tps80031: Add mfd and regulator driver

TPS80031/ TPS80032 Fully Integrated Power Management with Power Path and Battery Charger. The device provides five configurable step-down converters, 11 general purpose LDOs, USB OTG Module, ADC, RTC, 2 PWM, System Voltage Regulator/Battery Charger with Power Path from USB, 32K clock generator.

Add the mfd core driver for TPS80031/TPS80032.

Signed-off-by Laxman Dewangan <[email protected]>

---
Changes from V1:
- remove the volatle api.
- add regmap irq regardless of client->irq.
- Correct the irq cleanups.
- remove usage of irq_base.
- remove suspend/resume
- Correct acroym and ES nomenclature.

Changes from V2:
- Merged regulator specific header file change on this patch.

 drivers/mfd/Kconfig          |   14 +
 drivers/mfd/Makefile         |    1 +
 drivers/mfd/tps80031.c       |  545 ++++++++++++++++++++++++++++++++++++
 include/linux/mfd/tps80031.h |  632 ++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 1192 insertions(+), 0 deletions(-)
 create mode 100644 drivers/mfd/tps80031.c
 create mode 100644 include/linux/mfd/tps80031.h

drivers/mfd/Kconfig +14 -0

index 637bcdf..a1caf81 100644
@@ -244,6 +244,20 @@ config MFD_TPS65912_SPI
 	  If you say yes here you get support for the TPS65912 series of
 	  PM chips with SPI interface.
 
+config MFD_TPS80031
+	bool "TI TPS80031/TPS80032 Power Management chips"
+	depends on I2C && GENERIC_HARDIRQS
+	select MFD_CORE
+	select REGMAP_I2C
+	select IRQ_DOMAIN
+	help
+	  If you say yes here you get support for the Texas Instruments
+	  TPS80031/ TPS80032 Fully Integrated Power Management with Power
+	  Path and Battery Charger. The device provides five configurable
+	  step-down converters, 11 general purpose LDOs, USB OTG Module,
+	  ADC, RTC, 2 PWM, System Voltage Regulator/Battery Charger with
+	  Power Path from USB, 32K clock generator.
+
 config MENELAUS
 	bool "Texas Instruments TWL92330/Menelaus PM chip"
 	depends on I2C=y && ARCH_OMAP2

drivers/mfd/Makefile +1 -0

index 296817c..3595f2d 100644
@@ -57,6 +57,7 @@ tps65912-objs                   := tps65912-core.o tps65912-irq.o
 obj-$(CONFIG_MFD_TPS65912)	+= tps65912.o
 obj-$(CONFIG_MFD_TPS65912_I2C)	+= tps65912-i2c.o
 obj-$(CONFIG_MFD_TPS65912_SPI)  += tps65912-spi.o
+obj-$(CONFIG_MFD_TPS80031)	+= tps80031.o
 obj-$(CONFIG_MENELAUS)		+= menelaus.o
 
 obj-$(CONFIG_TWL4030_CORE)	+= twl-core.o twl4030-irq.o twl6030-irq.o

drivers/mfd/tps80031.c new file +0 -0

new file mode 100644
index 0000000..55088e7

drivers/mfd/tps80031.c new file +22 -0

+ *
+ * MFD core driver for TI TPS80031/TPS80032 Fully Integrated
+ * Power Management with Power Path and Battery Charger
+ *
+ * Copyright (c) 2012, NVIDIA Corporation.
+ *
+ * Author: Laxman Dewangan <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any kind,
+ * whether express or implied; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA
+ * 02111-1307, USA
+ */

drivers/mfd/tps80031.c new file +3 -0

+#include <linux/pm.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>

drivers/mfd/tps80031.c new file +79 -0

+static int __devinit tps80031_probe(struct i2c_client *client,
+					const struct i2c_device_id *id)
+{
+	struct tps80031_platform_data *pdata = client->dev.platform_data;
+	struct tps80031 *tps80031;
+	int ret;
+	uint8_t es_version;
+	uint8_t ep_ver;
+	int i;
+
+	if (!pdata) {
+		dev_err(&client->dev, "tps80031 requires platform data\n");
+		return -EINVAL;
+	}
+
+	tps80031 = devm_kzalloc(&client->dev, sizeof(*tps80031), GFP_KERNEL);
+	if (!tps80031) {
+		dev_err(&client->dev, "Malloc failed for tps80031\n");
+		return -ENOMEM;
+	}
+
+	for (i = 0; i < TPS_NUM_SLAVES; i++) {
+		if (tps80031_slave_address[i] == client->addr)
+			tps80031->clients[i] = client;
+		else
+			tps80031->clients[i] = i2c_new_dummy(client->adapter,
+						tps80031_slave_address[i]);
+		if (!tps80031->clients[i]) {
+			dev_err(&client->dev, "can't attach client %d\n", i);
+			ret = -ENOMEM;
+			goto fail_client_reg;
+		}
+
+		i2c_set_clientdata(tps80031->clients[i], tps80031);
+		tps80031->regmap[i] = devm_regmap_init_i2c(tps80031->clients[i],
+					&tps80031_regmap_configs[i]);
+		if (IS_ERR(tps80031->regmap[i])) {
+			ret = PTR_ERR(tps80031->regmap[i]);
+			dev_err(&client->dev,
+				"regmap %d init failed, err %d\n", i, ret);
+			goto fail_client_reg;
+		}
+	}
+
+	ret = tps80031_read(&client->dev, SLAVE_ID3, TPS80031_JTAGVERNUM,
+			&es_version);
+	if (ret < 0) {
+		dev_err(&client->dev,
+			"Silicon version number read failed: %d\n", ret);
+		goto fail_client_reg;
+	}
+
+	ret = tps80031_read(&client->dev, SLAVE_ID3, TPS80031_EPROM_REV,
+			&ep_ver);
+	if (ret < 0) {
+		dev_err(&client->dev,
+			"Silicon eeprom version read failed: %d\n", ret);
+		goto fail_client_reg;
+	}
+
+	dev_info(&client->dev, "ES version 0x%02x and EPROM version 0x%02x\n",
+					es_version, ep_ver);
+	tps80031->es_version = es_version;
+	tps80031->dev = &client->dev;
+	i2c_set_clientdata(client, tps80031);
+	tps80031->chip_info = id->driver_data;
+
+	ret = tps80031_irq_init(tps80031, client->irq, pdata->irq_base);
+	if (ret) {
+		dev_err(&client->dev, "IRQ init failed: %d\n", ret);
+		goto fail_client_reg;
+	}
+
+	tps80031_pupd_init(tps80031, pdata);
+
+	tps80031_init_ext_control(tps80031, pdata);
+
+	ret = mfd_add_devices(tps80031->dev, -1,
+			tps80031_cell, ARRAY_SIZE(tps80031_cell),

