Skip to contentSkip to conversation

ARM i.MX6: Add support for SabreSD board

RFC PATCH In review Hubert Feurstein 3 participants 4 messages Feb 5, 2013 – Feb 6, 2013

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

RFC PATCH 1/1 ARM i.MX6: Add support for SabreSD board

---
Ethernet is not working yet. I took over the initialisation from u-boot. Phy access seems to work, but I don't get any data out.
So some help is very appreciated ...

Best regards
Hubert

 arch/arm/Makefile                                  |   1 +
 arch/arm/boards/freescale-mx6-sabresd/Makefile     |   4 +
 arch/arm/boards/freescale-mx6-sabresd/board.c      | 271 +++++++++++++++++++++
 arch/arm/boards/freescale-mx6-sabresd/config.h     |   4 +
 .../freescale-mx6-sabresd/env/init/config-board    |   7 +
 .../boards/freescale-mx6-sabresd/flash_header.c    | 181 ++++++++++++++
 arch/arm/boards/freescale-mx6-sabresd/lowlevel.c   |  10 +
 arch/arm/configs/freescale-mx6-sabresd_defconfig   |  71 ++++++
 arch/arm/mach-imx/Kconfig                          |   5 +
 9 files changed, 554 insertions(+)
 create mode 100644 arch/arm/boards/freescale-mx6-sabresd/Makefile
 create mode 100644 arch/arm/boards/freescale-mx6-sabresd/board.c
 create mode 100644 arch/arm/boards/freescale-mx6-sabresd/config.h
 create mode 100644 arch/arm/boards/freescale-mx6-sabresd/env/init/config-board
 create mode 100644 arch/arm/boards/freescale-mx6-sabresd/flash_header.c
 create mode 100644 arch/arm/boards/freescale-mx6-sabresd/lowlevel.c
 create mode 100644 arch/arm/configs/freescale-mx6-sabresd_defconfig
arch/arm/Makefile +1 -0
index fcb2969..55290a9 100644
@@ -157,6 +157,7 @@ board-$(CONFIG_MACH_SABRELITE)			:= freescale-mx6-sabrelite
 board-$(CONFIG_MACH_TX53)			:= karo-tx53
 board-$(CONFIG_MACH_GUF_VINCELL)		:= guf-vincell
 board-$(CONFIG_MACH_EFIKA_MX_SMARTBOOK)		:= efika-mx-smartbook
+board-$(CONFIG_MACH_SABRESD)			:= freescale-mx6-sabresd
 
 machdirs := $(patsubst %,arch/arm/mach-%/,$(machine-y))
 
arch/arm/boards/freescale-mx6-sabresd/Makefile new file +4 -0
new file mode 100644
index 0000000..21fb7d9
@@ -0,0 +1,4 @@
+obj-y += board.o flash_header.o
+pbl-y += flash_header.o
+obj-y += lowlevel.o
+pbl-y += lowlevel.o
arch/arm/boards/freescale-mx6-sabresd/board.c new file +271 -0

271 lines not on this page · raw message

arch/arm/boards/freescale-mx6-sabresd/config.h new file +4 -0
new file mode 100644
index 0000000..ca15136
@@ -0,0 +1,4 @@
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#endif	/* __CONFIG_H */
arch/arm/boards/freescale-mx6-sabresd/env/init/config-board new file +7 -0
new file mode 100644
index 0000000..cf936fb
@@ -0,0 +1,7 @@
+#!/bin/sh
+
+# board defaults, do not change in running system. Change /env/config
+# instead
+
+global.hostname=SabreSD
+global.linux.bootargs.base="console=ttymxc0,115200"
arch/arm/boards/freescale-mx6-sabresd/flash_header.c new file +181 -0

181 lines not on this page · raw message

arch/arm/boards/freescale-mx6-sabresd/lowlevel.c new file +10 -0
new file mode 100644
index 0000000..8f995ee
@@ -0,0 +1,10 @@
+#include <common.h>
+#include <sizes.h>
+#include <asm/barebox-arm-head.h>
+#include <asm/barebox-arm.h>
+
+void __naked reset(void)
+{
+	common_reset();
+	barebox_arm_entry(0x10000000, SZ_1G, 0);
+}
arch/arm/configs/freescale-mx6-sabresd_defconfig new file +71 -0

71 lines not on this page · raw message

arch/arm/mach-imx/Kconfig +5 -0
index 4115d35..e3e0e73 100644
@@ -30,6 +30,7 @@ config ARCH_TEXT_BASE
 	default 0x8fe00000 if MACH_TX53
 	default 0x7fc00000 if MACH_GUF_VINCELL
 	default 0x97f00000 if MACH_EFIKA_MX_SMARTBOOK
+	default 0x17800000 if MACH_SABRESD
 
 config BOARDINFO
 	default "Eukrea CPUIMX25" if MACH_EUKREA_CPUIMX25
@@ -59,6 +60,7 @@ config BOARDINFO
 	default "Sabre Lite" if MACH_SABRELITE
 	default "Ka-Ro tx53" if MACH_TX53
 	default "Garz+Fricke Vincell" if MACH_GUF_VINCELL
+	default "SabreSD" if MACH_SABRESD
 
 choice
 	prompt "Select boot mode"
@@ -489,6 +491,9 @@ config MACH_MX6Q_ARM2
 config MACH_SABRELITE
 	bool "Freescale i.MX6 Sabre Lite"
 
+config MACH_SABRESD
+	bool "Freescale i.MX6 SabreSD"
+
 endchoice
 
 endif
Signature · 7 lines
1.8.1


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#1 lore raw

Hi Hubert!

Quoted 288 lines · Hubert Feurstein

---
Ethernet is not working yet. I took over the initialisation from u-boot. Phy access seems to work, but I don't get any data out.
So some help is very appreciated ...

Best regards
Hubert

 arch/arm/Makefile                                  |   1 +
 arch/arm/boards/freescale-mx6-sabresd/Makefile     |   4 +
 arch/arm/boards/freescale-mx6-sabresd/board.c      | 271 +++++++++++++++++++++
 arch/arm/boards/freescale-mx6-sabresd/config.h     |   4 +
 .../freescale-mx6-sabresd/env/init/config-board    |   7 +
 .../boards/freescale-mx6-sabresd/flash_header.c    | 181 ++++++++++++++
 arch/arm/boards/freescale-mx6-sabresd/lowlevel.c   |  10 +
 arch/arm/configs/freescale-mx6-sabresd_defconfig   |  71 ++++++
 arch/arm/mach-imx/Kconfig                          |   5 +
 9 files changed, 554 insertions(+)
 create mode 100644 arch/arm/boards/freescale-mx6-sabresd/Makefile
 create mode 100644 arch/arm/boards/freescale-mx6-sabresd/board.c
 create mode 100644 arch/arm/boards/freescale-mx6-sabresd/config.h
 create mode 100644 arch/arm/boards/freescale-mx6-sabresd/env/init/config-board
 create mode 100644 arch/arm/boards/freescale-mx6-sabresd/flash_header.c
 create mode 100644 arch/arm/boards/freescale-mx6-sabresd/lowlevel.c
 create mode 100644 arch/arm/configs/freescale-mx6-sabresd_defconfig
arch/arm/Makefile +1 -0
index fcb2969..55290a9 100644
@@ -157,6 +157,7 @@ board-$(CONFIG_MACH_SABRELITE)			:= freescale-mx6-sabrelite
 board-$(CONFIG_MACH_TX53)			:= karo-tx53
 board-$(CONFIG_MACH_GUF_VINCELL)		:= guf-vincell
 board-$(CONFIG_MACH_EFIKA_MX_SMARTBOOK)		:= efika-mx-smartbook
+board-$(CONFIG_MACH_SABRESD)			:= freescale-mx6-sabresd
 
 machdirs := $(patsubst %,arch/arm/mach-%/,$(machine-y))
 
arch/arm/boards/freescale-mx6-sabresd/Makefile new file +4 -0
new file mode 100644
index 0000000..21fb7d9
@@ -0,0 +1,4 @@
+obj-y += board.o flash_header.o
+pbl-y += flash_header.o
+obj-y += lowlevel.o
+pbl-y += lowlevel.o
arch/arm/boards/freescale-mx6-sabresd/board.c new file +233 -0
new file mode 100644
index 0000000..d341cf9
@@ -0,0 +1,271 @@
+/*
+ * Copyright (C) 2013 Hubert Feurstein <[email protected]>
+ *
+ * based on arch/arm/boards/freescale-mx6-sabrelite/board.c
+ * Copyright (C) 2012 Steffen Trumtrar, Pengutronix
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <init.h>
+#include <environment.h>
+#include <mach/imx6-regs.h>
+#include <fec.h>
+#include <mach/gpio.h>
+#include <asm/armlinux.h>
+#include <generated/mach-types.h>
+#include <partition.h>
+#include <linux/phy.h>
+#include <asm/io.h>
+#include <asm/mmu.h>
+#include <mach/generic.h>
+#include <sizes.h>
+#include <net.h>
+#include <mach/imx6.h>
+#include <mach/devices-imx6.h>
+#include <mach/iomux-mx6.h>
+#include <mach/gpio.h>
+#include <spi/spi.h>
+#include <mach/spi.h>
+#include <mach/usb.h>
+
+#define SABRESD_SD2_CD	IMX_GPIO_NR(2, 2)
+#define SABRESD_SD2_WP	IMX_GPIO_NR(2, 3)
+
+#define SABRESD_SD3_CD	IMX_GPIO_NR(2, 0)
+#define SABRESD_SD3_WP	IMX_GPIO_NR(2, 1)
+
+static iomux_v3_cfg_t sabresd_pads[] = {
+	/* UART1 */
+	MX6Q_PAD_CSI0_DAT11__UART1_RXD,
+	MX6Q_PAD_CSI0_DAT10__UART1_TXD,
+
+	/* SD2 */
+	MX6Q_PAD_SD2_CLK__USDHC2_CLK,
+	MX6Q_PAD_SD2_CMD__USDHC2_CMD,
+	MX6Q_PAD_SD2_DAT0__USDHC2_DAT0,
+	MX6Q_PAD_SD2_DAT1__USDHC2_DAT1,
+	MX6Q_PAD_SD2_DAT2__USDHC2_DAT2,
+	MX6Q_PAD_SD2_DAT3__USDHC2_DAT3,
+	MX6Q_PAD_NANDF_D4__USDHC2_DAT4,
+	MX6Q_PAD_NANDF_D5__USDHC2_DAT5,
+	MX6Q_PAD_NANDF_D6__USDHC2_DAT6,
+	MX6Q_PAD_NANDF_D7__USDHC2_DAT7,
+	MX6Q_PAD_NANDF_D2__GPIO_2_2,	/* CD */
+	MX6Q_PAD_NANDF_D3__GPIO_2_3,	/* WP */
+
+	/* SD3 */
+	MX6Q_PAD_SD3_CMD__USDHC3_CMD,
+	MX6Q_PAD_SD3_CLK__USDHC3_CLK,
+	MX6Q_PAD_SD3_DAT0__USDHC3_DAT0,
+	MX6Q_PAD_SD3_DAT1__USDHC3_DAT1,
+	MX6Q_PAD_SD3_DAT2__USDHC3_DAT2,
+	MX6Q_PAD_SD3_DAT3__USDHC3_DAT3,
+	MX6Q_PAD_SD3_DAT4__USDHC3_DAT4,
+	MX6Q_PAD_SD3_DAT5__USDHC3_DAT5,
+	MX6Q_PAD_SD3_DAT6__USDHC3_DAT6,
+	MX6Q_PAD_SD3_DAT7__USDHC3_DAT7,
+	MX6Q_PAD_NANDF_D0__GPIO_2_0,	/* CD */
+	MX6Q_PAD_NANDF_D1__GPIO_2_1,	/* WP */
+
+	/* SD4 */
+	MX6Q_PAD_SD4_CLK__USDHC4_CLK,
+	MX6Q_PAD_SD4_CMD__USDHC4_CMD,
+	MX6Q_PAD_SD4_DAT0__USDHC4_DAT0,
+	MX6Q_PAD_SD4_DAT1__USDHC4_DAT1,
+	MX6Q_PAD_SD4_DAT2__USDHC4_DAT2,
+	MX6Q_PAD_SD4_DAT3__USDHC4_DAT3,
+	MX6Q_PAD_SD4_DAT4__USDHC4_DAT4,
+	MX6Q_PAD_SD4_DAT5__USDHC4_DAT5,
+	MX6Q_PAD_SD4_DAT6__USDHC4_DAT6,
+	MX6Q_PAD_SD4_DAT7__USDHC4_DAT7,
+
+	/* ECSPI1 */
+	MX6Q_PAD_KEY_COL0__ECSPI1_SCLK,
+	MX6Q_PAD_KEY_ROW0__ECSPI1_MOSI,
+	MX6Q_PAD_KEY_COL1__ECSPI1_MISO,
+	MX6Q_PAD_KEY_ROW1__GPIO_4_9,	/* CS0 */
+
+	/* I2C0 */
+	MX6Q_PAD_CSI0_DAT8__I2C1_SDA,
+	MX6Q_PAD_CSI0_DAT9__I2C1_SCL,
+
+	/* I2C1 */
+	MX6Q_PAD_KEY_COL3__I2C2_SCL,
+	MX6Q_PAD_KEY_ROW3__I2C2_SDA,
+
+	/* I2C2 */
+	MX6Q_PAD_GPIO_3__I2C3_SCL,
+	MX6Q_PAD_GPIO_6__I2C3_SDA,
+};
+
+static iomux_v3_cfg_t sabresd_enet_pads[] = {
+	/* Ethernet */
+	MX6Q_PAD_ENET_MDC__ENET_MDC,
+	MX6Q_PAD_ENET_MDIO__ENET_MDIO,
+	MX6Q_PAD_ENET_REF_CLK__ENET_TX_CLK,
+
+	MX6Q_PAD_RGMII_TXC__ENET_RGMII_TXC,
+	MX6Q_PAD_RGMII_TD0__ENET_RGMII_TD0,
+	MX6Q_PAD_RGMII_TD1__ENET_RGMII_TD1,
+	MX6Q_PAD_RGMII_TD2__ENET_RGMII_TD2,
+	MX6Q_PAD_RGMII_TD3__ENET_RGMII_TD3,
+
+	MX6Q_PAD_RGMII_TX_CTL__ENET_RGMII_TX_CTL,
+	MX6Q_PAD_RGMII_RXC__ENET_RGMII_RXC,
+	MX6Q_PAD_RGMII_RD0__ENET_RGMII_RD0,
+	MX6Q_PAD_RGMII_RD1__ENET_RGMII_RD1,
+	MX6Q_PAD_RGMII_RD2__ENET_RGMII_RD2,
+	MX6Q_PAD_RGMII_RD3__ENET_RGMII_RD3,
+	MX6Q_PAD_RGMII_RX_CTL__ENET_RGMII_RX_CTL,
+
+	/* AR8031 PHY Reset */
+	MX6Q_PAD_ENET_CRS_DV__GPIO_1_25,
+};
+
+static int sabresd_mem_init(void)
+{
+	arm_add_mem_device("ram0", 0x10000000, SZ_1G);
+
+	return 0;
+}
+mem_initcall(sabresd_mem_init);
+
+static void mx6_rgmii_rework(struct phy_device *dev)
+{
+	u16 val;
+
+	/* To enable AR8031 ouput a 125MHz clk from CLK_25M */
+	phy_write(dev, 0xd, 0x7);
+	phy_write(dev, 0xe, 0x8016);
+	phy_write(dev, 0xd, 0x4007);
+
+	val = phy_read(dev, 0xe);
+	val &= 0xffe3;
+	val |= 0x18;
+	phy_write(dev, 0xe, val);
+
+	/* introduce tx clock delay */
+	phy_write(dev, 0x1d, 0x5);
+	val = phy_read(dev, 0x1e);
+	val |= 0x0100;
+	phy_write(dev, 0x1e, val);
+}
+
+static struct fec_platform_data fec_info = {
+	.xcv_type = RGMII,
+	.phy_init = mx6_rgmii_rework,
+	.phy_addr = 1,
+};
+
+static int sabresd_enet_setup(void)
+{
+	mxc_iomux_v3_setup_multiple_pads(sabresd_enet_pads, ARRAY_SIZE(sabresd_enet_pads));
+
+	/* Reset AR8031 PHY */
+	gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
+	udelay(500);
+	gpio_set_value(IMX_GPIO_NR(1, 25), 1);
+
+	return 0;
+}
+
+static inline int imx6_iim_register_fec_ethaddr(void)
+{
+	u32 value;
+	u8 buf[6];
+
+	value = readl(MX6_OCOTP_BASE_ADDR + 0x630);
+	buf[0] = (value >> 8);
+	buf[1] = value;
+
+	value = readl(MX6_OCOTP_BASE_ADDR + 0x620);
+	buf[2] = value >> 24;
+	buf[3] = value >> 16;
+	buf[4] = value >> 8;
+	buf[5] = value;
+
+	eth_register_ethaddr(0, buf);
+
+	return 0;
+}
+
+static int sabresd_spi_cs[] = {IMX_GPIO_NR(4, 9)};
+
+static struct spi_imx_master sabresd_spi_0_data = {
+	.chipselect = sabresd_spi_cs,
+	.num_chipselect = ARRAY_SIZE(sabresd_spi_cs),
+};
+
+static const struct spi_board_info sabresd_spi_board_info[] = {
+	{
+		.name = "m25p80",
+		.max_speed_hz = 40000000,
+		.bus_num = 0,
+		.chip_select = 0,
+	}
+};
+
+static struct esdhc_platform_data sabresd_sd2_data = {
+	.cd_gpio = SABRESD_SD2_CD,
+	.cd_type = ESDHC_CD_GPIO,
+	.wp_gpio = SABRESD_SD2_WP,
+	.wp_type = ESDHC_WP_GPIO,
+};
+
+static struct esdhc_platform_data sabresd_sd3_data = {
+	.cd_gpio = SABRESD_SD3_CD,
+	.cd_type = ESDHC_CD_GPIO,
+	.wp_gpio = SABRESD_SD3_WP,
+	.wp_type = ESDHC_WP_GPIO,
+};
+
+static struct esdhc_platform_data sabresd_sd4_data = {
+	.cd_type = ESDHC_CD_PERMANENT,

arch/arm/boards/freescale-mx6-sabresd/board.c line 243

Quoted 10 lines
arch/arm/boards/freescale-mx6-sabresd/board.c new file +10 -0
+	.wp_type = ESDHC_WP_CONTROLLER,
+};
+
+static int sabresd_devices_init(void)
+{
+	imx6_add_mmc1(&sabresd_sd2_data);
+	imx6_add_mmc2(&sabresd_sd3_data);
+	imx6_add_mmc3(&sabresd_sd4_data);
+
+	sabresd_enet_setup();

I think this is not necessary. The SabreSD ethernet works without this and you can merge the two pinmuxings. On the SabreLite this was necessary because of remuxing.
The rest of the ethernet looks okay though and should work. I have a v2012.08.0 barebox for the SabreSD that only does ethernet (Forgot to mainline the patches :-( ). The pinctrl and the rest is almost the same. The only difference is the rgmii_rework.
I have

	imx6_add_fec(&fec_info);
        mx6_rgmii_rework();

And I use mii_device to do the rgmii_rework. I haven't followed the changes in the phy-driver since 2012.08.0, so I don't know if that makes any difference in the setup of the fec.

Quoted 57 lines
arch/arm/boards/freescale-mx6-sabresd/board.c new file +28 -0
+	imx6_iim_register_fec_ethaddr();
+	imx6_add_fec(&fec_info);
+
+	spi_register_board_info(sabresd_spi_board_info,
+			ARRAY_SIZE(sabresd_spi_board_info));
+	imx6_add_spi0(&sabresd_spi_0_data);
+
+	armlinux_set_bootparams((void *)0x10000100);
+	armlinux_set_architecture(3980);
+
+	devfs_add_partition("m25p0", 0, SZ_512K, DEVFS_PARTITION_FIXED, "self0");
+	devfs_add_partition("m25p0", SZ_512K, SZ_512K, DEVFS_PARTITION_FIXED, "env0");
+
+	return 0;
+}
+device_initcall(sabresd_devices_init);
+
+static int sabresd_console_init(void)
+{
+	mxc_iomux_v3_setup_multiple_pads(sabresd_pads, ARRAY_SIZE(sabresd_pads));
+
+	imx6_init_lowlevel();
+
+	imx6_add_uart0();
+
+	return 0;
+}
+console_initcall(sabresd_console_init);
arch/arm/boards/freescale-mx6-sabresd/config.h new file +4 -0
new file mode 100644
index 0000000..ca15136
@@ -0,0 +1,4 @@
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#endif	/* __CONFIG_H */
arch/arm/boards/freescale-mx6-sabresd/env/init/config-board new file +7 -0
new file mode 100644
index 0000000..cf936fb
@@ -0,0 +1,7 @@
+#!/bin/sh
+
+# board defaults, do not change in running system. Change /env/config
+# instead
+
+global.hostname=SabreSD
+global.linux.bootargs.base="console=ttymxc0,115200"
arch/arm/boards/freescale-mx6-sabresd/flash_header.c new file +0 -0
new file mode 100644
index 0000000..0c32bdc

arch/arm/boards/freescale-mx6-sabresd/flash_header.c line 5

Quoted 5 lines
arch/arm/boards/freescale-mx6-sabresd/flash_header.c new file +5 -0
@@ -0,0 +1,181 @@
+/*
+ * Copyright (C) 2013 Hubert Feurstein <[email protected]>
+ *
+ * based on arch/arm/boards/freescale-mx6-sabrelite/flash_header.c
+ * Copyright (C) 2011 Marc Kleine-Budde <[email protected]>

If I see this right, it is not _based_ on freescale-mx6-sabrelite/flash_header.c, but is the SAME file and therefore the same as freescale-mx6-arm2/flash_header.c

