m68knommu: clean up init code in ColdFire 523x startup
PATCH 1/3 m68knommu: clean up init code in ColdFire 523x startup
From: Greg Ungerer <[email protected]>
We can move the QSPI init call to the more general config_BSP() code on the 523x platorm setup code. Then we can remove the initcall code all together.
We can also remove the un-needed include of mcfuart.h while we are cleaning up here too.
Also I noticed that we are not calling the fec_init() code here, and we should be doing that. Put that back in too.
--- arch/m68k/platform/523x/config.c | 11 +---------- 1 files changed, 1 insertions(+), 10 deletions(-)
arch/m68k/platform/523x/config.c +1 -10
@@ -19,7 +19,6 @@#include <asm/machdep.h> #include <asm/coldfire.h> #include <asm/mcfsim.h> -#include <asm/mcfuart.h> /***************************************************************************/
@@ -66,18 +65,10 @@ static void m523x_cpu_reset(void)void __init config_BSP (char *commandp,int size) { mach_reset = m523x_cpu_reset; -} - -/***************************************************************************/ - -static int __init init_BSP (void ) -{ +m523x_fec_init ();#ifdef CONFIG_SPI_COLDFIRE_QSPI m523x_qspi_init ();#endif -return 0 ; } -arch_initcall (init_BSP); -/***************************************************************************/
Signature · 1 line
1.7.0.4
PATCH 2/3 m68knommu: clean up init code in ColdFire 528x startup
From: Greg Ungerer <[email protected]>
We can move all the init calls in the initcall code into the more general arch setup code (which is config_BSP() here). That makes the 528x consistent with other ColdFire CPUs setup cod. It means we can get rif of the initcall setup here all together.
--- arch/m68k/platform/528x/config.c | 9 --------- 1 files changed, 0 insertions(+), 9 deletions(-)
arch/m68k/platform/528x/config.c +0 -9
@@ -103,21 +103,12 @@ void __init config_BSP(char *commandp, int size)#ifdef CONFIG_WILDFIREMOD mach_halt = wildfiremod_halt;#endif -} - -/***************************************************************************/ - -static int __init init_BSP (void ) -{ mach_reset = m528x_cpu_reset;m528x_uarts_init ();m528x_fec_init ();#ifdef CONFIG_SPI_COLDFIRE_QSPI m528x_qspi_init ();#endif -return 0 ; } -arch_initcall (init_BSP); -/***************************************************************************/
Signature · 1 line
1.7.0.4
PATCH 3/3 m68knommu: clean up init code in ColdFire 532x startup
In reply to [email protected]From: Greg Ungerer <[email protected]>
We can move all the init calls in the initcall code into the more general arch setup code (which is config_BSP() here). That makes the 532x consistent with other ColdFire CPUs setup code. It means we can get rid of the initcall setup here all together. Also make sure we set the arch mach_reset function pointer to get the local arch reset code called on reset.
--- arch/m68k/platform/532x/config.c | 21 +++++++-------------- 1 files changed, 7 insertions(+), 14 deletions(-)
arch/m68k/platform/532x/config.c +7 -14
@@ -82,6 +82,13 @@ void __init config_BSP(char *commandp, int size) }#endif + mach_reset = m532x_cpu_reset; +m532x_uarts_init (); +m532x_fec_init (); +#ifdef CONFIG_SPI_COLDFIRE_QSPI +m532x_qspi_init (); +#endif +#ifdef CONFIG_BDM_DISABLE /* * Disable the BDM clocking. This also turns off most of the rest of
@@ -93,20 +100,6 @@ void __init config_BSP(char *commandp, int size) }/***************************************************************************/ - -static int __init init_BSP (void ) -{ -m532x_uarts_init (); -m532x_fec_init (); -#ifdef CONFIG_SPI_COLDFIRE_QSPI -m532x_qspi_init (); -#endif -return 0 ; -} - -arch_initcall (init_BSP); - -/***************************************************************************/ /* Board initialization */ /***************************************************************************/ /*
Signature · 1 line
1.7.0.4