usb: Add new command to set USB 2.0 port test modes
Subsystems (2)
PATCH 1/1 usb: Add new command to set USB 2.0 port test modes
This patch adds a new 'usb test' command, that will set a port to a USB 2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes on both downstream hub ports and ordinary device's upstream ports. In addition, it supports EHCI root hub ports. The command is guarded by the CONFIG_CMD_USB_TEST ifdef (disabled by default).
--- README | 1 + common/cmd_usb.c | 127 ++++++++++++++++++++++++++++++++++++-------- doc/README.usb | 1 + drivers/usb/host/ehci-hcd.c | 32 +++++++---- include/usb_defs.h | 13 +++++ 5 files changed, 140 insertions(+), 34 deletions(-)
README +1 -0
@@ -892,6 +892,7 @@ The following options need to be configured: CONFIG_CMD_TIME * run command and report execution time (ARM specific) CONFIG_CMD_TIMER * access to the system tick timer CONFIG_CMD_USB * USB support + CONFIG_CMD_USB_TEST * USB 2.0 hardware test mode support CONFIG_CMD_CDP * Cisco Discover Protocol support CONFIG_CMD_MFSL * Microblaze FSL support
common/cmd_usb.c +104 -23
176 lines not on this page · raw message
doc/README.usb +1 -0
@@ -80,6 +80,7 @@ CONFIG_USB_UHCI defines the lowlevel part.A lowlevel part must be defined CONFIG_USB_KEYBOARD enables the USB Keyboard CONFIG_USB_STORAGE enables the USB storage devices CONFIG_USB_HOST_ETHER enables USB ethernet adapter support +CONFIG_CMD_USB_TEST enables the 'usb test' command for USB 2.0 test modes USB Host Networking
drivers/usb/host/ehci-hcd.c +21 -11
@@ -602,15 +602,19 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer,int len, srclen;uint32_t reg;uint32_t *status_reg; +int port =le16_to_cpu (req->index) &0xff ;struct ehci_ctrl *ctrl = dev->controller; -if (le16_to_cpu (req->index) >CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS ) { -printf ("The request port(%d) is not configured\n" , -le16_to_cpu (req->index) -1 ); +if (port >CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS ) { +printf ("The request port(%d) is not configured\n" , port -1 );return -1 ; } - status_reg = (uint32_t *)&ctrl->hcor->or_portsc[ -le16_to_cpu (req->index) -1 ]; +if (port && !(ctrl->port_enable_mask & + (1 << (port -1 )))) { +debug ("skip request on disabled port%d\n" , port -1 ); +return 0 ; + } + status_reg = (uint32_t *)&hcor->or_portsc[port -1 ]; srclen =0 ; debug("req=%u (%#x), type=%u (%#x), value=%u, index=%u\n",
@@ -727,7 +731,7 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, tmpbuf[2 ] |=USB_PORT_STAT_C_ENABLE ;if (reg &EHCI_PS_OCC ) tmpbuf[2 ] |=USB_PORT_STAT_C_OVERCURRENT ; -if (ctrl->portreset & (1 <<le16_to_cpu (req->index))) +if (ctrl->portreset & (1 << port)) tmpbuf[2 ] |=USB_PORT_STAT_C_RESET ; srcptr = tmpbuf;
@@ -753,7 +757,7 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, EHCI_PS_IS_LOWSPEED(reg)) {/* Low speed device, give up ownership. */ debug ("port %d low speed --> companion\n" , - req->index -1 ); + port -1 ); reg |=EHCI_PS_PO ;ehci_writel (status_reg, reg);break ;
@@ -779,13 +783,19 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, ret =handshake (status_reg,EHCI_PS_PR ,0 ,2 *1000 );if (!ret) - ctrl->portreset |= -1 <<le16_to_cpu (req->index); + ctrl->portreset |=1 << port;else printf ("port(%d) reset error\n" , -le16_to_cpu (req->index) -1 ); + port -1 ); }break ; +#ifdef CONFIG_CMD_USB_TEST +case USB_PORT_FEAT_TEST : + reg &= ~(0xf <<16 ); + reg |= ((le16_to_cpu (req->index) >>8 ) &0xf ) <<16 ; +ehci_writel (status_reg, reg); +break ; +#endif /* CONFIG_CMD_USB_TEST */ default :debug ("unknown feature %x\n" ,le16_to_cpu (req->value)); goto unknown;
@@ -812,7 +822,7 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, reg = (reg & ~EHCI_PS_CLEAR ) |EHCI_PS_OCC ;break ;case USB_PORT_FEAT_C_RESET : - ctrl->portreset &= ~(1 <<le16_to_cpu (req->index)); + ctrl->portreset &= ~(1 << port);break ;default :debug ("unknown feature %x\n" ,le16_to_cpu (req->value));
include/usb_defs.h +13 -0
@@ -150,6 +150,18 @@#define USB_REQ_SET_IDLE 0x0A#define USB_REQ_SET_PROTOCOL 0x0B +/* Device features */ +#define USB_FEAT_HALT 0x00 +#define USB_FEAT_WAKEUP 0x01 +#define USB_FEAT_TEST 0x02 + +/* Test modes */ +#define USB_TEST_MODE_J 0x01 +#define USB_TEST_MODE_K 0x02 +#define USB_TEST_MODE_SE0_NAK 0x03 +#define USB_TEST_MODE_PACKET 0x04 +#define USB_TEST_MODE_FORCE_ENABLE 0x05 +/* "pipe" definitions */
@@ -208,6 +220,7 @@#define USB_PORT_FEAT_C_SUSPEND 18#define USB_PORT_FEAT_C_OVER_CURRENT 19#define USB_PORT_FEAT_C_RESET 20 +#define USB_PORT_FEAT_TEST 21/* wPortStatus bits */ #define USB_PORT_STAT_CONNECTION 0x0001
Signature · 1 line
1.8.1.3
PATCH 1/1 usb: Add new command to set USB 2.0 port test modes
Quoted 7 lines · Julius Werner
This patch adds a new 'usb test' command, that will set a port to a USB 2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes on both downstream hub ports and ordinary device's upstream ports. In addition, it supports EHCI root hub ports. The command is guarded by the
CONFIG_CMD_USB_TESTifdef (disabled by default).Signed-off-by Julius Werner <[email protected]>
We need to enable this on some target as well or we're adding dead code.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130218/55ba5cbc/attachment.pgp>
PATCH 1/1 usb: Add new command to set USB 2.0 port test modes
Hi Tom,
This patch is not really target specific, it works on all platforms that support USB 2.0. I just wrapped it in a new config option because most people probably won't need it? it is only really useful for hardware verification, so I figured whoever needs it can hack in the config option himself. However, I could also just remove the #ifdef and activate it by default if you prefer that. No new code will get executed unless you type the new command, so it should not have any negative effect besides a negligible code size increase.
PATCH 1/1 usb: Add new command to set USB 2.0 port test modes
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 11 lines · Julius Werner
Hi Tom,
This patch is not really target specific, it works on all platforms that support USB 2.0. I just wrapped it in a new config option because most people probably won't need it? it is only really useful for hardware verification, so I figured whoever needs it can hack in the config option himself. However, I could also just remove the #ifdef and activate it by default if you prefer that. No new code will get executed unless you type the new command, so it should not have any negative effect besides a negligible code size increase.
Well, we should enable it at least on the board config you've tested the code with, and you can show how negligible the size difference is.
The point is that adding code that's not enabled somewhere leads to
bitrot. Thanks!
- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/
iQIcBAEBAgAGBQJRI/rVAAoJENk4IS6UOR1W5yoP/jA1KZaqH/1a+uiF4TkMhOqO 1ureFhSUBG875EqnqJsjdGgYt/SZfwBtku5i+qZDtE5jAN6KpPOEV4grRUAYhWll dWpb503TK9Ow+sJKYk8KF+k+awyMwt60L2gZEYxtl2C8ZCGiC6MzEmA25W24pBKh Vj3g6Sg5tgoFPWFBFFXtP3UNgcIzDrmSE4UJzyzKXInap4dwHt+b6Z6EwZ4+iQ6t ekNYxMlEVgdmw2KeuGmDlvjQpmVpaavMYCEON6NbUuCeg830555ETxzC/k37obDq K+PPITocXiR6dm8J42nBA1kaoaG58oRLjCSFlPogVxQ/VdtuAf2RhX9MOBofBw4j VdyV4d90rTCMHdKqids71gdB2YxqkIVdschN7jjpeNHDUEk54dVB5dAW49UJmxhD SWMF03YAfM055W4F0h2CsoZHr/hYqRwDo2J3ljazCAAsSfYav0kdaI6HzZI1zFmd hjs+ThO3A3Ek+lGsSx3Gh0JKKGv/FyfstnrFMVpF098SNkblN7WP7BmCTcWD6ARq h+GecKlSnguzuOVkDjuLCLgJnPVLY2m4D9ixaTuVMGDgNyFCiC4n/TRamHgG7duW HgEyni0hgk3dV3YV9olFeNPaZv0DW+iF0dkQeUI61KfDl8Xi/2Vc4b0ds53NJQmQ fR0w3/FsjQbksD2/aGac
=eCCl
-----END PGP SIGNATURE-----
PATCH 1/1 usb: Add new command to set USB 2.0 port test modes
I guess you are right about the bit rot, it makes more sense to keep this on so people notice when things break. I have compiled it for smdk5250 (though it's all common and EHCI code, so that should make no difference) and only measured a 1.1k increase in uncompressed code size (less than 0.3%). I will just resubmit this without the ifdefs.
PATCH 1/1 usb: Add new command to set USB 2.0 port test modes
This patch adds a new 'usb test' command, that will set a port to a USB 2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes on both downstream hub ports and ordinary device's upstream ports. In addition, it supports EHCI root hub ports.
--- common/cmd_usb.c | 121 +++++++++++++++++++++++++++++++++++--------- drivers/usb/host/ehci-hcd.c | 30 +++++++---- include/usb_defs.h | 13 +++++ 3 files changed, 130 insertions(+), 34 deletions(-)
common/cmd_usb.c +98 -23
@@ -269,6 +269,22 @@ static void usb_display_config(struct usb_device *dev)printf ("\n" ); } +static struct usb_device *usb_find_device (int devnum) +{ +struct usb_device *dev; +int d; + +for (d =0 ; d <USB_MAX_DEVICE ; d++) { + dev =usb_get_dev_index (d); +if (dev ==NULL ) +return NULL ; +if (dev->devnum == devnum) +return dev; + } + +return NULL ; +} +static inline char *portspeed (int speed) {if (speed ==USB_SPEED_HIGH )
@@ -348,6 +364,66 @@ static void usb_show_tree(struct usb_device *dev)usb_show_tree_graph (dev, &preamble[0 ]); } +static int usb_test (struct usb_device *dev,int port,char * arg) +{ +int mode; + +if (port > dev->maxchild) { +printf ("Device is no hub or does not have %d ports.\n" , port); +return 1 ; + } + +switch (arg[0 ]) { +case 'J' : +case 'j' : +printf ("Setting Test_J mode" ); + mode =USB_TEST_MODE_J ; +break ; +case 'K' : +case 'k' : +printf ("Setting Test_K mode" ); + mode =USB_TEST_MODE_K ; +break ; +case 'S' : +case 's' : +printf ("Setting Test_SE0_NAK mode" ); + mode =USB_TEST_MODE_SE0_NAK ; +break ; +case 'P' : +case 'p' : +printf ("Setting Test_Packet mode" ); + mode =USB_TEST_MODE_PACKET ; +break ; +case 'F' : +case 'f' : +printf ("Setting Test_Force_Enable mode" ); + mode =USB_TEST_MODE_FORCE_ENABLE ; +break ; +default : +printf ("Unrecognized test mode: %s\nAvailable modes: " +"J, K, S[E0_NAK], P[acket], F[orce_Enable]\n" , arg); +return 1 ; + } + +if (port) +printf (" on downstream facing port %d...\n" , port); +else +printf (" on upstream facing port...\n" ); + +if (usb_control_msg (dev,usb_sndctrlpipe (dev,0 ),USB_REQ_SET_FEATURE , + port ?USB_RT_PORT :USB_RECIP_DEVICE , + port ?USB_PORT_FEAT_TEST :USB_FEAT_TEST , + (mode <<8 ) | port, +NULL ,0 ,USB_CNTL_TIMEOUT ) ==-1 ) { +printf ("Error during SET_FEATURE.\n" ); +return 1 ; + }else { +printf ("Test mode successfully set. Use 'usb start' " +"to return to normal operation.\n" ); +return 0 ; + } +} +/****************************************************************************** * usb boot command intepreter. Derived from diskboot
@@ -441,17 +517,9 @@ static int do_usb(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) }return 0 ; }else { -int d; - - i =simple_strtoul (argv[2 ],NULL ,16 ); + i =simple_strtoul (argv[2 ],NULL ,10 );printf ("config for device %d\n" , i); -for (d =0 ; d <USB_MAX_DEVICE ; d++) { - dev =usb_get_dev_index (d); -if (dev ==NULL ) -break ; -if (dev->devnum == i) -break ; - } + dev =usb_find_device (i);if (dev ==NULL ) {printf ("*** No device available ***\n" );return 0 ;
@@ -462,6 +530,18 @@ static int do_usb(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) }return 0 ; } +if (strncmp (argv[1 ],"test" ,4 ) ==0 ) { +if (argc <5 ) +return CMD_RET_USAGE ; + i =simple_strtoul (argv[2 ],NULL ,10 ); + dev =usb_find_device (i); +if (dev ==NULL ) { +printf ("Device %d does not exist.\n" , i); +return 1 ; + } + i =simple_strtoul (argv[3 ],NULL ,10 ); +return usb_test (dev, i, argv[4 ]); + }#ifdef CONFIG_USB_STORAGE if (strncmp (argv[1 ],"stor" ,4 ) ==0 )return usb_stor_info ();
@@ -571,7 +651,6 @@ static int do_usb(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])return CMD_RET_USAGE ; } -#ifdef CONFIG_USB_STORAGE U_BOOT_CMD( usb, 5, 1, do_usb, "USB sub-system",
@@ -580,30 +659,26 @@ U_BOOT_CMD("usb stop [f] - stop USB [f]=force stop\n" "usb tree - show USB device tree\n" "usb info [dev] - show available USB devices\n" +"usb test [dev] [port] [mode] - set USB 2.0 test mode\n" +" (specify port 0 to indicate the device's upstream port)\n" +" Available modes: J, K, S[E0_NAK], P[acket], F[orce_Enable]\n" +#ifdef CONFIG_USB_STORAGE"usb storage - show details of USB storage devices\n" "usb dev [dev] - show or set current USB storage device\n" "usb part [dev] - print partition table of one or all USB storage" -" devices\n" +" devices\n" "usb read addr blk# cnt - read `cnt' blocks starting at block `blk#'\n" " to memory address `addr'\n" "usb write addr blk# cnt - write `cnt' blocks starting@block `blk#'\n" " from memory address `addr'" +#endif /* CONFIG_USB_STORAGE */ ); +#ifdef CONFIG_USB_STORAGE U_BOOT_CMD ( usbboot,3 ,1 , do_usbboot,"boot from USB device" ,"loadAddr dev:part" ); - -#else -U_BOOT_CMD ( - usb,5 ,1 , do_usb, -"USB sub-system" , -"start - start (scan) USB controller\n" -"usb reset - reset (rescan) USB controller\n" -"usb tree - show USB device tree\n" -"usb info [dev] - show available USB devices" -); -#endif +#endif /* CONFIG_USB_STORAGE */
drivers/usb/host/ehci-hcd.c +19 -11
@@ -602,15 +602,19 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer,int len, srclen;uint32_t reg;uint32_t *status_reg; +int port =le16_to_cpu (req->index) &0xff ;struct ehci_ctrl *ctrl = dev->controller; -if (le16_to_cpu (req->index) >CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS ) { -printf ("The request port(%d) is not configured\n" , -le16_to_cpu (req->index) -1 ); +if (port >CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS ) { +printf ("The request port(%d) is not configured\n" , port -1 );return -1 ; } - status_reg = (uint32_t *)&ctrl->hcor->or_portsc[ -le16_to_cpu (req->index) -1 ]; +if (port && !(ctrl->port_enable_mask & + (1 << (port -1 )))) { +debug ("skip request on disabled port%d\n" , port -1 ); +return 0 ; + } + status_reg = (uint32_t *)&hcor->or_portsc[port -1 ]; srclen =0 ; debug("req=%u (%#x), type=%u (%#x), value=%u, index=%u\n",
@@ -727,7 +731,7 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, tmpbuf[2 ] |=USB_PORT_STAT_C_ENABLE ;if (reg &EHCI_PS_OCC ) tmpbuf[2 ] |=USB_PORT_STAT_C_OVERCURRENT ; -if (ctrl->portreset & (1 <<le16_to_cpu (req->index))) +if (ctrl->portreset & (1 << port)) tmpbuf[2 ] |=USB_PORT_STAT_C_RESET ; srcptr = tmpbuf;
@@ -753,7 +757,7 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, EHCI_PS_IS_LOWSPEED(reg)) {/* Low speed device, give up ownership. */ debug ("port %d low speed --> companion\n" , - req->index -1 ); + port -1 ); reg |=EHCI_PS_PO ;ehci_writel (status_reg, reg);break ;
@@ -779,13 +783,17 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, ret =handshake (status_reg,EHCI_PS_PR ,0 ,2 *1000 );if (!ret) - ctrl->portreset |= -1 <<le16_to_cpu (req->index); + ctrl->portreset |=1 << port;else printf ("port(%d) reset error\n" , -le16_to_cpu (req->index) -1 ); + port -1 ); }break ; +case USB_PORT_FEAT_TEST : + reg &= ~(0xf <<16 ); + reg |= ((le16_to_cpu (req->index) >>8 ) &0xf ) <<16 ; +ehci_writel (status_reg, reg); +break ;default :debug ("unknown feature %x\n" ,le16_to_cpu (req->value)); goto unknown;
@@ -812,7 +820,7 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, reg = (reg & ~EHCI_PS_CLEAR ) |EHCI_PS_OCC ;break ;case USB_PORT_FEAT_C_RESET : - ctrl->portreset &= ~(1 <<le16_to_cpu (req->index)); + ctrl->portreset &= ~(1 << port);break ;default :debug ("unknown feature %x\n" ,le16_to_cpu (req->value));
include/usb_defs.h +13 -0
@@ -150,6 +150,18 @@#define USB_REQ_SET_IDLE 0x0A#define USB_REQ_SET_PROTOCOL 0x0B +/* Device features */ +#define USB_FEAT_HALT 0x00 +#define USB_FEAT_WAKEUP 0x01 +#define USB_FEAT_TEST 0x02 + +/* Test modes */ +#define USB_TEST_MODE_J 0x01 +#define USB_TEST_MODE_K 0x02 +#define USB_TEST_MODE_SE0_NAK 0x03 +#define USB_TEST_MODE_PACKET 0x04 +#define USB_TEST_MODE_FORCE_ENABLE 0x05 +/* "pipe" definitions */
@@ -208,6 +220,7 @@#define USB_PORT_FEAT_C_SUSPEND 18#define USB_PORT_FEAT_C_OVER_CURRENT 19#define USB_PORT_FEAT_C_RESET 20 +#define USB_PORT_FEAT_TEST 21/* wPortStatus bits */ #define USB_PORT_STAT_CONNECTION 0x0001
Signature · 1 line
1.8.1.3
PATCH 1/1 usb: Add new command to set USB 2.0 port test modes
Oops... I somehow pulled three lines of other local changes in there that don't belong when I cherry-picked this into my upstream branch. Sorry, will resubmit this once more.
Quoted 303 lines · Julius Werner
This patch adds a new 'usb test' command, that will set a port to a USB 2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes on both downstream hub ports and ordinary device's upstream ports. In addition, it supports EHCI root hub ports.
Signed-off-by Julius Werner <[email protected]>--- common/cmd_usb.c | 121 +++++++++++++++++++++++++++++++++++--------- drivers/usb/host/ehci-hcd.c | 30 +++++++---- include/usb_defs.h | 13 +++++ 3 files changed, 130 insertions(+), 34 deletions(-)common/cmd_usb.c +98
-23@@ -269,6 +269,22 @@ static void usb_display_config(struct usb_device *dev)printf ("\n" ); } +static struct usb_device *usb_find_device (int devnum) +{ +struct usb_device *dev; +int d; + +for (d =0 ; d <USB_MAX_DEVICE ; d++) { + dev =usb_get_dev_index (d); +if (dev ==NULL ) +return NULL ; +if (dev->devnum == devnum) +return dev; + } + +return NULL ; +} +static inline char *portspeed (int speed) {if (speed ==USB_SPEED_HIGH )@@ -348,6 +364,66 @@ static void usb_show_tree(struct usb_device *dev)usb_show_tree_graph (dev, &preamble[0 ]); } +static int usb_test (struct usb_device *dev,int port,char * arg) +{ +int mode; + +if (port > dev->maxchild) { +printf ("Device is no hub or does not have %d ports.\n" , port); +return 1 ; + } + +switch (arg[0 ]) { +case 'J' : +case 'j' : +printf ("Setting Test_J mode" ); + mode =USB_TEST_MODE_J ; +break ; +case 'K' : +case 'k' : +printf ("Setting Test_K mode" ); + mode =USB_TEST_MODE_K ; +break ; +case 'S' : +case 's' : +printf ("Setting Test_SE0_NAK mode" ); + mode =USB_TEST_MODE_SE0_NAK ; +break ; +case 'P' : +case 'p' : +printf ("Setting Test_Packet mode" ); + mode =USB_TEST_MODE_PACKET ; +break ; +case 'F' : +case 'f' : +printf ("Setting Test_Force_Enable mode" ); + mode =USB_TEST_MODE_FORCE_ENABLE ; +break ; +default : +printf ("Unrecognized test mode: %s\nAvailable modes: " +"J, K, S[E0_NAK], P[acket], F[orce_Enable]\n" , arg); +return 1 ; + } + +if (port) +printf (" on downstream facing port %d...\n" , port); +else +printf (" on upstream facing port...\n" ); + +if (usb_control_msg (dev,usb_sndctrlpipe (dev,0 ),USB_REQ_SET_FEATURE , + port ?USB_RT_PORT :USB_RECIP_DEVICE , + port ?USB_PORT_FEAT_TEST :USB_FEAT_TEST , + (mode <<8 ) | port, +NULL ,0 ,USB_CNTL_TIMEOUT ) ==-1 ) { +printf ("Error during SET_FEATURE.\n" ); +return 1 ; + }else { +printf ("Test mode successfully set. Use 'usb start' " +"to return to normal operation.\n" ); +return 0 ; + } +} +/****************************************************************************** * usb boot command intepreter. Derived from diskboot @@ -441,17 +517,9 @@ static int do_usb(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) }return 0 ; }else { -int d; - - i =simple_strtoul (argv[2 ],NULL ,16 ); + i =simple_strtoul (argv[2 ],NULL ,10 );printf ("config for device %d\n" , i); -for (d =0 ; d <USB_MAX_DEVICE ; d++) { - dev =usb_get_dev_index (d); -if (dev ==NULL ) -break ; -if (dev->devnum == i) -break ; - } + dev =usb_find_device (i);if (dev ==NULL ) {printf ("*** No device available ***\n" );return 0 ;@@ -462,6 +530,18 @@ static int do_usb(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) }return 0 ; } +if (strncmp (argv[1 ],"test" ,4 ) ==0 ) { +if (argc <5 ) +return CMD_RET_USAGE ; + i =simple_strtoul (argv[2 ],NULL ,10 ); + dev =usb_find_device (i); +if (dev ==NULL ) { +printf ("Device %d does not exist.\n" , i); +return 1 ; + } + i =simple_strtoul (argv[3 ],NULL ,10 ); +return usb_test (dev, i, argv[4 ]); + }#ifdef CONFIG_USB_STORAGE if (strncmp (argv[1 ],"stor" ,4 ) ==0 )return usb_stor_info ();@@ -571,7 +651,6 @@ static int do_usb(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])return CMD_RET_USAGE ; } -#ifdef CONFIG_USB_STORAGE U_BOOT_CMD( usb, 5, 1, do_usb, "USB sub-system",@@ -580,30 +659,26 @@ U_BOOT_CMD("usb stop [f] - stop USB [f]=force stop\n" "usb tree - show USB device tree\n" "usb info [dev] - show available USB devices\n" +"usb test [dev] [port] [mode] - set USB 2.0 test mode\n" +" (specify port 0 to indicate the device's upstream port)\n" +" Available modes: J, K, S[E0_NAK], P[acket], F[orce_Enable]\n" +#ifdef CONFIG_USB_STORAGE"usb storage - show details of USB storage devices\n" "usb dev [dev] - show or set current USB storage device\n" "usb part [dev] - print partition table of one or all USB storage" -" devices\n" +" devices\n" "usb read addr blk# cnt - read `cnt' blocks starting at block `blk#'\n" " to memory address `addr'\n" "usb write addr blk# cnt - write `cnt' blocks starting at block `blk#'\n" " from memory address `addr'" +#endif /* CONFIG_USB_STORAGE */ ); +#ifdef CONFIG_USB_STORAGE U_BOOT_CMD ( usbboot,3 ,1 , do_usbboot,"boot from USB device" ,"loadAddr dev:part" ); - -#else -U_BOOT_CMD ( - usb,5 ,1 , do_usb, -"USB sub-system" , -"start - start (scan) USB controller\n" -"usb reset - reset (rescan) USB controller\n" -"usb tree - show USB device tree\n" -"usb info [dev] - show available USB devices" -); -#endif +#endif /* CONFIG_USB_STORAGE */ drivers/usb/host/ehci-hcd.c +19
-11@@ -602,15 +602,19 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer,int len, srclen;uint32_t reg;uint32_t *status_reg; +int port =le16_to_cpu (req->index) &0xff ;struct ehci_ctrl *ctrl = dev->controller; -if (le16_to_cpu (req->index) >CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS ) { -printf ("The request port(%d) is not configured\n" , -le16_to_cpu (req->index) -1 ); +if (port >CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS ) { +printf ("The request port(%d) is not configured\n" , port -1 );return -1 ; } - status_reg = (uint32_t *)&ctrl->hcor->or_portsc[ -le16_to_cpu (req->index) -1 ]; +if (port && !(ctrl->port_enable_mask & + (1 << (port -1 )))) { +debug ("skip request on disabled port%d\n" , port -1 ); +return 0 ; + } + status_reg = (uint32_t *)&hcor->or_portsc[port -1 ]; srclen =0 ; debug("req=%u (%#x), type=%u (%#x), value=%u, index=%u\n",@@ -727,7 +731,7 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, tmpbuf[2 ] |=USB_PORT_STAT_C_ENABLE ;if (reg &EHCI_PS_OCC ) tmpbuf[2 ] |=USB_PORT_STAT_C_OVERCURRENT ; -if (ctrl->portreset & (1 <<le16_to_cpu (req->index))) +if (ctrl->portreset & (1 << port)) tmpbuf[2 ] |=USB_PORT_STAT_C_RESET ; srcptr = tmpbuf;@@ -753,7 +757,7 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, EHCI_PS_IS_LOWSPEED(reg)) {/* Low speed device, give up ownership. */ debug ("port %d low speed --> companion\n" , - req->index -1 ); + port -1 ); reg |=EHCI_PS_PO ;ehci_writel (status_reg, reg);break ;@@ -779,13 +783,17 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, ret =handshake (status_reg,EHCI_PS_PR ,0 ,2 *1000 );if (!ret) - ctrl->portreset |= -1 <<le16_to_cpu (req->index); + ctrl->portreset |=1 << port;else printf ("port(%d) reset error\n" , -le16_to_cpu (req->index) -1 ); + port -1 ); }break ; +case USB_PORT_FEAT_TEST : + reg &= ~(0xf <<16 ); + reg |= ((le16_to_cpu (req->index) >>8 ) &0xf ) <<16 ; +ehci_writel (status_reg, reg); +break ;default :debug ("unknown feature %x\n" ,le16_to_cpu (req->value)); goto unknown;@@ -812,7 +820,7 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, reg = (reg & ~EHCI_PS_CLEAR ) |EHCI_PS_OCC ;break ;case USB_PORT_FEAT_C_RESET : - ctrl->portreset &= ~(1 <<le16_to_cpu (req->index)); + ctrl->portreset &= ~(1 << port);break ;default :debug ("unknown feature %x\n" ,le16_to_cpu (req->value));include/usb_defs.h +13
-1@@ -150,6 +150,18 @@#define USB_REQ_SET_IDLE 0x0A#define USB_REQ_SET_PROTOCOL 0x0B +/* Device features */ +#define USB_FEAT_HALT 0x00 +#define USB_FEAT_WAKEUP 0x01 +#define USB_FEAT_TEST 0x02 + +/* Test modes */ +#define USB_TEST_MODE_J 0x01 +#define USB_TEST_MODE_K 0x02 +#define USB_TEST_MODE_SE0_NAK 0x03 +#define USB_TEST_MODE_PACKET 0x04 +#define USB_TEST_MODE_FORCE_ENABLE 0x05 +/* "pipe" definitions */ @@ -208,6 +220,7 @@#define USB_PORT_FEAT_C_SUSPEND 18#define USB_PORT_FEAT_C_OVER_CURRENT 19#define USB_PORT_FEAT_C_RESET 20 +#define USB_PORT_FEAT_TEST 21/* wPortStatus bits */ #define USB_PORT_STAT_CONNECTION 0x0001 --1.8.1.3
PATCH 1/1 usb: Add new command to set USB 2.0 port test modes
This patch adds a new 'usb test' command, that will set a port to a USB 2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes on both downstream hub ports and ordinary device's upstream ports. In addition, it supports EHCI root hub ports.
--- common/cmd_usb.c | 121 +++++++++++++++++++++++++++++++++++--------- drivers/usb/host/ehci-hcd.c | 25 +++++---- include/usb_defs.h | 13 +++++ 3 files changed, 125 insertions(+), 34 deletions(-)
common/cmd_usb.c +98 -23
@@ -269,6 +269,22 @@ static void usb_display_config(struct usb_device *dev)printf ("\n" ); } +static struct usb_device *usb_find_device (int devnum) +{ +struct usb_device *dev; +int d; + +for (d =0 ; d <USB_MAX_DEVICE ; d++) { + dev =usb_get_dev_index (d); +if (dev ==NULL ) +return NULL ; +if (dev->devnum == devnum) +return dev; + } + +return NULL ; +} +static inline char *portspeed (int speed) {if (speed ==USB_SPEED_HIGH )
@@ -348,6 +364,66 @@ static void usb_show_tree(struct usb_device *dev)usb_show_tree_graph (dev, &preamble[0 ]); } +static int usb_test (struct usb_device *dev,int port,char * arg) +{ +int mode; + +if (port > dev->maxchild) { +printf ("Device is no hub or does not have %d ports.\n" , port); +return 1 ; + } + +switch (arg[0 ]) { +case 'J' : +case 'j' : +printf ("Setting Test_J mode" ); + mode =USB_TEST_MODE_J ; +break ; +case 'K' : +case 'k' : +printf ("Setting Test_K mode" ); + mode =USB_TEST_MODE_K ; +break ; +case 'S' : +case 's' : +printf ("Setting Test_SE0_NAK mode" ); + mode =USB_TEST_MODE_SE0_NAK ; +break ; +case 'P' : +case 'p' : +printf ("Setting Test_Packet mode" ); + mode =USB_TEST_MODE_PACKET ; +break ; +case 'F' : +case 'f' : +printf ("Setting Test_Force_Enable mode" ); + mode =USB_TEST_MODE_FORCE_ENABLE ; +break ; +default : +printf ("Unrecognized test mode: %s\nAvailable modes: " +"J, K, S[E0_NAK], P[acket], F[orce_Enable]\n" , arg); +return 1 ; + } + +if (port) +printf (" on downstream facing port %d...\n" , port); +else +printf (" on upstream facing port...\n" ); + +if (usb_control_msg (dev,usb_sndctrlpipe (dev,0 ),USB_REQ_SET_FEATURE , + port ?USB_RT_PORT :USB_RECIP_DEVICE , + port ?USB_PORT_FEAT_TEST :USB_FEAT_TEST , + (mode <<8 ) | port, +NULL ,0 ,USB_CNTL_TIMEOUT ) ==-1 ) { +printf ("Error during SET_FEATURE.\n" ); +return 1 ; + }else { +printf ("Test mode successfully set. Use 'usb start' " +"to return to normal operation.\n" ); +return 0 ; + } +} +/****************************************************************************** * usb boot command intepreter. Derived from diskboot
@@ -441,17 +517,9 @@ static int do_usb(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) }return 0 ; }else { -int d; - - i =simple_strtoul (argv[2 ],NULL ,16 ); + i =simple_strtoul (argv[2 ],NULL ,10 );printf ("config for device %d\n" , i); -for (d =0 ; d <USB_MAX_DEVICE ; d++) { - dev =usb_get_dev_index (d); -if (dev ==NULL ) -break ; -if (dev->devnum == i) -break ; - } + dev =usb_find_device (i);if (dev ==NULL ) {printf ("*** No device available ***\n" );return 0 ;
@@ -462,6 +530,18 @@ static int do_usb(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) }return 0 ; } +if (strncmp (argv[1 ],"test" ,4 ) ==0 ) { +if (argc <5 ) +return CMD_RET_USAGE ; + i =simple_strtoul (argv[2 ],NULL ,10 ); + dev =usb_find_device (i); +if (dev ==NULL ) { +printf ("Device %d does not exist.\n" , i); +return 1 ; + } + i =simple_strtoul (argv[3 ],NULL ,10 ); +return usb_test (dev, i, argv[4 ]); + }#ifdef CONFIG_USB_STORAGE if (strncmp (argv[1 ],"stor" ,4 ) ==0 )return usb_stor_info ();
@@ -571,7 +651,6 @@ static int do_usb(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])return CMD_RET_USAGE ; } -#ifdef CONFIG_USB_STORAGE U_BOOT_CMD( usb, 5, 1, do_usb, "USB sub-system",
@@ -580,30 +659,26 @@ U_BOOT_CMD("usb stop [f] - stop USB [f]=force stop\n" "usb tree - show USB device tree\n" "usb info [dev] - show available USB devices\n" +"usb test [dev] [port] [mode] - set USB 2.0 test mode\n" +" (specify port 0 to indicate the device's upstream port)\n" +" Available modes: J, K, S[E0_NAK], P[acket], F[orce_Enable]\n" +#ifdef CONFIG_USB_STORAGE"usb storage - show details of USB storage devices\n" "usb dev [dev] - show or set current USB storage device\n" "usb part [dev] - print partition table of one or all USB storage" -" devices\n" +" devices\n" "usb read addr blk# cnt - read `cnt' blocks starting at block `blk#'\n" " to memory address `addr'\n" "usb write addr blk# cnt - write `cnt' blocks starting@block `blk#'\n" " from memory address `addr'" +#endif /* CONFIG_USB_STORAGE */ ); +#ifdef CONFIG_USB_STORAGE U_BOOT_CMD ( usbboot,3 ,1 , do_usbboot,"boot from USB device" ,"loadAddr dev:part" ); - -#else -U_BOOT_CMD ( - usb,5 ,1 , do_usb, -"USB sub-system" , -"start - start (scan) USB controller\n" -"usb reset - reset (rescan) USB controller\n" -"usb tree - show USB device tree\n" -"usb info [dev] - show available USB devices" -); -#endif +#endif /* CONFIG_USB_STORAGE */
drivers/usb/host/ehci-hcd.c +14 -11
@@ -602,15 +602,14 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer,int len, srclen;uint32_t reg;uint32_t *status_reg; +int port =le16_to_cpu (req->index) &0xff ;struct ehci_ctrl *ctrl = dev->controller; -if (le16_to_cpu (req->index) >CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS ) { -printf ("The request port(%d) is not configured\n" , -le16_to_cpu (req->index) -1 ); +if (port >CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS ) { +printf ("The request port(%d) is not configured\n" , port -1 );return -1 ; } - status_reg = (uint32_t *)&ctrl->hcor->or_portsc[ -le16_to_cpu (req->index) -1 ]; + status_reg = (uint32_t *)&hcor->or_portsc[port -1 ]; srclen =0 ; debug("req=%u (%#x), type=%u (%#x), value=%u, index=%u\n",
@@ -727,7 +726,7 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, tmpbuf[2 ] |=USB_PORT_STAT_C_ENABLE ;if (reg &EHCI_PS_OCC ) tmpbuf[2 ] |=USB_PORT_STAT_C_OVERCURRENT ; -if (ctrl->portreset & (1 <<le16_to_cpu (req->index))) +if (ctrl->portreset & (1 << port)) tmpbuf[2 ] |=USB_PORT_STAT_C_RESET ; srcptr = tmpbuf;
@@ -753,7 +752,7 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, EHCI_PS_IS_LOWSPEED(reg)) {/* Low speed device, give up ownership. */ debug ("port %d low speed --> companion\n" , - req->index -1 ); + port -1 ); reg |=EHCI_PS_PO ;ehci_writel (status_reg, reg);break ;
@@ -779,13 +778,17 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, ret =handshake (status_reg,EHCI_PS_PR ,0 ,2 *1000 );if (!ret) - ctrl->portreset |= -1 <<le16_to_cpu (req->index); + ctrl->portreset |=1 << port;else printf ("port(%d) reset error\n" , -le16_to_cpu (req->index) -1 ); + port -1 ); }break ; +case USB_PORT_FEAT_TEST : + reg &= ~(0xf <<16 ); + reg |= ((le16_to_cpu (req->index) >>8 ) &0xf ) <<16 ; +ehci_writel (status_reg, reg); +break ;default :debug ("unknown feature %x\n" ,le16_to_cpu (req->value)); goto unknown;
@@ -812,7 +815,7 @@ ehci_submit_root(struct usb_device *dev, unsigned long pipe, void *buffer, reg = (reg & ~EHCI_PS_CLEAR ) |EHCI_PS_OCC ;break ;case USB_PORT_FEAT_C_RESET : - ctrl->portreset &= ~(1 <<le16_to_cpu (req->index)); + ctrl->portreset &= ~(1 << port);break ;default :debug ("unknown feature %x\n" ,le16_to_cpu (req->value));
include/usb_defs.h +13 -0
@@ -150,6 +150,18 @@#define USB_REQ_SET_IDLE 0x0A#define USB_REQ_SET_PROTOCOL 0x0B +/* Device features */ +#define USB_FEAT_HALT 0x00 +#define USB_FEAT_WAKEUP 0x01 +#define USB_FEAT_TEST 0x02 + +/* Test modes */ +#define USB_TEST_MODE_J 0x01 +#define USB_TEST_MODE_K 0x02 +#define USB_TEST_MODE_SE0_NAK 0x03 +#define USB_TEST_MODE_PACKET 0x04 +#define USB_TEST_MODE_FORCE_ENABLE 0x05 +/* "pipe" definitions */
@@ -208,6 +220,7 @@#define USB_PORT_FEAT_C_SUSPEND 18#define USB_PORT_FEAT_C_OVER_CURRENT 19#define USB_PORT_FEAT_C_RESET 20 +#define USB_PORT_FEAT_TEST 21/* wPortStatus bits */ #define USB_PORT_STAT_CONNECTION 0x0001
Signature · 1 line
1.8.1.3