Skip to contentSkip to conversation

block layer runtime pm

PATCH Superseded Aaron Lu 2 participants 13 messages Jan 30, 2013 – Feb 1, 2013

Subsystems (2)

v8 of 12 Superseded Latest is v12 →

lore
Share & tools
lore

Aaron Lu

author
#0 lore raw

v8 cover block layer runtime pm

In August 2010, Jens and Alan discussed about "Runtime PM and the block layer". http://marc.info/?t=128259108400001&r=1&w=2
And then Alan has given a detailed implementation guide:
http://marc.info/?l=linux-scsi&m=133727953625963&w=2

To test:

# ls -l /sys/block/sda
/sys/devices/pci0000:00/0000:00:1f.2/ata1/host0/target0:0:0/0:0:0:0/block/sda
# echo 10000 > /sys/devices/pci0000:00/0000:00:1f.2/ata1/host0/target0:0:0/0:0:0:0/power/autosuspend_delay_ms
# echo auto > /sys/devices/pci0000:00/0000:00:1f.2/ata1/host0/target0:0:0/0:0:0:0/power/control
Then you'll see sda is suspended after 10secs idle.
[ 1767.680192] sd 2:0:0:0: [sda] Synchronizing SCSI cache
[ 1767.680317] sd 2:0:0:0: [sda] Stopping disk

And if you do some IO, it will resume immediately.

[ 1791.052438] sd 2:0:0:0: [sda] Starting disk

For test, I often set the autosuspend time to 1 second. If you are using a GUI, the 10 seconds delay may be too long that the disk can not enter runtime suspended state.

Note that sd's runtime suspend callback will dump some kernel messages and the syslog daemon will write kernel message to /var/log/messages, making the disk instantly resume after suspended. So for test, the syslog daemon should better be temporarily stopped.

A git repo for it, on top of libata/upstream, scsi/for-next and block/for-next:
https://github.com/aaronlu/linux.git blockpm

v8:
- Set default autosuspend delay to -1 to avoid suspend till an updated value is set as suggested by Alan Stern;
- Always check the dev field of the queue structure, as it is incorrect and meaningless to do any operation on devices that do not use block layer runtime PM as reminded by Alan Stern;
- Update scsi bus level runtime PM callback to take care of scsi devices that use block layer runtime PM and that don't.

v7:
- Add kernel doc for block layer runtime PM API as suggested by Alan Stern;

- Add back check for q->dev, as that serves as a flag if driver is using block layer runtime PM;

- Do not auto suspend when last request is finished, as that's a hot path and auto suspend is not a trivial function. Instead, mark last busy in pre_suspend so that runtim PM core will retry suspend some time later to solve the 1st problem demostrated in v6, suggested by Alan Stern.

- Move block layer runtime PM strtegy functions to where they are needed instead of in include/linux/blkdev.h as suggested by Alan Stern since clients of block layer do not need to know those functions.

v6:
Take over from Lin Ming.

- Instead of put the device into autosuspend state in blk_post_runtime_suspend, do it when the last request is finished. This can also solve the problem illustrated below:

thread A thread B

|suspend timer expired			|
|  ... ...				|a new request comes in,
|  ... ...				|blk_pm_add_request
|  ... ...				|skip request_resume due to
|  ... ...				|q->status is still RPM_ACTIVE
|  rpm_suspend				|  ... ...
|    scsi_runtime_suspend		|  ... ...
|      blk_pre_runtime_suspend		|  ... ...
|      return -EBUSY due to nr_pending	|  ... ...
|  rpm_suspend done			|  ... ...
|					|    blk_pm_put_request, mark last busy

But no more trigger point, and the device will stay at RPM_ACTIVE state. Run pm_runtime_autosuspend after the last request is finished solved this problem.

- Requests which have the REQ_PM flag should not involve nr_pending counting, or we may lose the condition to resume the device:
Suppose queue is active and nr_pending is 0. Then a REQ_PM request comes and nr_pending will be increased to 1, but since the request has REQ_PM flag, it will not cause resume. Before it is finished, a normal request comes in, and since nr_pending is 1 now, it will not trigger the resume of the device either. Bug.

- Do not quiesce the device in scsi bus level runtime suspend callback. Since the only reason the device is to be runtime suspended is due to no more requests pending for it, quiesce it is pointless.

- Remove scsi_autopm_* from sd_check_events as we are request driven.

- Call blk_pm_runtime_init in scsi_sysfs_initialize_dev, so that we do not need to check queue's device in blk_pm_add/put_request.

- Do not mark last busy and initiate an autosuspend for the device in blk_pm_runtime_init function.

- Do not mark last busy and initiate an autosuspend for the device in block_post_runtime_resume, as when the request that triggered the resume finished, the blk_pm_put_request will mark last busy and initiate an autosuspend.

v5:
- rename scsi_execute_req to scsi_execute_req_flags
and wrap scsi_execute_req around it.
- add detail function descriptions in patch 2 log
- define static helper functions to do runtime pm work on block layer and put the definitions inside a #ifdef block

v4:
- add CONFIG_PM_RUNTIME check
- update queue runtime pm status after system resume
- use pm_runtime_autosuspend instead of pm_request_autosuspend in scsi_runtime_idle
- always count PM request

v3:
- remove block layer suspend/resume callbacks
- add block layer runtime pm helper functions

v2:
- remove queue idle timer, use runtime pm core's auto suspend

Lin Ming (4):
block: add a flag to identify PM request
block: add runtime pm helpers
block: implement runtime pm strategy
sd: change to auto suspend mode

 block/blk-core.c           | 182 +++++++++++++++++++++++++++++++++++++++++++++
 block/elevator.c           |  26 +++++++
 drivers/scsi/scsi_lib.c    |   9 +--
 drivers/scsi/scsi_pm.c     |  79 +++++++++++++++++---
 drivers/scsi/sd.c          |  21 ++----
 include/linux/blk_types.h  |   2 +
 include/linux/blkdev.h     |  27 +++++++
 include/scsi/scsi_device.h |  16 +++-
 8 files changed, 325 insertions(+), 37 deletions(-)
Signature · 1 line
1.8.1
author
#1 lore raw

PATCH v8 1/4 block: add a flag to identify PM request

From: Lin Ming <[email protected]>

Add a flag REQ_PM to identify the request is PM related, such requests will not change the device request queue's runtime status. It is intended to be used in driver's runtime PM callback, so that driver can perform some IO to the device there with the queue's runtime status unaffected. e.g. in SCSI disk's runtime suspend callback, the disk will be put into stopped power state, and this require sending a command to the device. Such command processing should not change the disk's runtime status.

As an example, modify scsi code to use this flag.

---
 drivers/scsi/scsi_lib.c    |  9 ++++-----
 drivers/scsi/sd.c          |  8 ++++----
 include/linux/blk_types.h  |  2 ++
 include/scsi/scsi_device.h | 16 ++++++++++++----
 4 files changed, 22 insertions(+), 13 deletions(-)
drivers/scsi/scsi_lib.c +4 -5
index 765398c..23f795f 100644
@@ -271,11 +271,10 @@ int scsi_execute(struct scsi_device *sdev, const unsigned char *cmd,
 }
 EXPORT_SYMBOL(scsi_execute);
 
-
-int scsi_execute_req(struct scsi_device *sdev, const unsigned char *cmd,
+int scsi_execute_req_flags(struct scsi_device *sdev, const unsigned char *cmd,
 		     int data_direction, void *buffer, unsigned bufflen,
 		     struct scsi_sense_hdr *sshdr, int timeout, int retries,
-		     int *resid)
+		     int *resid, int flags)
 {
 	char *sense = NULL;
 	int result;
@@ -286,14 +285,14 @@ int scsi_execute_req(struct scsi_device *sdev, const unsigned char *cmd,
 			return DRIVER_ERROR << 24;
 	}
 	result = scsi_execute(sdev, cmd, data_direction, buffer, bufflen,
-			      sense, timeout, retries, 0, resid);
+			      sense, timeout, retries, flags, resid);
 	if (sshdr)
 		scsi_normalize_sense(sense, SCSI_SENSE_BUFFERSIZE, sshdr);
 
 	kfree(sense);
 	return result;
 }
-EXPORT_SYMBOL(scsi_execute_req);
+EXPORT_SYMBOL(scsi_execute_req_flags);
 
 /*
  * Function:    scsi_init_cmd_errh()
drivers/scsi/sd.c +4 -4
index 7992635..698923f 100644
@@ -1424,8 +1424,8 @@ static int sd_sync_cache(struct scsi_disk *sdkp)
 		 * Leave the rest of the command zero to indicate
 		 * flush everything.
 		 */
-		res = scsi_execute_req(sdp, cmd, DMA_NONE, NULL, 0, &sshdr,
-				       SD_FLUSH_TIMEOUT, SD_MAX_RETRIES, NULL);
+		res = scsi_execute_req_flags(sdp, cmd, DMA_NONE, NULL, 0, &sshdr,
+				SD_FLUSH_TIMEOUT, SD_MAX_RETRIES, NULL, REQ_PM);
 		if (res == 0)
 			break;
 	}
@@ -3021,8 +3021,8 @@ static int sd_start_stop_device(struct scsi_disk *sdkp, int start)
 	if (!scsi_device_online(sdp))
 		return -ENODEV;
 
-	res = scsi_execute_req(sdp, cmd, DMA_NONE, NULL, 0, &sshdr,
-			       SD_TIMEOUT, SD_MAX_RETRIES, NULL);
+	res = scsi_execute_req_flags(sdp, cmd, DMA_NONE, NULL, 0, &sshdr,
+			       SD_TIMEOUT, SD_MAX_RETRIES, NULL, REQ_PM);
 	if (res) {
 		sd_printk(KERN_WARNING, sdkp, "START_STOP FAILED\n");
 		sd_print_result(sdkp, res);
include/linux/blk_types.h +2 -0
index cdf1119..fcc1ce2 100644
@@ -175,6 +175,7 @@ enum rq_flag_bits {
 	__REQ_IO_STAT,		/* account I/O stat */
 	__REQ_MIXED_MERGE,	/* merge of different types, fail separately */
 	__REQ_KERNEL, 		/* direct IO to kernel pages */
+	__REQ_PM,		/* runtime pm request */
 	__REQ_NR_BITS,		/* stops here */
 };
 
@@ -223,5 +224,6 @@ enum rq_flag_bits {
 #define REQ_MIXED_MERGE		(1 << __REQ_MIXED_MERGE)
 #define REQ_SECURE		(1 << __REQ_SECURE)
 #define REQ_KERNEL		(1 << __REQ_KERNEL)
+#define REQ_PM			(1 << __REQ_PM)
 
 #endif /* __LINUX_BLK_TYPES_H */
include/scsi/scsi_device.h +12 -4
index a7f9cba..cc64587 100644
@@ -394,10 +394,18 @@ extern int scsi_execute(struct scsi_device *sdev, const unsigned char *cmd,
 			int data_direction, void *buffer, unsigned bufflen,
 			unsigned char *sense, int timeout, int retries,
 			int flag, int *resid);
-extern int scsi_execute_req(struct scsi_device *sdev, const unsigned char *cmd,
-			    int data_direction, void *buffer, unsigned bufflen,
-			    struct scsi_sense_hdr *, int timeout, int retries,
-			    int *resid);
+extern int scsi_execute_req_flags(struct scsi_device *sdev,
+	const unsigned char *cmd, int data_direction, void *buffer,
+	unsigned bufflen, struct scsi_sense_hdr *sshdr, int timeout,
+	int retries, int *resid, int flags);
+static inline int scsi_execute_req(struct scsi_device *sdev,
+	const unsigned char *cmd, int data_direction, void *buffer,
+	unsigned bufflen, struct scsi_sense_hdr *sshdr, int timeout,
+	int retries, int *resid)
+{
+	return scsi_execute_req_flags(sdev, cmd, data_direction, buffer,
+		bufflen, sshdr, timeout, retries, resid, 0);
+}
 extern void sdev_disable_disk_events(struct scsi_device *sdev);
 extern void sdev_enable_disk_events(struct scsi_device *sdev);
 
Signature · 1 line
1.8.1
author
#2 lore raw

PATCH v8 2/4 block: add runtime pm helpers

In reply to Aaron Lu

From: Lin Ming <[email protected]>

Add runtime pm helper functions:

void blk_pm_runtime_init(struct request_queue *q, struct device *dev)
- Initialization function for drivers to call.

int blk_pre_runtime_suspend(struct request_queue *q)
- If any requests are in the queue, mark last busy and return -EBUSY.

    Otherwise set q->rpm_status to RPM_SUSPENDING and return 0.

void blk_post_runtime_suspend(struct request_queue *q, int err)
- If the suspend succeeded then set q->rpm_status to RPM_SUSPENDED. Otherwise set it to RPM_ACTIVE.

void blk_pre_runtime_resume(struct request_queue *q)
- Set q->rpm_status to RPM_RESUMING.

void blk_post_runtime_resume(struct request_queue *q, int err)
- If the resume succeeded then set q->rpm_status to RPM_ACTIVE and call __blk_run_queue, then mark last busy and autosuspend. Otherwise set q->rpm_status to RPM_SUSPENDED.