drivers/mfd/tps80031.c new file +43 -0

+
+	mfd_remove_devices(tps80031->dev);
+
+	regmap_del_irq_chip(client->irq, tps80031->irq_data);
+
+	for (i = 0; i < TPS_NUM_SLAVES; i++) {
+		if (tps80031->clients[i] != client)
+			i2c_unregister_device(tps80031->clients[i]);
+	}
+	return 0;
+}
+
+static const struct i2c_device_id tps80031_id_table[] = {
+	{ "tps80031", TPS80031 },
+	{ "tps80032", TPS80032 },
+};
+MODULE_DEVICE_TABLE(i2c, tps80031_id_table);
+
+static struct i2c_driver tps80031_driver = {
+	.driver	= {
+		.name	= "tps80031",
+		.owner	= THIS_MODULE,
+	},
+	.probe		= tps80031_probe,
+	.remove		= __devexit_p(tps80031_remove),
+	.id_table	= tps80031_id_table,
+};
+
+static int __init tps80031_init(void)
+{
+	return i2c_add_driver(&tps80031_driver);
+}
+subsys_initcall(tps80031_init);
+
+static void __exit tps80031_exit(void)
+{
+	i2c_del_driver(&tps80031_driver);
+}
+module_exit(tps80031_exit);
+
+MODULE_AUTHOR("Laxman Dewangan <[email protected]>");
+MODULE_DESCRIPTION("TPS80031 core driver");
+MODULE_LICENSE("GPL v2");

include/linux/mfd/tps80031.h new file +0 -0

new file mode 100644
index 0000000..b8e1b4e

include/linux/mfd/tps80031.h new file +339 -0

+ *
+ * Copyright (c) 2012, NVIDIA Corporation.
+ *
+ * Author: Laxman Dewangan <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any kind,
+ * whether express or implied; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA
+ * 02111-1307, USA
+ */
+
+#ifndef __LINUX_MFD_TPS80031_H
+#define __LINUX_MFD_TPS80031_H
+
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+
+/* Pull-ups/Pull-downs */
+#define TPS80031_CFG_INPUT_PUPD1			0xF0
+#define TPS80031_CFG_INPUT_PUPD2			0xF1
+#define TPS80031_CFG_INPUT_PUPD3			0xF2
+#define TPS80031_CFG_INPUT_PUPD4			0xF3
+#define TPS80031_CFG_LDO_PD1				0xF4
+#define TPS80031_CFG_LDO_PD2				0xF5
+#define TPS80031_CFG_SMPS_PD				0xF6
+
+/* Real Time Clock */
+#define TPS80031_SECONDS_REG				0x00
+#define TPS80031_MINUTES_REG				0x01
+#define TPS80031_HOURS_REG				0x02
+#define TPS80031_DAYS_REG				0x03
+#define TPS80031_MONTHS_REG				0x04
+#define TPS80031_YEARS_REG				0x05
+#define TPS80031_WEEKS_REG				0x06
+#define TPS80031_ALARM_SECONDS_REG			0x08
+#define TPS80031_ALARM_MINUTES_REG			0x09
+#define TPS80031_ALARM_HOURS_REG			0x0A
+#define TPS80031_ALARM_DAYS_REG				0x0B
+#define TPS80031_ALARM_MONTHS_REG			0x0C
+#define TPS80031_ALARM_YEARS_REG			0x0D
+#define TPS80031_RTC_CTRL_REG				0x10
+#define TPS80031_RTC_STATUS_REG				0x11
+#define TPS80031_RTC_INTERRUPTS_REG			0x12
+#define TPS80031_RTC_COMP_LSB_REG			0x13
+#define TPS80031_RTC_COMP_MSB_REG			0x14
+#define TPS80031_RTC_RESET_STATUS_REG			0x16
+
+/*PMC Master Module */
+#define TPS80031_PHOENIX_START_CONDITION		0x1F
+#define TPS80031_PHOENIX_MSK_TRANSITION			0x20
+#define TPS80031_STS_HW_CONDITIONS			0x21
+#define TPS80031_PHOENIX_LAST_TURNOFF_STS		0x22
+#define TPS80031_VSYSMIN_LO_THRESHOLD			0x23
+#define TPS80031_VSYSMIN_HI_THRESHOLD			0x24
+#define TPS80031_PHOENIX_DEV_ON				0x25
+#define TPS80031_STS_PWR_GRP_STATE			0x27
+#define TPS80031_PH_CFG_VSYSLOW				0x28
+#define TPS80031_PH_STS_BOOT				0x29
+#define TPS80031_PHOENIX_SENS_TRANSITION		0x2A
+#define TPS80031_PHOENIX_SEQ_CFG			0x2B
+#define TPS80031_PRIMARY_WATCHDOG_CFG			0X2C
+#define TPS80031_KEY_PRESS_DUR_CFG			0X2D
+#define TPS80031_SMPS_LDO_SHORT_STS			0x2E
+
+/* PMC Slave Module - Broadcast */
+#define TPS80031_BROADCAST_ADDR_ALL			0x31
+#define TPS80031_BROADCAST_ADDR_REF			0x32
+#define TPS80031_BROADCAST_ADDR_PROV			0x33
+#define TPS80031_BROADCAST_ADDR_CLK_RST			0x34
+
+/* PMC Slave Module  SMPS Regulators */
+#define TPS80031_SMPS4_CFG_TRANS			0x41
+#define TPS80031_SMPS4_CFG_STATE			0x42
+#define TPS80031_SMPS4_CFG_VOLTAGE			0x44
+#define TPS80031_VIO_CFG_TRANS				0x47
+#define TPS80031_VIO_CFG_STATE				0x48
+#define TPS80031_VIO_CFG_FORCE				0x49
+#define TPS80031_VIO_CFG_VOLTAGE			0x4A
+#define TPS80031_VIO_CFG_STEP				0x48
+#define TPS80031_SMPS1_CFG_TRANS			0x53
+#define TPS80031_SMPS1_CFG_STATE			0x54
+#define TPS80031_SMPS1_CFG_FORCE			0x55
+#define TPS80031_SMPS1_CFG_VOLTAGE			0x56
+#define TPS80031_SMPS1_CFG_STEP				0x57
+#define TPS80031_SMPS2_CFG_TRANS			0x59
+#define TPS80031_SMPS2_CFG_STATE			0x5A
+#define TPS80031_SMPS2_CFG_FORCE			0x5B
+#define TPS80031_SMPS2_CFG_VOLTAGE			0x5C
+#define TPS80031_SMPS2_CFG_STEP				0x5D
+#define TPS80031_SMPS3_CFG_TRANS			0x65
+#define TPS80031_SMPS3_CFG_STATE			0x66
+#define TPS80031_SMPS3_CFG_VOLTAGE			0x68
+
+/* PMC Slave Module  LDO Regulators */
+#define TPS80031_VANA_CFG_TRANS				0x81
+#define TPS80031_VANA_CFG_STATE				0x82
+#define TPS80031_VANA_CFG_VOLTAGE			0x83
+#define TPS80031_LDO2_CFG_TRANS				0x85
+#define TPS80031_LDO2_CFG_STATE				0x86
+#define TPS80031_LDO2_CFG_VOLTAGE			0x87
+#define TPS80031_LDO4_CFG_TRANS				0x89
+#define TPS80031_LDO4_CFG_STATE				0x8A
+#define TPS80031_LDO4_CFG_VOLTAGE			0x8B
+#define TPS80031_LDO3_CFG_TRANS				0x8D
+#define TPS80031_LDO3_CFG_STATE				0x8E
+#define TPS80031_LDO3_CFG_VOLTAGE			0x8F
+#define TPS80031_LDO6_CFG_TRANS				0x91
+#define TPS80031_LDO6_CFG_STATE				0x92
+#define TPS80031_LDO6_CFG_VOLTAGE			0x93
+#define TPS80031_LDOLN_CFG_TRANS			0x95
+#define TPS80031_LDOLN_CFG_STATE			0x96
+#define TPS80031_LDOLN_CFG_VOLTAGE			0x97
+#define TPS80031_LDO5_CFG_TRANS				0x99
+#define TPS80031_LDO5_CFG_STATE				0x9A
+#define TPS80031_LDO5_CFG_VOLTAGE			0x9B
+#define TPS80031_LDO1_CFG_TRANS				0x9D
+#define TPS80031_LDO1_CFG_STATE				0x9E
+#define TPS80031_LDO1_CFG_VOLTAGE			0x9F
+#define TPS80031_LDOUSB_CFG_TRANS			0xA1
+#define TPS80031_LDOUSB_CFG_STATE			0xA2
+#define TPS80031_LDOUSB_CFG_VOLTAGE			0xA3
+#define TPS80031_LDO7_CFG_TRANS				0xA5
+#define TPS80031_LDO7_CFG_STATE				0xA6
+#define TPS80031_LDO7_CFG_VOLTAGE			0xA7
+
+/* PMC Slave Module  External Control */
+#define TPS80031_REGEN1_CFG_TRANS			0xAE
+#define TPS80031_REGEN1_CFG_STATE			0xAF
+#define TPS80031_REGEN2_CFG_TRANS			0xB1
+#define TPS80031_REGEN2_CFG_STATE			0xB2
+#define TPS80031_SYSEN_CFG_TRANS			0xB4
+#define TPS80031_SYSEN_CFG_STATE			0xB5
+
+/* PMC Slave Module  Internal Control */
+#define TPS80031_NRESPWRON_CFG_TRANS			0xB7
+#define TPS80031_NRESPWRON_CFG_STATE			0xB8
+#define TPS80031_CLK32KAO_CFG_TRANS			0xBA
+#define TPS80031_CLK32KAO_CFG_STATE			0xBB
+#define TPS80031_CLK32KG_CFG_TRANS			0xBD
+#define TPS80031_CLK32KG_CFG_STATE			0xBE
+#define TPS80031_CLK32KAUDIO_CFG_TRANS			0xC0
+#define TPS80031_CLK32KAUDIO_CFG_STATE			0xC1
+#define TPS80031_VRTC_CFG_TRANS				0xC3
+#define TPS80031_VRTC_CFG_STATE				0xC4
+#define TPS80031_BIAS_CFG_TRANS				0xC6
+#define TPS80031_BIAS_CFG_STATE				0xC7
+#define TPS80031_VSYSMIN_HI_CFG_TRANS			0xC9
+#define TPS80031_VSYSMIN_HI_CFG_STATE			0xCA
+#define TPS80031_RC6MHZ_CFG_TRANS			0xCC
+#define TPS80031_RC6MHZ_CFG_STATE			0xCD
+#define TPS80031_TMP_CFG_TRANS				0xCF
+#define TPS80031_TMP_CFG_STATE				0xD0
+
+/* PMC Slave Module  resources assignment */
+#define TPS80031_PREQ1_RES_ASS_A			0xD7
+#define TPS80031_PREQ1_RES_ASS_B			0xD8
+#define TPS80031_PREQ1_RES_ASS_C			0xD9
+#define TPS80031_PREQ2_RES_ASS_A			0xDA
+#define TPS80031_PREQ2_RES_ASS_B			0xDB
+#define TPS80031_PREQ2_RES_ASS_C			0xDC
+#define TPS80031_PREQ3_RES_ASS_A			0xDD
+#define TPS80031_PREQ3_RES_ASS_B			0xDE
+#define TPS80031_PREQ3_RES_ASS_C			0xDF
+
+/* PMC Slave Module  Miscellaneous */
+#define TPS80031_SMPS_OFFSET				0xE0
+#define TPS80031_SMPS_MULT				0xE3
+#define TPS80031_MISC1					0xE4
+#define TPS80031_MISC2					0xE5
+#define TPS80031_BBSPOR_CFG				0xE6
+#define TPS80031_TMP_CFG				0xE7
+
+/* Battery Charging Controller and Indicator LED */
+#define TPS80031_CONTROLLER_CTRL2			0xDA
+#define TPS80031_CONTROLLER_VSEL_COMP			0xDB
+#define TPS80031_CHARGERUSB_VSYSREG			0xDC
+#define TPS80031_CHARGERUSB_VICHRG_PC			0xDD
+#define TPS80031_LINEAR_CHRG_STS			0xDE
+#define TPS80031_CONTROLLER_INT_MASK			0xE0
+#define TPS80031_CONTROLLER_CTRL1			0xE1
+#define TPS80031_CONTROLLER_WDG				0xE2
+#define TPS80031_CONTROLLER_STAT1			0xE3
+#define TPS80031_CHARGERUSB_INT_STATUS			0xE4
+#define TPS80031_CHARGERUSB_INT_MASK			0xE5
+#define TPS80031_CHARGERUSB_STATUS_INT1			0xE6
+#define TPS80031_CHARGERUSB_STATUS_INT2			0xE7
+#define TPS80031_CHARGERUSB_CTRL1			0xE8
+#define TPS80031_CHARGERUSB_CTRL2			0xE9
+#define TPS80031_CHARGERUSB_CTRL3			0xEA
+#define TPS80031_CHARGERUSB_STAT1			0xEB
+#define TPS80031_CHARGERUSB_VOREG			0xEC
+#define TPS80031_CHARGERUSB_VICHRG			0xED
+#define TPS80031_CHARGERUSB_CINLIMIT			0xEE
+#define TPS80031_CHARGERUSB_CTRLLIMIT1			0xEF
+#define TPS80031_CHARGERUSB_CTRLLIMIT2			0xF0
+#define TPS80031_LED_PWM_CTRL1				0xF4
+#define TPS80031_LED_PWM_CTRL2				0xF5
+
+/* USB On-The-Go  */
+#define TPS80031_BACKUP_REG				0xFA
+#define TPS80031_USB_VENDOR_ID_LSB			0x00
+#define TPS80031_USB_VENDOR_ID_MSB			0x01
+#define TPS80031_USB_PRODUCT_ID_LSB			0x02
+#define TPS80031_USB_PRODUCT_ID_MSB			0x03
+#define TPS80031_USB_VBUS_CTRL_SET			0x04
+#define TPS80031_USB_VBUS_CTRL_CLR			0x05
+#define TPS80031_USB_ID_CTRL_SET			0x06
+#define TPS80031_USB_ID_CTRL_CLR			0x07
+#define TPS80031_USB_VBUS_INT_SRC			0x08
+#define TPS80031_USB_VBUS_INT_LATCH_SET			0x09
+#define TPS80031_USB_VBUS_INT_LATCH_CLR			0x0A
+#define TPS80031_USB_VBUS_INT_EN_LO_SET			0x0B
+#define TPS80031_USB_VBUS_INT_EN_LO_CLR			0x0C
+#define TPS80031_USB_VBUS_INT_EN_HI_SET			0x0D
+#define TPS80031_USB_VBUS_INT_EN_HI_CLR			0x0E
+#define TPS80031_USB_ID_INT_SRC				0x0F
+#define TPS80031_USB_ID_INT_LATCH_SET			0x10
+#define TPS80031_USB_ID_INT_LATCH_CLR			0x11
+#define TPS80031_USB_ID_INT_EN_LO_SET			0x12
+#define TPS80031_USB_ID_INT_EN_LO_CLR			0x13
+#define TPS80031_USB_ID_INT_EN_HI_SET			0x14
+#define TPS80031_USB_ID_INT_EN_HI_CLR			0x15
+#define TPS80031_USB_OTG_ADP_CTRL			0x16
+#define TPS80031_USB_OTG_ADP_HIGH			0x17
+#define TPS80031_USB_OTG_ADP_LOW			0x18
+#define TPS80031_USB_OTG_ADP_RISE			0x19
+#define TPS80031_USB_OTG_REVISION			0x1A
+
+/* Gas Gauge */
+#define TPS80031_FG_REG_00				0xC0
+#define TPS80031_FG_REG_01				0xC1
+#define TPS80031_FG_REG_02				0xC2
+#define TPS80031_FG_REG_03				0xC3
+#define TPS80031_FG_REG_04				0xC4
+#define TPS80031_FG_REG_05				0xC5
+#define TPS80031_FG_REG_06				0xC6
+#define TPS80031_FG_REG_07				0xC7
+#define TPS80031_FG_REG_08				0xC8
+#define TPS80031_FG_REG_09				0xC9
+#define TPS80031_FG_REG_10				0xCA
+#define TPS80031_FG_REG_11				0xCB
+
+/* General Purpose ADC */
+#define TPS80031_GPADC_CTRL				0x2E
+#define TPS80031_GPADC_CTRL2				0x2F
+#define TPS80031_RTSELECT_LSB				0x32
+#define TPS80031_RTSELECT_ISB				0x33
+#define TPS80031_RTSELECT_MSB				0x34
+#define TPS80031_GPSELECT_ISB				0x35
+#define TPS80031_CTRL_P1				0x36
+#define TPS80031_RTCH0_LSB				0x37
+#define TPS80031_RTCH0_MSB				0x38
+#define TPS80031_RTCH1_LSB				0x39
+#define TPS80031_RTCH1_MSB				0x3A
+#define TPS80031_GPCH0_LSB				0x3B
+#define TPS80031_GPCH0_MSB				0x3C
+
+/* SIM, MMC and Battery Detection */
+#define TPS80031_SIMDEBOUNCING				0xEB
+#define TPS80031_SIMCTRL				0xEC
+#define TPS80031_MMCDEBOUNCING				0xED
+#define TPS80031_MMCCTRL				0xEE
+#define TPS80031_BATDEBOUNCING				0xEF
+
+/* Vibrator Driver and PWMs */
+#define TPS80031_VIBCTRL				0x9B
+#define TPS80031_VIBMODE				0x9C
+#define TPS80031_PWM1ON					0xBA
+#define TPS80031_PWM1OFF				0xBB
+#define TPS80031_PWM2ON					0xBD
+#define TPS80031_PWM2OFF				0xBE
+
+/* Control Interface */
+#define TPS80031_INT_STS_A				0xD0
+#define TPS80031_INT_STS_B				0xD1
+#define TPS80031_INT_STS_C				0xD2
+#define TPS80031_INT_MSK_LINE_A				0xD3
+#define TPS80031_INT_MSK_LINE_B				0xD4
+#define TPS80031_INT_MSK_LINE_C				0xD5
+#define TPS80031_INT_MSK_STS_A				0xD6
+#define TPS80031_INT_MSK_STS_B				0xD7
+#define TPS80031_INT_MSK_STS_C				0xD8
+#define TPS80031_TOGGLE1				0x90
+#define TPS80031_TOGGLE2				0x91
+#define TPS80031_TOGGLE3				0x92
+#define TPS80031_PWDNSTATUS1				0x93
+#define TPS80031_PWDNSTATUS2				0x94
+#define TPS80031_VALIDITY0				0x17
+#define TPS80031_VALIDITY1				0x18
+#define TPS80031_VALIDITY2				0x19
+#define TPS80031_VALIDITY3				0x1A
+#define TPS80031_VALIDITY4				0x1B
+#define TPS80031_VALIDITY5				0x1C
+#define TPS80031_VALIDITY6				0x1D
+#define TPS80031_VALIDITY7				0x1E
+
+/* Version number related register */
+#define TPS80031_JTAGVERNUM				0x87
+#define TPS80031_EPROM_REV				0xDF
+
+/* GPADC Trimming Bits. */
+#define TPS80031_GPADC_TRIM0				0xCC
+#define TPS80031_GPADC_TRIM1				0xCD
+#define TPS80031_GPADC_TRIM2				0xCE
+#define TPS80031_GPADC_TRIM3				0xCF
+#define TPS80031_GPADC_TRIM4				0xD0
+#define TPS80031_GPADC_TRIM5				0xD1
+#define TPS80031_GPADC_TRIM6				0xD2
+#define TPS80031_GPADC_TRIM7				0xD3
+#define TPS80031_GPADC_TRIM8				0xD4
+#define TPS80031_GPADC_TRIM9				0xD5
+#define TPS80031_GPADC_TRIM10				0xD6
+#define TPS80031_GPADC_TRIM11				0xD7
+#define TPS80031_GPADC_TRIM12				0xD8
+#define TPS80031_GPADC_TRIM13				0xD9
+#define TPS80031_GPADC_TRIM14				0xDA
+#define TPS80031_GPADC_TRIM15				0xDB
+#define TPS80031_GPADC_TRIM16				0xDC
+#define TPS80031_GPADC_TRIM17				0xDD
+#define TPS80031_GPADC_TRIM18				0xDE
+
+/* TPS80031_CONTROLLER_STAT1 bit fields */
+#define CONTROLLER_STAT1_BAT_TEMP			0
+#define CONTROLLER_STAT1_BAT_REMOVED			1
+#define CONTROLLER_STAT1_VBUS_DET			2
+#define CONTROLLER_STAT1_VAC_DET			3
+#define CONTROLLER_STAT1_FAULT_WDG			4
+#define CONTROLLER_STAT1_LINCH_GATED			6
+/* TPS80031_CONTROLLER_INT_MASK bit filed */
+#define CONTROLLER_INT_MASK_MVAC_DET			0

