lpfc 8.3.37: Removed use of NOP mailboxes for interrupt verification

diff -upNr a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c
@@ -7664,78 +7664,6 @@ out:
 }
 
 /**
- * lpfc_sli4_send_nop_mbox_cmds - Send sli-4 nop mailbox commands
- * @phba: pointer to lpfc hba data structure.
- * @cnt: number of nop mailbox commands to send.
- *
- * This routine is invoked to send a number @cnt of NOP mailbox command and
- * wait for each command to complete.
- *
- * Return: the number of NOP mailbox command completed.
- **/
-static int
-lpfc_sli4_send_nop_mbox_cmds(struct lpfc_hba *phba, uint32_t cnt)
-{
-	LPFC_MBOXQ_t *mboxq;
-	int length, cmdsent;
-	uint32_t mbox_tmo;
-	uint32_t rc = 0;
-	uint32_t shdr_status, shdr_add_status;
-	union lpfc_sli4_cfg_shdr *shdr;
-
-	if (cnt == 0) {
-		lpfc_printf_log(phba, KERN_WARNING, LOG_INIT,
-				"2518 Requested to send 0 NOP mailbox cmd\n");
-		return cnt;
-	}
-
-	mboxq = (LPFC_MBOXQ_t *)mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);
-	if (!mboxq) {
-		lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
-				"2519 Unable to allocate memory for issuing "
-				"NOP mailbox command\n");
-		return 0;
-	}
-
-	/* Set up NOP SLI4_CONFIG mailbox-ioctl command */
-	length = (sizeof(struct lpfc_mbx_nop) -
-		  sizeof(struct lpfc_sli4_cfg_mhdr));
-
-	for (cmdsent = 0; cmdsent < cnt; cmdsent++) {
-		lpfc_sli4_config(phba, mboxq, LPFC_MBOX_SUBSYSTEM_COMMON,
-				 LPFC_MBOX_OPCODE_NOP, length,
-				 LPFC_SLI4_MBX_EMBED);
-		if (!phba->sli4_hba.intr_enable)
-			rc = lpfc_sli_issue_mbox(phba, mboxq, MBX_POLL);
-		else {
-			mbox_tmo = lpfc_mbox_tmo_val(phba, mboxq);
-			rc = lpfc_sli_issue_mbox_wait(phba, mboxq, mbox_tmo);
-		}
-		if (rc == MBX_TIMEOUT)
-			break;
-		/* Check return status */
-		shdr = (union lpfc_sli4_cfg_shdr *)
-			&mboxq->u.mqe.un.sli4_config.header.cfg_shdr;
-		shdr_status = bf_get(lpfc_mbox_hdr_status, &shdr->response);
-		shdr_add_status = bf_get(lpfc_mbox_hdr_add_status,
-					 &shdr->response);
-		if (shdr_status || shdr_add_status || rc) {
-			lpfc_printf_log(phba, KERN_WARNING, LOG_INIT,
-					"2520 NOP mailbox command failed "
-					"status x%x add_status x%x mbx "
-					"status x%x\n", shdr_status,
-					shdr_add_status, rc);
-			break;
-		}
-	}
-
-	if (rc != MBX_TIMEOUT)
-		mempool_free(mboxq, phba->mbox_mem_pool);
-
-	return cmdsent;
-}
-
-/**
  * lpfc_sli4_pci_mem_setup - Setup SLI4 HBA PCI memory space.
  * @phba: pointer to lpfc hba data structure.
  *

@@ -8503,37 +8431,6 @@ lpfc_unset_hba(struct lpfc_hba *phba)
 }
 
 /**
- * lpfc_sli4_unset_hba - Unset SLI4 hba device initialization.
- * @phba: pointer to lpfc hba data structure.
- *
- * This routine is invoked to unset the HBA device initialization steps to
- * a device with SLI-4 interface spec.
- **/
-static void
-lpfc_sli4_unset_hba(struct lpfc_hba *phba)
-{
-	struct lpfc_vport *vport = phba->pport;
-	struct Scsi_Host  *shost = lpfc_shost_from_vport(vport);
-
-	spin_lock_irq(shost->host_lock);
-	vport->load_flag |= FC_UNLOADING;
-	spin_unlock_irq(shost->host_lock);
-
-	phba->pport->work_port_events = 0;
-
-	/* Stop the SLI4 device port */
-	lpfc_stop_port(phba);
-
-	lpfc_sli4_disable_intr(phba);
-
-	/* Reset SLI4 HBA FCoE function */
-	lpfc_pci_function_reset(phba);
-	lpfc_sli4_queue_destroy(phba);
-
-	return;
-}
-
-/**
  * lpfc_sli4_xri_exchange_busy_wait - Wait for device XRI exchange busy
  * @phba: Pointer to HBA context object.
  *

@@ -9595,7 +9492,6 @@ lpfc_pci_probe_one_s4(struct pci_dev *pd
 	struct Scsi_Host  *shost = NULL;
 	int error, ret;
 	uint32_t cfg_mode, intr_mode;
-	int mcnt;
 	int adjusted_fcp_io_channel;
 
 	/* Allocate memory for HBA structure */

@@ -9684,58 +9580,35 @@ lpfc_pci_probe_one_s4(struct pci_dev *pd
 	shost = lpfc_shost_from_vport(vport); /* save shost for error cleanup */
 	/* Now, trying to enable interrupt and bring up the device */
 	cfg_mode = phba->cfg_use_msi;
-	while (true) {
-		/* Put device to a known state before enabling interrupt */
-		lpfc_stop_port(phba);
-		/* Configure and enable interrupt */
-		intr_mode = lpfc_sli4_enable_intr(phba, cfg_mode);
-		if (intr_mode == LPFC_INTR_ERROR) {
-			lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
-					"0426 Failed to enable interrupt.\n");
-			error = -ENODEV;
-			goto out_free_sysfs_attr;
-		}
-		/* Default to single EQ for non-MSI-X */
-		if (phba->intr_type != MSIX)
-			adjusted_fcp_io_channel = 1;
-		else
-			adjusted_fcp_io_channel = phba->cfg_fcp_io_channel;
-		phba->cfg_fcp_io_channel = adjusted_fcp_io_channel;
-		/* Set up SLI-4 HBA */
-		if (lpfc_sli4_hba_setup(phba)) {
-			lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
-					"1421 Failed to set up hba\n");
-			error = -ENODEV;
-			goto out_disable_intr;
-		}
-
-		/* Send NOP mbx cmds for non-INTx mode active interrupt test */
-		if (intr_mode != 0)
-			mcnt = lpfc_sli4_send_nop_mbox_cmds(phba,
-							    LPFC_ACT_INTR_CNT);
 
-		/* Check active interrupts received only for MSI/MSI-X */
-		if (intr_mode == 0 ||
-		    phba->sli.slistat.sli_intr >= LPFC_ACT_INTR_CNT) {
-			/* Log the current active interrupt mode */
-			phba->intr_mode = intr_mode;
-			lpfc_log_intr_mode(phba, intr_mode);
-			break;
-		}
-		lpfc_printf_log(phba, KERN_INFO, LOG_INIT,
-				"0451 Configure interrupt mode (%d) "
-				"failed active interrupt test.\n",
-				intr_mode);
-		/* Unset the previous SLI-4 HBA setup. */
-		/*
-		 * TODO:  Is this operation compatible with IF TYPE 2
-		 * devices?  All port state is deleted and cleared.
-		 */
-		lpfc_sli4_unset_hba(phba);
-		/* Try next level of interrupt mode */
-		cfg_mode = --intr_mode;
+	/* Put device to a known state before enabling interrupt */
+	lpfc_stop_port(phba);
+	/* Configure and enable interrupt */
+	intr_mode = lpfc_sli4_enable_intr(phba, cfg_mode);
+	if (intr_mode == LPFC_INTR_ERROR) {
+		lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
+				"0426 Failed to enable interrupt.\n");
+		error = -ENODEV;
+		goto out_free_sysfs_attr;
+	}
+	/* Default to single EQ for non-MSI-X */
+	if (phba->intr_type != MSIX)
+		adjusted_fcp_io_channel = 1;
+	else
+		adjusted_fcp_io_channel = phba->cfg_fcp_io_channel;
+	phba->cfg_fcp_io_channel = adjusted_fcp_io_channel;
+	/* Set up SLI-4 HBA */
+	if (lpfc_sli4_hba_setup(phba)) {
+		lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
+				"1421 Failed to set up hba\n");
+		error = -ENODEV;
+		goto out_disable_intr;
 	}
 
+	/* Log the current active interrupt mode */
+	phba->intr_mode = intr_mode;
+	lpfc_log_intr_mode(phba, intr_mode);
+
 	/* Perform post initialization setup */
 	lpfc_post_init_setup(phba);