v4l controls API

Hello,

I don't know how to get access to the v4l controls on a I2C camera sensor.

My driver structure looks following:

bridge driver -> csi-driver -> sensor driver (includes controls)
register-async-notifer for csi driver register-async-notifer for sensor driver
register video device

The v4l2 API say:
When a sub-device is registered with a V4L2 driver by calling v4l2_device_register_subdev() and the ctrl_handler fields of both v4l2_subdev and v4l2_device are set, then the controls of the subdev will become automatically available in the V4L2 driver as well. If the subdev driver contains controls that already exist in the V4L2 driver, then those will be skipped (so a V4L2 driver can always override a subdev control).

But how can I get access to the controls by asynchronous registration, because the controls are not added to the video device automatically?

Normally I can use:

v4l2-ctl -l -d /dev/video0

I don't know if this forum is the right place for this question, so please answer with a private e-mail [email protected]

------------------------------------------------------------------------
Sebastian Süsens Tel. +49 4321 559 56-27
mycable GmbH Fax +49 4321 559 56-10
Gartenstrasse 10
24534 Neumuenster, Germany Email [email protected]
------------------------------------------------------------------------
mycable GmbH, Managing Director: Michael Carstens-Behrens
USt-IdNr: DE 214 231 199, Amtsgericht Kiel, HRB 1797 NM
------------------------------------------------------------------------
This e-mail and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this e-mail in error, please notify the sender and delete all copies from your system.
------------------------------------------------------------------------

Hello,

I don't know how to get access to the v4l controls on a I2C camera sensor.

My driver structure looks following:

bridge driver -> csi-driver -> sensor driver (includes controls)
register-async-notifer for csi driver register-async-notifer for sensor driver
register video device

The v4l2 API say:
When a sub-device is registered with a V4L2 driver by calling v4l2_device_register_subdev() and the ctrl_handler fields of both v4l2_subdev and v4l2_device are set, then the controls of the subdev will become automatically available in the V4L2 driver as well. If the subdev driver contains controls that already exist in the V4L2 driver, then those will be skipped (so a V4L2 driver can always override a subdev control).

But how can I get access to the controls by asynchronous registration, because the controls are not added to the video device automatically?

Normally I can use:

v4l2-ctl -l -d /dev/video0

I don't know if this forum is the right place for this question, so please answer with a private e-mail [email protected]

------------------------------------------------------------------------
Sebastian Süsens Tel. +49 4321 559 56-27
mycable GmbH Fax +49 4321 559 56-10
Gartenstrasse 10
24534 Neumuenster, Germany Email [email protected]
------------------------------------------------------------------------
mycable GmbH, Managing Director: Michael Carstens-Behrens
USt-IdNr: DE 214 231 199, Amtsgericht Kiel, HRB 1797 NM
------------------------------------------------------------------------
This e-mail and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this e-mail in error, please notify the sender and delete all copies from your system.
------------------------------------------------------------------------

Hey,

I use the driver mx6s_capture kernel 4.9.88
On the device tree it is registered with following name "fsl,imx6s-csi".

Hint:
I have no sub-devices on my systems only /dev/video0

------------------------------------------------------------------------
Sebastian Süsens Tel. +49 4321 559 56-27
mycable GmbH Fax +49 4321 559 56-10
Gartenstrasse 10
24534 Neumuenster, Germany Email [email protected]
------------------------------------------------------------------------
mycable GmbH, Managing Director: Michael Carstens-Behrens
USt-IdNr: DE 214 231 199, Amtsgericht Kiel, HRB 1797 NM
------------------------------------------------------------------------
This e-mail and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this e-mail in error, please notify the sender and delete all copies from your system.
------------------------------------------------------------------------

----- Ursprüngliche Mail -----
Von: "Hans Verkuil" <[email protected]>
An: "Sebastian Süsens" <[email protected]>, "linux-media" <[email protected]>
Gesendet: Montag, 3. Dezember 2018 09:29:14
Betreff: Re: v4l controls API

Quoted 6 lines · Sebastian Süsens

Hello,

I don't know how to get access to the v4l controls on a I2C camera sensor.

My driver structure looks following:

Quoted 8 lines

bridge driver -> csi-driver -> sensor driver (includes controls)
register-async-notifer for csi driver register-async-notifer for sensor driver
register video device

The v4l2 API say:
When a sub-device is registered with a V4L2 driver by calling v4l2_device_register_subdev() and the ctrl_handler fields of both v4l2_subdev and v4l2_device are set, then the controls of the subdev will become automatically available in the V4L2 driver as well. If the subdev driver contains controls that already exist in the V4L2 driver, then those will be skipped (so a V4L2 driver can always override a subdev control).

But how can I get access to the controls by asynchronous registration, because the controls are not added to the video device automatically?

Yes, they are via v4l2_device_register_subdev(), which is called by the async code when the subdev driver arrives.

Note that this assumes that the bridge driver has a control handler that struct v4l2_device points to (the ctrl_handler field).

Also note that certain types of drivers (media controller-based) such as the imx driver do not 'inherit' controls since each subdev has its own v4l-subdevX device node through which its controls can be set. You do not mention which bridge driver you are using, so I can't tell whether or not it falls in this category.

Regards,

Hans

Quoted 22 lines

Normally I can use:

v4l2-ctl -l -d /dev/video0

I don't know if this forum is the right place for this question, so please answer with a private e-mail [email protected]

------------------------------------------------------------------------
Sebastian Süsens Tel. +49 4321 559 56-27
mycable GmbH Fax +49 4321 559 56-10
Gartenstrasse 10
24534 Neumuenster, Germany Email [email protected]
------------------------------------------------------------------------
mycable GmbH, Managing Director: Michael Carstens-Behrens
USt-IdNr: DE 214 231 199, Amtsgericht Kiel, HRB 1797 NM
------------------------------------------------------------------------
This e-mail and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this e-mail in error, please notify the sender and delete all copies from your system.
------------------------------------------------------------------------

Hey,

I use the driver mx6s_capture kernel 4.9.88
On the device tree it is registered with following name "fsl,imx6s-csi".

Hint:
I have no sub-devices on my systems only /dev/video0

------------------------------------------------------------------------
Sebastian Süsens Tel. +49 4321 559 56-27
mycable GmbH Fax +49 4321 559 56-10
Gartenstrasse 10
24534 Neumuenster, Germany Email [email protected]
------------------------------------------------------------------------
mycable GmbH, Managing Director: Michael Carstens-Behrens
USt-IdNr: DE 214 231 199, Amtsgericht Kiel, HRB 1797 NM
------------------------------------------------------------------------
This e-mail and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this e-mail in error, please notify the sender and delete all copies from your system.
------------------------------------------------------------------------

----- Ursprüngliche Mail -----
Von: "Hans Verkuil" <[email protected]>
An: "Sebastian Süsens" <[email protected]>, "linux-media" <[email protected]>
Gesendet: Montag, 3. Dezember 2018 09:29:14
Betreff: Re: v4l controls API

Quoted 6 lines · Sebastian Süsens

Hello,

I don't know how to get access to the v4l controls on a I2C camera sensor.

My driver structure looks following:

Quoted 8 lines

bridge driver -> csi-driver -> sensor driver (includes controls)
register-async-notifer for csi driver register-async-notifer for sensor driver
register video device

The v4l2 API say:
When a sub-device is registered with a V4L2 driver by calling v4l2_device_register_subdev() and the ctrl_handler fields of both v4l2_subdev and v4l2_device are set, then the controls of the subdev will become automatically available in the V4L2 driver as well. If the subdev driver contains controls that already exist in the V4L2 driver, then those will be skipped (so a V4L2 driver can always override a subdev control).

But how can I get access to the controls by asynchronous registration, because the controls are not added to the video device automatically?

Yes, they are via v4l2_device_register_subdev(), which is called by the async code when the subdev driver arrives.

Note that this assumes that the bridge driver has a control handler that struct v4l2_device points to (the ctrl_handler field).

Also note that certain types of drivers (media controller-based) such as the imx driver do not 'inherit' controls since each subdev has its own v4l-subdevX device node through which its controls can be set. You do not mention which bridge driver you are using, so I can't tell whether or not it falls in this category.

Regards,

Hans

Quoted 22 lines

Normally I can use:

v4l2-ctl -l -d /dev/video0

I don't know if this forum is the right place for this question, so please answer with a private e-mail [email protected]

------------------------------------------------------------------------
Sebastian Süsens Tel. +49 4321 559 56-27
mycable GmbH Fax +49 4321 559 56-10
Gartenstrasse 10
24534 Neumuenster, Germany Email [email protected]
------------------------------------------------------------------------
mycable GmbH, Managing Director: Michael Carstens-Behrens
USt-IdNr: DE 214 231 199, Amtsgericht Kiel, HRB 1797 NM
------------------------------------------------------------------------
This e-mail and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this e-mail in error, please notify the sender and delete all copies from your system.
------------------------------------------------------------------------