watchdog: w83627hf: Convert to watchdog infrastructure
Guenter Roeck
maintainercover watchdog: w83627hf: Convert to watchdog infrastructure
Convert to watchdog infrastructure, cleanup, add support for additional chips, and merge with W83697HF and W83697UG watchdog drivers.
Tested with NCT6775 and NCT6776. I'll be able to test the code with W83627UHG. Additional test feedback, especially for other chips, would be appreciated.
Guenter Roeck
maintainerPATCH 1/8 watchdog: w83627hf: Convert to watchdog infrastructure
--- drivers/watchdog/Kconfig | 1 + drivers/watchdog/w83627hf_wdt.c | 234 ++++++++------------------------------- 2 files changed, 47 insertions(+), 188 deletions(-)
drivers/watchdog/Kconfig +1 -0
@@ -856,6 +856,7 @@ config VIA_WDT config W83627HF_WDT tristate "W83627HF/W83627DHG Watchdog Timer" depends on X86 + select WATCHDOG_CORE ---help--- This is the driver for the hardware watchdog on the W83627HF chipset as used in Advantech PC-9578 and Tyan S2721-533 motherboards
drivers/watchdog/w83627hf_wdt.c +46 -188
343 lines not on this page · raw message
Signature · 6 lines
1.7.9.7 -- To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Guenter Roeck
maintainerPATCH 2/8 watchdog: w83627hf: Enable watchdog only once
In reply to Guenter RoeckIt is unnecessary to enable the logical device and WDT0 each time the watchdog is accessed. Do it only once during initialization.
--- drivers/watchdog/w83627hf_wdt.c | 35 +++++++++++++++++------------------ 1 file changed, 17 insertions(+), 18 deletions(-)
drivers/watchdog/w83627hf_wdt.c +17 -18
@@ -60,28 +60,10 @@ MODULE_PARM_DESC(wdt_io, "w83627hf/thf WDT io port (default 0x2E)");static void w83627hf_select_wd_register (void ) { -unsigned char c;outb_p (0x87 ,WDT_EFER );/* Enter extended function mode */ outb_p (0x87 ,WDT_EFER );/* Again according to manual */ - -outb (0x20 ,WDT_EFER );/* check chip version */ - c =inb (WDT_EFDR ); -if (c ==0x82 ) {/* W83627THF */ -outb_p (0x2b ,WDT_EFER );/* select GPIO3 */ - c = ((inb_p (WDT_EFDR ) &0xf7 ) |0x04 );/* select WDT0 */ -outb_p (0x2b ,WDT_EFER ); -outb_p (c,WDT_EFDR );/* set GPIO3 to WDT0 */ - }else if (c ==0x88 || c ==0xa0 ) {/* W83627EHF / W83627DHG */ -outb_p (0x2d ,WDT_EFER );/* select GPIO5 */ - c =inb_p (WDT_EFDR ) & ~0x01 ;/* PIN77 -> WDT0# */ -outb_p (0x2d ,WDT_EFER ); -outb_p (c,WDT_EFDR );/* set GPIO5 to WDT0 */ - } -outb_p (0x07 ,WDT_EFER );/* point to logical device number reg */ outb_p (0x08 ,WDT_EFDR );/* select logical device 8 (GPIO2) */ -outb_p (0x30 ,WDT_EFER );/* select CR30 */ -outb_p (0x01 ,WDT_EFDR );/* set bit 0 to activate GPIO2 */ }static void w83627hf_unselect_wd_register (void )
@@ -98,6 +80,23 @@ static void w83627hf_init(void)w83627hf_select_wd_register (); +outb (0x20 ,WDT_EFER );/* check chip version */ + t =inb (WDT_EFDR ); +if (t ==0x82 ) {/* W83627THF */ +outb_p (0x2b ,WDT_EFER );/* select GPIO3 */ + t = ((inb_p (WDT_EFDR ) &0xf7 ) |0x04 );/* select WDT0 */ +outb_p (0x2b ,WDT_EFER ); +outb_p (t,WDT_EFDR );/* set GPIO3 to WDT0 */ + }else if (t ==0x88 || t ==0xa0 ) {/* W83627EHF / W83627DHG */ +outb_p (0x2d ,WDT_EFER );/* select GPIO5 */ + t =inb_p (WDT_EFDR ) & ~0x01 ;/* PIN77 -> WDT0# */ +outb_p (0x2d ,WDT_EFER ); +outb_p (t,WDT_EFDR );/* set GPIO5 to WDT0 */ + } + +outb_p (0x30 ,WDT_EFER );/* select CR30 */ +outb_p (0x01 ,WDT_EFDR );/* set bit 0 to activate GPIO2 */ +outb_p (0xF6 ,WDT_EFER );/* Select CRF6 */ t =inb_p (WDT_EFDR );/* read CRF6 */ if (t !=0 ) {
Signature · 1 line
1.7.9.7
Guenter Roeck
maintainerPATCH 3/8 watchdog: w83627hf: Enable watchdog device only if not already enabled
In reply to Guenter RoeckThere is no need to enable the watchdog device if it is already enabled. Also, when enabling the watchdog device, only set the watchdog device enable bit and do not touch other bits; depending on the chip type, those bits may enable other functionality.
--- drivers/watchdog/w83627hf_wdt.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
drivers/watchdog/w83627hf_wdt.c +3 -1
@@ -95,7 +95,9 @@ static void w83627hf_init(void) }outb_p (0x30 ,WDT_EFER );/* select CR30 */ -outb_p (0x01 ,WDT_EFDR );/* set bit 0 to activate GPIO2 */ + t =inb (WDT_EFDR ); +if (!(t &0x01 )) +outb_p (t |0x01 ,WDT_EFDR );/* set bit 0 to activate GPIO2 */ outb_p (0xF6 ,WDT_EFER );/* Select CRF6 */ t =inb_p (WDT_EFDR );/* read CRF6 */
Signature · 1 line
1.7.9.7
Guenter Roeck
maintainerPATCH 4/8 watchdog: w83627hf: Use helper functions to access superio registers
In reply to Guenter RoeckUse helper functions named similar to other drivers to access superio registers.
--- drivers/watchdog/w83627hf_wdt.c | 97 +++++++++++++++++++++------------------ 1 file changed, 52 insertions(+), 45 deletions(-)
drivers/watchdog/w83627hf_wdt.c +52 -45
@@ -58,15 +58,32 @@ MODULE_PARM_DESC(wdt_io, "w83627hf/thf WDT io port (default 0x2E)");(same as EFER) */ #define WDT_EFDR (WDT_EFIR+1)/* Extended Function Data Register */ -static void w83627hf_select_wd_register (void ) +#define W83627HF_LD_WDT 0x08 + +static void superio_outb (int reg,int val) +{ +outb (reg,WDT_EFER ); +outb (val,WDT_EFDR ); +} + +static inline int superio_inb (int reg) +{ +outb (reg,WDT_EFER ); +return inb (WDT_EFDR ); +} + +static void superio_enter (void ) {outb_p (0x87 ,WDT_EFER );/* Enter extended function mode */ outb_p (0x87 ,WDT_EFER );/* Again according to manual */ -outb_p (0x07 ,WDT_EFER );/* point to logical device number reg */ -outb_p (0x08 ,WDT_EFDR );/* select logical device 8 (GPIO2) */ } -static void w83627hf_unselect_wd_register (void ) +static void superio_select (int ld) +{ +superio_outb (0x07 , ld); +} + +static void superio_exit (void ) {outb_p (0xAA ,WDT_EFER );/* Leave extended function mode */ }
@@ -78,58 +95,48 @@ static void w83627hf_init(void) {unsigned char t; -w83627hf_select_wd_register (); - -outb (0x20 ,WDT_EFER );/* check chip version */ - t =inb (WDT_EFDR ); +superio_enter (); +superio_select (W83627HF_LD_WDT ); + t =superio_inb (0x20 );/* check chip version */ if (t ==0x82 ) {/* W83627THF */ -outb_p (0x2b ,WDT_EFER );/* select GPIO3 */ - t = ((inb_p (WDT_EFDR ) &0xf7 ) |0x04 );/* select WDT0 */ -outb_p (0x2b ,WDT_EFER ); -outb_p (t,WDT_EFDR );/* set GPIO3 to WDT0 */ + t = (superio_inb (0x2b ) &0xf7 ); +superio_outb (0x2b , t |0x04 );/* set GPIO3 to WDT0 */ }else if (t ==0x88 || t ==0xa0 ) {/* W83627EHF / W83627DHG */ -outb_p (0x2d ,WDT_EFER );/* select GPIO5 */ - t =inb_p (WDT_EFDR ) & ~0x01 ;/* PIN77 -> WDT0# */ -outb_p (0x2d ,WDT_EFER ); -outb_p (t,WDT_EFDR );/* set GPIO5 to WDT0 */ + t =superio_inb (0x2d ); +superio_outb (0x2d , t & ~0x01 );/* set GPIO5 to WDT0 */ } -outb_p (0x30 ,WDT_EFER );/* select CR30 */ - t =inb (WDT_EFDR ); +/* set CR30 bit 0 to activate GPIO2 */ + t =superio_inb (0x30 );if (!(t &0x01 )) -outb_p (t |0x01 ,WDT_EFDR );/* set bit 0 to activate GPIO2 */ +superio_outb (0x30 , t |0x01 ); -outb_p (0xF6 ,WDT_EFER );/* Select CRF6 */ - t =inb_p (WDT_EFDR );/* read CRF6 */ + t =superio_inb (0xF6 );if (t !=0 ) {pr_info ("Watchdog already running. Resetting timeout to %d sec\n" ,WATCHDOG_TIMEOUT ); -outb_p (WATCHDOG_TIMEOUT ,WDT_EFDR );/* Write back to CRF6 */ +superio_outb (0xf6 ,WATCHDOG_TIMEOUT ); } -outb_p (0xF5 ,WDT_EFER );/* Select CRF5 */ - t =inb_p (WDT_EFDR );/* read CRF5 */ - t &= ~0x0C ;/* set second mode & disable keyboard -turning off watchdog */ - t |=0x02 ;/* enable the WDTO# output low pulse -to the KBRST# pin (PIN60) */ -outb_p (t,WDT_EFDR );/* Write back to CRF5 */ - -outb_p (0xF7 ,WDT_EFER );/* Select CRF7 */ - t =inb_p (WDT_EFDR );/* read CRF7 */ - t &= ~0xC0 ;/* disable keyboard & mouse turning off -watchdog */ -outb_p (t,WDT_EFDR );/* Write back to CRF7 */ - -w83627hf_unselect_wd_register (); +/* set second mode & disable keyboard turning off watchdog */ + t =superio_inb (0xF5 ) & ~0x0C ; +/* enable the WDTO# output low pulse to the KBRST# pin */ + t |=0x02 ; +superio_outb (0xF5 , t); + +/* disable keyboard & mouse turning off watchdog */ + t =superio_inb (0xF7 ) & ~0xC0 ; +superio_outb (0xF7 , t); + +superio_exit (); }static int wdt_set_time (unsigned int timeout) { -w83627hf_select_wd_register (); -outb_p (0xF6 ,WDT_EFER );/* Select CRF6 */ -outb_p (timeout,WDT_EFDR );/* Write Timeout counter to CRF6 */ -w83627hf_unselect_wd_register (); +superio_enter (); +superio_select (W83627HF_LD_WDT ); +superio_outb (0xF6 , timeout); +superio_exit ();return 0 ; }
@@ -155,10 +162,10 @@ static unsigned int wdt_get_time(struct watchdog_device *wdog) {unsigned int timeleft; -w83627hf_select_wd_register (); -outb_p (0xF6 ,WDT_EFER ); - timeleft =inb (WDT_EFDR ); -w83627hf_unselect_wd_register (); +superio_enter (); +superio_select (W83627HF_LD_WDT ); + timeleft =superio_inb (0xF6 ); +superio_exit ();return timeleft; }
Signature · 1 line
1.7.9.7
Guenter Roeck
maintainerPATCH 5/8 watchdog: w83627hf: Auto-detect IO address and supported chips
In reply to Guenter RoeckInstead of requiring the user to provide an IO address per module parameter, auto-detect it as well as supported chips.
--- drivers/watchdog/w83627hf_wdt.c | 121 ++++++++++++++++++++++++++++++++------- 1 file changed, 101 insertions(+), 20 deletions(-)
drivers/watchdog/w83627hf_wdt.c +101 -20
@@ -44,10 +44,10 @@#define WATCHDOG_NAME "w83627hf/thf/hg/dhg WDT"#define WATCHDOG_TIMEOUT 60/* 60 sec default timeout */ -/* You must set this - there is no sane way to probe for this board. */ -static int wdt_io =0x2E ; -module_param (wdt_io, int,0 ); -MODULE_PARM_DESC (wdt_io,"w83627hf/thf WDT io port (default 0x2E)" ); +static int wdt_io; + +enum chips { w83627hf, w83637hf, w83627thf, w83687thf, w83627ehf, w83627dhg, + w83627uhg };/* * Kernel methods.
@@ -60,6 +60,14 @@ MODULE_PARM_DESC(wdt_io, "w83627hf/thf WDT io port (default 0x2E)");#define W83627HF_LD_WDT 0x08 +#define W83627HF_ID 0x52 +#define W83637HF_ID 0x70 +#define W83627THF_ID 0x82 +#define W83687THF_ID 0x85 +#define W83627EHF_ID 0x88 +#define W83627DHG_ID 0xa0 +#define W83627UHG_ID 0xa2 +static void superio_outb (int reg,int val) {outb (reg,WDT_EFER );
@@ -88,29 +96,44 @@ static void superio_exit(void)outb_p (0xAA ,WDT_EFER );/* Leave extended function mode */ } -/* tyan motherboards seem to set F5 to 0x4C ? -* So explicitly init to appropriate value. */ - -static void w83627hf_init (void ) +static void w83627hf_init (enum chips chip) {unsigned char t;superio_enter ();superio_select (W83627HF_LD_WDT ); - t =superio_inb (0x20 );/* check chip version */ -if (t ==0x82 ) {/* W83627THF */ - t = (superio_inb (0x2b ) &0xf7 ); -superio_outb (0x2b , t |0x04 );/* set GPIO3 to WDT0 */ - }else if (t ==0x88 || t ==0xa0 ) {/* W83627EHF / W83627DHG */ - t =superio_inb (0x2d ); -superio_outb (0x2d , t & ~0x01 );/* set GPIO5 to WDT0 */ - }/* set CR30 bit 0 to activate GPIO2 */ t =superio_inb (0x30 );if (!(t &0x01 ))superio_outb (0x30 , t |0x01 ); +switch (chip) { +case w83627hf: + t =superio_inb (0x2B ) & ~0x10 ; +superio_outb (0x2B , t);/* set GPIO24 to WDT0 */ +break ; +case w83627thf: + t = (superio_inb (0x2B ) & ~0x08 ) |0x04 ; +superio_outb (0x2B , t);/* set GPIO3 to WDT0 */ +break ; +case w83627ehf: +case w83627dhg: +case w83627uhg: + t =superio_inb (0x2D ) & ~0x01 ;/* PIN77 -> WDT0# */ +superio_outb (0x2D , t);/* set GPIO5 to WDT0 */ + t =superio_inb (0xF5 ); + t |=0x02 ;/* enable the WDTO# output low pulse +* to the KBRST# pin */ +superio_outb (0xF5 , t); +break ; +case w83637hf: +case w83687thf: +break ; +default : +break ; + } + t =superio_inb (0xF6 );if (t !=0 ) { pr_info("Watchdog already running. Resetting timeout to %d sec\n",
@@ -120,8 +143,6 @@ static void w83627hf_init(void)/* set second mode & disable keyboard turning off watchdog */ t =superio_inb (0xF5 ) & ~0x0C ; -/* enable the WDTO# output low pulse to the KBRST# pin */ - t |=0x02 ;superio_outb (0xF5 , t);/* disable keyboard & mouse turning off watchdog */
@@ -217,19 +238,79 @@ static struct notifier_block wdt_notifier = { .notifier_call = wdt_notify_sys, }; +static int wdt_find (int addr) +{ +u8 val; +int ret = -ENODEV ; + +superio_enter (); +superio_select (W83627HF_LD_WDT ); + val =superio_inb (0x20 ); +switch (val) { +case W83627HF_ID : + ret = w83627hf; +break ; +case W83637HF_ID : + ret = w83637hf; +break ; +case W83627THF_ID : + ret = w83627thf; +break ; +case W83687THF_ID : + ret = w83687thf; +break ; +case W83627EHF_ID : + ret = w83627ehf; +break ; +case W83627DHG_ID : + ret = w83627dhg; +break ; +case W83627UHG_ID : + ret = w83627uhg; +break ; +case 0xff : +break ; +default : +pr_err ("Unsupported chip ID: 0x%02x\n" , val); +break ; + } +superio_exit (); +return ret; +} +static int __init wdt_init (void ) {int ret;bool nowayout =WATCHDOG_NOWAYOUT ; +int chip; +const char *const chip_name[] = { +"W83627HF" , +"W83637HF" , +"W83627THF" , +"W83687THF" , +"W83627EHF" , +"W83627DHG" , +"W83627UHG" , + }; + + wdt_io =0x2e ; + chip =wdt_find (0x2e ); +if (chip <0 ) { + wdt_io =0x4e ; + chip =wdt_find (0x4e ); +if (chip <0 ) +return chip; + } -pr_info ("WDT driver for the Winbond(TM) W83627HF/THF/HG/DHG Super I/O chip initialising\n" ); +pr_info ("WDT driver for %s Super I/O chip initialising, nowayout=%d\n" , + chip_name[chip], nowayout);if (!request_region (wdt_io,1 ,WATCHDOG_NAME )) {pr_err ("I/O address 0x%04x already in use\n" , wdt_io);return -EIO ; } -w83627hf_init (); +w83627hf_init (chip); ret =register_reboot_notifier (&wdt_notifier);if (ret !=0 ) {
Signature · 1 line
1.7.9.7
Guenter Roeck
maintainerPATCH 6/8 watchdog: w83627hf: Add support for additional chips
In reply to Guenter RoeckW83667HG-B, NCT6775, NCT6776 have the same watchdog registers as the other supported chips but require a slightly different initialization.
--- drivers/watchdog/Kconfig | 18 ++++++++++++++---- drivers/watchdog/w83627hf_wdt.c | 29 ++++++++++++++++++++++++++++- 2 files changed, 42 insertions(+), 5 deletions(-)
drivers/watchdog/Kconfig +14 -4
@@ -854,13 +854,23 @@ config VIA_WDT Most people will say N. config W83627HF_WDT - tristate "W83627HF/W83627DHG Watchdog Timer" + tristate "Watchdog timer for W83627HF/W83627DHG and compatibles" depends on X86 select WATCHDOG_CORE ---help--- - This is the driver for the hardware watchdog on the W83627HF chipset - as used in Advantech PC-9578 and Tyan S2721-533 motherboards - (and likely others). The driver also supports the W83627DHG chip. + This is the driver for the hardware watchdog on the following + Super I/O chips. + W83627DHG + W83627HF + W83627EHF + W83627THF + W83627UHG + W83637HF + W83667HG-B + W83687THF + NCT6775 + NCT6776 + This watchdog simply watches your kernel to make sure it doesn't freeze, and if it does, it reboots your computer after a certain amount of time.
drivers/watchdog/w83627hf_wdt.c +28 -1
@@ -47,7 +47,7 @@static int wdt_io;enum chips { w83627hf, w83637hf, w83627thf, w83687thf, w83627ehf, w83627dhg, - w83627uhg }; + w83627uhg, w83667hg_b, nct6775, nct6776 };/* * Kernel methods.
@@ -67,6 +67,9 @@ enum chips { w83627hf, w83637hf, w83627thf, w83687thf, w83627ehf, w83627dhg,#define W83627EHF_ID 0x88#define W83627DHG_ID 0xa0#define W83627UHG_ID 0xa2 +#define W83667HG_B_ID 0xb3 +#define NCT6775_ID 0xb4 +#define NCT6776_ID 0xc3static void superio_outb (int reg,int val) {
@@ -130,6 +133,18 @@ static void w83627hf_init(enum chips chip)case w83637hf:case w83687thf:break ; +case w83667hg_b: +case nct6775: +case nct6776: +/* +* These chips support more than one WDTO# output pin. +* Don't touch it, and hope the BIOS does the right thing. +*/ + t =superio_inb (0xF5 ); + t |=0x02 ;/* enable the WDTO# output low pulse +* to the KBRST# pin */ +superio_outb (0xF5 , t); +break ;default :break ; }
@@ -268,6 +283,15 @@ static int wdt_find(int addr)case W83627UHG_ID : ret = w83627uhg;break ; +case W83667HG_B_ID : + ret = w83667hg_b; +break ; +case NCT6775_ID : + ret = nct6775; +break ; +case NCT6776_ID : + ret = nct6776; +break ;case 0xff :break ;default :
@@ -291,6 +315,9 @@ static int __init wdt_init(void)"W83627EHF" ,"W83627DHG" ,"W83627UHG" , +"W83667HG-B" , +"NCT6775" , +"NCT6776" , }; wdt_io =0x2e ;
Signature · 1 line
1.7.9.7
Guenter Roeck
maintainerPATCH 7/8 watchdog: w83627hf: Add support for W83697HF and W83697UG
In reply to Guenter RoeckMajor difference is that the watchdog control and counter registers are different on both chips.
--- drivers/watchdog/Kconfig | 2 ++ drivers/watchdog/w83627hf_wdt.c | 60 +++++++++++++++++++++++++++++++-------- 2 files changed, 50 insertions(+), 12 deletions(-)
drivers/watchdog/Kconfig +2 -0
@@ -868,6 +868,8 @@ config W83627HF_WDT W83637HF W83667HG-B W83687THF + W83697HF + W83697UG NCT6775 NCT6776
drivers/watchdog/w83627hf_wdt.c +48 -12
142 lines not on this page · raw message
Signature · 1 line
1.7.9.7
Guenter Roeck
maintainerPATCH 8/8 watchdog: Remove drivers for W83697HF and W83697UG
In reply to Guenter RoeckSince both chips are now supported by the w83627hf watchdog driver, the chip specific drivers are no longer needed and can be removed.
--- drivers/watchdog/Kconfig | 30 --- drivers/watchdog/Makefile | 2 - drivers/watchdog/w83697hf_wdt.c | 461 --------------------------------------- drivers/watchdog/w83697ug_wdt.c | 398 --------------------------------- 4 files changed, 891 deletions(-) delete mode 100644 drivers/watchdog/w83697hf_wdt.c delete mode 100644 drivers/watchdog/w83697ug_wdt.c
drivers/watchdog/Kconfig +0 -30
@@ -882,36 +882,6 @@ config W83627HF_WDT Most people will say N. -config W83697HF_WDT - tristate "W83697HF/W83697HG Watchdog Timer" - depends on X86 - ---help--- - This is the driver for the hardware watchdog on the W83697HF/HG - chipset as used in Dedibox/VIA motherboards (and likely others). - This watchdog simply watches your kernel to make sure it doesn't - freeze, and if it does, it reboots your computer after a certain - amount of time. - - To compile this driver as a module, choose M here: the - module will be called w83697hf_wdt. - - Most people will say N. - -config W83697UG_WDT - tristate "W83697UG/W83697UF Watchdog Timer" - depends on X86 - ---help--- - This is the driver for the hardware watchdog on the W83697UG/UF - chipset as used in MSI Fuzzy CX700 VIA motherboards (and likely others). - This watchdog simply watches your kernel to make sure it doesn't - freeze, and if it does, it reboots your computer after a certain - amount of time. - - To compile this driver as a module, choose M here: the - module will be called w83697ug_wdt. - - Most people will say N. - config W83877F_WDT tristate "W83877F (EMACS) Watchdog Timer" depends on X86
drivers/watchdog/Makefile +0 -2
@@ -103,8 +103,6 @@ obj-$(CONFIG_SMSC_SCH311X_WDT) += sch311x_wdt.o obj-$(CONFIG_SMSC37B787_WDT) += smsc37b787_wdt.o obj-$(CONFIG_VIA_WDT) += via_wdt.o obj-$(CONFIG_W83627HF_WDT) += w83627hf_wdt.o -obj-$(CONFIG_W83697HF_WDT) += w83697hf_wdt.o -obj-$(CONFIG_W83697UG_WDT) += w83697ug_wdt.o obj-$(CONFIG_W83877F_WDT) += w83877f_wdt.o obj-$(CONFIG_W83977F_WDT) += w83977f_wdt.o obj-$(CONFIG_MACHZ_WDT) += machzwd.o
drivers/watchdog/w83697hf_wdt.c deleted +0 -461
461 lines not on this page · raw message
drivers/watchdog/w83697ug_wdt.c deleted +0 -398
398 lines not on this page · raw message
Signature · 6 lines
1.7.9.7 -- To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html