Skip to contentSkip to conversation

ASoC: wm8960: Support shared LRCLK

PATCH In review Mark Brown 2 participants 4 messages Sep 13, 2012 – Sep 14, 2012

Subsystems (3)
lore
Share & tools
lore

Mark Brown

author
#0 lore raw

PATCH 1/1 ASoC: wm8960: Support shared LRCLK

If the LRCLK is shared and the WM8960 is clock master then we should enable the LRCM bit to tell the device that it should drive LRCLK when either ADC or DAC is enabled rather than separately driving the two LRCLKs.

---
 include/sound/wm8960.h    |    2 ++
 sound/soc/codecs/wm8960.c |   11 +++++++++++
 2 files changed, 13 insertions(+)
include/sound/wm8960.h +2 -0
index 74e9a95..b5a1ab9e 100644
@@ -19,6 +19,8 @@ struct wm8960_data {
 	bool capless;  /* Headphone outputs configured in capless mode */
 
 	int dres;  /* Discharge resistance for headphone outputs */
+
+	bool shared_lrclk;  /* DAC and ADC LRCLKs are wired together */
 };
 
 #endif
sound/soc/codecs/wm8960.c +11 -0
index 7cb0d07c..8740423 100644
@@ -1029,6 +1029,7 @@ static const struct regmap_config wm8960_regmap = {
 static __devinit int wm8960_i2c_probe(struct i2c_client *i2c,
 				      const struct i2c_device_id *id)
 {
+	struct wm8960_data *pdata = dev_get_platdata(&i2c->dev);
 	struct wm8960_priv *wm8960;
 	int ret;
 
@@ -1041,6 +1042,16 @@ static __devinit int wm8960_i2c_probe(struct i2c_client *i2c,
 	if (IS_ERR(wm8960->regmap))
 		return PTR_ERR(wm8960->regmap);
 
+	if (pdata && pdata->shared_lrclk) {
+		ret = regmap_update_bits(wm8960->regmap, WM8960_ADDCTL2,
+					 0x4, 0x4);
+		if (ret != 0) {
+			dev_err(&i2c->dev, "Failed to enable LRCM: %d\n",
+				ret);
+			return ret;
+		}
+	}
+
 	i2c_set_clientdata(i2c, wm8960);
 
 	ret = snd_soc_register_codec(&i2c->dev,
Signature · 1 line
1.7.10.4
#1 lore raw

sound/soc/codecs/wm8960.c static __devinit int wm8960_i2c_probe(struct i2c_client *i2c, · line 1047

Quoted 2 lines · Mark Brown
sound/soc/codecs/wm8960.c +2 -0
+		ret = regmap_update_bits(wm8960->regmap, WM8960_ADDCTL2,
+					 0x4, 0x4);

This is not enough to get the codec working on my board.

What is the actual mechanism that enables the clock on the WM8960? I don't have an oscilloscope, not it's hard to tell what the hardware is actually doing. However, I suspect that the LRCLK is not running.

Signature · 2 lines
Timur Tabi
Linux kernel developer at Freescale
#2 lore raw
Quoted 7 lines · Timur Tabi
Quoted 2 lines

sound/soc/codecs/wm8960.c static __devinit int wm8960_i2c_probe(struct i2c_client *i2c, · line 1047

Quoted 2 lines
sound/soc/codecs/wm8960.c +2 -0
+		ret = regmap_update_bits(wm8960->regmap, WM8960_ADDCTL2,
+					 0x4, 0x4);

This is not enough to get the codec working on my board.

What is the actual mechanism that enables the clock on the WM8960? I don't have an oscilloscope, not it's hard to tell what the hardware is actually doing. However, I suspect that the LRCLK is not running.

Never mind, it works now. I understand that the DAPM controls need to be enabled for the clocks to actually run, as described here:

http://www.alsa-project.org/main/index.php/DAPM#When_things_don.27t_work

On the #alsa-soc, I was told that I could force on the control in my machine driver. Specifically, I was told this:

"in your board file you can always make an always on output in the DAPM map"

Can you tell me how to do this? Is there an example? I don't want to have to rely on user-space configuration to get playback to work.

Signature · 2 lines
Timur Tabi
Linux kernel developer at Freescale
author
#3 lore raw
Quoted 7 lines · Timur Tabi

On the #alsa-soc, I was told that I could force on the control in my machine driver. Specifically, I was told this:

"in your board file you can always make an always on output in the DAPM map"

Can you tell me how to do this? Is there an example? I don't want to have to rely on user-space configuration to get playback to work.

You can't force controls on in your machine driver. DAPM controls only affect routing so I'm really not sure what you're looking for here.

The advice you were given on the ASoC channel was to add a new widget in your board that's always connected to the DAC, just define some random output widget.