---
 block/blk-core.c       | 143 +++++++++++++++++++++++++++++++++++++++++++++++++
 include/linux/blkdev.h |  27 ++++++++++
 2 files changed, 170 insertions(+)
block/blk-core.c +143 -0
index 66d3168..1ec09f6 100644
@@ -30,6 +30,7 @@
 #include <linux/list_sort.h>
 #include <linux/delay.h>
 #include <linux/ratelimit.h>
+#include <linux/pm_runtime.h>
 
 #define CREATE_TRACE_POINTS
 #include <trace/events/block.h>
@@ -3043,6 +3044,148 @@ void blk_finish_plug(struct blk_plug *plug)
 }
 EXPORT_SYMBOL(blk_finish_plug);
 
+#ifdef CONFIG_PM_RUNTIME
+/**
+ * blk_pm_runtime_init - Block layer runtime PM initialization routine
+ * @q: the queue of the device
+ * @dev: the device the queue belongs to
+ *
+ * Description:
+ *    Initialize runtime-PM-related fields for @q and start auto suspend for
+ *    @dev. Drivers that want to take advantage of request-based runtime PM
+ *    should call this function after @dev has been initialized, and its
+ *    request queue @q has been allocated, and runtime PM for it can not happen
+ *    yet(either due to disabled/forbidden or its usage_count > 0). In most
+ *    cases, driver should call this function before any I/O has taken place.
+ *
+ *    This function takes care of setting up using auto suspend for the device,
+ *    the autosuspend delay is set to -1 to make runtime suspend impossible
+ *    until an updated value is either set by user or by driver. Drivers do
+ *    not need to touch other autosuspend settings.
+ *
+ *    The block layer runtime PM is request based, so only works for drivers
+ *    that use request as their IO unit instead of those directly use bio's.
+ */
+void blk_pm_runtime_init(struct request_queue *q, struct device *dev)
+{
+	q->dev = dev;
+	q->rpm_status = RPM_ACTIVE;
+	pm_runtime_set_autosuspend_delay(q->dev, -1);
+	pm_runtime_use_autosuspend(q->dev);
+	pm_runtime_mark_last_busy(q->dev);
+	pm_runtime_autosuspend(q->dev);
+}
+EXPORT_SYMBOL(blk_pm_runtime_init);
+
+/**
+ * blk_pre_runtime_suspend - Pre runtime suspend check
+ * @q: the queue of the device
+ *
+ * Description:
+ *    This function will check if runtime suspend is allowed for the device
+ *    by examining if there are any requests pending in the queue. If there
+ *    are requests pending, the device can not be runtime suspended; otherwise,
+ *    the queue's status will be updated to SUSPENDING and the driver can
+ *    proceed to suspend the device.
+ *
+ *    For the not allowed case, we mark last busy for the device so that
+ *    runtime PM core will try to autosuspend it some time later.
+ *
+ *    This function should be called near the start of the device's
+ *    runtime_suspend callback.
+ *
+ * Return:
+ *    0		- OK to runtime suspend the device
+ *    -EBUSY	- Device should not be runtime suspended
+ */
+int blk_pre_runtime_suspend(struct request_queue *q)
+{
+	int ret = 0;
+
+	spin_lock_irq(q->queue_lock);
+	if (q->nr_pending) {
+		ret = -EBUSY;
+		pm_runtime_mark_last_busy(q->dev);
+	} else {
+		q->rpm_status = RPM_SUSPENDING;
+	}
+	spin_unlock_irq(q->queue_lock);
+	return ret;
+}
+EXPORT_SYMBOL(blk_pre_runtime_suspend);
+
+/**
+ * blk_post_runtime_suspend - Post runtime suspend processing
+ * @q: the queue of the device
+ * @err: return value of the device's runtime_suspend function
+ *
+ * Description:
+ *    Update the queue's runtime status according to the return value of the
+ *    device's runtime suspend function.
+ *
+ *    This function should be called near the end of the device's
+ *    runtime_suspend callback.
+ */
+void blk_post_runtime_suspend(struct request_queue *q, int err)
+{
+	spin_lock_irq(q->queue_lock);
+	if (!err)
+		q->rpm_status = RPM_SUSPENDED;
+	else
+		q->rpm_status = RPM_ACTIVE;
+	spin_unlock_irq(q->queue_lock);
+}
+EXPORT_SYMBOL(blk_post_runtime_suspend);
+
+/**
+ * blk_pre_runtime_resume - Pre runtime resume processing
+ * @q: the queue of the device
+ *
+ * Description:
+ *    Update the queue's runtime status to RESUMING in preparation for the
+ *    runtime resume of the device.
+ *
+ *    This function should be called near the start of the device's
+ *    runtime_resume callback.
+ */
+void blk_pre_runtime_resume(struct request_queue *q)
+{
+	spin_lock_irq(q->queue_lock);
+	q->rpm_status = RPM_RESUMING;
+	spin_unlock_irq(q->queue_lock);
+}
+EXPORT_SYMBOL(blk_pre_runtime_resume);
+
+/**
+ * blk_post_runtime_resume - Post runtime resume processing
+ * @q: the queue of the device
+ * @err: return value of the device's runtime_resume function
+ *
+ * Description:
+ *    Update the queue's runtime status according to the return value of the
+ *    device's runtime_resume function. If it is successfully resumed, process
+ *    the requests that are queued into the device's queue when it is resuming
+ *    and then mark last busy and initiate autosuspend for it.
+ *
+ *    This function should be called near the end of the device's
+ *    runtime_resume callback.
+ */
+void blk_post_runtime_resume(struct request_queue *q, int err)
+{
+	spin_lock_irq(q->queue_lock);
+	if (!err) {
+		q->rpm_status = RPM_ACTIVE;
+		__blk_run_queue(q);
+		pm_runtime_mark_last_busy(q->dev);
+		pm_runtime_autosuspend(q->dev);
+	} else {
+		q->rpm_status = RPM_SUSPENDED;
+	}
+	spin_unlock_irq(q->queue_lock);
+}
+EXPORT_SYMBOL(blk_post_runtime_resume);
+#endif
+
 int __init blk_dev_init(void)
 {
 	BUILD_BUG_ON(__REQ_NR_BITS > 8 *
include/linux/blkdev.h +27 -0
index 78feda9..89d89c7 100644
@@ -361,6 +361,12 @@ struct request_queue {
 	 */
 	struct kobject kobj;
 
