Skip to contentSkip to conversation

PM: Introduce suspend state PM_SUSPEND_FREEZE

PATCH In review Zhang Rui 3 participants 11 messages Feb 4, 2013 – Feb 6, 2013

Subsystems (7)
lore
Share & tools
lore

Zhang Rui

author
#0 lore raw

PATCH v2 1/3 PM: Introduce suspend state PM_SUSPEND_FREEZE

PM_SUSPEND_FREEZE state is a general state that does not need any platform specific support, it equals frozen processes + suspended devices + idle processors.

Compared with PM_SUSPEND_MEMORY,
PM_SUSPEND_FREEZE saves less power
because the system is still in a running state. PM_SUSPEND_FREEZE has less resume latency because it does not touch BIOS, and the processors are in idle state.

Compared with RTPM/idle,
PM_SUSPEND_FREEZE saves more power as
1. the processor has longer sleep time because processes are frozen. The deeper c-state the processor supports, more power saving we can get.
2. PM_SUSPEND_FREEZE uses system suspend code path, thus we can get more power saving from the devices that does not have good RTPM support.

This state is useful for
1) platforms that do not have STR, or have a broken STR.
2) platforms that have an extremely low power idle state, which can be used to replace STR.

The following describes how PM_SUSPEND_FREEZE state works.
1. echo freeze > /sys/power/state
2. the processes are frozen.
3. all the devices are suspended.
4. all the processors are blocked by a wait queue
5. all the processors idles and enters (Deep) c-state.
6. an interrupt fires.
7. a processor is woken up and handles the irq.
8. if it is a general event,
a) the irq handler runs and quites.
b) goto step 4.
9. if it is a real wake event, say, power button pressing, keyboard touch, mouse moving,
a) the irq handler runs and activate the wakeup source
b) wakeup_source_activate() notifies the wait queue.
c) system starts resuming from PM_SUSPEND_FREEZE
10. all the devices are resumed.
11. all the processes are unfrozen.
12. system is back to working.

Known Issue:
The wakeup of this new PM_SUSPEND_FREEZE state may behave differently from the previous suspend state.
Take ACPI platform for example, there are some GPEs that only enabled when the system is in sleep state, to wake the system backk from S3/S4. But we are not touching these GPEs during transition to PM_SUSPEND_FREEZE. This means we may lose some wake event.
But on the other hand, as we do not disable all the Interrupts during PM_SUSPEND_FREEZE, we may get some extra "wakeup" Interrupts, that are not available for S3/S4.

The patches has been tested on an old Sony laptop, and here are the results:

Average Power:
1. RPTM/idle for half an hour:
14.8W, 12.6W, 14.1W, 12.5W, 14.4W, 13.2W, 12.9W
2. Freeze for half an hour:
11W, 10.4W, 9.4W, 11.3W 10.5W
3. RTPM/idle for three hours:
11.6W
4. Freeze for three hours:
10W
5. Suspend to Memory:
0.5~0.9W

Average Resume Latency:
1. RTPM/idle with a black screen: (From pressing keyboard to screen back) Less than 0.2s
2. Freeze: (From pressing power button to screen back)
2.50s
3. Suspend to Memory: (From pressing power button to screen back) 4.33s

Quoted 1 line

From the results, we can see that all the platforms should benefit from

this patch, even if it does not have Low Power S0.

---
 drivers/base/power/wakeup.c |    6 ++++
 include/linux/suspend.h     |    5 +++-
 kernel/power/main.c         |    2 +-
 kernel/power/suspend.c      |   69 +++++++++++++++++++++++++++++++++++--------
 4 files changed, 67 insertions(+), 15 deletions(-)
drivers/base/power/wakeup.c +6 -0
index e6ee5e8..79715e7 100644
@@ -382,6 +382,12 @@ static void wakeup_source_activate(struct wakeup_source *ws)
 {
 	unsigned int cec;
 
+	/*
+	 * active wakeup source should bring the system
+	 * out of PM_SUSPEND_FREEZE state
+	 */
+	freeze_wake();
+
 	ws->active = true;
 	ws->active_count++;
 	ws->last_time = ktime_get();
include/linux/suspend.h +4 -1
index 0c808d7..7420ab5 100644
@@ -34,8 +34,10 @@ static inline void pm_restore_console(void)
 typedef int __bitwise suspend_state_t;
 
 #define PM_SUSPEND_ON		((__force suspend_state_t) 0)
-#define PM_SUSPEND_STANDBY	((__force suspend_state_t) 1)
+#define PM_SUSPEND_FREEZE	((__force suspend_state_t) 1)
+#define PM_SUSPEND_STANDBY	((__force suspend_state_t) 2)
 #define PM_SUSPEND_MEM		((__force suspend_state_t) 3)
+#define PM_SUSPEND_MIN		PM_SUSPEND_FREEZE
 #define PM_SUSPEND_MAX		((__force suspend_state_t) 4)
 
 enum suspend_stat_step {
@@ -192,6 +194,7 @@ struct platform_suspend_ops {
  */
 extern void suspend_set_ops(const struct platform_suspend_ops *ops);
 extern int suspend_valid_only_mem(suspend_state_t state);
+extern void freeze_wake(void);
 
 /**
  * arch_suspend_disable_irqs - disable IRQs for suspend
kernel/power/main.c +1 -1
index 1c16f91..b1c26a9 100644
@@ -313,7 +313,7 @@ static ssize_t state_show(struct kobject *kobj, struct kobj_attribute *attr,
 static suspend_state_t decode_state(const char *buf, size_t n)
 {
 #ifdef CONFIG_SUSPEND
-	suspend_state_t state = PM_SUSPEND_STANDBY;
+	suspend_state_t state = PM_SUSPEND_MIN;
 	const char * const *s;
 #endif
 	char *p;
kernel/power/suspend.c +56 -13

162 lines not on this page · raw message

Signature · 1 line
1.7.9.5
author
#1 lore raw

PATCH v2 2/3 ACPI: enable ACPI SCI during suspend

Enable ACPI SCI during suspend so that SCI can be used as wake events for PM_SUSPEND_FREEZE.

For S3/S4 transition,
We disable all GPEs in suspend_ops->prepare_late() to fix a problem that GPEs may trigger SCI before arch_suspend_disable_irqs() is run.
So it is safe to leave the SCI enabled until arch_suspend_irq_disable() is run.

---
 drivers/acpi/osl.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/acpi/osl.c +1 -1
index 3ff2678..3adeb10 100644
@@ -787,7 +787,7 @@ acpi_os_install_interrupt_handler(u32 gsi, acpi_osd_handler handler,
 
 	acpi_irq_handler = handler;
 	acpi_irq_context = context;
-	if (request_irq(irq, acpi_irq, IRQF_SHARED, "acpi", acpi_irq)) {
+	if (request_irq(irq, acpi_irq, IRQF_SHARED | IRQF_NO_SUSPEND, "acpi", acpi_irq)) {
 		printk(KERN_ERR PREFIX "SCI (IRQ%d) allocation failed\n", irq);
 		acpi_irq_handler = NULL;
 		return AE_NOT_ACQUIRED;
Signature · 1 line
1.7.9.5
author
#2 lore raw

PATCH v2 3/3 i915: ignore lid open event when resuming

In reply to Zhang Rui

i915 driver needs to do modeset when
1. system resumes from sleep
2. lid is opened

In PM_SUSPEND_MEM state, all the GPEs are cleared when system resumes, thus it is the i915_resume code does the modeset rather than intel_lid_notify().

But in PM_SUSPEND_FREEZE state, this will be broken because
system is still responsive to the lid events.
1. When we close the lid in Freeze state, intel_lid_notify() sets modeset_on_lid.
2. When we reopen the lid, intel_lid_notify() will do a modeset, before the system is resumed.
here is the error log,

[92146.548074] WARNING: at drivers/gpu/drm/i915/intel_display.c:1028 intel_wait_for_pipe_off+0x184/0x190 [i915]()
[92146.548076] Hardware name: VGN-Z540N
[92146.548078] pipe_off wait timed out
[92146.548167] Modules linked in: hid_generic usbhid hid snd_hda_codec_realtek snd_hda_intel snd_hda_codec parport_pc snd_hwdep ppdev snd_pcm_oss i915 snd_mixer_oss snd_pcm arc4 iwldvm snd_seq_dummy mac80211 snd_seq_oss snd_seq_midi fbcon tileblit font bitblit softcursor drm_kms_helper snd_rawmidi snd_seq_midi_event coretemp drm snd_seq kvm btusb bluetooth snd_timer iwlwifi pcmcia tpm_infineon i2c_algo_bit joydev snd_seq_device intel_agp cfg80211 snd intel_gtt yenta_socket pcmcia_rsrc sony_laptop agpgart microcode psmouse tpm_tis serio_raw mxm_wmi soundcore snd_page_alloc tpm acpi_cpufreq lpc_ich pcmcia_core tpm_bios mperf processor lp parport firewire_ohci firewire_core crc_itu_t sdhci_pci sdhci thermal e1000e
[92146.548173] Pid: 4304, comm: kworker/0:0 Tainted: G        W    3.8.0-rc3-s0i3-v3-test+ #9
[92146.548175] Call Trace:
[92146.548189]  [<c10378e2>] warn_slowpath_common+0x72/0xa0
[92146.548227]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548263]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548270]  [<c10379b3>] warn_slowpath_fmt+0x33/0x40
[92146.548307]  [<f86398b4>] intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548344]  [<f86399c2>] intel_disable_pipe+0x102/0x190 [i915]
[92146.548380]  [<f8639ea4>] ? intel_disable_plane+0x64/0x80 [i915]
[92146.548417]  [<f8639f7c>] i9xx_crtc_disable+0xbc/0x150 [i915]
[92146.548456]  [<f863ebee>] intel_crtc_update_dpms+0x5e/0x90 [i915]
[92146.548493]  [<f86437cf>] intel_modeset_setup_hw_state+0x42f/0x8f0 [i915]
[92146.548535]  [<f8645b0b>] intel_lid_notify+0x9b/0xc0 [i915]
[92146.548543]  [<c15610d3>] notifier_call_chain+0x43/0x60
[92146.548550]  [<c105d1e1>] __blocking_notifier_call_chain+0x41/0x80
[92146.548556]  [<c105d23f>] blocking_notifier_call_chain+0x1f/0x30
[92146.548563]  [<c131a684>] acpi_lid_send_state+0x78/0xa4
[92146.548569]  [<c131aa9e>] acpi_button_notify+0x3b/0xf1
[92146.548577]  [<c12df56a>] ? acpi_os_execute+0x17/0x19
[92146.548582]  [<c12e591a>] ? acpi_ec_sync_query+0xa5/0xbc
[92146.548589]  [<c12e2b82>] acpi_device_notify+0x16/0x18
[92146.548595]  [<c12f4904>] acpi_ev_notify_dispatch+0x38/0x4f
[92146.548600]  [<c12df0e8>] acpi_os_execute_deferred+0x20/0x2b
[92146.548607]  [<c1051208>] process_one_work+0x128/0x3f0
[92146.548613]  [<c1564f73>] ? common_interrupt+0x33/0x38
[92146.548618]  [<c104f8c0>] ? wake_up_worker+0x30/0x30
[92146.548624]  [<c12df0c8>] ? acpi_os_wait_events_complete+0x1e/0x1e
[92146.548629]  [<c10524f9>] worker_thread+0x119/0x3b0
[92146.548634]  [<c10523e0>] ? manage_workers+0x240/0x240
[92146.548640]  [<c1056e84>] kthread+0x94/0xa0
[92146.548647]  [<c1060000>] ? ftrace_raw_output_sched_stat_runtime+0x70/0xf0
[92146.548652]  [<c15649b7>] ret_from_kernel_thread+0x1b/0x28
[92146.548658]  [<c1056df0>] ? kthread_create_on_node+0xc0/0xc0

three different modeset flags are introduced in this patch

MODESET_ON_LID: do modeset on next lid open event
MODESET_DONE:  modeset already done
MODESET_ON_RESUME:  do modeset when system is resumed

In this way,
1. when lid is closed, MODESET_ON_LID is set so that we'll do modeset on next lid open event.
2. when lid is opened, MODESET_DONE is set
so that duplicate lid open events will be ignored.
3. when system suspends, MODESET_ON_RESUME is set. In this case, we will not do modeset on any lid events.

Plus, locking mechanism is also introduced to avoid racing.

---
 drivers/gpu/drm/i915/i915_dma.c   |    1 +
 drivers/gpu/drm/i915/i915_drv.c   |   14 +++++++++-----
 drivers/gpu/drm/i915/i915_drv.h   |   11 +++++++++--
 drivers/gpu/drm/i915/intel_lvds.c |   33 ++++++++++++++++++++-------------
 4 files changed, 39 insertions(+), 20 deletions(-)
drivers/gpu/drm/i915/i915_dma.c +1 -0
index 99daa89..c7cb546 100644
@@ -1585,6 +1585,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	spin_lock_init(&dev_priv->dpio_lock);
 
 	mutex_init(&dev_priv->rps.hw_lock);
+	mutex_init(&dev_priv->modeset_lock);
 
 	if (IS_IVYBRIDGE(dev) || IS_HASWELL(dev))
 		dev_priv->num_pipe = 3;
drivers/gpu/drm/i915/i915_drv.c +9 -5
index 1172658..bd7ab5b 100644
@@ -468,6 +468,12 @@ static int i915_drm_freeze(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 
+	/* ignore lid events during suspend */
+	mutex_lock(&dev_priv->modeset_lock);
+	dev_priv->modeset = MODESET_ON_RESUME;
+	mutex_unlock(&dev_priv->modeset_lock);
+
+
 	drm_kms_helper_poll_disable(dev);
 
 	pci_save_state(dev->pdev);
@@ -492,9 +498,6 @@ static int i915_drm_freeze(struct drm_device *dev)
 
 	intel_opregion_fini(dev);
 
-	/* Modeset on resume, not lid events */
-	dev_priv->modeset_on_lid = 0;
-
 	console_lock();
 	intel_fbdev_set_suspend(dev, 1);
 	console_unlock();
@@ -569,8 +572,6 @@ static int __i915_drm_thaw(struct drm_device *dev)
 
 	intel_opregion_init(dev);
 
-	dev_priv->modeset_on_lid = 0;
-
 	/*
 	 * The console lock can be pretty contented on resume due
 	 * to all the printk activity.  Try to keep it out of the hot
@@ -583,6 +584,9 @@ static int __i915_drm_thaw(struct drm_device *dev)
 		schedule_work(&dev_priv->console_resume_work);
 	}
 
+	mutex_lock(&dev_priv->modeset_lock);
+	dev_priv->modeset = MODESET_DONE;
+	mutex_unlock(&dev_priv->modeset_lock);
 	return error;
 }
 
drivers/gpu/drm/i915/i915_drv.h +9 -2
index 12ab3bd..1a57ae8 100644
@@ -620,6 +620,12 @@ struct intel_l3_parity {
 	struct work_struct error_work;
 };
 
+enum modeset_flag {
+	MODESET_ON_LID_OPEN,
+	MODESET_DONE,
+	MODESET_ON_RESUME,
+};
+
 typedef struct drm_i915_private {
 	struct drm_device *dev;
 
@@ -750,9 +756,10 @@ typedef struct drm_i915_private {
 
 	unsigned long quirks;
 
-	/* Register state */
-	bool modeset_on_lid;
+	enum modeset_flag modeset; 
+	struct mutex modeset_lock;
 
+	/* Register state */
 	struct {
 		/** Bridge to intel-gtt-ko */
 		struct intel_gtt *gtt;
drivers/gpu/drm/i915/intel_lvds.c +20 -13
index 17aee74..4eb966a 100644
@@ -492,13 +492,14 @@ static const struct dmi_system_id intel_no_modeset_on_lid[] = {
 };
 
 /*
- * Lid events. Note the use of 'modeset_on_lid':
- *  - we set it on lid close, and reset it on open
+ * Lid events. Note the use of 'modeset':
+ *  - we set it to MODESET_ON_LID on lid close,
+ *    and set it to MODESET_DONE on open
  *  - we use it as a "only once" bit (ie we ignore
- *    duplicate events where it was already properly
- *    set/reset)
- *  - the suspend/resume paths will also set it to
- *    zero, since they restore the mode ("lid open").
+ *    duplicate events where it was already properly set)
+ *  - the suspend/resume paths will set it to
+ *    MODESET_ON_RESUME and ignore the lid open event,
+ *    because they restore the mode ("lid open").
  */
 static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 			    void *unused)
@@ -512,6 +513,9 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 	if (dev->switch_power_state != DRM_SWITCH_POWER_ON)
 		return NOTIFY_OK;
 
+	mutex_lock(&dev_priv->modeset_lock);
+	if (dev_priv->modeset == MODESET_ON_RESUME)
+		goto exit;
 	/*
 	 * check and update the status of LVDS connector after receiving
 	 * the LID nofication event.
@@ -520,21 +524,24 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 
 	/* Don't force modeset on machines where it causes a GPU lockup */
 	if (dmi_check_system(intel_no_modeset_on_lid))
-		return NOTIFY_OK;
+		goto exit;
 	if (!acpi_lid_open()) {
-		dev_priv->modeset_on_lid = 1;
-		return NOTIFY_OK;
+		/* do modeset on next lid open event */
+		dev_priv->modeset = MODESET_ON_LID_OPEN;
+		goto exit;
 	}
 
-	if (!dev_priv->modeset_on_lid)
-		return NOTIFY_OK;
-
-	dev_priv->modeset_on_lid = 0;
+	if (dev_priv->modeset == MODESET_DONE)
+		goto exit;
 
 	mutex_lock(&dev->mode_config.mutex);
 	intel_modeset_setup_hw_state(dev, true);
 	mutex_unlock(&dev->mode_config.mutex);
 
+	dev_priv->modeset = MODESET_DONE;
+
+exit:
+	mutex_unlock(&dev_priv->modeset_lock);
 	return NOTIFY_OK;
 }
 
Signature · 1 line
1.7.9.5
#3 lore raw

Re: [Intel-gfx] [PATCH V2 3/3] i915: ignore lid open event when resuming

Quoted 65 lines · Zhang Rui

i915 driver needs to do modeset when
1. system resumes from sleep
2. lid is opened

In PM_SUSPEND_MEM state, all the GPEs are cleared when system resumes, thus it is the i915_resume code does the modeset rather than intel_lid_notify().

But in PM_SUSPEND_FREEZE state, this will be broken because
system is still responsive to the lid events.
1. When we close the lid in Freeze state, intel_lid_notify() sets modeset_on_lid.
2. When we reopen the lid, intel_lid_notify() will do a modeset, before the system is resumed.
here is the error log,

[92146.548074] WARNING: at drivers/gpu/drm/i915/intel_display.c:1028 intel_wait_for_pipe_off+0x184/0x190 [i915]()
[92146.548076] Hardware name: VGN-Z540N
[92146.548078] pipe_off wait timed out
[92146.548167] Modules linked in: hid_generic usbhid hid snd_hda_codec_realtek snd_hda_intel snd_hda_codec parport_pc snd_hwdep ppdev snd_pcm_oss i915 snd_mixer_oss snd_pcm arc4 iwldvm snd_seq_dummy mac80211 snd_seq_oss snd_seq_midi fbcon tileblit font bitblit softcursor drm_kms_helper snd_rawmidi snd_seq_midi_event coretemp drm snd_seq kvm btusb bluetooth snd_timer iwlwifi pcmcia tpm_infineon i2c_algo_bit joydev snd_seq_device intel_agp cfg80211 snd intel_gtt yenta_socket pcmcia_rsrc sony_laptop agpgart microcode psmouse tpm_tis serio_raw mxm_wmi soundcore snd_page_alloc tpm acpi_cpufreq lpc_ich pcmcia_core tpm_bios mperf processor lp parport firewire_ohci firewire_core crc_itu_t sdhci_pci sdhci thermal e1000e
[92146.548173] Pid: 4304, comm: kworker/0:0 Tainted: G        W    3.8.0-rc3-s0i3-v3-test+ #9
[92146.548175] Call Trace:
[92146.548189]  [<c10378e2>] warn_slowpath_common+0x72/0xa0
[92146.548227]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548263]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548270]  [<c10379b3>] warn_slowpath_fmt+0x33/0x40
[92146.548307]  [<f86398b4>] intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548344]  [<f86399c2>] intel_disable_pipe+0x102/0x190 [i915]
[92146.548380]  [<f8639ea4>] ? intel_disable_plane+0x64/0x80 [i915]
[92146.548417]  [<f8639f7c>] i9xx_crtc_disable+0xbc/0x150 [i915]
[92146.548456]  [<f863ebee>] intel_crtc_update_dpms+0x5e/0x90 [i915]
[92146.548493]  [<f86437cf>] intel_modeset_setup_hw_state+0x42f/0x8f0 [i915]
[92146.548535]  [<f8645b0b>] intel_lid_notify+0x9b/0xc0 [i915]
[92146.548543]  [<c15610d3>] notifier_call_chain+0x43/0x60
[92146.548550]  [<c105d1e1>] __blocking_notifier_call_chain+0x41/0x80
[92146.548556]  [<c105d23f>] blocking_notifier_call_chain+0x1f/0x30
[92146.548563]  [<c131a684>] acpi_lid_send_state+0x78/0xa4
[92146.548569]  [<c131aa9e>] acpi_button_notify+0x3b/0xf1
[92146.548577]  [<c12df56a>] ? acpi_os_execute+0x17/0x19
[92146.548582]  [<c12e591a>] ? acpi_ec_sync_query+0xa5/0xbc
[92146.548589]  [<c12e2b82>] acpi_device_notify+0x16/0x18
[92146.548595]  [<c12f4904>] acpi_ev_notify_dispatch+0x38/0x4f
[92146.548600]  [<c12df0e8>] acpi_os_execute_deferred+0x20/0x2b
[92146.548607]  [<c1051208>] process_one_work+0x128/0x3f0
[92146.548613]  [<c1564f73>] ? common_interrupt+0x33/0x38
[92146.548618]  [<c104f8c0>] ? wake_up_worker+0x30/0x30
[92146.548624]  [<c12df0c8>] ? acpi_os_wait_events_complete+0x1e/0x1e
[92146.548629]  [<c10524f9>] worker_thread+0x119/0x3b0
[92146.548634]  [<c10523e0>] ? manage_workers+0x240/0x240
[92146.548640]  [<c1056e84>] kthread+0x94/0xa0
[92146.548647]  [<c1060000>] ? ftrace_raw_output_sched_stat_runtime+0x70/0xf0
[92146.548652]  [<c15649b7>] ret_from_kernel_thread+0x1b/0x28
[92146.548658]  [<c1056df0>] ? kthread_create_on_node+0xc0/0xc0

three different modeset flags are introduced in this patch

MODESET_ON_LID: do modeset on next lid open event
MODESET_DONE:  modeset already done
MODESET_ON_RESUME:  do modeset when system is resumed

In this way,
1. when lid is closed, MODESET_ON_LID is set so that we'll do modeset on next lid open event.
2. when lid is opened, MODESET_DONE is set
so that duplicate lid open events will be ignored.
3. when system suspends, MODESET_ON_RESUME is set. In this case, we will not do modeset on any lid events.

Quoted 3 lines

Plus, locking mechanism is also introduced to avoid racing.

Looks nice, two tiny bikesheds below.

Quoted 24 lines
---
 drivers/gpu/drm/i915/i915_dma.c   |    1 +
 drivers/gpu/drm/i915/i915_drv.c   |   14 +++++++++-----
 drivers/gpu/drm/i915/i915_drv.h   |   11 +++++++++--
 drivers/gpu/drm/i915/intel_lvds.c |   33 ++++++++++++++++++++-------------
 4 files changed, 39 insertions(+), 20 deletions(-)
drivers/gpu/drm/i915/i915_dma.c +1 -0
index 99daa89..c7cb546 100644
@@ -1585,6 +1585,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	spin_lock_init(&dev_priv->dpio_lock);
 
 	mutex_init(&dev_priv->rps.hw_lock);
+	mutex_init(&dev_priv->modeset_lock);
 
 	if (IS_IVYBRIDGE(dev) || IS_HASWELL(dev))
 		dev_priv->num_pipe = 3;
drivers/gpu/drm/i915/i915_drv.c +0 -0
index 1172658..bd7ab5b 100644

drivers/gpu/drm/i915/i915_drv.c static int i915_drm_freeze(struct drm_device *dev) · line 473

Quoted 6 lines
drivers/gpu/drm/i915/i915_drv.c +3 -0
@@ -468,6 +468,12 @@ static int i915_drm_freeze(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 
+	/* ignore lid events during suspend */
+	mutex_lock(&dev_priv->modeset_lock);
+	dev_priv->modeset = MODESET_ON_RESUME;

I think calling this MODESET_SUSPENDED would make it clearer that we have disable the modeset (and so lid restore) handling.

Quoted 53 lines
drivers/gpu/drm/i915/i915_drv.c +6 -5
+	mutex_unlock(&dev_priv->modeset_lock);
+
+
 	drm_kms_helper_poll_disable(dev);
 
 	pci_save_state(dev->pdev);
@@ -492,9 +498,6 @@ static int i915_drm_freeze(struct drm_device *dev)
 
 	intel_opregion_fini(dev);
 
-	/* Modeset on resume, not lid events */
-	dev_priv->modeset_on_lid = 0;
-
 	console_lock();
 	intel_fbdev_set_suspend(dev, 1);
 	console_unlock();
@@ -569,8 +572,6 @@ static int __i915_drm_thaw(struct drm_device *dev)
 
 	intel_opregion_init(dev);
 
-	dev_priv->modeset_on_lid = 0;
-
 	/*
 	 * The console lock can be pretty contented on resume due
 	 * to all the printk activity.  Try to keep it out of the hot
@@ -583,6 +584,9 @@ static int __i915_drm_thaw(struct drm_device *dev)
 		schedule_work(&dev_priv->console_resume_work);
 	}
 
+	mutex_lock(&dev_priv->modeset_lock);
+	dev_priv->modeset = MODESET_DONE;
+	mutex_unlock(&dev_priv->modeset_lock);
 	return error;
 }
 
drivers/gpu/drm/i915/i915_drv.h +6 -0
index 12ab3bd..1a57ae8 100644
@@ -620,6 +620,12 @@ struct intel_l3_parity {
 	struct work_struct error_work;
 };
 
+enum modeset_flag {
+	MODESET_ON_LID_OPEN,
+	MODESET_DONE,
+	MODESET_ON_RESUME,
+};
+
 typedef struct drm_i915_private {
 	struct drm_device *dev;
 

drivers/gpu/drm/i915/i915_drv.h typedef struct drm_i915_private { · line 760

Quoted 7 lines
drivers/gpu/drm/i915/i915_drv.h +2 -2
@@ -750,9 +756,10 @@ typedef struct drm_i915_private {
 
 	unsigned long quirks;
 
-	/* Register state */
-	bool modeset_on_lid;
+	enum modeset_flag modeset; 
+	struct mutex modeset_lock;

Using modeset/modeset_lock is imo a bit too generic, since this is all about restoring the modeset configuration on lid open. What about

- bool modeset_on_lid;
+ enum modeset_restore modeset_restore;
+ struct mutex modeset_restore_lock;

instead?

Yours, Daniel

Quoted 79 lines
drivers/gpu/drm/i915/i915_drv.h +1 -0
+	/* Register state */
 	struct {
 		/** Bridge to intel-gtt-ko */
 		struct intel_gtt *gtt;
drivers/gpu/drm/i915/intel_lvds.c +20 -13
index 17aee74..4eb966a 100644
@@ -492,13 +492,14 @@ static const struct dmi_system_id intel_no_modeset_on_lid[] = {
 };
 
 /*
- * Lid events. Note the use of 'modeset_on_lid':
- *  - we set it on lid close, and reset it on open
+ * Lid events. Note the use of 'modeset':
+ *  - we set it to MODESET_ON_LID on lid close,
+ *    and set it to MODESET_DONE on open
  *  - we use it as a "only once" bit (ie we ignore
- *    duplicate events where it was already properly
- *    set/reset)
- *  - the suspend/resume paths will also set it to
- *    zero, since they restore the mode ("lid open").
+ *    duplicate events where it was already properly set)
+ *  - the suspend/resume paths will set it to
+ *    MODESET_ON_RESUME and ignore the lid open event,
+ *    because they restore the mode ("lid open").
  */
 static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 			    void *unused)
@@ -512,6 +513,9 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 	if (dev->switch_power_state != DRM_SWITCH_POWER_ON)
 		return NOTIFY_OK;
 
+	mutex_lock(&dev_priv->modeset_lock);
+	if (dev_priv->modeset == MODESET_ON_RESUME)
+		goto exit;
 	/*
 	 * check and update the status of LVDS connector after receiving
 	 * the LID nofication event.
@@ -520,21 +524,24 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 
 	/* Don't force modeset on machines where it causes a GPU lockup */
 	if (dmi_check_system(intel_no_modeset_on_lid))
-		return NOTIFY_OK;
+		goto exit;
 	if (!acpi_lid_open()) {
-		dev_priv->modeset_on_lid = 1;
-		return NOTIFY_OK;
+		/* do modeset on next lid open event */
+		dev_priv->modeset = MODESET_ON_LID_OPEN;
+		goto exit;
 	}
 
-	if (!dev_priv->modeset_on_lid)
-		return NOTIFY_OK;
-
-	dev_priv->modeset_on_lid = 0;
+	if (dev_priv->modeset == MODESET_DONE)
+		goto exit;
 
 	mutex_lock(&dev->mode_config.mutex);
 	intel_modeset_setup_hw_state(dev, true);
 	mutex_unlock(&dev->mode_config.mutex);
 
+	dev_priv->modeset = MODESET_DONE;
+
+exit:
+	mutex_unlock(&dev_priv->modeset_lock);
 	return NOTIFY_OK;
 }
 
Signature · 6 lines
1.7.9.5

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 3 lines
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch
author
#4 lore raw

Re: [Intel-gfx] [PATCH V2 3/3] i915: ignore lid open event when resuming

Quoted 66 lines · Daniel Vetter
Quoted 65 lines · Zhang Rui

i915 driver needs to do modeset when
1. system resumes from sleep
2. lid is opened

In PM_SUSPEND_MEM state, all the GPEs are cleared when system resumes, thus it is the i915_resume code does the modeset rather than intel_lid_notify().

But in PM_SUSPEND_FREEZE state, this will be broken because
system is still responsive to the lid events.
1. When we close the lid in Freeze state, intel_lid_notify() sets modeset_on_lid.
2. When we reopen the lid, intel_lid_notify() will do a modeset, before the system is resumed.
here is the error log,

[92146.548074] WARNING: at drivers/gpu/drm/i915/intel_display.c:1028 intel_wait_for_pipe_off+0x184/0x190 [i915]()
[92146.548076] Hardware name: VGN-Z540N
[92146.548078] pipe_off wait timed out
[92146.548167] Modules linked in: hid_generic usbhid hid snd_hda_codec_realtek snd_hda_intel snd_hda_codec parport_pc snd_hwdep ppdev snd_pcm_oss i915 snd_mixer_oss snd_pcm arc4 iwldvm snd_seq_dummy mac80211 snd_seq_oss snd_seq_midi fbcon tileblit font bitblit softcursor drm_kms_helper snd_rawmidi snd_seq_midi_event coretemp drm snd_seq kvm btusb bluetooth snd_timer iwlwifi pcmcia tpm_infineon i2c_algo_bit joydev snd_seq_device intel_agp cfg80211 snd intel_gtt yenta_socket pcmcia_rsrc sony_laptop agpgart microcode psmouse tpm_tis serio_raw mxm_wmi soundcore snd_page_alloc tpm acpi_cpufreq lpc_ich pcmcia_core tpm_bios mperf processor lp parport firewire_ohci firewire_core crc_itu_t sdhci_pci sdhci thermal e1000e
[92146.548173] Pid: 4304, comm: kworker/0:0 Tainted: G        W    3.8.0-rc3-s0i3-v3-test+ #9
[92146.548175] Call Trace:
[92146.548189]  [<c10378e2>] warn_slowpath_common+0x72/0xa0
[92146.548227]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548263]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548270]  [<c10379b3>] warn_slowpath_fmt+0x33/0x40
[92146.548307]  [<f86398b4>] intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548344]  [<f86399c2>] intel_disable_pipe+0x102/0x190 [i915]
[92146.548380]  [<f8639ea4>] ? intel_disable_plane+0x64/0x80 [i915]
[92146.548417]  [<f8639f7c>] i9xx_crtc_disable+0xbc/0x150 [i915]
[92146.548456]  [<f863ebee>] intel_crtc_update_dpms+0x5e/0x90 [i915]
[92146.548493]  [<f86437cf>] intel_modeset_setup_hw_state+0x42f/0x8f0 [i915]
[92146.548535]  [<f8645b0b>] intel_lid_notify+0x9b/0xc0 [i915]
[92146.548543]  [<c15610d3>] notifier_call_chain+0x43/0x60
[92146.548550]  [<c105d1e1>] __blocking_notifier_call_chain+0x41/0x80
[92146.548556]  [<c105d23f>] blocking_notifier_call_chain+0x1f/0x30
[92146.548563]  [<c131a684>] acpi_lid_send_state+0x78/0xa4
[92146.548569]  [<c131aa9e>] acpi_button_notify+0x3b/0xf1
[92146.548577]  [<c12df56a>] ? acpi_os_execute+0x17/0x19
[92146.548582]  [<c12e591a>] ? acpi_ec_sync_query+0xa5/0xbc
[92146.548589]  [<c12e2b82>] acpi_device_notify+0x16/0x18
[92146.548595]  [<c12f4904>] acpi_ev_notify_dispatch+0x38/0x4f
[92146.548600]  [<c12df0e8>] acpi_os_execute_deferred+0x20/0x2b
[92146.548607]  [<c1051208>] process_one_work+0x128/0x3f0
[92146.548613]  [<c1564f73>] ? common_interrupt+0x33/0x38
[92146.548618]  [<c104f8c0>] ? wake_up_worker+0x30/0x30
[92146.548624]  [<c12df0c8>] ? acpi_os_wait_events_complete+0x1e/0x1e
[92146.548629]  [<c10524f9>] worker_thread+0x119/0x3b0
[92146.548634]  [<c10523e0>] ? manage_workers+0x240/0x240
[92146.548640]  [<c1056e84>] kthread+0x94/0xa0
[92146.548647]  [<c1060000>] ? ftrace_raw_output_sched_stat_runtime+0x70/0xf0
[92146.548652]  [<c15649b7>] ret_from_kernel_thread+0x1b/0x28
[92146.548658]  [<c1056df0>] ? kthread_create_on_node+0xc0/0xc0

three different modeset flags are introduced in this patch

MODESET_ON_LID: do modeset on next lid open event
MODESET_DONE:  modeset already done
MODESET_ON_RESUME:  do modeset when system is resumed

In this way,
1. when lid is closed, MODESET_ON_LID is set so that we'll do modeset on next lid open event.
2. when lid is opened, MODESET_DONE is set
so that duplicate lid open events will be ignored.
3. when system suspends, MODESET_ON_RESUME is set. In this case, we will not do modeset on any lid events.

Quoted 6 lines
Quoted 3 lines

Plus, locking mechanism is also introduced to avoid racing.

Looks nice, two tiny bikesheds below.

Great, thanks for reviewing. Refreshed patch attached.

Quoted 1 line

From 0d597b4859535c79ed545160cf4af9e6b5970e3c Mon Sep 17 00:00:00 2001

From: Zhang Rui <[email protected]>
Date: Thu, 24 Jan 2013 13:27:22 +0800
Subject: [PATCH V3 3/3] i915: ignore lid open event when resuming

i915 driver needs to do modeset when
1. system resumes from sleep
2. lid is opened

In PM_SUSPEND_MEM state, all the GPEs are cleared when system resumes, thus it is the i915_resume code does the modeset rather than intel_lid_notify().

But in PM_SUSPEND_FREEZE state, this will be broken because
system is still responsive to the lid events.
1. When we close the lid in Freeze state, intel_lid_notify() sets modeset_on_lid.
2. When we reopen the lid, intel_lid_notify() will do a modeset, before the system is resumed.
here is the error log,

[92146.548074] WARNING: at drivers/gpu/drm/i915/intel_display.c:1028 intel_wait_for_pipe_off+0x184/0x190 [i915]()
[92146.548076] Hardware name: VGN-Z540N
[92146.548078] pipe_off wait timed out
[92146.548167] Modules linked in: hid_generic usbhid hid snd_hda_codec_realtek snd_hda_intel snd_hda_codec parport_pc snd_hwdep ppdev snd_pcm_oss i915 snd_mixer_oss snd_pcm arc4 iwldvm snd_seq_dummy mac80211 snd_seq_oss snd_seq_midi fbcon tileblit font bitblit softcursor drm_kms_helper snd_rawmidi snd_seq_midi_event coretemp drm snd_seq kvm btusb bluetooth snd_timer iwlwifi pcmcia tpm_infineon i2c_algo_bit joydev snd_seq_device intel_agp cfg80211 snd intel_gtt yenta_socket pcmcia_rsrc sony_laptop agpgart microcode psmouse tpm_tis serio_raw mxm_wmi soundcore snd_page_alloc tpm acpi_cpufreq lpc_ich pcmcia_core tpm_bios mperf processor lp parport firewire_ohci firewire_core crc_itu_t sdhci_pci sdhci thermal e1000e
[92146.548173] Pid: 4304, comm: kworker/0:0 Tainted: G        W    3.8.0-rc3-s0i3-v3-test+ #9
[92146.548175] Call Trace:
[92146.548189]  [<c10378e2>] warn_slowpath_common+0x72/0xa0
[92146.548227]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548263]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548270]  [<c10379b3>] warn_slowpath_fmt+0x33/0x40
[92146.548307]  [<f86398b4>] intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548344]  [<f86399c2>] intel_disable_pipe+0x102/0x190 [i915]
[92146.548380]  [<f8639ea4>] ? intel_disable_plane+0x64/0x80 [i915]
[92146.548417]  [<f8639f7c>] i9xx_crtc_disable+0xbc/0x150 [i915]
[92146.548456]  [<f863ebee>] intel_crtc_update_dpms+0x5e/0x90 [i915]
[92146.548493]  [<f86437cf>] intel_modeset_setup_hw_state+0x42f/0x8f0 [i915]
[92146.548535]  [<f8645b0b>] intel_lid_notify+0x9b/0xc0 [i915]
[92146.548543]  [<c15610d3>] notifier_call_chain+0x43/0x60
[92146.548550]  [<c105d1e1>] __blocking_notifier_call_chain+0x41/0x80
[92146.548556]  [<c105d23f>] blocking_notifier_call_chain+0x1f/0x30
[92146.548563]  [<c131a684>] acpi_lid_send_state+0x78/0xa4
[92146.548569]  [<c131aa9e>] acpi_button_notify+0x3b/0xf1
[92146.548577]  [<c12df56a>] ? acpi_os_execute+0x17/0x19
[92146.548582]  [<c12e591a>] ? acpi_ec_sync_query+0xa5/0xbc
[92146.548589]  [<c12e2b82>] acpi_device_notify+0x16/0x18
[92146.548595]  [<c12f4904>] acpi_ev_notify_dispatch+0x38/0x4f
[92146.548600]  [<c12df0e8>] acpi_os_execute_deferred+0x20/0x2b
[92146.548607]  [<c1051208>] process_one_work+0x128/0x3f0
[92146.548613]  [<c1564f73>] ? common_interrupt+0x33/0x38
[92146.548618]  [<c104f8c0>] ? wake_up_worker+0x30/0x30
[92146.548624]  [<c12df0c8>] ? acpi_os_wait_events_complete+0x1e/0x1e
[92146.548629]  [<c10524f9>] worker_thread+0x119/0x3b0
[92146.548634]  [<c10523e0>] ? manage_workers+0x240/0x240
[92146.548640]  [<c1056e84>] kthread+0x94/0xa0
[92146.548647]  [<c1060000>] ? ftrace_raw_output_sched_stat_runtime+0x70/0xf0
[92146.548652]  [<c15649b7>] ret_from_kernel_thread+0x1b/0x28
[92146.548658]  [<c1056df0>] ? kthread_create_on_node+0xc0/0xc0

three different modeset flags are introduced in this patch

MODESET_ON_LID: do modeset on next lid open event
MODESET_DONE:  modeset already done
MODESET_ON_RESUME:  do modeset when system is resumed

In this way,
1. when lid is closed, MODESET_ON_LID is set so that we'll do modeset on next lid open event.
2. when lid is opened, MODESET_DONE is set
so that duplicate lid open events will be ignored.
3. when system suspends, MODESET_ON_RESUME is set. In this case, we will not do modeset on any lid events.

Plus, locking mechanism is also introduced to avoid racing.

---
 drivers/gpu/drm/i915/i915_dma.c   |    1 +
 drivers/gpu/drm/i915/i915_drv.c   |   14 +++++++++-----
 drivers/gpu/drm/i915/i915_drv.h   |   11 +++++++++--
 drivers/gpu/drm/i915/intel_lvds.c |   33 ++++++++++++++++++++-------------
 4 files changed, 39 insertions(+), 20 deletions(-)
drivers/gpu/drm/i915/i915_dma.c +1 -0
index 99daa89..a5115d8 100644
@@ -1585,6 +1585,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	spin_lock_init(&dev_priv->dpio_lock);
 
 	mutex_init(&dev_priv->rps.hw_lock);
+	mutex_init(&dev_priv->modeset_restore_lock);
 
 	if (IS_IVYBRIDGE(dev) || IS_HASWELL(dev))
 		dev_priv->num_pipe = 3;
drivers/gpu/drm/i915/i915_drv.c +9 -5
index 1172658..68c6048 100644
@@ -468,6 +468,12 @@ static int i915_drm_freeze(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 
+	/* ignore lid events during suspend */
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	dev_priv->modeset_restore = MODESET_SUSPENDED;
+	mutex_unlock(&dev_priv->modeset_restore_lock);
+
+
 	drm_kms_helper_poll_disable(dev);
 
 	pci_save_state(dev->pdev);
@@ -492,9 +498,6 @@ static int i915_drm_freeze(struct drm_device *dev)
 
 	intel_opregion_fini(dev);
 
-	/* Modeset on resume, not lid events */
-	dev_priv->modeset_on_lid = 0;
-
 	console_lock();
 	intel_fbdev_set_suspend(dev, 1);
 	console_unlock();
@@ -569,8 +572,6 @@ static int __i915_drm_thaw(struct drm_device *dev)
 
 	intel_opregion_init(dev);
 
-	dev_priv->modeset_on_lid = 0;
-
 	/*
 	 * The console lock can be pretty contented on resume due
 	 * to all the printk activity.  Try to keep it out of the hot
@@ -583,6 +584,9 @@ static int __i915_drm_thaw(struct drm_device *dev)
 		schedule_work(&dev_priv->console_resume_work);
 	}
 
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	dev_priv->modeset_restore = MODESET_DONE;
+	mutex_unlock(&dev_priv->modeset_restore_lock);
 	return error;
 }
 
drivers/gpu/drm/i915/i915_drv.h +9 -2
index 12ab3bd..0fddad01 100644
@@ -620,6 +620,12 @@ struct intel_l3_parity {
 	struct work_struct error_work;
 };
 
+enum modeset_restore {
+	MODESET_ON_LID_OPEN,
+	MODESET_DONE,
+	MODESET_SUSPENDED,
+};
+
 typedef struct drm_i915_private {
 	struct drm_device *dev;
 
@@ -750,9 +756,10 @@ typedef struct drm_i915_private {
 
 	unsigned long quirks;
 
-	/* Register state */
-	bool modeset_on_lid;
+	enum modeset_restore modeset_restore; 
+	struct mutex modeset_restore_lock;
 
+	/* Register state */
 	struct {
 		/** Bridge to intel-gtt-ko */
 		struct intel_gtt *gtt;
drivers/gpu/drm/i915/intel_lvds.c +20 -13
index 17aee74..2f55e9c 100644
@@ -492,13 +492,14 @@ static const struct dmi_system_id intel_no_modeset_on_lid[] = {
 };
 
 /*
- * Lid events. Note the use of 'modeset_on_lid':
- *  - we set it on lid close, and reset it on open
+ * Lid events. Note the use of 'modeset':
+ *  - we set it to MODESET_ON_LID on lid close,
+ *    and set it to MODESET_DONE on open
  *  - we use it as a "only once" bit (ie we ignore
- *    duplicate events where it was already properly
- *    set/reset)
- *  - the suspend/resume paths will also set it to
- *    zero, since they restore the mode ("lid open").
+ *    duplicate events where it was already properly set)
+ *  - the suspend/resume paths will set it to
+ *    MODESET_ON_RESUME and ignore the lid open event,
+ *    because they restore the mode ("lid open").
  */
 static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 			    void *unused)
@@ -512,6 +513,9 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 	if (dev->switch_power_state != DRM_SWITCH_POWER_ON)
 		return NOTIFY_OK;
 
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	if (dev_priv->modeset_restore == MODESET_SUSPENDED)
+		goto exit;
 	/*
 	 * check and update the status of LVDS connector after receiving
 	 * the LID nofication event.
@@ -520,21 +524,24 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 
 	/* Don't force modeset on machines where it causes a GPU lockup */
 	if (dmi_check_system(intel_no_modeset_on_lid))
-		return NOTIFY_OK;
+		goto exit;
 	if (!acpi_lid_open()) {
-		dev_priv->modeset_on_lid = 1;
-		return NOTIFY_OK;
+		/* do modeset on next lid open event */
+		dev_priv->modeset_restore = MODESET_ON_LID_OPEN;
+		goto exit;
 	}
 
-	if (!dev_priv->modeset_on_lid)
-		return NOTIFY_OK;
-
-	dev_priv->modeset_on_lid = 0;
+	if (dev_priv->modeset_restore == MODESET_DONE)
+		goto exit;
 
 	mutex_lock(&dev->mode_config.mutex);
 	intel_modeset_setup_hw_state(dev, true);
 	mutex_unlock(&dev->mode_config.mutex);
 
+	dev_priv->modeset_restore = MODESET_DONE;
+
+exit:
+	mutex_unlock(&dev_priv->modeset_restore_lock);
 	return NOTIFY_OK;
 }
 
Signature · 1 line
1.7.9.5
author
#5 lore raw

Re: [Intel-gfx] [PATCH V2 3/3] i915: ignore lid open event when resuming

Quoted 67 lines · Zhang Rui
Quoted 66 lines · Daniel Vetter
Quoted 65 lines · Zhang Rui

i915 driver needs to do modeset when
1. system resumes from sleep
2. lid is opened

In PM_SUSPEND_MEM state, all the GPEs are cleared when system resumes, thus it is the i915_resume code does the modeset rather than intel_lid_notify().

But in PM_SUSPEND_FREEZE state, this will be broken because
system is still responsive to the lid events.
1. When we close the lid in Freeze state, intel_lid_notify() sets modeset_on_lid.
2. When we reopen the lid, intel_lid_notify() will do a modeset, before the system is resumed.
here is the error log,

[92146.548074] WARNING: at drivers/gpu/drm/i915/intel_display.c:1028 intel_wait_for_pipe_off+0x184/0x190 [i915]()
[92146.548076] Hardware name: VGN-Z540N
[92146.548078] pipe_off wait timed out
[92146.548167] Modules linked in: hid_generic usbhid hid snd_hda_codec_realtek snd_hda_intel snd_hda_codec parport_pc snd_hwdep ppdev snd_pcm_oss i915 snd_mixer_oss snd_pcm arc4 iwldvm snd_seq_dummy mac80211 snd_seq_oss snd_seq_midi fbcon tileblit font bitblit softcursor drm_kms_helper snd_rawmidi snd_seq_midi_event coretemp drm snd_seq kvm btusb bluetooth snd_timer iwlwifi pcmcia tpm_infineon i2c_algo_bit joydev snd_seq_device intel_agp cfg80211 snd intel_gtt yenta_socket pcmcia_rsrc sony_laptop agpgart microcode psmouse tpm_tis serio_raw mxm_wmi soundcore snd_page_alloc tpm acpi_cpufreq lpc_ich pcmcia_core tpm_bios mperf processor lp parport firewire_ohci firewire_core crc_itu_t sdhci_pci sdhci thermal e1000e
[92146.548173] Pid: 4304, comm: kworker/0:0 Tainted: G        W    3.8.0-rc3-s0i3-v3-test+ #9
[92146.548175] Call Trace:
[92146.548189]  [<c10378e2>] warn_slowpath_common+0x72/0xa0
[92146.548227]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548263]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548270]  [<c10379b3>] warn_slowpath_fmt+0x33/0x40
[92146.548307]  [<f86398b4>] intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548344]  [<f86399c2>] intel_disable_pipe+0x102/0x190 [i915]
[92146.548380]  [<f8639ea4>] ? intel_disable_plane+0x64/0x80 [i915]
[92146.548417]  [<f8639f7c>] i9xx_crtc_disable+0xbc/0x150 [i915]
[92146.548456]  [<f863ebee>] intel_crtc_update_dpms+0x5e/0x90 [i915]
[92146.548493]  [<f86437cf>] intel_modeset_setup_hw_state+0x42f/0x8f0 [i915]
[92146.548535]  [<f8645b0b>] intel_lid_notify+0x9b/0xc0 [i915]
[92146.548543]  [<c15610d3>] notifier_call_chain+0x43/0x60
[92146.548550]  [<c105d1e1>] __blocking_notifier_call_chain+0x41/0x80
[92146.548556]  [<c105d23f>] blocking_notifier_call_chain+0x1f/0x30
[92146.548563]  [<c131a684>] acpi_lid_send_state+0x78/0xa4
[92146.548569]  [<c131aa9e>] acpi_button_notify+0x3b/0xf1
[92146.548577]  [<c12df56a>] ? acpi_os_execute+0x17/0x19
[92146.548582]  [<c12e591a>] ? acpi_ec_sync_query+0xa5/0xbc
[92146.548589]  [<c12e2b82>] acpi_device_notify+0x16/0x18
[92146.548595]  [<c12f4904>] acpi_ev_notify_dispatch+0x38/0x4f
[92146.548600]  [<c12df0e8>] acpi_os_execute_deferred+0x20/0x2b
[92146.548607]  [<c1051208>] process_one_work+0x128/0x3f0
[92146.548613]  [<c1564f73>] ? common_interrupt+0x33/0x38
[92146.548618]  [<c104f8c0>] ? wake_up_worker+0x30/0x30
[92146.548624]  [<c12df0c8>] ? acpi_os_wait_events_complete+0x1e/0x1e
[92146.548629]  [<c10524f9>] worker_thread+0x119/0x3b0
[92146.548634]  [<c10523e0>] ? manage_workers+0x240/0x240
[92146.548640]  [<c1056e84>] kthread+0x94/0xa0
[92146.548647]  [<c1060000>] ? ftrace_raw_output_sched_stat_runtime+0x70/0xf0
[92146.548652]  [<c15649b7>] ret_from_kernel_thread+0x1b/0x28
[92146.548658]  [<c1056df0>] ? kthread_create_on_node+0xc0/0xc0

three different modeset flags are introduced in this patch

MODESET_ON_LID: do modeset on next lid open event
MODESET_DONE:  modeset already done
MODESET_ON_RESUME:  do modeset when system is resumed

In this way,
1. when lid is closed, MODESET_ON_LID is set so that we'll do modeset on next lid open event.
2. when lid is opened, MODESET_DONE is set
so that duplicate lid open events will be ignored.
3. when system suspends, MODESET_ON_RESUME is set. In this case, we will not do modeset on any lid events.

Quoted 7 lines
Quoted 6 lines
Quoted 3 lines

Plus, locking mechanism is also introduced to avoid racing.

Looks nice, two tiny bikesheds below.

Great, thanks for reviewing. Refreshed patch attached.

oops, forgot to update the changelog and comments. refreshed patch attached.

Quoted 1 line

From b584fcebb6d715a317f192c88606b875ee88ce78 Mon Sep 17 00:00:00 2001

From: Zhang Rui <[email protected]>
Date: Thu, 24 Jan 2013 13:27:22 +0800
Subject: [PATCH V3 3/3] i915: ignore lid open event when resuming

i915 driver needs to do modeset when
1. system resumes from sleep
2. lid is opened

In PM_SUSPEND_MEM state, all the GPEs are cleared when system resumes, thus it is the i915_resume code does the modeset rather than intel_lid_notify().

But in PM_SUSPEND_FREEZE state, this will be broken because
system is still responsive to the lid events.
1. When we close the lid in Freeze state, intel_lid_notify() sets modeset_on_lid.
2. When we reopen the lid, intel_lid_notify() will do a modeset, before the system is resumed.
here is the error log,

[92146.548074] WARNING: at drivers/gpu/drm/i915/intel_display.c:1028 intel_wait_for_pipe_off+0x184/0x190 [i915]()
[92146.548076] Hardware name: VGN-Z540N
[92146.548078] pipe_off wait timed out
[92146.548167] Modules linked in: hid_generic usbhid hid snd_hda_codec_realtek snd_hda_intel snd_hda_codec parport_pc snd_hwdep ppdev snd_pcm_oss i915 snd_mixer_oss snd_pcm arc4 iwldvm snd_seq_dummy mac80211 snd_seq_oss snd_seq_midi fbcon tileblit font bitblit softcursor drm_kms_helper snd_rawmidi snd_seq_midi_event coretemp drm snd_seq kvm btusb bluetooth snd_timer iwlwifi pcmcia tpm_infineon i2c_algo_bit joydev snd_seq_device intel_agp cfg80211 snd intel_gtt yenta_socket pcmcia_rsrc sony_laptop agpgart microcode psmouse tpm_tis serio_raw mxm_wmi soundcore snd_page_alloc tpm acpi_cpufreq lpc_ich pcmcia_core tpm_bios mperf processor lp parport firewire_ohci firewire_core crc_itu_t sdhci_pci sdhci thermal e1000e
[92146.548173] Pid: 4304, comm: kworker/0:0 Tainted: G        W    3.8.0-rc3-s0i3-v3-test+ #9
[92146.548175] Call Trace:
[92146.548189]  [<c10378e2>] warn_slowpath_common+0x72/0xa0
[92146.548227]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548263]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548270]  [<c10379b3>] warn_slowpath_fmt+0x33/0x40
[92146.548307]  [<f86398b4>] intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548344]  [<f86399c2>] intel_disable_pipe+0x102/0x190 [i915]
[92146.548380]  [<f8639ea4>] ? intel_disable_plane+0x64/0x80 [i915]
[92146.548417]  [<f8639f7c>] i9xx_crtc_disable+0xbc/0x150 [i915]
[92146.548456]  [<f863ebee>] intel_crtc_update_dpms+0x5e/0x90 [i915]
[92146.548493]  [<f86437cf>] intel_modeset_setup_hw_state+0x42f/0x8f0 [i915]
[92146.548535]  [<f8645b0b>] intel_lid_notify+0x9b/0xc0 [i915]
[92146.548543]  [<c15610d3>] notifier_call_chain+0x43/0x60
[92146.548550]  [<c105d1e1>] __blocking_notifier_call_chain+0x41/0x80
[92146.548556]  [<c105d23f>] blocking_notifier_call_chain+0x1f/0x30
[92146.548563]  [<c131a684>] acpi_lid_send_state+0x78/0xa4
[92146.548569]  [<c131aa9e>] acpi_button_notify+0x3b/0xf1
[92146.548577]  [<c12df56a>] ? acpi_os_execute+0x17/0x19
[92146.548582]  [<c12e591a>] ? acpi_ec_sync_query+0xa5/0xbc
[92146.548589]  [<c12e2b82>] acpi_device_notify+0x16/0x18
[92146.548595]  [<c12f4904>] acpi_ev_notify_dispatch+0x38/0x4f
[92146.548600]  [<c12df0e8>] acpi_os_execute_deferred+0x20/0x2b
[92146.548607]  [<c1051208>] process_one_work+0x128/0x3f0
[92146.548613]  [<c1564f73>] ? common_interrupt+0x33/0x38
[92146.548618]  [<c104f8c0>] ? wake_up_worker+0x30/0x30
[92146.548624]  [<c12df0c8>] ? acpi_os_wait_events_complete+0x1e/0x1e
[92146.548629]  [<c10524f9>] worker_thread+0x119/0x3b0
[92146.548634]  [<c10523e0>] ? manage_workers+0x240/0x240
[92146.548640]  [<c1056e84>] kthread+0x94/0xa0
[92146.548647]  [<c1060000>] ? ftrace_raw_output_sched_stat_runtime+0x70/0xf0
[92146.548652]  [<c15649b7>] ret_from_kernel_thread+0x1b/0x28
[92146.548658]  [<c1056df0>] ? kthread_create_on_node+0xc0/0xc0

three different modeset flags are introduced in this patch

MODESET_ON_LID_OPEN: do modeset on next lid open event
MODESET_DONE:  modeset already done
MODESET_SUSPENDED:  suspended, only do modeset when system is resumed

In this way,
1. when lid is closed, MODESET_ON_LID_OPEN is set so that we'll do modeset on next lid open event.
2. when lid is opened, MODESET_DONE is set
so that duplicate lid open events will be ignored.
3. when system suspends, MODESET_SUSPENDED is set. In this case, we will not do modeset on any lid events.

Plus, locking mechanism is also introduced to avoid racing.

