Skip to contentSkip to conversation

MFD: add ADC support to DA9052/53 MFD core v2

PATCH In review Ashish Jangam 4 participants 4 messages Jan 13, 2012 – Feb 20, 2012

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 MFD: add ADC support to DA9052/53 MFD core v2

This patch add ADC support for DA9052/53 MFD core so that its dependent components like Battery & HWMON can read required values from ADC channel.

---
Changes since v1:
- Remove list handling as there is single active request at any time

---
 drivers/mfd/da9052-core.c         |  133 +++++++++++++++++++++++++++++++++++++
 include/linux/mfd/da9052/da9052.h |   17 +++++
 2 files changed, 150 insertions(+), 0 deletions(-)
drivers/mfd/da9052-core.c +133 -0
index 5ddde2a..99e2262 100644
@@ -319,6 +319,130 @@ static bool da9052_reg_volatile(struct device *dev, unsigned int reg)
 	}
 }
 
+/*
+ * TBAT look-up table is computed from the R90 reg (8 bit register)
+ * reading as below. The battery temperature is in milliCentigrade
+ * TBAT = (1/(t1+1/298) - 273) * 1000 mC
+ * where t1 = (1/B)* ln(( ADCval * 2.5)/(R25*ITBAT*255))
+ * Default values are R25 = 10e3, B = 3380, ITBAT = 50e-6
+ * Example:
+ * R25=10E3, B=3380, ITBAT=50e-6, ADCVAL=62d calculates
+ * TBAT = 20015 mili degrees Centrigrade
+ *
+*/
+static const int32_t tbat_lookup[255] = {
+	183258, 144221, 124334, 111336, 101826, 94397, 88343, 83257,
+	78889, 75071, 71688, 68656, 65914, 63414, 61120, 59001,
+	570366, 55204, 53490, 51881, 50364, 48931, 47574, 46285,
+	45059, 43889, 42772, 41703, 40678, 39694, 38748, 37838,
+	36961, 36115, 35297, 34507, 33743, 33002, 32284, 31588,
+	30911, 30254, 29615, 28994, 28389, 27799, 27225, 26664,
+	26117, 25584, 25062, 24553, 24054, 23567, 23091, 22624,
+	22167, 21719, 21281, 20851, 20429, 20015, 19610, 19211,
+	18820, 18436, 18058, 17688, 17323, 16965, 16612, 16266,
+	15925, 15589, 15259, 14933, 14613, 14298, 13987, 13681,
+	13379, 13082, 12788, 12499, 12214, 11933, 11655, 11382,
+	11112, 10845, 10582, 10322, 10066, 9812, 9562, 9315,
+	9071, 8830, 8591, 8356, 8123, 7893, 7665, 7440,
+	7218, 6998, 6780, 6565, 6352, 6141, 5933, 5726,
+	5522, 5320, 5120, 4922, 4726, 4532, 4340, 4149,
+	3961, 3774, 3589, 3406, 3225, 3045, 2867, 2690,
+	2516, 2342, 2170, 2000, 1831, 1664, 1498, 1334,
+	1171, 1009, 849, 690, 532, 376, 221, 67,
+	-84, -236, -386, -535, -683, -830, -975, -1119,
+	-1263, -1405, -1546, -1686, -1825, -1964, -2101, -2237,
+	-2372, -2506, -2639, -2771, -2902, -3033, -3162, -3291,
+	-3418, -3545, -3671, -3796, -3920, -4044, -4166, -4288,
+	-4409, -4529, -4649, -4767, -4885, -5002, -5119, -5235,
+	-5349, -5464, -5577, -5690, -5802, -5913, -6024, -6134,
+	-6244, -6352, -6461, -6568, -6675, -6781, -6887, -6992,
+	-7096, -7200, -7303, -7406, -7508, -7609, -7710, -7810,
+	-7910, -8009, -8108, -8206, -8304, -8401, -8497, -8593,
+	-8689, -8784, -8878, -8972, -9066, -9159, -9251, -9343,
+	-9435, -9526, -9617, -9707, -9796, -9886, -9975, -10063,
+	-10151, -10238, -10325, -10412, -10839, -10923, -11007, -11090,
+	-11173, -11256, -11338, -11420, -11501, -11583, -11663, -11744,
+	-11823, -11903, -11982
+};
+
+static const u8 chan_mux[DA9052_ADC_VBBAT + 1] = {
+	[DA9052_ADC_VDDOUT]	= DA9052_ADC_MAN_MUXSEL_VDDOUT,
+	[DA9052_ADC_ICH]	= DA9052_ADC_MAN_MUXSEL_ICH,
+	[DA9052_ADC_TBAT]	= DA9052_ADC_MAN_MUXSEL_TBAT,
+	[DA9052_ADC_VBAT]	= DA9052_ADC_MAN_MUXSEL_VBAT,
+	[DA9052_ADC_IN4]	= DA9052_ADC_MAN_MUXSEL_AD4,
+	[DA9052_ADC_IN5]	= DA9052_ADC_MAN_MUXSEL_AD5,
+	[DA9052_ADC_IN6]	= DA9052_ADC_MAN_MUXSEL_AD6,
+	[DA9052_ADC_VBBAT]	= DA9052_ADC_MAN_MUXSEL_VBBAT
+};
+
+struct completion done;
+
+int da9052_adc_manual_read(struct da9052 *da9052, unsigned char channel)
+{
+	int ret;
+	unsigned short calc_data;
+	unsigned short data;
+	unsigned char mux_sel;
+
+	if (channel > DA9052_ADC_VBBAT)
+		return -EINVAL;
+
+	mutex_lock(&da9052->auxadc_lock);
+
+	/* Channel gets activated on enabling the Conversion bit */
+	mux_sel = chan_mux[channel] | DA9052_ADC_MAN_MAN_CONV;
+
+	ret = da9052_reg_write(da9052, DA9052_ADC_MAN_REG, mux_sel);
+	if (ret < 0)
+		goto err;
+
+	/* Wait for an interrupt */
+	wait_for_completion_timeout(&done, msecs_to_jiffies(500));
+
+	ret = da9052_reg_read(da9052, DA9052_ADC_RES_H_REG);
+	if (ret < 0)
+		goto err;
+
+	calc_data = (unsigned short)ret;
+	data = calc_data << 2;
+
+	ret = da9052_reg_read(da9052, DA9052_ADC_RES_L_REG);
+	if (ret < 0)
+		goto err;
+
+	calc_data = (unsigned short)(ret & DA9052_ADC_RES_LSB);
+	data |= calc_data;
+
+	ret = data;
+
+err:
+	mutex_unlock(&da9052->auxadc_lock);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(da9052_adc_manual_read);
+
+static irqreturn_t da9052_auxadc_irq(int irq, void *irq_data)
+{
+	complete(&done);
+
+	return IRQ_HANDLED;
+}
+
+int da9052_adc_read_temp(struct da9052 *da9052)
+{
+	int tbat;
+
+	tbat = da9052_reg_read(da9052, DA9052_TBAT_RES_REG);
+
+	if (tbat < 0)
+		return tbat;
+
+	/* ARRAY_SIZE check is not needed since TBAT is a 8-bit register */
+	return tbat_lookup[tbat - 1];
+}
+EXPORT_SYMBOL_GPL(da9052_adc_read_temp);
+
 static struct resource da9052_rtc_resource = {
 	.name = "ALM",
 	.start = DA9052_IRQ_ALARM,
@@ -648,6 +772,8 @@ int __devinit da9052_device_init(struct da9052 *da9052, u8 chip_id)
 	int ret;
 
 	mutex_init(&da9052->io_lock);
+	mutex_init(&da9052->auxadc_lock);
+	init_completion(&done);
 
 	if (pdata && pdata->init != NULL)
 		pdata->init(da9052);
@@ -669,6 +795,13 @@ int __devinit da9052_device_init(struct da9052 *da9052, u8 chip_id)
 	desc = irq_to_desc(da9052->chip_irq);
 	da9052->irq_base = regmap_irq_chip_get_base(desc->action->dev_id);
 
+	ret = request_threaded_irq(da9052->irq_base + DA9052_IRQ_ADC_EOM,
+				   NULL, da9052_auxadc_irq,
+				   IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+				   "adc irq", NULL);
+	if (ret != 0)
+		dev_err(da9052->dev, "DA9052 ADC IRQ failed ret=%d\n", ret);
+
 	ret = mfd_add_devices(da9052->dev, -1, da9052_subdev_info,
 			      ARRAY_SIZE(da9052_subdev_info), NULL, 0);
 	if (ret)
include/linux/mfd/da9052/da9052.h +17 -0
index 5702d1b..04d90b7 100644
@@ -33,6 +33,18 @@
 
 #include <linux/mfd/da9052/reg.h>
 
+/* HWMON Channel Definations */
+#define DA9052_ADC_VDDOUT	0
+#define DA9052_ADC_ICH		1
+#define DA9052_ADC_TBAT	2
+#define DA9052_ADC_VBAT	3
+#define DA9052_ADC_IN4		4
+#define DA9052_ADC_IN5		5
+#define DA9052_ADC_IN6		6
+#define DA9052_ADC_TSI		7
+#define DA9052_ADC_TJUNC	8
+#define DA9052_ADC_VBBAT	9
+
 #define DA9052_IRQ_DCIN	0
 #define DA9052_IRQ_VBUS	1
 #define DA9052_IRQ_DCINREM	2
@@ -77,6 +89,7 @@ struct da9052_pdata;
 
 struct da9052 {
 	struct mutex io_lock;
+	struct mutex auxadc_lock;
 
 	struct device *dev;
 	struct regmap *regmap;
@@ -87,6 +100,10 @@ struct da9052 {
 	int chip_irq;
 };
 
+/* ADC API */
+int da9052_adc_manual_read(struct da9052 *da9052, unsigned char channel);
+int da9052_adc_read_temp(struct da9052 *da9052);
+
 /* Device I/O API */
 static inline int da9052_reg_read(struct da9052 *da9052, unsigned char reg)
 {
#1 lore raw

Hi Ashish,

Quoted 1 line · Ashish Jangam

+struct completion done;

This shouldn't be a global variable, but a struct da9052 one instead.

Cheers,
Samuel.

Signature · 2 lines
Intel Open Source Technology Centre
http://oss.intel.com/
#2 lore raw
Quoted 3 lines · Samuel Ortiz
Quoted 1 line · Ashish Jangam

+struct completion done;

This shouldn't be a global variable, but a struct da9052 one instead.

Right. Since this thread has showed up in my inbox again, I've also taken a look at the patch now and noticed another thing:

Quoted 4 lines

drivers/mfd/da9052-core.c int __devinit da9052_device_init(struct da9052 *da9052, u8 chip_id) · line 801

Quoted 4 lines
drivers/mfd/da9052-core.c +4 -0
+       ret = request_threaded_irq(da9052->irq_base + DA9052_IRQ_ADC_EOM,
+                                  NULL, da9052_auxadc_irq,
+                                  IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+                                  "adc irq", NULL);

First of all, to clarify: The last argument to this function needs to be the pointer to da9052 so that it is available in the irq handler function.

Also, I would recommend using request_irq instead of request_threaded_irq here because the function only has a single "complete()" call in it, just like a threaded IRQ handler has. There is no point going through another thread just to wake up the one that is blocked.

Arnd

#3 lore raw
Quoted 4 lines · Arnd Bergmann

Also, I would recommend using request_irq instead of request_threaded_irq here because the function only has a single "complete()" call in it, just like a threaded IRQ handler has. There is no point going through another thread just to wake up the one that is blocked.

Actually in this case that won't work as the interrupt is generated by the chip interrupt controller and as the chip is I2C/SPI controlled it is itself threaded and can only generate threaded interrupts as genirq can't get back into hard interrupt context.

As a result of this restriction when an interrupt handler doesn't care what context it runs in it's better to use request_any_context_irq(). This will do a normal IRQ when it can but will bind successfully to a threaded IRQ if that's what's provided.