include/linux/mfd/tps80031.h new file +12 -0

+
+#define EXT_CONTROL_CFG_TRANS				0
+#define EXT_CONTROL_CFG_STATE				1
+
+/* State register field */
+#define STATE_OFF					0x00
+#define STATE_ON					0x01
+#define STATE_MASK					0x03
+
+/* Trans register field */
+#define TRANS_ACTIVE_OFF				0x00
+#define TRANS_ACTIVE_ON					0x01

include/linux/mfd/tps80031.h new file +47 -0

+
+/* TPS80031_BBSPOR_CFG bit field */
+#define TPS80031_BBSPOR_CHG_EN				0x8
+#define TPS80031_MAX_REGISTER				0xFF
+
+/* Supported chips */
+enum chips {
+	TPS80031 = 0x00000001,
+	TPS80032 = 0x00000002,
+};
+
+enum {
+	TPS80031_INT_PWRON,
+	TPS80031_INT_RPWRON,
+	TPS80031_INT_SYS_VLOW,
+	TPS80031_INT_RTC_ALARM,
+	TPS80031_INT_RTC_PERIOD,
+	TPS80031_INT_HOT_DIE,
+	TPS80031_INT_VXX_SHORT,
+	TPS80031_INT_SPDURATION,
+	TPS80031_INT_WATCHDOG,
+	TPS80031_INT_BAT,
+	TPS80031_INT_SIM,
+	TPS80031_INT_MMC,
+	TPS80031_INT_RES,
+	TPS80031_INT_GPADC_RT,
+	TPS80031_INT_GPADC_SW2_EOC,
+	TPS80031_INT_CC_AUTOCAL,
+	TPS80031_INT_ID_WKUP,
+	TPS80031_INT_VBUSS_WKUP,
+	TPS80031_INT_ID,
+	TPS80031_INT_VBUS,
+	TPS80031_INT_CHRG_CTRL,
+	TPS80031_INT_EXT_CHRG,
+	TPS80031_INT_INT_CHRG,
+	TPS80031_INT_RES2,
+	TPS80031_INT_BAT_TEMP_OVRANGE,
+	TPS80031_INT_BAT_REMOVED,
+	TPS80031_INT_VBUS_DET,
+	TPS80031_INT_VAC_DET,
+	TPS80031_INT_FAULT_WDG,
+	TPS80031_INT_LINCH_GATED,
+
+	/* Last interrupt id to get the end number */
+	TPS80031_INT_NR,
+};
+

include/linux/mfd/tps80031.h new file +65 -0

+
+enum {
+	TPS80031_REGULATOR_VIO,
+	TPS80031_REGULATOR_SMPS1,
+	TPS80031_REGULATOR_SMPS2,
+	TPS80031_REGULATOR_SMPS3,
+	TPS80031_REGULATOR_SMPS4,
+	TPS80031_REGULATOR_VANA,
+	TPS80031_REGULATOR_LDO1,
+	TPS80031_REGULATOR_LDO2,
+	TPS80031_REGULATOR_LDO3,
+	TPS80031_REGULATOR_LDO4,
+	TPS80031_REGULATOR_LDO5,
+	TPS80031_REGULATOR_LDO6,
+	TPS80031_REGULATOR_LDO7,
+	TPS80031_REGULATOR_LDOLN,
+	TPS80031_REGULATOR_LDOUSB,
+	TPS80031_REGULATOR_VBUS,
+	TPS80031_REGULATOR_REGEN1,
+	TPS80031_REGULATOR_REGEN2,
+	TPS80031_REGULATOR_SYSEN,
+	TPS80031_REGULATOR_MAX,
+};
+
+/* Different configurations for the rails */
+enum {
+	/* USBLDO input selection */
+	USBLDO_INPUT_VSYS		= 0x00000001,
+	USBLDO_INPUT_PMID		= 0x00000002,
+
+	/* LDO3 output mode */
+	LDO3_OUTPUT_VIB			= 0x00000004,
+
+	/* VBUS configuration */
+	VBUS_DISCHRG_EN_PDN		= 0x00000004,
+	VBUS_SW_ONLY			= 0x00000008,
+	VBUS_SW_N_ID			= 0x00000010,
+};
+
+/* External controls requests */
+enum tps80031_ext_control {
+	PWR_REQ_INPUT_NONE	= 0x00000000,
+	PWR_REQ_INPUT_PREQ1	= 0x00000001,
+	PWR_REQ_INPUT_PREQ2	= 0x00000002,
+	PWR_REQ_INPUT_PREQ3	= 0x00000004,
+	PWR_OFF_ON_SLEEP	= 0x00000008,
+	PWR_ON_ON_SLEEP		= 0x00000010,
+};
+
+enum tps80031_pupd_pins {
+	TPS80031_PREQ1 = 0,
+	TPS80031_PREQ2A,
+	TPS80031_PREQ2B,
+	TPS80031_PREQ2C,
+	TPS80031_PREQ3,
+	TPS80031_NRES_WARM,
+	TPS80031_PWM_FORCE,
+	TPS80031_CHRG_EXT_CHRG_STATZ,
+	TPS80031_SIM,
+	TPS80031_MMC,
+	TPS80031_GPADC_START,
+	TPS80031_DVSI2C_SCL,
+	TPS80031_DVSI2C_SDA,
+	TPS80031_CTLI2C_SCL,
+	TPS80031_CTLI2C_SDA,

+#define TPS80031_RGEMAP_IRQ(_reg, _mask) \

* PGP Signed by an unknown key

Quoted 1 line · Laxman Dewangan

+#define TPS80031_RGEMAP_IRQ(_reg, _mask) \

Why RGEMAP_IRQ?

