is it possilbe to have uboot find the kernel in the file system?
Is it possible to add my kernel to the rootfs partition rather than have a separate partition?
I am using U-Boot 1.3.4, on a at91sam9g20ek (256Mb Nand, 8Mb Nor), and use the sam-ba firmware upload tool.
I'd like to put everything on nand, ignore nor, and hold redundant areas, in perpetration for firmware updates.
My starting point is from the atmel Linux4SAM project:
Nor layout:
Logical address: 0xD0000000
size Address-Range
16895 Area 0: D0000000 to D00041FF (RO) Bootstrap
16895 Area 1: D0004200 to D00083FF Environment
236543 Area 2: D0008400 to D0041FFF (RO) U-Boot
2152687 Area 3: D0042000 to D0251FFF Kernel
6217727 Area 4: D0252000 to D083FFFF FS
Nand layout:
4194304: 0x000000000000-0x000000400000 : "bootstrap/uboot/kernel" 62914560 0x000000400000-0x000004000000 : "rootfs" 201226592 0x000004000000-0x000010000000 : "data"
bootargs:
mem=64M console=ttyS0,115200 mtdparts=atmel_nand:4M(bootstrap/uboot/kernel)ro,60M(rootfs),-(data) root=/dev/mtdblock1 rw rootfstype=jffs2
bootcmd:
cp.b 0xD0042000 0x22200000 0x0019306C; bootm 0x22200000
Dear John Stile,
Quoted 2 lines · In message <1357246601.7939.128.camel@genx> you wrote:
Is it possible to add my kernel to the rootfs partition rather than have a separate partition?
Yes, it is - assuming you use a storage device and a file system type supported by U-Boot.
Quoted 2 lines
I am using U-Boot 1.3.4, on a at91sam9g20ek (256Mb Nand, 8Mb Nor), and use the sam-ba firmware upload tool.
Oops... v1.3.4 is way over 4 years old. Please consider it hopelessly obsoleted and completely unsupported.
Quoted 2 lines
I'd like to put everything on nand, ignore nor, and hold redundant areas, in perpetration for firmware updates.
For NAND flash, you should use UBI UBIFS (and yes, U-Boot can load from a UBIFS file system). The first step to this goal is an update to recent code, though.
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de When in doubt, mumble; when in trouble, delegate; when in charge, ponder. -- James H. Boren
Quoted 18 lines · Wolfgang Denk
Dear John Stile,
Quoted 2 lines · In message <1357246601.7939.128.camel@genx> you wrote:
Is it possible to add my kernel to the rootfs partition rather than have a separate partition?
Yes, it is - assuming you use a storage device and a file system type supported by U-Boot.
Quoted 2 lines
I am using U-Boot 1.3.4, on a at91sam9g20ek (256Mb Nand, 8Mb Nor), and use the sam-ba firmware upload tool.
Oops... v1.3.4 is way over 4 years old. Please consider it hopelessly obsoleted and completely unsupported.
Quoted 2 lines
I'd like to put everything on nand, ignore nor, and hold redundant areas, in perpetration for firmware updates.
Quoted 8 lines
For NAND flash, you should use UBI UBIFS (and yes, U-Boot can load from a UBIFS file system). The first step to this goal is an update to recent code, though.
Best regards,
Wolfgang Denk
u-boot-2012.10.tar.bz2 does not have support for the at91sam9g20ek I treid to apply my patches for u-boot-1.3.4, but they are way too old. Is there a newer patch set?
Dear John Stile,
Quoted 4 lines · In message <1357265217.7939.131.camel@genx> you wrote:
u-boot-2012.10.tar.bz2 does not have support for the at91sam9g20ek I treid to apply my patches for u-boot-1.3.4, but they are way too old. Is there a newer patch set?
I see the following board configurations supported in current mainline
code: at91sam9g20ek_nandflash, at91sam9g20ek_dataflash_cs0, and at91sam9g20ek_dataflash_cs1 . Anything wrong with those?
Best regards,
Wolfgang Denk
Signature · 6 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de "The whole problem with the world is that fools and fanatics are always so certain of themselves, but wiser people so full of doubts." - Bertrand Russell
Quoted 11 lines · Wolfgang Denk
Dear John Stile,
Quoted 4 lines · In message <1357265217.7939.131.camel@genx> you wrote:
u-boot-2012.10.tar.bz2 does not have support for the at91sam9g20ek I treid to apply my patches for u-boot-1.3.4, but they are way too old. Is there a newer patch set?
I see the following board configurations supported in current mainline
code:at91sam9g20ek_nandflash,at91sam9g20ek_dataflash_cs0, andat91sam9g20ek_dataflash_cs1. Anything wrong with those?
I'm going to have to wrestle with buildroot's uboot configuration or something... But it would be helpful to know what he build error means.
my buildroot .config sets:
BR2_TARGET_UBOOT=y
BR2_TARGET_UBOOT_BOARDNAME="at91sam9g20ek"
BR2_TARGET_UBOOT_CUSTOM_TARBALL=y BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="ftp://ftp.denx.de/pub/u-boot/u-boot-2012.10.tar.bz2" BR2_TARGET_UBOOT_VERSION="custom"
BR2_TARGET_UBOOT_FORMAT_BIN=y
BR2_TARGET_AT91BOOTSTRAP=y
BR2_TARGET_AT91BOOTSTRAP_BOARD="at91sam9g20ek" BR2_TARGET_AT91BOOTSTRAP_DATAFLASH=y BR2_TARGET_AT91BOOTSTRAP_MEMORY="dataflash"
uboot build error:
Quoted 1 line
Quoted 1 line
Quoted 1 line
uboot custom Configuring
PATH="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/bin:/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin:/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/sbin/:/home/jstile/Komodo-Edit-7/bin:/home/jstile/Komodo-Edit-7/bin:/usr/local/bin:/usr/bin:/bin:/opt/bin:/usr/x86_64-pc-linux-gnu/gcc-bin/4.5.4:/usr/games/bin:/home/jstile/bin:/home/jstile/bin" AR="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-ar" AS="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-as" LD="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-ld" NM="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-nm" CC="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-gcc" GCC="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-gcc" CPP="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-cpp" CXX="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-g++" FC="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-gfortran" RANLIB="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-ranlib" STRIP="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-strip" OBJCOPY="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-objcopy" OBJDUMP="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-objdump" AR_FOR_BUILD="/usr/bin/ar" AS_FOR_BUILD="/usr/bin/as" CC_FOR_BUILD="/usr/bin/gcc" GCC_FOR_BUILD="/usr/bin/gcc" CXX_FOR_BUILD="/usr/bin/g++" FC_FOR_BUILD="/usr/bin/ld" LD_FOR_BUILD="/usr/bin/ld" CFLAGS_FOR_BUILD="-O2 -I/home/jstile/svn_rmserver/buildroot-2011.11/output/host/include -I/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/include" CXXFLAGS_FOR_BUILD="-I/home/jstile/svn_rmserver/buildroot-2011.11/output/host/include -I/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/include" LDFLAGS_FOR_BUILD="-L/home/jstile/svn_rmserver/buildroot-2011.11/output/host/lib -L/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/lib -Wl,-rpath,/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/lib" FCFLAGS_FOR_BUILD="" DEFAULT_ASSEMBLER="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-as" DEFAULT_LINKER="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-ld" CFLAGS="-pipe -Os -D_LARGEFILE_SOURCE -D_LARGEFILE64_SOURCE -D_FILE_OFFSET_BITS=64" CXXFLAGS="-pipe -Os -D_LARGEFILE_SOURCE -D_LARGEFILE64_SOURCE -D_FILE_OFFSET_BITS=64" LDFLAGS="" FCFLAGS="" PKG_CONFIG="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/pkg-config" PERLLIB="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/lib/perl" STAGING_DIR="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/arm-unknown-linux-uclibcgnueabi/sysroot" CONFIG_NOSOFTFLOAT=1 /usr/bin/make -j2 -C /home/jstile/svn_rmserver/buildroot-2011.11/output/build/uboot-custom CROSS_COMPILE=" /home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-" ARCH=arm at91sam9g20ek_config make[1]: Entering directory `/home/jstile/svn_rmserver/buildroot-2011.11/output/build/uboot-custom'
make[1]: Leaving directory `/home/jstile/svn_rmserver/buildroot-2011.11/output/build/uboot-custom'
make[1]: Entering directory `/home/jstile/svn_rmserver/buildroot-2011.11/output/build/uboot-custom'
make: *** No rule to make target `at91sam9g20ek_config'. Stop.
make[1]: *** [at91sam9g20ek_config] Error 1
make[1]: Leaving directory `/home/jstile/svn_rmserver/buildroot-2011.11/output/build/uboot-custom'
make: *** [/home/jstile/svn_rmserver/buildroot-2011.11/output/build/uboot-custom/.stamp_configured] Error 2
What should the target be?
Maybe my buildroot is also so old it doesn't support the new uboot configuration syntax?
Hello John,
Quoted 10 lines · John Stile
Quoted 9 lines · Wolfgang Denk
Dear John Stile,
Quoted 3 lines · In message <1357265217.7939.131.camel@genx> you wrote:
u-boot-2012.10.tar.bz2 does not have support for the at91sam9g20ek I treid to apply my patches for u-boot-1.3.4, but they are way too old. Is there a newer patch set?
I see the following board configurations supported in current mainline
code:at91sam9g20ek_nandflash,at91sam9g20ek_dataflash_cs0, andat91sam9g20ek_dataflash_cs1. Anything wrong with those?
note the trailing _nandflash, _dataflash_cs0 etc.
Quoted 15 lines
I'm going to have to wrestle with buildroot's uboot configuration or something... But it would be helpful to know what he build error means.
my buildroot .config sets:
BR2_TARGET_UBOOT=y
BR2_TARGET_UBOOT_BOARDNAME="at91sam9g20ek"
BR2_TARGET_UBOOT_CUSTOM_TARBALL=y BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="ftp://ftp.denx.de/pub/u-boot/u-boot-2012.10.tar.bz2" BR2_TARGET_UBOOT_VERSION="custom"
BR2_TARGET_UBOOT_FORMAT_BIN=y
BR2_TARGET_AT91BOOTSTRAP=y
BR2_TARGET_AT91BOOTSTRAP_BOARD="at91sam9g20ek" BR2_TARGET_AT91BOOTSTRAP_DATAFLASH=y BR2_TARGET_AT91BOOTSTRAP_MEMORY="dataflash"
Quoted 6 lines
uboot build error:
Quoted 1 line
Quoted 1 line
Quoted 1 line
uboot custom Configuring
PATH="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/bin:/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin:/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/sbin/:/home/jstile/Komodo-Edit-7/bin:/home/jstile/Komodo-Edit-7/bin:/usr/local/bin:/usr/bin:/bin:/opt/bin:/usr/x86_64-pc-linux-gnu/gcc-bin/4.5.4:/usr/games/bin:/home/jstile/bin:/home/jstile/bin" AR="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-ar" AS="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-as" LD="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-ld" NM="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-nm" CC="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-gcc" GCC="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-lin
ux-uclibcgnueabi-gcc" CPP="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-cpp" CXX="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-g++" FC="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-gfortran" RANLIB="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-ranlib" STRIP="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-strip" OBJCOPY="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-objcopy" OBJDUMP="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-objdump" AR_FOR_BUILD="/usr/bin/ar" AS_FOR_BUILD="/usr/bin/as" CC_FOR_BUILD="/usr/bin/gcc" GCC_FOR_BUILD="/usr/bin/gcc" CXX_FOR_BUILD="/usr/bin/g++" FC_FOR_BUILD="/usr/bin/ld" LD_FOR_BUILD="/usr/bin/ld" C FLAGS_FOR_BUILD="-O2 -I/home/jstile/svn_rmserver/buildroot-2011.11/output/host/include -I/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/include" CXXFLAGS_FOR_BUILD="-I/home/jstile/svn_rmserver/buildroot-2011.11/output/host/include -I/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/include" LDFLAGS_FOR_BUILD="-L/home/jstile/svn_rmserver/buildroot-2011.11/output/host/lib -L/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/lib -Wl,-rpath,/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/lib" FCFLAGS_FOR_BUILD="" DEFAULT_ASSEMBLER="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-as" DEFAULT_LINKER="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-ld" CFLAGS="-pipe -Os -D_LARGEFILE_SOURCE -D_LARGEFILE64_SOURCE -D_FILE_OFFSET_BITS=64" CXXFLAGS="-pipe -Os -D_LARGEFILE_SOURCE -D_LARGEFILE64_SOURCE -D_FILE_OFFSET_BITS=64" LDFLAGS="" FCFLAGS="" P KG_CONFIG="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/pkg-config" PERLLIB="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/lib/perl" STAGING_DIR="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/arm-unknown-linux-uclibcgnueabi/sysroot"CONFIG_NOSOFTFLOAT=1/usr/bin/make-j2 -C/home/jstile/svn_rmserver/buildroot-2011.11/output/build/uboot-customCROSS_COMPILE="/home/jstile/svn_rmserver/buildroot-2011.11/output/host/usr/bin/arm-unknown-linux-uclibcgnueabi-" ARCH=armat91sam9g20ek_config
last word, misses the _nandflash, you should get it there somehow..
Quoted 9 lines
make[1]: Entering directory
/home/jstile/svn_rmserver/buildroot-2011.11/output/build/uboot-custom' make[1]: Leaving directory/home/jstile/svn_rmserver/buildroot-2011.11/output/build/uboot-custom' make[1]: Entering directory `/home/jstile/svn_rmserver/buildroot-2011.11/output/build/uboot-custom'
make: *** No rule to make target `at91sam9g20ek_config'. Stop.
make[1]: *** [at91sam9g20ek_config] Error 1
make[1]: Leaving directory `/home/jstile/svn_rmserver/buildroot-2011.11/output/build/uboot-custom'
make: *** [/home/jstile/svn_rmserver/buildroot-2011.11/output/build/uboot-custom/.stamp_configured] Error 2What should the target be?
one of the ones listed in boards.cfg with _config appended, e.g. at91sam9g20ek_nandflash_config
Quoted 2 lines
Maybe my buildroot is also so old it doesn't support the new uboot configuration syntax?
no idea, since I don't use buildroot, but you might get around it by setting
BR2_TARGET_UBOOT_BOARDNAME="at91sam9g20ek_nandflash"
Regards,,
Jeroen
Dear John Stile,
Quoted 7 lines · In message <[email protected]> you wrote:
Quoted 4 lines
I see the following board configurations supported in current mainline
code:at91sam9g20ek_nandflash,at91sam9g20ek_dataflash_cs0, andat91sam9g20ek_dataflash_cs1. Anything wrong with those?I'm going to have to wrestle with buildroot's uboot configuration or something... But it would be helpful to know what he build error means.
...
Quoted 1 line
BR2_TARGET_UBOOT_BOARDNAME="at91sam9g20ek"
I don't know what "BOARDNAME" is exactly supposed to mean here, but probably this should be one of the configuration names I listed above.
...
Quoted 1 line
BR2_TARGET_AT91BOOTSTRAP_BOARD="at91sam9g20ek"
Or this? I have no idea what the difference between BOARDNAME and BOARD might be...
Quoted 1 line
BR2_TARGET_AT91BOOTSTRAP_MEMORY="dataflash"
OK, it appears you want one of the at91sam9g20ek_dataflash_csX configurations...
Quoted 1 line
make: *** No rule to make target `at91sam9g20ek_config'. Stop.
Well, as mentioned in my previous message, the known config names are "at91sam9g20ek_nandflash", "at91sam9g20ek_dataflash_cs0", and "at91sam9g20ek_dataflash_cs1"; plain "at91sam9g20ek" is NOT a known config name.
Quoted 1 line
What should the target be?
Depending whether you want to use CS0 or CS1 to address the dataflash on your board, it should probably be "at91sam9g20ek_dataflash_cs0" or "at91sam9g20ek_dataflash_cs1".
Quoted 2 lines
Maybe my buildroot is also so old it doesn't support the new uboot configuration syntax?
I think it's just misconfigured.
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de I don't see any direct evidence ... but, then, my crystal ball is in dire need of an ectoplasmic upgrade. :-) -- Howard Smith
Quoted 40 lines · Wolfgang Denk
Dear John Stile,
Quoted 7 lines · In message <[email protected]> you wrote:
Quoted 4 lines
I see the following board configurations supported in current mainline
code:at91sam9g20ek_nandflash,at91sam9g20ek_dataflash_cs0, andat91sam9g20ek_dataflash_cs1. Anything wrong with those?I'm going to have to wrestle with buildroot's uboot configuration or something... But it would be helpful to know what he build error means.
...
Quoted 1 line
BR2_TARGET_UBOOT_BOARDNAME="at91sam9g20ek"
I don't know what "BOARDNAME" is exactly supposed to mean here, but probably this should be one of the configuration names I listed above.
...
Quoted 1 line
BR2_TARGET_AT91BOOTSTRAP_BOARD="at91sam9g20ek"
Or this? I have no idea what the difference between BOARDNAME and BOARD might be...
Quoted 1 line
BR2_TARGET_AT91BOOTSTRAP_MEMORY="dataflash"
OK, it appears you want one of the
at91sam9g20ek_dataflash_csXconfigurations...Quoted 1 line
make: *** No rule to make target `at91sam9g20ek_config'. Stop.
Well, as mentioned in my previous message, the known config names are "
at91sam9g20ek_nandflash", "at91sam9g20ek_dataflash_cs0", and "at91sam9g20ek_dataflash_cs1"; plain "at91sam9g20ek" is NOT a known config name.Quoted 1 line
What should the target be?
Depending whether you want to use CS0 or CS1 to address the dataflash on your board, it should probably be "
at91sam9g20ek_dataflash_cs0" or "at91sam9g20ek_dataflash_cs1".
Quoted 9 lines
Quoted 2 lines
Maybe my buildroot is also so old it doesn't support the new uboot configuration syntax?
I think it's just misconfigured.
Best regards,
Wolfgang Denk
u-boot-2012.10 build does compile with buildroot's .conf settings BR2_TARGET_UBOOT_BOARDNAME="at91sam9g20ek_dataflash_cs1" or
BR2_TARGET_UBOOT_BOARDNAME="at91sam9g20ek_nandflash"
But after writing my ubootEnvtFileDataFlash.bin to NOR with sam-ba utility (which works with the u-boot-1.3.4), it is not found by the ROM boot loader, so I'm not sure where to go for help.
I know ROM boot loader executes what ever it finds at NOR start (0xD0000000) +0x00008400.
Does anyone else use a at91sam uboot-2012 and sam-ba, or have any other suggestions?
Hi John Stile,
Quoted 10 lines · John Stile
u-boot-2012.10 build does compile with buildroot's .conf settings BR2_TARGET_UBOOT_BOARDNAME="at91sam9g20ek_dataflash_cs1" or
BR2_TARGET_UBOOT_BOARDNAME="at91sam9g20ek_nandflash"But after writing my ubootEnvtFileDataFlash.bin to NOR with sam-ba utility (which works with the u-boot-1.3.4), it is not found by the ROM boot loader, so I'm not sure where to go for help.
Quoted 5 lines
I know ROM boot loader executes what ever it finds at NOR start (
0xD0000000) +0x00008400.Does anyone else use a at91sam uboot-2012 and sam-ba, or have any other suggestions?
Please check the text base of u-boot for at91sam9g20ek.
If you use the old bootstrap, it jump to 0x23f00000 after reading u-boot, while the v2012.10 u-boot use 0x21f00000 as its text base. If so, you can change u-boot or bootstrap to keep the two address the same.
Best Regards,
Bo Shen
Quoted 7 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot