blackfin: Fit u-boot image size into limited nor flash on blackfin.
PATCH 1/1 blackfin: Fit u-boot image size into limited nor flash on blackfin.
From: Sonic Zhang <[email protected]>
- Disable NAND driver on bf537-stamp.
- Make MMC_SPI optional.
- Disable LCD driver on bf527-ezkit.
- Enlarge BF609 nor flash reserved size from 256k to 512k bytes.
Signed-off-by Sonic Zhang <[email protected]>
Signed-off-by Sonic Zhang <[email protected]>
--- include/configs/bf527-ezkit.h | 12 ++++++------ include/configs/bf537-stamp.h | 10 ++++++---- include/configs/bf609-ezkit.h | 2 ++ 3 files changed, 14 insertions(+), 10 deletions(-)
include/configs/bf527-ezkit.h +6 -6
@@ -149,10 +149,15 @@#define CONFIG_MUSB_TIMEOUT 100000#endif +/* Don't waste time transferring a logo over the UART */ +#if (CONFIG_BFIN_BOOT_MODE !=BFIN_BOOT_UART ) +/*# define CONFIG_VIDEO*/ +#endif /* * Video Settings */ +#ifdef CONFIG_VIDEO #ifdef CONFIG_BF527_EZKIT_REV_2_1 # define CONFIG_LQ035Q1_SPI_BUS 0# define CONFIG_LQ035Q1_SPI_CS 7
@@ -166,7 +171,7 @@#else # define EASYLOGO_HEADER <asm/bfin_logo_230x230_lzma.h>#endif - +#endif /* CONFIG_VIDEO */ /* * Misc Settings
@@ -175,11 +180,6 @@#define CONFIG_RTC_BFIN #define CONFIG_UART_CONSOLE 1 -/* Don't waste time transferring a logo over the UART */ -#if (CONFIG_BFIN_BOOT_MODE !=BFIN_BOOT_UART ) -# define CONFIG_VIDEO -#endif -/* * Pull in common ADI header for remaining command/environment setup
include/configs/bf537-stamp.h +6 -4
@@ -52,7 +52,7 @@#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MONITOR_LEN (768 * 1024)#define CONFIG_SYS_MALLOC_LEN (384 * 1024)
@@ -135,15 +135,17 @@/* * SPI_MMC Settings */ +#define CONFIG_MMC_SPI +#ifdef CONFIG_MMC_SPI #define CONFIG_MMC #define CONFIG_GENERIC_MMC -#define CONFIG_MMC_SPI - +#endif /* * NAND Settings */ /* #define CONFIG_NAND_PLAT */ +#ifdef CONFIG_NAND_PLAT #define CONFIG_SYS_NAND_BASE 0x20212000#define CONFIG_SYS_MAX_NAND_DEVICE 1
@@ -158,7 +160,7 @@#define NAND_PLAT_WRITE_CMD (chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd)#define NAND_PLAT_WRITE_ADR (chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd)#define NAND_PLAT_GPIO_DEV_READY GPIO_PF3 - +#endif /* CONFIG_NAND_PLAT */ /* * CF-CARD IDE-HDD Support
include/configs/bf609-ezkit.h +2 -0
@@ -156,6 +156,8 @@#undef CONFIG_UART_CONSOLE_IS_JTAG#endif +#define CONFIG_BOARD_SIZE_LIMIT $$((512 * 1024)) +/* * Run core 1 from L1 SRAM start address when init uboot on core 0 */
Signature · 1 line
1.7.0.4