drivers/mfd/tps80031.c line 125

Quoted 8 lines

drivers/mfd/tps80031.c new file +8 -0

+static struct regmap_irq_chip tps80031_irq_chip = {
+	.name = "tps80031",
+	.irqs = tps80031_main_irqs,
+	.num_irqs = ARRAY_SIZE(tps80031_main_irqs),
+	.num_regs = 3,
+	.status_base = TPS80031_INT_STS_A,
+	.mask_base = TPS80031_INT_MSK_LINE_A,
+	.wake_base = 1,

I'm not sure your wake_base setting is sane here - this is expected to be a register. If it is a register why is it not a #define?

drivers/mfd/tps80031.c line 280

Quoted 9 lines

drivers/mfd/tps80031.c new file +9 -0

+static int __devinit tps80031_irq_init(struct tps80031 *tps80031, int irq,
+				int irq_base)
+{
+	struct device *dev = tps80031->dev;
+	int i, ret;
+
+	for (i = 0; i<  3; i++)
+		tps80031_write(dev, SLAVE_ID2,
+				TPS80031_INT_MSK_STS_A + i, 0x00);

regmap ought to be masking everything for you on init.

* Unknown Key
* 0x7EA229BD

Quoted 2 lines · Mark Brown

I'm not sure your wake_base setting is sane here - this is expected to be a register. If it is a register why is it not a #define?

There is no wake register. Here I kept for the incerease the wake conut so that irq_set_irq_wake() can be called.

I think it is also not correct after change
regmap: irq: initialize all irqs to wake disabled

I need to set the irq_wake(0 without the register.

There is 2 sets of registers which need to be configure, MASK and LINE enable.

* PGP Signed by an unknown key

Quoted 5 lines · Laxman Dewangan

Quoted 2 lines · Mark Brown

I'm not sure your wake_base setting is sane here - this is expected to be a register. If it is a register why is it not a #define?

There is no wake register. Here I kept for the incerease the wake conut so that irq_set_irq_wake() can be called.

So you want to write to random registers in the chip instead... that doesn't seem like a terribly clever idea.

Quoted 4 lines

I think it is also not correct after change
regmap: irq: initialize all irqs to wake disabled I need to set the irq_wake(0 without the register.

I can't really parse any of the above, sorry.

Quoted 2 lines

There is 2 sets of registers which need to be configure, MASK and LINE enable.

So what does the second one do?

Yes, this is not a good idea, We will need support for wakeup without wakeup registers.
Probably we need to add one more parameter, wake enable to control without wake_base.

Quoted 3 lines

Quoted 2 lines

There is 2 sets of registers which need to be configure, MASK and LINE enable.

So what does the second one do?

The MASK register used for updating status register when interrupt occurs and LINE register used to pass the status to actual interrupt line.

* PGP Signed by an unknown key

On Tue, Nov 13, 2012 at 09:35:45PM -0500, Laxman Dewangan wrote:

Quoted 4 lines

Yes, this is not a good idea, We will need support for wakeup without wakeup registers.
Probably we need to add one more parameter, wake enable to control without wake_base.

This does not seem sensible. Why would this be optional if it is useful? In any case, what you're doing in the driver here is clearly not the way forward.

Quoted 3 lines

This does not seem sensible. Why would this be optional if it is useful? In any case, what you're doing in the driver here is clearly not the way forward.

I was thinking of adding wake_enable in struct regmap_irq_chip and decide the wake support based on the value if wake_enable true or wake_base is non-zero. then wake support should be enable. The wake register write will happen only when wake_base is non-zero.

* PGP Signed by an unknown key

On Tue, Nov 13, 2012 at 10:01:26PM -0500, Laxman Dewangan wrote:

Quoted 7 lines

Quoted 3 lines

This does not seem sensible. Why would this be optional if it is useful? In any case, what you're doing in the driver here is clearly not the way forward.

I was thinking of adding wake_enable in struct regmap_irq_chip and decide the wake support based on the value if wake_enable true or wake_base is non-zero. then wake support should be enable. The wake register write will happen only when wake_base is non-zero.

But to repeat my question why would this be optional?

Add regulator driver for Texas Instrument TPS80031/TPS80032 device. TPS80031/ TPS80032 Fully Integrated Power Management with Power Path and Battery Charger. It has 5 configurable step-down converters, 11 general purpose LDOs, VBUS generator and digital output to control regulators.

Signed-off-by Laxman Dewangan <[email protected]>

---
Changes from V1:
- Rewrite dcdc get voltage apis.
- Remove -1 and +1 in vsel.
- Correct the vbus ops for sw and hw based.

Changes from V2:
- Move header file changes to first patch so easy to apply on subsystem tree.

 drivers/regulator/Kconfig              |    9 +
 drivers/regulator/Makefile             |    1 +
 drivers/regulator/tps80031-regulator.c |  789 ++++++++++++++++++++++++++++++++
 3 files changed, 799 insertions(+), 0 deletions(-)
 create mode 100644 drivers/regulator/tps80031-regulator.c

drivers/regulator/tps80031-regulator.c new file +0 -0

new file mode 100644
index 0000000..0484478
@@ -0,0 +1,789 @@

+static inline struct device *to_tps80031_dev(struct regulator_dev *rdev)

drivers/regulator/tps80031-regulator.c new file +3 -0

+{
+	return rdev_get_dev(rdev)->parent->parent;
+}

drivers/regulator/tps80031-regulator.c new file +23 -0

+	int ret;
+
+	if (ri->rinfo->force_reg) {
+		ret = tps80031_read(parent, ri->rinfo->volt_id,
+						ri->rinfo->force_reg, &vsel);
+		if (ret < 0) {
+			dev_err(ri->dev, "reg 0x%02x read failed, e = %d\n",
+					ri->rinfo->force_reg, ret);
+			return ret;
+		}
+
+		if (!(vsel & SMPS_CMD_MASK))
+			return vsel & SMPS_VSEL_MASK;
+	}
+	ret = tps80031_read(parent, ri->rinfo->volt_id,
+				ri->rinfo->volt_reg, &vsel);
+	if (ret < 0) {
+		dev_err(ri->dev, "reg 0x%02x read failed, e = %d\n",
+			ri->rinfo->volt_reg, ret);
+		return ret;
+	}
+	return vsel & SMPS_VSEL_MASK;
+}

drivers/regulator/tps80031-regulator.c new file +39 -0

+
+	ret = tps80031_read(parent, SLAVE_ID2,
+			TPS80031_CHARGERUSB_CTRL1, &ctrl1);
+	if (ret < 0) {
+		dev_err(ri->dev, "reg 0x%02x read failed, e = %d\n",
+			TPS80031_CHARGERUSB_CTRL1, ret);
+		return ret;
+	}
+	ret = tps80031_read(parent, SLAVE_ID2,
+				TPS80031_CHARGERUSB_CTRL3, &ctrl3);
+	if (ret < 0) {
+		dev_err(ri->dev, "reg 0x%02x read failed, e = %d\n",
+			TPS80031_CHARGERUSB_CTRL1, ret);
+		return ret;
+	}
+	if ((ctrl1 & OPA_MODE_EN) && (ctrl3 & BOOST_HW_PWR_EN))
+		return 1;
+	return ret;
+}
+
+static int tps80031_vbus_enable(struct regulator_dev *rdev)
+{
+	struct tps80031_regulator *ri = rdev_get_drvdata(rdev);
+	struct device *parent = to_tps80031_dev(rdev);
+	int ret;
+
+	ret = tps80031_set_bits(parent, SLAVE_ID2,
+				TPS80031_CHARGERUSB_CTRL1, OPA_MODE_EN);
+	if (ret < 0) {
+		dev_err(ri->dev, "reg 0x%02x read failed, e = %d\n",
+					TPS80031_CHARGERUSB_CTRL1, ret);
+		return ret;
+	}
+
+	ret = tps80031_set_bits(parent, SLAVE_ID2,
+				TPS80031_CHARGERUSB_CTRL3, BOOST_HW_PWR_EN);
+	if (ret < 0) {
+		dev_err(ri->dev, "reg 0x%02x read failed, e = %d\n",
+			TPS80031_CHARGERUSB_CTRL3, ret);

drivers/regulator/tps80031-regulator.c new file +39 -0

+
+	if (ri->config_flags & VBUS_DISCHRG_EN_PDN) {
+		ret = tps80031_write(parent, SLAVE_ID2,
+			USB_VBUS_CTRL_SET, VBUS_DISCHRG);
+		if (ret < 0) {
+			dev_err(ri->dev, "reg 0x%02x write failed, e = %d\n",
+				USB_VBUS_CTRL_SET, ret);
+			return ret;
+		}
+	}
+
+	ret = tps80031_clr_bits(parent, SLAVE_ID2,
+			TPS80031_CHARGERUSB_CTRL1,  OPA_MODE_EN);
+	if (ret < 0) {
+		dev_err(ri->dev, "reg 0x%02x clearbit failed, e = %d\n",
+				TPS80031_CHARGERUSB_CTRL1, ret);
+		return ret;
+	}
+
+	ret = tps80031_clr_bits(parent, SLAVE_ID2,
+				TPS80031_CHARGERUSB_CTRL3, BOOST_HW_PWR_EN);
+	if (ret < 0) {
+		dev_err(ri->dev, "reg 0x%02x clearbit failed, e = %d\n",
+				TPS80031_CHARGERUSB_CTRL3, ret);
+		return ret;
+	}
+
+	mdelay(DIV_ROUND_UP(ri->rinfo->desc.enable_time, 1000));
+	if (ri->config_flags & VBUS_DISCHRG_EN_PDN) {
+		ret = tps80031_write(parent, SLAVE_ID2,
+			USB_VBUS_CTRL_CLR, VBUS_DISCHRG);
+		if (ret < 0) {
+			dev_err(ri->dev, "reg 0x%02x write failed, e = %d\n",
+					USB_VBUS_CTRL_CLR, ret);
+			return ret;
+		}
+	}
+	return ret;
+}

drivers/regulator/tps80031-regulator.c new file +20 -0

+
+	if (ri->rinfo->preq_bit < 0)
+		goto skip_pwr_req_config;
+
+	ret = tps80031_ext_power_req_config(parent, ri->ext_ctrl_flag,
+			ri->rinfo->preq_bit, ri->rinfo->state_reg,
+			ri->rinfo->trans_reg);
+	if (ret < 0) {
+		dev_err(ri->dev, "ext powerreq config failed, err = %d\n", ret);
+		return ret;
+	}
+
+skip_pwr_req_config:
+	if (tps80031_pdata->ext_ctrl_flag & PWR_ON_ON_SLEEP) {
+		ret = tps80031_update(parent, SLAVE_ID1, ri->rinfo->trans_reg,
+				TRANS_SLEEP_ON, TRANS_SLEEP_MASK);
+		if (ret < 0) {
+			dev_err(ri->dev, "Reg 0x%02x update failed, e %d\n",
+					ri->rinfo->trans_reg, ret);
+			return ret;

