hwmon: (ltc2978) Add support for LTC2974 and LTC3883
Subsystems (3)
Guenter Roeck
maintainerPATCH 2/2 hwmon: (ltc2978) Add support for LTC2974 and LTC3883
--- Documentation/hwmon/ltc2978 | 26 +++++--- drivers/hwmon/pmbus/Kconfig | 4 +- drivers/hwmon/pmbus/ltc2978.c | 136 +++++++++++++++++++++++++++++++++++++---- 3 files changed, 143 insertions(+), 23 deletions(-)
Documentation/hwmon/ltc2978 +17 -9
@@ -2,6 +2,10 @@ Kernel driver ltc2978 ========== Supported chips: + * Linear Technology LTC2974 + Prefix: 'ltc2974' + Addresses scanned: - + Datasheet: http://cds.linear.com/docs/en/datasheet/2974f.pdf * Linear Technology LTC2978 Prefix: 'ltc2978' Addresses scanned: -
@@ -10,6 +14,10 @@ Supported chips: Prefix: 'ltc3880' Addresses scanned: - Datasheet: http://cds.linear.com/docs/en/datasheet/3880fa.pdf + * Linear Technology LTC3883 + Prefix: 'ltc3883' + Addresses scanned: - + Datasheet: http://cds.linear.com/docs/en/datasheet/3883f.pdf Author: Guenter Roeck <[email protected]>
@@ -17,9 +25,9 @@ Author: Guenter Roeck <[email protected]> Description ----------- -The LTC2978 is an octal power supply monitor, supervisor, sequencer and -margin controller. The LTC3880 is a dual, PolyPhase DC/DC synchronous -step-down switching regulator controller. +LTC2974 is a quad digital power supply manager. LTC2978 is an octal power supply +monitor. LTC3880 is a dual output poly-phase step-down DC/DC controller. LTC3883 +is a single phase step-down DC/DC controller. Usage Notes
@@ -48,7 +56,7 @@ in1_min_alarm Input voltage low alarm. in1_max_alarm Input voltage high alarm. in1_lcrit_alarm Input voltage critical low alarm. in1_crit_alarm Input voltage critical high alarm. -in1_lowest Lowest input voltage. LTC2978 only. +in1_lowest Lowest input voltage. LTC2974 and LTC2978 only. in1_highest Highest input voltage. in1_reset_history Reset history. Writing into this attribute will reset history for all attributes.
@@ -63,7 +71,7 @@ in[2-9]_min_alarm Output voltage low alarm. in[2-9]_max_alarm Output voltage high alarm. in[2-9]_lcrit_alarm Output voltage critical low alarm. in[2-9]_crit_alarm Output voltage critical high alarm. -in[2-9]_lowest Lowest output voltage. LTC2978 only. +in[2-9]_lowest Lowest output voltage. LTC2974 and LTC2978 only. in[2-9]_highest Lowest output voltage. in[2-9]_reset_history Reset history. Writing into this attribute will reset history for all attributes.
@@ -82,20 +90,20 @@ temp[1-3]_min_alarm Chip temperature low alarm. temp[1-3]_max_alarm Chip temperature high alarm. temp[1-3]_lcrit_alarm Chip temperature critical low alarm. temp[1-3]_crit_alarm Chip temperature critical high alarm. -temp[1-3]_lowest Lowest measured temperature. LTC2978 only. +temp[1-3]_lowest Lowest measured temperature. LTC2974 and LTC2978 only. temp[1-3]_highest Highest measured temperature. temp[1-3]_reset_history Reset history. Writing into this attribute will reset history for all attributes. -power[1-2]_label "pout[1-2]". LTC3880 only. +power[1-2]_label "pout[1-2]". LTC2974, LTC3880, LTC3883 only. power[1-2]_input Measured power. -curr1_label "iin". LTC3880 only. +curr1_label "iin". LTC3880 and LTC3883 only. curr1_input Measured input current. curr1_max Maximum input current. curr1_max_alarm Input current high alarm. -curr[2-3]_label "iout[1-2]". LTC3880 only. +curr[2-3]_label "iout[1-2]". LTC3880 and LTC3883 only. curr[2-3]_input Measured input current. curr[2-3]_max Maximum input current. curr[2-3]_crit Critical input current.
drivers/hwmon/pmbus/Kconfig +2 -2
@@ -48,11 +48,11 @@ config SENSORS_LM25066 be called lm25066. config SENSORS_LTC2978 - tristate "Linear Technologies LTC2978 and LTC3880" + tristate "Linear Technologies LTC2974, LTC2978, LTC3880, and LTC3883" default n help If you say yes here you get hardware monitoring support for Linear - Technology LTC2978 and LTC3880. + Technology LTC2974, LTC2978, LTC3880, and LTC3883. This driver can also be built as a module. If so, the module will be called ltc2978.
drivers/hwmon/pmbus/ltc2978.c +124 -12
233 lines not on this page · raw message
Signature · 7 lines
1.7.9.7 _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Hi Guenter,
Quoted 6 lines · Guenter Roeck
Signed-off-by Guenter Roeck <[email protected]>--- Documentation/hwmon/ltc2978 | 26 +++++--- drivers/hwmon/pmbus/Kconfig | 4 +- drivers/hwmon/pmbus/ltc2978.c | 136 +++++++++++++++++++++++++++++++++++++---- 3 files changed, 143 insertions(+), 23 deletions(-)
Not being familiar with pmbus, my review may be incomplete, but I did my best.
Quoted 16 lines
Documentation/hwmon/ltc2978 +4
-0@@ -2,6 +2,10 @@ Kernel driver ltc2978 ==========> Supported chips: + * Linear Technology LTC2974 + Prefix: 'ltc2974' + Addresses scanned: - + Datasheet: http://cds.linear.com/docs/en/datasheet/2974f.pdf * Linear Technology LTC2978 Prefix: 'ltc2978' Addresses scanned: -
Documentation/hwmon/ltc2978 Supported chips: · line 22
Quoted 9 lines
Documentation/hwmon/ltc2978 +4
-0@@ -10,6 +14,10 @@ Supported chips: Prefix: 'ltc3880' Addresses scanned: - Datasheet: http://cds.linear.com/docs/en/datasheet/3880fa.pdf + * Linear Technology LTC3883 + Prefix: 'ltc3883' + Addresses scanned: - + Datasheet: http://cds.linear.com/docs/en/datasheet/3883f.pdf Author: Guenter Roeck <[email protected]>
You might want to update this e-mail address. This might be better done as a tree-wide patch though.
Documentation/hwmon/ltc2978 in[2-9]_min_alarm Output voltage low alarm.
Quoted 24 lines
Documentation/hwmon/ltc2978 +4
-4@@ -17,9 +25,9 @@ Author: Guenter Roeck <[email protected]> Description ----------- -The LTC2978 is an octal power supply monitor, supervisor, sequencer and -margin controller. The LTC3880 is a dual, PolyPhase DC/DC synchronous -step-down switching regulator controller. +LTC2974 is a quad digital power supply manager. LTC2978 is an octal power supply +monitor. LTC3880 is a dual output poly-phase step-down DC/DC controller. LTC3883 +is a single phase step-down DC/DC controller. Usage Notes@@ -48,7 +56,7 @@ in1_min_alarm Input voltage low alarm. in1_max_alarm Input voltage high alarm. in1_lcrit_alarm Input voltage critical low alarm. in1_crit_alarm Input voltage critical high alarm. -in1_lowest Lowest input voltage. LTC2978 only. +in1_lowest Lowest input voltage. LTC2974 and LTC2978 only. in1_highest Highest input voltage. in1_reset_history Reset history. Writing into this attribute will reset history for all attributes.@@ -63,7 +71,7 @@ in[2-9]_min_alarm Output voltage low alarm.
in[2-9]_label says "Channels 3 to 9 on LTC2978 only" but I suppose channels 3 to 5 are also available on LTC2974?
Documentation/hwmon/ltc2978 temp[1-3]_min_alarm Chip temperature low alarm.
Quoted 9 lines
Documentation/hwmon/ltc2978 +1
-1in[2-9]_max_alarm Output voltage high alarm. in[2-9]_lcrit_alarm Output voltage critical low alarm. in[2-9]_crit_alarm Output voltage critical high alarm. -in[2-9]_lowest Lowest output voltage. LTC2978 only. +in[2-9]_lowest Lowest output voltage. LTC2974 and LTC2978 only. in[2-9]_highest Lowest output voltage. in[2-9]_reset_history Reset history. Writing into this attribute will reset history for all attributes.@@ -82,20 +90,20 @@ temp[1-3]_min_alarm Chip temperature low alarm.
temp[1-3]_input has a detailed description of the input mappings for the LTC2978 and LTC3880, it would seem desirable to have a similar description for the two new chips LTC2974 and LTC3883.
Documentation/hwmon/ltc2978 temp[1-3]_min_alarm Chip temperature low alarm. · line 98
Quoted 11 lines
Documentation/hwmon/ltc2978 +2
-2temp[1-3]_max_alarm Chip temperature high alarm. temp[1-3]_lcrit_alarm Chip temperature critical low alarm. temp[1-3]_crit_alarm Chip temperature critical high alarm. -temp[1-3]_lowest Lowest measured temperature. LTC2978 only. +temp[1-3]_lowest Lowest measured temperature. LTC2974 and LTC2978 only. temp[1-3]_highest Highest measured temperature. temp[1-3]_reset_history Reset history. Writing into this attribute will reset history for all attributes. -power[1-2]_label "pout[1-2]". LTC3880 only. +power[1-2]_label "pout[1-2]". LTC2974, LTC3880, LTC3883 only.
I am under the impression that LTC2974 has pout[3-4] as well?
Documentation/hwmon/ltc2978 temp[1-3]_min_alarm Chip temperature low alarm. · line 106
Quoted 10 lines
Documentation/hwmon/ltc2978 +2
-2power[1-2]_input Measured power. -curr1_label "iin". LTC3880 only. +curr1_label "iin". LTC3880 and LTC3883 only. curr1_input Measured input current. curr1_max Maximum input current. curr1_max_alarm Input current high alarm. -curr[2-3]_label "iout[1-2]". LTC3880 only. +curr[2-3]_label "iout[1-2]". LTC3880 and LTC3883 only.
What about LTC2974? It has PMBUS_HAVE_IOUT on all 4 pages, doesn't this translate to curr[2-5]_* files? This would correlate with the size increase of data->iout_min/max from 2 to 4 elements.
Quoted 9 lines
Documentation/hwmon/ltc2978 +0
-0curr[2-3]_input Measured input current. curr[2-3]_max Maximum input current. curr[2-3]_crit Critical input current.drivers/hwmon/pmbus/ltc2978.c +0
-0
drivers/hwmon/pmbus/ltc2978.c line 4
Quoted 5 lines
drivers/hwmon/pmbus/ltc2978.c +1
-1@@ -1,5 +1,5 @@/* -* Hardware monitoring driver for LTC2978 and LTC3880 +* Hardware monitoring driver for LTC2974, LTC2978, LTC3880, and LTC3883 * * Copyright (c) 2011 Ericsson AB.
Feel free to add your name and copyright here, with the new year.
Quoted 23 lines
drivers/hwmon/pmbus/ltc2978.c +4
-4* @@ -26,28 +26,42 @@#include <linux/i2c.h> #include "pmbus.h" -enum chips { ltc2978, ltc3880 }; +enum chips { ltc2974, ltc2978, ltc3880, ltc3883 }; -/* LTC2978 and LTC3880 */ +/* Common for all chips */ #define LTC2978_MFR_VOUT_PEAK 0xdd#define LTC2978_MFR_VIN_PEAK 0xde#define LTC2978_MFR_TEMPERATURE_PEAK 0xdf#define LTC2978_MFR_SPECIAL_ID 0xe7 -/* LTC2978 only */ +/* LTC2974 and LTC2978 */ #define LTC2978_MFR_VOUT_MIN 0xfb#define LTC2978_MFR_VIN_MIN 0xfc#define LTC2978_MFR_TEMPERATURE_MIN 0xfd -/* LTC3880 only */ +/* LTC3880 and LTC3883 */
drivers/hwmon/pmbus/ltc2978.c line 52
Quoted 10 lines
drivers/hwmon/pmbus/ltc2978.c +6
-0#define LTC3880_MFR_IOUT_PEAK 0xd7#define LTC3880_MFR_CLEAR_PEAKS 0xe3#define LTC3880_MFR_TEMPERATURE2_PEAK 0xf4 +/* LTC3883 only */ +#define LTC3883_MFR_IIN_PEAK 0xe1 + +/* LTC2974 only */ +#define LTC2974_MFR_IOUT_PEAK 0xd7 +#define LTC2974_MFR_IOUT_MIN 0xd8
As you have two sub-families (LTC2974/8 vs. LTC3880/3) it would be clearer to group "LTC2974 only" register definitions with "LTC2974 and LTC2978" register definitions (i.e. move this one block two blocks up.)
Quoted 16 lines
drivers/hwmon/pmbus/ltc2978.c +8
-0+ +#define LTC2974_ID 0x0212#define LTC2978_ID_REV1 0x0121#define LTC2978_ID_REV2 0x0122#define LTC3880_ID 0x4000#define LTC3880_ID_MASK 0xff00 +#define LTC3883_ID 0x4300 + +#define LTC2974_NUM_PAGES 4 +#define LTC2978_NUM_PAGES 8 +#define LTC3880_NUM_PAGES 2 +#define LTC3883_NUM_PAGES 1/* * LTC2978 clears peak data whenever the CLEAR_FAULTS command is executed, which
drivers/hwmon/pmbus/ltc2978.c struct ltc2978_data { · line 80
Quoted 7 lines
drivers/hwmon/pmbus/ltc2978.c +3
-1@@ -61,7 +75,9 @@ struct ltc2978_data {int vin_min, vin_max;int temp_min, temp_max;int vout_min[8 ], vout_max[8 ]; -int iout_max[2 ]; +int iin_max; +int iout_max[4 ]; +int iout_min[4 ];
Nitpicking:
int iout_min[4], iout_max[4];
would match the existing coding style.
Quoted 62 lines
drivers/hwmon/pmbus/ltc2978.c +48
-0int temp2_max[2 ];struct pmbus_driver_info info; };@@ -184,6 +200,38 @@ static int ltc2978_read_word_data(struct i2c_client *client, int page, int reg)return ret; } +static int ltc2974_read_word_data (struct i2c_client *client,int page,int reg) +{ +const struct pmbus_driver_info *info =pmbus_get_driver_info (client); +struct ltc2978_data *data =to_ltc2978_data (info); +int ret; + +switch (reg) { +case PMBUS_VIRT_READ_IOUT_MAX : + ret =pmbus_read_word_data (client, page,LTC2974_MFR_IOUT_PEAK ); +if (ret >=0 ) { +if (lin11_to_val (ret) + >lin11_to_val (data->iout_max[page])) + data->iout_max[page] = ret; + ret = data->iout_max[page]; + } +break ; +case PMBUS_VIRT_READ_IOUT_MIN : + ret =pmbus_read_word_data (client, page,LTC2974_MFR_IOUT_MIN ); +if (ret >=0 ) { +if (lin11_to_val (ret) + <lin11_to_val (data->iout_min[page])) + data->iout_min[page] = ret; + ret = data->iout_min[page]; + } +break ; +default : + ret =ltc2978_read_word_data (client, page, reg); +break ; + } +return ret; +} +static int ltc3880_read_word_data (struct i2c_client *client,int page,int reg) {const struct pmbus_driver_info *info =pmbus_get_driver_info (client);@@ -226,6 +274,29 @@ static int ltc3880_read_word_data(struct i2c_client *client, int page, int reg)return ret; } +static int ltc3883_read_word_data (struct i2c_client *client,int page,int reg) +{ +const struct pmbus_driver_info *info =pmbus_get_driver_info (client); +struct ltc2978_data *data =to_ltc2978_data (info); +int ret; + +switch (reg) { +case PMBUS_VIRT_READ_IIN_MAX : + ret =pmbus_read_word_data (client, page,LTC3883_MFR_IIN_PEAK ); +if (ret >=0 ) { +if (lin11_to_val (ret) + >lin11_to_val (data->iin_max)) + data->iin_max = ret; + ret = data->iin_max; + } +break ;
drivers/hwmon/pmbus/ltc2978.c static int ltc3880_read_word_data(struct i2c_client *client, int page, int reg) · line 302
Quoted 10 lines
drivers/hwmon/pmbus/ltc2978.c +7
-0+default : + ret =ltc3880_read_word_data (client, page, reg); +break ; + } +return ret; +} +static int ltc2978_clear_peaks (struct i2c_client *client,int page,enum chips id) {
In function ltc2978_clear_peaks() the test on "id" looks wrong:
if (id = ltc2978) ret = pmbus_write_byte(client, page, PMBUS_CLEAR_FAULTS); else ret = pmbus_write_byte(client, 0, LTC3880_MFR_CLEAR_PEAKS);
LTC2974 doesn't have LTC3880_MFR_CLEAR_PEAKS, the address is used for a different register, still you'll write to this register for that chip. No good.
In order to avoid this from happening again when adding support for new chips, I'd suggest reverting the test to:
if (id = ltc3880 || id = ltc3883) ret = pmbus_write_byte(client, 0, LTC3880_MFR_CLEAR_PEAKS); else ret = pmbus_write_byte(client, page, PMBUS_CLEAR_FAULTS);
drivers/hwmon/pmbus/ltc2978.c static int ltc2978_write_word_data(struct i2c_client *client, int page, · line 326
Quoted 10 lines
drivers/hwmon/pmbus/ltc2978.c +6
-0@@ -247,8 +318,17 @@ static int ltc2978_write_word_data(struct i2c_client *client, int page,int ret;switch (reg) { +case PMBUS_VIRT_RESET_IIN_HISTORY : +if (data->id != ltc3883) { + ret = -ENODATA ; +break ; + } + data->iin_max =0xffff ;
This initial value is inconsistent with the iout_max one below (both the original one and the new one.) If I understand the L11 format correctly, 0xffff corresponds to the closest negative value to 0 (-1 * 2^(-15)), right? If negative values are supported I'd expect you to put the most negative value (largest in absolute value) possible here, which would be 0x7c00 (exponent = 15, sign = 1, mantissa = 0.) If negative values aren't supported then 0 would do?
drivers/hwmon/pmbus/ltc2978.c static int ltc2978_write_word_data(struct i2c_client *client, int page, · line 331
Quoted 6 lines
drivers/hwmon/pmbus/ltc2978.c +4
-1+ ret =ltc2978_clear_peaks (client, page, data->id); +break ;case PMBUS_VIRT_RESET_IOUT_HISTORY : - data->iout_max[page] =0x7fff ; + data->iout_min[page] =0xffff ; + data->iout_max[page] =0 ;
This change looks suspicious, can you explain it? It seems to be unrelated to the support of new chips. If it is a bug fix, it should be split to a separate patch.
I noticed that the driver has inconsistent initial values for iin_max, iout_min and temp2_max, between the probe function and the history reset code. In fact iin_max, iout_min and temp2_max have no explicit initial value in the probe path, so they default to 0, while history reset sets explicit values. This was the case for iout_max too before the change above. This looks wrong.
Several L11-formatted initial values look wrong to me as well. I suggest sorting this out first, both the consistency and the values themselves, and only after this is done, adding support for the new chips. As I understand it, for L11-formatted registers, min should be set to 0x7bff and max should be set to 0x7c00.
Quoted 31 lines
drivers/hwmon/pmbus/ltc2978.c +7
-1ret =ltc2978_clear_peaks (client, page, data->id);break ;case PMBUS_VIRT_RESET_TEMP2_HISTORY :@@ -278,8 +358,10 @@ static int ltc2978_write_word_data(struct i2c_client *client, int page, }static const struct i2c_device_id ltc2978_id[] = { + {"ltc2974" , ltc2974}, {"ltc2978" , ltc2978}, {"ltc3880" , ltc3880}, + {"ltc3883" , ltc3883}, {} };MODULE_DEVICE_TABLE (i2c, ltc2978_id);@@ -304,10 +386,14 @@ static int ltc2978_probe(struct i2c_client *client,if (chip_id <0 )return chip_id; -if (chip_id =LTC2978_ID_REV1 || chip_id =LTC2978_ID_REV2 ) { +if (chip_id =LTC2974_ID ) { + data->id = ltc2974; + }else if (chip_id =LTC2978_ID_REV1 || chip_id =LTC2978_ID_REV2 ) { data->id = ltc2978; }else if ((chip_id <C3880_ID_MASK ) =LTC3880_ID ) { data->id = ltc3880; + }else if ((chip_id <C3880_ID_MASK ) =LTC3883_ID ) { + data->id = ltc3883; }else {dev_err (&client->dev,"Unsupported chip ID 0x%x\n" , chip_id);return -ENODEV ;
drivers/hwmon/pmbus/ltc2978.c static int ltc2978_probe(struct i2c_client *client, · line 419
Quoted 7 lines
drivers/hwmon/pmbus/ltc2978.c +4
-0@@ -327,13 +413,29 @@ static int ltc2978_probe(struct i2c_client *client, data->temp_max =0x7fff ;switch (id->driver_data) { +case ltc2974: + info->read_word_data = ltc2974_read_word_data; + info->pages =LTC2974_NUM_PAGES ; + info->func[0 ] =PMBUS_HAVE_VIN |PMBUS_HAVE_IOUT
No PMBUS_HAVE_STATUS_IOUT here?
Quoted 57 lines
drivers/hwmon/pmbus/ltc2978.c +26
-4+ | PMBUS_HAVE_STATUS_INPUT + |PMBUS_HAVE_VOUT |PMBUS_HAVE_STATUS_VOUT + |PMBUS_HAVE_POUT |PMBUS_HAVE_TEMP2 + |PMBUS_HAVE_TEMP |PMBUS_HAVE_STATUS_TEMP ; +for (i =1 ; i < info->pages; i++) { + info->func[i] =PMBUS_HAVE_VOUT + |PMBUS_HAVE_STATUS_VOUT |PMBUS_HAVE_POUT + |PMBUS_HAVE_TEMP |PMBUS_HAVE_STATUS_TEMP + |PMBUS_HAVE_IOUT |PMBUS_HAVE_STATUS_IOUT ; + data->vout_min[i] =0xffff ; + } +break ;case ltc2978: info->read_word_data = ltc2978_read_word_data; - info->pages =8 ; + info->pages =LTC2978_NUM_PAGES ; info->func[0 ] =PMBUS_HAVE_VIN |PMBUS_HAVE_STATUS_INPUT |PMBUS_HAVE_VOUT |PMBUS_HAVE_STATUS_VOUT |PMBUS_HAVE_TEMP |PMBUS_HAVE_STATUS_TEMP ; -for (i =1 ; i <8 ; i++) { +for (i =1 ; i < info->pages; i++) { info->func[i] =PMBUS_HAVE_VOUT |PMBUS_HAVE_STATUS_VOUT ; data->vout_min[i] =0xffff ;@@ -341,7 +443,7 @@ static int ltc2978_probe(struct i2c_client *client,break ;case ltc3880: info->read_word_data = ltc3880_read_word_data; - info->pages =2 ; + info->pages =LTC3880_NUM_PAGES ; info->func[0 ] =PMBUS_HAVE_VIN |PMBUS_HAVE_IIN |PMBUS_HAVE_STATUS_INPUT |PMBUS_HAVE_VOUT |PMBUS_HAVE_STATUS_VOUT @@ -354,6 +456,16 @@ static int ltc2978_probe(struct i2c_client *client, | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP; data->vout_min[1 ] =0xffff ;break ; +case ltc3883: + info->read_word_data = ltc3883_read_word_data; + info->pages =LTC3883_NUM_PAGES ; + info->func[0 ] =PMBUS_HAVE_VIN |PMBUS_HAVE_IIN + |PMBUS_HAVE_STATUS_INPUT + |PMBUS_HAVE_VOUT |PMBUS_HAVE_STATUS_VOUT + |PMBUS_HAVE_IOUT |PMBUS_HAVE_STATUS_IOUT + |PMBUS_HAVE_POUT |PMBUS_HAVE_TEMP + |PMBUS_HAVE_TEMP2 |PMBUS_HAVE_STATUS_TEMP ; +break ;default :return -ENODEV ; }@@ -374,5 +486,5 @@ static struct i2c_driver ltc2978_driver = {module_i2c_driver (ltc2978_driver);MODULE_AUTHOR ("Guenter Roeck" ); -MODULE_DESCRIPTION ("PMBus driver for LTC2978 and LTC3880" ); +MODULE_DESCRIPTION ("PMBus driver for LTC2974, LTC2978, LTC3880, and LTC3883" );MODULE_LICENSE ("GPL" );
Signature · 6 lines
Jean Delvare _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Guenter Roeck
maintainerQuoted 10 lines · Jean Delvare
Hi Guenter,
Quoted 6 lines · Guenter Roeck
Signed-off-by Guenter Roeck <[email protected]>--- Documentation/hwmon/ltc2978 | 26 +++++--- drivers/hwmon/pmbus/Kconfig | 4 +- drivers/hwmon/pmbus/ltc2978.c | 136 +++++++++++++++++++++++++++++++++++++---- 3 files changed, 143 insertions(+), 23 deletions(-)
Quoted 3 lines
Not being familiar with pmbus, my review may be incomplete, but I did my best.
Hi Jean,
Excellent review anyway, as always ...
Quoted 93 lines
Quoted 16 lines
Documentation/hwmon/ltc2978 +4
-0@@ -2,6 +2,10 @@ Kernel driver ltc2978 ==========> > Supported chips: + * Linear Technology LTC2974 + Prefix: 'ltc2974' + Addresses scanned: - + Datasheet: http://cds.linear.com/docs/en/datasheet/2974f.pdf * Linear Technology LTC2978 Prefix: 'ltc2978' Addresses scanned: -Documentation/hwmon/ltc2978 Supported chips: · line 22
Quoted 9 lines
Documentation/hwmon/ltc2978 +4
-0@@ -10,6 +14,10 @@ Supported chips: Prefix: 'ltc3880' Addresses scanned: - Datasheet: http://cds.linear.com/docs/en/datasheet/3880fa.pdf + * Linear Technology LTC3883 + Prefix: 'ltc3883' + Addresses scanned: - + Datasheet: http://cds.linear.com/docs/en/datasheet/3883f.pdf Author: Guenter Roeck <[email protected]>You might want to update this e-mail address. This might be better done as a tree-wide patch though.
Documentation/hwmon/ltc2978 in[2-9]_min_alarm Output voltage low alarm.
Quoted 24 lines
Documentation/hwmon/ltc2978 +4
-4@@ -17,9 +25,9 @@ Author: Guenter Roeck <[email protected]> Description ----------- -The LTC2978 is an octal power supply monitor, supervisor, sequencer and -margin controller. The LTC3880 is a dual, PolyPhase DC/DC synchronous -step-down switching regulator controller. +LTC2974 is a quad digital power supply manager. LTC2978 is an octal power supply +monitor. LTC3880 is a dual output poly-phase step-down DC/DC controller. LTC3883 +is a single phase step-down DC/DC controller. Usage Notes@@ -48,7 +56,7 @@ in1_min_alarm Input voltage low alarm. in1_max_alarm Input voltage high alarm. in1_lcrit_alarm Input voltage critical low alarm. in1_crit_alarm Input voltage critical high alarm. -in1_lowest Lowest input voltage. LTC2978 only. +in1_lowest Lowest input voltage. LTC2974 and LTC2978 only. in1_highest Highest input voltage. in1_reset_history Reset history. Writing into this attribute will reset history for all attributes.@@ -63,7 +71,7 @@ in[2-9]_min_alarm Output voltage low alarm.in[2-9]_label says "Channels 3 to 9 on LTC2978 only" but I suppose channels 3 to 5 are also available on LTC2974?
Documentation/hwmon/ltc2978 temp[1-3]_min_alarm Chip temperature low alarm.
Quoted 9 lines
Documentation/hwmon/ltc2978 +1
-1in[2-9]_max_alarm Output voltage high alarm. in[2-9]_lcrit_alarm Output voltage critical low alarm. in[2-9]_crit_alarm Output voltage critical high alarm. -in[2-9]_lowest Lowest output voltage. LTC2978 only. +in[2-9]_lowest Lowest output voltage. LTC2974 and LTC2978 only. in[2-9]_highest Lowest output voltage. in[2-9]_reset_history Reset history. Writing into this attribute will reset history for all attributes.@@ -82,20 +90,20 @@ temp[1-3]_min_alarm Chip temperature low alarm.temp[1-3]_input has a detailed description of the input mappings for the LTC2978 and LTC3880, it would seem desirable to have a similar description for the two new chips LTC2974 and LTC3883.
Documentation/hwmon/ltc2978 temp[1-3]_min_alarm Chip temperature low alarm. · line 98
Quoted 11 lines
Documentation/hwmon/ltc2978 +2
-2temp[1-3]_max_alarm Chip temperature high alarm. temp[1-3]_lcrit_alarm Chip temperature critical low alarm. temp[1-3]_crit_alarm Chip temperature critical high alarm. -temp[1-3]_lowest Lowest measured temperature. LTC2978 only. +temp[1-3]_lowest Lowest measured temperature. LTC2974 and LTC2978 only. temp[1-3]_highest Highest measured temperature. temp[1-3]_reset_history Reset history. Writing into this attribute will reset history for all attributes. -power[1-2]_label "pout[1-2]". LTC3880 only. +power[1-2]_label "pout[1-2]". LTC2974, LTC3880, LTC3883 only.I am under the impression that LTC2974 has pout[3-4] as well?
Quoted 8 lines
Documentation/hwmon/ltc2978 +1
-1power[1-2]_input Measured power. -curr1_label "iin". LTC3880 only. +curr1_label "iin". LTC3880 and LTC3883 only. curr1_input Measured input current. curr1_max Maximum input current. curr1_max_alarm Input current high alarm.
Quoted 7 lines
Documentation/hwmon/ltc2978 temp[1-3]_min_alarm Chip temperature low alarm. · line 106
Quoted 2 lines
Documentation/hwmon/ltc2978 +1
-1-curr[2-3]_label "iout[1-2]". LTC3880 only. +curr[2-3]_label "iout[1-2]". LTC3880 and LTC3883 only.What about LTC2974? It has
PMBUS_HAVE_IOUTon all 4 pages, doesn't this translate to curr[2-5]_* files? This would correlate with the size increase of data->iout_min/max from 2 to 4 elements.
I have been wondering if I should create per device attribute lists. Things are getting confusing. Do you think that would make sense / be better ?
Other comments are all valid ... I pulled the code from 3.9 and will have another look. Especially regarding the peak values - yes, I noticed at some point that something is wrong with the initialization, but then forgot to follow up on it. Oh well :(.
Thanks,
Guenter
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Quoted 59 lines · Guenter Roeck
Quoted 51 lines · Jean Delvare
Documentation/hwmon/ltc2978 in[2-9]_min_alarm Output voltage low alarm.
Quoted 10 lines · Guenter Roeck
Documentation/hwmon/ltc2978 +1
-1@@ -48,7 +56,7 @@ in1_min_alarm Input voltage low alarm. in1_max_alarm Input voltage high alarm. in1_lcrit_alarm Input voltage critical low alarm. in1_crit_alarm Input voltage critical high alarm. -in1_lowest Lowest input voltage. LTC2978 only. +in1_lowest Lowest input voltage. LTC2974 and LTC2978 only. in1_highest Highest input voltage. in1_reset_history Reset history. Writing into this attribute will reset history for all attributes.@@ -63,7 +71,7 @@ in[2-9]_min_alarm Output voltage low alarm.in[2-9]_label says "Channels 3 to 9 on LTC2978 only" but I suppose channels 3 to 5 are also available on LTC2974?
Documentation/hwmon/ltc2978 temp[1-3]_min_alarm Chip temperature low alarm.
Quoted 9 lines
Documentation/hwmon/ltc2978 +1
-1in[2-9]_max_alarm Output voltage high alarm. in[2-9]_lcrit_alarm Output voltage critical low alarm. in[2-9]_crit_alarm Output voltage critical high alarm. -in[2-9]_lowest Lowest output voltage. LTC2978 only. +in[2-9]_lowest Lowest output voltage. LTC2974 and LTC2978 only. in[2-9]_highest Lowest output voltage. in[2-9]_reset_history Reset history. Writing into this attribute will reset history for all attributes.@@ -82,20 +90,20 @@ temp[1-3]_min_alarm Chip temperature low alarm.temp[1-3]_input has a detailed description of the input mappings for the LTC2978 and LTC3880, it would seem desirable to have a similar description for the two new chips LTC2974 and LTC3883.
Documentation/hwmon/ltc2978 temp[1-3]_min_alarm Chip temperature low alarm. · line 98
Quoted 11 lines
Documentation/hwmon/ltc2978 +2
-2temp[1-3]_max_alarm Chip temperature high alarm. temp[1-3]_lcrit_alarm Chip temperature critical low alarm. temp[1-3]_crit_alarm Chip temperature critical high alarm. -temp[1-3]_lowest Lowest measured temperature. LTC2978 only. +temp[1-3]_lowest Lowest measured temperature. LTC2974 and LTC2978 only. temp[1-3]_highest Highest measured temperature. temp[1-3]_reset_history Reset history. Writing into this attribute will reset history for all attributes. -power[1-2]_label "pout[1-2]". LTC3880 only. +power[1-2]_label "pout[1-2]". LTC2974, LTC3880, LTC3883 only.I am under the impression that LTC2974 has pout[3-4] as well?
Quoted 8 lines
Documentation/hwmon/ltc2978 +1
-1power[1-2]_input Measured power. -curr1_label "iin". LTC3880 only. +curr1_label "iin". LTC3880 and LTC3883 only. curr1_input Measured input current. curr1_max Maximum input current. curr1_max_alarm Input current high alarm.Quoted 6 lines
Documentation/hwmon/ltc2978 temp[1-3]_min_alarm Chip temperature low alarm. · line 106
Quoted 2 lines
Documentation/hwmon/ltc2978 +1
-1-curr[2-3]_label "iout[1-2]". LTC3880 only. +curr[2-3]_label "iout[1-2]". LTC3880 and LTC3883 only.What about LTC2974? It has
PMBUS_HAVE_IOUTon all 4 pages, doesn't this translate to curr[2-5]_* files? This would correlate with the size increase of data->iout_min/max from 2 to 4 elements.
Quoted 2 lines
I have been wondering if I should create per device attribute lists. Things are getting confusing. Do you think that would make sense / be better ?
There are pros and cons each way, as you have already found out I'm sure. I do not have a strong opinion. Maybe take the middle road, and make one section for LTC297x and one for LTC388x?
Quoted 4 lines
Other comments are all valid ... I pulled the code from 3.9 and will have another look. Especially regarding the peak values - yes, I noticed at some point that something is wrong with the initialization, but then forgot to follow up on it. Oh well :(.
Signature · 6 lines
Jean Delvare _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Guenter Roeck
maintainerPATCH 2/2 hwmon: (ltc2978) Add support for LTC3882
In reply to Guenter RoeckLTC3882 is mostly compatible with LTC3880. Major differences are that it does not measure the input current, and it no longer supports LTC's legacy mechanism to identify the chip.
--- .../devicetree/bindings/hwmon/ltc2978.txt | 3 +- Documentation/hwmon/ltc2978 | 26 ++++++----- drivers/hwmon/pmbus/ltc2978.c | 50 +++++++++++++++++++--- 3 files changed, 62 insertions(+), 17 deletions(-)
Documentation/devicetree/bindings/hwmon/ltc2978.txt +2 -1
@@ -6,6 +6,7 @@ Required properties: * "lltc,ltc2977" * "lltc,ltc2978" * "lltc,ltc3880" + * "lltc,ltc3882" * "lltc,ltc3883" * "lltc,ltm4676" - reg: I2C slave address
@@ -20,7 +21,7 @@ Valid names of regulators depend on number of supplies supported per device: * ltc2974 : vout0 - vout3 * ltc2977 : vout0 - vout7 * ltc2978 : vout0 - vout7 - * ltc3880 : vout0 - vout1 + * ltc3880, ltc3882 : vout0 - vout1 * ltc3883 : vout0 * ltm4676 : vout0 - vout1
Documentation/hwmon/ltc2978 +16 -10
@@ -19,6 +19,10 @@ Supported chips: Prefix: 'ltc3880' Addresses scanned: - Datasheet: http://www.linear.com/product/ltc3880 + * Linear Technology LTC3882 + Prefix: 'ltc3882' + Addresses scanned: - + Datasheet: http://www.linear.com/product/ltc3882 * Linear Technology LTC3883 Prefix: 'ltc3883' Addresses scanned: -
@@ -34,11 +38,12 @@ Author: Guenter Roeck <[email protected]> Description ----------- -LTC2974 is a quad digital power supply manager. LTC2978 is an octal power supply -monitor. LTC2977 is a pin compatible replacement for LTC2978. LTC3880 is a dual -output poly-phase step-down DC/DC controller. LTC3883 is a single phase -step-down DC/DC controller. LTM4676 is a dual 13A or single 26A uModule -regulator. +LTC2974 is a quad digital power supply managers. +LTC2978 is an octal power supply monitor. +LTC2977 is a pin compatible replacement for LTC2978. +LTC3880 and LTC3882 are dual output poly-phase step-down DC/DC controllers. +LTC3883 is a single phase step-down DC/DC controller. +LTM4676 is a dual 13A or single 26A uModule regulator. Usage Notes
@@ -80,7 +85,7 @@ in[N]_label "vout[1-8]". LTC2974: N=2-5 LTC2977: N=2-9 LTC2978: N=2-9 - LTC3880, LTM4676: N=2-3 + LTC3880, LTC3882, LTM4676: N=2-3 LTC3883: N=2 in[N]_input Measured output voltage. in[N]_min Minimum output voltage.
@@ -100,8 +105,9 @@ temp[N]_input Measured temperature. and temp5 reports the chip temperature. On LTC2977 and LTC2978, only one temperature measurement is supported and reports the chip temperature. - On LTC3880 and LTM4676, temp1 and temp2 report external - temperatures, and temp3 reports the chip temperature. + On LTC3880, LTC3882, and LTM4676, temp1 and temp2 + report external temperatures, and temp3 reports + the chip temperature. On LTC3883, temp1 reports an external temperature, and temp2 reports the chip temperature. temp[N]_min Mimimum temperature. LTC2974, LCT2977, and LTC2978 only.
@@ -128,7 +134,7 @@ power[N]_label "pout[1-4]". LTC2974: N=1-4 LTC2977: Not supported LTC2978: Not supported - LTC3880, LTM4676: N=1-2 + LTC3880, LTC3882, LTM4676: N=1-2 LTC3883: N=2 power[N]_input Measured output power.
@@ -143,7 +149,7 @@ curr[N]_label "iout[1-4]". LTC2974: N=1-4 LTC2977: not supported LTC2978: not supported - LTC3880, LTM4676: N=2-3 + LTC3880, LTC3882, LTM4676: N=2-3 LTC3883: N=2 curr[N]_input Measured output current. curr[N]_max Maximum output current.
drivers/hwmon/pmbus/ltc2978.c +44 -6
97 lines not on this page · raw message
Signature · 7 lines
2.1.4 _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors