usb: ulpi: add indicator configuration function

index dde2585..23b59e7 100644
@@ -106,20 +106,44 @@ int ulpi_select_transceiver(struct ulpi_viewport *ulpi_vp, unsigned speed)
 	return ulpi_write(ulpi_vp, &ulpi->function_ctrl, val);
 }
 
-int ulpi_set_vbus(struct ulpi_viewport *ulpi_vp, int on, int ext_power,
-			int ext_ind)
+int ulpi_set_vbus(struct ulpi_viewport *ulpi_vp, int on, int ext_power)
 {
 	u32 flags = ULPI_OTG_DRVVBUS;
 	u8 *reg = on ? &ulpi->otg_ctrl_set : &ulpi->otg_ctrl_clear;
 
 	if (ext_power)
 		flags |= ULPI_OTG_DRVVBUS_EXT;
-	if (ext_ind)
-		flags |= ULPI_OTG_EXTVBUSIND;
 
 	return ulpi_write(ulpi_vp, reg, flags);
 }
 
+int ulpi_set_vbus_indicator(struct ulpi_viewport *ulpi_vp, int external,
+			int passthu, int complement)
+{
+	u32 flags, val;
+	u8 *reg;
+
+	reg = external ? &ulpi->otg_ctrl_set : &ulpi->otg_ctrl_clear;
+	val = ulpi_write(ulpi_vp, reg, ULPI_OTG_EXTVBUSIND);
+	if (val)
+		return val;
+
+	flags = passthu ? ULPI_IFACE_PASSTHRU : 0;
+	flags |= complement ? ULPI_IFACE_EXTVBUS_COMPLEMENT : 0;
+
+	val = ulpi_read(ulpi_vp, &ulpi->iface_ctrl);
+	if (val == ULPI_ERROR)
+		return val;
+
+	val = val & ~(ULPI_IFACE_PASSTHRU & ULPI_IFACE_EXTVBUS_COMPLEMENT);
+	val |= flags;
+	val = ulpi_write(ulpi_vp, &ulpi->iface_ctrl, val);
+	if (val)
+		return val;
+
+	return 0;
+}
+
 int ulpi_set_pd(struct ulpi_viewport *ulpi_vp, int enable)
 {
 	u32 val = ULPI_OTG_DP_PULLDOWN | ULPI_OTG_DM_PULLDOWN;

index 9a75c24..99166c4 100644
@@ -61,8 +61,17 @@ int ulpi_select_transceiver(struct ulpi_viewport *ulpi_vp, unsigned speed);
  *
  * returns 0 on success, ULPI_ERROR on failure.
  */
-int ulpi_set_vbus(struct ulpi_viewport *ulpi_vp,
-			int on, int ext_power, int ext_ind);
+int ulpi_set_vbus(struct ulpi_viewport *ulpi_vp, int on, int ext_power);
+
+/*
+ * Configure VBUS indicator
+ * @external		- external VBUS over-current indicator is used
+ * @passthru		- disables ANDing of internal VBUS comparator
+ *                    with external VBUS input
+ * @complement		- inverts the external VBUS input
+ */
+int ulpi_set_vbus_indicator(struct ulpi_viewport *ulpi_vp, int external,
+			int passthru, int complement);
 
 /*
  * Enable/disable pull-down resistors on D+ and D- USB lines.

216 lines not on this page · raw message

index 4bbd4aa..fdbd127 100644
@@ -100,10 +100,12 @@ struct usb_ctlr {
 
 	/* 0x410 */
 	uint usb1_legacy_ctrl;
-	uint reserved12[3];
+	uint reserved12[4];
 
-	/* 0x420 */
-	uint reserved13[56];
+	/* 0x424 */
+	uint ulpi_timing_ctrl_0;
+	uint ulpi_timing_ctrl_1;
+	uint reserved13[53];
 
 	/* 0x500 */
 	uint reserved14[64 * 3];

@@ -144,10 +146,24 @@ struct usb_ctlr {
 #define VBUS_SENSE_CTL_AB_SESS_VLD		2
 #define VBUS_SENSE_CTL_A_SESS_VLD		3
 
+/* USB2_IF_ULPI_TIMING_CTRL_0 */
+#define ULPI_OUTPUT_PINMUX_BYP			(1 << 10)
+#define ULPI_CLKOUT_PINMUX_BYP			(1 << 11)
+
+/* USB2_IF_ULPI_TIMING_CTRL_1 */
+#define ULPI_DATA_TRIMMER_LOAD			(1 << 0)
+#define ULPI_DATA_TRIMMER_SEL(x)		(((x) & 0x7) << 1)
+#define ULPI_STPDIRNXT_TRIMMER_LOAD		(1 << 16)
+#define ULPI_STPDIRNXT_TRIMMER_SEL(x)	(((x) & 0x7) << 17)
+#define ULPI_DIR_TRIMMER_LOAD			(1 << 24)
+#define ULPI_DIR_TRIMMER_SEL(x)			(((x) & 0x7) << 25)
+
 /* USBx_IF_USB_SUSP_CTRL_0 */
+#define ULPI_PHY_ENB				(1 << 13)
 #define UTMIP_PHY_ENB			        (1 << 12)
 #define UTMIP_RESET			        (1 << 11)
 #define USB_PHY_CLK_VALID			(1 << 7)
+#define USB_SUSP_CLR				(1 << 5)
 
 /* USBx_UTMIP_MISC_CFG1 */
 #define UTMIP_PLLU_STABLE_COUNT_SHIFT		6

@@ -203,12 +219,15 @@ struct usb_ctlr {
 /* SB2_CONTROLLER_2_USB2D_PORTSC1_0 */
 #define PTS_SHIFT				30
 #define PTS_MASK				(3U << PTS_SHIFT)
-#define PTS_UTMI	0
+#define PTS_UTMI		0
 #define PTS_RESERVED	1
-#define PTS_ULP		2
+#define PTS_ULPI		2
 #define PTS_ICUSB_SER	3
 
 #define STS					(1 << 29)
+#define WKOC				(1 << 22)
+#define WKDS				(1 << 21)
+#define WKCN				(1 << 20)
 
 /* USBx_UTMIP_XCVR_CFG0_0 */
 #define UTMIP_FORCE_PD_POWERDOWN		(1 << 14)