Skip to contentSkip to conversation

nand: mxc: Prepare to add support for i.MX5

PATCH Superseded Benoît Thébaudeau 2 participants 5 messages Feb 5, 2013 – Feb 6, 2013

Subsystems (5)

v3 of 7 Superseded Latest is v7 →

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/4 nand: mxc: Prepare to add support for i.MX5

Add some abstraction to NFC defitnitions so that some parts of the current code can also be used for future i.MX5 code.

Clean up a few things by the way.

---
Changes in v3:
- Separate code reformatting from behavioral changes.

Changes in v2:
- Fix warning for unused tmp variable in board_nand_init() for NFC V1.

 drivers/mtd/nand/mxc_nand.c  |   92 +++++++++++++++++++++---------------------
 include/fsl_nfc.h            |   72 ++++++++++++---------------------
 nand_spl/nand_boot_fsl_nfc.c |   47 +++++++++++----------
 3 files changed, 97 insertions(+), 114 deletions(-)
drivers/mtd/nand/mxc_nand.c +46 -46
index d0ded48..045df49 100644
@@ -150,7 +150,7 @@ static uint32_t *mxc_nand_memcpy32(uint32_t *dest, uint32_t *source, size_t size
 
 /*
  * This function polls the NANDFC to wait for the basic operation to
- * complete by checking the INT bit of config2 register.
+ * complete by checking the INT bit.
  */
 static void wait_op_done(struct mxc_nand_host *host, int max_retries,
 				uint16_t param)
@@ -158,10 +158,10 @@ static void wait_op_done(struct mxc_nand_host *host, int max_retries,
 	uint32_t tmp;
 
 	while (max_retries-- > 0) {
-		if (readw(&host->regs->config2) & NFC_INT) {
-			tmp = readw(&host->regs->config2);
-			tmp  &= ~NFC_INT;
-			writew(tmp, &host->regs->config2);
+		tmp = readnfc(&host->regs->config2);
+		if (tmp & NFC_V1_V2_CONFIG2_INT) {
+			tmp &= ~NFC_V1_V2_CONFIG2_INT;
+			writenfc(tmp, &host->regs->config2);
 			break;
 		}
 		udelay(1);
@@ -180,8 +180,8 @@ static void send_cmd(struct mxc_nand_host *host, uint16_t cmd)
 {
 	MTDDEBUG(MTD_DEBUG_LEVEL3, "send_cmd(host, 0x%x)\n", cmd);
 
-	writew(cmd, &host->regs->flash_cmd);
-	writew(NFC_CMD, &host->regs->config2);
+	writenfc(cmd, &host->regs->flash_cmd);
+	writenfc(NFC_CMD, &host->regs->operation);
 
 	/* Wait for operation to complete */
 	wait_op_done(host, TROP_US_DELAY, cmd);
@@ -196,8 +196,8 @@ static void send_addr(struct mxc_nand_host *host, uint16_t addr)
 {
 	MTDDEBUG(MTD_DEBUG_LEVEL3, "send_addr(host, 0x%x)\n", addr);
 
-	writew(addr, &host->regs->flash_addr);
-	writew(NFC_ADDR, &host->regs->config2);
+	writenfc(addr, &host->regs->flash_addr);
+	writenfc(NFC_ADDR, &host->regs->operation);
 
 	/* Wait for operation to complete */
 	wait_op_done(host, TROP_US_DELAY, addr);
@@ -229,19 +229,19 @@ static void send_prog_page(struct mxc_nand_host *host, uint8_t buf_id,
 		}
 	}
 
-	writew(buf_id, &host->regs->buf_addr);
+	writenfc(buf_id, &host->regs->buf_addr);
 
 	/* Configure spare or page+spare access */
 	if (!host->pagesize_2k) {
-		uint16_t config1 = readw(&host->regs->config1);
+		uint16_t config1 = readnfc(&host->regs->config1);
 		if (spare_only)
-			config1 |= NFC_SP_EN;
+			config1 |= NFC_CONFIG1_SP_EN;
 		else
-			config1 &= ~NFC_SP_EN;
-		writew(config1, &host->regs->config1);
+			config1 &= ~NFC_CONFIG1_SP_EN;
+		writenfc(config1, &host->regs->config1);
 	}
 
-	writew(NFC_INPUT, &host->regs->config2);
+	writenfc(NFC_INPUT, &host->regs->operation);
 
 	/* Wait for operation to complete */
 	wait_op_done(host, TROP_US_DELAY, spare_only);
@@ -256,19 +256,19 @@ static void send_read_page(struct mxc_nand_host *host, uint8_t buf_id,
 {
 	MTDDEBUG(MTD_DEBUG_LEVEL3, "send_read_page (%d)\n", spare_only);
 
-	writew(buf_id, &host->regs->buf_addr);
+	writenfc(buf_id, &host->regs->buf_addr);
 
 	/* Configure spare or page+spare access */
 	if (!host->pagesize_2k) {
-		uint32_t config1 = readw(&host->regs->config1);
+		uint32_t config1 = readnfc(&host->regs->config1);
 		if (spare_only)
-			config1 |= NFC_SP_EN;
+			config1 |= NFC_CONFIG1_SP_EN;
 		else
-			config1 &= ~NFC_SP_EN;
-		writew(config1, &host->regs->config1);
+			config1 &= ~NFC_CONFIG1_SP_EN;
+		writenfc(config1, &host->regs->config1);
 	}
 
-	writew(NFC_OUTPUT, &host->regs->config2);
+	writenfc(NFC_OUTPUT, &host->regs->operation);
 
 	/* Wait for operation to complete */
 	wait_op_done(host, TROP_US_DELAY, spare_only);
@@ -296,14 +296,14 @@ static void send_read_id(struct mxc_nand_host *host)
 	uint16_t tmp;
 
 	/* NANDFC buffer 0 is used for device ID output */
-	writew(0x0, &host->regs->buf_addr);
+	writenfc(0x0, &host->regs->buf_addr);
 
 	/* Read ID into main buffer */
-	tmp = readw(&host->regs->config1);
-	tmp &= ~NFC_SP_EN;
-	writew(tmp, &host->regs->config1);
+	tmp = readnfc(&host->regs->config1);
+	tmp &= ~NFC_CONFIG1_SP_EN;
+	writenfc(tmp, &host->regs->config1);
 
-	writew(NFC_ID, &host->regs->config2);
+	writenfc(NFC_ID, &host->regs->operation);
 
 	/* Wait for operation to complete */
 	wait_op_done(host, TROP_US_DELAY, 0);
@@ -323,14 +323,14 @@ static uint16_t get_dev_status(struct mxc_nand_host *host)
 	/* store the main area1 first word, later do recovery */
 	store = readl(main_buf);
 	/* NANDFC buffer 1 is used for device status */
-	writew(1, &host->regs->buf_addr);
+	writenfc(1, &host->regs->buf_addr);
 
 	/* Read status into main buffer */
-	tmp = readw(&host->regs->config1);
-	tmp &= ~NFC_SP_EN;
-	writew(tmp, &host->regs->config1);
+	tmp = readnfc(&host->regs->config1);
+	tmp &= ~NFC_CONFIG1_SP_EN;
+	writenfc(tmp, &host->regs->config1);
 
-	writew(NFC_STATUS, &host->regs->config2);
+	writenfc(NFC_STATUS, &host->regs->operation);
 
 	/* Wait for operation to complete */
 	wait_op_done(host, TROP_US_DELAY, 0);
@@ -359,13 +359,13 @@ static void _mxc_nand_enable_hwecc(struct mtd_info *mtd, int on)
 {
 	struct nand_chip *nand_chip = mtd->priv;
 	struct mxc_nand_host *host = nand_chip->priv;
-	uint16_t tmp = readw(&host->regs->config1);
+	uint16_t tmp = readnfc(&host->regs->config1);
 
 	if (on)
-		tmp |= NFC_ECC_EN;
+		tmp |= NFC_V1_V2_CONFIG1_ECC_EN;
 	else
-		tmp &= ~NFC_ECC_EN;
-	writew(tmp, &host->regs->config1);
+		tmp &= ~NFC_V1_V2_CONFIG1_ECC_EN;
+	writenfc(tmp, &host->regs->config1);
 }
 
 #ifdef CONFIG_MXC_NAND_HWECC
@@ -698,7 +698,7 @@ static int mxc_nand_correct_data(struct mtd_info *mtd, u_char *dat,
 	 * additional correction.  2-Bit errors cannot be corrected by
 	 * HW ECC, so we need to return failure
 	 */
-	uint16_t ecc_status = readw(&host->regs->ecc_status_result);
+	uint16_t ecc_status = readnfc(&host->regs->ecc_status_result);
 
 	if (((ecc_status & 0x3) == 2) || ((ecc_status >> 2) == 2)) {
 		MTDDEBUG(MTD_DEBUG_LEVEL0,
@@ -1241,24 +1241,24 @@ int board_nand_init(struct nand_chip *this)
 #endif
 
 #ifdef MXC_NFC_V2_1
-	tmp = readw(&host->regs->config1);
-	tmp |= NFC_ONE_CYCLE;
-	tmp |= NFC_4_8N_ECC;
-	writew(tmp, &host->regs->config1);
+	tmp = readnfc(&host->regs->config1);
+	tmp |= NFC_V2_CONFIG1_ONE_CYCLE;
+	tmp |= NFC_V2_CONFIG1_ECC_MODE_4;
+	writenfc(tmp, &host->regs->config1);
 	if (host->pagesize_2k)
-		writew(64/2, &host->regs->spare_area_size);
+		writenfc(64/2, &host->regs->spare_area_size);
 	else
-		writew(16/2, &host->regs->spare_area_size);
+		writenfc(16/2, &host->regs->spare_area_size);
 #endif
 
 	/*
 	 * preset operation
 	 * Unlock the internal RAM Buffer
 	 */
-	writew(0x2, &host->regs->config);
+	writenfc(0x2, &host->regs->config);
 
 	/* Blocks to be unlocked */
-	writew(0x0, &host->regs->unlockstart_blkaddr);
+	writenfc(0x0, &host->regs->unlockstart_blkaddr);
 	/* Originally (Freescale LTIB 2.6.21) 0x4000 was written to the
 	 * unlockend_blkaddr, but the magic 0x4000 does not always work
 	 * when writing more than some 32 megabytes (on 2k page nands)
@@ -1270,10 +1270,10 @@ int board_nand_init(struct nand_chip *this)
 	 * This might be NAND chip specific and the i.MX31 datasheet is
 	 * extremely vague about the semantics of this register.
 	 */
-	writew(0xFFFF, &host->regs->unlockend_blkaddr);
+	writenfc(0xFFFF, &host->regs->unlockend_blkaddr);
 
 	/* Unlock Block Command for given address range */
-	writew(0x4, &host->regs->wrprot);
+	writenfc(0x4, &host->regs->wrprot);
 
 	return 0;
 }
include/fsl_nfc.h +26 -46

84 lines not on this page · raw message

nand_spl/nand_boot_fsl_nfc.c +25 -22

104 lines not on this page · raw message

Signature · 1 line
1.7.10.4
#1 lore raw

PATCH v3 2/4 nand: mxc: Add support for i.MX5

---
Changes in v3:
- Separate code reformatting from behavioral changes.

Changes in v2: None

 arch/arm/include/asm/arch-mx5/imx-regs.h |    9 +++
 drivers/mtd/nand/mxc_nand.c              |  129 +++++++++++++++++++++++++++---
 include/fsl_nfc.h                        |   79 +++++++++++++++++-
 nand_spl/nand_boot_fsl_nfc.c             |   67 +++++++++++++++-
 4 files changed, 269 insertions(+), 15 deletions(-)
arch/arm/include/asm/arch-mx5/imx-regs.h +9 -0
index 249d15a..9aa0c6a 100644
@@ -224,6 +224,15 @@
 #define CS0_32M_CS1_32M_CS2_32M_CS3_32M		3
 
 /*
+ * SRC register definitions
+ */
+#if defined(CONFIG_MX51)
+#define SRC_SBMR_NF16B		(1 << 2)
+#elif defined(CONFIG_MX53)
+#define SRC_SBMR_NF16B		(1 << 13)
+#endif
+
+/*
  * CSPI register definitions
  */
 #define MXC_ECSPI
drivers/mtd/nand/mxc_nand.c +118 -11

275 lines not on this page · raw message

include/fsl_nfc.h +77 -2

133 lines not on this page · raw message

nand_spl/nand_boot_fsl_nfc.c +65 -2

109 lines not on this page · raw message

Signature · 1 line
1.7.10.4
#2 lore raw

PATCH v3 3/4 imx: mx5: lowlevel_init: Simplify code

In reply to Benoît Thébaudeau

Don't use several instructions to build constant values.

---
Changes in v3:
- New patch.

Changes in v2: None

 arch/arm/cpu/armv7/mx5/lowlevel_init.S |    8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)
arch/arm/cpu/armv7/mx5/lowlevel_init.S +2 -6
index 6d9396a..dfce0ca 100644
@@ -309,8 +309,7 @@ setup_pll_func:
         ldr r0, =CCM_BASE_ADDR
         ldr r1, =0x00015154
         str r1, [r0, #CLKCTL_CBCMR]
-        ldr r1, =0x02888945
-        orr r1, r1, #(1 << 16)
+        ldr r1, =0x02898945
         str r1, [r0, #CLKCTL_CBCDR]
         /* make sure change is effective */
 1:      ldr r1, [r0, #CLKCTL_CDHIPR]
@@ -321,10 +320,7 @@ setup_pll_func:
 
 	/* Switch peripheral to PLL2 */
 	ldr r0, =CCM_BASE_ADDR
-	ldr r1, =0x00808145
-	orr r1, r1, #(2 << 10)
-	orr r1, r1, #(0 << 16)
-	orr r1, r1, #(1 << 19)
+	ldr r1, =0x00888945
 	str r1, [r0, #CLKCTL_CBCDR]
 
 	ldr r1, =0x00016154
Signature · 1 line
1.7.10.4
#3 lore raw

PATCH v3 3/4 imx: mx5: lowlevel_init: Simplify code

Quoted 29 lines · Beno?t Th?baudeau

Don't use several instructions to build constant values.

---
Changes in v3:
- New patch.

Changes in v2: None

 arch/arm/cpu/armv7/mx5/lowlevel_init.S |    8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)
arch/arm/cpu/armv7/mx5/lowlevel_init.S +1 -2
index 6d9396a..dfce0ca 100644
@@ -309,8 +309,7 @@ setup_pll_func:
         ldr r0, =CCM_BASE_ADDR
         ldr r1, =0x00015154
         str r1, [r0, #CLKCTL_CBCMR]
-        ldr r1, =0x02888945
-        orr r1, r1, #(1 << 16)
+        ldr r1, =0x02898945
         str r1, [r0, #CLKCTL_CBCDR]
         /* make sure change is effective */
 1:      ldr r1, [r0, #CLKCTL_CDHIPR]
@@ -321,10 +320,7 @@ setup_pll_func:
 

arch/arm/cpu/armv7/mx5/lowlevel_init.S setup_pll_func: · line 326

Quoted 10 lines
arch/arm/cpu/armv7/mx5/lowlevel_init.S +1 -4
 	/* Switch peripheral to PLL2 */
 	ldr r0, =CCM_BASE_ADDR
-	ldr r1, =0x00808145
-	orr r1, r1, #(2 << 10)
-	orr r1, r1, #(0 << 16)
-	orr r1, r1, #(1 << 19)
+	ldr r1, =0x00888945
 	str r1, [r0, #CLKCTL_CBCDR]
 
 	ldr r1, =0x00016154

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#4 lore raw

PATCH v3 4/4 imx: mx53ard: Add support for NAND Flash

In reply to Benoît Thébaudeau

Add support for the Samsung K9LAG08U0M NAND Flash (2-GiB MLC NAND Flash, 2-kiB pages, 256-kiB blocks, 30-ns R/W cycles, 1 CS) on mx53ard.

eNFC_CLK_ROOT is set up with a cycle time of 37.5 ns (400 MHz / 3 / 5) for this board, which satisfies the 30-ns NF R/W cycle requirement.

---
Changes in v3:
- New patch.

Changes in v2: None

 board/freescale/mx53ard/mx53ard.c |   18 ++++++++++++++++++
 include/configs/mx53ard.h         |   10 ++++++++++
 2 files changed, 28 insertions(+)
board/freescale/mx53ard/mx53ard.c +18 -0
index 2fc8570..8907388 100644
@@ -58,6 +58,23 @@ void dram_init_banksize(void)
 	gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE;
 }
 
+#ifdef CONFIG_NAND_MXC
+static void setup_iomux_nand(void)
+{
+	mxc_request_iomux(MX53_PIN_NANDF_CLE, IOMUX_CONFIG_ALT0);
+	mxc_request_iomux(MX53_PIN_NANDF_ALE, IOMUX_CONFIG_ALT0);
+	mxc_request_iomux(MX53_PIN_NANDF_CS0, IOMUX_CONFIG_ALT0);
+	mxc_request_iomux(MX53_PIN_NANDF_RE_B, IOMUX_CONFIG_ALT0);
+	mxc_request_iomux(MX53_PIN_NANDF_WE_B, IOMUX_CONFIG_ALT0);
+	mxc_request_iomux(MX53_PIN_NANDF_WP_B, IOMUX_CONFIG_ALT0);
+	mxc_request_iomux(MX53_PIN_NANDF_RB0, IOMUX_CONFIG_ALT0);
+}
+#else
+static void setup_iomux_nand(void)
+{
+}
+#endif
+
 static void setup_iomux_uart(void)
 {
 	/* UART1 RXD */
@@ -277,6 +294,7 @@ static void weim_cs1_settings(void)
 
 int board_early_init_f(void)
 {
+	setup_iomux_nand();
 	setup_iomux_uart();
 	return 0;
 }
include/configs/mx53ard.h +10 -0
index 62cb42b..148f7a2 100644
@@ -41,6 +41,16 @@
 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_MXC_GPIO
 
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_BASE		NFC_BASE_ADDR_AXI
+#define CONFIG_NAND_MXC
+#define CONFIG_MXC_NAND_REGS_BASE	NFC_BASE_ADDR_AXI
+#define CONFIG_MXC_NAND_IP_REGS_BASE	NFC_BASE_ADDR
+#define CONFIG_SYS_NAND_LARGEPAGE
+#define CONFIG_MXC_NAND_HWECC
+#define CONFIG_SYS_NAND_USE_FLASH_BBT
+#define CONFIG_CMD_NAND
+
 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE	UART1_BASE
 
Signature · 1 line
1.7.10.4