Skip to contentSkip to conversation

Add generic DMA DT binding support

PATCH Superseded Padmavathi Venna 4 participants 11 messages Feb 6, 2013 – Feb 8, 2013

Subsystems (5)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

v3 cover Add generic DMA DT binding support

Changes since V2:
- Add new filter function for DT case as suggested by Arnd
- Add xlate as static function
- Use newly added filter function in xlate.
- Add Acked-by for some of the patches

Changes since V1:
- Address the review comments by Arnd Bergmann as below
- Wording of the properties.
- Pass pdmac as third parameter to of_dma_controller_register
- Filter the dma channel based on channel number and dma_device

This patch set adds support for generic dma device tree bindings for Samsung platforms and is dependent on the following patches from Vinod Koul next branch
1)of: Add generic device tree DMA helpers
2)dmaengine: add helper function to request a slave DMA channel

This patch set is made based Mark Brown next branch

Padmavathi Venna (5):
DMA: PL330: Add new pl330 filter for DT case.
DMA: PL330: Add xlate function
DMA: PL330: Register the DMA controller with the generic DMA helpers
ARM: dts: Add #dma-cells for generic dma binding support
ARM: SAMSUNG: dma: Remove unnecessary code

 .../devicetree/bindings/dma/arm-pl330.txt          |   15 ++++-
 arch/arm/boot/dts/exynos5250.dtsi                  |    4 +
 arch/arm/mach-s3c24xx/include/mach/dma.h           |    1 -
 arch/arm/mach-s3c64xx/include/mach/dma.h           |    1 -
 arch/arm/plat-samsung/dma-ops.c                    |   10 +---
 arch/arm/plat-samsung/include/plat/dma-ops.h       |    1 -
 arch/arm/plat-samsung/include/plat/dma-pl330.h     |    1 -
 drivers/dma/pl330.c                                |   64 +++++++++++++++----
 8 files changed, 66 insertions(+), 31 deletions(-)
Signature · 1 line
1.7.4.4
#1 lore raw

PATCH v3 1/5 DMA: PL330: Add new pl330 filter for DT case.

This patch adds a new pl330_dt_filter for DT case to filter the required channel based on the new filter params and modifies the old filter only for non-DT case as suggested by Arnd Bergmann.

---
 drivers/dma/pl330.c |   29 +++++++++++++++--------------
 1 files changed, 15 insertions(+), 14 deletions(-)
drivers/dma/pl330.c +15 -14
index 80680ee..87110f2 100644
@@ -606,6 +606,11 @@ struct dma_pl330_desc {
 	struct dma_pl330_chan *pchan;
 };
 
+struct dma_pl330_filter_args {
+	struct dma_pl330_dmac *pdmac;
+	unsigned int chan_id;
+};
+
 static inline void _callback(struct pl330_req *r, enum pl330_op_err err)
 {
 	if (r && r->xfer_cb)
@@ -2352,6 +2357,16 @@ static void dma_pl330_rqcb(void *token, enum pl330_op_err err)
 	tasklet_schedule(&pch->task);
 }
 
+static bool pl330_dt_filter(struct dma_chan *chan, void *param)
+{
+	struct dma_pl330_filter_args *fargs = param;
+
+	if (chan->device != &fargs->pdmac->ddma)
+		return false;
+
+	return (chan->chan_id == fargs->chan_id);
+}
+
 bool pl330_filter(struct dma_chan *chan, void *param)
 {
 	u8 *peri_id;
@@ -2359,20 +2374,6 @@ bool pl330_filter(struct dma_chan *chan, void *param)
 	if (chan->device->dev->driver != &pl330_driver.drv)
 		return false;
 
-#ifdef CONFIG_OF
-	if (chan->device->dev->of_node) {
-		const __be32 *prop_value;
-		phandle phandle;
-		struct device_node *node;
-
-		prop_value = ((struct property *)param)->value;
-		phandle = be32_to_cpup(prop_value++);
-		node = of_find_node_by_phandle(phandle);
-		return ((chan->private == node) &&
-				(chan->chan_id == be32_to_cpup(prop_value)));
-	}
-#endif
-
 	peri_id = chan->private;
 	return *peri_id == (unsigned)param;
 }
Signature · 1 line
1.7.4.4
#3 lore raw

PATCH v3 2/5 DMA: PL330: Add xlate function

In reply to Padmavathi Venna

Add xlate to translate the device-tree binding information into the appropriate format. The filter function requires the dma controller device and dma channel number as filter_params.