Quoted 290 lines
arch/arm/boards/freescale-mx6-sabresd/flash_header.c new file +176 -0
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <common.h>
+#include <asm/byteorder.h>
+#include <mach/imx-flash-header.h>
+#include <mach/imx6-regs.h>
+#include <asm/barebox-arm-head.h>
+
+void __naked __flash_header_start go(void)
+{
+	barebox_arm_head();
+}
+
+#define DCD(a, v) { .addr = cpu_to_be32(a), .val = cpu_to_be32(v), }
+
+struct imx_dcd_v2_entry __dcd_entry_section dcd_entry[] = {
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x5a8, 0x00000030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x5b0, 0x00000030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x524, 0x00000030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x51c, 0x00000030),
+
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x518, 0x00000030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x50c, 0x00000030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x5b8, 0x00000030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x5c0, 0x00000030),
+
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x5ac, 0x00020030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x5b4, 0x00020030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x528, 0x00020030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x520, 0x00020030),
+
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x514, 0x00020030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x510, 0x00020030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x5bc, 0x00020030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x5c4, 0x00020030),
+
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x56c, 0x00020030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x578, 0x00020030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x588, 0x00020030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x594, 0x00020030),
+
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x57c, 0x00020030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x590, 0x00003000),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x598, 0x00003000),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x58c, 0x00000000),
+
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x59c, 0x00003030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x5a0, 0x00003030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x784, 0x00000030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x788, 0x00000030),
+
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x794, 0x00000030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x79c, 0x00000030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x7a0, 0x00000030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x7a4, 0x00000030),
+
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x7a8, 0x00000030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x748, 0x00000030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x74c, 0x00000030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x750, 0x00020000),
+
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x758, 0x00000000),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x774, 0x00020000),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x78c, 0x00000030),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x798, 0x000C0000),
+
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x81c, 0x33333333),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x820, 0x33333333),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x824, 0x33333333),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x828, 0x33333333),
+
+	DCD(MX6_MMDC_P1_BASE_ADDR + 0x81c, 0x33333333),
+	DCD(MX6_MMDC_P1_BASE_ADDR + 0x820, 0x33333333),
+	DCD(MX6_MMDC_P1_BASE_ADDR + 0x824, 0x33333333),
+	DCD(MX6_MMDC_P1_BASE_ADDR + 0x828, 0x33333333),
+
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x018, 0x00081740),
+
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x01c, 0x00008000),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x00c, 0x555A7975),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x010, 0xFF538E64),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x014, 0x01FF00DB),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x02c, 0x000026D2),
+
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x030, 0x005B0E21),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x008, 0x09444040),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x004, 0x00025576),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x040, 0x00000027),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x000, 0x831A0000),
+
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x01c, 0x04088032),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x01c, 0x0408803A),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x01c, 0x00008033),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x01c, 0x0000803B),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x01c, 0x00428031),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x01c, 0x00428039),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x01c, 0x09408030),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x01c, 0x09408038),
+
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x01c, 0x04008040),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x01c, 0x04008048),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x800, 0xA1380003),
+	DCD(MX6_MMDC_P1_BASE_ADDR + 0x800, 0xA1380003),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x020, 0x00005800),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x818, 0x00022227),
+	DCD(MX6_MMDC_P1_BASE_ADDR + 0x818, 0x00022227),
+
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x83c, 0x434B0350),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x840, 0x034C0359),
+	DCD(MX6_MMDC_P1_BASE_ADDR + 0x83c, 0x434B0350),
+	DCD(MX6_MMDC_P1_BASE_ADDR + 0x840, 0x03650348),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x848, 0x4436383B),
+	DCD(MX6_MMDC_P1_BASE_ADDR + 0x848, 0x39393341),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x850, 0x35373933),
+	DCD(MX6_MMDC_P1_BASE_ADDR + 0x850, 0x48254A36),
+
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x80c, 0x001F001F),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x810, 0x001F001F),
+
+	DCD(MX6_MMDC_P1_BASE_ADDR + 0x80c, 0x00440044),
+	DCD(MX6_MMDC_P1_BASE_ADDR + 0x810, 0x00440044),
+
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x8b8, 0x00000800),
+	DCD(MX6_MMDC_P1_BASE_ADDR + 0x8b8, 0x00000800),
+
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x01c, 0x00000000),
+	DCD(MX6_MMDC_P0_BASE_ADDR + 0x404, 0x00011006),
+
+	DCD(MX6_CCM_BASE_ADDR + 0x068, 0x00c03f3f),
+	DCD(MX6_CCM_BASE_ADDR + 0x06c, 0x0030fc03),
+	DCD(MX6_CCM_BASE_ADDR + 0x070, 0x0fffc000),
+	DCD(MX6_CCM_BASE_ADDR + 0x074, 0x3ff00000),
+	DCD(MX6_CCM_BASE_ADDR + 0x078, 0x00fff300),
+	DCD(MX6_CCM_BASE_ADDR + 0x07c, 0x0f0000c3),
+	DCD(MX6_CCM_BASE_ADDR + 0x080, 0x000003ff),
+
+	/* enable AXI cache for VDOA/VPU/IPU */
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x010, 0xf00000cf),
+	/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x018, 0x007f007f),
+	DCD(MX6_IOMUXC_BASE_ADDR + 0x01c, 0x007f007f),
+};
+
+#define APP_DEST	CONFIG_TEXT_BASE
+
+struct imx_flash_header_v2 __flash_header_section flash_header = {
+	.header.tag		= IVT_HEADER_TAG,
+	.header.length		= cpu_to_be16(32),
+	.header.version		= IVT_VERSION,
+	.entry			= (u32)_stext,
+	.dcd_ptr		= APP_DEST + FLASH_HEADER_OFFSET + offsetof(struct imx_flash_header_v2, dcd),
+	.boot_data_ptr		= APP_DEST + FLASH_HEADER_OFFSET + offsetof(struct imx_flash_header_v2, boot_data),
+	.self			= APP_DEST + FLASH_HEADER_OFFSET,
+
+	.boot_data.start	= APP_DEST,
+	.boot_data.size		= barebox_image_size,
+
+	.dcd.header.tag		= DCD_HEADER_TAG,
+	.dcd.header.length	= cpu_to_be16(sizeof(struct imx_dcd) + sizeof(dcd_entry)),
+	.dcd.header.version	= DCD_VERSION,
+
+	.dcd.command.tag	= DCD_COMMAND_WRITE_TAG,
+	.dcd.command.length	= cpu_to_be16(sizeof(struct imx_dcd_command) + sizeof(dcd_entry)),
+	.dcd.command.param	= DCD_COMMAND_WRITE_PARAM,
+};
arch/arm/boards/freescale-mx6-sabresd/lowlevel.c new file +10 -0
new file mode 100644
index 0000000..8f995ee
@@ -0,0 +1,10 @@
+#include <common.h>
+#include <sizes.h>
+#include <asm/barebox-arm-head.h>
+#include <asm/barebox-arm.h>
+
+void __naked reset(void)
+{
+	common_reset();
+	barebox_arm_entry(0x10000000, SZ_1G, 0);
+}
arch/arm/configs/freescale-mx6-sabresd_defconfig new file +71 -0
new file mode 100644
index 0000000..a2a7dcc
@@ -0,0 +1,71 @@
+CONFIG_ARCH_IMX=y
+CONFIG_ARCH_IMX6=y
+CONFIG_MACH_SABRESD=y
+CONFIG_IMX_IIM=y
+CONFIG_IMX_IIM_FUSE_BLOW=y
+CONFIG_THUMB2_BAREBOX=y
+CONFIG_CMD_ARM_MMUINFO=y
+CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
+CONFIG_ARM_UNWIND=y
+CONFIG_MMU=y
+CONFIG_MALLOC_SIZE=0x4000000
+CONFIG_MALLOC_TLSF=y
+CONFIG_KALLSYMS=y
+CONFIG_LONGHELP=y
+CONFIG_HUSH_FANCY_PROMPT=y
+CONFIG_CMDLINE_EDITING=y
+CONFIG_AUTO_COMPLETE=y
+CONFIG_MENU=y
+CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y
+CONFIG_DEFAULT_ENVIRONMENT_PATH="arch/arm/boards/freescale-mx6-sabresd/env"
+CONFIG_CMD_EDIT=y
+CONFIG_CMD_SLEEP=y
+CONFIG_CMD_MSLEEP=y
+CONFIG_CMD_SAVEENV=y
+CONFIG_CMD_EXPORT=y
+CONFIG_CMD_READLINE=y
+CONFIG_CMD_MENU=y
+CONFIG_CMD_MENU_MANAGEMENT=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_DIRNAME=y
+CONFIG_CMD_TFTP=y
+CONFIG_CMD_ECHO_E=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_IOMEM=y
+CONFIG_CMD_CRC=y
+CONFIG_CMD_CRC_CMP=y
+CONFIG_CMD_MD5SUM=y
+CONFIG_CMD_FLASH=y
+CONFIG_CMD_BOOTM_SHOW_TYPE=y
+CONFIG_CMD_BOOTM_VERBOSE=y
+CONFIG_CMD_BOOTM_INITRD=y
+CONFIG_CMD_BOOTM_OFTREE=y
+CONFIG_CMD_BOOTM_OFTREE_UIMAGE=y
+CONFIG_CMD_BOOTM_AIMAGE=y
+# CONFIG_CMD_BOOTU is not set
+CONFIG_CMD_RESET=y
+CONFIG_CMD_GO=y
+CONFIG_CMD_TIMEOUT=y
+CONFIG_CMD_PARTITION=y
+CONFIG_CMD_MAGICVAR=y
+CONFIG_CMD_MAGICVAR_HELP=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_UNCOMPRESS=y
+CONFIG_NET=y
+CONFIG_NET_DHCP=y
+CONFIG_NET_PING=y
+CONFIG_NET_NETCONSOLE=y
+CONFIG_NET_RESOLV=y
+CONFIG_DRIVER_NET_FEC_IMX=y
+CONFIG_DRIVER_SPI_IMX=y
+CONFIG_MTD=y
+CONFIG_MTD_M25P80=y
+CONFIG_MTD_SST25L=y
+CONFIG_MCI=y
+CONFIG_MCI_STARTUP=y
+CONFIG_MCI_IMX_ESDHC=y
+CONFIG_FS_TFTP=y
+CONFIG_FS_NFS=y
+CONFIG_FS_FAT=y
+CONFIG_FS_FAT_LFN=y
+CONFIG_LZO_DECOMPRESS=y
arch/arm/mach-imx/Kconfig +2 -0
index 4115d35..e3e0e73 100644
@@ -30,6 +30,7 @@ config ARCH_TEXT_BASE
 	default 0x8fe00000 if MACH_TX53
 	default 0x7fc00000 if MACH_GUF_VINCELL
 	default 0x97f00000 if MACH_EFIKA_MX_SMARTBOOK
+	default 0x17800000 if MACH_SABRESD
 
 config BOARDINFO
 	default "Eukrea CPUIMX25" if MACH_EUKREA_CPUIMX25
@@ -59,6 +60,7 @@ config BOARDINFO
 	default "Sabre Lite" if MACH_SABRELITE
 	default "Ka-Ro tx53" if MACH_TX53
 	default "Garz+Fricke Vincell" if MACH_GUF_VINCELL
+	default "SabreSD" if MACH_SABRESD
 
 choice
 	prompt "Select boot mode"

arch/arm/mach-imx/Kconfig config MACH_MX6Q_ARM2 · line 499

Quoted 9 lines
arch/arm/mach-imx/Kconfig +3 -0
@@ -489,6 +491,9 @@ config MACH_MX6Q_ARM2
 config MACH_SABRELITE
 	bool "Freescale i.MX6 Sabre Lite"
 
+config MACH_SABRESD
+	bool "Freescale i.MX6 SabreSD"
+
 endchoice
 
 endif

Regards,
Steffen

Signature · 9 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#2 lore raw

Hi Steffen,

2013/2/5 Steffen Trumtrar <[email protected]>:

Quoted 11 lines

arch/arm/boards/freescale-mx6-sabresd/board.c line 243

Quoted 7 lines
arch/arm/boards/freescale-mx6-sabresd/board.c new file +7 -0
+static int sabresd_devices_init(void)
+{
+     imx6_add_mmc1(&sabresd_sd2_data);
+     imx6_add_mmc2(&sabresd_sd3_data);
+     imx6_add_mmc3(&sabresd_sd4_data);
+
+     sabresd_enet_setup();

I think this is not necessary. The SabreSD ethernet works without this and you can merge the two pinmuxings. On the SabreLite this was necessary because of remuxing.

OK

Quoted 7 lines

The rest of the ethernet looks okay though and should work. I have a v2012.08.0 barebox for the SabreSD that only does ethernet (Forgot to mainline the patches :-( ). The pinctrl and the rest is almost the same. The only difference is the rgmii_rework.
I have

        imx6_add_fec(&fec_info);
        mx6_rgmii_rework();

I recognized, that my rework code is the same as for the Arm2-board. But ethernet is still not working yet.
Btw, what are your clock settings? I'm also a little bit confused about that fec_imx.c requests
the 'ipg' clock (is this the correct one, btw? shouldn't it be 'enet_ref' ?), but then the clock
is not enabled. Looks like a bug. But even with enabled clocks it does not work ...

Here's the boot log:

barebox 2013.01.0-00346-g8aa2579-dirty #112 Wed Feb 6 16:23:37 CET 2013
Board: SabreSD
[...]
fec clock ipg
mdio_bus: miibus0: probed
fec probed
eth0: got preset MAC address: 00:04:9F:02:6F:1C
malloc space: 0x13800000 -> 0x177fffff (size 64 MiB)
stack space: 0x137f8000 -> 0x137fffff (size 32 KiB)
Open /dev/env0 No such file or directory
no valid environment found on /dev/env0. Using default environment running /env/bin/init...

Hit m for menu or any other key to stop autoboot: 3

type exit to get to the menu
barebox@SabreSD:/
barebox@SabreSD:/ dhcp
1000Mbps full duplex link detected
T T T T T T T T T T T T T T T T T T T T dhcp failed: Connection timed out
dhcp: Connection timed out
barebox@SabreSD:/

[...]

Quoted 3 lines

If I see this right, it is not _based_ on freescale-mx6-sabrelite/flash_header.c, but is the SAME file and therefore the same as freescale-mx6-arm2/flash_header.c

In fact it is the same file as for SabreLite, the Arm2 is slightly different. But maybe they
can be consolidated.

[...]

Regards,
Hubert

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox

maintainer
#3 lore raw
Quoted 23 lines · Hubert Feurstein

Hi Steffen,

2013/2/5 Steffen Trumtrar <[email protected]>:

Quoted 11 lines

arch/arm/boards/freescale-mx6-sabresd/board.c line 243

Quoted 7 lines
arch/arm/boards/freescale-mx6-sabresd/board.c new file +7 -0
+static int sabresd_devices_init(void)
+{
+     imx6_add_mmc1(&sabresd_sd2_data);
+     imx6_add_mmc2(&sabresd_sd3_data);
+     imx6_add_mmc3(&sabresd_sd4_data);
+
+     sabresd_enet_setup();

I think this is not necessary. The SabreSD ethernet works without this and you can merge the two pinmuxings. On the SabreLite this was necessary because of remuxing.

OK

Quoted 7 lines

The rest of the ethernet looks okay though and should work. I have a v2012.08.0 barebox for the SabreSD that only does ethernet (Forgot to mainline the patches :-( ). The pinctrl and the rest is almost the same. The only difference is the rgmii_rework.
I have

        imx6_add_fec(&fec_info);
        mx6_rgmii_rework();
Quoted 2 lines

I recognized, that my rework code is the same as for the Arm2-board. But ethernet is still not working yet.

The phy rework code is phy specific. You have to look at the phy datasheet to guess the correct values (Or look at the FSL sourcecode)

Quoted 6 lines

Hit m for menu or any other key to stop autoboot: 3

type exit to get to the menu
barebox@SabreSD:/
barebox@SabreSD:/ dhcp
1000Mbps full duplex link detected

I have never tested gigabit support under barebox. Maybe connect to a 100MBit switch for now?

Sascha

Signature · 9 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox