Add BF60x processor support to Blackfin architecture.
Subsystems (2)
v4 cover Add BF60x processor support to Blackfin architecture.
From: Sonic Zhang <[email protected]>
ADSP-BF60x is the new generation Blackfin? dual-core processor announced by Analog Devices in late March, 2012. This patch set adds BF60x processor support to Das U-Boot Blackfin architecture.
For more information, see http://blackfin.uclinux.org .
Changes in v4:
- Remove last blank line in initcode.c.
- Fix all checkpatch issues except for cpu name bf609-0.0. It is use as the link flags and is not an error.
- Remove the values for variables in bf609 config headers whose values are useless.
- Fix checkpatch warning whitespace before semicolon
Changes in v3:
- Remove "DO NOT EDIT THIS FILE" comments in anomaly.h
- Trim the head file to those that are used.
- Fix checkpatch issues in blackfin_cdef.h and blackfin_def.h
- Fix checkpatch issues in serial1.h and serial4.h
Changes in v2:
- Fix checkpatch issues in cgu.h, dde.h and anomaly.h
- Fix checkpatch issues.
- Clean up and merge redundant #ifdef's.
- Spearate declarations and code by a blankline.
- Replace unreable macro in uart structures with normal types.
- Replace unreable macro in uart peripheral portmux configuration with clear inline function.
- Fix all checkpatch issues.
- Remove unrelated dma structure change to separate patch.
- The DMA config MMR on BF60x is 32 bits while it is 16 bits on BF5xx. The different type of config MMR is correct.
- Replace unreable macro in dma structures with normal types.
- Fix all checkpatch issues.
- Replace run-time variable with additional macros when adding 4M byte CPLB entries.
- Fix checkpatch issues.
- Does't change funtion sdh_setup_data() to return void.
- Fix checkpatch issues
- Fix checkpatch issues
Bob Liu (5):
blackfin: bf60x: new processor header files
blackfin: bf60x: add dma support
blackfin: bf60x: support big cplb page
blackfin: bf60x: add gpio support
blackfin: bf60x: add hw watchdog support
Scott Jiang (1):
blackfin: add bf6xx spi driver
Sonic Zhang (4):
blackfin: bf60x: Port blackfin core architecture code to boot on
bf60x.
blackfin: bf60x: add serial support
blackfin: bf60x: add board and headers files to support bf609
blackfin: bf60x: add rsi/sdh support
Steven Miao (1):
blackfin: bf60x: add resume from hibernate
MAINTAINERS | 3 +- arch/blackfin/cpu/cpu.c | 4 +- arch/blackfin/cpu/gpio.c | 36 ++- arch/blackfin/cpu/initcode.c | 384 +++++++++++++++++++- arch/blackfin/cpu/initcode.h | 52 +++ arch/blackfin/cpu/reset.c | 6 + arch/blackfin/cpu/serial.c | 81 +++-- arch/blackfin/cpu/serial.h | 222 +----------- arch/blackfin/cpu/serial1.h | 348 ++++++++++++++++++ arch/blackfin/cpu/serial4.h | 161 ++++++++ arch/blackfin/cpu/start.S | 2 + arch/blackfin/include/asm/blackfin_cdef.h | 3 + arch/blackfin/include/asm/blackfin_def.h | 5 + arch/blackfin/include/asm/blackfin_local.h | 3 + arch/blackfin/include/asm/config-pre.h | 4 + arch/blackfin/include/asm/cplb.h | 31 ++- arch/blackfin/include/asm/dma.h | 81 +++-- arch/blackfin/include/asm/gpio.h | 2 +- arch/blackfin/include/asm/mach-bf533/BF531_def.h | 1 + arch/blackfin/include/asm/mach-bf561/BF561_def.h | 1 + arch/blackfin/include/asm/mach-bf609/BF609_cdef.h | 192 ++++++++++ arch/blackfin/include/asm/mach-bf609/BF609_def.h | 241 ++++++++++++ arch/blackfin/include/asm/mach-bf609/anomaly.h | 97 +++++ arch/blackfin/include/asm/mach-bf609/def_local.h | 5 + arch/blackfin/include/asm/mach-bf609/gpio.h | 151 ++++++++ arch/blackfin/include/asm/mach-bf609/portmux.h | 257 +++++++++++++ arch/blackfin/include/asm/mach-bf609/ports.h | 103 ++++++ arch/blackfin/include/asm/mach-common/bits/cgu.h | 80 ++++ arch/blackfin/include/asm/mach-common/bits/dde.h | 88 +++++ arch/blackfin/include/asm/mach-common/bits/dma.h | 54 +++- arch/blackfin/include/asm/mach-common/bits/mpu.h | 6 +- arch/blackfin/include/asm/mach-common/bits/pll.h | 5 + arch/blackfin/include/asm/mach-common/bits/sdh.h | 38 ++- .../blackfin/include/asm/mach-common/bits/spi6xx.h | 240 ++++++++++++ arch/blackfin/include/asm/mach-common/bits/uart4.h | 66 ++++ arch/blackfin/lib/board.c | 25 ++- arch/blackfin/lib/clocks.c | 112 +++++- arch/blackfin/lib/string.c | 97 +++--- board/bf609-ezkit/Makefile | 55 +++ board/bf609-ezkit/bf609-ezkit.c | 67 ++++ boards.cfg | 1 + common/cmd_reginfo.c | 19 +- drivers/mmc/bfin_sdh.c | 68 +++- drivers/spi/Makefile | 1 + drivers/spi/bfin_spi6xx.c | 308 ++++++++++++++++ include/configs/bf609-ezkit.h | 162 ++++++++ include/configs/bfin_adi_common.h | 12 +- 47 files changed, 3584 insertions(+), 396 deletions(-) create mode 100644 arch/blackfin/cpu/serial1.h create mode 100644 arch/blackfin/cpu/serial4.h create mode 100644 arch/blackfin/include/asm/mach-bf609/BF609_cdef.h create mode 100644 arch/blackfin/include/asm/mach-bf609/BF609_def.h create mode 100644 arch/blackfin/include/asm/mach-bf609/anomaly.h create mode 100644 arch/blackfin/include/asm/mach-bf609/def_local.h create mode 100644 arch/blackfin/include/asm/mach-bf609/gpio.h create mode 100644 arch/blackfin/include/asm/mach-bf609/portmux.h create mode 100644 arch/blackfin/include/asm/mach-bf609/ports.h create mode 100644 arch/blackfin/include/asm/mach-common/bits/cgu.h create mode 100644 arch/blackfin/include/asm/mach-common/bits/dde.h create mode 100644 arch/blackfin/include/asm/mach-common/bits/spi6xx.h create mode 100644 arch/blackfin/include/asm/mach-common/bits/uart4.h create mode 100644 board/bf609-ezkit/Makefile create mode 100644 board/bf609-ezkit/bf609-ezkit.c create mode 100644 drivers/spi/bfin_spi6xx.c create mode 100644 include/configs/bf609-ezkit.h
PATCH v4 1/11 blackfin: bf60x: new processor header files
From: Bob Liu <[email protected]>
Add header files for blackfin new processor bf60x.
---
Changes in v4: None
Changes in v3:
- Remove "DO NOT EDIT THIS FILE" comments in anomaly.h
- Trim the head file to those that are used.
- Fix checkpatch issues in blackfin_cdef.h and blackfin_def.h
Changes in v2:
- Fix checkpatch issues in cgu.h, dde.h and anomaly.h
arch/blackfin/include/asm/blackfin_cdef.h | 3 + arch/blackfin/include/asm/blackfin_def.h | 5 + arch/blackfin/include/asm/blackfin_local.h | 3 + arch/blackfin/include/asm/mach-bf609/BF609_cdef.h | 192 +++++++++++++++ arch/blackfin/include/asm/mach-bf609/BF609_def.h | 241 +++++++++++++++++++ arch/blackfin/include/asm/mach-bf609/anomaly.h | 97 ++++++++ arch/blackfin/include/asm/mach-bf609/def_local.h | 5 + arch/blackfin/include/asm/mach-bf609/portmux.h | 257 +++++++++++++++++++++ arch/blackfin/include/asm/mach-bf609/ports.h | 103 ++++++++ arch/blackfin/include/asm/mach-common/bits/cgu.h | 80 +++++++ arch/blackfin/include/asm/mach-common/bits/dde.h | 88 +++++++ arch/blackfin/include/asm/mach-common/bits/mpu.h | 6 +- arch/blackfin/include/asm/mach-common/bits/pll.h | 5 + 13 files changed, 1084 insertions(+), 1 deletions(-) create mode 100644 arch/blackfin/include/asm/mach-bf609/BF609_cdef.h create mode 100644 arch/blackfin/include/asm/mach-bf609/BF609_def.h create mode 100644 arch/blackfin/include/asm/mach-bf609/anomaly.h create mode 100644 arch/blackfin/include/asm/mach-bf609/def_local.h create mode 100644 arch/blackfin/include/asm/mach-bf609/portmux.h create mode 100644 arch/blackfin/include/asm/mach-bf609/ports.h create mode 100644 arch/blackfin/include/asm/mach-common/bits/cgu.h create mode 100644 arch/blackfin/include/asm/mach-common/bits/dde.h
arch/blackfin/include/asm/blackfin_cdef.h +3 -0
@@ -84,5 +84,8 @@#ifdef __ADSPBF561__# include "mach-bf561/BF561_cdef.h" #endif +#ifdef __ADSPBF609__ +# include "mach-bf609/BF609_cdef.h" +#endif #endif /* __MACH_CDEF_BLACKFIN__ */
arch/blackfin/include/asm/blackfin_def.h +5 -0
@@ -136,5 +136,10 @@# include "mach-bf561/anomaly.h" # include "mach-bf561/def_local.h" #endif +#ifdef __ADSPBF609__ +# include "mach-bf609/BF609_def.h" +# include "mach-bf609/anomaly.h" +# include "mach-bf609/def_local.h" +#endif #endif /* __MACH_DEF_BLACKFIN__ */
arch/blackfin/include/asm/blackfin_local.h +3 -0
@@ -61,6 +61,9 @@extern u_long get_vco (void );extern u_long get_cclk (void );extern u_long get_sclk (void ); +extern u_long get_sclk0 (void ); +extern u_long get_sclk1 (void ); +extern u_long get_dclk (void );# define bfin_revid () (bfin_read_CHIPID() >> 28)
arch/blackfin/include/asm/mach-bf609/BF609_cdef.h new file +192 -0
192 lines not on this page · raw message
arch/blackfin/include/asm/mach-bf609/BF609_def.h new file +241 -0
241 lines not on this page · raw message
arch/blackfin/include/asm/mach-bf609/anomaly.h new file +97 -0
97 lines not on this page · raw message
arch/blackfin/include/asm/mach-bf609/def_local.h new file +5 -0
@@ -0,0 +1,5 @@ +#include "gpio.h" +#include "portmux.h" +#include "ports.h" + +#define CONFIG_BF60x 1/* Linux glue */
arch/blackfin/include/asm/mach-bf609/portmux.h new file +257 -0
257 lines not on this page · raw message
arch/blackfin/include/asm/mach-bf609/ports.h new file +103 -0
103 lines not on this page · raw message
arch/blackfin/include/asm/mach-common/bits/cgu.h new file +80 -0
80 lines not on this page · raw message
arch/blackfin/include/asm/mach-common/bits/dde.h new file +88 -0
88 lines not on this page · raw message
arch/blackfin/include/asm/mach-common/bits/mpu.h +5 -1
@@ -70,7 +70,11 @@#define PAGE_SIZE_4KB 0x00010000/* 4 KB page size */ #define PAGE_SIZE_1MB 0x00020000/* 1 MB page size */ #define PAGE_SIZE_4MB 0x00030000/* 4 MB page size */ -#define PAGE_SIZE_MASK 0x00030000/* the bits for the page_size field */ +#define PAGE_SIZE_16KB 0x00040000/* 16 KB page size */ +#define PAGE_SIZE_64KB 0x00050000/* 64 KB page size */ +#define PAGE_SIZE_16MB 0x00060000/* 16 MB page size */ +#define PAGE_SIZE_64MB 0x00070000/* 64 MB page size */ +#define PAGE_SIZE_MASK 0x00070000/* page_size field mask */ #define PAGE_SIZE_SHIFT 16#define CPLB_L1SRAM 0x00000020/* 0=SRAM mapped in L1, 0=SRAM not mapped to L1 */ #define CPLB_PORTPRIO 0x00000200/* 0=low priority port, 1= high priority port */
arch/blackfin/include/asm/mach-common/bits/pll.h +5 -0
@@ -16,6 +16,8 @@#define MSEL 0x7E00/* Multiplier Select For CCLK/VCO Factors */ #define SPORT_HYST 0x8000/* Enable Additional Hysteresis on SPORT Input Pins */ +#define MSEL_P 9 +/* PLL_DIV Masks */ #define SSEL 0x000F/* System Select */ #define CSEL 0x0030/* Core Select */
@@ -29,6 +31,9 @@#define CCLK_DIV4 CSEL_DIV4#define CCLK_DIV8 CSEL_DIV8 +#define SSEL_P 0 +#define CSEL_P 4 +/* PLL_STAT Masks */ #define ACTIVE_PLLENABLED 0x0001/* Processor In Active Mode With PLL Enabled */ #define FULL_ON 0x0002/* Processor In Full On Mode */
Signature · 1 line
1.7.0.4
PATCH v4 2/11 blackfin: bf60x: Port blackfin core architecture code to boot on bf60x.
In reply to Sonic ZhangFrom: Sonic Zhang <[email protected]>
Set up clocks, DDR controller, Nor flash controller, reboot, serial port. Add new SPI boot modes.
---
Changes in v4:
- Remove last blank line in initcode.c.
Changes in v3: None
Changes in v2:
- Fix checkpatch issues.
- Clean up and merge redundant #ifdef's.
- Spearate declarations and code by a blankline.
arch/blackfin/cpu/cpu.c | 4 +- arch/blackfin/cpu/initcode.c | 325 ++++++++++++++++++++++++++++++-- arch/blackfin/cpu/initcode.h | 52 +++++ arch/blackfin/cpu/reset.c | 6 + arch/blackfin/include/asm/config-pre.h | 4 + arch/blackfin/lib/board.c | 6 + arch/blackfin/lib/clocks.c | 112 +++++++++-- common/cmd_reginfo.c | 19 ++- 8 files changed, 486 insertions(+), 42 deletions(-)
arch/blackfin/cpu/cpu.c +3 -1
@@ -68,7 +68,9 @@ void cpu_init_f(ulong bootflag, ulong loaded_from_ldr)/* Reset upon a double exception rather than just hanging. * Do not do bfin_read on SWRST as that will reset status bits. */ +# ifdef SWRST bfin_write_SWRST (DOUBLE_FAULT ); +# endif #endif serial_early_puts ("Board init flash\n" );
@@ -92,7 +94,7 @@ int irq_init(void)#elif defined(SICA_IMASK0 )bfin_write_SICA_IMASK0 (0 );bfin_write_SICA_IMASK1 (0 ); -#else +#elif defined(SIC_IMASK )bfin_write_SIC_IMASK (0 );#endif /* Set up a dummy NMI handler if needed. */
arch/blackfin/cpu/initcode.c +306 -19
479 lines not on this page · raw message
arch/blackfin/cpu/initcode.h +52 -0
80 lines not on this page · raw message
arch/blackfin/cpu/reset.c +6 -0
@@ -23,6 +23,7 @@ __attribute__ ((__l1_text__, __noreturn__))static void bfin_reset (void ) { +#ifdef SWRST /* Wait for completion of "system" events such as cache line * line fills so that we avoid infinite stalls later on as * much as possible. This code is in L1, so it won't trigger
@@ -66,10 +67,15 @@ static void bfin_reset(void) : "a" (15 * 1) : "LC1", "LB1", "LT1" ); +#endif while (1) +#if defined(__ADSPBF60x__) +bfin_write_RCU0_CTL (0x1 ); +#else /* Issue core reset */ asm("raise 1" ); +#endif }/* We need to trampoline ourselves up into L1 since our linker
arch/blackfin/include/asm/config-pre.h +4 -0
@@ -29,6 +29,8 @@#define BFIN_BOOT_16HOST_DMA 11/* boot ldr from 16-bit host dma */ #define BFIN_BOOT_8HOST_DMA 12/* boot ldr from 8-bit host dma */ #define BFIN_BOOT_NAND 13/* boot ldr from nand flash */ +#define BFIN_BOOT_RSI_MASTER 14/* boot ldr from rsi */ +#define BFIN_BOOT_LP_SLAVE 15/* boot ldr from link port */ #ifndef __ASSEMBLY__static inline const char *get_bfin_boot_mode (int bfin_boot)
@@ -47,6 +49,8 @@ static inline const char *get_bfin_boot_mode(int bfin_boot)case BFIN_BOOT_16HOST_DMA :return "16bit dma" ;case BFIN_BOOT_8HOST_DMA :return "8bit dma" ;case BFIN_BOOT_NAND :return "nand flash" ; +case BFIN_BOOT_RSI_MASTER :return "rsi master" ; +case BFIN_BOOT_LP_SLAVE :return "link port slave" ;default :return "INVALID" ; } }
arch/blackfin/lib/board.c +6 -0
@@ -295,7 +295,13 @@ void board_init_f(ulong bootflag)printf ("Clock: VCO: %s MHz, " ,strmhz (buf,get_vco ()));printf ("Core: %s MHz, " ,strmhz (buf,get_cclk ())); +#if defined(__ADSPBF60x__) +printf ("System0: %s MHz, " ,strmhz (buf,get_sclk0 ())); +printf ("System1: %s MHz, " ,strmhz (buf,get_sclk1 ())); +printf ("Dclk: %s MHz\n" ,strmhz (buf,get_dclk ())); +#else printf ("System: %s MHz\n" ,strmhz (buf,get_sclk ())); +#endif if (CONFIG_MEM_SIZE ) {printf ("RAM: " );
arch/blackfin/lib/clocks.c +91 -21
160 lines not on this page · raw message
common/cmd_reginfo.c +18 -1
@@ -191,7 +191,7 @@ static int do_reginfo(cmd_tbl_t *cmdtp, int flag, int argc,#elif defined(CONFIG_BLACKFIN )puts ("\nSystem Configuration registers\n" ); - +#ifndef __ADSPBF60x__puts ("\nPLL Registers\n" );printf ("\tPLL_DIV: 0x%04x PLL_CTL: 0x%04x\n" ,bfin_read_PLL_DIV (),bfin_read_PLL_CTL ());
@@ -227,7 +227,24 @@ static int do_reginfo(cmd_tbl_t *cmdtp, int flag, int argc,printf ("\tEBIU_SDSTAT: 0x%04x EBIU_SDGCTL: 0x%08x\n" ,bfin_read_EBIU_SDSTAT (),bfin_read_EBIU_SDGCTL ());# endif +#else +puts ("\nCGU Registers\n" ); +printf ("\tCGU_DIV: 0x%08x CGU_CTL: 0x%08x\n" , +bfin_read_CGU_DIV (),bfin_read_CGU_CTL ()); +printf ("\tCGU_STAT: 0x%08x CGU_LOCKCNT: 0x%08x\n" , +bfin_read_CGU_STAT (),bfin_read_CGU_CLKOUTSEL ()); +puts ("\nSMC DDR Registers\n" ); +printf ("\tDDR_CFG: 0x%08x DDR_TR0: 0x%08x\n" , +bfin_read_DMC0_CFG (),bfin_read_DMC0_TR0 ()); +printf ("\tDDR_TR1: 0x%08x DDR_TR2: 0x%08x\n" , +bfin_read_DMC0_TR1 (),bfin_read_DMC0_TR2 ()); +printf ("\tDDR_MR: 0x%08x DDR_EMR1: 0x%08x\n" , +bfin_read_DMC0_MR (),bfin_read_DMC0_EMR1 ()); +printf ("\tDDR_CTL: 0x%08x DDR_STAT: 0x%08x\n" , +bfin_read_DMC0_CTL (),bfin_read_DMC0_STAT ()); +printf ("\tDDR_DLLCTL:0x%08x\n" ,bfin_read_DMC0_DLLCTL ()); +#endif #endif /* CONFIG_BLACKFIN */ return 0 ;
Signature · 1 line
1.7.0.4
PATCH v4 3/11 blackfin: bf60x: add serial support
In reply to Sonic ZhangFrom: Sonic Zhang <[email protected]>
Add serial for bf60x.
---
Changes in v4: None
Changes in v3:
- Fix checkpatch issues in serial1.h and serial4.h
Changes in v2:
- Replace unreable macro in uart structures with normal types.