---
 drivers/dma/pl330.c |   25 +++++++++++++++++++++++++
 1 files changed, 25 insertions(+), 0 deletions(-)
drivers/dma/pl330.c +25 -0
index 87110f2..e68c83b 100644
@@ -25,6 +25,7 @@
 #include <linux/amba/pl330.h>
 #include <linux/scatterlist.h>
 #include <linux/of.h>
+#include <linux/of_dma.h>
 
 #include "dmaengine.h"
 #define PL330_MAX_CHAN		8
@@ -2379,6 +2380,30 @@ bool pl330_filter(struct dma_chan *chan, void *param)
 }
 EXPORT_SYMBOL(pl330_filter);
 
+static struct dma_chan *of_dma_pl330_xlate(struct of_phandle_args *dma_spec,
+						struct of_dma *ofdma)
+{
+	int count = dma_spec->args_count;
+	struct dma_pl330_dmac *pdmac = ofdma->of_dma_data;
+	struct dma_pl330_filter_args fargs;
+	dma_cap_mask_t cap;
+
+	if (!pdmac)
+		return NULL;
+
+	if (count != 1)
+		return NULL;
+
+	fargs.pdmac = pdmac;
+	fargs.chan_id = dma_spec->args[0];
+
+	dma_cap_zero(cap);
+	dma_cap_set(DMA_SLAVE, cap);
+	dma_cap_set(DMA_CYCLIC, cap);
+
+	return dma_request_channel(cap, pl330_dt_filter, &fargs);
+}
+
 static int pl330_alloc_chan_resources(struct dma_chan *chan)
 {
 	struct dma_pl330_chan *pch = to_pchan(chan);
Signature · 1 line
1.7.4.4
#4 lore raw

PATCH v3 3/5 DMA: PL330: Register the DMA controller with the generic DMA helpers

In reply to Padmavathi Venna

This patch registers the pl330 dma controller driver with the generic device tree dma helper functions.

---
 drivers/dma/pl330.c |   10 ++++++++++
 1 files changed, 10 insertions(+), 0 deletions(-)
drivers/dma/pl330.c +10 -0
index e68c83b..3fca247 100644
@@ -2999,6 +2999,14 @@ pl330_probe(struct amba_device *adev, const struct amba_id *id)
 		pi->pcfg.data_bus_width / 8, pi->pcfg.num_chan,
 		pi->pcfg.num_peri, pi->pcfg.num_events);
 
+	ret = of_dma_controller_register(adev->dev.of_node,
+					 of_dma_pl330_xlate, pdmac);
+	if (ret) {
+		dev_err(&adev->dev,
+		"unable to register DMA to the generic DT DMA helpers\n");
+		goto probe_err2;
+	}
+
 	return 0;
 
 probe_err4:
@@ -3025,6 +3033,8 @@ static int pl330_remove(struct amba_device *adev)
 	if (!pdmac)
 		return 0;
 
+	of_dma_controller_free(adev->dev.of_node);
+
 	amba_set_drvdata(adev, NULL);
 
 	/* Idle the DMAC */
Signature · 1 line
1.7.4.4
#5 lore raw

PATCH v3 4/5 ARM: dts: Add #dma-cells for generic dma binding support

In reply to Padmavathi Venna

This patch adds #dma-cells property to PL330 DMA controller nodes for supporting generic dma dt bindings on samsung exynos5250 platform.

---
 .../devicetree/bindings/dma/arm-pl330.txt          |   15 +++++++++++----
 arch/arm/boot/dts/exynos5250.dtsi                  |    4 ++++
 2 files changed, 15 insertions(+), 4 deletions(-)
Documentation/devicetree/bindings/dma/arm-pl330.txt +11 -4
index 36e27d5..1fdbff6 100644
@@ -8,6 +8,8 @@ Required properties:
   - reg: physical base address of the controller and length of memory mapped
     region.
   - interrupts: interrupt number to the cpu.
+  - #dma-cells: must be <1>. used to represent the number of integer
+    cells in the dmas property of client device.
 
 Optional properties:
 - dma-coherent      : Present if dma operations are coherent
@@ -18,16 +20,21 @@ Example:
 		compatible = "arm,pl330", "arm,primecell";
 		reg = <0x12680000 0x1000>;
 		interrupts = <99>;
+		#dma-cells = <1>;
 	};
 
 Client drivers (device nodes requiring dma transfers from dev-to-mem or
-mem-to-dev) should specify the DMA channel numbers using a two-value pair
+mem-to-dev) should specify the DMA channel numbers and dma channel names
 as shown below.
 
   [property name]  = <[phandle of the dma controller] [dma request id]>;
+  [property name]  = <[dma channel name]>
 
       where 'dma request id' is the dma request number which is connected
-      to the client controller. The 'property name' is recommended to be
-      of the form <name>-dma-channel.
+      to the client controller. The 'property name' 'dmas' and 'dma-names'
+      as required by the generic dma device tree binding helpers. The dma
+      names correspond 1:1 with the dma request ids in the dmas property.
 
-  Example:  tx-dma-channel = <&pdma0 12>;
+  Example:  dmas = <&pdma0 12
+		    &pdma1 11>;
+	    dma-names = "tx", "rx";
arch/arm/boot/dts/exynos5250.dtsi +4 -0
index f50b4e8..724f5bd 100644
@@ -312,24 +312,28 @@
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121A0000 0x1000>;
 			interrupts = <0 34 0>;
+			#dma-cells = <1>;
 		};
 
 		pdma1: pdma@121B0000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121B0000 0x1000>;
 			interrupts = <0 35 0>;
+			#dma-cells = <1>;
 		};
 
 		mdma0: mdma@10800000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x10800000 0x1000>;
 			interrupts = <0 33 0>;
+			#dma-cells = <1>;
 		};
 
 		mdma1: mdma@11C10000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x11C10000 0x1000>;
 			interrupts = <0 124 0>;
+			#dma-cells = <1>;
 		};
 	};
 
Signature · 1 line
1.7.4.4
#6 lore raw

PATCH v3 4/5 ARM: dts: Add #dma-cells for generic dma binding support

Quoted 3 lines · Padmavathi Venna

This patch adds #dma-cells property to PL330 DMA controller nodes for supporting generic dma dt bindings on samsung exynos5250 platform.

The subject doesn't reflect this is for pl330.

Quoted 13 lines
---
 .../devicetree/bindings/dma/arm-pl330.txt          |   15 +++++++++++----
 arch/arm/boot/dts/exynos5250.dtsi                  |    4 ++++
 2 files changed, 15 insertions(+), 4 deletions(-)
Documentation/devicetree/bindings/dma/arm-pl330.txt +0 -0
index 36e27d5..1fdbff6 100644

Documentation/devicetree/bindings/dma/arm-pl330.txt Required properties: · line 12

Quoted 5 lines
Documentation/devicetree/bindings/dma/arm-pl330.txt +2 -0
@@ -8,6 +8,8 @@ Required properties:
   - reg: physical base address of the controller and length of memory mapped
     region.
   - interrupts: interrupt number to the cpu.
+  - #dma-cells: must be <1>. used to represent the number of integer
+    cells in the dmas property of client device.

This should be optional in the case of platforms supporting only memory to memory xfers.

Rob

Quoted 63 lines
Documentation/devicetree/bindings/dma/arm-pl330.txt +9 -4
 Optional properties:
 - dma-coherent      : Present if dma operations are coherent
@@ -18,16 +20,21 @@ Example:
 		compatible = "arm,pl330", "arm,primecell";
 		reg = <0x12680000 0x1000>;
 		interrupts = <99>;
+		#dma-cells = <1>;
 	};
 
 Client drivers (device nodes requiring dma transfers from dev-to-mem or
-mem-to-dev) should specify the DMA channel numbers using a two-value pair
+mem-to-dev) should specify the DMA channel numbers and dma channel names
 as shown below.
 
   [property name]  = <[phandle of the dma controller] [dma request id]>;
+  [property name]  = <[dma channel name]>
 
       where 'dma request id' is the dma request number which is connected
-      to the client controller. The 'property name' is recommended to be
-      of the form <name>-dma-channel.
+      to the client controller. The 'property name' 'dmas' and 'dma-names'
+      as required by the generic dma device tree binding helpers. The dma
+      names correspond 1:1 with the dma request ids in the dmas property.
 
-  Example:  tx-dma-channel = <&pdma0 12>;
+  Example:  dmas = <&pdma0 12
+		    &pdma1 11>;
+	    dma-names = "tx", "rx";
arch/arm/boot/dts/exynos5250.dtsi +4 -0
index f50b4e8..724f5bd 100644
@@ -312,24 +312,28 @@
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121A0000 0x1000>;
 			interrupts = <0 34 0>;
+			#dma-cells = <1>;
 		};
 
 		pdma1: pdma at 121B0000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121B0000 0x1000>;
 			interrupts = <0 35 0>;
+			#dma-cells = <1>;
 		};
 
 		mdma0: mdma at 10800000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x10800000 0x1000>;
 			interrupts = <0 33 0>;
+			#dma-cells = <1>;
 		};
 
 		mdma1: mdma at 11C10000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x11C10000 0x1000>;
 			interrupts = <0 124 0>;
+			#dma-cells = <1>;
 		};
 	};
 
#7 lore raw

PATCH v3 4/5 ARM: dts: Add #dma-cells for generic dma binding support

Hi Rob,

Quoted 6 lines · Rob Herring
Quoted 3 lines · Padmavathi Venna

This patch adds #dma-cells property to PL330 DMA controller nodes for supporting generic dma dt bindings on samsung exynos5250 platform.

The subject doesn't reflect this is for pl330.

OK. I will fix this.

Quoted 9 lines
Quoted 9 lines
---
 .../devicetree/bindings/dma/arm-pl330.txt          |   15 +++++++++++----
 arch/arm/boot/dts/exynos5250.dtsi                  |    4 ++++
 2 files changed, 15 insertions(+), 4 deletions(-)
Quoted 13 lines

Documentation/devicetree/bindings/dma/arm-pl330.txt Required properties: · line 12

Quoted 10 lines
Documentation/devicetree/bindings/dma/arm-pl330.txt +2 -0
index 36e27d5..1fdbff6 100644
@@ -8,6 +8,8 @@ Required properties:
   - reg: physical base address of the controller and length of memory mapped
     region.
   - interrupts: interrupt number to the cpu.
+  - #dma-cells: must be <1>. used to represent the number of integer
+    cells in the dmas property of client device.

This should be optional in the case of platforms supporting only memory to memory xfers.

In Exynos we have support for both peripheral to peripheral and memory to memory.
So I made it as required property. Should I make this as optional?

Quoted 57 lines

Rob

Quoted 54 lines
Documentation/devicetree/bindings/dma/arm-pl330.txt +9 -4
 Optional properties:
 - dma-coherent      : Present if dma operations are coherent
@@ -18,16 +20,21 @@ Example:
              compatible = "arm,pl330", "arm,primecell";
              reg = <0x12680000 0x1000>;
              interrupts = <99>;
+             #dma-cells = <1>;
      };
 
 Client drivers (device nodes requiring dma transfers from dev-to-mem or
-mem-to-dev) should specify the DMA channel numbers using a two-value pair
+mem-to-dev) should specify the DMA channel numbers and dma channel names
 as shown below.
 
   [property name]  = <[phandle of the dma controller] [dma request id]>;
+  [property name]  = <[dma channel name]>
 
       where 'dma request id' is the dma request number which is connected
-      to the client controller. The 'property name' is recommended to be
-      of the form <name>-dma-channel.
+      to the client controller. The 'property name' 'dmas' and 'dma-names'
+      as required by the generic dma device tree binding helpers. The dma
+      names correspond 1:1 with the dma request ids in the dmas property.
 
-  Example:  tx-dma-channel = <&pdma0 12>;
+  Example:  dmas = <&pdma0 12
+                 &pdma1 11>;
+         dma-names = "tx", "rx";
arch/arm/boot/dts/exynos5250.dtsi +3 -0
index f50b4e8..724f5bd 100644
@@ -312,24 +312,28 @@
                      compatible = "arm,pl330", "arm,primecell";
                      reg = <0x121A0000 0x1000>;
                      interrupts = <0 34 0>;
+                     #dma-cells = <1>;
              };
 
              pdma1: pdma at 121B0000 {
                      compatible = "arm,pl330", "arm,primecell";
                      reg = <0x121B0000 0x1000>;
                      interrupts = <0 35 0>;
+                     #dma-cells = <1>;
              };
 
              mdma0: mdma at 10800000 {
                      compatible = "arm,pl330", "arm,primecell";
                      reg = <0x10800000 0x1000>;
                      interrupts = <0 33 0>;
+                     #dma-cells = <1>;
              };
 
Quoted 10 lines

arch/arm/boot/dts/exynos5250.dtsi line 339

Quoted 9 lines
arch/arm/boot/dts/exynos5250.dtsi +1 -0
              mdma1: mdma at 11C10000 {
                      compatible = "arm,pl330", "arm,primecell";
                      reg = <0x11C10000 0x1000>;
                      interrupts = <0 124 0>;
+                     #dma-cells = <1>;
              };
      };
 

Thanks
Padma

#8 lore raw

PATCH v3 4/5 ARM: dts: Add #dma-cells for generic dma binding support

Quoted 33 lines · Padma Venkat

Hi Rob,

Quoted 6 lines · Rob Herring
Quoted 3 lines · Padmavathi Venna

This patch adds #dma-cells property to PL330 DMA controller nodes for supporting generic dma dt bindings on samsung exynos5250 platform.

The subject doesn't reflect this is for pl330.

OK. I will fix this.

Quoted 9 lines
Quoted 9 lines
---
 .../devicetree/bindings/dma/arm-pl330.txt          |   15 +++++++++++----
 arch/arm/boot/dts/exynos5250.dtsi                  |    4 ++++
 2 files changed, 15 insertions(+), 4 deletions(-)
Quoted 13 lines

Documentation/devicetree/bindings/dma/arm-pl330.txt Required properties: · line 12

Quoted 10 lines
Documentation/devicetree/bindings/dma/arm-pl330.txt +2 -0
index 36e27d5..1fdbff6 100644
@@ -8,6 +8,8 @@ Required properties:
   - reg: physical base address of the controller and length of memory mapped
     region.
   - interrupts: interrupt number to the cpu.
+  - #dma-cells: must be <1>. used to represent the number of integer
+    cells in the dmas property of client device.

This should be optional in the case of platforms supporting only memory to memory xfers.

Quoted 3 lines

In Exynos we have support for both peripheral to peripheral and memory to memory.
So I made it as required property. Should I make this as optional?

I believe that is what I said. Highbank has the pl330 and only supports mem to mem transfers.

Rob

Quoted 72 lines
Quoted 58 lines

Rob

Quoted 54 lines
Documentation/devicetree/bindings/dma/arm-pl330.txt +9 -4
 Optional properties:
 - dma-coherent      : Present if dma operations are coherent
@@ -18,16 +20,21 @@ Example:
              compatible = "arm,pl330", "arm,primecell";
              reg = <0x12680000 0x1000>;
              interrupts = <99>;
+             #dma-cells = <1>;
      };
 
 Client drivers (device nodes requiring dma transfers from dev-to-mem or
-mem-to-dev) should specify the DMA channel numbers using a two-value pair
+mem-to-dev) should specify the DMA channel numbers and dma channel names
 as shown below.
 
   [property name]  = <[phandle of the dma controller] [dma request id]>;
+  [property name]  = <[dma channel name]>
 
       where 'dma request id' is the dma request number which is connected
-      to the client controller. The 'property name' is recommended to be
-      of the form <name>-dma-channel.
+      to the client controller. The 'property name' 'dmas' and 'dma-names'
+      as required by the generic dma device tree binding helpers. The dma
+      names correspond 1:1 with the dma request ids in the dmas property.
 
-  Example:  tx-dma-channel = <&pdma0 12>;
+  Example:  dmas = <&pdma0 12
+                 &pdma1 11>;
+         dma-names = "tx", "rx";
arch/arm/boot/dts/exynos5250.dtsi +3 -0
index f50b4e8..724f5bd 100644
@@ -312,24 +312,28 @@
                      compatible = "arm,pl330", "arm,primecell";
                      reg = <0x121A0000 0x1000>;
                      interrupts = <0 34 0>;
+                     #dma-cells = <1>;
              };
 
              pdma1: pdma at 121B0000 {
                      compatible = "arm,pl330", "arm,primecell";
                      reg = <0x121B0000 0x1000>;
                      interrupts = <0 35 0>;
+                     #dma-cells = <1>;
              };
 
              mdma0: mdma at 10800000 {
                      compatible = "arm,pl330", "arm,primecell";
                      reg = <0x10800000 0x1000>;
                      interrupts = <0 33 0>;
+                     #dma-cells = <1>;
              };
 
Quoted 10 lines

arch/arm/boot/dts/exynos5250.dtsi line 339

Quoted 9 lines
arch/arm/boot/dts/exynos5250.dtsi +1 -0
              mdma1: mdma at 11C10000 {
                      compatible = "arm,pl330", "arm,primecell";
                      reg = <0x11C10000 0x1000>;
                      interrupts = <0 124 0>;
+                     #dma-cells = <1>;
              };
      };
 

Thanks
Padma

#9 lore raw

PATCH v3 5/5 ARM: SAMSUNG: dma: Remove unnecessary code

In reply to Padmavathi Venna

This patch removes the usage of DMACH_DT_PROP and dt_dmach_prop from dma code as the new generic dma dt binding support has been added.

---
 arch/arm/mach-s3c24xx/include/mach/dma.h       |    1 -
 arch/arm/mach-s3c64xx/include/mach/dma.h       |    1 -
 arch/arm/plat-samsung/dma-ops.c                |   10 +---------
 arch/arm/plat-samsung/include/plat/dma-ops.h   |    1 -
 arch/arm/plat-samsung/include/plat/dma-pl330.h |    1 -
 5 files changed, 1 insertions(+), 13 deletions(-)
arch/arm/mach-s3c24xx/include/mach/dma.h +0 -1
index 6b72d5a..b55da1d 100644
@@ -24,7 +24,6 @@
 */
 
 enum dma_ch {
-	DMACH_DT_PROP = -1,	/* not yet supported, do not use */
 	DMACH_XD0 = 0,
 	DMACH_XD1,
 	DMACH_SDI,
arch/arm/mach-s3c64xx/include/mach/dma.h +0 -1
index 57b1ff4..fe1a98c 100644
@@ -21,7 +21,6 @@
  */
 enum dma_ch {
 	/* DMA0/SDMA0 */
-	DMACH_DT_PROP = -1, /* not yet supported, do not use */
 	DMACH_UART0 = 0,
 	DMACH_UART0_SRC2,
 	DMACH_UART1,
arch/arm/plat-samsung/dma-ops.c +1 -9
index 71d58dd..ec0d731 100644
@@ -23,23 +23,15 @@ static unsigned samsung_dmadev_request(enum dma_ch dma_ch,
 				struct device *dev, char *ch_name)
 {
 	dma_cap_mask_t mask;
-	void *filter_param;
 
 	dma_cap_zero(mask);
 	dma_cap_set(param->cap, mask);
 
-	/*
-	 * If a dma channel property of a device node from device tree is
-	 * specified, use that as the fliter parameter.
-	 */
-	filter_param = (dma_ch == DMACH_DT_PROP) ?
-		(void *)param->dt_dmach_prop : (void *)dma_ch;
-
 	if (dev->of_node)
 		return (unsigned)dma_request_slave_channel(dev, ch_name);
 	else
 		return (unsigned)dma_request_channel(mask, pl330_filter,
-							filter_param);
+							(void *)dma_ch);
 }
 
 static int samsung_dmadev_release(unsigned ch, void *param)
arch/arm/plat-samsung/include/plat/dma-ops.h +0 -1
index 1141782..ce6d763 100644
@@ -18,7 +18,6 @@
 
 struct samsung_dma_req {
 	enum dma_transaction_type cap;
-	struct property *dt_dmach_prop;
 	struct s3c2410_dma_client *client;
 };
 
arch/arm/plat-samsung/include/plat/dma-pl330.h +0 -1
index d384a80..abe07fa 100644
@@ -21,7 +21,6 @@
  * use these just as IDs.
  */
 enum dma_ch {
-	DMACH_DT_PROP = -1,
 	DMACH_UART0_RX = 0,
 	DMACH_UART0_TX,
 	DMACH_UART1_RX,
Signature · 1 line
1.7.4.4