input,serio: support for GRLIB APBPS2 PS/2 Keyboard/Mouse
Subsystems (3)
PATCH v2 1/1 input,serio: support for GRLIB APBPS2 PS/2 Keyboard/Mouse
APBPS2 is a PS/2 core part of GRLIB found in SPARC32/LEON products.
--- .../bindings/input/ps2keyb-mouse-apbps2.txt | 20 ++ drivers/input/serio/Kconfig | 10 + drivers/input/serio/Makefile | 1 + drivers/input/serio/apbps2.c | 228 ++++++++++++++++++++ 4 files changed, 259 insertions(+), 0 deletions(-) create mode 100644 Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt create mode 100644 drivers/input/serio/apbps2.c
Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt new file +20 -0
@@ -0,0 +1,20 @@ +Aeroflex Gaisler APBPS2 PS/2 Core, supporting Keyboard or Mouse. + +The APBPS2 PS/2 core is available in the GRLIB VHDL IP core library. + +Note: In the ordinary environment for the APBPS2 core, a LEON SPARC system, +these properties are built from information in the AMBA plug&play and from +bootloader settings. + +Required properties: + +- name : Should be "GAISLER_APBPS2" or "01_060" +- reg : Address and length of the register set for the device +- interrupts : Interrupt numbers for this device + +Optional properties: +- keyboard : if present it indicates that a keyboard is connected, if not + present the driver will assume that a mouse is connected instead + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdf
drivers/input/serio/Kconfig +10 -0
@@ -244,4 +244,14 @@ config SERIO_ARC_PS2 To compile this driver as a module, choose M here; the module will be called arc_ps2. +config SERIO_APBPS2 + tristate "GRLIB APBPS2 PS/2 keyboard/mouse controller" + depends on OF + help + Say Y here if you want support for GRLIB APBPS2 peripherals used + to connect to PS/2 keyboard and/or mouse. + + To compile this driver as a module, choose M here: the module will + be called apbps2. + endif
drivers/input/serio/Makefile +1 -0
@@ -26,3 +26,4 @@ obj-$(CONFIG_SERIO_AMS_DELTA) += ams_delta_serio.o obj-$(CONFIG_SERIO_XILINX_XPS_PS2) += xilinx_ps2.o obj-$(CONFIG_SERIO_ALTERA_PS2) += altera_ps2.o obj-$(CONFIG_SERIO_ARC_PS2) += arc_ps2.o +obj-$(CONFIG_SERIO_APBPS2) += apbps2.o
drivers/input/serio/apbps2.c new file +228 -0
228 lines not on this page · raw message
Signature · 1 line
1.7.0.4
Dmitry Torokhov
maintainerHi Danilel,
Quoted 2 lines · Daniel Hellstrom
APBPS2 is a PS/2 core part of GRLIB found in SPARC32/LEON products.
Thank you for making the changes, I have a couple more comments.
Quoted 71 lines
Signed-off-by Daniel Hellstrom <[email protected]>--- .../bindings/input/ps2keyb-mouse-apbps2.txt | 20 ++ drivers/input/serio/Kconfig | 10 + drivers/input/serio/Makefile | 1 + drivers/input/serio/apbps2.c | 228 ++++++++++++++++++++ 4 files changed, 259 insertions(+), 0 deletions(-) create mode 100644 Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt create mode 100644 drivers/input/serio/apbps2.cDocumentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt new file +20
-0@@ -0,0 +1,20 @@ +Aeroflex Gaisler APBPS2 PS/2 Core, supporting Keyboard or Mouse. + +The APBPS2 PS/2 core is available in the GRLIB VHDL IP core library. + +Note: In the ordinary environment for the APBPS2 core, a LEON SPARC system, +these properties are built from information in the AMBA plug&play and from +bootloader settings. + +Required properties: + +- name : Should be "GAISLER_APBPS2" or "01_060" +- reg : Address and length of the register set for the device +- interrupts : Interrupt numbers for this device + +Optional properties: +- keyboard : if present it indicates that a keyboard is connected, if not + present the driver will assume that a mouse is connected instead + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdfdrivers/input/serio/Kconfig +10
-0@@ -244,4 +244,14 @@ config SERIO_ARC_PS2 To compile this driver as a module, choose M here; the module will be called arc_ps2. +config SERIO_APBPS2 + tristate "GRLIB APBPS2 PS/2 keyboard/mouse controller" + depends on OF + help + Say Y here if you want support for GRLIB APBPS2 peripherals used + to connect to PS/2 keyboard and/or mouse. + + To compile this driver as a module, choose M here: the module will + be called apbps2. + endifdrivers/input/serio/Makefile +1
-0@@ -26,3 +26,4 @@ obj-$(CONFIG_SERIO_AMS_DELTA) += ams_delta_serio.o obj-$(CONFIG_SERIO_XILINX_XPS_PS2) += xilinx_ps2.o obj-$(CONFIG_SERIO_ALTERA_PS2) += altera_ps2.o obj-$(CONFIG_SERIO_ARC_PS2) += arc_ps2.o +obj-$(CONFIG_SERIO_APBPS2) += apbps2.odrivers/input/serio/apbps2.c new file +0
-0
drivers/input/serio/apbps2.c line 2
Quoted 2 lines
drivers/input/serio/apbps2.c new file +2
-0@@ -0,0 +1,228 @@ +/* +* linux/drivers/input/serio/apbps2.c
Please drop the file name - this way if we ever need to rename/move file it will not get in the way.
Quoted 142 lines
drivers/input/serio/apbps2.c new file +142
-0+* +* Copyright (C) 2013 Aeroflex Gaisler +* +* This driver supports the APBPS2 PS/2 core available in the GRLIB +* VHDL IP core library. +* +* Full documentation of the APBPS2 core can be found here: +* http://www.gaisler.com/products/grlib/grip.pdf +* +* See "Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt" for +* information on open firmware properties. +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* Contributors: Daniel Hellstrom <[email protected]> +*/ +#include <linux/platform_device.h> +#include <linux/of_device.h> +#include <linux/module.h> +#include <linux/serio.h> +#include <linux/errno.h> +#include <linux/interrupt.h> +#include <linux/of_irq.h> +#include <linux/device.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/string.h> +#include <linux/kernel.h> +#include <linux/io.h> + +struct apbps2_regs { +u32 __iomem data;/* 0x00 */ +u32 __iomem status;/* 0x04 */ +u32 __iomem ctrl;/* 0x08 */ +u32 __iomem reload;/* 0x0c */ +}; + +#define APBPS2_STATUS_DR (1<<0) +#define APBPS2_STATUS_PE (1<<1) +#define APBPS2_STATUS_FE (1<<2) +#define APBPS2_STATUS_KI (1<<3) +#define APBPS2_STATUS_RF (1<<4) +#define APBPS2_STATUS_TF (1<<5) +#define APBPS2_STATUS_TCNT (0x1f<<22) +#define APBPS2_STATUS_RCNT (0x1f<<27) + +#define APBPS2_CTRL_RE (1<<0) +#define APBPS2_CTRL_TE (1<<1) +#define APBPS2_CTRL_RI (1<<2) +#define APBPS2_CTRL_TI (1<<3) + +struct apbps2_priv { +struct serio *io; +struct apbps2_regs *regs; +}; + +static irqreturn_t apbps2_isr (int irq,void *dev_id) +{ +struct apbps2_priv *priv = dev_id; +unsigned long status, data, rxflags; +irqreturn_t ret =IRQ_NONE ; + +while ((status =ioread32be (&priv->regs->status)) &APBPS2_STATUS_DR ) { + data =ioread32be (&priv->regs->data); + rxflags = (status &APBPS2_STATUS_PE ) ?SERIO_PARITY :0 ; + rxflags |= (status &APBPS2_STATUS_PE ) ?SERIO_FRAME :0 ; + +/* clear error bits? */ +if (rxflags) +iowrite32be (status, &priv->regs->status); + +serio_interrupt (priv->io, data, rxflags); + + ret =IRQ_HANDLED ; + } + +return ret; +} + +static int apbps2_write (struct serio *io,unsigned char val) +{ +struct apbps2_priv *priv = io->port_data; +unsigned int tleft =10000 ;/* timeout in 100ms */ + +/* delay until PS/2 controller has room for more chars */ +while ((ioread32be (&priv->regs->status) &APBPS2_STATUS_TF ) && tleft--) +udelay (10 ); + +if ((ioread32be (&priv->regs->status) &APBPS2_STATUS_TF ) ==0 ) { +iowrite32be (val, &priv->regs->data); + +iowrite32be (APBPS2_CTRL_RE |APBPS2_CTRL_RI |APBPS2_CTRL_TE , + &priv->regs->ctrl); +return 0 ; + } + +return -ETIMEDOUT ; +} + +static int apbps2_open (struct serio *io) +{ +struct apbps2_priv *priv = io->port_data; +int limit; +unsigned long tmp; + +/* clear error flags */ +iowrite32be (0 , &priv->regs->status); + +/* Clear old data if available (unlikely) */ + limit =1024 ; +while ((ioread32be (&priv->regs->status) &APBPS2_STATUS_DR ) && --limit) + tmp =ioread32be (&priv->regs->data); + +/* Enable reciever and it's interrupt */ +iowrite32be (APBPS2_CTRL_RE |APBPS2_CTRL_RI , &priv->regs->ctrl); + +return 0 ; +} + +static void apbps2_close (struct serio *io) +{ +struct apbps2_priv *priv = io->port_data; + +/* stop interrupts at PS/2 HW level */ +iowrite32be (0 , &priv->regs->ctrl); +} + +/* Initialize one APBPS2 PS/2 core */ +static int apbps2_of_probe (struct platform_device *ofdev) +{ +struct apbps2_priv *priv; +int irq, err; +u32 freq_hz; +struct resource *res; + + priv =devm_kzalloc (&ofdev->dev,sizeof (*priv),GFP_KERNEL ); +if (!priv) { +dev_err (&ofdev->dev,"memory allocation failed\n" ); +return -ENOMEM ;
drivers/input/serio/apbps2.c line 154
Quoted 10 lines
drivers/input/serio/apbps2.c new file +10
-0+ } +platform_set_drvdata (ofdev, priv); + +/* Find Device Address */ + res =platform_get_resource (ofdev,IORESOURCE_MEM ,0 ); + priv->regs =devm_request_and_ioremap (&ofdev->dev, res); +if (!priv->regs) { +dev_err (&ofdev->dev,"io-regs mapping failed\n" ); +return -EADDRNOTAVAIL ; + }
Could you please make sure you shut off IRQs in chip here as well, like yo udo in apbps2_close(), before requesting IRQ?
Quoted 17 lines
drivers/input/serio/apbps2.c new file +17
-0+ +/* IRQ */ + irq =irq_of_parse_and_map (ofdev->dev.of_node,0 ); + err =devm_request_irq (&ofdev->dev, irq, apbps2_isr,IRQF_SHARED , +"apbps2" , priv); +if (err) { +dev_err (&ofdev->dev,"request IRQ%d failed\n" , irq); +return err; + } + +/* Get core frequency */ +if (of_property_read_u32 (ofdev->dev.of_node,"freq" , &freq_hz)) { +dev_err (&ofdev->dev,"unable to get core frequency\n" ); +return -EINVAL ; + } + + priv->io =kzalloc (sizeof (struct serio ),GFP_KERNEL );
drivers/input/serio/apbps2.c line 181
Quoted 10 lines
drivers/input/serio/apbps2.c new file +10
-0+if (!priv->io) +return -ENOMEM ; + + priv->io->id.type =SERIO_8042 ; + priv->io->open = apbps2_open; + priv->io->close = apbps2_close; + priv->io->write = apbps2_write; + priv->io->port_data = priv; +strlcpy (priv->io->name,"APBPS2 PS/2" ,sizeof (priv->io->name)); +strlcpy (priv->io->phys,"apbps2" ,sizeof (priv->io->phys));
Phys is supposed to be unique within the system, you may want to use a counter or some other identifying data for particular port. Or is there just one PS/2 port in the system?
Quoted 50 lines
drivers/input/serio/apbps2.c new file +47
-0+ +dev_info (&ofdev->dev,"irq = %d, base = 0x%p\n" , irq, priv->regs); + +/* Set reload register to system freq in kHz/10 */ +iowrite32be (freq_hz /10000 , &priv->regs->reload); + +serio_register_port (priv->io); + +return 0 ; +} + +static int apbps2_of_remove (struct platform_device *of_dev) +{ +struct apbps2_priv *priv =platform_get_drvdata (of_dev); + +serio_unregister_port (priv->io); + +return 0 ; +} + +static struct of_device_id apbps2_of_match[] = { + { + .name ="GAISLER_APBPS2" , + }, + { + .name ="01_060" , + }, + {}, +}; + +MODULE_DEVICE_TABLE (of, apbps2_of_match); + +static struct platform_driver apbps2_of_driver = { + .driver = { + .name ="grlib-apbps2" , + .owner =THIS_MODULE , + .of_match_table = apbps2_of_match, + }, + .probe = apbps2_of_probe, + .remove = apbps2_of_remove, +}; + +module_platform_driver (apbps2_of_driver); + +MODULE_AUTHOR ("Aeroflex Gaisler AB." ); +MODULE_DESCRIPTION ("GRLIB APBPS2 PS/2 serial I/O" ); +MODULE_LICENSE ("GPL" );Signature · 1 line
1.7.0.4
Thanks.
Signature · 1 line
Dmitry
Hi Dmitry,
Quoted 6 lines · Dmitry Torokhov
Hi Danilel,
Quoted 2 lines · Daniel Hellstrom
APBPS2 is a PS/2 core part of GRLIB found in SPARC32/LEON products.
Thank you for making the changes, I have a couple more comments.
Thank you for your comments and your time, I appreciate it.
Quoted 66 lines
Quoted 66 lines
Signed-off-by Daniel Hellstrom <[email protected]>--- .../bindings/input/ps2keyb-mouse-apbps2.txt | 20 ++ drivers/input/serio/Kconfig | 10 + drivers/input/serio/Makefile | 1 + drivers/input/serio/apbps2.c | 228 ++++++++++++++++++++ 4 files changed, 259 insertions(+), 0 deletions(-)create mode 100644
Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txtcreate mode 100644drivers/input/serio/apbps2.cDocumentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt new file +20
-0@@ -0,0 +1,20 @@ +Aeroflex Gaisler APBPS2 PS/2 Core, supporting Keyboard or Mouse. + +The APBPS2 PS/2 core is available in the GRLIB VHDL IP core library. + +Note: In the ordinary environment for the APBPS2 core, a LEON SPARC system, +these properties are built from information in the AMBA plug&play and from +bootloader settings. + +Required properties: + +- name : Should be "GAISLER_APBPS2" or "01_060" +- reg : Address and length of the register set for the device +- interrupts : Interrupt numbers for this device + +Optional properties: +- keyboard : if present it indicates that a keyboard is connected, if not + present the driver will assume that a mouse is connected instead + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdfdrivers/input/serio/Kconfig +10
-0@@ -244,4 +244,14 @@ config SERIO_ARC_PS2 To compile this driver as a module, choose M here; the module will be called arc_ps2. +config SERIO_APBPS2 + tristate "GRLIB APBPS2 PS/2 keyboard/mouse controller" + depends on OF + help + Say Y here if you want support for GRLIB APBPS2 peripherals used + to connect to PS/2 keyboard and/or mouse. + + To compile this driver as a module, choose M here: the module will + be called apbps2. + endifdrivers/input/serio/Makefile +1
-0@@ -26,3 +26,4 @@ obj-$(CONFIG_SERIO_AMS_DELTA) += ams_delta_serio.o obj-$(CONFIG_SERIO_XILINX_XPS_PS2) += xilinx_ps2.o obj-$(CONFIG_SERIO_ALTERA_PS2) += altera_ps2.o obj-$(CONFIG_SERIO_ARC_PS2) += arc_ps2.o +obj-$(CONFIG_SERIO_APBPS2) += apbps2.odrivers/input/serio/apbps2.c new file +0
-0
Quoted 8 lines
drivers/input/serio/apbps2.c line 2
Quoted 6 lines
index 0000000..9af129d
drivers/input/serio/apbps2.c new file +2
-0@@ -0,0 +1,228 @@ +/* +* linux/drivers/input/serio/apbps2.c Please drop the file name - this way if we ever need to rename/move file it will not get in the way.
ok.
Quoted 147 lines
Quoted 147 lines
drivers/input/serio/apbps2.c new file +146
-0+* +* Copyright (C) 2013 Aeroflex Gaisler +* +* This driver supports the APBPS2 PS/2 core available in the GRLIB +* VHDL IP core library. +* +* Full documentation of the APBPS2 core can be found here: +* http://www.gaisler.com/products/grlib/grip.pdf +* +* See "Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt" for +* information on open firmware properties. +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* Contributors: Daniel Hellstrom <[email protected]> +*/ +#include <linux/platform_device.h> +#include <linux/of_device.h> +#include <linux/module.h> +#include <linux/serio.h> +#include <linux/errno.h> +#include <linux/interrupt.h> +#include <linux/of_irq.h> +#include <linux/device.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/string.h> +#include <linux/kernel.h> +#include <linux/io.h> + +struct apbps2_regs { +u32 __iomem data;/* 0x00 */ +u32 __iomem status;/* 0x04 */ +u32 __iomem ctrl;/* 0x08 */ +u32 __iomem reload;/* 0x0c */ +}; + +#define APBPS2_STATUS_DR (1<<0) +#define APBPS2_STATUS_PE (1<<1) +#define APBPS2_STATUS_FE (1<<2) +#define APBPS2_STATUS_KI (1<<3) +#define APBPS2_STATUS_RF (1<<4) +#define APBPS2_STATUS_TF (1<<5) +#define APBPS2_STATUS_TCNT (0x1f<<22) +#define APBPS2_STATUS_RCNT (0x1f<<27) + +#define APBPS2_CTRL_RE (1<<0) +#define APBPS2_CTRL_TE (1<<1) +#define APBPS2_CTRL_RI (1<<2) +#define APBPS2_CTRL_TI (1<<3) + +struct apbps2_priv { +struct serio *io; +struct apbps2_regs *regs; +}; + +static irqreturn_t apbps2_isr (int irq,void *dev_id) +{ +struct apbps2_priv *priv = dev_id; +unsigned long status, data, rxflags; +irqreturn_t ret =IRQ_NONE ; + +while ((status =ioread32be (&priv->regs->status)) &APBPS2_STATUS_DR ) { + data =ioread32be (&priv->regs->data); + rxflags = (status &APBPS2_STATUS_PE ) ?SERIO_PARITY :0 ; + rxflags |= (status &APBPS2_STATUS_PE ) ?SERIO_FRAME :0 ; + +/* clear error bits? */ +if (rxflags) +iowrite32be (status, &priv->regs->status); + +serio_interrupt (priv->io, data, rxflags); + + ret =IRQ_HANDLED ; + } + +return ret; +} + +static int apbps2_write (struct serio *io,unsigned char val) +{ +struct apbps2_priv *priv = io->port_data; +unsigned int tleft =10000 ;/* timeout in 100ms */ + +/* delay until PS/2 controller has room for more chars */ +while ((ioread32be (&priv->regs->status) &APBPS2_STATUS_TF ) && tleft--) +udelay (10 ); + +if ((ioread32be (&priv->regs->status) &APBPS2_STATUS_TF ) ==0 ) { +iowrite32be (val, &priv->regs->data); + +iowrite32be (APBPS2_CTRL_RE |APBPS2_CTRL_RI |APBPS2_CTRL_TE , + &priv->regs->ctrl); +return 0 ; + } + +return -ETIMEDOUT ; +} + +static int apbps2_open (struct serio *io) +{ +struct apbps2_priv *priv = io->port_data; +int limit; +unsigned long tmp; + +/* clear error flags */ +iowrite32be (0 , &priv->regs->status); + +/* Clear old data if available (unlikely) */ + limit =1024 ; +while ((ioread32be (&priv->regs->status) &APBPS2_STATUS_DR ) && --limit) + tmp =ioread32be (&priv->regs->data); + +/* Enable reciever and it's interrupt */ +iowrite32be (APBPS2_CTRL_RE |APBPS2_CTRL_RI , &priv->regs->ctrl); + +return 0 ; +} + +static void apbps2_close (struct serio *io) +{ +struct apbps2_priv *priv = io->port_data; + +/* stop interrupts at PS/2 HW level */ +iowrite32be (0 , &priv->regs->ctrl); +} + +/* Initialize one APBPS2 PS/2 core */ +static int apbps2_of_probe (struct platform_device *ofdev) +{ +struct apbps2_priv *priv; +int irq, err; +u32 freq_hz; +struct resource *res; + + priv =devm_kzalloc (&ofdev->dev,sizeof (*priv),GFP_KERNEL ); +if (!priv) { +dev_err (&ofdev->dev,"memory allocation failed\n" ); +return -ENOMEM ; + } +platform_set_drvdata (ofdev, priv); + +/* Find Device Address */
Quoted 8 lines
drivers/input/serio/apbps2.c line 154
Quoted 6 lines
drivers/input/serio/apbps2.c new file +6
-0+ res =platform_get_resource (ofdev,IORESOURCE_MEM ,0 ); + priv->regs =devm_request_and_ioremap (&ofdev->dev, res); +if (!priv->regs) { +dev_err (&ofdev->dev,"io-regs mapping failed\n" ); +return -EADDRNOTAVAIL ; + }Could you please make sure you shut off IRQs in chip here as well, like yo udo in
apbps2_close(), before requesting IRQ?
I will do that, it might not be wise to rely on the boot loader here.
Quoted 23 lines
Quoted 23 lines
drivers/input/serio/apbps2.c new file +22
-0+ +/* IRQ */ + irq =irq_of_parse_and_map (ofdev->dev.of_node,0 ); + err =devm_request_irq (&ofdev->dev, irq, apbps2_isr,IRQF_SHARED , +"apbps2" , priv); +if (err) { +dev_err (&ofdev->dev,"request IRQ%d failed\n" , irq); +return err; + } + +/* Get core frequency */ +if (of_property_read_u32 (ofdev->dev.of_node,"freq" , &freq_hz)) { +dev_err (&ofdev->dev,"unable to get core frequency\n" ); +return -EINVAL ; + } + + priv->io =kzalloc (sizeof (struct serio ),GFP_KERNEL ); +if (!priv->io) +return -ENOMEM ; + + priv->io->id.type =SERIO_8042 ; + priv->io->open = apbps2_open;
Quoted 8 lines
drivers/input/serio/apbps2.c line 181
Quoted 5 lines
drivers/input/serio/apbps2.c new file +5
-0+ priv->io->close = apbps2_close; + priv->io->write = apbps2_write; + priv->io->port_data = priv; +strlcpy (priv->io->name,"APBPS2 PS/2" ,sizeof (priv->io->name)); +strlcpy (priv->io->phys,"apbps2" ,sizeof (priv->io->phys));Phys is supposed to be unique within the system, you may want to use a counter or some other identifying data for particular port. Or is there just one PS/2 port in the system?
Ok, I will use a static counter.
I will resend the patch with the updates.
Thanks,
Daniel
Quoted 52 lines
Quoted 50 lines
drivers/input/serio/apbps2.c new file +47
-0+ +dev_info (&ofdev->dev,"irq = %d, base = 0x%p\n" , irq, priv->regs); + +/* Set reload register to system freq in kHz/10 */ +iowrite32be (freq_hz /10000 , &priv->regs->reload); + +serio_register_port (priv->io); + +return 0 ; +} + +static int apbps2_of_remove (struct platform_device *of_dev) +{ +struct apbps2_priv *priv =platform_get_drvdata (of_dev); + +serio_unregister_port (priv->io); + +return 0 ; +} + +static struct of_device_id apbps2_of_match[] = { + { + .name ="GAISLER_APBPS2" , + }, + { + .name ="01_060" , + }, + {}, +}; + +MODULE_DEVICE_TABLE (of, apbps2_of_match); + +static struct platform_driver apbps2_of_driver = { + .driver = { + .name ="grlib-apbps2" , + .owner =THIS_MODULE , + .of_match_table = apbps2_of_match, + }, + .probe = apbps2_of_probe, + .remove = apbps2_of_remove, +}; + +module_platform_driver (apbps2_of_driver); + +MODULE_AUTHOR ("Aeroflex Gaisler AB." ); +MODULE_DESCRIPTION ("GRLIB APBPS2 PS/2 serial I/O" ); +MODULE_LICENSE ("GPL" );Signature · 1 line
1.7.0.4Thanks.