- Replace unreable macro in uart peripheral portmux configuration with clear inline function.
arch/blackfin/cpu/serial.c | 81 +++-- arch/blackfin/cpu/serial.h | 222 +------------ arch/blackfin/cpu/serial1.h | 348 ++++++++++++++++++++ arch/blackfin/cpu/serial4.h | 161 +++++++++ arch/blackfin/include/asm/mach-bf533/BF531_def.h | 1 + arch/blackfin/include/asm/mach-bf561/BF561_def.h | 1 + arch/blackfin/include/asm/mach-common/bits/uart4.h | 66 ++++ 7 files changed, 642 insertions(+), 238 deletions(-) create mode 100644 arch/blackfin/cpu/serial1.h create mode 100644 arch/blackfin/cpu/serial4.h create mode 100644 arch/blackfin/include/asm/mach-common/bits/uart4.h
arch/blackfin/cpu/serial.c +49 -32
@@ -43,7 +43,6 @@#include <serial.h> #include <linux/compiler.h> #include <asm/blackfin.h> -#include <asm/mach-common/bits/uart.h> DECLARE_GLOBAL_DATA_PTR ;
@@ -52,8 +51,8 @@ DECLARE_GLOBAL_DATA_PTR;#include "serial.h" #ifdef CONFIG_DEBUG_SERIAL -static uint16_t cached_lsr[256 ]; -static uint16_t cached_rbr[256 ]; +static uart_lsr_t cached_lsr[256 ]; +static uart_lsr_t cached_rbr[256 ];static size_t cache_count;/* The LSR is read-to-clear on some parts, so we have to make sure status
@@ -61,10 +60,10 @@ static size_t cache_count;* works around anomaly 05000099 at the same time by keeping a cumulative * tally of all the status bits. */ -static uint16_t uart_lsr_save; -static uint16_t uart_lsr_read (uint32_t uart_base) +static uart_lsr_t uart_lsr_save; +static uart_lsr_t uart_lsr_read (uint32_t uart_base) { -uint16_t lsr =bfin_read (&pUART->lsr); +uart_lsr_t lsr =_lsr_read (pUART); uart_lsr_save |= (lsr & (OE |PE |FE |BI ));return lsr | uart_lsr_save; }
@@ -72,20 +71,20 @@ static uint16_t uart_lsr_read(uint32_t uart_base)static void uart_lsr_clear (uint32_t uart_base) { uart_lsr_save =0 ; -bfin_write (&pUART->lsr,bfin_read (&pUART->lsr) |-1 ); +_lsr_write (pUART,-1 ); }#else /* When debugging is disabled, we only care about the DR bit, so if other * bits get set/cleared, we don't really care since we don't read them * anyways (and thus anomaly 05000099 is irrelevant). */ -static inline uint16_t uart_lsr_read (uint32_t uart_base) +static inline uart_lsr_t uart_lsr_read (uint32_t uart_base) { -return bfin_read (&pUART->lsr); +return _lsr_read (pUART); }static void uart_lsr_clear (uint32_t uart_base) { -bfin_write (&pUART->lsr,bfin_read (&pUART->lsr) |-1 ); +_lsr_write (pUART,-1 ); }#endif
@@ -127,20 +126,14 @@ static int uart_getc(uint32_t uart_base) #ifdef CONFIG_DEBUG_SERIAL /* grab & clear the LSR */ - uint16_t uart_lsr_val = uart_lsr_read(uart_base); + uart_lsr_t uart_lsr_val = uart_lsr_read(uart_base); cached_lsr[cache_count] = uart_lsr_val; cached_rbr[cache_count] = uart_rbr_val; cache_count = (cache_count + 1) % ARRAY_SIZE(cached_lsr); if (uart_lsr_val & (OE|PE|FE|BI)) { - uint16_t dll, dlh; printf("\n[SERIAL ERROR]\n"); - ACCESS_LATCH(); - dll = bfin_read(&pUART->dll); - dlh = bfin_read(&pUART->dlh); - ACCESS_PORT_IER(); - printf("\tDLL=0x%x DLH=0x%x\n", dll, dlh); do { --cache_count; printf("\t%3zu: RBR=0x%02x LSR=0x%02x\n", cache_count,
@@ -160,6 +153,8 @@ static int uart_getc(uint32_t uart_base)# define LOOP (x)#endif +#if BFIN_UART_HW_VER <4 + LOOP( static void uart_loop(uint32_t uart_base, int state) {
@@ -178,6 +173,28 @@ static void uart_loop(uint32_t uart_base, int state) } ) +#else + +LOOP ( +static void uart_loop(uint32_t uart_base, int state) +{ + u32 control; + +/* Drain the TX fifo first so bytes don't come back */ +while (!(uart_lsr_read (uart_base) &TEMT )) +continue ; + + control =bfin_read (&pUART->control); +if (state) + control |=LOOP_ENA |MRTS ; +else + control &= ~(LOOP_ENA |MRTS ); +bfin_write (&pUART->control, control); +} +) + +#endif +#ifdef CONFIG_SYS_BFIN_UART static void uart_puts (uint32_t uart_base,const char *s)
@@ -246,16 +263,16 @@ struct serial_device bfin_serial##n##_device = { \ LOOP(.loop = uart##n##_loop) \ }; -#ifdef UART0_DLL +#ifdef UART0_RBR DECL_BFIN_UART(0)#endif -#ifdef UART1_DLL +#ifdef UART1_RBR DECL_BFIN_UART(1)#endif -#ifdef UART2_DLL +#ifdef UART2_RBR DECL_BFIN_UART(2)#endif -#ifdef UART3_DLL +#ifdef UART3_RBR DECL_BFIN_UART(3)#endif
@@ -274,16 +291,16 @@ __weak struct serial_device *default_serial_console(void)void bfin_serial_initialize (void ) { -#ifdef UART0_DLL +#ifdef UART0_RBR serial_register (&bfin_serial0_device);#endif -#ifdef UART1_DLL +#ifdef UART1_RBR serial_register (&bfin_serial1_device);#endif -#ifdef UART2_DLL +#ifdef UART2_RBR serial_register (&bfin_serial2_device);#endif -#ifdef UART3_DLL +#ifdef UART3_RBR serial_register (&bfin_serial3_device);#endif }
@@ -293,7 +310,7 @@ void bfin_serial_initialize(void)/* Symbol for our assembly to call. */ void serial_set_baud (uint32_t baud) { -serial_early_set_baud (UART_DLL , baud); +serial_early_set_baud (UART_BASE , baud); }/* Symbol for common u-boot code to call.
@@ -307,7 +324,7 @@ void serial_setbrg(void)/* Symbol for our assembly to call. */ void serial_initialize (void ) { -serial_early_init (UART_DLL ); +serial_early_init (UART_BASE ); }/* Symbol for common u-boot code to call. */
@@ -315,23 +332,23 @@ int serial_init(void) {serial_initialize ();serial_setbrg (); -uart_lsr_clear (UART_DLL ); +uart_lsr_clear (UART_BASE );return 0 ; }int serial_tstc (void ) { -return uart_tstc (UART_DLL ); +return uart_tstc (UART_BASE ); }int serial_getc (void ) { -return uart_getc (UART_DLL ); +return uart_getc (UART_BASE ); }void serial_putc (const char c) { -uart_putc (UART_DLL , c); +uart_putc (UART_BASE , c); }void serial_puts (const char *s)
@@ -343,7 +360,7 @@ void serial_puts(const char *s)LOOP ( void serial_loop(int state) { -uart_loop (UART_DLL , state); +uart_loop (UART_BASE , state); } )
arch/blackfin/cpu/serial.h +16 -206
261 lines not on this page · raw message
arch/blackfin/cpu/serial1.h new file +348 -0
348 lines not on this page · raw message
arch/blackfin/cpu/serial4.h new file +161 -0
161 lines not on this page · raw message
arch/blackfin/include/asm/mach-bf533/BF531_def.h +1 -0
@@ -149,6 +149,7 @@#define UART_LSR 0xFFC00414#define UART_SCR 0xFFC0041C#define UART_RBR 0xFFC00400/* Receive Buffer */ +#define UART0_RBR UART_RBR#define UART_GCTL 0xFFC00424#define SPT0_TX_CONFIG0 0xFFC00800#define SPT0_TX_CONFIG1 0xFFC00804
arch/blackfin/include/asm/mach-bf561/BF561_def.h +1 -0
@@ -690,6 +690,7 @@#define PPI1_FRAME 0xFFC01310#define UART_THR 0xFFC00400#define UART_RBR 0xFFC00400 +#define UART0_RBR UART_RBR#define UART_DLL 0xFFC00400#define UART_DLH 0xFFC00404#define UART_IER 0xFFC00404
arch/blackfin/include/asm/mach-common/bits/uart4.h new file +66 -0
66 lines not on this page · raw message
Signature · 1 line
1.7.0.4
PATCH v4 4/11 blackfin: bf60x: add dma support
In reply to Sonic ZhangFrom: Bob Liu <[email protected]>
Add dma support for bf60x.
---
Changes in v4: None
Changes in v3: None
Changes in v2:
- Fix all checkpatch issues.
- Remove unrelated dma structure change to separate patch.
- The DMA config MMR on BF60x is 32 bits while it is 16 bits on BF5xx. The different type of config MMR is correct.
- Replace unreable macro in dma structures with normal types.
arch/blackfin/include/asm/dma.h | 81 ++++++++++++------ arch/blackfin/include/asm/mach-common/bits/dma.h | 54 +++++++++++- arch/blackfin/lib/string.c | 97 ++++++++++++---------- 3 files changed, 156 insertions(+), 76 deletions(-)
arch/blackfin/include/asm/dma.h +55 -26
@@ -8,7 +8,12 @@ #ifndef _BLACKFIN_DMA_H_ #define _BLACKFIN_DMA_H_ +#include <linux/types.h> +#ifdef __ADSPBF60x__ +#include <asm/mach-common/bits/dde.h> +#else #include <asm/mach-common/bits/dma.h> +#endif struct dmasg_large { void *next_desc_addr;
@@ -30,46 +35,70 @@ struct dmasg { } __attribute__((packed));struct dma_register { +#ifdef __ADSPBF60x__ +void *next_desc_ptr;/* DMA Next Descriptor Pointer register */ +u32 start_addr;/* DMA Start address register */ +u32 config;/* DMA Configuration register */ + +u32 x_count;/* DMA x_count register */ +s32 x_modify;/* DMA x_modify register */ +u32 y_count;/* DMA y_count register */ +s32 y_modify;/* DMA y_modify register */ +u32 __pad0[2 ]; + +void *curr_desc_ptr;/* DMA Curr Descriptor Pointer register */ +void *prev_desc_ptr;/* DMA Prev Descriptor Pointer register */ +void *curr_addr;/* DMA Current Address Pointer register */ +u32 status;/* DMA irq status register */ +u32 curr_x_count;/* DMA Current x-count register */ +u32 curr_y_count;/* DMA Current y-count register */ +u32 __pad1[2 ]; + +u32 bw_limit;/* DMA Bandwidth Limit Count */ +u32 curr_bw_limit;/* DMA curr Bandwidth Limit Count */ +u32 bw_monitor;/* DMA Bandwidth Monitor Count */ +u32 curr_bw_monitor;/* DMA curr Bandwidth Monitor Count */ +#else void *next_desc_ptr;/* DMA Next Descriptor Pointer register */ -unsigned long start_addr;/* DMA Start address register */ +u32 start_addr;/* DMA Start address register */ -unsigned short cfg;/* DMA Configuration register */ -unsigned short dummy1;/* DMA Configuration register */ +u16 config;/* DMA Configuration register */ +u16 dummy1;/* DMA Configuration register */ -unsigned long reserved; +u32 reserved; -unsigned short x_count;/* DMA x_count register */ -unsigned short dummy2; +u16 x_count;/* DMA x_count register */ +u16 dummy2; -short x_modify;/* DMA x_modify register */ -unsigned short dummy3; +s16 x_modify;/* DMA x_modify register */ +u16 dummy3; -unsigned short y_count;/* DMA y_count register */ -unsigned short dummy4; +u16 y_count;/* DMA y_count register */ +u16 dummy4; -short y_modify;/* DMA y_modify register */ -unsigned short dummy5; +s16 y_modify;/* DMA y_modify register */ +u16 dummy5; -void *curr_desc_ptr;/* DMA Current Descriptor Pointer -register */ -unsigned long curr_addr_ptr;/* DMA Current Address Pointer -register */ -unsigned short irq_status;/* DMA irq status register */ -unsigned short dummy6; +void *curr_desc_ptr;/* DMA Current Descriptor Pointer register */ -unsigned short peripheral_map;/* DMA peripheral map register */ -unsigned short dummy7; +u32 curr_addr_ptr;/* DMA Current Address Pointer register */ -unsigned short curr_x_count;/* DMA Current x-count register */ -unsigned short dummy8; +u16 status;/* DMA irq status register */ +u16 dummy6; -unsigned long reserved2; +u16 peripheral_map;/* DMA peripheral map register */ +u16 dummy7; -unsigned short curr_y_count;/* DMA Current y-count register */ -unsigned short dummy9; +u16 curr_x_count;/* DMA Current x-count register */ +u16 dummy8; -unsigned long reserved3; +u32 reserved2; +u16 curr_y_count;/* DMA Current y-count register */ +u16 dummy9; + +u32 reserved3; +#endif };#endif
arch/blackfin/include/asm/mach-common/bits/dma.h +49 -5
91 lines not on this page · raw message
arch/blackfin/lib/string.c +52 -45
140 lines not on this page · raw message
Signature · 1 line
1.7.0.4
PATCH v4 5/11 blackfin: bf60x: support big cplb page
In reply to Sonic ZhangFrom: Bob Liu <[email protected]>
BF60x support 16K, 64K, 16M and 64M cplb pages, this patch add support for them. So that bf609-ezkit can use it's 128M memory.
---
Changes in v4: None
Changes in v3: None
Changes in v2:
- Fix all checkpatch issues.
- Replace run-time variable with additional macros when adding 4M byte CPLB entries.
arch/blackfin/include/asm/cplb.h | 31 +++++++++++++++++++++++++++---- arch/blackfin/lib/board.c | 19 +++++++++++++++++-- 2 files changed, 44 insertions(+), 6 deletions(-)
arch/blackfin/include/asm/cplb.h +27 -4
@@ -46,8 +46,13 @@#define CPLB_IDOCACHE CPLB_INOCACHE | CPLB_L1_CHBL/* Data Attibutes*/ - -#define SDRAM_IGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID) +#if defined(__ADSPBF60x__) +#define SDRAM_IGENERIC (PAGE_SIZE_16MB | CPLB_L1_CHBL | \ + CPLB_USER_RD | CPLB_VALID) +#else +#define SDRAM_IGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | \ + CPLB_USER_RD | CPLB_VALID) +#endif #define SDRAM_IKERNEL (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)#define L1_IMEMORY (PAGE_SIZE_1MB | CPLB_USER_RD | CPLB_VALID | CPLB_LOCK)#define SDRAM_INON_CHBL (PAGE_SIZE_4MB | CPLB_USER_RD | CPLB_VALID)
@@ -59,14 +64,32 @@#endif #ifdef CONFIG_DCACHE_WB /*Write Back Policy */ -#define SDRAM_DGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND) +#if defined(__ADSPBF60x__) +#define SDRAM_DGENERIC (PAGE_SIZE_16MB | CPLB_L1_CHBL | CPLB_DIRTY | \ + CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | \ + CPLB_VALID | ANOMALY_05000158_WORKAROUND) +#else +#define SDRAM_DGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_DIRTY | \ + CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | \ + CPLB_VALID | ANOMALY_05000158_WORKAROUND) +#endif #define SDRAM_DNON_CHBL (PAGE_SIZE_4MB | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_USER_RD | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158_WORKAROUND)#define SDRAM_DKERNEL (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_USER_RD | CPLB_USER_WR | CPLB_DIRTY | CPLB_SUPV_WR | CPLB_VALID | CPLB_LOCK | ANOMALY_05000158_WORKAROUND)#define L1_DMEMORY (PAGE_SIZE_4MB | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND)#define SDRAM_EBIU (PAGE_SIZE_4MB | CPLB_DIRTY | CPLB_USER_RD | CPLB_USER_WR | CPLB_SUPV_WR | CPLB_VALID | ANOMALY_05000158_WORKAROUND)#else /*Write Through */ -#define SDRAM_DGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW | CPLB_SUPV_WR | CPLB_USER_RD | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158_WORKAROUND) +#if defined(__ADSPBF60x__) +#define SDRAM_DGENERIC (PAGE_SIZE_16MB | CPLB_L1_CHBL | CPLB_WT | \ + CPLB_L1_AOW | CPLB_SUPV_WR | CPLB_USER_RD | \ + CPLB_USER_WR | CPLB_VALID | \ + ANOMALY_05000158_WORKAROUND) +#else +#define SDRAM_DGENERIC (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_WT | \ + CPLB_L1_AOW | CPLB_SUPV_WR | CPLB_USER_RD | \ + CPLB_USER_WR | CPLB_VALID | \ + ANOMALY_05000158_WORKAROUND) +#endif #define SDRAM_DNON_CHBL (PAGE_SIZE_4MB | CPLB_WT | CPLB_L1_AOW | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_USER_RD | CPLB_VALID | ANOMALY_05000158_WORKAROUND)#define SDRAM_DKERNEL (PAGE_SIZE_4MB | CPLB_L1_CHBL | CPLB_WT | CPLB_L1_AOW | CPLB_USER_RD | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_VALID | CPLB_LOCK | ANOMALY_05000158_WORKAROUND)#define L1_DMEMORY (PAGE_SIZE_4MB | CPLB_SUPV_WR | CPLB_USER_WR | CPLB_VALID | ANOMALY_05000158_WORKAROUND)
arch/blackfin/lib/board.c +17 -2
@@ -96,6 +96,13 @@ static void display_global_data(void)#define CPLB_PAGE_SIZE (4 * 1024 * 1024)#define CPLB_PAGE_MASK (~(CPLB_PAGE_SIZE - 1)) +#if defined(__ADSPBF60x__) +#define CPLB_EX_PAGE_SIZE (16 * 1024 * 1024) +#define CPLB_EX_PAGE_MASK (~(CPLB_EX_PAGE_SIZE - 1)) +#else +#define CPLB_EX_PAGE_SIZE CPLB_PAGE_SIZE +#define CPLB_EX_PAGE_MASK CPLB_PAGE_MASK +#endif void init_cplbtables (void ) {volatile uint32_t *ICPLB_ADDR , *ICPLB_DATA ;
@@ -127,6 +134,11 @@ void init_cplbtables(void)icplb_add (0xFFA00000 ,L1_IMEMORY );dcplb_add (0xFF800000 ,L1_DMEMORY ); ++i; +#if defined(__ADSPBF60x__) +icplb_add (0x0 ,0x0 ); +dcplb_add (CONFIG_SYS_FLASH_BASE ,SDRAM_EBIU ); + ++i; +#endif if (CONFIG_MEM_SIZE ) {uint32_t mbase =CONFIG_SYS_MONITOR_BASE ;
@@ -150,9 +162,11 @@ void init_cplbtables(void) } } +#ifndef __ADSPBF60x__icplb_add (0x20000000 ,SDRAM_INON_CHBL );dcplb_add (0x20000000 ,SDRAM_EBIU ); ++i; +#endif /* Add entries for the rest of external RAM up to the bootrom */ extern_memory =0 ;
@@ -167,10 +181,11 @@ void init_cplbtables(void) ++i;#endif -while (i <16 && extern_memory < (CONFIG_SYS_MONITOR_BASE &CPLB_PAGE_MASK )) { +while (i <16 && extern_memory < + (CONFIG_SYS_MONITOR_BASE &CPLB_EX_PAGE_MASK )) {icplb_add (extern_memory,SDRAM_IGENERIC );dcplb_add (extern_memory,SDRAM_DGENERIC ); - extern_memory +=CPLB_PAGE_SIZE ; + extern_memory +=CPLB_EX_PAGE_SIZE ; ++i; }while (i <16 ) {
Signature · 1 line
1.7.0.4
PATCH v4 6/11 blackfin: bf60x: add gpio support
In reply to Sonic ZhangFrom: Bob Liu <[email protected]>
---
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/blackfin/cpu/gpio.c | 36 +++++-- arch/blackfin/include/asm/gpio.h | 2 +- arch/blackfin/include/asm/mach-bf609/gpio.h | 151 +++++++++++++++++++++++++++ 3 files changed, 181 insertions(+), 8 deletions(-) create mode 100644 arch/blackfin/include/asm/mach-bf609/gpio.h
arch/blackfin/cpu/gpio.c +29 -7
@@ -66,6 +66,14 @@ static struct gpio_port_t * const gpio_array[] = { (struct gpio_port_t *)PORTH_FER, (struct gpio_port_t *)PORTI_FER, (struct gpio_port_t *)PORTJ_FER, +#elif defined(CONFIG_BF60x) + (struct gpio_port_t *)PORTA_FER , + (struct gpio_port_t *)PORTB_FER , + (struct gpio_port_t *)PORTC_FER , + (struct gpio_port_t *)PORTD_FER , + (struct gpio_port_t *)PORTE_FER , + (struct gpio_port_t *)PORTF_FER , + (struct gpio_port_t *)PORTG_FER, #else # error no gpio arrays defined #endif
@@ -216,6 +224,12 @@ static void port_setup(unsigned gpio, unsigned short usage) else gpio_array[gpio_bank(gpio)]->port_fer |= gpio_bit(gpio);SSYNC (); +#elif defined(CONFIG_BF60x) +if (usage ==GPIO_USAGE ) + gpio_array[gpio_bank (gpio)]->port_fer_clear =gpio_bit (gpio); +else + gpio_array[gpio_bank (gpio)]->port_fer_set =gpio_bit (gpio); +SSYNC ();#endif }
@@ -290,7 +304,7 @@ static void portmux_setup(unsigned short per) } } } -#elif defined(CONFIG_BF54x) +#elif defined(CONFIG_BF54x) || defined(CONFIG_BF60x)inline void portmux_setup (unsigned short per) {u32 pmux;
@@ -330,7 +344,7 @@ inline void portmux_setup(unsigned short per)# define portmux_setup (...) do { } while (0)#endif -#ifndef CONFIG_BF54x +#if !defined(CONFIG_BF54x) && !defined(CONFIG_BF60x)/*********************************************************** * * FUNCTIONS: Blackfin General Purpose Ports Access Functions
@@ -534,7 +548,7 @@ int peripheral_request(unsigned short per, const char *label)* be requested and used by several drivers */ -#ifdef CONFIG_BF54x +#if defined(CONFIG_BF54x) || defined(CONFIG_BF60x)if (!((per &P_MAYSHARE ) &&get_portmux (per) ==P_FUNCT2MUX (per))) {#else if (!(per &P_MAYSHARE )) {
@@ -651,7 +665,7 @@ int bfin_gpio_request(unsigned gpio, const char *label) gpio, get_label(gpio));return -EBUSY ; } -#ifndef CONFIG_BF54x +#if !defined(CONFIG_BF54x) && !defined(CONFIG_BF60x) else { /* Reset POLAR setting when acquiring a gpio for the first time */set_gpio_polar (gpio,0 ); }
@@ -732,12 +746,16 @@ void bfin_special_gpio_free(unsigned gpio)static inline void __bfin_gpio_direction_input (unsigned gpio) { -#ifdef CONFIG_BF54x +#if defined(CONFIG_BF54x) || defined(CONFIG_BF60x) gpio_array[gpio_bank (gpio)]->dir_clear =gpio_bit (gpio);#else gpio_array[gpio_bank (gpio)]->dir &= ~gpio_bit (gpio);#endif +#if defined(CONFIG_BF60x) + gpio_array[gpio_bank (gpio)]->inen_set =gpio_bit (gpio); +#else gpio_array[gpio_bank (gpio)]->inen |=gpio_bit (gpio); +#endif }int bfin_gpio_direction_input (unsigned gpio)
@@ -785,9 +803,13 @@ int bfin_gpio_direction_output(unsigned gpio, int value)local_irq_save (flags); +#if defined(CONFIG_BF60x) + gpio_array[gpio_bank (gpio)]->inen_clear =gpio_bit (gpio); +#else gpio_array[gpio_bank (gpio)]->inen &= ~gpio_bit (gpio); +#endif gpio_set_value (gpio, value); -#ifdef CONFIG_BF54x +#if defined(CONFIG_BF54x) || defined(CONFIG_BF60x) gpio_array[gpio_bank (gpio)]->dir_set =gpio_bit (gpio);#else gpio_array[gpio_bank (gpio)]->dir |=gpio_bit (gpio);
@@ -801,7 +823,7 @@ int bfin_gpio_direction_output(unsigned gpio, int value)int bfin_gpio_get_value (unsigned gpio) { -#ifdef CONFIG_BF54x +#if defined(CONFIG_BF54x) || defined(CONFIG_BF60x)return (1 & (gpio_array[gpio_bank (gpio)]->data >>gpio_sub_n (gpio)));#else unsigned long flags;
arch/blackfin/include/asm/gpio.h +1 -1
@@ -68,7 +68,7 @@#ifndef __ASSEMBLY__ -#ifndef CONFIG_BF54x +#if !defined(CONFIG_BF54x) && !defined(CONFIG_BF60x)void set_gpio_dir (unsigned ,unsigned short );void set_gpio_inen (unsigned ,unsigned short );void set_gpio_polar (unsigned ,unsigned short );
arch/blackfin/include/asm/mach-bf609/gpio.h new file +151 -0
151 lines not on this page · raw message
Signature · 1 line
1.7.0.4
PATCH v4 7/11 blackfin: bf60x: add board and headers files to support bf609
In reply to Sonic ZhangFrom: Sonic Zhang <[email protected]>
Board and config header files for bf609-ezkit support.
---
Changes in v4:
- Fix all checkpatch issues except for cpu name bf609-0.0. It is use as the link flags and is not an error.
- Remove the values for variables in bf609 config headers whose values are useless.
Changes in v3: None
Changes in v2: None
MAINTAINERS | 3 +- board/bf609-ezkit/Makefile | 55 +++++++++++++ board/bf609-ezkit/bf609-ezkit.c | 67 +++++++++++++++ boards.cfg | 1 + include/configs/bf609-ezkit.h | 161 +++++++++++++++++++++++++++++++++++++ include/configs/bfin_adi_common.h | 12 ++-- 6 files changed, 292 insertions(+), 7 deletions(-) create mode 100644 board/bf609-ezkit/Makefile create mode 100644 board/bf609-ezkit/bf609-ezkit.c create mode 100644 include/configs/bf609-ezkit.h
MAINTAINERS +2 -1
@@ -1214,7 +1214,7 @@ Yoshihiro Shimoda <[email protected]> # Board CPU # ######################################################################### -Mike Frysinger <[email protected]> +Sonic Zhang <[email protected]> Blackfin Team <[email protected]> BF506F-EZKIT BF506
@@ -1231,6 +1231,7 @@ Blackfin Team <[email protected]> BF538F-EZKIT BF538 BF548-EZKIT BF548 BF561-EZKIT BF561 + BF609-EZKIT BF609 M.Hasewinkel (MHA) <[email protected]>
board/bf609-ezkit/Makefile new file +55 -0
55 lines not on this page · raw message
board/bf609-ezkit/bf609-ezkit.c new file +67 -0
67 lines not on this page · raw message
boards.cfg +1 -0
@@ -356,6 +356,7 @@ bf538f-ezkit blackfin blackfin bf548-ezkit blackfin blackfin bf561-acvilon blackfin blackfin bf561-ezkit blackfin blackfin +bf609-ezkit blackfin blackfin blackstamp blackfin blackfin blackvme blackfin blackfin br4 blackfin blackfin
include/configs/bf609-ezkit.h new file +161 -0
161 lines not on this page · raw message
include/configs/bfin_adi_common.h +6 -6
@@ -10,7 +10,7 @@*/ #ifndef _CONFIG_CMD_DEFAULT_H# include <config_cmd_default.h> -# if ADI_CMDS_NETWORK +# ifdef ADI_CMDS_NETWORK # define CONFIG_CMD_DHCP # define CONFIG_BOOTP_SUBNETMASK # define CONFIG_BOOTP_GATEWAY
@@ -58,7 +58,7 @@# endif # ifdef CONFIG_RTC_BFIN # define CONFIG_CMD_DATE -# if ADI_CMDS_NETWORK +# ifdef ADI_CMDS_NETWORK # define CONFIG_CMD_SNTP # endif # endif
@@ -193,10 +193,10 @@"nand erase 0 0x40000;" \ "nand write $(loadaddr) 0 0x40000"# else -# define UBOOT_ENV_UPDATE \ - "protect off 0x20000000 +$(filesize);" \ - "erase 0x20000000 +$(filesize);" \ - "cp.b $(loadaddr) 0x20000000 $(filesize)" +# define UBOOT_ENV_UPDATE \ + "protect off " MK_STR(CONFIG_SYS_FLASH_BASE) " +$(filesize);" \ + "erase " MK_STR(CONFIG_SYS_FLASH_BASE) " +$(filesize);" \ + "cp.b $(loadaddr)" MK_STR(CONFIG_SYS_FLASH_BASE) " $(filesize)"# endif # ifdef CONFIG_NETCONSOLE # define NETCONSOLE_ENV \
Signature · 1 line
1.7.0.4
PATCH v4 8/11 blackfin: bf60x: add rsi/sdh support
In reply to Sonic ZhangFrom: Sonic Zhang <[email protected]>
Add rsi/sdh support for bf60x.
---
Changes in v4:
- Fix checkpatch warning whitespace before semicolon
Changes in v3: None
Changes in v2:
- Fix checkpatch issues.
- Does't change funtion sdh_setup_data() to return void.
arch/blackfin/include/asm/mach-common/bits/sdh.h | 38 +++++++++++- drivers/mmc/bfin_sdh.c | 68 ++++++++++++++++----- 2 files changed, 88 insertions(+), 18 deletions(-)
arch/blackfin/include/asm/mach-common/bits/sdh.h +36 -2
@@ -12,18 +12,35 @@#define CMD_INT_E 0x100/* Command Interrupt */ #define CMD_PEND_E 0x200/* Command Pending */ #define CMD_E 0x400/* Command Enable */ +#ifdef RSI_BLKSZ +#define CMD_CRC_CHECK_D 0x800/* CRC Check is disabled */ +#define CMD_DATA0_BUSY 0x1000/* Check Busy State on DATA0 */ +#endif /* Bit masks for SDH_PWR_CTL */ +#ifndef RSI_BLKSZ #define PWR_ON 0x3/* Power On */ #define SD_CMD_OD 0x40/* Open Drain Output */ #define ROD_CTL 0x80/* Rod Control */ +#endif /* Bit masks for SDH_CLK_CTL */ #define CLKDIV 0xff/* MC_CLK Divisor */ #define CLK_E 0x100/* MC_CLK Bus Clock Enable */ #define PWR_SV_E 0x200/* Power Save Enable */ #define CLKDIV_BYPASS 0x400/* Bypass Divisor */ -#define WIDE_BUS 0x800/* Wide Bus Mode Enable */ +#define BUS_MODE_MASK 0x1800/* Bus Mode Mask */ +#define STD_BUS_1 0x000/* Standard Bus 1 bit mode */ +#define WIDE_BUS_4 0x800/* Wide Bus 4 bit mode */ +#define BYTE_BUS_8 0x1000/* Byte Bus 8 bit mode */ +#ifdef RSI_BLKSZ +#define CARD_TYPE_MASK 0xe000/* Card type mask */ +#define CARD_TYPE_OFFSET 13/* Card type offset */ +#define CARD_TYPE_SDIO 0 +#define CARD_TYPE_eMMC 1 +#define CARD_TYPE_SD 2 +#define CARD_TYPE_CEATA 3 +#endif /* Bit masks for SDH_RESP_CMD */ #define RESP_CMD 0x3f/* Response Command */
@@ -33,7 +50,13 @@#define DTX_DIR 0x2/* Data Transfer Direction */ #define DTX_MODE 0x4/* Data Transfer Mode */ #define DTX_DMA_E 0x8/* Data Transfer DMA Enable */ +#ifndef RSI_BLKSZ #define DTX_BLK_LGTH 0xf0/* Data Transfer Block Length */ +#else + +/* Bit masks for SDH_BLK_SIZE */ +#define DTX_BLK_LGTH 0x1fff/* Data Transfer Block Length */ +#endif /* Bit masks for SDH_STATUS */ #define CMD_CRC_FAIL 0x1/* CMD CRC Fail */
@@ -102,10 +125,13 @@/* Bit masks for SDH_E_STATUS */ #define SDIO_INT_DET 0x2/* SDIO Int Detected */ #define SD_CARD_DET 0x10/* SD Card Detect */ +#define SD_CARD_BUSYMODE 0x80000000/* Card is in Busy mode */ +#define SD_CARD_SLPMODE 0x40000000/* Card in Sleep Mode */ +#define SD_CARD_READY 0x00020000/* Card Ready */ /* Bit masks for SDH_E_MASK */ #define SDIO_MSK 0x2/* Mask SDIO Int Detected */ -#define SCD_MSK 0x40/* Mask Card Detect */ +#define SCD_MSK 0x10/* Mask Card Detect */ /* Bit masks for SDH_CFG */ #define CLKS_EN 0x1/* Clocks Enable */
@@ -114,7 +140,15 @@#define SD_RST 0x10/* SDMMC Reset */ #define PUP_SDDAT 0x20/* Pull-up SD_DAT */ #define PUP_SDDAT3 0x40/* Pull-up SD_DAT3 */ +#ifndef RSI_BLKSZ #define PD_SDDAT3 0x80/* Pull-down SD_DAT3 */ +#else +#define PWR_ON 0x600/* Power On */ +#define SD_CMD_OD 0x800/* Open Drain Output */ +#define BOOT_EN 0x1000/* Boot Enable */ +#define BOOT_MODE 0x2000/* Alternate Boot Mode */ +#define BOOT_ACK_EN 0x4000/* Boot ACK is expected */ +#endif /* Bit masks for SDH_RD_WAIT_EN */ #define RWR 0x1/* Read Wait Request */
drivers/mmc/bfin_sdh.c +52 -16
149 lines not on this page · raw message
Signature · 1 line
1.7.0.4
PATCH v4 9/11 blackfin: add bf6xx spi driver
In reply to Sonic ZhangFrom: Scott Jiang <[email protected]>
Spi driver for bf60x is different from old one, so implement a new driver for it.
---
Changes in v4: None
Changes in v3: None
Changes in v2:
- Fix checkpatch issues
.../blackfin/include/asm/mach-common/bits/spi6xx.h | 240 +++++++++++++++ drivers/spi/Makefile | 1 + drivers/spi/bfin_spi6xx.c | 308 ++++++++++++++++++++ 3 files changed, 549 insertions(+), 0 deletions(-) create mode 100644 arch/blackfin/include/asm/mach-common/bits/spi6xx.h create mode 100644 drivers/spi/bfin_spi6xx.c
arch/blackfin/include/asm/mach-common/bits/spi6xx.h new file +240 -0
@@ -0,0 +1,240 @@ +/* +* Analog Devices bfin_spi3 controller driver +* +* Copyright (c) 2011 Analog Devices Inc. +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +*/ + +#ifndef _SPI_CHANNEL_H_ +#define _SPI_CHANNEL_H_ + +#include <linux/types.h> + +/* SPI_CONTROL */ +#define SPI_CTL_EN 0x00000001/* Enable */ +#define SPI_CTL_MSTR 0x00000002/* Master/Slave */ +#define SPI_CTL_PSSE 0x00000004/* controls modf error in master mode */ +#define SPI_CTL_ODM 0x00000008/* Open Drain Mode */ +#define SPI_CTL_CPHA 0x00000010/* Clock Phase */ +#define SPI_CTL_CPOL 0x00000020/* Clock Polarity */ +#define SPI_CTL_ASSEL 0x00000040/* Slave Select Pin Control */ +#define SPI_CTL_SELST 0x00000080/* Slave Select Polarity in transfers */ +#define SPI_CTL_EMISO 0x00000100/*Enable MISO */ +#define SPI_CTL_SIZE 0x00000600/*Word Transfer Size */ +#define SPI_CTL_SIZE08 0x00000000/*SIZE: 8 bits */ +#define SPI_CTL_SIZE16 0x00000200/*SIZE: 16 bits */ +#define SPI_CTL_SIZE32 0x00000400/*SIZE: 32 bits */ +#define SPI_CTL_LSBF 0x00001000/*LSB First */ +#define SPI_CTL_FCEN 0x00002000/*Flow-Control Enable */ +#define SPI_CTL_FCCH 0x00004000/*Flow-Control Channel Selection */ +#define SPI_CTL_FCPL 0x00008000/*Flow-Control Polarity */ +#define SPI_CTL_FCWM 0x00030000/*Flow-Control Water-Mark */ +#define SPI_CTL_FIFO0 0x00000000/*FCWM: Tx empty or Rx Full */ +#define SPI_CTL_FIFO1 0x00010000/*FCWM: Tx empty or Rx full (>=75%) */ +#define SPI_CTL_FIFO2 0x00020000/*FCWM: Tx empty or Rx full (>=50%) */ +#define SPI_CTL_FMODE 0x00040000/*Fast-mode Enable */ +#define SPI_CTL_MIOM 0x00300000/*Multiple I/O Mode */ +#define SPI_CTL_MIO_DIS 0x00000000/*MIOM: Disable */ +#define SPI_CTL_MIO_DUAL 0x00100000/*MIOM: Enable DIOM (Dual I/O Mode) */ +#define SPI_CTL_MIO_QUAD 0x00200000/*MIOM: Enable QUAD (Quad SPI Mode) */ +#define SPI_CTL_SOSI 0x00400000/*Start on MOSI */ +/* SPI_RX_CONTROL */ +#define SPI_RXCTL_REN 0x00000001/*Receive Channel Enable */ +#define SPI_RXCTL_RTI 0x00000004/*Receive Transfer Initiate */ +#define SPI_RXCTL_RWCEN 0x00000008/*Receive Word Counter Enable */ +#define SPI_RXCTL_RDR 0x00000070/*Receive Data Request */ +#define SPI_RXCTL_RDR_DIS 0x00000000/*RDR: Disabled */ +#define SPI_RXCTL_RDR_NE 0x00000010/*RDR: RFIFO not empty */ +#define SPI_RXCTL_RDR_25 0x00000020/*RDR: RFIFO 25% full */ +#define SPI_RXCTL_RDR_50 0x00000030/*RDR: RFIFO 50% full */ +#define SPI_RXCTL_RDR_75 0x00000040/*RDR: RFIFO 75% full */ +#define SPI_RXCTL_RDR_FULL 0x00000050/*RDR: RFIFO full */ +#define SPI_RXCTL_RDO 0x00000100/*Receive Data Over-Run */ +#define SPI_RXCTL_RRWM 0x00003000/*FIFO Regular Water-Mark */ +#define SPI_RXCTL_RWM_0 0x00000000/*RRWM: RFIFO Empty */ +#define SPI_RXCTL_RWM_25 0x00001000/*RRWM: RFIFO 25% full */ +#define SPI_RXCTL_RWM_50 0x00002000/*RRWM: RFIFO 50% full */ +#define SPI_RXCTL_RWM_75 0x00003000/*RRWM: RFIFO 75% full */ +#define SPI_RXCTL_RUWM 0x00070000/*FIFO Urgent Water-Mark */ +#define SPI_RXCTL_UWM_DIS 0x00000000/*RUWM: Disabled */ +#define SPI_RXCTL_UWM_25 0x00010000/*RUWM: RFIFO 25% full */ +#define SPI_RXCTL_UWM_50 0x00020000/*RUWM: RFIFO 50% full */ +#define SPI_RXCTL_UWM_75 0x00030000/*RUWM: RFIFO 75% full */ +#define SPI_RXCTL_UWM_FULL 0x00040000/*RUWM: RFIFO full */ +/* SPI_TX_CONTROL */ +#define SPI_TXCTL_TEN 0x00000001/*Transmit Channel Enable */ +#define SPI_TXCTL_TTI 0x00000004/*Transmit Transfer Initiate */ +#define SPI_TXCTL_TWCEN 0x00000008/*Transmit Word Counter Enable */ +#define SPI_TXCTL_TDR 0x00000070/*Transmit Data Request */ +#define SPI_TXCTL_TDR_DIS 0x00000000/*TDR: Disabled */ +#define SPI_TXCTL_TDR_NF 0x00000010/*TDR: TFIFO not full */ +#define SPI_TXCTL_TDR_25 0x00000020/*TDR: TFIFO 25% empty */ +#define SPI_TXCTL_TDR_50 0x00000030/*TDR: TFIFO 50% empty */ +#define SPI_TXCTL_TDR_75 0x00000040/*TDR: TFIFO 75% empty */ +#define SPI_TXCTL_TDR_EMPTY 0x00000050/*TDR: TFIFO empty */ +#define SPI_TXCTL_TDU 0x00000100/*Transmit Data Under-Run */ +#define SPI_TXCTL_TRWM 0x00003000/*FIFO Regular Water-Mark */ +#define SPI_TXCTL_RWM_FULL 0x00000000/*TRWM: TFIFO full */ +#define SPI_TXCTL_RWM_25 0x00001000/*TRWM: TFIFO 25% empty */ +#define SPI_TXCTL_RWM_50 0x00002000/*TRWM: TFIFO 50% empty */ +#define SPI_TXCTL_RWM_75 0x00003000/*TRWM: TFIFO 75% empty */ +#define SPI_TXCTL_TUWM 0x00070000/*FIFO Urgent Water-Mark */ +#define SPI_TXCTL_UWM_DIS 0x00000000/*TUWM: Disabled */ +#define SPI_TXCTL_UWM_25 0x00010000/*TUWM: TFIFO 25% empty */ +#define SPI_TXCTL_UWM_50 0x00020000/*TUWM: TFIFO 50% empty */ +#define SPI_TXCTL_UWM_75 0x00030000/*TUWM: TFIFO 75% empty */ +#define SPI_TXCTL_UWM_EMPTY 0x00040000/*TUWM: TFIFO empty */ +/* SPI_CLOCK */ +#define SPI_CLK_BAUD 0x0000FFFF/*Baud Rate */ +/* SPI_DELAY */ +#define SPI_DLY_STOP 0x000000FF/*Transfer delay time */ +#define SPI_DLY_LEADX 0x00000100/*Extended (1 SCK) LEAD Control */ +#define SPI_DLY_LAGX 0x00000200/*Extended (1 SCK) LAG control */ +/* SPI_SSEL */ +#define SPI_SLVSEL_SSE1 0x00000002/*SPISSEL1 Enable */ +#define SPI_SLVSEL_SSE2 0x00000004/*SPISSEL2 Enable */ +#define SPI_SLVSEL_SSE3 0x00000008/*SPISSEL3 Enable */ +#define SPI_SLVSEL_SSE4 0x00000010/*SPISSEL4 Enable */ +#define SPI_SLVSEL_SSE5 0x00000020/*SPISSEL5 Enable */ +#define SPI_SLVSEL_SSE6 0x00000040/*SPISSEL6 Enable */ +#define SPI_SLVSEL_SSE7 0x00000080/*SPISSEL7 Enable */ +#define SPI_SLVSEL_SSEL1 0x00000200/*SPISSEL1 Value */ +#define SPI_SLVSEL_SSEL2 0x00000400/*SPISSEL2 Value */ +#define SPI_SLVSEL_SSEL3 0x00000800/*SPISSEL3 Value */ +#define SPI_SLVSEL_SSEL4 0x00001000/*SPISSEL4 Value */ +#define SPI_SLVSEL_SSEL5 0x00002000/*SPISSEL5 Value */ +#define SPI_SLVSEL_SSEL6 0x00004000/*SPISSEL6 Value */ +#define SPI_SLVSEL_SSEL7 0x00008000/*SPISSEL7 Value */ +/* SPI_RWC */ +#define SPI_RWC_VALUE 0x0000FFFF/*Received Word-Count */ +/* SPI_RWCR */ +#define SPI_RWCR_VALUE 0x0000FFFF/*Received Word-Count Reload */ +/* SPI_TWC */ +#define SPI_TWC_VALUE 0x0000FFFF/*Transmitted Word-Count */ +/* SPI_TWCR */ +#define SPI_TWCR_VALUE 0x0000FFFF/*Transmitted Word-Count Reload */ +/* SPI_IMASK */ +#define SPI_IMSK_RUWM 0x00000002/*Receive Water-Mark Interrupt Mask */ +#define SPI_IMSK_TUWM 0x00000004/*Transmit Water-Mark Interrupt Mask */ +#define SPI_IMSK_ROM 0x00000010/*Receive Over-Run Interrupt Mask */ +#define SPI_IMSK_TUM 0x00000020/*Transmit Under-Run Interrupt Mask */ +#define SPI_IMSK_TCM 0x00000040/*Transmit Collision Interrupt Mask */ +#define SPI_IMSK_MFM 0x00000080/*Mode Fault Interrupt Mask */ +#define SPI_IMSK_RSM 0x00000100/*Receive Start Interrupt Mask */ +#define SPI_IMSK_TSM 0x00000200/*Transmit Start Interrupt Mask */ +#define SPI_IMSK_RFM 0x00000400/*Receive Finish Interrupt Mask */ +#define SPI_IMSK_TFM 0x00000800/*Transmit Finish Interrupt Mask */ +/* SPI_IMASKCL */ +#define SPI_IMSK_CLR_RUW 0x00000002/*Receive Water-Mark Interrupt Mask */ +#define SPI_IMSK_CLR_TUWM 0x00000004/*Transmit Water-Mark Interrupt Mask */ +#define SPI_IMSK_CLR_ROM 0x00000010/*Receive Over-Run Interrupt Mask */ +#define SPI_IMSK_CLR_TUM 0x00000020/*Transmit Under-Run Interrupt Mask */ +#define SPI_IMSK_CLR_TCM 0x00000040/*Transmit Collision Interrupt Mask */ +#define SPI_IMSK_CLR_MFM 0x00000080/*Mode Fault Interrupt Mask */ +#define SPI_IMSK_CLR_RSM 0x00000100/*Receive Start Interrupt Mask */ +#define SPI_IMSK_CLR_TSM 0x00000200/*Transmit Start Interrupt Mask */ +#define SPI_IMSK_CLR_RFM 0x00000400/*Receive Finish Interrupt Mask */ +#define SPI_IMSK_CLR_TFM 0x00000800/*Transmit Finish Interrupt Mask */ +/* SPI_IMASKST */ +#define SPI_IMSK_SET_RUWM 0x00000002/*Receive Water-Mark Interrupt Mask */ +#define SPI_IMSK_SET_TUWM 0x00000004/*Transmit Water-Mark Interrupt Mask */ +#define SPI_IMSK_SET_ROM 0x00000010/*Receive Over-Run Interrupt Mask */ +#define SPI_IMSK_SET_TUM 0x00000020/*Transmit Under-Run Interrupt Mask */ +#define SPI_IMSK_SET_TCM 0x00000040/*Transmit Collision Interrupt Mask */ +#define SPI_IMSK_SET_MFM 0x00000080/*Mode Fault Interrupt Mask */ +#define SPI_IMSK_SET_RSM 0x00000100/*Receive Start Interrupt Mask */ +#define SPI_IMSK_SET_TSM 0x00000200/*Transmit Start Interrupt Mask */ +#define SPI_IMSK_SET_RFM 0x00000400/*Receive Finish Interrupt Mask */ +#define SPI_IMSK_SET_TFM 0x00000800/*Transmit Finish Interrupt Mask */ +/* SPI_STATUS */ +#define SPI_STAT_SPIF 0x00000001/*SPI Finished */ +#define SPI_STAT_RUWM 0x00000002/*Receive Water-Mark Breached */ +#define SPI_STAT_TUWM 0x00000004/*Transmit Water-Mark Breached */ +#define SPI_STAT_ROE 0x00000010/*Receive Over-Run Indication */ +#define SPI_STAT_TUE 0x00000020/*Transmit Under-Run Indication */ +#define SPI_STAT_TCE 0x00000040/*Transmit Collision Indication */ +#define SPI_STAT_MODF 0x00000080/*Mode Fault Indication */ +#define SPI_STAT_RS 0x00000100/*Receive Start Indication */ +#define SPI_STAT_TS 0x00000200/*Transmit Start Indication */ +#define SPI_STAT_RF 0x00000400/*Receive Finish Indication */ +#define SPI_STAT_TF 0x00000800/*Transmit Finish Indication */ +#define SPI_STAT_RFS 0x00007000/*SPI_RFIFO status */ +#define SPI_STAT_RFIFO_EMPTY 0x00000000/*RFS: RFIFO Empty */ +#define SPI_STAT_RFIFO_25 0x00001000/*RFS: RFIFO 25% Full */ +#define SPI_STAT_RFIFO_50 0x00002000/*RFS: RFIFO 50% Full */ +#define SPI_STAT_RFIFO_75 0x00003000/*RFS: RFIFO 75% Full */ +#define SPI_STAT_RFIFO_FULL 0x00004000/*RFS: RFIFO Full */ +#define SPI_STAT_TFS 0x00070000/*SPI_TFIFO status */ +#define SPI_STAT_TFIFO_FULL 0x00000000/*TFS: TFIFO full */ +#define SPI_STAT_TFIFO_25 0x00010000/*TFS: TFIFO 25% empty */ +#define SPI_STAT_TFIFO_50 0x00020000/*TFS: TFIFO 50% empty */ +#define SPI_STAT_TFIFO_75 0x00030000/*TFS: TFIFO 75% empty */ +#define SPI_STAT_TFIFO_EMPTY 0x00040000/*TFS: TFIFO empty */ +#define SPI_STAT_FCS 0x00100000/*Flow-Control Stall Indication */ +#define SPI_STAT_RFE 0x00400000/*SPI_RFIFO Empty */ +#define SPI_STAT_TFF 0x00800000/*SPI_TFIFO Full */ +/* SPI_ILAT */ +#define SPI_ILAT_RUWMI 0x00000002/*Receive Water Mark Interrupt */ +#define SPI_ILAT_TUWMI 0x00000004/*Transmit Water Mark Interrupt */ +#define SPI_ILAT_ROI 0x00000010/*Receive Over-Run Indication */ +#define SPI_ILAT_TUI 0x00000020/*Transmit Under-Run Indication */ +#define SPI_ILAT_TCI 0x00000040/*Transmit Collision Indication */ +#define SPI_ILAT_MFI 0x00000080/*Mode Fault Indication */ +#define SPI_ILAT_RSI 0x00000100/*Receive Start Indication */ +#define SPI_ILAT_TSI 0x00000200/*Transmit Start Indication */ +#define SPI_ILAT_RFI 0x00000400/*Receive Finish Indication */ +#define SPI_ILAT_TFI 0x00000800/*Transmit Finish Indication */ +/* SPI_ILATCL */ +#define SPI_ILAT_CLR_RUWMI 0x00000002/*Receive Water Mark Interrupt */ +#define SPI_ILAT_CLR_TUWMI 0x00000004/*Transmit Water Mark Interrupt */ +#define SPI_ILAT_CLR_ROI 0x00000010/*Receive Over-Run Indication */ +#define SPI_ILAT_CLR_TUI 0x00000020/*Transmit Under-Run Indication */ +#define SPI_ILAT_CLR_TCI 0x00000040/*Transmit Collision Indication */ +#define SPI_ILAT_CLR_MFI 0x00000080/*Mode Fault Indication */ +#define SPI_ILAT_CLR_RSI 0x00000100/*Receive Start Indication */ +#define SPI_ILAT_CLR_TSI 0x00000200/*Transmit Start Indication */ +#define SPI_ILAT_CLR_RFI 0x00000400/*Receive Finish Indication */ +#define SPI_ILAT_CLR_TFI 0x00000800/*Transmit Finish Indication */ + +/* +* bfin spi3 registers layout +*/ +struct bfin_spi_regs { +u32 revid; +u32 control; +u32 rx_control; +u32 tx_control; +u32 clock; +u32 delay; +u32 ssel; +u32 rwc; +u32 rwcr; +u32 twc; +u32 twcr; +u32 reserved0; +u32 emask; +u32 emaskcl; +u32 emaskst; +u32 reserved1; +u32 status; +u32 elat; +u32 elatcl; +u32 reserved2; +u32 rfifo; +u32 reserved3; +u32 tfifo; +}; + +#endif /* _SPI_CHANNEL_H_ */
drivers/spi/Makefile +1 -0
@@ -31,6 +31,7 @@ COBJS-$(CONFIG_ARMADA100_SPI) += armada100_spi.o COBJS-$(CONFIG_ATMEL_DATAFLASH_SPI) += atmel_dataflash_spi.o COBJS-$(CONFIG_ATMEL_SPI) += atmel_spi.o COBJS-$(CONFIG_BFIN_SPI) += bfin_spi.o +COBJS-$(CONFIG_BFIN_SPI6XX) += bfin_spi6xx.o COBJS-$(CONFIG_CF_SPI) += cf_spi.o COBJS-$(CONFIG_CF_QSPI) += cf_qspi.o COBJS-$(CONFIG_DAVINCI_SPI) += davinci_spi.o
drivers/spi/bfin_spi6xx.c new file +308 -0
308 lines not on this page · raw message
Signature · 1 line
1.7.0.4
PATCH v4 10/11 blackfin: bf60x: add hw watchdog support
In reply to Sonic ZhangFrom: Bob Liu <[email protected]>
---
Changes in v4: None
Changes in v3: None
Changes in v2: None
arch/blackfin/cpu/initcode.c | 13 +++++++++++++ arch/blackfin/cpu/start.S | 2 ++ include/configs/bf609-ezkit.h | 1 + 3 files changed, 16 insertions(+), 0 deletions(-)
arch/blackfin/cpu/initcode.c +13 -0
@@ -461,8 +461,21 @@ program_early_devices(ADI_BOOT_DATA *bs, uint *sdivB, uint *divB, uint *vcoB)*/ if (CONFIG_BFIN_BOOT_MODE !=BFIN_BOOT_BYPASS ) {serial_putc ('e' ); +#ifdef __ADSPBF60x__ +bfin_write_SEC_GCTL (0x2 ); +SSYNC (); +bfin_write_SEC_FCTL (0xc1 ); +bfin_write_SEC_SCTL (2 ,bfin_read_SEC_SCTL (2 ) |0x6 ); + +bfin_write_SEC_CCTL (0x2 ); +SSYNC (); +bfin_write_SEC_GCTL (0x1 ); +bfin_write_SEC_CCTL (0x1 ); +#endif bfin_write_WDOG_CNT (MSEC_TO_SCLK (CONFIG_HW_WATCHDOG_TIMEOUT_INITCODE )); +#if CONFIG_BFIN_BOOT_MODE !=BFIN_BOOT_UART bfin_write_WDOG_CTL (0 ); +#endif serial_putc ('f' ); }#endif
arch/blackfin/cpu/start.S +2 -0
@@ -65,6 +65,7 @@ ENTRY(_start) p5.h = HI(COREMMR_BASE); #ifdef CONFIG_HW_WATCHDOG +#ifndef __ADSPBF60x__ # ifndef CONFIG_HW_WATCHDOG_TIMEOUT_START # define CONFIG_HW_WATCHDOG_TIMEOUT_START 5000 # endif
@@ -78,6 +79,7 @@ ENTRY(_start) /* fire up the watchdog - R0.L above needs to be 0x0000 */ W[p4 + (WDOG_CTL - SYSMMR_BASE)] = r0; #endif +#endif /* Turn on the serial for debugging the init process */ serial_early_init
include/configs/bf609-ezkit.h +1 -0
@@ -63,6 +63,7 @@#define CONFIG_SYS_MONITOR_LEN (768 * 1024)#define CONFIG_SYS_MALLOC_LEN (512 * 1024) +#define CONFIG_HW_WATCHDOG /* * Network Settings */
Signature · 1 line
1.7.0.4
PATCH v4 11/11 blackfin: bf60x: add resume from hibernate
In reply to Sonic ZhangFrom: Steven Miao <[email protected]>
Add Bf60x resume from hibernate support
---
Changes in v4: None
Changes in v3: None
Changes in v2:
- Fix checkpatch issues
arch/blackfin/cpu/initcode.c | 46 ++++++++++++++++++++++++++++++++++++++++++ 1 files changed, 46 insertions(+), 0 deletions(-)
arch/blackfin/cpu/initcode.c +46 -0
@@ -509,6 +509,11 @@ maybe_self_refresh(ADI_BOOT_DATA *bs)return false;#ifdef __ADSPBF60x__ +/* resume from hibernate, return false let ddr initialize */ +if ((bfin_read32 (DPM0_STAT ) &0xF0 ) ==0x50 ) { +serial_putc ('b' ); +return false; + }#else /* __ADSPBF60x__ */
@@ -827,6 +832,7 @@ program_memory_controller(ADI_BOOT_DATA *bs, bool put_into_srfs)while (!(bfin_read_DMC0_STAT () &DLLCALDONE ))continue ;serial_putc ('!' ); +#else /* __ADSPBF60x__ */ /* Program the external memory controller before we come out of
@@ -894,7 +900,46 @@ check_hibernation(ADI_BOOT_DATA *bs, u16 vr_ctl, bool put_into_srfs)return ;serial_putc ('b' ); +#ifdef __ADSPBF60x__ +if (bfin_read32 (DPM0_RESTORE0 ) !=0 ) { +uint32_t reg =bfin_read_DMC0_CTL (); + reg &= ~0x8 ; +bfin_write_DMC0_CTL (reg); + +while ((bfin_read_DMC0_STAT () &0x8 )) +continue ; +while (!(bfin_read_DMC0_STAT () &0x1 )) +continue ; +serial_putc ('z' ); +uint32_t *hibernate_magic =bfin_read32 (DPM0_RESTORE4 ); +SSYNC ();/* make sure memory controller is done */ +if (hibernate_magic[0 ] ==0xDEADBEEF ) { +serial_putc ('c' ); +SSYNC (); +bfin_write_EVT15 (hibernate_magic[1 ]); +bfin_write_IMASK (EVT_IVG15 ); + __asm__ __volatile__ ( +/* load reti early to avoid anomaly 281 */ +"reti = %2;" +/* clear hibernate magic */ +"[%0] = %1;" +/* load stack pointer */ +"SP = [%0 + 8];" +/* lower ourselves from reset ivg to ivg15 */ +"raise 15;" +"nop;nop;nop;" +"rti;" + : + :"p" (hibernate_magic), +"d" (0x2000 /* jump.s 0 */ ), +"d" (0xffa00000 ) + ); + } + + + } +#else /* Are we coming out of hibernate (suspend to memory) ? * The memory layout is: * 0x0: hibernate magic for anomaly 307 (0xDEADBEEF)
@@ -927,6 +972,7 @@ check_hibernation(ADI_BOOT_DATA *bs, u16 vr_ctl, bool put_into_srfs) }serial_putc ('d' ); } +#endif serial_putc ('e' ); }
Signature · 1 line
1.7.0.4
v4 cover Add BF60x processor support to Blackfin architecture.
In reply to Sonic ZhangQuoted 7 lines · Sonic Zhang
From: Sonic Zhang <[email protected]>
ADSP-BF60x is the new generation Blackfin?? dual-core processor announced by Analog Devices in late March, 2012. This patch set adds BF60x processor support to Das U-Boot Blackfin architecture.
Quoted 8 lines
For more information, see http://blackfin.uclinux.org .
Changes in v4:
- Remove last blank line ininitcode.c.
- Fix all checkpatch issues except for cpu name bf609-0.0. It is use as the link flags and is not an error.
- Remove the values for variables in bf609 config headers whose values are useless.
- Fix checkpatch warning whitespace before semicolon
This all looks fine. If no one else comments soon, feel free to make up your first pull request.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130228/34ceda3d/attachment.pgp>
v4 cover Add BF60x processor support to Blackfin architecture.
Hi Tom,
Quoted 18 lines · Tom Rini
Quoted 7 lines · Sonic Zhang
From: Sonic Zhang <[email protected]>
ADSP-BF60x is the new generation Blackfin?? dual-core processor announced by Analog Devices in late March, 2012. This patch set adds BF60x processor support to Das U-Boot Blackfin architecture.
Quoted 8 lines
For more information, see http://blackfin.uclinux.org .
Changes in v4:
- Remove last blank line ininitcode.c.
- Fix all checkpatch issues except for cpu name bf609-0.0. It is use as the link flags and is not an error.
- Remove the values for variables in bf609 config headers whose values are useless.
- Fix checkpatch warning whitespace before semicolon
Quoted 3 lines
This all looks fine. If no one else comments soon, feel free to make up your first pull request.
Thank you for your help. Because the Merge Window for the next release (v2013.04) was closed on Feb 09, should I make up the pull request after the (v2013.04) release on Apr. 15?
Regards,
Sonic
v4 cover Add BF60x processor support to Blackfin architecture.
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 21 lines · Sonic Zhang
Hi Tom,
Quoted 18 lines · Tom Rini
Quoted 15 lines · Sonic Zhang
From: Sonic Zhang <[email protected]>
ADSP-BF60x is the new generation Blackfin?? dual-core processor announced by Analog Devices in late March, 2012. This patch set adds BF60x processor support to Das U-Boot Blackfin architecture.
For more information, see http://blackfin.uclinux.org .
Changes in v4: - Remove last blank line in
initcode.c. - Fix all checkpatch issues except for cpu name bf609-0.0. It is use as the link flags and is not an error. - Remove the values for variables in bf609 config headers whose values are useless. - Fix checkpatch warning whitespace before semicolon
Quoted 7 lines
Quoted 3 lines
This all looks fine. If no one else comments soon, feel free to make up your first pull request.
Thank you for your help. Because the Merge Window for the next release (v2013.04) was closed on Feb 09, should I make up the pull request after the (v2013.04) release on Apr. 15?
The merge window is for v1 of patches to be posted (unlike the kernel), and I see v1 was Feb 07, so this is fine for the v2013.04 release.
- --
Tom
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/
iQIcBAEBAgAGBQJRMLgiAAoJENk4IS6UOR1WYdIQAK6GxbyOksTxozrGI4/QHNc+ +94v4D2tw0PSaNPbaVodR5eL7U9YCIPIXStDvu56DNauF+UW8ZTA2NinJaL+NP92 XfkfGADBSXB9DK7/ZYdgxeF/MA0cF9mQuO56c6ZVXkBBAXrsNc+NdDuacQC77GdE 8h4kofuVk32ycPW3jZWXQL2esNx5wiux0sEcQ7CRyDS9KGjRuPUXF7C8JBRSon7Q O9cuqxiX/Hc224xNu4w7KyIFqu3MNnQi7DTSXGwxT8mqXYJTgqpWqDBwisJX+oKP 7P9Tsd2f3ZcZLuLYC4LNstuN3si/6VPOfKaUI52+IJG+v1ZtHeKbZWQ0uSwe3Vfx cKXmmyzNcOxb28Zk7y5OyISi/W9gld4Sa/wiUKFitD2Y7/ZMdX8I63oVi4kWgwyW ox9UH+mUFj92edjyPflgRmMOFrGnNEBpJEKRJBWGztKCRR66QuSlOpQ+PebLuiPE NYDuAh1w0PsgR1AZFHEQh+bt9q/GZn93mKZD6bbdIGcSn84g4GoenlxA6SPZ7Pwg aXZ8LeU5cf3A8R4a6hnew87W4JgZ31mJ0u2sT9R2nv3m8frYb+UPCdhBItDV2oM7 t2PfAQPneZDkl4XcTi2QiQf+WtlMltJpi4yXRfrv/UU8v1ebW8KU1+acXieOMaT8 rmYIEiORyrcH/Hb/wH+4
=BLr9
-----END PGP SIGNATURE-----