EXYNOS5: Enable DWMMC, add FDT support for DWMMC and enable EMMC boot
Subsystems (5)
v7 cover EXYNOS5: Enable DWMMC, add FDT support for DWMMC and enable EMMC boot
This patch set enables and initialises DWMMC for Exynos5250 on SMDK5250. Adds driver changes required for DWMMC.
Adds FDT support for DWMMC.
Adds EMMC boot support for SMDK5250.
This patch set is based on:
"EXYNOS: mmc: support DesignWare Controller for Samsung-SoC", which is merged in u-boot-mmc.
"Exynos: clock: support get_mmc_clk for exynos".
"Add DT based ethernet driver for SMDK5250".
"SMDK5250: Add FDT support" present at the following link
http://comments.gmane.org/gmane.comp.boot-loaders.u-boot/149991
Changes from V1:
1)Corrected in response to review comments.
2)Created separate board files for FDT and non-FDT versions. 3)Added binding file for DWMMC device node.
4)Removed the propname 'index' from device node. 5)Prefixed the vendor name 'samsung' before propname in device node. 6)Ensured to have same signature for the function exynos_dwmci_init() for both FDT and non-FDT versions.
7)EMMC clock setting has been moved from spl_boot.c to clock_init.c.
Changes from V2:
1)Updation of commit message and resubmition of proper patch set.
Changes from V3:
1)Updated to use the macro DWMCI_CTRL_SEND_AS_CCSD instead of the hard coded value (1 << 10).
2)In the file exynos_dw_mmc.c, replaced the new function exynos5_mmc_set_clk_div() with the existing function set_mmc_clk(). set_mmc_clk() will do the purpose.
3)In the file exynos_dw_mmc.c, computation of FSYS block clock divisor (pre-ratio) value is added.
4)Removed the new function exynos5_mmc_set_clk_div() from clock.c.
Changes from V4:
1)Updated the function dwmci_send_cmd() to use get_timer() instead of using mdelay(1).
2)Replaced the function call 'exynos_dwmmc_init(0, 8);' with the function exynos_dwmmc_add_port() in smdk5250.c.
3)The function get_irom_func(int index) has been added to avoid type casting@many places.
4)Used the generic function "mmc_boot_part_access()" instead of two functions "mmc_boot_open()" and "mmc_boot_close()". By doing so user can specify which boot partition to be accessed (opened / closed).
Changes from V5:
1)Added the 'removable' flag to mmc device node. 2)Changed the mmc clock value from 50MHz to 52MHz in the function exynos_dwmci_add_port() present in file drivers/mmc/exynos_dw_mmc.c. 3)Enabled CONFIG_LCD only for non-FDT operation. 4)Removed the function call i2c_init() present inside the function board_i2c_init().
Changes from V6:
1)Re-based to the patch "SMDK5250: Add PMIC voltage settings".
Amar (10):
FDT: Add compatible string for DWMMC
EXYNOS5: FDT: Add DWMMC device node data
DWMMC: Initialise dwmci and resolve EMMC read write issues
EXYNOS5: DWMMC: Added FDT support for DWMMC
EXYNOS5: DWMMC: Initialise the local variable to avoid unwanted
results.
SMDK5250: Initialise and Enable DWMMC, support FDT and non-FDT
MMC: APIs to support resize of EMMC boot partition
SMDK5250: Enable EMMC booting
COMMON: MMC: Command to support EMMC booting and to resize EMMC boot
partition
EXYNOS5: I2C: Added FDT and non-FDT support for I2C
arch/arm/cpu/armv7/exynos/clock.c | 4 +- arch/arm/dts/exynos5250.dtsi | 31 +++ arch/arm/include/asm/arch-exynos/clk.h | 3 + arch/arm/include/asm/arch-exynos/dwmmc.h | 11 +- board/samsung/dts/exynos5250-smdk5250.dts | 24 +++ board/samsung/smdk5250/Makefile | 4 + board/samsung/smdk5250/clock_init.c | 15 ++ board/samsung/smdk5250/clock_init.h | 5 + board/samsung/smdk5250/exynos5-dt.c | 319 ++++++++++++++++++++++++++++++ board/samsung/smdk5250/smdk5250.c | 165 ++++++---------- board/samsung/smdk5250/spl_boot.c | 52 ++++- common/cmd_mmc.c | 98 ++++++++- doc/device-tree-bindings/exynos/dwmmc.txt | 54 +++++ drivers/i2c/s3c24x0_i2c.c | 12 +- drivers/mmc/dw_mmc.c | 25 ++- drivers/mmc/exynos_dw_mmc.c | 127 +++++++++++- drivers/mmc/mmc.c | 132 +++++++++++++ include/configs/exynos5250-dt.h | 8 + include/dwmmc.h | 3 + include/fdtdec.h | 1 + include/mmc.h | 26 +++ lib/fdtdec.c | 1 + 22 files changed, 974 insertions(+), 146 deletions(-) create mode 100644 board/samsung/smdk5250/exynos5-dt.c create mode 100644 doc/device-tree-bindings/exynos/dwmmc.txt
Signature · 1 line
1.8.0
PATCH v7 1/10 FDT: Add compatible string for DWMMC
Add required compatible information for DWMMC driver.
---
Changes since V1:
No change.
Changes since V2:
1)Updation of commit message and resubmition of proper patch set.
Changes since V3:
No change.
Changes since V4:
No change.
Changes since V5:
No change.
include/fdtdec.h | 1 + lib/fdtdec.c | 1 + 2 files changed, 2 insertions(+)
include/fdtdec.h +1 -0
@@ -81,6 +81,7 @@ enum fdt_compat_id {COMPAT_SAMSUNG_EXYNOS_EHCI ,/* Exynos EHCI controller */ COMPAT_SAMSUNG_EXYNOS_USB_PHY ,/* Exynos phy controller for usb2.0 */ COMPAT_MAXIM_MAX77686_PMIC ,/* MAX77686 PMIC */ +COMPAT_SAMSUNG_EXYNOS5_DWMMC ,/* Exynos5 DWMMC controller */ COMPAT_COUNT, };
lib/fdtdec.c +1 -0
@@ -56,6 +56,7 @@ static const char * const compat_names[COMPAT_COUNT] = {COMPAT (SAMSUNG_EXYNOS_EHCI ,"samsung,exynos-ehci" ),COMPAT (SAMSUNG_EXYNOS_USB_PHY ,"samsung,exynos-usb-phy" ),COMPAT (MAXIM_MAX77686_PMIC ,"maxim,max77686_pmic" ), + COMPAT(SAMSUNG_EXYNOS5_DWMMC, "samsung,exynos5250-dwmmc"), };const char *fdtdec_get_compatible (enum fdt_compat_id id)
Signature · 1 line
1.8.0
PATCH v7 1/10 FDT: Add compatible string for DWMMC
Hi Amar,
Quoted 44 lines · Amar
Add required compatible information for DWMMC driver.
Signed-off-by Vivek Gautam <[email protected]>Signed-off-by Amar <[email protected]>Acked-by Jaehoon Chung <[email protected]>---
Changes since V1:
No change.Changes since V2:
1)Updation of commit message and resubmition of proper patch set.Changes since V3:
No change.Changes since V4:
No change.Changes since V5:
No change.include/fdtdec.h | 1 + lib/fdtdec.c | 1 + 2 files changed, 2 insertions(+)include/fdtdec.h +0
-0@@ -81,6 +81,7 @@ enum fdt_compat_id {COMPAT_SAMSUNG_EXYNOS_EHCI ,/* Exynos EHCI controller */ COMPAT_SAMSUNG_EXYNOS_USB_PHY, /* Exynos phy controller forusb2.0 */
COMPAT_MAXIM_MAX77686_PMIC, /* MAX77686 PMIC */include/fdtdec.h +1
-0+COMPAT_SAMSUNG_EXYNOS5_DWMMC ,/* Exynos5 DWMMC controller */ COMPAT_COUNT, };lib/fdtdec.c +0
-0
lib/fdtdec.c static const char * const compat_names[COMPAT_COUNT] = { · line 62
Quoted 7 lines
lib/fdtdec.c +1
-0@@ -56,6 +56,7 @@ static const char * const compat_names[COMPAT_COUNT] = {COMPAT (SAMSUNG_EXYNOS_EHCI ,"samsung,exynos-ehci" ),COMPAT (SAMSUNG_EXYNOS_USB_PHY ,"samsung,exynos-usb-phy" ),COMPAT (MAXIM_MAX77686_PMIC ,"maxim,max77686_pmic" ), + COMPAT(SAMSUNG_EXYNOS5_DWMMC, "samsung,exynos5250-dwmmc"), };const char *fdtdec_get_compatible (enum fdt_compat_id id)
Will you be resending this series?
Regards,
Simon
Quoted 4 lines
--
1.8.0
PATCH v7 1/10 FDT: Add compatible string for DWMMC
Hi Simon,
I am not planning to resend the series untill a re-base is required.
Thanks & Regards
Amarendra reddy
Quoted 77 lines · Simon Glass
Hi Amar,
lib/fdtdec.c static const char * const compat_names[COMPAT_COUNT] =
Quoted 46 lines · Amar
Add required compatible information for DWMMC driver.
Signed-off-by Vivek Gautam <[email protected]>Signed-off-by Amar <[email protected]>Acked-by Jaehoon Chung <[email protected]>---
Changes since V1:
No change.Changes since V2:
1)Updation of commit message and resubmition of proper patch set.Changes since V3:
No change.Changes since V4:
No change.Changes since V5:
No change.include/fdtdec.h | 1 + lib/fdtdec.c | 1 + 2 files changed, 2 insertions(+)include/fdtdec.h +0
-0@@ -81,6 +81,7 @@ enum fdt_compat_id {COMPAT_SAMSUNG_EXYNOS_EHCI ,/* Exynos EHCI controller */ COMPAT_SAMSUNG_EXYNOS_USB_PHY, /* Exynos phy controller forusb2.0 */
COMPAT_MAXIM_MAX77686_PMIC, /* MAX77686 PMIC */include/fdtdec.h +1
-0+COMPAT_SAMSUNG_EXYNOS5_DWMMC ,/* Exynos5 DWMMC controller */ COMPAT_COUNT, };lib/fdtdec.c +0
-0@@ -56,6 +56,7 @@ static const char * const compat_names[COMPAT_COUNT] ={
lib/fdtdec.c static const char * const compat_names[COMPAT_COUNT] = { · line 62
Quoted 8 lines
lib/fdtdec.c +1
-0COMPAT (SAMSUNG_EXYNOS_EHCI ,"samsung,exynos-ehci" ),COMPAT (SAMSUNG_EXYNOS_USB_PHY ,"samsung,exynos-usb-phy" ),COMPAT (MAXIM_MAX77686_PMIC ,"maxim,max77686_pmic" ), + COMPAT(SAMSUNG_EXYNOS5_DWMMC, "samsung,exynos5250-dwmmc"), };const char *fdtdec_get_compatible (enum fdt_compat_id id)Will you be resending this series?
Regards,
SimonQuoted 4 lines
--
1.8.0_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
PATCH v7 2/10 EXYNOS5: FDT: Add DWMMC device node data
In reply to AmarThis patch adds DWMMC device node data for exynos5. This patch also adds binding file for DWMMC device node.
---
Changes since V1:
1)Added binding file for DWMMC device node at the location "doc/device-tree-bindings/exynos/dwmmc.txt".
2)Removed the propname 'index' from device node. 3)Prefixed the vendor name 'samsung' before propname in device node.
Changes since V2:
1)Updation of commit message and resubmition of proper patch set.
Changes since V3:
No change.
Changes since V4:
1)Updated the doc/device-tree-bindings/exynos/dwmmc.txt with more information regarding the property 'samsung,timing'. 2)Replaced the name 'dwmmc' with 'mmc'.
Changes since V5:
1)Added the 'removable' flag to mmc device node.
Changes since V6:
No change.
arch/arm/dts/exynos5250.dtsi | 31 ++++++++++++++++++ board/samsung/dts/exynos5250-smdk5250.dts | 24 ++++++++++++++ doc/device-tree-bindings/exynos/dwmmc.txt | 54 +++++++++++++++++++++++++++++++ 3 files changed, 109 insertions(+) create mode 100644 doc/device-tree-bindings/exynos/dwmmc.txt
arch/arm/dts/exynos5250.dtsi +31 -0
@@ -151,4 +151,35 @@ }; }; + mmc at 12200000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos5250-dwmmc"; + reg = <0x12200000 0x1000>; + interrupts = <0 75 0>; + }; + + mmc at 12210000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos5250-dwmmc"; + reg = <0x12210000 0x1000>; + interrupts = <0 76 0>; + }; + + mmc at 12220000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos5250-dwmmc"; + reg = <0x12220000 0x1000>; + interrupts = <0 77 0>; + }; + + mmc at 12230000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "samsung,exynos5250-dwmmc"; + reg = <0x12230000 0x1000>; + interrupts = <0 78 0>; + }; };
board/samsung/dts/exynos5250-smdk5250.dts +24 -0
@@ -30,6 +30,10 @@ spi2 = "/spi at 12d40000"; spi3 = "/spi at 131a0000"; spi4 = "/spi at 131b0000"; + mmc0 = "/mmc at 12200000"; + mmc1 = "/mmc at 12210000"; + mmc2 = "/mmc at 12220000"; + mmc3 = "/mmc at 12230000"; }; sromc at 12250000 {
@@ -66,4 +70,24 @@ compatible = "maxim,max77686_pmic"; }; }; + + mmc at 12200000 { + samsung,bus-width = <8>; + samsung,timing = <1 3 3>; + samsung,removable = <0>; + }; + + mmc at 12210000 { + status = "disabled"; + }; + + mmc at 12220000 { + samsung,bus-width = <4>; + samsung,timing = <1 2 3>; + samsung,removable = <1>; + }; + + mmc at 12230000 { + status = "disabled"; + }; };
doc/device-tree-bindings/exynos/dwmmc.txt new file +54 -0
54 lines not on this page · raw message
Signature · 1 line
1.8.0
PATCH v7 3/10 DWMMC: Initialise dwmci and resolve EMMC read write issues
In reply to AmarThis patch enumerates dwmci and set auto stop command during dwmci initialisation.
EMMC read/write is not happening in current implementation due to improper fifo size computation. Hence modified the fifo size computation to resolve EMMC read write issues.
---
Changes since V1:
1)Created the macros RX_WMARK_SHIFT and RX_WMARK_MASK in header file.
Changes since V2:
1)Updation of commit message and resubmition of proper patch set.
Changes since V3:
1)Updated to use the macro DWMCI_CTRL_SEND_AS_CCSD instead of the hard coded value (1 << 10).
Changes since V4:
1)Updated the function dwmci_send_cmd() to use get_timer() instead of using mdelay(1).
Changes since V5:
1)Updated in response to review comments.
Changes since V6:
No change.
drivers/mmc/dw_mmc.c | 25 +++++++++++++++++-------- 1 file changed, 17 insertions(+), 8 deletions(-)
drivers/mmc/dw_mmc.c +17 -8
@@ -129,13 +129,13 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,unsigned int timeout =100000 ;u32 retry =10000 ;u32 mask, ctrl; +ulong start =get_timer (0 );while (dwmci_readl (host,DWMCI_STATUS ) &DWMCI_BUSY ) { -if (timeout ==0 ) { +if (get_timer (start) > timeout) {printf ("Timeout on data busy\n" );return TIMEOUT ; } - timeout--; }dwmci_writel (host,DWMCI_RINTSTS ,DWMCI_INTMSK_ALL );
@@ -143,7 +143,6 @@ static int dwmci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,if (data)dwmci_prepare_data (host, data); -dwmci_writel (host,DWMCI_CMDARG , cmd->cmdarg);if (data)
@@ -314,7 +313,7 @@ static void dwmci_set_ios(struct mmc *mmc)static int dwmci_init (struct mmc *mmc) {struct dwmci_host *host = (struct dwmci_host *)mmc->priv; -u32 fifo_size, fifoth_val; +u32 fifo_size, fifoth_val, ier;dwmci_writel (host,DWMCI_PWREN ,1 );
@@ -323,6 +322,14 @@ static int dwmci_init(struct mmc *mmc)return -1 ; } +/* Enumerate at 400KHz */ +dwmci_setup_bus (host, mmc->f_min); + +/* Set auto stop command */ + ier =dwmci_readl (host,DWMCI_CTRL ); + ier |=DWMCI_CTRL_SEND_AS_CCSD ; +dwmci_writel (host,DWMCI_CTRL , ier); +dwmci_writel (host,DWMCI_RINTSTS ,0xFFFFFFFF );dwmci_writel (host,DWMCI_INTMASK ,0 );
@@ -332,11 +339,13 @@ static int dwmci_init(struct mmc *mmc)dwmci_writel (host,DWMCI_BMOD ,1 ); fifo_size =dwmci_readl (host,DWMCI_FIFOTH ); -if (host->fifoth_val) + fifo_size = ((fifo_size &RX_WMARK_MASK ) >>RX_WMARK_SHIFT ) +1 ; +if (host->fifoth_val) { fifoth_val = host->fifoth_val; -else - fifoth_val =MSIZE (0x2 ) |RX_WMARK (fifo_size/2 -1 ) | -TX_WMARK (fifo_size/2 ); + }else { + fifoth_val =MSIZE (0x2 ) |RX_WMARK (fifo_size /2 -1 ) | +TX_WMARK (fifo_size /2 ); + }dwmci_writel (host,DWMCI_FIFOTH , fifoth_val);dwmci_writel (host,DWMCI_CLKENA ,0 );
Signature · 1 line
1.8.0
PATCH v7 4/10 EXYNOS5: DWMMC: Added FDT support for DWMMC
In reply to AmarThis patch adds FDT support for DWMMC, by reading the DWMMC node data from the device tree and initialising DWMMC channels as per data obtained from the node.
---
Changes since V1:
1)Updated code to have same signature for the function exynos_dwmci_init() for both FDT and non-FDT versions. 2)Updated code to pass device_id parameter to the function exynos5_mmc_set_clk_div() instead of index. 3)Updated code to decode the value of "samsung,width" from FDT. 4)Channel index is computed instead of getting from FDT.
Changes since V2:
1)Updation of commit message and resubmition of proper patch set.
Changes since V3:
1)Replaced the new function exynos5_mmc_set_clk_div() with the existing function set_mmc_clk(). set_mmc_clk() will do the purpose. 2)Computation of FSYS block clock divisor (pre-ratio) is added.
Changes since V4:
1)Replaced "unsigned int exynos_dwmmc_init(int index, int bus_width)" with int exynos_dwmci_add_port(int, u32, inth, u32)
i)exynos_dwmmc_add_port() will be used by non-FDT boards. ii)In FDT case, exynos_dwmmc_init(const void *blob) will use exynos_dwmmc_add_port() for every channel enabled in device node.
2)Changed the computation method of mmc clock divisor.
3)Updated exynos_dwmmc_init() to compute the 'clksel_val' within the function.
Changes since V5:
1)Updated in response to review comments and changed the mmc clock value from 50MHz to 52MHz.
Changes since V6:
No change.
arch/arm/include/asm/arch-exynos/dwmmc.h | 11 +-- drivers/mmc/exynos_dw_mmc.c | 127 ++++++++++++++++++++++++++++--- include/dwmmc.h | 3 + 3 files changed, 124 insertions(+), 17 deletions(-)
arch/arm/include/asm/arch-exynos/dwmmc.h +4 -7
@@ -27,10 +27,7 @@#define DWMCI_SET_DRV_CLK (x) ((x) << 16)#define DWMCI_SET_DIV_RATIO (x) ((x) << 24) -int exynos_dwmci_init (u32 regbase,int bus_width,int index); - -static inline unsigned int exynos_dwmmc_init (int index,int bus_width) -{ -unsigned int base =samsung_get_base_mmc () + (0x10000 * index); -return exynos_dwmci_init (base, bus_width, index); -} +#ifdef CONFIG_OF_CONTROL +int exynos_dwmmc_init (const void *blob); +#endif +int exynos_dwmci_add_port (int index,u32 regbase,int bus_width,u32 clksel);
drivers/mmc/exynos_dw_mmc.c +117 -10
156 lines not on this page · raw message
include/dwmmc.h +3 -0
@@ -123,6 +123,8 @@#define MSIZE (x) ((x) << 28)#define RX_WMARK (x) ((x) << 16)#define TX_WMARK (x) (x) +#define RX_WMARK_SHIFT 16 +#define RX_WMARK_MASK (0xfff << RX_WMARK_SHIFT)#define DWMCI_IDMAC_OWN (1 << 31)#define DWMCI_IDMAC_CH (1 << 4)
@@ -144,6 +146,7 @@ struct dwmci_host {unsigned int bus_hz;int dev_index;int buswidth; +u32 clksel_val;u32 fifoth_val;struct mmc *mmc;
Signature · 1 line
1.8.0
PATCH v7 5/10 EXYNOS5: DWMMC: Initialise the local variable to avoid unwanted results.
In reply to AmarThis patch initialises the local variable 'shift' to zero. The uninitialised local variable 'shift' had garbage value and was resulting in unwnated results in the functions exynos5_get_mmc_clk() and exynos4_get_mmc_clk().
---
Changes since V1:
1)Updated the function exynos5_mmc_set_clk_div() to receive 'device_i'd as input parameter instead of 'index'.
Changes since V2:
1)Updation of commit message and resubmition of proper patch set.
Changes since V3:
1)Removed the new API exynos5_mmc_set_clk_div() from clock.c, because existing API set_mmc_clk() can be used to set mmc clock.
Changes since V4:
1)Updated the subject line to reflect the changes present in this patch. 2)Changes of the file arch/arm/include/asm/arch-exynos/clk.h which were present in this patch, have been moved out of this patch.
Changes since V5:
No change.
Changes since V6:
No change.
arch/arm/cpu/armv7/exynos/clock.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/cpu/armv7/exynos/clock.c +2 -2
@@ -490,7 +490,7 @@ static unsigned long exynos4_get_mmc_clk(int dev_index) (struct exynos4_clock *)samsung_get_base_clock ();unsigned long uclk, sclk;unsigned int sel, ratio, pre_ratio; -int shift; +int shift =0 ; sel =readl (&clk->src_fsys); sel = (sel >> (dev_index <<2 )) &0xf ;
@@ -539,7 +539,7 @@ static unsigned long exynos5_get_mmc_clk(int dev_index) (struct exynos5_clock *)samsung_get_base_clock ();unsigned long uclk, sclk;unsigned int sel, ratio, pre_ratio; -int shift; +int shift =0 ; sel =readl (&clk->src_fsys); sel = (sel >> (dev_index <<2 )) &0xf ;
Signature · 1 line
1.8.0
PATCH v7 6/10 SMDK5250: Initialise and Enable DWMMC, support FDT and non-FDT
In reply to AmarThis patch enables and initialises DWMMC for SMDK5250.
Supports both FDT and non-FDT. This patch creates a new file 'exynos5-dt.c' meant for FDT support.
exynos5-dt.c: This file shall contain all code which supports FDT.
Any addition of FDT support for any module needs to be added in this file.
smdk5250.c: This file shall contain the code which supports non-FDT.
version. Any addition of non-FDT support for any module needs to be added in this file.
May be, the file smdk5250.c can be removed in near future when non-FDT is not required.
The Makefile is updated to compile only one of the files exynos5-dt.c / smdk5250.c based on FDT configuration.
NOTE:
Please note that all additions corresponding to FDT need to be added into the file exynos5-dt.c.
At same time if non-FDT support is required then add the corresponding updations into smdk5250.c.
---
Changes since V1:
1)A new file 'exynos5-dt.c' is created meant for FDT support 2)Makefile is updated to compile only one of the files exynos5-dt.c / smdk5250.c based on FDT configuration
Changes since V2:
1)Updation of commit message and resubmition of proper patch set.
Changes since V3:
No change.
Changes since V4:
1)Replaced the function call 'exynos_dwmmc_init(0, 8);' with the function exynos_dwmmc_add_port() in smdk5250.c. 2)dram_init() is updated to use for loop to compute the ram size. 3)dram_init_banksize() is updated to use for loop to initialise the dram bank size.
4)board_uart_init() is updated to use for loop to initialise UARTS. 5)In non-FDT case NULL is passed as parameter to board_i2c_init().
Changes since V5:
1)Enabled CONFIG_LCD only for non-FDT operation.
Changes since V6:
1)Re-based. --- board/samsung/smdk5250/Makefile | 4 + board/samsung/smdk5250/exynos5-dt.c | 339 ++++++++++++++++++++++++++++++++++++ board/samsung/smdk5250/smdk5250.c | 165 ++++++------------ include/configs/exynos5250-dt.h | 8 + 4 files changed, 406 insertions(+), 110 deletions(-) create mode 100644 board/samsung/smdk5250/exynos5-dt.c
board/samsung/smdk5250/Makefile +4 -0
@@ -32,8 +32,12 @@ COBJS += tzpc_init.o COBJS += smdk5250_spl.o ifndef CONFIG_SPL_BUILD +ifdef CONFIG_OF_CONTROL +COBJS += exynos5-dt.o +else COBJS += smdk5250.o endif +endif ifdef CONFIG_SPL_BUILD COBJS += spl_boot.o
board/samsung/smdk5250/exynos5-dt.c new file +339 -0
339 lines not on this page · raw message
board/samsung/smdk5250/smdk5250.c +55 -110
221 lines not on this page · raw message
include/configs/exynos5250-dt.h +8 -0
@@ -95,6 +95,8 @@#define CONFIG_MMC #define CONFIG_SDHCI #define CONFIG_S5P_SDHCI +#define CONFIG_DWMMC +#define CONFIG_EXYNOS_DWMMC #define CONFIG_BOARD_EARLY_INIT_F
@@ -210,6 +212,10 @@#define CONFIG_DOS_PARTITION +#define CONFIG_EFI_PARTITION +#define CONFIG_CMD_PART +#define CONFIG_PARTITION_UUIDS +#define CONFIG_IRAM_STACK 0x02050000#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000)
@@ -309,6 +315,7 @@#define CONFIG_SHA256 /* Display */ +#ifndef CONFIG_OF_CONTROL #define CONFIG_LCD #ifdef CONFIG_LCD #define CONFIG_EXYNOS_FB
@@ -317,5 +324,6 @@#define LCD_YRES 1600#define LCD_BPP LCD_COLOR16#endif +#endif #endif /* __CONFIG_H */
Signature · 1 line
1.8.0
PATCH v7 7/10 MMC: APIs to support resize of EMMC boot partition
In reply to AmarThis patch adds APIs to access(open / close) and to resize boot partiton of EMMC.
---
Changes since V1:
New patch.
Changes since V2:
1)Updation of commit message and resubmition of proper patch set.
Changes since V3:
No change.
Changes since V4:
1)Replaced the functions mmc_boot_open() & mmc_boot_close() with a single function mmc_boot_part_access().
Changes since V5:
1)Updated in response to review comments.
Changes since V6:
1)Added spaces around << operator, in response to review comments.
drivers/mmc/mmc.c | 132 ++++++++++++++++++++++++++++++++++++++++++++++++++++++ include/mmc.h | 26 +++++++++++ 2 files changed, 158 insertions(+)
drivers/mmc/mmc.c +132 -0
@@ -1327,3 +1327,135 @@ int mmc_initialize(bd_t *bis)return 0 ; } + +/* +* This function changes the size of boot partition and the size of rpmb +* partition present on EMMC devices. +* +* Input Parameters: +* struct *mmc: pointer for the mmc device strcuture +* bootsize: size of boot partition +* rpmbsize: size of rpmb partition +* +* Returns 0 on success. +*/ + +int mmc_boot_partition_size_change (struct mmc *mmc,unsigned long bootsize, +unsigned long rpmbsize) +{ +int err; +struct mmc_cmd cmd; + +/* Only use this command for raw EMMC moviNAND. Enter backdoor mode */ + cmd.cmdidx =MMC_CMD_RES_MAN ; + cmd.resp_type = MMC_RSP_R1b; + cmd.cmdarg =MMC_CMD62_ARG1 ; + + err =mmc_send_cmd (mmc, &cmd,NULL ); +if (err) { +debug ("mmc_boot_partition_size_change: Error1 = %d\n" , err); +return err; + } + +/* Boot partition changing mode */ + cmd.cmdidx =MMC_CMD_RES_MAN ; + cmd.resp_type = MMC_RSP_R1b; + cmd.cmdarg =MMC_CMD62_ARG2 ; + + err =mmc_send_cmd (mmc, &cmd,NULL ); +if (err) { +debug ("mmc_boot_partition_size_change: Error2 = %d\n" , err); +return err; + } +/* boot partition size is multiple of 128KB */ + bootsize = (bootsize *1024 ) /128 ; + +/* Arg: boot partition size */ + cmd.cmdidx =MMC_CMD_RES_MAN ; + cmd.resp_type = MMC_RSP_R1b; + cmd.cmdarg = bootsize; + + err =mmc_send_cmd (mmc, &cmd,NULL ); +if (err) { +debug ("mmc_boot_partition_size_change: Error3 = %d\n" , err); +return err; + } +/* RPMB partition size is multiple of 128KB */ + rpmbsize = (rpmbsize *1024 ) /128 ; +/* Arg: RPMB partition size */ + cmd.cmdidx =MMC_CMD_RES_MAN ; + cmd.resp_type = MMC_RSP_R1b; + cmd.cmdarg = rpmbsize; + + err =mmc_send_cmd (mmc, &cmd,NULL ); +if (err) { +debug ("mmc_boot_partition_size_change: Error4 = %d\n" , err); +return err; + } +return 0 ; +} + +/* +* This function shall form and send the commands to open / close the +* boot partition specified by user. +* +* Input Parameters: +* ack: 0x0 - No boot acknowledge sent (default) +* 0x1 - Boot acknowledge sent during boot operation +* part_num: User selects boot data that will be sent to master +* 0x0 - Device not boot enabled (default) +* 0x1 - Boot partition 1 enabled for boot +* 0x2 - Boot partition 2 enabled for boot +* access: User selects partitions to access +* 0x0 : No access to boot partition (default) +* 0x1 : R/W boot partition 1 +* 0x2 : R/W boot partition 2 +* 0x3 : R/W Replay Protected Memory Block (RPMB) +* +* Returns 0 on success. +*/ +int mmc_boot_part_access (struct mmc *mmc,u32 ack,u32 part_num,u32 access) +{ +int err; +struct mmc_cmd cmd; + +/* Boot ack enable, boot partition enable , boot partition access */ + cmd.cmdidx =MMC_CMD_SWITCH ; + cmd.resp_type = MMC_RSP_R1b; + + cmd.cmdarg = (MMC_SWITCH_MODE_WRITE_BYTE <<24 ) | + (EXT_CSD_PART_CONF <<16 ) | + ((EXT_CSD_BOOT_ACK (ack) | +EXT_CSD_BOOT_PART_NUM (part_num) | +EXT_CSD_PARTITION_ACCESS (access)) <<8 ); + + err =mmc_send_cmd (mmc, &cmd,NULL ); +if (err) { +if (access) { +debug ("mmc boot partition#%d open failure:" +"Error1 = %d\n" , part_num, err); + }else { +debug ("mmc boot partition#%d close failure:" +"Error = %d\n" , part_num, err); + } +return err; + } + +if (access) { +/* 4bit transfer mode@booting time. */ + cmd.cmdidx =MMC_CMD_SWITCH ; + cmd.resp_type = MMC_RSP_R1b; + + cmd.cmdarg = (MMC_SWITCH_MODE_WRITE_BYTE <<24 ) | + (EXT_CSD_BOOT_BUS_WIDTH <<16 ) | + ((1 <<0 ) <<8 ); + + err =mmc_send_cmd (mmc, &cmd,NULL ); +if (err) { +debug ("mmc boot partition#%d open failure:" +"Error2 = %d\n" , part_num, err); +return err; + } + } +return 0 ; +}
include/mmc.h +26 -0
@@ -86,6 +86,11 @@#define MMC_CMD_APP_CMD 55#define MMC_CMD_SPI_READ_OCR 58#define MMC_CMD_SPI_CRC_ON_OFF 59 +#define MMC_CMD_RES_MAN 62 + +#define MMC_CMD62_ARG1 0xefac62ec +#define MMC_CMD62_ARG2 0xcbaea7 +#define SD_CMD_SEND_RELATIVE_ADDR 3#define SD_CMD_SWITCH_FUNC 6
@@ -153,6 +158,7 @@*/ #define EXT_CSD_PARTITIONING_SUPPORT 160/* RO */ #define EXT_CSD_ERASE_GROUP_DEF 175/* R/W */ +#define EXT_CSD_BOOT_BUS_WIDTH 177#define EXT_CSD_PART_CONF 179/* R/W */ #define EXT_CSD_BUS_WIDTH 183/* R/W */ #define EXT_CSD_HS_TIMING 185/* R/W */
@@ -177,6 +183,16 @@#define EXT_CSD_BUS_WIDTH_4 1/* Card is in 4 bit mode */ #define EXT_CSD_BUS_WIDTH_8 2/* Card is in 8 bit mode */ +#define EXT_CSD_BOOT_ACK_ENABLE (1 << 6) +#define EXT_CSD_BOOT_PARTITION_ENABLE (1 << 3) +#define EXT_CSD_PARTITION_ACCESS_ENABLE (1 << 0) +#define EXT_CSD_PARTITION_ACCESS_DISABLE (0 << 0) + +#define EXT_CSD_BOOT_ACK (x) (x << 6) +#define EXT_CSD_BOOT_PART_NUM (x) (x << 3) +#define EXT_CSD_PARTITION_ACCESS (x) (x << 0) + +#define R1_ILLEGAL_COMMAND (1 << 22)#define R1_APP_CMD (1 << 5)
@@ -201,6 +217,11 @@#define PART_ACCESS_MASK (0x7)#define PART_SUPPORT (0x1) +/* The number of MMC physical partitions. These consist of: +* boot partitions (2), general purpose partitions (4) in MMC v4.4. +*/ +#define MMC_NUM_BOOT_PARTITION 2 +struct mmc_cid {unsigned long psn;unsigned short oid;
@@ -275,6 +296,11 @@ int board_mmc_getcd(struct mmc *mmc);int mmc_switch_part (int dev_num,unsigned int part_num);int mmc_getcd (struct mmc *mmc);void spl_mmc_load (void )__noreturn ; +/* Function to change the size of boot partition and rpmb partitions */ +int mmc_boot_partition_size_change (struct mmc *mmc,unsigned long bootsize, +unsigned long rpmbsize); +/* Function to send commands to open/close the specified boot partition */ +int mmc_boot_part_access (struct mmc *mmc,u32 ack,u32 part_num,u32 access);#ifdef CONFIG_GENERIC_MMC #define mmc_host_is_spi (mmc) ((mmc)->host_caps & MMC_MODE_SPI)
Signature · 1 line
1.8.0
PATCH v7 7/10 MMC: APIs to support resize of EMMC boot partition
Dear Amar,
Quoted 1 line · In message <[email protected]> you…
This patch adds APIs to access(open / close) and to resize boot partiton of EMMC.
Can you please make this code conditional, so only boards that want this feature (and actually use EMMC) suffer from the increased memory footprint?
Thanks.
Viele Gr??e,
Wolfgang Denk
Signature · 6 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de The price of success is hard work, dedication to the job at hand, and the determination that whether we win or lose, we have applied the best of ourselves to the task at hand. - Vince Lombardi
PATCH v7 7/10 MMC: APIs to support resize of EMMC boot partition
Dear Wolfgang,
Thank you for the comments.
Ok, I will make this code conditional.
I will prepare a new patch and post the same.
Thanks & Regards
Amarendra
Quoted 29 lines · Wolfgang Denk
Dear Amar,
In message <[email protected]>
Quoted 1 line · you
This patch adds APIs to access(open / close) and to resize boot partiton
of EMMC.
Can you please make this code conditional, so only boards that want this feature (and actually use EMMC) suffer from the increased memory footprint?
Thanks.
Viele Gr??e,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de The price of success is hard work, dedication to the job at hand, and the determination that whether we win or lose, we have applied the
best of ourselves to the task at hand. - Vince Lombardi
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
PATCH v7 7/10 MMC: APIs to support resize of EMMC boot partition
Quoted 3 lines · Amarendra Reddy
Dear Wolfgang,
Thank you for the comments.
Ok, I will make this code conditional.
please don't top posting.
Quoted 1 line
I will prepare a new patch and post the same.
Do you have a plan to resend?
Quoted 38 lines
Thanks & Regards
AmarendraQuoted 17 lines · Wolfgang Denk
Dear Amar,
In message <[email protected]>
Quoted 1 line · you
This patch adds APIs to access(open / close) and to resize boot partiton
of EMMC.
Can you please make this code conditional, so only boards that want this feature (and actually use EMMC) suffer from the increased memory footprint?
Thanks.
Viele Gr??e,
Wolfgang Denk
Quoted 12 lines
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de The price of success is hard work, dedication to the job at hand, and the determination that whether we win or lose, we have applied the
best of ourselves to the task at hand. - Vince Lombardi
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Quoted 5 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Thanks,
Minkyu Kang.
PATCH v7 7/10 MMC: APIs to support resize of EMMC boot partition
Dear Minkyu,
I have plans to send a new patch to 'make this code conditional'. But it will be a new patch.
I am planning to take up this activity after the V7 patchset is merged into mainline.
All patches of V7 patchset have been ACKED.
On top, DWMMC patchset is long pending, and any changes will further cause delay.
Please provide your comments.
Thanks & Regards
Amarendra Reddy
Quoted 59 lines · Minkyu Kang
Quoted 3 lines · Amarendra Reddy
Dear Wolfgang,
Thank you for the comments.
Ok, I will make this code conditional.please don't top posting.
Quoted 1 line
I will prepare a new patch and post the same.
Do you have a plan to resend?
Quoted 11 lines
Thanks & Regards
AmarendraQuoted 5 lines · Wolfgang Denk
Dear Amar,
In message <[email protected]>
Quoted 1 line · you
This patch adds APIs to access(open / close) and to resize boot
partiton
Quoted 27 lines
Quoted 12 lines
of EMMC.
Can you please make this code conditional, so only boards that want this feature (and actually use EMMC) suffer from the increased memory footprint?
Thanks.
Viele Gr??e,
Wolfgang Denk
Quoted 12 lines
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de The price of success is hard work, dedication to the job at hand, and the determination that whether we win or lose, we have applied the
best of ourselves to the task at hand. - Vince Lombardi
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-bootQuoted 5 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-bootThanks,
Minkyu Kang.
PATCH v7 7/10 MMC: APIs to support resize of EMMC boot partition
Dear Amarendra Reddy,
Quoted 4 lines · Amarendra Reddy
Dear Minkyu,
I have plans to send a new patch to 'make this code conditional'. But it will be a new patch.
I always said to you.
Please DO NOT top posting... please.
Quoted 2 lines
I am planning to take up this activity after the V7 patchset is merged into mainline.
It's OK.
Quoted 3 lines
All patches of V7 patchset have been ACKED.
On top, DWMMC patchset is long pending, and any changes will further cause delay. Please provide your comments.
please check my comments, patch 8 and 10.
Quoted 55 lines
Thanks & Regards
Amarendra ReddyOn 28 March 2013 13:48, Minkyu Kang <mk7.kang at samsung.com <mailto:[email protected]>> wrote:
On 07/03/13 18:26, Amarendra Reddy wrote: > Dear Wolfgang, > Thank you for the comments. > Ok, I will make this code conditional. please don't top posting. > I will prepare a new patch and post the same. Do you have a plan to resend? > > Thanks & Regards > Amarendra > > On 6 March 2013 02:13, Wolfgang Denk <wd at denx.de <mailto:[email protected]>> wrote: > >> Dear Amar, >> >> In message <1362489090-7745-8-git-send-email-amarendra.xt at samsung.com <mailto:[email protected]>> >> you wrote: >>> This patch adds APIs to access(open / close) and to resize boot partiton >> of EMMC. >> >> Can you please make this code conditional, so only boards that want >> this feature (and actually use EMMC) suffer from the increased memory >> footprint? >> >> Thanks. >> >> Viele Gr??e, >> >> Wolfgang Denk >> >> -- >> DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel >> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany >> Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de <mailto:[email protected]> >> The price of success is hard work, dedication to the job at hand, and >> the determination that whether we win or lose, we have applied the >> best of ourselves to the task at hand. - Vince Lombardi >> _______________________________________________ >> U-Boot mailing list >> U-Boot at lists.denx.de <mailto:[email protected]> >> http://lists.denx.de/mailman/listinfo/u-boot >> > > >
Quoted 10 lines
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de <mailto:[email protected]>
> http://lists.denx.de/mailman/listinfo/u-boot
>
Thanks,
Minkyu Kang.Thanks,
Minkyu Kang.
PATCH v7 8/10 SMDK5250: Enable EMMC booting
In reply to AmarThis patch adds support for EMMC booting on SMDK5250.
---
Changes since V1:
1)Updated spl_boot.c file to maintain irom pointer table instead of using the #define values defined in header file.
Changes since V2:
1)Updation of commit message and resubmition of proper patch set.
Changes since V3:
No change.
Changes since V4:
1)The function get_irom_func(int index) has been added to avoid type casting at many places.
2)The changes to file arch/arm/include/asm/arch-exynos/clk.h are included in this patch file.
Changes since V5:
No change.
Changes since V6:
No change.
arch/arm/include/asm/arch-exynos/clk.h | 3 ++ board/samsung/smdk5250/clock_init.c | 15 ++++++++++ board/samsung/smdk5250/clock_init.h | 5 ++++ board/samsung/smdk5250/spl_boot.c | 52 ++++++++++++++++++++++++++++++---- 4 files changed, 69 insertions(+), 6 deletions(-)
arch/arm/include/asm/arch-exynos/clk.h +3 -0
@@ -29,6 +29,9 @@#define VPLL 4#define BPLL 5 +#define FSYS1_MMC0_DIV_MASK 0xff0f +#define FSYS1_MMC0_DIV_VAL 0x0701 +unsigned long get_pll_clk (int pllreg);unsigned long get_arm_clk (void );unsigned long get_i2c_clk (void );
board/samsung/smdk5250/clock_init.c +15 -0
@@ -28,6 +28,7 @@#include <asm/arch/clk.h> #include <asm/arch/clock.h> #include <asm/arch/spl.h> +#include <asm/arch/dwmmc.h> #include "clock_init.h" #include "setup.h"
@@ -664,3 +665,17 @@ void clock_init_dp_clock(void)/* We run DP at 267 Mhz */ setbits_le32 (&clk->div_disp1_0,CLK_DIV_DISP1_0_FIMD1 ); } + +/* +* Set clock divisor value for booting from EMMC. +* Set DWMMC channel-0 clk div to operate mmc0 device at 50MHz. +*/ +void emmc_boot_clk_div_set (void ) +{ +struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE ; +unsigned int div_mmc; + + div_mmc =readl ((unsigned int ) &clk->div_fsys1) & ~FSYS1_MMC0_DIV_MASK ; + div_mmc |=FSYS1_MMC0_DIV_VAL ; +writel (div_mmc, (unsigned int ) &clk->div_fsys1); +}
board/samsung/smdk5250/clock_init.h +5 -0
@@ -146,4 +146,9 @@ struct mem_timings *clock_get_mem_timings(void);* Initialize clock for the device */ void system_clock_init (void ); + +/* +* Set clock divisor value for booting from EMMC. +*/ +void emmc_boot_clk_div_set (void );#endif
board/samsung/smdk5250/spl_boot.c +46 -6
84 lines not on this page · raw message
Signature · 1 line
1.8.0
PATCH v7 8/10 SMDK5250: Enable EMMC booting
Dear Amar,
Quoted 38 lines · Amar
This patch adds support for EMMC booting on SMDK5250.
Signed-off-by Amar <[email protected]>Acked-by Simon Glass <[email protected]>---
Changes since V1:
1)Updatedspl_boot.cfile to maintain irom pointer table instead of using the #define values defined in header file.Changes since V2:
1)Updation of commit message and resubmition of proper patch set.Changes since V3:
No change.Changes since V4:
1)The functionget_irom_func(int index)has been added to avoid type casting at many places.
2)The changes to filearch/arm/include/asm/arch-exynos/clk.hare included in this patch file.Changes since V5:
No change.Changes since V6:
No change.arch/arm/include/asm/arch-exynos/clk.h | 3 ++ board/samsung/smdk5250/clock_init.c | 15 ++++++++++ board/samsung/smdk5250/clock_init.h | 5 ++++ board/samsung/smdk5250/spl_boot.c | 52 ++++++++++++++++++++++++++++++---- 4 files changed, 69 insertions(+), 6 deletions(-)arch/arm/include/asm/arch-exynos/clk.h +0
-0
arch/arm/include/asm/arch-exynos/clk.h line 33
Quoted 5 lines
arch/arm/include/asm/arch-exynos/clk.h +2
-0@@ -29,6 +29,9 @@#define VPLL 4#define BPLL 5 +#define FSYS1_MMC0_DIV_MASK 0xff0f +#define FSYS1_MMC0_DIV_VAL 0x0701
I think, these values are not generic.
please keep these values locally.
Quoted 129 lines
arch/arm/include/asm/arch-exynos/clk.h +1
-0+unsigned long get_pll_clk (int pllreg);unsigned long get_arm_clk (void );unsigned long get_i2c_clk (void );board/samsung/smdk5250/clock_init.c +15
-0@@ -28,6 +28,7 @@#include <asm/arch/clk.h> #include <asm/arch/clock.h> #include <asm/arch/spl.h> +#include <asm/arch/dwmmc.h> #include "clock_init.h" #include "setup.h" @@ -664,3 +665,17 @@ void clock_init_dp_clock(void)/* We run DP at 267 Mhz */ setbits_le32 (&clk->div_disp1_0,CLK_DIV_DISP1_0_FIMD1 ); } + +/* +* Set clock divisor value for booting from EMMC. +* Set DWMMC channel-0 clk div to operate mmc0 device at 50MHz. +*/ +void emmc_boot_clk_div_set (void ) +{ +struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE ; +unsigned int div_mmc; + + div_mmc =readl ((unsigned int ) &clk->div_fsys1) & ~FSYS1_MMC0_DIV_MASK ; + div_mmc |=FSYS1_MMC0_DIV_VAL ; +writel (div_mmc, (unsigned int ) &clk->div_fsys1); +}board/samsung/smdk5250/clock_init.h +5
-0@@ -146,4 +146,9 @@ struct mem_timings *clock_get_mem_timings(void);* Initialize clock for the device */ void system_clock_init (void ); + +/* +* Set clock divisor value for booting from EMMC. +*/ +void emmc_boot_clk_div_set (void );#endif board/samsung/smdk5250/spl_boot.c +39
-6@@ -23,15 +23,42 @@#include <common.h> #include <config.h> +#include <asm/arch-exynos/dmc.h> +#include <asm/arch/clock.h> +#include <asm/arch/clk.h> + +#include "clock_init.h" + +/* Index into irom ptr table */ +enum index { +MMC_INDEX , +EMMC44_INDEX , +EMMC44_END_INDEX , +SPI_INDEX , +}; + +/* IROM Function Pointers Table */ +u32 irom_ptr_table[] = { + [MMC_INDEX ] =0x02020030 ,/* iROM Function Pointer-SDMMC boot */ + [EMMC44_INDEX ] =0x02020044 ,/* iROM Function Pointer-EMMC4.4 boot*/ + [EMMC44_END_INDEX ] =0x02020048 ,/* iROM Function Pointer +-EMMC4.4 end boot operation */ + [SPI_INDEX ] =0x02020058 ,/* iROM Function Pointer-SPI boot */ + }; +enum boot_mode {BOOT_MODE_MMC =4 ,BOOT_MODE_SERIAL =20 , +BOOT_MODE_EMMC =8 ,/* EMMC4.4 */ /* Boot based on Operating Mode pin settings */ BOOT_MODE_OM =32 ,BOOT_MODE_USB ,/* Boot using USB download */ }; -typedef u32 (*spi_copy_func_t )(u32 offset,u32 nblock,u32 dst); +void *get_irom_func (int index) +{ +return (void *) *(u32 *)irom_ptr_table[index]; +}/* * Copy U-boot from mmc to RAM: @@ -40,23 +67,36 @@ enum boot_mode {*/ void copy_uboot_to_ram (void ) { -spi_copy_func_t spi_copy;enum boot_mode bootmode; -u32 (*copy_bl2)(u32, u32, u32); - +u32 (*spi_copy)(u32 offset,u32 nblock,u32 dst); +u32 (*copy_bl2)(u32 offset,u32 nblock,u32 dst); +u32 (*copy_bl2_from_emmc)(u32 nblock,u32 dst); +void (*end_bootop_from_emmc)(void ); +/* read Operation Mode ststus register to find the bootmode */ bootmode =readl (EXYNOS5_POWER_BASE ) &OM_STAT ;switch (bootmode) {case BOOT_MODE_SERIAL : - spi_copy = *(spi_copy_func_t *)EXYNOS_COPY_SPI_FNPTR_ADDR ; + spi_copy =get_irom_func (SPI_INDEX );spi_copy (SPI_FLASH_UBOOT_POS ,CONFIG_BL2_SIZE ,CONFIG_SYS_TEXT_BASE );break ;case BOOT_MODE_MMC : - copy_bl2 = (void *) *(u32 *)COPY_BL2_FNPTR_ADDR ; + copy_bl2 =get_irom_func (MMC_INDEX );copy_bl2 (BL2_START_OFFSET ,BL2_SIZE_BLOC_COUNT ,CONFIG_SYS_TEXT_BASE );break ; +case BOOT_MODE_EMMC : +/* Set the FSYS1 clock divisor value for EMMC boot */ +emmc_boot_clk_div_set (); +
board/samsung/smdk5250/spl_boot.c enum boot_mode { · line 102
Quoted 10 lines
board/samsung/smdk5250/spl_boot.c +7
-0+ copy_bl2_from_emmc =get_irom_func (EMMC44_INDEX ); + end_bootop_from_emmc =get_irom_func (EMMC44_END_INDEX ); + +copy_bl2_from_emmc (BL2_SIZE_BLOC_COUNT ,CONFIG_SYS_TEXT_BASE ); +end_bootop_from_emmc (); +break ; +default :break ; }
Thanks,
Minkyu Kang.
PATCH v7 8/10 SMDK5250: Enable EMMC booting
Dear Minkyu,
Ok, I will keep these valuse locally.
Thanks & Regards
Amarendra Reddy
Quoted 209 lines · Minkyu Kang
Dear Amar,
Quoted 24 lines · Amar
This patch adds support for EMMC booting on SMDK5250.
Signed-off-by Amar <[email protected]>Acked-by Simon Glass <[email protected]>---
Changes since V1:
1)Updatedspl_boot.cfile to maintain irom pointer table instead of using the #define values defined in header file.Changes since V2:
1)Updation of commit message and resubmition of proper patch set.Changes since V3:
No change.Changes since V4:
1)The functionget_irom_func(int index)has been added to avoid type casting at many places.
2)The changes to filearch/arm/include/asm/arch-exynos/clk.hare included in this patch file.Changes since V5:
No change.Quoted 7 lines
Changes since V6:
No change.arch/arm/include/asm/arch-exynos/clk.h | 3 ++ board/samsung/smdk5250/clock_init.c | 15 ++++++++++ board/samsung/smdk5250/clock_init.h | 5 ++++ board/samsung/smdk5250/spl_boot.c | 52++++++++++++++++++++++++++++++----
Review
Quoted 3 lines
4 files changed, 69 insertions(+), 6 deletions(-)(quoted diff) +0
-0
b/arch/arm/include/asm/arch-exynos/clk.harch/arm/include/asm/arch-exynos/clk.h line 33
Quoted 9 lines
index 1935b0b..a4d5b4e 100644
arch/arm/include/asm/arch-exynos/clk.h +2
-0@@ -29,6 +29,9 @@#define VPLL 4#define BPLL 5 +#define FSYS1_MMC0_DIV_MASK 0xff0f +#define FSYS1_MMC0_DIV_VAL 0x0701I think, these values are not generic.
please keep these values locally.Review
Quoted 5 lines
arch/arm/include/asm/arch-exynos/clk.h +1
-0+unsigned long get_pll_clk (int pllreg);unsigned long get_arm_clk (void );unsigned long get_i2c_clk (void );(quoted diff) +0
-0
b/board/samsung/smdk5250/clock_init.cQuoted 13 lines
index c009ae5..154993c 100644
board/samsung/smdk5250/clock_init.c +1
-0@@ -28,6 +28,7 @@#include <asm/arch/clk.h> #include <asm/arch/clock.h> #include <asm/arch/spl.h> +#include <asm/arch/dwmmc.h> #include "clock_init.h" #include "setup.h" @@ -664,3 +665,17 @@ void clock_init_dp_clock(void)/* We run DP at 267 Mhz */ board/samsung/smdk5250/clock_init.c void clock_init_dp_clock(void) · line 675
Quoted 10 lines
board/samsung/smdk5250/clock_init.c +8
-0setbits_le32 (&clk->div_disp1_0,CLK_DIV_DISP1_0_FIMD1 ); } + +/* +* Set clock divisor value for booting from EMMC. +* Set DWMMC channel-0 clk div to operate mmc0 device at 50MHz. +*/ +void emmc_boot_clk_div_set (void ) +{ + struct exynos5_clock *clk = (struct exynos5_clock*)EXYNOS5_CLOCK_BASE;
board/samsung/smdk5250/clock_init.c void clock_init_dp_clock(void)
Quoted 3 lines
board/samsung/smdk5250/clock_init.c +3
-0+unsigned int div_mmc; + + div_mmc = readl((unsigned int) &clk->div_fsys1) &~FSYS1_MMC0_DIV_MASK;
Review
Quoted 4 lines
board/samsung/smdk5250/clock_init.c +3
-0+ div_mmc |=FSYS1_MMC0_DIV_VAL ; +writel (div_mmc, (unsigned int ) &clk->div_fsys1); +}(quoted diff) +0
-0
b/board/samsung/smdk5250/clock_init.hReview
Quoted 14 lines
index f751bcb..20a1d47 100644
board/samsung/smdk5250/clock_init.h +5
-0@@ -146,4 +146,9 @@ struct mem_timings *clock_get_mem_timings(void);* Initialize clock for the device */ void system_clock_init (void ); + +/* +* Set clock divisor value for booting from EMMC. +*/ +void emmc_boot_clk_div_set (void );#endif (quoted diff) +0
-0
b/board/samsung/smdk5250/spl_boot.cQuoted 14 lines
index d8f3c1e..4ddbd4a 100644
board/samsung/smdk5250/spl_boot.c +7
-0@@ -23,15 +23,42 @@#include <common.h> #include <config.h> +#include <asm/arch-exynos/dmc.h> +#include <asm/arch/clock.h> +#include <asm/arch/clk.h> + +#include "clock_init.h" + +/* Index into irom ptr table */ board/samsung/smdk5250/spl_boot.c line 42
Quoted 10 lines
board/samsung/smdk5250/spl_boot.c +10
-0+enum index { +MMC_INDEX , +EMMC44_INDEX , +EMMC44_END_INDEX , +SPI_INDEX , +}; + +/* IROM Function Pointers Table */ +u32 irom_ptr_table[] = { + [MMC_INDEX ] =0x02020030 ,/* iROM Function Pointer-SDMMC boot */
board/samsung/smdk5250/spl_boot.c line 43
Quoted 1 line
board/samsung/smdk5250/spl_boot.c +1
-0+ [EMMC44_INDEX] = 0x02020044, /* iROM Function Pointer-EMMC4.4boot*/
board/samsung/smdk5250/spl_boot.c line 45
Quoted 2 lines
board/samsung/smdk5250/spl_boot.c +2
-0+ [EMMC44_END_INDEX] = 0x02020048,/* iROM Function Pointer +-EMMC4.4 end boot operation */
board/samsung/smdk5250/spl_boot.c line 46
Quoted 1 line
board/samsung/smdk5250/spl_boot.c +1
-0+ [SPI_INDEX] = 0x02020058, /* iROM Function Pointer-SPI boot*/
Quoted 45 lines
board/samsung/smdk5250/spl_boot.c +14
-6+ }; +enum boot_mode {BOOT_MODE_MMC =4 ,BOOT_MODE_SERIAL =20 , +BOOT_MODE_EMMC =8 ,/* EMMC4.4 */ /* Boot based on Operating Mode pin settings */ BOOT_MODE_OM =32 ,BOOT_MODE_USB ,/* Boot using USB download */ }; -typedef u32 (*spi_copy_func_t )(u32 offset,u32 nblock,u32 dst); +void *get_irom_func (int index) +{ +return (void *) *(u32 *)irom_ptr_table[index]; +}/* * Copy U-boot from mmc to RAM: @@ -40,23 +67,36 @@ enum boot_mode {*/ void copy_uboot_to_ram (void ) { -spi_copy_func_t spi_copy;enum boot_mode bootmode; -u32 (*copy_bl2)(u32, u32, u32); - +u32 (*spi_copy)(u32 offset,u32 nblock,u32 dst); +u32 (*copy_bl2)(u32 offset,u32 nblock,u32 dst); +u32 (*copy_bl2_from_emmc)(u32 nblock,u32 dst); +void (*end_bootop_from_emmc)(void ); +/* read Operation Mode ststus register to find the bootmode */ bootmode =readl (EXYNOS5_POWER_BASE ) &OM_STAT ;switch (bootmode) {case BOOT_MODE_SERIAL : - spi_copy = *(spi_copy_func_t *)EXYNOS_COPY_SPI_FNPTR_ADDR ; + spi_copy =get_irom_func (SPI_INDEX );spi_copy (SPI_FLASH_UBOOT_POS ,CONFIG_BL2_SIZE ,CONFIG_SYS_TEXT_BASE );break ;case BOOT_MODE_MMC : - copy_bl2 = (void *) *(u32 *)COPY_BL2_FNPTR_ADDR ; + copy_bl2 =get_irom_func (MMC_INDEX ); copy_bl2(BL2_START_OFFSET, BL2_SIZE_BLOC_COUNT,board/samsung/smdk5250/spl_boot.c enum boot_mode { · line 96
Quoted 10 lines
board/samsung/smdk5250/spl_boot.c +8
-0CONFIG_SYS_TEXT_BASE);break ; +case BOOT_MODE_EMMC : +/* Set the FSYS1 clock divisor value for EMMC boot */ +emmc_boot_clk_div_set (); + + copy_bl2_from_emmc =get_irom_func (EMMC44_INDEX ); + end_bootop_from_emmc =get_irom_func (EMMC44_END_INDEX ); + + copy_bl2_from_emmc(BL2_SIZE_BLOC_COUNT,
CONFIG_SYS_TEXT_BASE);board/samsung/smdk5250/spl_boot.c enum boot_mode { · line 102
Quoted 7 lines
board/samsung/smdk5250/spl_boot.c +3
-0+end_bootop_from_emmc (); +break ; +default :break ; }Thanks,
Minkyu Kang.
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
PATCH v7 9/10 COMMON: MMC: Command to support EMMC booting and to resize EMMC boot partition
In reply to AmarThis patch adds commands to access(open/close) and resize boot partitions on EMMC.
---
Changes since V1:
1)Combined the common piece of code between 'open' and 'close' operations.
Changes since V2:
1)Updation of commit message and resubmition of proper patch set.
Changes since V3:
No change.
Changes since V4:
1)Added a new funtion boot_part_access() to combine the common parts of 'mmc open' and 'mmc close' functionalities.
2)Used the generic function "mmc_boot_part_access()" instead of two functions "mmc_boot_open()" and "mmc_boot_close()". By doing so user can specify which boot partition to be accessed (opened / closed).
Changes since V5:
1)Updated minor nits in response to review comments.
Changes since V6:
No change.
common/cmd_mmc.c | 98 +++++++++++++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 97 insertions(+), 1 deletion(-)
common/cmd_mmc.c +97 -1
@@ -147,6 +147,31 @@ U_BOOT_CMD("- display info of the current MMC device" ); +static int boot_part_access (struct mmc *mmc,u32 ack,u32 part_num,u32 access) +{ +int err; + err =mmc_boot_part_access (mmc, ack, part_num, access); + +if ((err ==0 ) && (access !=0 )) { +printf ("\t\t\t!!!Notice!!!\n" ); +printf ("!You must close EMMC boot Partition after all" +"images are written\n" ); +printf ("!EMMC boot partition has continuity at image" +"writing time.\n" ); +printf ("!So, do not close the boot partition before all" +"images are written.\n" ); +return 0 ; + }else if ((err ==0 ) && (access ==0 )) +return 0 ; +else if ((err !=0 ) && (access !=0 )) { +printf ("EMMC boot partition-%d OPEN Failed.\n" , part_num); +return 1 ; + }else { +printf ("EMMC boot partition-%d CLOSE Failed.\n" , part_num); +return 1 ; + } +} +static int do_mmcops (cmd_tbl_t *cmdtp,int flag,int argc,char *const argv[]) {enum mmc_state state;
@@ -248,6 +273,71 @@ static int do_mmcops(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) curr_device, mmc->part_num);return 0 ; + }else if ((strcmp (argv[1 ],"open" ) ==0 ) || + (strcmp (argv[1 ],"close" ) ==0 )) { +int dev; +struct mmc *mmc; +u32 ack, part_num, access =0 ; + +if (argc ==4 ) { + dev =simple_strtoul (argv[2 ],NULL ,10 ); + part_num =simple_strtoul (argv[3 ],NULL ,10 ); + }else +return CMD_RET_USAGE ; + + mmc =find_mmc_device (dev); +if (!mmc) { +printf ("no mmc device at slot %x\n" , dev); +return 1 ; + } + +if (IS_SD (mmc)) { +printf ("SD device cannot be opened/closed\n" ); +return 1 ; + } + +if ((part_num <=0 ) || (part_num >MMC_NUM_BOOT_PARTITION )) { +printf ("Invalid boot partition number:\n" ); +printf ("Boot partition number cannot be <= 0\n" ); +printf ("EMMC44 supports only 2 boot partitions\n" ); +return 1 ; + } + +if (strcmp (argv[1 ],"open" ) ==0 ) + access = part_num;/* enable R/W access to boot part*/ +if (strcmp (argv[1 ],"close" ) ==0 ) + access =0 ;/* No access to boot partition */ + +/* acknowledge to be sent during boot operation */ + ack =1 ; +return boot_part_access (mmc, ack, part_num, access); + + }else if (strcmp (argv[1 ],"bootpart" ) ==0 ) { +int dev; + dev =simple_strtoul (argv[2 ],NULL ,10 ); + +u32 bootsize =simple_strtoul (argv[3 ],NULL ,10 ); +u32 rpmbsize =simple_strtoul (argv[4 ],NULL ,10 ); +struct mmc *mmc =find_mmc_device (dev); +if (!mmc) { +printf ("no mmc device@slot %x\n" , dev); +return 1 ; + } + +if (IS_SD (mmc)) { +printf ("It is not a EMMC device\n" ); +return 1 ; + } + +if (0 ==mmc_boot_partition_size_change (mmc, + bootsize, rpmbsize)) { +printf ("EMMC boot partition Size %d MB\n" , bootsize); +printf ("EMMC RPMB partition Size %d MB\n" , rpmbsize); +return 0 ; + }else { +printf ("EMMC boot partition Size change Failed.\n" ); +return 1 ; + } } state =MMC_INVALID ;
@@ -317,5 +407,11 @@ U_BOOT_CMD("mmc rescan\n" "mmc part - lists available partition on current mmc device\n" "mmc dev [dev] [part] - show or set current mmc device [partition]\n" - "mmc list - lists available devices"); +"mmc list - lists available devices\n" +"mmc open <dev> <boot_partition>\n" +" - Enable boot_part for booting and enable R/W access of boot_part\n" +"mmc close <dev> <boot_partition>\n" +" - Enable boot_part for booting and disable access to boot_part\n" +"mmc bootpart <device num> <boot part size MB> <RPMB part size MB>\n" + " - change sizes of boot and RPMB partions of specified device\n");#endif
Signature · 1 line
1.8.0
PATCH v7 9/10 COMMON: MMC: Command to support EMMC booting and to resize EMMC boot partition
Dear Amar,
Quoted 4 lines · In message <[email protected]> you…
This patch adds commands to access(open/close) and resize boot partitions on EMMC.
Signed-off-by Amar <[email protected]>Acked-by Simon Glass <[email protected]>
Can you please make this code conditional, so only boards that want this feature (and actually use EMMC) suffer from the increased memory footprint?
Thanks.
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
A dog always bit deepest on the veterinary hand.
- Terry Pratchett, _Wyrd Sisters_PATCH v7 9/10 COMMON: MMC: Command to support EMMC booting and to resize EMMC boot partition
Dear Wolfgang,
Thank you for the comments.
Ok, I will make this code conditional.
I will prepare a new patch and post the same.
Thanks & Regards
Amarendra
Quoted 31 lines · Wolfgang Denk
Dear Amar,
In message <[email protected]>
Quoted 1 line · you
This patch adds commands to access(open/close) and resize boot
partitions on EMMC.
Quoted 3 lines
Signed-off-by Amar <[email protected]>Acked-by Simon Glass <[email protected]>Can you please make this code conditional, so only boards that want this feature (and actually use EMMC) suffer from the increased memory footprint?
Thanks.
Best regards,
Wolfgang Denk
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de A dog always bit deepest on the veterinary hand.
- Terry Pratchett,_WyrdSisters_
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
PATCH v7 10/10 EXYNOS5: I2C: Added FDT and non-FDT support for I2C
In reply to AmarThis patch adds FDT and non-FDT support for I2C, and initialise the I2C channels.
---
Changes since V4:
New patch.
Changes since V5:
1)Removed the function call i2c_init() present inside the function board_i2c_init().
Changes since V6:
No change.
drivers/i2c/s3c24x0_i2c.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-)
drivers/i2c/s3c24x0_i2c.c +10 -2
@@ -524,11 +524,12 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len) len) != 0); } -#ifdef CONFIG_OF_CONTROL void board_i2c_init (const void *blob) { +int i; +#ifdef CONFIG_OF_CONTROL int node_list[CONFIG_MAX_I2C_NUM ]; -int count, i; +int count; count = fdtdec_find_aliases_for_id(blob, "i2c", COMPAT_SAMSUNG_S3C2440_I2C, node_list,
@@ -548,8 +549,15 @@ void board_i2c_init(const void *blob) bus->bus_num = i2c_busses++;exynos_pinmux_config (bus->id,0 ); } +#else +for (i =0 ; i <CONFIG_MAX_I2C_NUM ; i++) { +exynos_pinmux_config ((PERIPH_ID_I2C0 + i), +PINMUX_FLAG_NONE ); + } +#endif } +#ifdef CONFIG_OF_CONTROL static struct s3c24x0_i2c_bus *get_bus (unsigned int bus_idx) {if (bus_idx < i2c_busses)
Signature · 1 line
1.8.0
PATCH v7 10/10 EXYNOS5: I2C: Added FDT and non-FDT support for I2C
Quoted 5 lines · Amar
This patch adds FDT and non-FDT support for I2C, and initialise the I2C channels.
Signed-off-by Amar <[email protected]>
PATCH v7 10/10 EXYNOS5: I2C: Added FDT and non-FDT support for I2C
In reply to AmarDear Amar,
Quoted 12 lines · Amar
This patch adds FDT and non-FDT support for I2C, and initialise the I2C channels.
Signed-off-by Amar <[email protected]>---
Changes since V4:
New patch.Changes since V5:
1)Removed the function calli2c_init()present inside the functionboard_i2c_init().
Quoted 6 lines
Changes since V6:
No change.drivers/i2c/s3c24x0_i2c.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-)
I think, this patch should separate from this patchset.
Why you this add this "i2c" patch to
"EXYNOS5: Enable DWMMC, add FDT support for DWMMC and enable EMMC boot"?
Thanks,
Minkyu Kang.
PATCH v7 10/10 EXYNOS5: I2C: Added FDT and non-FDT support for I2C
Dear Minkyu,
While creating the separate file(exynos5-dt.c) to handle dts, I had to do the changes for i2c also. And those changes became part of this patchset.
Ok, I will separate this from the dwmmc patchset.
Thanks & Regards
Amarendra
Quoted 33 lines · Minkyu Kang
Dear Amar,
Quoted 12 lines · Amar
This patch adds FDT and non-FDT support for I2C, and initialise the I2C channels.
Signed-off-by Amar <[email protected]>---
Changes since V4:
New patch.Changes since V5:
1)Removed the function calli2c_init()present inside the functionboard_i2c_init().Quoted 6 lines
Changes since V6:
No change.drivers/i2c/s3c24x0_i2c.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-)I think, this patch should separate from this patchset.
Why you this add this "i2c" patch to
"EXYNOS5: Enable DWMMC, add FDT support for DWMMC and enable EMMC boot"?Thanks,
Minkyu Kang.
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
PATCH v7 10/10 EXYNOS5: I2C: Added FDT and non-FDT support for I2C
Quoted 5 lines · Amarendra Reddy
Dear Minkyu,
While creating the separate file(exynos5-dt.c) to handle dts, I had to do the changes for i2c also. And those changes became part of this patchset.
Ok, I will separate this from the dwmmc patchset.
OK. thanks.
btw, I've requested to you so many times..
"please don't top posting when replying".
Quoted 33 lines
Thanks & Regards
AmarendraOn 28 March 2013 13:59, Minkyu Kang <mk7.kang at samsung.com <mailto:[email protected]>> wrote:
Dear Amar,
On 05/03/13 22:11, Amar wrote:
> This patch adds FDT and non-FDT support for I2C, and initialise
> the I2C channels.
>
> Signed-off-by: Amar <amarendra.xt at samsung.com <mailto:[email protected]>> > ---
> Changes since V4:
> New patch.
>
> Changes since V5:
> 1)Removed the function calli2c_init()present inside the
> functionboard_i2c_init().
>
> Changes since V6:
> No change.
>
>drivers/i2c/s3c24x0_i2c.c| 12 ++++++++++--
> 1 file changed, 10 insertions(+), 2 deletions(-)
>I think, this patch should separate from this patchset.
Why you this add this "i2c" patch to
"EXYNOS5: Enable DWMMC, add FDT support for DWMMC and enable EMMC boot"?
Quoted 8 lines
Thanks,
Minkyu Kang.
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de <mailto:[email protected]>
http://lists.denx.de/mailman/listinfo/u-boot
Thanks,
Minkyu Kang.