drivers/regulator/tps80031-regulator.c new file +148 -0

+			if (ri->config_flags & USBLDO_INPUT_VSYS)
+				val = MISC2_LDOUSB_IN_VSYS;
+			else
+				val = MISC2_LDOUSB_IN_PMID;
+
+			ret = tps80031_update(parent, SLAVE_ID1,
+				TPS80031_MISC2, val, MISC2_LDOUSB_IN_MASK);
+			if (ret < 0) {
+				dev_err(ri->dev,
+					"LDOUSB config failed, e= %d\n", ret);
+				return ret;
+			}
+		}
+		break;
+
+	case TPS80031_REGULATOR_LDO3:
+		if (ri->config_flags & LDO3_OUTPUT_VIB) {
+			ret = tps80031_update(parent, SLAVE_ID1,
+				TPS80031_MISC2, MISC2_LDO3_SEL_VIB_VAL,
+				MISC2_LDO3_SEL_VIB_MASK);
+			if (ret < 0) {
+				dev_err(ri->dev,
+					"LDO3 config failed, e = %d\n", ret);
+				return ret;
+			}
+		}
+		break;
+
+	case TPS80031_REGULATOR_VBUS:
+		/* Provide SW control Ops if VBUS is SW control */
+		if (!(ri->config_flags & VBUS_SW_ONLY))
+			ri->rinfo->desc.ops = &tps80031_vbus_sw_ops;
+		break;
+	default:
+		break;
+	}
+
+	/* Configure Active state to ON, SLEEP to OFF and OFF_state to OFF */
+	ret = tps80031_update(parent, SLAVE_ID1, ri->rinfo->trans_reg,
+		TRANS_ACTIVE_ON | TRANS_SLEEP_OFF | TRANS_OFF_OFF,
+		TRANS_ACTIVE_MASK | TRANS_SLEEP_MASK | TRANS_OFF_MASK);
+	if (ret < 0) {
+		dev_err(ri->dev, "trans reg update failed, e %d\n", ret);
+		return ret;
+	}
+
+	return ret;
+}
+
+static int check_smps_mode_mult(struct device *parent,
+	struct tps80031_regulator *ri)
+{
+	int mult_offset;
+	int ret;
+	u8 smps_offset;
+	u8 smps_mult;
+
+	ret = tps80031_read(parent, SLAVE_ID1,
+			TPS80031_SMPS_OFFSET, &smps_offset);
+	if (ret < 0) {
+		dev_err(parent, "Error in reading smps offset register\n");
+		return ret;
+	}
+
+	ret = tps80031_read(parent, SLAVE_ID1,
+			TPS80031_SMPS_MULT, &smps_mult);
+	if (ret < 0) {
+		dev_err(parent, "Error in reading smps mult register\n");
+		return ret;
+	}
+
+	switch (ri->rinfo->desc.id) {
+	case TPS80031_REGULATOR_VIO:
+		mult_offset = SMPS_MULTOFFSET_VIO;
+		break;
+	case TPS80031_REGULATOR_SMPS1:
+		mult_offset = SMPS_MULTOFFSET_SMPS1;
+		break;
+	case TPS80031_REGULATOR_SMPS2:
+		mult_offset = SMPS_MULTOFFSET_SMPS2;
+		break;
+	case TPS80031_REGULATOR_SMPS3:
+		mult_offset = SMPS_MULTOFFSET_SMPS3;
+		break;
+	case TPS80031_REGULATOR_SMPS4:
+		mult_offset = SMPS_MULTOFFSET_SMPS4;
+		break;
+	case TPS80031_REGULATOR_LDO2:
+		ri->device_flags = smps_mult & BIT(5) ? TRACK_MODE_ENABLE : 0;
+		/* TRACK mode the ldo2 varies from 600mV to 1300mV */
+		if (ri->device_flags & TRACK_MODE_ENABLE) {
+			ri->rinfo->desc.min_uV = 600000;
+			ri->rinfo->desc.uV_step = 12500;
+			ri->rinfo->desc.n_voltages = 57;
+			ri->rinfo->desc.vsel_mask = LDO_TRACK_VSEL_MASK;
+		}
+		return 0;
+	default:
+		return 0;
+	}
+
+	ri->device_flags = (smps_offset & mult_offset) ? DCDC_OFFSET_EN : 0;
+	ri->device_flags |= (smps_mult & mult_offset) ? DCDC_EXTENDED_EN : 0;
+	switch (ri->device_flags) {
+	case 0:
+		ri->rinfo->desc.min_uV = 607700;
+		ri->rinfo->desc.uV_step = 12660;
+		break;
+	case DCDC_OFFSET_EN:
+		ri->rinfo->desc.min_uV = 700000;
+		ri->rinfo->desc.uV_step = 12500;
+		break;
+	case DCDC_EXTENDED_EN:
+		ri->rinfo->desc.min_uV = 1852000;
+		ri->rinfo->desc.uV_step = 38600;
+		break;
+	case DCDC_OFFSET_EN | DCDC_EXTENDED_EN:
+		ri->rinfo->desc.min_uV = 2161000;
+		ri->rinfo->desc.uV_step = 38600;
+		break;
+	}
+	return 0;
+}
+
+static int __devinit tps80031_regulator_probe(struct platform_device *pdev)
+{
+	struct tps80031_platform_data *pdata;
+	struct tps80031_regulator_platform_data *tps_pdata;
+	struct tps80031_regulator_info *rinfo;
+	struct tps80031_regulator *ri;
+	struct tps80031_regulator *pmic;
+	struct regulator_dev *rdev;
+	struct regulator_config config = { };
+	int ret;
+	int num;
+
+	pdata = dev_get_platdata(pdev->dev.parent);
+
+	if (!pdata) {
+		dev_err(&pdev->dev, "No platform data\n");
+		return -EINVAL;
+	}
+
+	pmic = devm_kzalloc(&pdev->dev,
+			TPS80031_REGULATOR_MAX * sizeof(*pmic), GFP_KERNEL);
+	if (!pmic) {
+		dev_err(&pdev->dev, "mem alloc for pmic failed\n");
+		return -ENOMEM;

drivers/regulator/tps80031-regulator.c new file +82 -0

+		config.dev = &pdev->dev;
+		config.init_data = NULL;
+		config.driver_data = ri;
+		if (tps_pdata) {
+			config.init_data = tps_pdata->reg_init_data;
+			ri->config_flags = tps_pdata->config_flags;
+			ri->ext_ctrl_flag = tps_pdata->ext_ctrl_flag;
+			ret = tps80031_regulator_config(pdev->dev.parent,
+					ri, tps_pdata);
+			if (ret < 0) {
+				dev_err(&pdev->dev,
+					"regulator config failed, e %d\n", ret);
+				goto fail;
+			}
+
+			ret = tps80031_power_req_config(pdev->dev.parent,
+					ri, tps_pdata);
+			if (ret < 0) {
+				dev_err(&pdev->dev,
+					"pwr_req config failed, err %d\n", ret);
+				goto fail;
+			}
+		}
+		rdev = regulator_register(&ri->rinfo->desc, &config);
+		if (IS_ERR_OR_NULL(rdev)) {
+			dev_err(&pdev->dev,
+				"register regulator failed %s\n",
+					ri->rinfo->desc.name);
+			ret = PTR_ERR(rdev);
+			goto fail;
+		}
+		ri->rdev = rdev;
+	}
+
+	platform_set_drvdata(pdev, pmic);
+	return 0;
+fail:
+	while (--num >= 0) {
+		ri = &pmic[num];
+		regulator_unregister(ri->rdev);
+	}
+	return ret;
+}
+
+static int __devexit tps80031_regulator_remove(struct platform_device *pdev)
+{
+	struct tps80031_regulator *pmic = platform_get_drvdata(pdev);
+	struct tps80031_regulator *ri = NULL;
+	int num;
+
+	for (num = 0; num < TPS80031_REGULATOR_MAX; ++num) {
+		ri = &pmic[num];
+		regulator_unregister(ri->rdev);
+	}
+	return 0;
+}
+
+static struct platform_driver tps80031_regulator_driver = {
+	.driver	= {
+		.name	= "tps80031-pmic",
+		.owner	= THIS_MODULE,
+	},
+	.probe		= tps80031_regulator_probe,
+	.remove		= __devexit_p(tps80031_regulator_remove),
+};
+
+static int __init tps80031_regulator_init(void)
+{
+	return platform_driver_register(&tps80031_regulator_driver);
+}
+subsys_initcall(tps80031_regulator_init);
+
+static void __exit tps80031_regulator_exit(void)
+{
+	platform_driver_unregister(&tps80031_regulator_driver);
+}
+module_exit(tps80031_regulator_exit);
+
+MODULE_ALIAS("platform:tps80031-regulator");
+MODULE_DESCRIPTION("Regulator Driver for TI TPS80031 PMIC");
+MODULE_AUTHOR("Laxman Dewangan <[email protected]>");
+MODULE_LICENSE("GPL v2");

Signature · 1 line

1.7.1.1

Add regulator driver for Texas Instrument TPS80031/TPS80032 device. TPS80031/ TPS80032 Fully Integrated Power Management with Power Path and Battery Charger. It has 5 configurable step-down converters, 11 general purpose LDOs, VBUS generator and digital output to control regulators.