Skip to contentSkip to conversation

Tegra: All Tamonten-derived boards use onboard NAND

PATCH New Thierry Reding 4 participants 16 messages Feb 14, 2013 – Mar 8, 2013 Tegra architecture support

lore
Share & tools
lore
#0 lore raw

PATCH 1/4 Tegra: All Tamonten-derived boards use onboard NAND

Move the nand-controller node to the tegra20-tamonten.dtsi so that it can be shared between all derived boards.

---
This depends on Tom's "Tegra: MMC: Add DT support for MMC to T20 boards" patches.

 board/avionic-design/dts/tegra20-tamonten.dtsi | 11 +++++++++++
 board/avionic-design/dts/tegra20-tec.dts       | 11 -----------
 2 files changed, 11 insertions(+), 11 deletions(-)
board/avionic-design/dts/tegra20-tamonten.dtsi +11 -0
index 4766aba..0a95ac1 100644
@@ -279,6 +279,17 @@
 		status = "okay";
 	};
 
+	nand-controller at 70008000 {
+		nvidia,wp-gpios = <&gpio 23 0>; /* PC7 */
+		nvidia,width = <8>;
+		nvidia,timing = <26 100 20 80 20 10 12 10 70>;
+
+		nand at 0 {
+			reg = <0>;
+			compatible = "hynix,hy27uf4g2b", "nand-flash";
+		};
+	};
+
 	i2c at 7000c000 {
 		clock-frequency = <400000>;
 		status = "okay";
board/avionic-design/dts/tegra20-tec.dts +0 -11
index 376d279..694682c 100644
@@ -32,17 +32,6 @@
 		clock-frequency = <216000000>;
 	};
 
-	nand-controller at 70008000 {
-		nvidia,wp-gpios = <&gpio 23 0>; /* PC7 */
-		nvidia,width = <8>;
-		nvidia,timing = <26 100 20 80 20 10 12 10 70>;
-
-		nand at 0 {
-			reg = <0>;
-			compatible = "hynix,hy27uf4g2b", "nand-flash";
-		};
-	};
-
 	i2c at 7000c000 {
 		status = "disabled";
 	};
Signature · 1 line
1.8.1.2
#1 lore raw

PATCH 2/4 Tegra: Medcom-Wide: Enable NAND and boot script support

Boot script support brings Medcom-Wide in line with other Tegra boards. In order to enable booting a Linux kernel with initial ramdisk, also add support for the new FIT image type.

---
 include/configs/medcom-wide.h | 34 ++++++++++++++++++++--------------
 1 file changed, 20 insertions(+), 14 deletions(-)
include/configs/medcom-wide.h +20 -14
index bae4ba0..ea8e83f 100644
@@ -44,14 +44,29 @@
 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_LATE_INIT
 
-#define CONFIG_ENV_IS_NOWHERE
-
 /* SD/MMC */
 #define CONFIG_MMC
 #define CONFIG_GENERIC_MMC
 #define CONFIG_TEGRA_MMC
 #define CONFIG_CMD_MMC
 
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+#define CONFIG_FS_EXT4
+#define CONFIG_FS_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FS_GENERIC
+
+/* NAND support */
+#define CONFIG_CMD_NAND
+#define CONFIG_TEGRA_NAND
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+
+/* Environment in NAND, aligned to start of last sector */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET		(SZ_512M - SZ_128K) /* 128K sectors */
+
 /* USB host support */
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_TEGRA
@@ -66,18 +81,6 @@
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_DHCP
 
-#define CONFIG_DOS_PARTITION
-#define CONFIG_EFI_PARTITION
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-
-#define CONFIG_FIT
-
-#define CONFIG_BOOTCOMMAND				\
-	"mmc rescan;"					\
-	"ext2load mmc 0 0x17000000 /boot/uImage;"	\
-	"bootm"
-
 /* LCD support */
 #define CONFIG_LCD
 #define CONFIG_PWM_TEGRA
@@ -85,6 +88,9 @@
 #define LCD_BPP LCD_COLOR16
 #define CONFIG_SYS_WHITE_ON_BLACK
 
+/* support the new (FDT-based) image format */
+#define CONFIG_FIT
+
 #include "tegra-common-post.h"
 
 #endif /* __CONFIG_H */
Signature · 1 line
1.8.1.2
#2 lore raw

PATCH 2/4 Tegra: Medcom-Wide: Enable NAND and boot script support

Quoted 3 lines · Thierry Reding

Boot script support brings Medcom-Wide in line with other Tegra boards. In order to enable booting a Linux kernel with initial ramdisk, also add support for the new FIT image type.

I don't care if you enable FIT on your boards, but I would like to point out that there's no requirement to enable FIT just to support ramdisks. bootz/bootm support separate files/locations/... for ramdisks if you want, and I'm pretty sure I validated it worked once at least.

#3 lore raw

PATCH 2/4 Tegra: Medcom-Wide: Enable NAND and boot script support

Quoted 9 lines · Stephen Warren
Quoted 3 lines · Thierry Reding

Boot script support brings Medcom-Wide in line with other Tegra boards. In order to enable booting a Linux kernel with initial ramdisk, also add support for the new FIT image type.

I don't care if you enable FIT on your boards, but I would like to point out that there's no requirement to enable FIT just to support ramdisks. bootz/bootm support separate files/locations/... for ramdisks if you want, and I'm pretty sure I validated it worked once at least.

Yes, I seem to remember using that as well at some point. In most of our products we ship a single uImage, though, which contains both the zImage and the initrd.gz (when we can support all features on mainline, a DTB will also be part of the same uImage). The main reason why we do this is because it reduces the number of files that need to be distributed.

Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130214/a7bcc31b/attachment.pgp>

#4 lore raw

PATCH 3/4 Tegra: Plutux: Enable NAND and boot script support

In reply to Thierry Reding

Boot script support brings Plutux in line with other Tegra boards. In order to enable booting a Linux kernel with initial ramdisk, also add support for the new FIT image type.

---
 include/configs/plutux.h | 31 +++++++++++++++++++------------
 1 file changed, 19 insertions(+), 12 deletions(-)
include/configs/plutux.h +19 -12
index deee237..3332ea8 100644
@@ -42,8 +42,7 @@
 #define CONFIG_SYS_NS16550_COM1		NV_PA_APB_UARTD_BASE
 
 #define CONFIG_BOARD_EARLY_INIT_F
-
-#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_BOARD_LATE_INIT
 
 /* SD/MMC */
 #define CONFIG_MMC
@@ -51,6 +50,23 @@
 #define CONFIG_TEGRA_MMC
 #define CONFIG_CMD_MMC
 
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+#define CONFIG_FS_EXT4
+#define CONFIG_FS_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FS_GENERIC
+
+/* NAND support */
+#define CONFIG_CMD_NAND
+#define CONFIG_TEGRA_NAND
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+
+/* Environment in NAND, aligned to start of last sector */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET		(SZ_512M - SZ_128K) /* 128K sectors */
+
 /* USB host support */
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_TEGRA
@@ -65,18 +81,9 @@
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_DHCP
 
-#define CONFIG_DOS_PARTITION
-#define CONFIG_EFI_PARTITION
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-
+/* support the new (FDT-based) image format */
 #define CONFIG_FIT
 
-#define CONFIG_BOOTCOMMAND				\
-	"mmc rescan;"					\
-	"ext2load mmc 0 0x17000000 /boot/uImage;"	\
-	"bootm"
-
 #include "tegra-common-post.h"
 
 #endif /* __CONFIG_H */
Signature · 1 line
1.8.1.2
#5 lore raw

PATCH 4/4 Tegra: TEC: Enable boot script support

In reply to Thierry Reding

Boot script support brings TEC in line with other Tegra boards. To enable booting a Linux kernel with initial ramdisk, also include support for the new FIT image type.

---
 include/configs/tec.h | 23 +++++++++++------------
 1 file changed, 11 insertions(+), 12 deletions(-)
include/configs/tec.h +11 -12
index caeb9cd..64f6c65 100644
@@ -50,6 +50,14 @@
 #define CONFIG_TEGRA_MMC
 #define CONFIG_CMD_MMC
 
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+#define CONFIG_FS_EXT4
+#define CONFIG_FS_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FS_GENERIC
+
 /* NAND support */
 #define CONFIG_CMD_NAND
 #define CONFIG_TEGRA_NAND
@@ -73,18 +81,6 @@
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_DHCP
 
-#define CONFIG_DOS_PARTITION
-#define CONFIG_EFI_PARTITION
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-
-#define CONFIG_FIT
-
-#define CONFIG_BOOTCOMMAND				\
-	"mmc rescan;"					\
-	"ext2load mmc 0 0x17000000 /boot/uImage;"	\
-	"bootm"
-
 /* LCD support */
 #define CONFIG_LCD
 #define CONFIG_PWM_TEGRA
@@ -92,6 +88,9 @@
 #define LCD_BPP LCD_COLOR16
 #define CONFIG_SYS_WHITE_ON_BLACK
 
+/* support the new (FDT-based) image format */
+#define CONFIG_FIT
+
 #include "tegra-common-post.h"
 
 #endif /* __CONFIG_H */
Signature · 1 line
1.8.1.2
#6 lore raw

PATCH 1/4 Tegra: All Tamonten-derived boards use onboard NAND

In reply to Thierry Reding

Thierry,

Quoted 57 lines · Thierry Reding

Move the nand-controller node to the tegra20-tamonten.dtsi so that it can be shared between all derived boards.

---
This depends on Tom's "Tegra: MMC: Add DT support for MMC to T20 boards" patches.

 board/avionic-design/dts/tegra20-tamonten.dtsi | 11 +++++++++++
 board/avionic-design/dts/tegra20-tec.dts       | 11 -----------
 2 files changed, 11 insertions(+), 11 deletions(-)
board/avionic-design/dts/tegra20-tamonten.dtsi +11 -0
index 4766aba..0a95ac1 100644
@@ -279,6 +279,17 @@
                status = "okay";
        };
 
+       nand-controller at 70008000 {
+               nvidia,wp-gpios = <&gpio 23 0>; /* PC7 */
+               nvidia,width = <8>;
+               nvidia,timing = <26 100 20 80 20 10 12 10 70>;
+
+               nand at 0 {
+                       reg = <0>;
+                       compatible = "hynix,hy27uf4g2b", "nand-flash";
+               };
+       };
+
        i2c at 7000c000 {
                clock-frequency = <400000>;
                status = "okay";
board/avionic-design/dts/tegra20-tec.dts +0 -12
index 376d279..694682c 100644
@@ -32,17 +32,6 @@
                clock-frequency = <216000000>;
        };
 
-       nand-controller at 70008000 {
-               nvidia,wp-gpios = <&gpio 23 0>; /* PC7 */
-               nvidia,width = <8>;
-               nvidia,timing = <26 100 20 80 20 10 12 10 70>;
-
-               nand at 0 {
-                       reg = <0>;
-                       compatible = "hynix,hy27uf4g2b", "nand-flash";
-               };
-       };
-
        i2c at 7000c000 {
                status = "disabled";
        };
--
Quoted 2 lines

1.8.1.2

I kinda lost track of this patchset. I'd like to move it into u-boot-tegra/next if you think it's ready, but I'm not sure if it conflicts with/works with Stephen's 4th patch of his v2 series ("ARM:
tegra: enable a common set of disk-related commands").

Let me know how you want me to proceed - I'd like to get a PR off to Albert for ARM/master this week if possible.

Thanks,

Tom

#7 lore raw

PATCH 1/4 Tegra: All Tamonten-derived boards use onboard NAND

On Mon, Mar 04, 2013 at 01:46:48PM -0700, Tom Warren wrote:
[...]

Quoted 4 lines

I kinda lost track of this patchset. I'd like to move it into u-boot-tegra/next if you think it's ready, but I'm not sure if it conflicts with/works with Stephen's 4th patch of his v2 series ("ARM:
tegra: enable a common set of disk-related commands").

I can rebase my patches on top of Stephen's work and resend them if it helps.

Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: not available
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130304/eaa935bf/attachment.pgp>

#8 lore raw

PATCH 1/4 Tegra: All Tamonten-derived boards use onboard NAND

Thierry,

Quoted 11 lines · Thierry Reding

On Mon, Mar 04, 2013 at 01:46:48PM -0700, Tom Warren wrote:
[...]

Quoted 4 lines

I kinda lost track of this patchset. I'd like to move it into u-boot-tegra/next if you think it's ready, but I'm not sure if it conflicts with/works with Stephen's 4th patch of his v2 series ("ARM:
tegra: enable a common set of disk-related commands").

I can rebase my patches on top of Stephen's work and resend them if it helps.

Thierry

The only problem I see is that Stephen's patchset isn't exclusively Tegra-based, so I'm not sure I want to bring it into the Tegra tree and cause problems when I do a PR. The other half of the patchset is assigned to Tom Rini.

Stephen - how would you like me to resolve this?

Thanks,

Tom

#9 lore raw

PATCH 1/4 Tegra: All Tamonten-derived boards use onboard NAND

Quoted 14 lines · Tom Warren

Thierry,

Quoted 10 lines · Thierry Reding

On Mon, Mar 04, 2013 at 01:46:48PM -0700, Tom Warren wrote:
[...]

Quoted 4 lines

I kinda lost track of this patchset. I'd like to move it into u-boot-tegra/next if you think it's ready, but I'm not sure if it conflicts with/works with Stephen's 4th patch of his v2 series ("ARM:
tegra: enable a common set of disk-related commands").

I can rebase my patches on top of Stephen's work and resend them if it helps.

Quoted 7 lines
Quoted 1 line

Thierry

The only problem I see is that Stephen's patchset isn't exclusively Tegra-based, so I'm not sure I want to bring it into the Tegra tree and cause problems when I do a PR. The other half of the patchset is assigned to Tom Rini.

Stephen - how would you like me to resolve this?

Hmmm. Thierry's patch series does quite a few things at once.

I'd suggest that Thierry posts a series that /just/ enables NAND support. It should be possible to apply that on its own without any conflicts/dependencies on my series.

Enabling FIT could also be a separate series without any conflicts/dependencies.

A lot of the rest of that series is effectively part of my series, since I ended up enabling all those new options in the various common Tegra config files in my series.

The only thing left over is the removal of the custom definition of CONFIG_BOOTCOMMAND in the AD headers. That should happen after my series.

Re: How to get my series into Tegra's tree. I think it'd be fine to apply my series to the Tegra tree even though it touches disk/partition code if you can get the/a maintainer for that code to ack it. Probably someone like Tom Rini. That way, Thierry's CONFIG_BOOTCOMMAND changes wouldn't have to wait long I hope.

#10 lore raw

PATCH 1/4 Tegra: All Tamonten-derived boards use onboard NAND

Quoted 36 lines · Stephen Warren
Quoted 14 lines · Tom Warren

Thierry,

Quoted 10 lines · Thierry Reding

On Mon, Mar 04, 2013 at 01:46:48PM -0700, Tom Warren wrote:
[...]

Quoted 4 lines

I kinda lost track of this patchset. I'd like to move it into u-boot-tegra/next if you think it's ready, but I'm not sure if it conflicts with/works with Stephen's 4th patch of his v2 series ("ARM:
tegra: enable a common set of disk-related commands").

I can rebase my patches on top of Stephen's work and resend them if it helps.

Quoted 7 lines
Quoted 1 line

Thierry

The only problem I see is that Stephen's patchset isn't exclusively Tegra-based, so I'm not sure I want to bring it into the Tegra tree and cause problems when I do a PR. The other half of the patchset is assigned to Tom Rini.

Stephen - how would you like me to resolve this?

Hmmm. Thierry's patch series does quite a few things at once.

I'd suggest that Thierry posts a series that /just/ enables NAND support. It should be possible to apply that on its own without any conflicts/dependencies on my series.

Enabling FIT could also be a separate series without any conflicts/dependencies.

A lot of the rest of that series is effectively part of my series, since I ended up enabling all those new options in the various common Tegra config files in my series.

Quoted 8 lines

The only thing left over is the removal of the custom definition of CONFIG_BOOTCOMMAND in the AD headers. That should happen after my series.

Re: How to get my series into Tegra's tree. I think it'd be fine to apply my series to the Tegra tree even though it touches disk/partition code if you can get the/a maintainer for that code to ack it. Probably someone like Tom Rini. That way, Thierry's CONFIG_BOOTCOMMAND changes wouldn't have to wait long I hope.

Sorry, kinda dropped the ball on this while I was working on the padcfg changes.

Tom Rini - do you agree with Stephen's approach for the disk parts of his patchset? If so, I can apply it to u-boot-tegra/next today & push.

Thierry - assuming the above happens, can you rework/split your patchset as Stephen outlines above? Then I can apply your patches & push and we'll be ready for a PR early next week after some testing/MAKEALL/etc.

Thanks,

Tom

#11 lore raw

PATCH 1/4 Tegra: All Tamonten-derived boards use onboard NAND

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 48 lines · Tom Warren
Quoted 41 lines · Stephen Warren
Quoted 15 lines · Tom Warren

Thierry,

Quoted 11 lines · Thierry Reding

On Mon, Mar 04, 2013 at 01:46:48PM -0700, Tom Warren wrote:
[...]

Quoted 5 lines

I kinda lost track of this patchset. I'd like to move it into u-boot-tegra/next if you think it's ready, but I'm not sure if it conflicts with/works with Stephen's 4th patch of his v2 series ("ARM: tegra: enable a common set of disk-related commands").

I can rebase my patches on top of Stephen's work and resend them if it helps.

Quoted 7 lines
Quoted 1 line

Thierry

The only problem I see is that Stephen's patchset isn't exclusively Tegra-based, so I'm not sure I want to bring it into the Tegra tree and cause problems when I do a PR. The other half of the patchset is assigned to Tom Rini.

Stephen - how would you like me to resolve this?

Hmmm. Thierry's patch series does quite a few things at once.

I'd suggest that Thierry posts a series that /just/ enables NAND support. It should be possible to apply that on its own without any conflicts/dependencies on my series.

Enabling FIT could also be a separate series without any conflicts/dependencies.

A lot of the rest of that series is effectively part of my series, since I ended up enabling all those new options in the various common Tegra config files in my series.

The only thing left over is the removal of the custom definition of CONFIG_BOOTCOMMAND in the AD headers. That should happen after my series.

Quoted 5 lines

Re: How to get my series into Tegra's tree. I think it'd be fine to apply my series to the Tegra tree even though it touches disk/partition code if you can get the/a maintainer for that code to ack it. Probably someone like Tom Rini. That way, Thierry's CONFIG_BOOTCOMMAND changes wouldn't have to wait long I hope.

Quoted 6 lines

Sorry, kinda dropped the ball on this while I was working on the padcfg changes.

Tom Rini - do you agree with Stephen's approach for the disk parts of his patchset? If so, I can apply it to u-boot-tegra/next today & push.

Can you give me some patchwork links? I'm getting going on another round of pulling things into master today. Thanks!

- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/

iQIcBAEBAgAGBQJROhV4AAoJENk4IS6UOR1WgboP/iZFuJFTOf9lLyR38dNHk66p 7h/wexQRQr7CIMYUwHsS55IStunXNif4Njm9u6ehNbjz45v0vpIVUlV37NjhFG82 3XwTRLvt1w9Aag6h8jB/We+Z73rArhHfpq3dbB5FuyX4n+J3Dq+7sRp7kZkRu7gS skSzcAE5b0eMB6OiPwuG0zkVkMaf0ryYZAzjsRvXgT9302YSigHdM0TnZColzcLt LQREK58EiQiO20DGuTYIyRUzEG9MlSiv9J7GOLbtgdEbXES/P/v40lybvPwtNdre q3UmPrDRCMJ2eqtyVZbTRLEAxN9vUhd11cfDBb2HOSsFTilJkpu1GBaR80nmca3p HgyeHvZnABQ/rvAVRPHP54UT+iXF531Z3CRUF5vQcT0N/JHH1LuyHVuij23b5Fxt LcM51YNijmFkisZVTxgX4mrFNpGmSvP+4jEky+t6Vz26uZ8YYfa26Lwlby6EFrKy Nz8QduohPsuSi92QQjSb5LJn86QxFNwz+20UjXPLilQRet/W5WosGJqdUKdH1aun tkZlUZw7mtu9lIEqJJq4JpNKYP7NoMmDygyob0v+VCUPshqKig6Xs3voQMaAC44i 90OBzokS/Vj/AYJQ7eXwpVsdYkrPc5UXBU70/5QMftEVDR6wk0cLHou18F3wYeQd HpIFPnhpM0/7rMKXchV3
=FTH6
-----END PGP SIGNATURE-----

#12 lore raw

PATCH 1/4 Tegra: All Tamonten-derived boards use onboard NAND

Tom

Quoted 59 lines · Tom Rini

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 48 lines · Tom Warren
Quoted 41 lines · Stephen Warren
Quoted 15 lines · Tom Warren

Thierry,

Quoted 11 lines · Thierry Reding

On Mon, Mar 04, 2013 at 01:46:48PM -0700, Tom Warren wrote:
[...]

Quoted 5 lines

I kinda lost track of this patchset. I'd like to move it into u-boot-tegra/next if you think it's ready, but I'm not sure if it conflicts with/works with Stephen's 4th patch of his v2 series ("ARM: tegra: enable a common set of disk-related commands").

I can rebase my patches on top of Stephen's work and resend them if it helps.

Quoted 7 lines
Quoted 1 line

Thierry

The only problem I see is that Stephen's patchset isn't exclusively Tegra-based, so I'm not sure I want to bring it into the Tegra tree and cause problems when I do a PR. The other half of the patchset is assigned to Tom Rini.

Stephen - how would you like me to resolve this?

Hmmm. Thierry's patch series does quite a few things at once.

I'd suggest that Thierry posts a series that /just/ enables NAND support. It should be possible to apply that on its own without any conflicts/dependencies on my series.

Enabling FIT could also be a separate series without any conflicts/dependencies.

A lot of the rest of that series is effectively part of my series, since I ended up enabling all those new options in the various common Tegra config files in my series.

The only thing left over is the removal of the custom definition of CONFIG_BOOTCOMMAND in the AD headers. That should happen after my series.

Quoted 5 lines

Re: How to get my series into Tegra's tree. I think it'd be fine to apply my series to the Tegra tree even though it touches disk/partition code if you can get the/a maintainer for that code to ack it. Probably someone like Tom Rini. That way, Thierry's CONFIG_BOOTCOMMAND changes wouldn't have to wait long I hope.

Quoted 6 lines

Sorry, kinda dropped the ball on this while I was working on the padcfg changes.

Tom Rini - do you agree with Stephen's approach for the disk parts of his patchset? If so, I can apply it to u-boot-tegra/next today & push.

Quoted 5 lines

Can you give me some patchwork links? I'm getting going on another round of pulling things into master today. Thanks!

- --
Tom

Sure:

http://patchwork.ozlabs.org/patch/224204/
http://patchwork.ozlabs.org/patch/224205/
http://patchwork.ozlabs.org/patch/224206/
http://patchwork.ozlabs.org/patch/224207/

204/205 are assigned to you; 206/207 to me.

Tom

#13 lore raw

PATCH 1/4 Tegra: All Tamonten-derived boards use onboard NAND

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 62 lines · Tom Warren
Quoted 54 lines · Tom Rini
Quoted 53 lines · Tom Warren
Quoted 42 lines · Stephen Warren
Quoted 15 lines · Tom Warren

Thierry,

Quoted 11 lines · Thierry Reding

On Mon, Mar 04, 2013 at 01:46:48PM -0700, Tom Warren
wrote: [...]

Quoted 5 lines

I kinda lost track of this patchset. I'd like to move it into u-boot-tegra/next if you think it's ready, but I'm not sure if it conflicts with/works with Stephen's 4th patch of his v2 series ("ARM: tegra: enable a common set of disk-related commands").

I can rebase my patches on top of Stephen's work and resend them if it helps.

Quoted 7 lines
Quoted 1 line

Thierry

The only problem I see is that Stephen's patchset isn't exclusively Tegra-based, so I'm not sure I want to bring it into the Tegra tree and cause problems when I do a PR. The other half of the patchset is assigned to Tom Rini.

Stephen - how would you like me to resolve this?

Hmmm. Thierry's patch series does quite a few things at once.

I'd suggest that Thierry posts a series that /just/ enables NAND support. It should be possible to apply that on its own without any conflicts/dependencies on my series.

Enabling FIT could also be a separate series without any conflicts/dependencies.

A lot of the rest of that series is effectively part of my series, since I ended up enabling all those new options in the various common Tegra config files in my series.

The only thing left over is the removal of the custom definition of CONFIG_BOOTCOMMAND in the AD headers. That should happen after my series.

Quoted 6 lines

Re: How to get my series into Tegra's tree. I think it'd be fine to apply my series to the Tegra tree even though it touches disk/partition code if you can get the/a maintainer for that code to ack it. Probably someone like Tom Rini. That way, Thierry's CONFIG_BOOTCOMMAND changes wouldn't have to wait long I hope.

Sorry, kinda dropped the ball on this while I was working on the padcfg changes.

Quoted 6 lines
Quoted 3 lines

Tom Rini - do you agree with Stephen's approach for the disk parts of his patchset? If so, I can apply it to u-boot-tegra/next today & push.

Can you give me some patchwork links? I'm getting going on another round of pulling things into master today. Thanks!

Quoted 8 lines

Sure:

http://patchwork.ozlabs.org/patch/224204/
http://patchwork.ozlabs.org/patch/224205/
http://patchwork.ozlabs.org/patch/224206/
http://patchwork.ozlabs.org/patch/224207/

204/205 are assigned to you; 206/207 to me.

OK, ack'd, lets move them along the tegra tree since that's where they're really used.

- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/

iQIcBAEBAgAGBQJROhiQAAoJENk4IS6UOR1Wr50P/RIsDFVP62XXxKOfcpQtAUYX 7QHGLX1+qS58pAFRwclIxs64VzIm2dT5xDplzilABJH8BTE6MnUyKqkKbeP4M8pR dtwsVROHK8QdI09bZWN3sBn8B9derkLlsg58lzK8YooeOHJznQhdCxNXEa99/5HJ WLVx7buxUyMYQINyFQH83pCm9e67R/k7KYmr+D3yyvLLpxSyJI++1BpgRDzNhG74 DHacV6gBqD+bMBS62TTtfxGBOHXZgfrSxxuooFHJa8kJef73xt6LKOWwY6KV/eVj cbk6utg7kiSr50AknVwatIZ+aig/uBuXmoLs6IRIkrgn9fVj4yYmmiLcdgfbqgdU mZSE//EW9xQ2mL6qQDEFOOdqrZ2xs9ipf59LqAzKloh41SAWzpxrr2KSp5jpz7rX mjpMPUMZ7lsWNET8x+1rj22MnFWXtfl3EAHTF3WX1FdvWbm63MRLRYmGEf3LzdXW NuA5vpbQEgjnabwg6IGWcxGtPFKCChePThZ3lsK9DT/ozn4pmlvQMzFGL7PHZjX7 ZJcSW/mHTR5HxZC5P7+sgVbGPpwnuUT/Hia/j0kkM+cyCVaqRka649+fIM3Ozrgh yvpqPu2R6JhbwGECmW6AusFGx8Vi/XXC70XfryymGGJB8tDU/6h0HogYYB9PS21e yxBeqziVVusJSwPqn6E1
=d+6W
-----END PGP SIGNATURE-----

#14 lore raw

PATCH 1/4 Tegra: All Tamonten-derived boards use onboard NAND

Quoted 73 lines · Tom Rini

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 69 lines · Tom Warren
Quoted 54 lines · Tom Rini
Quoted 53 lines · Tom Warren
Quoted 42 lines · Stephen Warren
Quoted 15 lines · Tom Warren

Thierry,

Quoted 11 lines · Thierry Reding

On Mon, Mar 04, 2013 at 01:46:48PM -0700, Tom Warren
wrote: [...]

Quoted 5 lines

I kinda lost track of this patchset. I'd like to move it into u-boot-tegra/next if you think it's ready, but I'm not sure if it conflicts with/works with Stephen's 4th patch of his v2 series ("ARM: tegra: enable a common set of disk-related commands").

I can rebase my patches on top of Stephen's work and resend them if it helps.

Quoted 7 lines
Quoted 1 line

Thierry

The only problem I see is that Stephen's patchset isn't exclusively Tegra-based, so I'm not sure I want to bring it into the Tegra tree and cause problems when I do a PR. The other half of the patchset is assigned to Tom Rini.

Stephen - how would you like me to resolve this?

Hmmm. Thierry's patch series does quite a few things at once.

I'd suggest that Thierry posts a series that /just/ enables NAND support. It should be possible to apply that on its own without any conflicts/dependencies on my series.

Enabling FIT could also be a separate series without any conflicts/dependencies.

A lot of the rest of that series is effectively part of my series, since I ended up enabling all those new options in the various common Tegra config files in my series.

The only thing left over is the removal of the custom definition of CONFIG_BOOTCOMMAND in the AD headers. That should happen after my series.

Quoted 6 lines

Re: How to get my series into Tegra's tree. I think it'd be fine to apply my series to the Tegra tree even though it touches disk/partition code if you can get the/a maintainer for that code to ack it. Probably someone like Tom Rini. That way, Thierry's CONFIG_BOOTCOMMAND changes wouldn't have to wait long I hope.

Sorry, kinda dropped the ball on this while I was working on the padcfg changes.

Quoted 6 lines
Quoted 3 lines

Tom Rini - do you agree with Stephen's approach for the disk parts of his patchset? If so, I can apply it to u-boot-tegra/next today & push.

Can you give me some patchwork links? I'm getting going on another round of pulling things into master today. Thanks!

Sure:

http://patchwork.ozlabs.org/patch/224204/
http://patchwork.ozlabs.org/patch/224205/
http://patchwork.ozlabs.org/patch/224206/
http://patchwork.ozlabs.org/patch/224207/

Quoted 7 lines
Quoted 1 line

204/205 are assigned to you; 206/207 to me.

OK, ack'd, lets move them along the tegra tree since that's where they're really used.

- --
Tom

Will do - thanks.

#15 lore raw

PATCH 1/4 Tegra: All Tamonten-derived boards use onboard NAND

Thierry,

Quoted 74 lines · Tom Warren
Quoted 73 lines · Tom Rini

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 69 lines · Tom Warren
Quoted 54 lines · Tom Rini
Quoted 53 lines · Tom Warren
Quoted 42 lines · Stephen Warren
Quoted 15 lines · Tom Warren

Thierry,

Quoted 11 lines · Thierry Reding

On Mon, Mar 04, 2013 at 01:46:48PM -0700, Tom Warren
wrote: [...]

Quoted 5 lines

I kinda lost track of this patchset. I'd like to move it into u-boot-tegra/next if you think it's ready, but I'm not sure if it conflicts with/works with Stephen's 4th patch of his v2 series ("ARM: tegra: enable a common set of disk-related commands").

I can rebase my patches on top of Stephen's work and resend them if it helps.

Quoted 7 lines
Quoted 1 line

Thierry

The only problem I see is that Stephen's patchset isn't exclusively Tegra-based, so I'm not sure I want to bring it into the Tegra tree and cause problems when I do a PR. The other half of the patchset is assigned to Tom Rini.

Stephen - how would you like me to resolve this?

Hmmm. Thierry's patch series does quite a few things at once.

I'd suggest that Thierry posts a series that /just/ enables NAND support. It should be possible to apply that on its own without any conflicts/dependencies on my series.

Enabling FIT could also be a separate series without any conflicts/dependencies.

A lot of the rest of that series is effectively part of my series, since I ended up enabling all those new options in the various common Tegra config files in my series.

The only thing left over is the removal of the custom definition of CONFIG_BOOTCOMMAND in the AD headers. That should happen after my series.

Quoted 6 lines

Re: How to get my series into Tegra's tree. I think it'd be fine to apply my series to the Tegra tree even though it touches disk/partition code if you can get the/a maintainer for that code to ack it. Probably someone like Tom Rini. That way, Thierry's CONFIG_BOOTCOMMAND changes wouldn't have to wait long I hope.

Sorry, kinda dropped the ball on this while I was working on the padcfg changes.

Quoted 6 lines
Quoted 3 lines

Tom Rini - do you agree with Stephen's approach for the disk parts of his patchset? If so, I can apply it to u-boot-tegra/next today & push.

Can you give me some patchwork links? I'm getting going on another round of pulling things into master today. Thanks!

Sure:

http://patchwork.ozlabs.org/patch/224204/
http://patchwork.ozlabs.org/patch/224205/
http://patchwork.ozlabs.org/patch/224206/
http://patchwork.ozlabs.org/patch/224207/

Quoted 8 lines
Quoted 7 lines
Quoted 1 line

204/205 are assigned to you; 206/207 to me.

OK, ack'd, lets move them along the tegra tree since that's where they're really used.

- --
Tom

Will do - thanks.

I've applied Stephen's patchset to u-boot-tegra/next (on top of my padcfg/ctrl patchset and the T30 MMC patchset). PTAL and either send me new discrete patches as Stephen outlined, or let me know how to apply your patchset individually w/current /next TOT.

Thanks,

Tom