Skip to contentSkip to conversation

tg3: Add 57766 device support.

PATCH In review Michael Chan 2 participants 2 messages Feb 15, 2013

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/5 tg3: Add 57766 device support.

From: Matt Carlson <[email protected]>

The patch also adds a couple of fixes

- For the 57766 and non Ax versions of 57765, bootcode needs to setup the PCIE Fast Training Sequence (FTS) value to prevent transmit hangs. Unfortunately, it does not have enough room in the selfboot case (i.e. devices with no NVRAM). The driver needs to implement this.

- For performance reasons, the 2k DMA engine mode on the 57766 should be enabled and dma size limited to 2k for standard sized packets.

---
 drivers/net/ethernet/broadcom/tg3.c |   18 +++++++++++++++++-
 drivers/net/ethernet/broadcom/tg3.h |    2 ++
 2 files changed, 19 insertions(+), 1 deletions(-)
drivers/net/ethernet/broadcom/tg3.c +17 -1
index b1b3bc0..6e676a7 100644
@@ -332,6 +332,7 @@ static DEFINE_PCI_DEVICE_TABLE(tg3_pci_tbl) = {
 	{PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, TG3PCI_DEVICE_TIGON3_5719)},
 	{PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, TG3PCI_DEVICE_TIGON3_5720)},
 	{PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, TG3PCI_DEVICE_TIGON3_57762)},
+	{PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, TG3PCI_DEVICE_TIGON3_57766)},
 	{PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, TG3PCI_DEVICE_TIGON3_5762)},
 	{PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, TG3PCI_DEVICE_TIGON3_5725)},
 	{PCI_DEVICE(PCI_VENDOR_ID_BROADCOM, TG3PCI_DEVICE_TIGON3_5727)},
@@ -9179,7 +9180,14 @@ static int tg3_reset_hw(struct tg3 *tp, int reset_phy)
 		}
 
 		if (GET_CHIP_REV(tp->pci_chip_rev_id) != CHIPREV_57765_AX) {
-			u32 grc_mode = tr32(GRC_MODE);
+			u32 grc_mode;
+
+			/* Fix transmit hangs */
+			val = tr32(TG3_CPMU_PADRNG_CTL);
+			val |= TG3_CPMU_PADRNG_CTL_RDIV2;
+			tw32(TG3_CPMU_PADRNG_CTL, val);
+
+			grc_mode = tr32(GRC_MODE);
 
 			/* Access the lower 1K of DL PCIE block registers. */
 			val = grc_mode & ~GRC_MODE_PCIE_PORT_MASK;
@@ -9492,6 +9500,14 @@ static int tg3_reset_hw(struct tg3 *tp, int reset_phy)
 	if (tg3_flag(tp, PCI_EXPRESS))
 		rdmac_mode |= RDMAC_MODE_FIFO_LONG_BURST;
 
+	if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_57766) {
+		tp->dma_limit = 0;
+		if (tp->dev->mtu <= ETH_DATA_LEN) {
+			rdmac_mode |= RDMAC_MODE_JMB_2K_MMRR;
+			tp->dma_limit = TG3_TX_BD_DMA_MAX_2K;
+		}
+	}
+
 	if (tg3_flag(tp, HW_TSO_1) ||
 	    tg3_flag(tp, HW_TSO_2) ||
 	    tg3_flag(tp, HW_TSO_3))
drivers/net/ethernet/broadcom/tg3.h +2 -0
index ef6ced2..b676728 100644
@@ -1164,6 +1164,8 @@
 #define  CPMU_MUTEX_GNT_DRIVER		 0x00001000
 #define TG3_CPMU_PHY_STRAP		0x00003664
 #define TG3_CPMU_PHY_STRAP_IS_SERDES	 0x00000020
+#define TG3_CPMU_PADRNG_CTL		0x00003668
+#define  TG3_CPMU_PADRNG_CTL_RDIV2	 0x00040000
 /* 0x3664 --> 0x36b0 unused */
 
 #define TG3_CPMU_EEE_MODE		0x000036b0
Signature · 1 line
1.7.1
maintainer
#1 lore raw

All patches applied, using the updated versions of patches #1 and patch #2.

Can I ask kindly that you start to get into the habit of posting an introductory "[PATCH 0/N] " email so that I can use it's contents in the commit message of a merge commit and also reply to just that one email to say I applied everything?

That would enhance the quality of your submissions and save me an enormous amount of time.

Thanks.