+#ifdef CONFIG_PM_RUNTIME
+	struct device		*dev;
+	int			rpm_status;
+	unsigned int		nr_pending;
+#endif
+
 	/*
 	 * queue settings
 	 */
@@ -961,6 +967,27 @@ struct request_queue *blk_alloc_queue_node(gfp_t, int);
 extern void blk_put_queue(struct request_queue *);
 
 /*
+ * block layer runtime pm functions
+ */
+#ifdef CONFIG_PM_RUNTIME
+extern void blk_pm_runtime_init(struct request_queue *q, struct device *dev);
+extern int blk_pre_runtime_suspend(struct request_queue *q);
+extern void blk_post_runtime_suspend(struct request_queue *q, int err);
+extern void blk_pre_runtime_resume(struct request_queue *q);
+extern void blk_post_runtime_resume(struct request_queue *q, int err);
+#else
+static inline void blk_pm_runtime_init(struct request_queue *q,
+	struct device *dev) {}
+static inline int blk_pre_runtime_suspend(struct request_queue *q)
+{
+	return -ENOSYS;
+}
+static inline void blk_post_runtime_suspend(struct request_queue *q, int err) {}
+static inline void blk_pre_runtime_resume(struct request_queue *q) {}
+static inline void blk_post_runtime_resume(struct request_queue *q, int err) {}
+#endif
+
+/*
  * blk_plug permits building a queue of related requests by holding the I/O
  * fragments for a short period. This allows merging of sequential requests
  * into single larger request. As the requests are moved from a per-task list to
Signature · 1 line
1.8.1
#3 lore raw

Re: [PATCH v8 2/4] block: add runtime pm helpers

Quoted 26 lines · Aaron Lu

From: Lin Ming <[email protected]>

Add runtime pm helper functions:

void blk_pm_runtime_init(struct request_queue *q, struct device *dev)
- Initialization function for drivers to call.

int blk_pre_runtime_suspend(struct request_queue *q)
- If any requests are in the queue, mark last busy and return -EBUSY.

    Otherwise set q->rpm_status to RPM_SUSPENDING and return 0.

void blk_post_runtime_suspend(struct request_queue *q, int err)
- If the suspend succeeded then set q->rpm_status to RPM_SUSPENDED. Otherwise set it to RPM_ACTIVE.

void blk_pre_runtime_resume(struct request_queue *q)
- Set q->rpm_status to RPM_RESUMING.

void blk_post_runtime_resume(struct request_queue *q, int err)
- If the resume succeeded then set q->rpm_status to RPM_ACTIVE and call __blk_run_queue, then mark last busy and autosuspend. Otherwise set q->rpm_status to RPM_SUSPENDED.

block/blk-core.c void blk_finish_plug(struct blk_plug *plug) · line 3076

Quoted 8 lines
block/blk-core.c +8 -0
+void blk_pm_runtime_init(struct request_queue *q, struct device *dev)
+{
+	q->dev = dev;
+	q->rpm_status = RPM_ACTIVE;
+	pm_runtime_set_autosuspend_delay(q->dev, -1);
+	pm_runtime_use_autosuspend(q->dev);
+	pm_runtime_mark_last_busy(q->dev);
+	pm_runtime_autosuspend(q->dev);

This last line is no longer needed. It can't do anything useful, since autosuspends are disabled (the delay is -1).

Alan Stern

author
#4 lore raw

Re: [PATCH v8 2/4] block: add runtime pm helpers

Quoted 28 lines · Alan Stern
Quoted 25 lines · Aaron Lu

From: Lin Ming <[email protected]>

Add runtime pm helper functions:

void blk_pm_runtime_init(struct request_queue *q, struct device *dev)
- Initialization function for drivers to call.

int blk_pre_runtime_suspend(struct request_queue *q)
- If any requests are in the queue, mark last busy and return -EBUSY.

    Otherwise set q->rpm_status to RPM_SUSPENDING and return 0.

void blk_post_runtime_suspend(struct request_queue *q, int err)
- If the suspend succeeded then set q->rpm_status to RPM_SUSPENDED. Otherwise set it to RPM_ACTIVE.

void blk_pre_runtime_resume(struct request_queue *q)
- Set q->rpm_status to RPM_RESUMING.

void blk_post_runtime_resume(struct request_queue *q, int err)
- If the resume succeeded then set q->rpm_status to RPM_ACTIVE and call __blk_run_queue, then mark last busy and autosuspend. Otherwise set q->rpm_status to RPM_SUSPENDED.

Quoted 11 lines

block/blk-core.c void blk_finish_plug(struct blk_plug *plug) · line 3076

Quoted 8 lines
block/blk-core.c +8 -0
+void blk_pm_runtime_init(struct request_queue *q, struct device *dev)
+{
+	q->dev = dev;
+	q->rpm_status = RPM_ACTIVE;
+	pm_runtime_set_autosuspend_delay(q->dev, -1);
+	pm_runtime_use_autosuspend(q->dev);
+	pm_runtime_mark_last_busy(q->dev);
+	pm_runtime_autosuspend(q->dev);

This last line is no longer needed. It can't do anything useful, since autosuspends are disabled (the delay is -1).

Right, thanks.
And the mark_last_busy can probably be removed too, it didn't make much sense here and we can add "driver should call pm_runtime_mark_last_busy and pm_runtime_autosuspend in its runtime idle callback" to the kernel doc. What do you think?

Thanks,
Aaron

#5 lore raw

Re: [PATCH v8 2/4] block: add runtime pm helpers

Quoted 12 lines · Aaron Lu
Quoted 11 lines

block/blk-core.c void blk_finish_plug(struct blk_plug *plug) · line 3076

Quoted 8 lines
block/blk-core.c +8 -0
+void blk_pm_runtime_init(struct request_queue *q, struct device *dev)
+{
+	q->dev = dev;
+	q->rpm_status = RPM_ACTIVE;
+	pm_runtime_set_autosuspend_delay(q->dev, -1);
+	pm_runtime_use_autosuspend(q->dev);
+	pm_runtime_mark_last_busy(q->dev);
+	pm_runtime_autosuspend(q->dev);

This last line is no longer needed. It can't do anything useful, since autosuspends are disabled (the delay is -1).

Quoted 5 lines

Right, thanks.
And the mark_last_busy can probably be removed too, it didn't make much sense here and we can add "driver should call pm_runtime_mark_last_busy and pm_runtime_autosuspend in its runtime idle callback" to the kernel doc. What do you think?

Yes, okay.

Alan Stern

author
#6 lore raw

PATCH v8 3/4 block: implement runtime pm strategy

In reply to Aaron Lu

From: Lin Ming <[email protected]>

When a request is added:
If device is suspended or is suspending and the request is not a PM request, resume the device.

When the last request finishes:
Call pm_runtime_mark_last_busy().

When pick a request:
If device is resuming/suspending, then only PM request is allowed to go.

---
 block/blk-core.c | 39 +++++++++++++++++++++++++++++++++++++++
 block/elevator.c | 26 ++++++++++++++++++++++++++
 2 files changed, 65 insertions(+)
block/blk-core.c +39 -0
index 1ec09f6..82cf678 100644
@@ -1264,6 +1264,16 @@ void part_round_stats(int cpu, struct hd_struct *part)
 }
 EXPORT_SYMBOL_GPL(part_round_stats);
 
+#ifdef CONFIG_PM_RUNTIME
+static void blk_pm_put_request(struct request *rq)
+{
+	if (rq->q->dev && !(rq->cmd_flags & REQ_PM) && !--rq->q->nr_pending)
+		pm_runtime_mark_last_busy(rq->q->dev);
+}
+#else
+static inline void blk_pm_put_request(struct request *rq) {}
+#endif
+
 /*
  * queue lock must be held
  */
@@ -1274,6 +1284,8 @@ void __blk_put_request(struct request_queue *q, struct request *req)
 	if (unlikely(--req->ref_count))
 		return;
 
+	blk_pm_put_request(req);
+
 	elv_completed_request(q, req);
 
 	/* this is a bio leak */
@@ -2051,6 +2063,28 @@ static void blk_account_io_done(struct request *req)
 	}
 }
 
+#ifdef CONFIG_PM_RUNTIME
+/*
+ * Don't process normal requests when queue is suspended
+ * or in the process of suspending/resuming
+ */
+static struct request *blk_pm_peek_request(struct request_queue *q,
+					   struct request *rq)
+{
+	if (q->dev && (q->rpm_status == RPM_SUSPENDED ||
+	    (q->rpm_status != RPM_ACTIVE && !(rq->cmd_flags & REQ_PM))))
+		return NULL;
+	else
+		return rq;
+}
+#else
+static inline struct request *blk_pm_peek_request(struct request_queue *q,
+						  struct request *rq)
+{
+	return rq;
+}
+#endif
+
 /**
  * blk_peek_request - peek at the top of a request queue
  * @q: request queue to peek at
@@ -2073,6 +2107,11 @@ struct request *blk_peek_request(struct request_queue *q)
 	int ret;
 
 	while ((rq = __elv_next_request(q)) != NULL) {
+
+		rq = blk_pm_peek_request(q, rq);
+		if (!rq)
+			break;
+
 		if (!(rq->cmd_flags & REQ_STARTED)) {
 			/*
 			 * This is the first time the device driver
block/elevator.c +26 -0
index 11683bb..29c5c7e 100644
@@ -34,6 +34,7 @@
 #include <linux/blktrace_api.h>
 #include <linux/hash.h>
 #include <linux/uaccess.h>
+#include <linux/pm_runtime.h>
 
 #include <trace/events/block.h>
 
@@ -515,6 +516,27 @@ void elv_bio_merged(struct request_queue *q, struct request *rq,
 		e->type->ops.elevator_bio_merged_fn(q, rq, bio);
 }
 
+#ifdef CONFIG_PM_RUNTIME
+static void blk_pm_requeue_request(struct request *rq)
+{
+	if (rq->q->dev && !(rq->cmd_flags & REQ_PM))
+		rq->q->nr_pending--;
+}
+
+static void blk_pm_add_request(struct request_queue *q, struct request *rq)
+{
+	if (q->dev && !(rq->cmd_flags & REQ_PM) && q->nr_pending++ == 0 &&
+	    (q->rpm_status == RPM_SUSPENDED || q->rpm_status == RPM_SUSPENDING))
+		pm_request_resume(q->dev);
+}
+#else
+static inline void blk_pm_requeue_request(struct request *rq) {}
+static inline void blk_pm_add_request(struct request_queue *q,
+				      struct request *rq)
+{
+}
+#endif
+
 void elv_requeue_request(struct request_queue *q, struct request *rq)
 {
 	/*
@@ -529,6 +551,8 @@ void elv_requeue_request(struct request_queue *q, struct request *rq)
 
 	rq->cmd_flags &= ~REQ_STARTED;
 
+	blk_pm_requeue_request(rq);
+
 	__elv_add_request(q, rq, ELEVATOR_INSERT_REQUEUE);
 }
 
@@ -551,6 +575,8 @@ void __elv_add_request(struct request_queue *q, struct request *rq, int where)
 {
 	trace_block_rq_insert(q, rq);
 
+	blk_pm_add_request(q, rq);
+
 	rq->q = q;
 
 	if (rq->cmd_flags & REQ_SOFTBARRIER) {
Signature · 1 line
1.8.1
author
#7 lore raw

PATCH v8 4/4 sd: change to auto suspend mode

In reply to Aaron Lu

From: Lin Ming <[email protected]>

Uses block layer runtime pm helper functions in scsi_runtime_suspend/resume for devices that take advantage of it.

Remove scsi_autopm_* from sd open/release path and check_events path.

---
 drivers/scsi/scsi_pm.c | 79 ++++++++++++++++++++++++++++++++++++++++++--------
 drivers/scsi/sd.c      | 13 +--------
 2 files changed, 68 insertions(+), 24 deletions(-)
drivers/scsi/scsi_pm.c +67 -12
index 8f6b12c..6ce00c5 100644
@@ -144,18 +144,44 @@ static int scsi_bus_restore(struct device *dev)
 
 #ifdef CONFIG_PM_RUNTIME
 
+static int scsi_blk_runtime_suspend(struct device *dev)
+{
+	struct scsi_device *sdev = to_scsi_device(dev);
+	int err;
+
+	err = blk_pre_runtime_suspend(sdev->request_queue);
+	if (err)
+		return err;
+	err = pm_generic_runtime_suspend(dev);
+	blk_post_runtime_suspend(sdev->request_queue, err);
+
+	return err;
+}
+
+static int scsi_dev_runtime_suspend(struct device *dev)
+{
+	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
+	int err;
+
+	err = scsi_dev_type_suspend(dev, pm ? pm->runtime_suspend : NULL);
+	if (err == -EAGAIN)
+		pm_schedule_suspend(dev, jiffies_to_msecs(
+					round_jiffies_up_relative(HZ/10)));
+
+	return err;
+}
+
 static int scsi_runtime_suspend(struct device *dev)
 {
 	int err = 0;
-	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
 
 	dev_dbg(dev, "scsi_runtime_suspend\n");
 	if (scsi_is_sdev_device(dev)) {
-		err = scsi_dev_type_suspend(dev,
-				pm ? pm->runtime_suspend : NULL);
-		if (err == -EAGAIN)
-			pm_schedule_suspend(dev, jiffies_to_msecs(
-				round_jiffies_up_relative(HZ/10)));
+		struct scsi_device *sdev = to_scsi_device(dev);
+		if (sdev->request_queue->dev)
+			err = scsi_blk_runtime_suspend(dev);
+		else
+			err = scsi_dev_runtime_suspend(dev);
 	}
 
 	/* Insert hooks here for targets, hosts, and transport classes */
@@ -163,14 +189,36 @@ static int scsi_runtime_suspend(struct device *dev)
 	return err;
 }
 
+static int scsi_blk_runtime_resume(struct device *dev)
+{
+	struct scsi_device *sdev = to_scsi_device(dev);
+	int err;
+
+	blk_pre_runtime_resume(sdev->request_queue);
+	err = pm_generic_runtime_resume(dev);
+	blk_post_runtime_resume(sdev->request_queue, err);
+
+	return err;
+}
+
+static int scsi_dev_runtime_resume(struct device *dev)
+{
+	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
+	return scsi_dev_type_resume(dev, pm ? pm->runtime_resume : NULL);
+}
+
 static int scsi_runtime_resume(struct device *dev)
 {
 	int err = 0;
-	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
 
 	dev_dbg(dev, "scsi_runtime_resume\n");
-	if (scsi_is_sdev_device(dev))
-		err = scsi_dev_type_resume(dev, pm ? pm->runtime_resume : NULL);
+	if (scsi_is_sdev_device(dev)) {
+		struct scsi_device *sdev = to_scsi_device(dev);
+		if (sdev->request_queue->dev)
+			err = scsi_blk_runtime_resume(dev);
+		else
+			err = scsi_dev_runtime_resume(dev);
+	}
 
 	/* Insert hooks here for targets, hosts, and transport classes */
 
@@ -185,10 +233,17 @@ static int scsi_runtime_idle(struct device *dev)
 
 	/* Insert hooks here for targets, hosts, and transport classes */
 
-	if (scsi_is_sdev_device(dev))
-		err = pm_schedule_suspend(dev, 100);
-	else
+	if (scsi_is_sdev_device(dev)) {
+		struct scsi_device *sdev = to_scsi_device(dev);
+		if (sdev->request_queue->dev) {
+			pm_runtime_mark_last_busy(dev);
+			err = pm_runtime_autosuspend(dev);
+		} else {
+			err = pm_schedule_suspend(dev, 100);
+		}
+	} else {
 		err = pm_runtime_suspend(dev);
+	}
 	return err;
 }
 
drivers/scsi/sd.c +1 -12
index 698923f..bf04dbf 100644
@@ -1121,10 +1121,6 @@ static int sd_open(struct block_device *bdev, fmode_t mode)
 
 	sdev = sdkp->device;
 
-	retval = scsi_autopm_get_device(sdev);
-	if (retval)
-		goto error_autopm;
-
 	/*
 	 * If the device is in error recovery, wait until it is done.
 	 * If the device is offline, then disallow any access to it.
@@ -1169,8 +1165,6 @@ static int sd_open(struct block_device *bdev, fmode_t mode)
 	return 0;
 
 error_out:
-	scsi_autopm_put_device(sdev);
-error_autopm:
 	scsi_disk_put(sdkp);
 	return retval;	
 }
@@ -1205,7 +1199,6 @@ static int sd_release(struct gendisk *disk, fmode_t mode)
 	 * XXX is followed by a "rmmod sd_mod"?
 	 */
 
-	scsi_autopm_put_device(sdev);
 	scsi_disk_put(sdkp);
 	return 0;
 }
@@ -1367,14 +1360,9 @@ static unsigned int sd_check_events(struct gendisk *disk, unsigned int clearing)
 	retval = -ENODEV;
 
 	if (scsi_block_when_processing_errors(sdp)) {
-		retval = scsi_autopm_get_device(sdp);
-		if (retval)
-			goto out;
-
 		sshdr  = kzalloc(sizeof(*sshdr), GFP_KERNEL);
 		retval = scsi_test_unit_ready(sdp, SD_TIMEOUT, SD_MAX_RETRIES,
 					      sshdr);
-		scsi_autopm_put_device(sdp);
 	}
 
 	/* failed to execute TUR, assume media not present */
@@ -2838,6 +2826,7 @@ static void sd_probe_async(void *data, async_cookie_t cookie)
 
 	sd_printk(KERN_NOTICE, sdkp, "Attached SCSI %sdisk\n",
 		  sdp->removable ? "removable " : "");
+	blk_pm_runtime_init(sdp->request_queue, dev);
 	scsi_autopm_put_device(sdp);
 	put_device(&sdkp->dev);
 }
Signature · 1 line
1.8.1
#8 lore raw

Re: [PATCH v8 4/4] sd: change to auto suspend mode

Quoted 9 lines · Aaron Lu

From: Lin Ming <[email protected]>

Uses block layer runtime pm helper functions in scsi_runtime_suspend/resume for devices that take advantage of it.

Remove scsi_autopm_* from sd open/release path and check_events path.

A couple of very minor suggestions...

drivers/scsi/scsi_pm.c static int scsi_bus_restore(struct device *dev) · line 149

Quoted 10 lines
drivers/scsi/scsi_pm.c +3 -0
@@ -144,18 +144,44 @@ static int scsi_bus_restore(struct device *dev)
 
 #ifdef CONFIG_PM_RUNTIME
 
+static int scsi_blk_runtime_suspend(struct device *dev)
+{
+	struct scsi_device *sdev = to_scsi_device(dev);

For this routine and the other new ones, it may be slightly more efficient to pass both dev and sdev as arguments (this depends on how smart the compiler's optimizer is). The caller already knows both of them, after all.

Quoted 27 lines
drivers/scsi/scsi_pm.c +24 -0
+	int err;
+
+	err = blk_pre_runtime_suspend(sdev->request_queue);
+	if (err)
+		return err;
+	err = pm_generic_runtime_suspend(dev);
+	blk_post_runtime_suspend(sdev->request_queue, err);
+
+	return err;
+}
+
+static int scsi_dev_runtime_suspend(struct device *dev)
+{
+	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
+	int err;
+
+	err = scsi_dev_type_suspend(dev, pm ? pm->runtime_suspend : NULL);
+	if (err == -EAGAIN)
+		pm_schedule_suspend(dev, jiffies_to_msecs(
+					round_jiffies_up_relative(HZ/10)));
+
+	return err;
+}
+
 static int scsi_runtime_suspend(struct device *dev)
 {
 	int err = 0;

drivers/scsi/scsi_pm.c static int scsi_bus_restore(struct device *dev) · line 180

Quoted 10 lines
drivers/scsi/scsi_pm.c +1 -6
-	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
 
 	dev_dbg(dev, "scsi_runtime_suspend\n");
 	if (scsi_is_sdev_device(dev)) {
-		err = scsi_dev_type_suspend(dev,
-				pm ? pm->runtime_suspend : NULL);
-		if (err == -EAGAIN)
-			pm_schedule_suspend(dev, jiffies_to_msecs(
-				round_jiffies_up_relative(HZ/10)));
+		struct scsi_device *sdev = to_scsi_device(dev);

There should be a blank line between the declaration and the executable code.

Quoted 16 lines
drivers/scsi/scsi_pm.c +9 -0
+		if (sdev->request_queue->dev)
+			err = scsi_blk_runtime_suspend(dev);
+		else
+			err = scsi_dev_runtime_suspend(dev);
 	}
 
 	/* Insert hooks here for targets, hosts, and transport classes */
@@ -163,14 +189,36 @@ static int scsi_runtime_suspend(struct device *dev)
 	return err;
 }
 
+static int scsi_blk_runtime_resume(struct device *dev)
+{
+	struct scsi_device *sdev = to_scsi_device(dev);
+	int err;
+

drivers/scsi/scsi_pm.c static int scsi_runtime_suspend(struct device *dev) · line 206

Quoted 10 lines
drivers/scsi/scsi_pm.c +10 -0
+	blk_pre_runtime_resume(sdev->request_queue);
+	err = pm_generic_runtime_resume(dev);
+	blk_post_runtime_resume(sdev->request_queue, err);
+
+	return err;
+}
+
+static int scsi_dev_runtime_resume(struct device *dev)
+{
+	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;

Blank line.

drivers/scsi/scsi_pm.c static int scsi_runtime_suspend(struct device *dev) · line 216

Quoted 13 lines
drivers/scsi/scsi_pm.c +5 -3
+	return scsi_dev_type_resume(dev, pm ? pm->runtime_resume : NULL);
+}
+
 static int scsi_runtime_resume(struct device *dev)
 {
 	int err = 0;
-	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
 
 	dev_dbg(dev, "scsi_runtime_resume\n");
-	if (scsi_is_sdev_device(dev))
-		err = scsi_dev_type_resume(dev, pm ? pm->runtime_resume : NULL);
+	if (scsi_is_sdev_device(dev)) {
+		struct scsi_device *sdev = to_scsi_device(dev);

Blank line.

Quoted 9 lines
drivers/scsi/scsi_pm.c +5 -0
+		if (sdev->request_queue->dev)
+			err = scsi_blk_runtime_resume(dev);
+		else
+			err = scsi_dev_runtime_resume(dev);
+	}
 
 	/* Insert hooks here for targets, hosts, and transport classes */
 

drivers/scsi/scsi_pm.c static int scsi_runtime_idle(struct device *dev) · line 237

Quoted 8 lines
drivers/scsi/scsi_pm.c +2 -3
@@ -185,10 +233,17 @@ static int scsi_runtime_idle(struct device *dev)
 
 	/* Insert hooks here for targets, hosts, and transport classes */
 
-	if (scsi_is_sdev_device(dev))
-		err = pm_schedule_suspend(dev, 100);
-	else
+	if (scsi_is_sdev_device(dev)) {
+		struct scsi_device *sdev = to_scsi_device(dev);

Blank line.

drivers/scsi/scsi_pm.c static int scsi_runtime_idle(struct device *dev) · line 248

Quoted 11 lines
drivers/scsi/scsi_pm.c +8 -0
+		if (sdev->request_queue->dev) {
+			pm_runtime_mark_last_busy(dev);
+			err = pm_runtime_autosuspend(dev);
+		} else {
+			err = pm_schedule_suspend(dev, 100);
+		}
+	} else {
 		err = pm_runtime_suspend(dev);
+	}
 	return err;
 }

Alan Stern

author
#9 lore raw

Re: [PATCH v8 4/4] sd: change to auto suspend mode

Quoted 21 lines · Alan Stern
Quoted 9 lines · Aaron Lu

From: Lin Ming <[email protected]>

Uses block layer runtime pm helper functions in scsi_runtime_suspend/resume for devices that take advantage of it.

Remove scsi_autopm_* from sd open/release path and check_events path.

A couple of very minor suggestions...

Quoted 7 lines
drivers/scsi/scsi_pm.c +0 -0
@@ -144,18 +144,44 @@ static int scsi_bus_restore(struct device *dev)
 
 #ifdef CONFIG_PM_RUNTIME
 
Quoted 8 lines

drivers/scsi/scsi_pm.c static int scsi_bus_restore(struct device *dev) · line 149

Quoted 3 lines
drivers/scsi/scsi_pm.c +3 -0
+static int scsi_blk_runtime_suspend(struct device *dev)
+{
+	struct scsi_device *sdev = to_scsi_device(dev);

For this routine and the other new ones, it may be slightly more efficient to pass both dev and sdev as arguments (this depends on how smart the compiler's optimizer is). The caller already knows both of them, after all.

What about passing only scsi_device? When device is needed, I can use &sdev->sdev_gendev. Is this equally efficient?

Quoted 5 lines
Quoted 5 lines
drivers/scsi/scsi_pm.c +0 -1
 static int scsi_runtime_suspend(struct device *dev)
 {
 	int err = 0;
-	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
 
Quoted 11 lines

drivers/scsi/scsi_pm.c static int scsi_bus_restore(struct device *dev) · line 180

Quoted 8 lines
drivers/scsi/scsi_pm.c +1 -5
 	dev_dbg(dev, "scsi_runtime_suspend\n");
 	if (scsi_is_sdev_device(dev)) {
-		err = scsi_dev_type_suspend(dev,
-				pm ? pm->runtime_suspend : NULL);
-		if (err == -EAGAIN)
-			pm_schedule_suspend(dev, jiffies_to_msecs(
-				round_jiffies_up_relative(HZ/10)));
+		struct scsi_device *sdev = to_scsi_device(dev);

There should be a blank line between the declaration and the executable code.

OK, will change this.

Quoted 12 lines

drivers/scsi/scsi_pm.c static int scsi_runtime_idle(struct device *dev) · line 237

Quoted 9 lines
drivers/scsi/scsi_pm.c +2 -3
@@ -185,10 +233,17 @@ static int scsi_runtime_idle(struct device *dev)
 
 	/* Insert hooks here for targets, hosts, and transport classes */
 
-	if (scsi_is_sdev_device(dev))
-		err = pm_schedule_suspend(dev, 100);
-	else
+	if (scsi_is_sdev_device(dev)) {
+		struct scsi_device *sdev = to_scsi_device(dev);

Blank line.

Quoted 10 lines

drivers/scsi/scsi_pm.c static int scsi_runtime_idle(struct device *dev) · line 247

Quoted 10 lines
drivers/scsi/scsi_pm.c +8 -0
+		if (sdev->request_queue->dev) {
+			pm_runtime_mark_last_busy(dev);
+			err = pm_runtime_autosuspend(dev);
+		} else {
+			err = pm_schedule_suspend(dev, 100);
+		}
+	} else {
 		err = pm_runtime_suspend(dev);
+	}
 	return err;

Shall we ignore the return value for these pm_xxx_suspend functions? I mean we do not need to record the return value for them and return it, since pm core doesn't care the return value of idle callback.

Thanks,
Aaron

#10 lore raw

Re: [PATCH v8 4/4] sd: change to auto suspend mode

Quoted 11 lines · Aaron Lu
Quoted 8 lines

drivers/scsi/scsi_pm.c static int scsi_bus_restore(struct device *dev) · line 149

Quoted 3 lines
drivers/scsi/scsi_pm.c +3 -0
+static int scsi_blk_runtime_suspend(struct device *dev)
+{
+	struct scsi_device *sdev = to_scsi_device(dev);

For this routine and the other new ones, it may be slightly more efficient to pass both dev and sdev as arguments (this depends on how smart the compiler's optimizer is). The caller already knows both of them, after all.

What about passing only scsi_device? When device is needed, I can use &sdev->sdev_gendev. Is this equally efficient?

I don't know... The difference is very small in any case. The routines will probably be inlined automatically.

Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
drivers/scsi/scsi_pm.c +6 -0
+		if (sdev->request_queue->dev) {
+			pm_runtime_mark_last_busy(dev);
+			err = pm_runtime_autosuspend(dev);
+		} else {
+			err = pm_schedule_suspend(dev, 100);
+		}
Quoted 8 lines
Quoted 4 lines

drivers/scsi/scsi_pm.c static int scsi_runtime_idle(struct device *dev) · line 247

Quoted 4 lines
drivers/scsi/scsi_pm.c +2 -0
+	} else {
 		err = pm_runtime_suspend(dev);
+	}
 	return err;

Shall we ignore the return value for these pm_xxx_suspend functions? I mean we do not need to record the return value for them and return it, since pm core doesn't care the return value of idle callback.

Maybe it will care in a future kernel version. You might as well store the return code and pass it back.

Alan Stern

author
#11 lore raw

Re: [PATCH v8 4/4] sd: change to auto suspend mode

Quoted 11 lines · Alan Stern
Quoted 9 lines · Aaron Lu
Quoted 8 lines

drivers/scsi/scsi_pm.c static int scsi_bus_restore(struct device *dev) · line 149

Quoted 3 lines
drivers/scsi/scsi_pm.c +3 -0
+static int scsi_blk_runtime_suspend(struct device *dev)
+{
+	struct scsi_device *sdev = to_scsi_device(dev);

For this routine and the other new ones, it may be slightly more efficient to pass both dev and sdev as arguments (this depends on how smart the compiler's optimizer is). The caller already knows both of them, after all.

Quoted 5 lines
Quoted 2 lines

What about passing only scsi_device? When device is needed, I can use &sdev->sdev_gendev. Is this equally efficient?

I don't know... The difference is very small in any case. The routines will probably be inlined automatically.

Indeed, I just checked the .s output of the three cases, they are all the same. So we just need to care about readability and less of code, passing only scsi_device seems to be the simplest, are you OK with this?

BTW, the compiler I used is gcc-4.7.2.

Quoted 16 lines
Quoted 15 lines
Quoted 11 lines

drivers/scsi/scsi_pm.c static int scsi_runtime_idle(struct device *dev) · line 247

Quoted 11 lines
drivers/scsi/scsi_pm.c +8 -0
+		if (sdev->request_queue->dev) {
+			pm_runtime_mark_last_busy(dev);
+			err = pm_runtime_autosuspend(dev);
+		} else {
+			err = pm_schedule_suspend(dev, 100);
+		}
+	} else {
 		err = pm_runtime_suspend(dev);
+	}
 	return err;

Shall we ignore the return value for these pm_xxx_suspend functions? I mean we do not need to record the return value for them and return it, since pm core doesn't care the return value of idle callback.

Quoted 2 lines

Maybe it will care in a future kernel version. You might as well store the return code and pass it back.

OK.

Thanks,
Aaron

#12 lore raw

Re: [PATCH v8 4/4] sd: change to auto suspend mode

Quoted 15 lines · Aaron Lu
Quoted 14 lines · Alan Stern
Quoted 11 lines · Aaron Lu
Quoted 8 lines

drivers/scsi/scsi_pm.c static int scsi_bus_restore(struct device *dev) · line 149

Quoted 3 lines
drivers/scsi/scsi_pm.c +3 -0
+static int scsi_blk_runtime_suspend(struct device *dev)
+{
+	struct scsi_device *sdev = to_scsi_device(dev);

For this routine and the other new ones, it may be slightly more efficient to pass both dev and sdev as arguments (this depends on how smart the compiler's optimizer is). The caller already knows both of them, after all.

What about passing only scsi_device? When device is needed, I can use &sdev->sdev_gendev. Is this equally efficient?

Quoted 6 lines
Quoted 2 lines

I don't know... The difference is very small in any case. The routines will probably be inlined automatically.

Indeed, I just checked the .s output of the three cases, they are all the same. So we just need to care about readability and less of code, passing only scsi_device seems to be the simplest, are you OK with this?

Yes, that's fine. Thanks for checking it out.

Alan Stern