &fd_type[i], &rate);
             }
         }
     }
Signature · 1 line
1.7.7.3
#7 lore raw

PATCH 7/10 fdc: check if media rate is correct before doing any transfer

In reply to Hervé Poussineau
---
 hw/fdc.c |   24 +++++++++++++++++++++++-
 1 files changed, 23 insertions(+), 1 deletions(-)
hw/fdc.c +23 -1
index aec1e5e..ddfa91f 100644
@@ -83,6 +83,7 @@ typedef struct FDrive {
     uint16_t bps;             /* Bytes per sector       */
     uint8_t ro;               /* Is read-only           */
     uint8_t media_changed;    /* Is media changed       */
+    uint8_t media_rate;       /* Data rate of medium    */
 } FDrive;
 
 static void fd_init(FDrive *drv)
@@ -195,6 +196,7 @@ static void fd_revalidate(FDrive *drv)
         drv->last_sect = last_sect;
         drv->ro = ro;
         drv->drive = drive;
+        drv->media_rate = rate;
     } else {
         FLOPPY_DPRINTF("No disk in drive\n");
         drv->last_sect = 0;
@@ -301,6 +303,7 @@ enum {
 };
 
 enum {
+    FD_SR1_MA       = 0x01, /* Missing address mark */
     FD_SR1_NW       = 0x02, /* Not writable */
     FD_SR1_EC       = 0x80, /* End of cylinder */
 };
@@ -1055,6 +1058,18 @@ static void fdctrl_start_transfer(FDCtrl *fdctrl, int direction)
         break;
     }
 
+    /* Check the data rate. If the programmed data rate does not match
+     * the currently inserted medium, the operation has to fail. */
+    if ((fdctrl->dsr & FD_DSR_DRATEMASK) != cur_drv->media_rate) {
+        FLOPPY_DPRINTF("data rate mismatch (fdc=%d, media=%d)\n",
+                       fdctrl->dsr & FD_DSR_DRATEMASK, cur_drv->media_rate);
+        fdctrl_stop_transfer(fdctrl, FD_SR0_ABNTERM, FD_SR1_MA, 0x00);
+        fdctrl->fifo[3] = kt;
+        fdctrl->fifo[4] = kh;
+        fdctrl->fifo[5] = ks;
+        return;
+    }
+
     /* Set the FIFO state */
     fdctrl->data_dir = direction;
     fdctrl->data_pos = 0;
@@ -1777,7 +1792,14 @@ static void fdctrl_result_timer(void *opaque)
     if (cur_drv->last_sect != 0) {
         cur_drv->sect = (cur_drv->sect % cur_drv->last_sect) + 1;
     }
-    fdctrl_stop_transfer(fdctrl, 0x00, 0x00, 0x00);
+    /* READ_ID can't automatically succeed! */
+    if ((fdctrl->dsr & FD_DSR_DRATEMASK) != cur_drv->media_rate) {
+        FLOPPY_DPRINTF("read id rate mismatch (fdc=%d, media=%d)\n",
+                       fdctrl->dsr & FD_DSR_DRATEMASK, cur_drv->media_rate);
+        fdctrl_stop_transfer(fdctrl, FD_SR0_ABNTERM, FD_SR1_MA, 0x00);
+    } else {
+        fdctrl_stop_transfer(fdctrl, 0x00, 0x00, 0x00);
+    }
 }
 
 static void fdctrl_change_cb(void *opaque, bool load)
Signature · 1 line
1.7.7.3
#8 lore raw

Re: [Qemu-devel] [PATCH 07/10] fdc: check if media rate is correct before doing any transfer

Am 08.01.2012 21:27, schrieb Hervé Poussineau:

Quoted 11 lines
---
 hw/fdc.c |   24 +++++++++++++++++++++++-
 1 files changed, 23 insertions(+), 1 deletions(-)
hw/fdc.c +0 -0
index aec1e5e..ddfa91f 100644

hw/fdc.c typedef struct FDrive { · line 86

Quoted 4 lines
hw/fdc.c +1 -0
@@ -83,6 +83,7 @@ typedef struct FDrive {
     uint16_t bps;             /* Bytes per sector       */
     uint8_t ro;               /* Is read-only           */
     uint8_t media_changed;    /* Is media changed       */
+    uint8_t media_rate;       /* Data rate of medium    */

No VMState needed for this?