---
 drivers/gpu/drm/i915/i915_dma.c   |    1 +
 drivers/gpu/drm/i915/i915_drv.c   |   14 +++++++++-----
 drivers/gpu/drm/i915/i915_drv.h   |   11 +++++++++--
 drivers/gpu/drm/i915/intel_lvds.c |   33 ++++++++++++++++++++-------------
 4 files changed, 39 insertions(+), 20 deletions(-)
drivers/gpu/drm/i915/i915_dma.c +1 -0
index 99daa89..a5115d8 100644
@@ -1585,6 +1585,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	spin_lock_init(&dev_priv->dpio_lock);
 
 	mutex_init(&dev_priv->rps.hw_lock);
+	mutex_init(&dev_priv->modeset_restore_lock);
 
 	if (IS_IVYBRIDGE(dev) || IS_HASWELL(dev))
 		dev_priv->num_pipe = 3;
drivers/gpu/drm/i915/i915_drv.c +9 -5
index 1172658..68c6048 100644
@@ -468,6 +468,12 @@ static int i915_drm_freeze(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 
+	/* ignore lid events during suspend */
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	dev_priv->modeset_restore = MODESET_SUSPENDED;
+	mutex_unlock(&dev_priv->modeset_restore_lock);
+
+
 	drm_kms_helper_poll_disable(dev);
 
 	pci_save_state(dev->pdev);
@@ -492,9 +498,6 @@ static int i915_drm_freeze(struct drm_device *dev)
 
 	intel_opregion_fini(dev);
 
-	/* Modeset on resume, not lid events */
-	dev_priv->modeset_on_lid = 0;
-
 	console_lock();
 	intel_fbdev_set_suspend(dev, 1);
 	console_unlock();
@@ -569,8 +572,6 @@ static int __i915_drm_thaw(struct drm_device *dev)
 
 	intel_opregion_init(dev);
 
-	dev_priv->modeset_on_lid = 0;
-
 	/*
 	 * The console lock can be pretty contented on resume due
 	 * to all the printk activity.  Try to keep it out of the hot
@@ -583,6 +584,9 @@ static int __i915_drm_thaw(struct drm_device *dev)
 		schedule_work(&dev_priv->console_resume_work);
 	}
 
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	dev_priv->modeset_restore = MODESET_DONE;
+	mutex_unlock(&dev_priv->modeset_restore_lock);
 	return error;
 }
 
drivers/gpu/drm/i915/i915_drv.h +9 -2
index 12ab3bd..0fddad01 100644
@@ -620,6 +620,12 @@ struct intel_l3_parity {
 	struct work_struct error_work;
 };
 
+enum modeset_restore {
+	MODESET_ON_LID_OPEN,
+	MODESET_DONE,
+	MODESET_SUSPENDED,
+};
+
 typedef struct drm_i915_private {
 	struct drm_device *dev;
 
@@ -750,9 +756,10 @@ typedef struct drm_i915_private {
 
 	unsigned long quirks;
 
-	/* Register state */
-	bool modeset_on_lid;
+	enum modeset_restore modeset_restore; 
+	struct mutex modeset_restore_lock;
 
+	/* Register state */
 	struct {
 		/** Bridge to intel-gtt-ko */
 		struct intel_gtt *gtt;
drivers/gpu/drm/i915/intel_lvds.c +20 -13
index 17aee74..ff89d58 100644
@@ -492,13 +492,14 @@ static const struct dmi_system_id intel_no_modeset_on_lid[] = {
 };
 
 /*
- * Lid events. Note the use of 'modeset_on_lid':
- *  - we set it on lid close, and reset it on open
+ * Lid events. Note the use of 'modeset':
+ *  - we set it to MODESET_ON_LID_OPEN on lid close,
+ *    and set it to MODESET_DONE on open
  *  - we use it as a "only once" bit (ie we ignore
- *    duplicate events where it was already properly
- *    set/reset)
- *  - the suspend/resume paths will also set it to
- *    zero, since they restore the mode ("lid open").
+ *    duplicate events where it was already properly set)
+ *  - the suspend/resume paths will set it to
+ *    MODESET_SUSPENDED and ignore the lid open event,
+ *    because they restore the mode ("lid open").
  */
 static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 			    void *unused)
@@ -512,6 +513,9 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 	if (dev->switch_power_state != DRM_SWITCH_POWER_ON)
 		return NOTIFY_OK;
 
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	if (dev_priv->modeset_restore == MODESET_SUSPENDED)
+		goto exit;
 	/*
 	 * check and update the status of LVDS connector after receiving
 	 * the LID nofication event.
@@ -520,21 +524,24 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 
 	/* Don't force modeset on machines where it causes a GPU lockup */
 	if (dmi_check_system(intel_no_modeset_on_lid))
-		return NOTIFY_OK;
+		goto exit;
 	if (!acpi_lid_open()) {
-		dev_priv->modeset_on_lid = 1;
-		return NOTIFY_OK;
+		/* do modeset on next lid open event */
+		dev_priv->modeset_restore = MODESET_ON_LID_OPEN;
+		goto exit;
 	}
 
-	if (!dev_priv->modeset_on_lid)
-		return NOTIFY_OK;
-
-	dev_priv->modeset_on_lid = 0;
+	if (dev_priv->modeset_restore == MODESET_DONE)
+		goto exit;
 
 	mutex_lock(&dev->mode_config.mutex);
 	intel_modeset_setup_hw_state(dev, true);
 	mutex_unlock(&dev->mode_config.mutex);
 
+	dev_priv->modeset_restore = MODESET_DONE;
+
+exit:
+	mutex_unlock(&dev_priv->modeset_restore_lock);
 	return NOTIFY_OK;
 }
 
Signature · 1 line
1.7.9.5
#6 lore raw

Re: [Intel-gfx] [PATCH V2 3/3] i915: ignore lid open event when resuming

Quoted 11 lines · Zhang Rui

oops, forgot to update the changelog and comments. refreshed patch attached.

From b584fcebb6d715a317f192c88606b875ee88ce78 Mon Sep 17 00:00:00 2001
From: Zhang Rui <[email protected]>
Date: Thu, 24 Jan 2013 13:27:22 +0800
Subject: [PATCH V3 3/3] i915: ignore lid open event when resuming

i915 driver needs to do modeset when
1. system resumes from sleep
2. lid is opened

Patch applied, thanks. There's been a bit of a merge conflict and one tiny checkpatch error, both fixed while applying. I plan to push this patch to drm-next for 3.9.
-Daniel

Quoted 232 lines

In PM_SUSPEND_MEM state, all the GPEs are cleared when system resumes, thus it is the i915_resume code does the modeset rather than intel_lid_notify().

But in PM_SUSPEND_FREEZE state, this will be broken because
system is still responsive to the lid events.
1. When we close the lid in Freeze state, intel_lid_notify() sets modeset_on_lid.
2. When we reopen the lid, intel_lid_notify() will do a modeset, before the system is resumed.
here is the error log,

[92146.548074] WARNING: at drivers/gpu/drm/i915/intel_display.c:1028 intel_wait_for_pipe_off+0x184/0x190 [i915]()
[92146.548076] Hardware name: VGN-Z540N
[92146.548078] pipe_off wait timed out
[92146.548167] Modules linked in: hid_generic usbhid hid snd_hda_codec_realtek snd_hda_intel snd_hda_codec parport_pc snd_hwdep ppdev snd_pcm_oss i915 snd_mixer_oss snd_pcm arc4 iwldvm snd_seq_dummy mac80211 snd_seq_oss snd_seq_midi fbcon tileblit font bitblit softcursor drm_kms_helper snd_rawmidi snd_seq_midi_event coretemp drm snd_seq kvm btusb bluetooth snd_timer iwlwifi pcmcia tpm_infineon i2c_algo_bit joydev snd_seq_device intel_agp cfg80211 snd intel_gtt yenta_socket pcmcia_rsrc sony_laptop agpgart microcode psmouse tpm_tis serio_raw mxm_wmi soundcore snd_page_alloc tpm acpi_cpufreq lpc_ich pcmcia_core tpm_bios mperf processor lp parport firewire_ohci firewire_core crc_itu_t sdhci_pci sdhci thermal e1000e
[92146.548173] Pid: 4304, comm: kworker/0:0 Tainted: G        W    3.8.0-rc3-s0i3-v3-test+ #9
[92146.548175] Call Trace:
[92146.548189]  [<c10378e2>] warn_slowpath_common+0x72/0xa0
[92146.548227]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548263]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548270]  [<c10379b3>] warn_slowpath_fmt+0x33/0x40
[92146.548307]  [<f86398b4>] intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548344]  [<f86399c2>] intel_disable_pipe+0x102/0x190 [i915]
[92146.548380]  [<f8639ea4>] ? intel_disable_plane+0x64/0x80 [i915]
[92146.548417]  [<f8639f7c>] i9xx_crtc_disable+0xbc/0x150 [i915]
[92146.548456]  [<f863ebee>] intel_crtc_update_dpms+0x5e/0x90 [i915]
[92146.548493]  [<f86437cf>] intel_modeset_setup_hw_state+0x42f/0x8f0 [i915]
[92146.548535]  [<f8645b0b>] intel_lid_notify+0x9b/0xc0 [i915]
[92146.548543]  [<c15610d3>] notifier_call_chain+0x43/0x60
[92146.548550]  [<c105d1e1>] __blocking_notifier_call_chain+0x41/0x80
[92146.548556]  [<c105d23f>] blocking_notifier_call_chain+0x1f/0x30
[92146.548563]  [<c131a684>] acpi_lid_send_state+0x78/0xa4
[92146.548569]  [<c131aa9e>] acpi_button_notify+0x3b/0xf1
[92146.548577]  [<c12df56a>] ? acpi_os_execute+0x17/0x19
[92146.548582]  [<c12e591a>] ? acpi_ec_sync_query+0xa5/0xbc
[92146.548589]  [<c12e2b82>] acpi_device_notify+0x16/0x18
[92146.548595]  [<c12f4904>] acpi_ev_notify_dispatch+0x38/0x4f
[92146.548600]  [<c12df0e8>] acpi_os_execute_deferred+0x20/0x2b
[92146.548607]  [<c1051208>] process_one_work+0x128/0x3f0
[92146.548613]  [<c1564f73>] ? common_interrupt+0x33/0x38
[92146.548618]  [<c104f8c0>] ? wake_up_worker+0x30/0x30
[92146.548624]  [<c12df0c8>] ? acpi_os_wait_events_complete+0x1e/0x1e
[92146.548629]  [<c10524f9>] worker_thread+0x119/0x3b0
[92146.548634]  [<c10523e0>] ? manage_workers+0x240/0x240
[92146.548640]  [<c1056e84>] kthread+0x94/0xa0
[92146.548647]  [<c1060000>] ? ftrace_raw_output_sched_stat_runtime+0x70/0xf0
[92146.548652]  [<c15649b7>] ret_from_kernel_thread+0x1b/0x28
[92146.548658]  [<c1056df0>] ? kthread_create_on_node+0xc0/0xc0

three different modeset flags are introduced in this patch

MODESET_ON_LID_OPEN: do modeset on next lid open event
MODESET_DONE:  modeset already done
MODESET_SUSPENDED:  suspended, only do modeset when system is resumed

In this way,
1. when lid is closed, MODESET_ON_LID_OPEN is set so that we'll do modeset on next lid open event.
2. when lid is opened, MODESET_DONE is set
so that duplicate lid open events will be ignored.
3. when system suspends, MODESET_SUSPENDED is set. In this case, we will not do modeset on any lid events.

Plus, locking mechanism is also introduced to avoid racing.

---
 drivers/gpu/drm/i915/i915_dma.c   |    1 +
 drivers/gpu/drm/i915/i915_drv.c   |   14 +++++++++-----
 drivers/gpu/drm/i915/i915_drv.h   |   11 +++++++++--
 drivers/gpu/drm/i915/intel_lvds.c |   33 ++++++++++++++++++++-------------
 4 files changed, 39 insertions(+), 20 deletions(-)
drivers/gpu/drm/i915/i915_dma.c +1 -0
index 99daa89..a5115d8 100644
@@ -1585,6 +1585,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	spin_lock_init(&dev_priv->dpio_lock);
 
 	mutex_init(&dev_priv->rps.hw_lock);
+	mutex_init(&dev_priv->modeset_restore_lock);
 
 	if (IS_IVYBRIDGE(dev) || IS_HASWELL(dev))
 		dev_priv->num_pipe = 3;
drivers/gpu/drm/i915/i915_drv.c +9 -5
index 1172658..68c6048 100644
@@ -468,6 +468,12 @@ static int i915_drm_freeze(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 
+	/* ignore lid events during suspend */
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	dev_priv->modeset_restore = MODESET_SUSPENDED;
+	mutex_unlock(&dev_priv->modeset_restore_lock);
+
+
 	drm_kms_helper_poll_disable(dev);
 
 	pci_save_state(dev->pdev);
@@ -492,9 +498,6 @@ static int i915_drm_freeze(struct drm_device *dev)
 
 	intel_opregion_fini(dev);
 
-	/* Modeset on resume, not lid events */
-	dev_priv->modeset_on_lid = 0;
-
 	console_lock();
 	intel_fbdev_set_suspend(dev, 1);
 	console_unlock();
@@ -569,8 +572,6 @@ static int __i915_drm_thaw(struct drm_device *dev)
 
 	intel_opregion_init(dev);
 
-	dev_priv->modeset_on_lid = 0;
-
 	/*
 	 * The console lock can be pretty contented on resume due
 	 * to all the printk activity.  Try to keep it out of the hot
@@ -583,6 +584,9 @@ static int __i915_drm_thaw(struct drm_device *dev)
 		schedule_work(&dev_priv->console_resume_work);
 	}
 
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	dev_priv->modeset_restore = MODESET_DONE;
+	mutex_unlock(&dev_priv->modeset_restore_lock);
 	return error;
 }
 
drivers/gpu/drm/i915/i915_drv.h +9 -2
index 12ab3bd..0fddad01 100644
@@ -620,6 +620,12 @@ struct intel_l3_parity {
 	struct work_struct error_work;
 };
 
+enum modeset_restore {
+	MODESET_ON_LID_OPEN,
+	MODESET_DONE,
+	MODESET_SUSPENDED,
+};
+
 typedef struct drm_i915_private {
 	struct drm_device *dev;
 
@@ -750,9 +756,10 @@ typedef struct drm_i915_private {
 
 	unsigned long quirks;
 
-	/* Register state */
-	bool modeset_on_lid;
+	enum modeset_restore modeset_restore; 
+	struct mutex modeset_restore_lock;
 
+	/* Register state */
 	struct {
 		/** Bridge to intel-gtt-ko */
 		struct intel_gtt *gtt;
drivers/gpu/drm/i915/intel_lvds.c +20 -13
index 17aee74..ff89d58 100644
@@ -492,13 +492,14 @@ static const struct dmi_system_id intel_no_modeset_on_lid[] = {
 };
 
 /*
- * Lid events. Note the use of 'modeset_on_lid':
- *  - we set it on lid close, and reset it on open
+ * Lid events. Note the use of 'modeset':
+ *  - we set it to MODESET_ON_LID_OPEN on lid close,
+ *    and set it to MODESET_DONE on open
  *  - we use it as a "only once" bit (ie we ignore
- *    duplicate events where it was already properly
- *    set/reset)
- *  - the suspend/resume paths will also set it to
- *    zero, since they restore the mode ("lid open").
+ *    duplicate events where it was already properly set)
+ *  - the suspend/resume paths will set it to
+ *    MODESET_SUSPENDED and ignore the lid open event,
+ *    because they restore the mode ("lid open").
  */
 static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 			    void *unused)
@@ -512,6 +513,9 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 	if (dev->switch_power_state != DRM_SWITCH_POWER_ON)
 		return NOTIFY_OK;
 
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	if (dev_priv->modeset_restore == MODESET_SUSPENDED)
+		goto exit;
 	/*
 	 * check and update the status of LVDS connector after receiving
 	 * the LID nofication event.
@@ -520,21 +524,24 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 
 	/* Don't force modeset on machines where it causes a GPU lockup */
 	if (dmi_check_system(intel_no_modeset_on_lid))
-		return NOTIFY_OK;
+		goto exit;
 	if (!acpi_lid_open()) {
-		dev_priv->modeset_on_lid = 1;
-		return NOTIFY_OK;
+		/* do modeset on next lid open event */
+		dev_priv->modeset_restore = MODESET_ON_LID_OPEN;
+		goto exit;
 	}
 
-	if (!dev_priv->modeset_on_lid)
-		return NOTIFY_OK;
-
-	dev_priv->modeset_on_lid = 0;
+	if (dev_priv->modeset_restore == MODESET_DONE)
+		goto exit;
 
 	mutex_lock(&dev->mode_config.mutex);
 	intel_modeset_setup_hw_state(dev, true);
 	mutex_unlock(&dev->mode_config.mutex);
 
+	dev_priv->modeset_restore = MODESET_DONE;
+
+exit:
+	mutex_unlock(&dev_priv->modeset_restore_lock);
 	return NOTIFY_OK;
 }
 
Signature · 1 line
1.7.9.5
Signature · 3 lines
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch
#7 lore raw

Re: [Intel-gfx] [PATCH V2 3/3] i915: ignore lid open event when resuming

Quoted 9 lines · Daniel Vetter
Quoted 8 lines · Zhang Rui

oops, forgot to update the changelog and comments. refreshed patch attached.

From b584fcebb6d715a317f192c88606b875ee88ce78 Mon Sep 17 00:00:00 2001
From: Zhang Rui <[email protected]>
Date: Thu, 24 Jan 2013 13:27:22 +0800
Subject: [PATCH V3 3/3] i915: ignore lid open event when resuming

Quoted 7 lines
Quoted 3 lines

i915 driver needs to do modeset when
1. system resumes from sleep
2. lid is opened

Patch applied, thanks. There's been a bit of a merge conflict and one tiny checkpatch error, both fixed while applying. I plan to push this patch to drm-next for 3.9.

Thanks Daniel!

I will take the other patches from the series, then.

Rafael

Quoted 228 lines
Quoted 226 lines

In PM_SUSPEND_MEM state, all the GPEs are cleared when system resumes, thus it is the i915_resume code does the modeset rather than intel_lid_notify().

But in PM_SUSPEND_FREEZE state, this will be broken because
system is still responsive to the lid events.
1. When we close the lid in Freeze state, intel_lid_notify() sets modeset_on_lid.
2. When we reopen the lid, intel_lid_notify() will do a modeset, before the system is resumed.
here is the error log,

[92146.548074] WARNING: at drivers/gpu/drm/i915/intel_display.c:1028 intel_wait_for_pipe_off+0x184/0x190 [i915]()
[92146.548076] Hardware name: VGN-Z540N
[92146.548078] pipe_off wait timed out
[92146.548167] Modules linked in: hid_generic usbhid hid snd_hda_codec_realtek snd_hda_intel snd_hda_codec parport_pc snd_hwdep ppdev snd_pcm_oss i915 snd_mixer_oss snd_pcm arc4 iwldvm snd_seq_dummy mac80211 snd_seq_oss snd_seq_midi fbcon tileblit font bitblit softcursor drm_kms_helper snd_rawmidi snd_seq_midi_event coretemp drm snd_seq kvm btusb bluetooth snd_timer iwlwifi pcmcia tpm_infineon i2c_algo_bit joydev snd_seq_device intel_agp cfg80211 snd intel_gtt yenta_socket pcmcia_rsrc sony_laptop agpgart microcode psmouse tpm_tis serio_raw mxm_wmi soundcore snd_page_alloc tpm acpi_cpufreq lpc_ich pcmcia_core tpm_bios mperf processor lp parport firewire_ohci firewire_core crc_itu_t sdhci_pci sdhci thermal e1000e
[92146.548173] Pid: 4304, comm: kworker/0:0 Tainted: G        W    3.8.0-rc3-s0i3-v3-test+ #9
[92146.548175] Call Trace:
[92146.548189]  [<c10378e2>] warn_slowpath_common+0x72/0xa0
[92146.548227]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548263]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548270]  [<c10379b3>] warn_slowpath_fmt+0x33/0x40
[92146.548307]  [<f86398b4>] intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548344]  [<f86399c2>] intel_disable_pipe+0x102/0x190 [i915]
[92146.548380]  [<f8639ea4>] ? intel_disable_plane+0x64/0x80 [i915]
[92146.548417]  [<f8639f7c>] i9xx_crtc_disable+0xbc/0x150 [i915]
[92146.548456]  [<f863ebee>] intel_crtc_update_dpms+0x5e/0x90 [i915]
[92146.548493]  [<f86437cf>] intel_modeset_setup_hw_state+0x42f/0x8f0 [i915]
[92146.548535]  [<f8645b0b>] intel_lid_notify+0x9b/0xc0 [i915]
[92146.548543]  [<c15610d3>] notifier_call_chain+0x43/0x60
[92146.548550]  [<c105d1e1>] __blocking_notifier_call_chain+0x41/0x80
[92146.548556]  [<c105d23f>] blocking_notifier_call_chain+0x1f/0x30
[92146.548563]  [<c131a684>] acpi_lid_send_state+0x78/0xa4
[92146.548569]  [<c131aa9e>] acpi_button_notify+0x3b/0xf1
[92146.548577]  [<c12df56a>] ? acpi_os_execute+0x17/0x19
[92146.548582]  [<c12e591a>] ? acpi_ec_sync_query+0xa5/0xbc
[92146.548589]  [<c12e2b82>] acpi_device_notify+0x16/0x18
[92146.548595]  [<c12f4904>] acpi_ev_notify_dispatch+0x38/0x4f
[92146.548600]  [<c12df0e8>] acpi_os_execute_deferred+0x20/0x2b
[92146.548607]  [<c1051208>] process_one_work+0x128/0x3f0
[92146.548613]  [<c1564f73>] ? common_interrupt+0x33/0x38
[92146.548618]  [<c104f8c0>] ? wake_up_worker+0x30/0x30
[92146.548624]  [<c12df0c8>] ? acpi_os_wait_events_complete+0x1e/0x1e
[92146.548629]  [<c10524f9>] worker_thread+0x119/0x3b0
[92146.548634]  [<c10523e0>] ? manage_workers+0x240/0x240
[92146.548640]  [<c1056e84>] kthread+0x94/0xa0
[92146.548647]  [<c1060000>] ? ftrace_raw_output_sched_stat_runtime+0x70/0xf0
[92146.548652]  [<c15649b7>] ret_from_kernel_thread+0x1b/0x28
[92146.548658]  [<c1056df0>] ? kthread_create_on_node+0xc0/0xc0

three different modeset flags are introduced in this patch

MODESET_ON_LID_OPEN: do modeset on next lid open event
MODESET_DONE:  modeset already done
MODESET_SUSPENDED:  suspended, only do modeset when system is resumed

In this way,
1. when lid is closed, MODESET_ON_LID_OPEN is set so that we'll do modeset on next lid open event.
2. when lid is opened, MODESET_DONE is set
so that duplicate lid open events will be ignored.
3. when system suspends, MODESET_SUSPENDED is set. In this case, we will not do modeset on any lid events.

Plus, locking mechanism is also introduced to avoid racing.

---
 drivers/gpu/drm/i915/i915_dma.c   |    1 +
 drivers/gpu/drm/i915/i915_drv.c   |   14 +++++++++-----
 drivers/gpu/drm/i915/i915_drv.h   |   11 +++++++++--
 drivers/gpu/drm/i915/intel_lvds.c |   33 ++++++++++++++++++++-------------
 4 files changed, 39 insertions(+), 20 deletions(-)
drivers/gpu/drm/i915/i915_dma.c +1 -0
index 99daa89..a5115d8 100644
@@ -1585,6 +1585,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	spin_lock_init(&dev_priv->dpio_lock);
 
 	mutex_init(&dev_priv->rps.hw_lock);
+	mutex_init(&dev_priv->modeset_restore_lock);
 
 	if (IS_IVYBRIDGE(dev) || IS_HASWELL(dev))
 		dev_priv->num_pipe = 3;
drivers/gpu/drm/i915/i915_drv.c +9 -5
index 1172658..68c6048 100644
@@ -468,6 +468,12 @@ static int i915_drm_freeze(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 
+	/* ignore lid events during suspend */
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	dev_priv->modeset_restore = MODESET_SUSPENDED;
+	mutex_unlock(&dev_priv->modeset_restore_lock);
+
+
 	drm_kms_helper_poll_disable(dev);
 
 	pci_save_state(dev->pdev);
@@ -492,9 +498,6 @@ static int i915_drm_freeze(struct drm_device *dev)
 
 	intel_opregion_fini(dev);
 
-	/* Modeset on resume, not lid events */
-	dev_priv->modeset_on_lid = 0;
-
 	console_lock();
 	intel_fbdev_set_suspend(dev, 1);
 	console_unlock();
@@ -569,8 +572,6 @@ static int __i915_drm_thaw(struct drm_device *dev)
 
 	intel_opregion_init(dev);
 
-	dev_priv->modeset_on_lid = 0;
-
 	/*
 	 * The console lock can be pretty contented on resume due
 	 * to all the printk activity.  Try to keep it out of the hot
@@ -583,6 +584,9 @@ static int __i915_drm_thaw(struct drm_device *dev)
 		schedule_work(&dev_priv->console_resume_work);
 	}
 
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	dev_priv->modeset_restore = MODESET_DONE;
+	mutex_unlock(&dev_priv->modeset_restore_lock);
 	return error;
 }
 
drivers/gpu/drm/i915/i915_drv.h +9 -2
index 12ab3bd..0fddad01 100644
@@ -620,6 +620,12 @@ struct intel_l3_parity {
 	struct work_struct error_work;
 };
 
+enum modeset_restore {
+	MODESET_ON_LID_OPEN,
+	MODESET_DONE,
+	MODESET_SUSPENDED,
+};
+
 typedef struct drm_i915_private {
 	struct drm_device *dev;
 
@@ -750,9 +756,10 @@ typedef struct drm_i915_private {
 
 	unsigned long quirks;
 
-	/* Register state */
-	bool modeset_on_lid;
+	enum modeset_restore modeset_restore; 
+	struct mutex modeset_restore_lock;
 
+	/* Register state */
 	struct {
 		/** Bridge to intel-gtt-ko */
 		struct intel_gtt *gtt;
drivers/gpu/drm/i915/intel_lvds.c +20 -13
index 17aee74..ff89d58 100644
@@ -492,13 +492,14 @@ static const struct dmi_system_id intel_no_modeset_on_lid[] = {
 };
 
 /*
- * Lid events. Note the use of 'modeset_on_lid':
- *  - we set it on lid close, and reset it on open
+ * Lid events. Note the use of 'modeset':
+ *  - we set it to MODESET_ON_LID_OPEN on lid close,
+ *    and set it to MODESET_DONE on open
  *  - we use it as a "only once" bit (ie we ignore
- *    duplicate events where it was already properly
- *    set/reset)
- *  - the suspend/resume paths will also set it to
- *    zero, since they restore the mode ("lid open").
+ *    duplicate events where it was already properly set)
+ *  - the suspend/resume paths will set it to
+ *    MODESET_SUSPENDED and ignore the lid open event,
+ *    because they restore the mode ("lid open").
  */
 static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 			    void *unused)
@@ -512,6 +513,9 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 	if (dev->switch_power_state != DRM_SWITCH_POWER_ON)
 		return NOTIFY_OK;
 
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	if (dev_priv->modeset_restore == MODESET_SUSPENDED)
+		goto exit;
 	/*
 	 * check and update the status of LVDS connector after receiving
 	 * the LID nofication event.
@@ -520,21 +524,24 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 
 	/* Don't force modeset on machines where it causes a GPU lockup */
 	if (dmi_check_system(intel_no_modeset_on_lid))
-		return NOTIFY_OK;
+		goto exit;
 	if (!acpi_lid_open()) {
-		dev_priv->modeset_on_lid = 1;
-		return NOTIFY_OK;
+		/* do modeset on next lid open event */
+		dev_priv->modeset_restore = MODESET_ON_LID_OPEN;
+		goto exit;
 	}
 
-	if (!dev_priv->modeset_on_lid)
-		return NOTIFY_OK;
-
-	dev_priv->modeset_on_lid = 0;
+	if (dev_priv->modeset_restore == MODESET_DONE)
+		goto exit;
 
 	mutex_lock(&dev->mode_config.mutex);
 	intel_modeset_setup_hw_state(dev, true);
 	mutex_unlock(&dev->mode_config.mutex);
 
+	dev_priv->modeset_restore = MODESET_DONE;
+
+exit:
+	mutex_unlock(&dev_priv->modeset_restore_lock);
 	return NOTIFY_OK;
 }
 
Signature · 2 lines
I speak only for myself.
Rafael J. Wysocki, Intel Open Source Technology Center.
author
#8 lore raw

Re: [Intel-gfx] [PATCH V2 3/3] i915: ignore lid open event when resuming

Quoted 14 lines · Rafael J. Wysocki
Quoted 13 lines · Daniel Vetter
Quoted 11 lines · Zhang Rui

oops, forgot to update the changelog and comments. refreshed patch attached.

From b584fcebb6d715a317f192c88606b875ee88ce78 Mon Sep 17 00:00:00 2001
From: Zhang Rui <[email protected]>
Date: Thu, 24 Jan 2013 13:27:22 +0800
Subject: [PATCH V3 3/3] i915: ignore lid open event when resuming

i915 driver needs to do modeset when
1. system resumes from sleep
2. lid is opened

Quoted 8 lines
Quoted 3 lines

Patch applied, thanks. There's been a bit of a merge conflict and one tiny checkpatch error, both fixed while applying. I plan to push this patch to drm-next for 3.9.

Thanks Daniel!

I will take the other patches from the series, then.

great, thank you, Rafael.

-rui

Quoted 231 lines

Rafael

Quoted 228 lines
Quoted 226 lines

In PM_SUSPEND_MEM state, all the GPEs are cleared when system resumes, thus it is the i915_resume code does the modeset rather than intel_lid_notify().

But in PM_SUSPEND_FREEZE state, this will be broken because
system is still responsive to the lid events.
1. When we close the lid in Freeze state, intel_lid_notify() sets modeset_on_lid.
2. When we reopen the lid, intel_lid_notify() will do a modeset, before the system is resumed.
here is the error log,

[92146.548074] WARNING: at drivers/gpu/drm/i915/intel_display.c:1028 intel_wait_for_pipe_off+0x184/0x190 [i915]()
[92146.548076] Hardware name: VGN-Z540N
[92146.548078] pipe_off wait timed out
[92146.548167] Modules linked in: hid_generic usbhid hid snd_hda_codec_realtek snd_hda_intel snd_hda_codec parport_pc snd_hwdep ppdev snd_pcm_oss i915 snd_mixer_oss snd_pcm arc4 iwldvm snd_seq_dummy mac80211 snd_seq_oss snd_seq_midi fbcon tileblit font bitblit softcursor drm_kms_helper snd_rawmidi snd_seq_midi_event coretemp drm snd_seq kvm btusb bluetooth snd_timer iwlwifi pcmcia tpm_infineon i2c_algo_bit joydev snd_seq_device intel_agp cfg80211 snd intel_gtt yenta_socket pcmcia_rsrc sony_laptop agpgart microcode psmouse tpm_tis serio_raw mxm_wmi soundcore snd_page_alloc tpm acpi_cpufreq lpc_ich pcmcia_core tpm_bios mperf processor lp parport firewire_ohci firewire_core crc_itu_t sdhci_pci sdhci thermal e1000e
[92146.548173] Pid: 4304, comm: kworker/0:0 Tainted: G        W    3.8.0-rc3-s0i3-v3-test+ #9
[92146.548175] Call Trace:
[92146.548189]  [<c10378e2>] warn_slowpath_common+0x72/0xa0
[92146.548227]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548263]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548270]  [<c10379b3>] warn_slowpath_fmt+0x33/0x40
[92146.548307]  [<f86398b4>] intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548344]  [<f86399c2>] intel_disable_pipe+0x102/0x190 [i915]
[92146.548380]  [<f8639ea4>] ? intel_disable_plane+0x64/0x80 [i915]
[92146.548417]  [<f8639f7c>] i9xx_crtc_disable+0xbc/0x150 [i915]
[92146.548456]  [<f863ebee>] intel_crtc_update_dpms+0x5e/0x90 [i915]
[92146.548493]  [<f86437cf>] intel_modeset_setup_hw_state+0x42f/0x8f0 [i915]
[92146.548535]  [<f8645b0b>] intel_lid_notify+0x9b/0xc0 [i915]
[92146.548543]  [<c15610d3>] notifier_call_chain+0x43/0x60
[92146.548550]  [<c105d1e1>] __blocking_notifier_call_chain+0x41/0x80
[92146.548556]  [<c105d23f>] blocking_notifier_call_chain+0x1f/0x30
[92146.548563]  [<c131a684>] acpi_lid_send_state+0x78/0xa4
[92146.548569]  [<c131aa9e>] acpi_button_notify+0x3b/0xf1
[92146.548577]  [<c12df56a>] ? acpi_os_execute+0x17/0x19
[92146.548582]  [<c12e591a>] ? acpi_ec_sync_query+0xa5/0xbc
[92146.548589]  [<c12e2b82>] acpi_device_notify+0x16/0x18
[92146.548595]  [<c12f4904>] acpi_ev_notify_dispatch+0x38/0x4f
[92146.548600]  [<c12df0e8>] acpi_os_execute_deferred+0x20/0x2b
[92146.548607]  [<c1051208>] process_one_work+0x128/0x3f0
[92146.548613]  [<c1564f73>] ? common_interrupt+0x33/0x38
[92146.548618]  [<c104f8c0>] ? wake_up_worker+0x30/0x30
[92146.548624]  [<c12df0c8>] ? acpi_os_wait_events_complete+0x1e/0x1e
[92146.548629]  [<c10524f9>] worker_thread+0x119/0x3b0
[92146.548634]  [<c10523e0>] ? manage_workers+0x240/0x240
[92146.548640]  [<c1056e84>] kthread+0x94/0xa0
[92146.548647]  [<c1060000>] ? ftrace_raw_output_sched_stat_runtime+0x70/0xf0
[92146.548652]  [<c15649b7>] ret_from_kernel_thread+0x1b/0x28
[92146.548658]  [<c1056df0>] ? kthread_create_on_node+0xc0/0xc0

three different modeset flags are introduced in this patch

MODESET_ON_LID_OPEN: do modeset on next lid open event
MODESET_DONE:  modeset already done
MODESET_SUSPENDED:  suspended, only do modeset when system is resumed

In this way,
1. when lid is closed, MODESET_ON_LID_OPEN is set so that we'll do modeset on next lid open event.
2. when lid is opened, MODESET_DONE is set
so that duplicate lid open events will be ignored.
3. when system suspends, MODESET_SUSPENDED is set. In this case, we will not do modeset on any lid events.

Plus, locking mechanism is also introduced to avoid racing.

---
 drivers/gpu/drm/i915/i915_dma.c   |    1 +
 drivers/gpu/drm/i915/i915_drv.c   |   14 +++++++++-----
 drivers/gpu/drm/i915/i915_drv.h   |   11 +++++++++--
 drivers/gpu/drm/i915/intel_lvds.c |   33 ++++++++++++++++++++-------------
 4 files changed, 39 insertions(+), 20 deletions(-)
drivers/gpu/drm/i915/i915_dma.c +1 -0
index 99daa89..a5115d8 100644
@@ -1585,6 +1585,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	spin_lock_init(&dev_priv->dpio_lock);
 
 	mutex_init(&dev_priv->rps.hw_lock);
+	mutex_init(&dev_priv->modeset_restore_lock);
 
 	if (IS_IVYBRIDGE(dev) || IS_HASWELL(dev))
 		dev_priv->num_pipe = 3;
drivers/gpu/drm/i915/i915_drv.c +9 -5
index 1172658..68c6048 100644
@@ -468,6 +468,12 @@ static int i915_drm_freeze(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 
+	/* ignore lid events during suspend */
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	dev_priv->modeset_restore = MODESET_SUSPENDED;
+	mutex_unlock(&dev_priv->modeset_restore_lock);
+
+
 	drm_kms_helper_poll_disable(dev);
 
 	pci_save_state(dev->pdev);
@@ -492,9 +498,6 @@ static int i915_drm_freeze(struct drm_device *dev)
 
 	intel_opregion_fini(dev);
 
-	/* Modeset on resume, not lid events */
-	dev_priv->modeset_on_lid = 0;
-
 	console_lock();
 	intel_fbdev_set_suspend(dev, 1);
 	console_unlock();
@@ -569,8 +572,6 @@ static int __i915_drm_thaw(struct drm_device *dev)
 
 	intel_opregion_init(dev);
 
-	dev_priv->modeset_on_lid = 0;
-
 	/*
 	 * The console lock can be pretty contented on resume due
 	 * to all the printk activity.  Try to keep it out of the hot
@@ -583,6 +584,9 @@ static int __i915_drm_thaw(struct drm_device *dev)
 		schedule_work(&dev_priv->console_resume_work);
 	}
 
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	dev_priv->modeset_restore = MODESET_DONE;
+	mutex_unlock(&dev_priv->modeset_restore_lock);
 	return error;
 }
 
drivers/gpu/drm/i915/i915_drv.h +9 -2
index 12ab3bd..0fddad01 100644
@@ -620,6 +620,12 @@ struct intel_l3_parity {
 	struct work_struct error_work;
 };
 
+enum modeset_restore {
+	MODESET_ON_LID_OPEN,
+	MODESET_DONE,
+	MODESET_SUSPENDED,
+};
+
 typedef struct drm_i915_private {
 	struct drm_device *dev;
 
@@ -750,9 +756,10 @@ typedef struct drm_i915_private {
 
 	unsigned long quirks;
 
-	/* Register state */
-	bool modeset_on_lid;
+	enum modeset_restore modeset_restore; 
+	struct mutex modeset_restore_lock;
 
+	/* Register state */
 	struct {
 		/** Bridge to intel-gtt-ko */
 		struct intel_gtt *gtt;
drivers/gpu/drm/i915/intel_lvds.c +20 -13
index 17aee74..ff89d58 100644
@@ -492,13 +492,14 @@ static const struct dmi_system_id intel_no_modeset_on_lid[] = {
 };
 
 /*
- * Lid events. Note the use of 'modeset_on_lid':
- *  - we set it on lid close, and reset it on open
+ * Lid events. Note the use of 'modeset':
+ *  - we set it to MODESET_ON_LID_OPEN on lid close,
+ *    and set it to MODESET_DONE on open
  *  - we use it as a "only once" bit (ie we ignore
- *    duplicate events where it was already properly
- *    set/reset)
- *  - the suspend/resume paths will also set it to
- *    zero, since they restore the mode ("lid open").
+ *    duplicate events where it was already properly set)
+ *  - the suspend/resume paths will set it to
+ *    MODESET_SUSPENDED and ignore the lid open event,
+ *    because they restore the mode ("lid open").
  */
 static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 			    void *unused)
@@ -512,6 +513,9 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 	if (dev->switch_power_state != DRM_SWITCH_POWER_ON)
 		return NOTIFY_OK;
 
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	if (dev_priv->modeset_restore == MODESET_SUSPENDED)
+		goto exit;
 	/*
 	 * check and update the status of LVDS connector after receiving
 	 * the LID nofication event.
@@ -520,21 +524,24 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 
 	/* Don't force modeset on machines where it causes a GPU lockup */
 	if (dmi_check_system(intel_no_modeset_on_lid))
-		return NOTIFY_OK;
+		goto exit;
 	if (!acpi_lid_open()) {
-		dev_priv->modeset_on_lid = 1;
-		return NOTIFY_OK;
+		/* do modeset on next lid open event */
+		dev_priv->modeset_restore = MODESET_ON_LID_OPEN;
+		goto exit;
 	}
 
-	if (!dev_priv->modeset_on_lid)
-		return NOTIFY_OK;
-
-	dev_priv->modeset_on_lid = 0;
+	if (dev_priv->modeset_restore == MODESET_DONE)
+		goto exit;
 
 	mutex_lock(&dev->mode_config.mutex);
 	intel_modeset_setup_hw_state(dev, true);
 	mutex_unlock(&dev->mode_config.mutex);
 
+	dev_priv->modeset_restore = MODESET_DONE;
+
+exit:
+	mutex_unlock(&dev_priv->modeset_restore_lock);
 	return NOTIFY_OK;
 }
 
author
#9 lore raw

Re: [Intel-gfx] [PATCH V2 3/3] i915: ignore lid open event when resuming

In reply to Daniel Vetter
Quoted 9 lines · Daniel Vetter
Quoted 8 lines · Zhang Rui

oops, forgot to update the changelog and comments. refreshed patch attached.

From b584fcebb6d715a317f192c88606b875ee88ce78 Mon Sep 17 00:00:00 2001
From: Zhang Rui <[email protected]>
Date: Thu, 24 Jan 2013 13:27:22 +0800
Subject: [PATCH V3 3/3] i915: ignore lid open event when resuming

Quoted 9 lines
Quoted 3 lines

i915 driver needs to do modeset when
1. system resumes from sleep
2. lid is opened

Patch applied, thanks. There's been a bit of a merge conflict and one tiny checkpatch error, both fixed while applying. I plan to push this patch to drm-next for 3.9.
-Daniel

great, thanks!

-rui

Quoted 233 lines
Quoted 232 lines

In PM_SUSPEND_MEM state, all the GPEs are cleared when system resumes, thus it is the i915_resume code does the modeset rather than intel_lid_notify().

But in PM_SUSPEND_FREEZE state, this will be broken because
system is still responsive to the lid events.
1. When we close the lid in Freeze state, intel_lid_notify() sets modeset_on_lid.
2. When we reopen the lid, intel_lid_notify() will do a modeset, before the system is resumed.
here is the error log,

[92146.548074] WARNING: at drivers/gpu/drm/i915/intel_display.c:1028 intel_wait_for_pipe_off+0x184/0x190 [i915]()
[92146.548076] Hardware name: VGN-Z540N
[92146.548078] pipe_off wait timed out
[92146.548167] Modules linked in: hid_generic usbhid hid snd_hda_codec_realtek snd_hda_intel snd_hda_codec parport_pc snd_hwdep ppdev snd_pcm_oss i915 snd_mixer_oss snd_pcm arc4 iwldvm snd_seq_dummy mac80211 snd_seq_oss snd_seq_midi fbcon tileblit font bitblit softcursor drm_kms_helper snd_rawmidi snd_seq_midi_event coretemp drm snd_seq kvm btusb bluetooth snd_timer iwlwifi pcmcia tpm_infineon i2c_algo_bit joydev snd_seq_device intel_agp cfg80211 snd intel_gtt yenta_socket pcmcia_rsrc sony_laptop agpgart microcode psmouse tpm_tis serio_raw mxm_wmi soundcore snd_page_alloc tpm acpi_cpufreq lpc_ich pcmcia_core tpm_bios mperf processor lp parport firewire_ohci firewire_core crc_itu_t sdhci_pci sdhci thermal e1000e
[92146.548173] Pid: 4304, comm: kworker/0:0 Tainted: G        W    3.8.0-rc3-s0i3-v3-test+ #9
[92146.548175] Call Trace:
[92146.548189]  [<c10378e2>] warn_slowpath_common+0x72/0xa0
[92146.548227]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548263]  [<f86398b4>] ? intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548270]  [<c10379b3>] warn_slowpath_fmt+0x33/0x40
[92146.548307]  [<f86398b4>] intel_wait_for_pipe_off+0x184/0x190 [i915]
[92146.548344]  [<f86399c2>] intel_disable_pipe+0x102/0x190 [i915]
[92146.548380]  [<f8639ea4>] ? intel_disable_plane+0x64/0x80 [i915]
[92146.548417]  [<f8639f7c>] i9xx_crtc_disable+0xbc/0x150 [i915]
[92146.548456]  [<f863ebee>] intel_crtc_update_dpms+0x5e/0x90 [i915]
[92146.548493]  [<f86437cf>] intel_modeset_setup_hw_state+0x42f/0x8f0 [i915]
[92146.548535]  [<f8645b0b>] intel_lid_notify+0x9b/0xc0 [i915]
[92146.548543]  [<c15610d3>] notifier_call_chain+0x43/0x60
[92146.548550]  [<c105d1e1>] __blocking_notifier_call_chain+0x41/0x80
[92146.548556]  [<c105d23f>] blocking_notifier_call_chain+0x1f/0x30
[92146.548563]  [<c131a684>] acpi_lid_send_state+0x78/0xa4
[92146.548569]  [<c131aa9e>] acpi_button_notify+0x3b/0xf1
[92146.548577]  [<c12df56a>] ? acpi_os_execute+0x17/0x19
[92146.548582]  [<c12e591a>] ? acpi_ec_sync_query+0xa5/0xbc
[92146.548589]  [<c12e2b82>] acpi_device_notify+0x16/0x18
[92146.548595]  [<c12f4904>] acpi_ev_notify_dispatch+0x38/0x4f
[92146.548600]  [<c12df0e8>] acpi_os_execute_deferred+0x20/0x2b
[92146.548607]  [<c1051208>] process_one_work+0x128/0x3f0
[92146.548613]  [<c1564f73>] ? common_interrupt+0x33/0x38
[92146.548618]  [<c104f8c0>] ? wake_up_worker+0x30/0x30
[92146.548624]  [<c12df0c8>] ? acpi_os_wait_events_complete+0x1e/0x1e
[92146.548629]  [<c10524f9>] worker_thread+0x119/0x3b0
[92146.548634]  [<c10523e0>] ? manage_workers+0x240/0x240
[92146.548640]  [<c1056e84>] kthread+0x94/0xa0
[92146.548647]  [<c1060000>] ? ftrace_raw_output_sched_stat_runtime+0x70/0xf0
[92146.548652]  [<c15649b7>] ret_from_kernel_thread+0x1b/0x28
[92146.548658]  [<c1056df0>] ? kthread_create_on_node+0xc0/0xc0

three different modeset flags are introduced in this patch

MODESET_ON_LID_OPEN: do modeset on next lid open event
MODESET_DONE:  modeset already done
MODESET_SUSPENDED:  suspended, only do modeset when system is resumed

In this way,
1. when lid is closed, MODESET_ON_LID_OPEN is set so that we'll do modeset on next lid open event.
2. when lid is opened, MODESET_DONE is set
so that duplicate lid open events will be ignored.
3. when system suspends, MODESET_SUSPENDED is set. In this case, we will not do modeset on any lid events.

Plus, locking mechanism is also introduced to avoid racing.

---
 drivers/gpu/drm/i915/i915_dma.c   |    1 +
 drivers/gpu/drm/i915/i915_drv.c   |   14 +++++++++-----
 drivers/gpu/drm/i915/i915_drv.h   |   11 +++++++++--
 drivers/gpu/drm/i915/intel_lvds.c |   33 ++++++++++++++++++++-------------
 4 files changed, 39 insertions(+), 20 deletions(-)
drivers/gpu/drm/i915/i915_dma.c +1 -0
index 99daa89..a5115d8 100644
@@ -1585,6 +1585,7 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
 	spin_lock_init(&dev_priv->dpio_lock);
 
 	mutex_init(&dev_priv->rps.hw_lock);
+	mutex_init(&dev_priv->modeset_restore_lock);
 
 	if (IS_IVYBRIDGE(dev) || IS_HASWELL(dev))
 		dev_priv->num_pipe = 3;
drivers/gpu/drm/i915/i915_drv.c +9 -5
index 1172658..68c6048 100644
@@ -468,6 +468,12 @@ static int i915_drm_freeze(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
 
+	/* ignore lid events during suspend */
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	dev_priv->modeset_restore = MODESET_SUSPENDED;
+	mutex_unlock(&dev_priv->modeset_restore_lock);
+
+
 	drm_kms_helper_poll_disable(dev);
 
 	pci_save_state(dev->pdev);
@@ -492,9 +498,6 @@ static int i915_drm_freeze(struct drm_device *dev)
 
 	intel_opregion_fini(dev);
 
-	/* Modeset on resume, not lid events */
-	dev_priv->modeset_on_lid = 0;
-
 	console_lock();
 	intel_fbdev_set_suspend(dev, 1);
 	console_unlock();
@@ -569,8 +572,6 @@ static int __i915_drm_thaw(struct drm_device *dev)
 
 	intel_opregion_init(dev);
 
-	dev_priv->modeset_on_lid = 0;
-
 	/*
 	 * The console lock can be pretty contented on resume due
 	 * to all the printk activity.  Try to keep it out of the hot
@@ -583,6 +584,9 @@ static int __i915_drm_thaw(struct drm_device *dev)
 		schedule_work(&dev_priv->console_resume_work);
 	}
 
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	dev_priv->modeset_restore = MODESET_DONE;
+	mutex_unlock(&dev_priv->modeset_restore_lock);
 	return error;
 }
 
drivers/gpu/drm/i915/i915_drv.h +9 -2
index 12ab3bd..0fddad01 100644
@@ -620,6 +620,12 @@ struct intel_l3_parity {
 	struct work_struct error_work;
 };
 
+enum modeset_restore {
+	MODESET_ON_LID_OPEN,
+	MODESET_DONE,
+	MODESET_SUSPENDED,
+};
+
 typedef struct drm_i915_private {
 	struct drm_device *dev;
 
@@ -750,9 +756,10 @@ typedef struct drm_i915_private {
 
 	unsigned long quirks;
 
-	/* Register state */
-	bool modeset_on_lid;
+	enum modeset_restore modeset_restore; 
+	struct mutex modeset_restore_lock;
 
+	/* Register state */
 	struct {
 		/** Bridge to intel-gtt-ko */
 		struct intel_gtt *gtt;
drivers/gpu/drm/i915/intel_lvds.c +20 -13
index 17aee74..ff89d58 100644
@@ -492,13 +492,14 @@ static const struct dmi_system_id intel_no_modeset_on_lid[] = {
 };
 
 /*
- * Lid events. Note the use of 'modeset_on_lid':
- *  - we set it on lid close, and reset it on open
+ * Lid events. Note the use of 'modeset':
+ *  - we set it to MODESET_ON_LID_OPEN on lid close,
+ *    and set it to MODESET_DONE on open
  *  - we use it as a "only once" bit (ie we ignore
- *    duplicate events where it was already properly
- *    set/reset)
- *  - the suspend/resume paths will also set it to
- *    zero, since they restore the mode ("lid open").
+ *    duplicate events where it was already properly set)
+ *  - the suspend/resume paths will set it to
+ *    MODESET_SUSPENDED and ignore the lid open event,
+ *    because they restore the mode ("lid open").
  */
 static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 			    void *unused)
@@ -512,6 +513,9 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 	if (dev->switch_power_state != DRM_SWITCH_POWER_ON)
 		return NOTIFY_OK;
 
+	mutex_lock(&dev_priv->modeset_restore_lock);
+	if (dev_priv->modeset_restore == MODESET_SUSPENDED)
+		goto exit;
 	/*
 	 * check and update the status of LVDS connector after receiving
 	 * the LID nofication event.
@@ -520,21 +524,24 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
 
 	/* Don't force modeset on machines where it causes a GPU lockup */
 	if (dmi_check_system(intel_no_modeset_on_lid))
-		return NOTIFY_OK;
+		goto exit;
 	if (!acpi_lid_open()) {
-		dev_priv->modeset_on_lid = 1;
-		return NOTIFY_OK;
+		/* do modeset on next lid open event */
+		dev_priv->modeset_restore = MODESET_ON_LID_OPEN;
+		goto exit;
 	}
 
-	if (!dev_priv->modeset_on_lid)
-		return NOTIFY_OK;
-
-	dev_priv->modeset_on_lid = 0;
+	if (dev_priv->modeset_restore == MODESET_DONE)
+		goto exit;
 
 	mutex_lock(&dev->mode_config.mutex);
 	intel_modeset_setup_hw_state(dev, true);
 	mutex_unlock(&dev->mode_config.mutex);
 
+	dev_priv->modeset_restore = MODESET_DONE;
+
+exit:
+	mutex_unlock(&dev_priv->modeset_restore_lock);
 	return NOTIFY_OK;
 }
 
Signature · 1 line
1.7.9.5
author
#10 lore raw
In reply to Zhang Rui
Quoted 74 lines · Zhang Rui

PM_SUSPEND_FREEZE state is a general state that does not need any platform specific support, it equals frozen processes + suspended devices + idle processors.

Compared with PM_SUSPEND_MEMORY,
PM_SUSPEND_FREEZE saves less power
because the system is still in a running state. PM_SUSPEND_FREEZE has less resume latency because it does not touch BIOS, and the processors are in idle state.

Compared with RTPM/idle,
PM_SUSPEND_FREEZE saves more power as
1. the processor has longer sleep time because processes are frozen. The deeper c-state the processor supports, more power saving we can get.
2. PM_SUSPEND_FREEZE uses system suspend code path, thus we can get more power saving from the devices that does not have good RTPM support.

This state is useful for
1) platforms that do not have STR, or have a broken STR.
2) platforms that have an extremely low power idle state, which can be used to replace STR.

The following describes how PM_SUSPEND_FREEZE state works.
1. echo freeze > /sys/power/state
2. the processes are frozen.
3. all the devices are suspended.
4. all the processors are blocked by a wait queue
5. all the processors idles and enters (Deep) c-state.
6. an interrupt fires.
7. a processor is woken up and handles the irq.
8. if it is a general event,
a) the irq handler runs and quites.
b) goto step 4.
9. if it is a real wake event, say, power button pressing, keyboard touch, mouse moving,
a) the irq handler runs and activate the wakeup source
b) wakeup_source_activate() notifies the wait queue.
c) system starts resuming from PM_SUSPEND_FREEZE
10. all the devices are resumed.
11. all the processes are unfrozen.
12. system is back to working.

Known Issue:
The wakeup of this new PM_SUSPEND_FREEZE state may behave differently from the previous suspend state.
Take ACPI platform for example, there are some GPEs that only enabled when the system is in sleep state, to wake the system backk from S3/S4. But we are not touching these GPEs during transition to PM_SUSPEND_FREEZE. This means we may lose some wake event.
But on the other hand, as we do not disable all the Interrupts during PM_SUSPEND_FREEZE, we may get some extra "wakeup" Interrupts, that are not available for S3/S4.

The patches has been tested on an old Sony laptop, and here are the results:

Average Power:
1. RPTM/idle for half an hour:

   14.8W, 12.6W, 14.1W, 12.5W, 14.4W, 13.2W, 12.9W
2. Freeze for half an hour:
   11W, 10.4W, 9.4W, 11.3W 10.5W
3. RTPM/idle for three hours:
   11.6W
4. Freeze for three hours:
   10W
5. Suspend to Memory:
   0.5~0.9W

Average Resume Latency:
1. RTPM/idle with a black screen: (From pressing keyboard to screen back) Less than 0.2s
2. Freeze: (From pressing power button to screen back)
2.50s
3. Suspend to Memory: (From pressing power button to screen back) 4.33s

Quoted 3 lines

From the results, we can see that all the platforms should benefit from this patch, even if it does not have Low Power S0.

fixed a build error when CONFIG_SUSPEND not set.
refreshed patch attached.

Quoted 1 line

From e784933534b8fc00b4e7b52f3c34ea9e614e513e Mon Sep 17 00:00:00 2001

From: Zhang Rui <[email protected]>
Date: Mon, 14 Jan 2013 11:12:53 +0800
Subject: [PATCH 1/3] PM: Introduce suspend state PM_SUSPEND_FREEZE

PM_SUSPEND_FREEZE state is a general state that does not need any platform specific support, it equals frozen processes + suspended devices + idle processors.

Compared with PM_SUSPEND_MEMORY,
PM_SUSPEND_FREEZE saves less power
because the system is still in a running state. PM_SUSPEND_FREEZE has less resume latency because it does not touch BIOS, and the processors are in idle state.

Compared with RTPM/idle,
PM_SUSPEND_FREEZE saves more power as
1. the processor has longer sleep time because processes are frozen. The deeper c-state the processor supports, more power saving we can get.
2. PM_SUSPEND_FREEZE uses system suspend code path, thus we can get more power saving from the devices that does not have good RTPM support.

This state is useful for
1) platforms that do not have STR, or have a broken STR.
2) platforms that have an extremely low power idle state, which can be used to replace STR.

The following describes how PM_SUSPEND_FREEZE state works.
1. echo freeze > /sys/power/state
2. the processes are frozen.
3. all the devices are suspended.
4. all the processors are blocked by a wait queue
5. all the processors idles and enters (Deep) c-state.
6. an interrupt fires.
7. a processor is woken up and handles the irq.
8. if it is a general event,
a) the irq handler runs and quites.
b) goto step 4.
9. if it is a real wake event, say, power button pressing, keyboard touch, mouse moving,
a) the irq handler runs and activate the wakeup source
b) wakeup_source_activate() notifies the wait queue.
c) system starts resuming from PM_SUSPEND_FREEZE
10. all the devices are resumed.
11. all the processes are unfrozen.
12. system is back to working.

Known Issue:
The wakeup of this new PM_SUSPEND_FREEZE state may behave differently from the previous suspend state.
Take ACPI platform for example, there are some GPEs that only enabled when the system is in sleep state, to wake the system backk from S3/S4. But we are not touching these GPEs during transition to PM_SUSPEND_FREEZE. This means we may lose some wake event.
But on the other hand, as we do not disable all the Interrupts during PM_SUSPEND_FREEZE, we may get some extra "wakeup" Interrupts, that are not available for S3/S4.

The patches has been tested on an old Sony laptop, and here are the results:

Average Power:
1. RPTM/idle for half an hour:
14.8W, 12.6W, 14.1W, 12.5W, 14.4W, 13.2W, 12.9W
2. Freeze for half an hour:
11W, 10.4W, 9.4W, 11.3W 10.5W
3. RTPM/idle for three hours:
11.6W
4. Freeze for three hours:
10W
5. Suspend to Memory:
0.5~0.9W

Average Resume Latency:
1. RTPM/idle with a black screen: (From pressing keyboard to screen back) Less than 0.2s
2. Freeze: (From pressing power button to screen back)
2.50s
3. Suspend to Memory: (From pressing power button to screen back) 4.33s

Quoted 1 line

From the results, we can see that all the platforms should benefit from

this patch, even if it does not have Low Power S0.

---
 drivers/base/power/wakeup.c |    6 ++++
 include/linux/suspend.h     |    6 +++-
 kernel/power/main.c         |    2 +-
 kernel/power/suspend.c      |   69 +++++++++++++++++++++++++++++++++++--------
 4 files changed, 68 insertions(+), 15 deletions(-)
drivers/base/power/wakeup.c +6 -0
index e6ee5e8..79715e7 100644
@@ -382,6 +382,12 @@ static void wakeup_source_activate(struct wakeup_source *ws)
 {
 	unsigned int cec;
 
+	/*
+	 * active wakeup source should bring the system
+	 * out of PM_SUSPEND_FREEZE state
+	 */
+	freeze_wake();
+
 	ws->active = true;
 	ws->active_count++;
 	ws->last_time = ktime_get();
include/linux/suspend.h +5 -1
index 0c808d7..d4e3f16 100644
@@ -34,8 +34,10 @@ static inline void pm_restore_console(void)
 typedef int __bitwise suspend_state_t;
 
 #define PM_SUSPEND_ON		((__force suspend_state_t) 0)
-#define PM_SUSPEND_STANDBY	((__force suspend_state_t) 1)
+#define PM_SUSPEND_FREEZE	((__force suspend_state_t) 1)
+#define PM_SUSPEND_STANDBY	((__force suspend_state_t) 2)
 #define PM_SUSPEND_MEM		((__force suspend_state_t) 3)
+#define PM_SUSPEND_MIN		PM_SUSPEND_FREEZE
 #define PM_SUSPEND_MAX		((__force suspend_state_t) 4)
 
 enum suspend_stat_step {
@@ -192,6 +194,7 @@ struct platform_suspend_ops {
  */
 extern void suspend_set_ops(const struct platform_suspend_ops *ops);
 extern int suspend_valid_only_mem(suspend_state_t state);
+extern void freeze_wake(void);
 
 /**
  * arch_suspend_disable_irqs - disable IRQs for suspend
@@ -217,6 +220,7 @@ extern int pm_suspend(suspend_state_t state);
 
 static inline void suspend_set_ops(const struct platform_suspend_ops *ops) {}
 static inline int pm_suspend(suspend_state_t state) { return -ENOSYS; }
+static inline void freeze_wake(void) {}
 #endif /* !CONFIG_SUSPEND */
 
 /* struct pbe is used for creating lists of pages that should be restored
kernel/power/main.c +1 -1
index 1c16f91..b1c26a9 100644
@@ -313,7 +313,7 @@ static ssize_t state_show(struct kobject *kobj, struct kobj_attribute *attr,
 static suspend_state_t decode_state(const char *buf, size_t n)
 {
 #ifdef CONFIG_SUSPEND
-	suspend_state_t state = PM_SUSPEND_STANDBY;
+	suspend_state_t state = PM_SUSPEND_MIN;
 	const char * const *s;
 #endif
 	char *p;
kernel/power/suspend.c +56 -13

162 lines not on this page · raw message

Signature · 1 line
1.7.9.5