Andreas

Signature · 2 lines
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
#9 lore raw

PATCH 8/10 fdc: add CCR (Configuration Control Register) write register

In reply to Hervé Poussineau
---
 hw/fdc.c |   21 +++++++++++++++++++++
 1 files changed, 21 insertions(+), 0 deletions(-)
hw/fdc.c +21 -0
index ddfa91f..67cd14f 100644
@@ -227,6 +227,7 @@ static void fdctrl_write_rate(FDCtrl *fdctrl, uint32_t value);
 static uint32_t fdctrl_read_data(FDCtrl *fdctrl);
 static void fdctrl_write_data(FDCtrl *fdctrl, uint32_t value);
 static uint32_t fdctrl_read_dir(FDCtrl *fdctrl);
+static void fdctrl_write_ccr(FDCtrl *fdctrl, uint32_t value);
 
 enum {
     FD_DIR_WRITE   = 0,
@@ -251,6 +252,7 @@ enum {
     FD_REG_DSR = 0x04,
     FD_REG_FIFO = 0x05,
     FD_REG_DIR = 0x07,
+    FD_REG_CCR = 0x07,
 };
 
 enum {
@@ -495,6 +497,8 @@ static void fdctrl_write (void *opaque, uint32_t reg, uint32_t value)
     case FD_REG_FIFO:
         fdctrl_write_data(fdctrl, value);
         break;
+    case FD_REG_CCR:
+        fdctrl_write_ccr(fdctrl, value);
     default:
         break;
     }
@@ -885,6 +889,23 @@ static void fdctrl_write_rate(FDCtrl *fdctrl, uint32_t value)
     fdctrl->dsr = value;
 }
 
+/* Configuration control register: 0x07 (write) */
+static void fdctrl_write_ccr(FDCtrl *fdctrl, uint32_t value)
+{
+    /* Reset mode */
+    if (!(fdctrl->dor & FD_DOR_nRESET)) {
+        FLOPPY_DPRINTF("Floppy controller in RESET state !\n");
+        return;
+    }
+    FLOPPY_DPRINTF("configuration control register set to 0x%02x\n", value);
+
+    /* Only the rate selection bits used in AT mode, and we
+     * store those in the DSR.
+     */
+    fdctrl->dsr = (fdctrl->dsr & ~FD_DSR_DRATEMASK) |
+                  (value & FD_DSR_DRATEMASK);
+}
+
 static int fdctrl_media_changed(FDrive *drv)
 {
     int ret;
Signature · 1 line
1.7.7.3
#10 lore raw

Re: [Qemu-devel] [PATCH 08/10] fdc: add CCR (Configuration Control Register) write register

Quoted 49 lines · Hervé Poussineau
---
  hw/fdc.c |   21 +++++++++++++++++++++
  1 files changed, 21 insertions(+), 0 deletions(-)
hw/fdc.c +14 -0
index ddfa91f..67cd14f 100644
@@ -227,6 +227,7 @@ static void fdctrl_write_rate(FDCtrl *fdctrl, uint32_t value);
  static uint32_t fdctrl_read_data(FDCtrl *fdctrl);
  static void fdctrl_write_data(FDCtrl *fdctrl, uint32_t value);
  static uint32_t fdctrl_read_dir(FDCtrl *fdctrl);
+static void fdctrl_write_ccr(FDCtrl *fdctrl, uint32_t value);
 
  enum {
      FD_DIR_WRITE   = 0,
@@ -251,6 +252,7 @@ enum {
      FD_REG_DSR = 0x04,
      FD_REG_FIFO = 0x05,
      FD_REG_DIR = 0x07,
+    FD_REG_CCR = 0x07,
  };
 
  enum {
@@ -495,6 +497,8 @@ static void fdctrl_write (void *opaque, uint32_t reg, uint32_t value)
      case FD_REG_FIFO:
          fdctrl_write_data(fdctrl, value);
          break;
+    case FD_REG_CCR:
+        fdctrl_write_ccr(fdctrl, value);
      default:
          break;
      }
@@ -885,6 +889,23 @@ static void fdctrl_write_rate(FDCtrl *fdctrl, uint32_t value)
      fdctrl->dsr = value;
  }
 
+/* Configuration control register: 0x07 (write) */
+static void fdctrl_write_ccr(FDCtrl *fdctrl, uint32_t value)
+{
+    /* Reset mode */
+    if (!(fdctrl->dor&  FD_DOR_nRESET)) {
+        FLOPPY_DPRINTF("Floppy controller in RESET state !\n");
+        return;
+    }
+    FLOPPY_DPRINTF("configuration control register set to 0x%02x\n", value);
+

hw/fdc.c static void fdctrl_write_rate(FDCtrl *fdctrl, uint32_t value) · line 911

Quoted 10 lines
hw/fdc.c +7 -0
+    /* Only the rate selection bits used in AT mode, and we
+     * store those in the DSR.
+     */
+    fdctrl->dsr = (fdctrl->dsr&  ~FD_DSR_DRATEMASK) |
+                  (value&  FD_DSR_DRATEMASK);
+}
+
  static int fdctrl_media_changed(FDrive *drv)
  {
      int ret;

This should go before patch 7, shouldn't it?

Paolo

#11 lore raw

Re: [Qemu-devel] [PATCH 08/10] fdc: add CCR (Configuration Control Register) write register

On 01/09/2012 09:09 AM, Paolo Bonzini wrote:

This should go before patch 7, shouldn't it?

Yes, I can exchange patches 7 and 8.

However, in this order, only floppies other than 1.44 Mb may fail (depends if DSR or CCR register is used to write required rate).

I would like to have some more review before respinning (if required...)

Hervé

#12 lore raw

Re: [Qemu-devel] [PATCH 08/10] fdc: add CCR (Configuration Control Register) write register

In reply to Hervé Poussineau

Am 08.01.2012 21:27, schrieb Hervé Poussineau:

Quoted 19 lines
---
 hw/fdc.c |   21 +++++++++++++++++++++
 1 files changed, 21 insertions(+), 0 deletions(-)
hw/fdc.c +1 -0
index ddfa91f..67cd14f 100644
@@ -227,6 +227,7 @@ static void fdctrl_write_rate(FDCtrl *fdctrl, uint32_t value);
 static uint32_t fdctrl_read_data(FDCtrl *fdctrl);
 static void fdctrl_write_data(FDCtrl *fdctrl, uint32_t value);
 static uint32_t fdctrl_read_dir(FDCtrl *fdctrl);
+static void fdctrl_write_ccr(FDCtrl *fdctrl, uint32_t value);
 
 enum {
     FD_DIR_WRITE   = 0,

hw/fdc.c enum { · line 255

Quoted 4 lines
hw/fdc.c +1 -0
@@ -251,6 +252,7 @@ enum {
     FD_REG_DSR = 0x04,
     FD_REG_FIFO = 0x05,
     FD_REG_DIR = 0x07,
+    FD_REG_CCR = 0x07,

I'm not familiar with FDCs, so this reads weird: Do DIR and CCR share the same address, with DIR being read-only and CCR write-only? If so, an explanatory sentence in the commit message would be nice. (dito for most other patches in the series)

hw/fdc.c static void fdctrl_write (void *opaque, uint32_t reg, uint32_t value) · line 501

Quoted 9 lines
hw/fdc.c +2 -0
 };
 
 enum {
@@ -495,6 +497,8 @@ static void fdctrl_write (void *opaque, uint32_t reg, uint32_t value)
     case FD_REG_FIFO:
         fdctrl_write_data(fdctrl, value);
         break;
+    case FD_REG_CCR:
+        fdctrl_write_ccr(fdctrl, value);

break; please, to avoid future errors or complaints by static analysis tools.

Andreas

Quoted 3 lines
hw/fdc.c +0 -0
     default:
         break;
     }
Signature · 2 lines
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
#13 lore raw

PATCH 9/10 fdc: fix seek command, which shouldn't check tracks

In reply to Hervé Poussineau
---
 hw/fdc.c |   13 ++++++-------
 1 files changed, 6 insertions(+), 7 deletions(-)
hw/fdc.c +6 -7
index 67cd14f..7af0f7e 100644
@@ -1597,13 +1597,12 @@ static void fdctrl_handle_seek(FDCtrl *fdctrl, int direction)
     SET_CUR_DRV(fdctrl, fdctrl->fifo[1] & FD_DOR_SELMASK);
     cur_drv = get_cur_drv(fdctrl);
     fdctrl_reset_fifo(fdctrl);
-    if (fdctrl->fifo[2] > cur_drv->max_track) {
-        fdctrl_raise_irq(fdctrl, FD_SR0_ABNTERM | FD_SR0_SEEK);
-    } else {
-        cur_drv->track = fdctrl->fifo[2];
-        /* Raise Interrupt */
-        fdctrl_raise_irq(fdctrl, FD_SR0_SEEK);
-    }
+    /* The seek command just sends step pulses to the drive and doesn't care if
+     * there is a medium inserted of if it's banging the head against the drive.
+     */
+    cur_drv->track = fdctrl->fifo[2];
+    /* Raise Interrupt */
+    fdctrl_raise_irq(fdctrl, FD_SR0_SEEK);
 }
 
 static void fdctrl_handle_perpendicular_mode(FDCtrl *fdctrl, int direction)
Signature · 1 line
1.7.7.3
#14 lore raw

PATCH 10/10 fdc: DIR (Digital Input Register) should return status of current drive...

In reply to Hervé Poussineau
---
 hw/fdc.c |    9 ++-------
 1 files changed, 2 insertions(+), 7 deletions(-)
hw/fdc.c +2 -7
index 7af0f7e..a23fb1e 100644
@@ -215,6 +215,7 @@ static void fdctrl_reset_fifo(FDCtrl *fdctrl);
 static int fdctrl_transfer_handler (void *opaque, int nchan,
                                     int dma_pos, int dma_len);
 static void fdctrl_raise_irq(FDCtrl *fdctrl, uint8_t status0);
+static FDrive *get_cur_drv(FDCtrl *fdctrl);
 
 static uint32_t fdctrl_read_statusA(FDCtrl *fdctrl);
 static uint32_t fdctrl_read_statusB(FDCtrl *fdctrl);
@@ -932,13 +933,7 @@ static uint32_t fdctrl_read_dir(FDCtrl *fdctrl)
 {
     uint32_t retval = 0;
 
-    if (fdctrl_media_changed(drv0(fdctrl))
-     || fdctrl_media_changed(drv1(fdctrl))
-#if MAX_FD == 4
-     || fdctrl_media_changed(drv2(fdctrl))
-     || fdctrl_media_changed(drv3(fdctrl))
-#endif
-        )
+    if (fdctrl_media_changed(get_cur_drv(fdctrl)))
         retval |= FD_DIR_DSKCHG;
     if (retval != 0) {
         FLOPPY_DPRINTF("Floppy digital input register: 0x%02x\n", retval);
Signature · 1 line
1.7.7.3
#15 lore raw

Re: [Qemu-devel] [PATCH 10/10] fdc: DIR (Digital Input Register) should return status of current drive...

Am 08.01.2012 21:27, schrieb Hervé Poussineau:

Quoted 14 lines
---
 hw/fdc.c |    9 ++-------
 1 files changed, 2 insertions(+), 7 deletions(-)
hw/fdc.c +0 -0
index 7af0f7e..a23fb1e 100644
@@ -932,13 +933,7 @@ static uint32_t fdctrl_read_dir(FDCtrl *fdctrl)
 {
     uint32_t retval = 0;

hw/fdc.c static uint32_t fdctrl_read_dir(FDCtrl *fdctrl) · line 937

Quoted 10 lines
hw/fdc.c +1 -7
 
-    if (fdctrl_media_changed(drv0(fdctrl))
-     || fdctrl_media_changed(drv1(fdctrl))
-#if MAX_FD == 4
-     || fdctrl_media_changed(drv2(fdctrl))
-     || fdctrl_media_changed(drv3(fdctrl))
-#endif
-        )
+    if (fdctrl_media_changed(get_cur_drv(fdctrl)))
         retval |= FD_DIR_DSKCHG;

Braces :) (Most famous review comment...)

Andreas

Quoted 2 lines
hw/fdc.c +0 -0
     if (retval != 0) {
         FLOPPY_DPRINTF("Floppy digital input register: 0x%02x\n", retval);
Signature · 2 lines
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg