serial: sh-sci: Add OF support
Subsystems (6)
PATCH v6 1/3 serial: sh-sci: Add OF support
We add the capabilty to probe Renesas SCI devices using Device Tree setup.
---
v6:
putting it all together: I posted v5 as an incremental patch - here the full version based on Simon Horman's tree topic/intc-of.
I will post another incremental version as well.
- rename sci at xxxxxxxx to serial at xxxxxxxx
- stick to scbrr-algorithm
.../bindings/tty/serial/renesas,sci-serial.txt | 47 +++++++ drivers/tty/serial/sh-sci.c | 146 +++++++++++++++++++- include/linux/serial_sci.h | 4 + 3 files changed, 193 insertions(+), 4 deletions(-) create mode 100644 Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +47 -0
@@ -0,0 +1,47 @@ +* Renesas SH-Mobile Serial Communication Interface + +Required properties: +- compatible : Should be "renesas,sci-<port type>-uart", where <port type> is + "sci", "scif", "irda", "scifa", "scifb" + or for legacy devices + "sh2_scif_fifodata", "sh3_scif", "sh4_scif", "sh4_scif_no_scsptr", + "sh4_scif_fifodata", "sh7705_scif". +- reg : Address and length of the register set for the device +- interrupts : Should contain the following IRQs in this order: + ERI: receive-error interrupt + RXI: receive-FIFO-data-full interrupt + TXI: transmit-FIFO-data-empty interrupt + BRI: break reception interrupt +- interrupt-names: The IRQ names "eri", "rxi", "txi" and "bri". +- cell-index : The device id. +- renesas,scscr : Should contain a bitfield used by the Serial Control Register. + b7 = SCSCR_TIE + b6 = SCSCR_RIE + b5 = SCSCR_TE + b4 = SCSCR_RE + b3 = SCSCR_REIE + b2 = SCSCR_TOIE + b1 = SCSCR_CKE1 + b0 = SCSCR_CKE0 +- renesas,scbrr-algorithm : Choose an algorithm ID for the baud rate generator. + 1 = SCBRR_ALGO_1 ((clk + 16 * bps) / (16 * bps) - 1) + 2 = SCBRR_ALGO_2 ((clk + 16 * bps) / (32 * bps) - 1) + 3 = SCBRR_ALGO_3 (((clk * 2) + 16 * bps) / (16 * bps) - 1) + 4 = SCBRR_ALGO_4 (((clk * 2) + 16 * bps) / (32 * bps) - 1) + 5 = SCBRR_ALGO_5 (((clk * 1000 / 32) / bps) - 1) + +Optional properties: +- renesas,autoconf : Set if device is capable of auto configuration. + +Example: + serial at e6c50000 { + compatible = "renesas,sci-scifa-uart"; + interrupt-parent = <&intca>; + reg = <0xe6c50000 0x100>; + interrupts = <0x0c20>, <0x0c20>, <0x0c20>, <0x0c20>; + interrupt-names = "eri", "rxi", "txi", "bri"; + cell-index = <1>; + renesas,scscr = <0x30>; + renesas,scbrr-algorithm = <4>; + renesas,autoconf; + };
drivers/tty/serial/sh-sci.c +142 -4
178 lines not on this page · raw message
include/linux/serial_sci.h +4 -0
@@ -11,11 +11,15 @@#define SCIx_NOT_SUPPORTED (-1)enum { +SCBRR_ALGO_INVALID , +SCBRR_ALGO_1 ,/* ((clk + 16 * bps) / (16 * bps) - 1) */ SCBRR_ALGO_2 ,/* ((clk + 16 * bps) / (32 * bps) - 1) */ SCBRR_ALGO_3 ,/* (((clk * 2) + 16 * bps) / (16 * bps) - 1) */ SCBRR_ALGO_4 ,/* (((clk * 2) + 16 * bps) / (32 * bps) - 1) */ SCBRR_ALGO_5 ,/* (((clk * 1000 / 32) / bps) - 1) */ + +SCBRR_NR_ALGOS , };#define SCSCR_TIE (1 << 7)
Signature · 1 line
1.7.9.5
PATCH v6 2/3 ARM: mach-shmobile: r8a7740: Add DT names to clock list
This adds temporarily the alternative device names to the clock list that are used when booting via Device Tree setup.
--- arch/arm/mach-shmobile/clock-r8a7740.c | 9 +++++++++ 1 file changed, 9 insertions(+)
arch/arm/mach-shmobile/clock-r8a7740.c +9 -0
@@ -593,18 +593,27 @@ static struct clk_lookup lookups[] = {CLKDEV_DEV_ID ("sh_mobile_ceu.1" , &mstp_clks[MSTP128 ]),CLKDEV_DEV_ID ("sh-sci.4" , &mstp_clks[MSTP200 ]), +CLKDEV_DEV_ID ("e6c80000.serial" , &mstp_clks[MSTP200 ]),CLKDEV_DEV_ID ("sh-sci.3" , &mstp_clks[MSTP201 ]), +CLKDEV_DEV_ID ("e6c70000.serial" , &mstp_clks[MSTP201 ]),CLKDEV_DEV_ID ("sh-sci.2" , &mstp_clks[MSTP202 ]), +CLKDEV_DEV_ID ("e6c60000.serial" , &mstp_clks[MSTP202 ]),CLKDEV_DEV_ID ("sh-sci.1" , &mstp_clks[MSTP203 ]), +CLKDEV_DEV_ID ("e6c50000.serial" , &mstp_clks[MSTP203 ]),CLKDEV_DEV_ID ("sh-sci.0" , &mstp_clks[MSTP204 ]), +CLKDEV_DEV_ID ("e6c40000.serial" , &mstp_clks[MSTP204 ]),CLKDEV_DEV_ID ("sh-sci.8" , &mstp_clks[MSTP206 ]), +CLKDEV_DEV_ID ("e6c30000.serial" , &mstp_clks[MSTP206 ]),CLKDEV_DEV_ID ("sh-sci.5" , &mstp_clks[MSTP207 ]), +CLKDEV_DEV_ID ("e6cb0000.serial" , &mstp_clks[MSTP207 ]),CLKDEV_DEV_ID ("sh-dma-engine.3" , &mstp_clks[MSTP214 ]),CLKDEV_DEV_ID ("sh-dma-engine.2" , &mstp_clks[MSTP216 ]),CLKDEV_DEV_ID ("sh-dma-engine.1" , &mstp_clks[MSTP217 ]),CLKDEV_DEV_ID ("sh-dma-engine.0" , &mstp_clks[MSTP218 ]),CLKDEV_DEV_ID ("sh-sci.7" , &mstp_clks[MSTP222 ]), +CLKDEV_DEV_ID ("e6cd0000.serial" , &mstp_clks[MSTP222 ]),CLKDEV_DEV_ID ("sh-sci.6" , &mstp_clks[MSTP230 ]), +CLKDEV_DEV_ID ("e6cc0000.serial" , &mstp_clks[MSTP230 ]),CLKDEV_DEV_ID ("sh_cmt.10" , &mstp_clks[MSTP329 ]), CLKDEV_DEV_ID("sh_fsi2", &mstp_clks[MSTP328]),
Signature · 1 line
1.7.9.5
PATCH v6 3/3 ARM: mach-shmobile: r8a7740: Setup the serial devices using DT
In reply to Bastian HechtWe can now use the Device Tree for bringing up our serial devices on the SoC r8a7740.
We remove the power domain association. We will move the info into the DT setup as soon as we have support for it. For now this is fine as we use the power domain governor "pm_domain_always_on_gov" for A3SP.
--- arch/arm/boot/dts/r8a7740.dtsi | 108 +++++++++++++++++++ arch/arm/mach-shmobile/setup-r8a7740.c | 180 -------------------------------- 2 files changed, 108 insertions(+), 180 deletions(-)
arch/arm/boot/dts/r8a7740.dtsi +108 -0
@@ -767,4 +767,112 @@ gpio-controller; #gpio-cells = <2>; }; + + serial at e6c40000 { + compatible = "renesas,sci-scifa-uart"; + interrupt-parent = <&intca>; + reg = <0xe6c40000 0x100>; + interrupts = <0x0c00>, <0x0c00>, <0x0c00>, <0x0c00>; + interrupt-names = "eri", "rxi", "txi", "bri"; + cell-index = <0>; + renesas,scscr = <0x30>; + renesas,scbrr-algorithm = <4>; + renesas,autoconf; + }; + + serial at e6c50000 { + compatible = "renesas,sci-scifa-uart"; + interrupt-parent = <&intca>; + reg = <0xe6c50000 0x100>; + interrupts = <0x0c20>, <0x0c20>, <0x0c20>, <0x0c20>; + interrupt-names = "eri", "rxi", "txi", "bri"; + cell-index = <1>; + renesas,scscr = <0x30>; + renesas,scbrr-algorithm = <4>; + renesas,autoconf; + }; + + serial at e6c60000 { + compatible = "renesas,sci-scifa-uart"; + interrupt-parent = <&intca>; + reg = <0xe6c60000 0x100>; + interrupts = <0x0c40>, <0x0c40>, <0x0c40>, <0x0c40>; + interrupt-names = "eri", "rxi", "txi", "bri"; + cell-index = <2>; + renesas,scscr = <0x30>; + renesas,scbrr-algorithm = <4>; + renesas,autoconf; + }; + + serial at e6c70000 { + compatible = "renesas,sci-scifa-uart"; + interrupt-parent = <&intca>; + reg = <0xe6c70000 0x100>; + interrupts = <0x0c60>, <0x0c60>, <0x0c60>, <0x0c60>; + interrupt-names = "eri", "rxi", "txi", "bri"; + cell-index = <3>; + renesas,scscr = <0x30>; + renesas,scbrr-algorithm = <4>; + renesas,autoconf; + }; + + serial at e6c80000 { + compatible = "renesas,sci-scifa-uart"; + interrupt-parent = <&intca>; + reg = <0xe6c80000 0x100>; + interrupts = <0x0d20>, <0x0d20>, <0x0d20>, <0x0d20>; + interrupt-names = "eri", "rxi", "txi", "bri"; + cell-index = <4>; + renesas,scscr = <0x30>; + renesas,scbrr-algorithm = <4>; + renesas,autoconf; + }; + + serial at e6cb0000 { + compatible = "renesas,sci-scifa-uart"; + interrupt-parent = <&intca>; + reg = <0xe6cb0000 0x100>; + interrupts = <0x0d40>, <0x0d40>, <0x0d40>, <0x0d40>; + interrupt-names = "eri", "rxi", "txi", "bri"; + cell-index = <5>; + renesas,scscr = <0x30>; + renesas,scbrr-algorithm = <4>; + renesas,autoconf; + }; + + serial at e6cc0000 { + compatible = "renesas,sci-scifa-uart"; + interrupt-parent = <&intca>; + reg = <0xe6cc0000 0x100>; + interrupts = <0x04c0>, <0x04c0>, <0x04c0>, <0x04c0>; + interrupt-names = "eri", "rxi", "txi", "bri"; + cell-index = <6>; + renesas,scscr = <0x30>; + renesas,scbrr-algorithm = <4>; + renesas,autoconf; + }; + + serial at 0xe6cd0000 { + compatible = "renesas,sci-scifa-uart"; + interrupt-parent = <&intca>; + reg = <0xe6cd0000 0x100>; + interrupts = <0x04e0>, <0x04e0>, <0x04e0>, <0x04e0>; + interrupt-names = "eri", "rxi", "txi", "bri"; + cell-index = <7>; + renesas,scscr = <0x30>; + renesas,scbrr-algorithm = <4>; + renesas,autoconf; + }; + + serial at e6c30000 { + compatible = "renesas,sci-scifb-uart"; + interrupt-parent = <&intca>; + reg = <0xe6c30000 0x100>; + interrupts = <0x0d60>, <0x0d60>, <0x0d60>, <0x0d60>; + interrupt-names = "eri", "rxi", "txi", "bri"; + cell-index = <8>; + renesas,scscr = <0x30>; + renesas,scbrr-algorithm = <4>; + renesas,autoconf; + }; };
arch/arm/mach-shmobile/setup-r8a7740.c +0 -180
198 lines not on this page · raw message
Signature · 1 line
1.7.9.5
PATCH v6 1/3 serial: sh-sci: Add OF support
In reply to Bastian HechtHi Bastian,
Thanks for the patch.
Quoted 49 lines · On Wednesday 06 March 2013 12:30:35 Bastian Hecht wrote:
We add the capabilty to probe Renesas SCI devices using Device Tree setup.
Signed-off-by Bastian Hecht <[email protected]>Reviewed-by Paul Mundt <[email protected]>Acked-by Arnd Bergmann <[email protected]>---
v6:
putting it all together: I posted v5 as an incremental patch - here the full version based on Simon Horman's tree topic/intc-of.I will post another incremental version as well.
- rename sci at xxxxxxxx to serial at xxxxxxxx
- stick to scbrr-algorithm.../bindings/tty/serial/renesas,sci-serial.txt | 47 +++++++ drivers/tty/serial/sh-sci.c | 146 +++++++++++++++++++- include/linux/serial_sci.h | 4 + 3 files changed, 193 insertions(+), 4 deletions(-) create mode 100644
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txtdiff --git
a/Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txtb/Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txtnew file mode 100644
index 0000000..d80039eDocumentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +4
-0@@ -0,0 +1,47 @@ +* Renesas SH-Mobile Serial Communication Interface + +Required properties: +- compatible : Should be "renesas,sci-<port type>-uart", where <port type>is + "sci", "scif", "irda", "scifa", "scifb"
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +12
-0+ or for legacy devices + "sh2_scif_fifodata", "sh3_scif", "sh4_scif", "sh4_scif_no_scsptr", + "sh4_scif_fifodata", "sh7705_scif". +- reg : Address and length of the register set for the device +- interrupts : Should contain the following IRQs in this order: + ERI: receive-error interrupt + RXI: receive-FIFO-data-full interrupt + TXI: transmit-FIFO-data-empty interrupt + BRI: break reception interrupt +- interrupt-names: The IRQ names "eri", "rxi", "txi" and "bri". +- cell-index : The device id. +- renesas,scscr : Should contain a bitfield used by the Serial ControlRegister.
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt line 25
Quoted 8 lines
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +8
-0+ b7 = SCSCR_TIE + b6 = SCSCR_RIE + b5 = SCSCR_TE + b4 = SCSCR_RE + b3 = SCSCR_REIE + b2 = SCSCR_TOIE + b1 = SCSCR_CKE1 + b0 = SCSCR_CKE0
What is that for exactly ?
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt line 31
Quoted 7 lines
+- renesas,scbrr-algorithm : Choose an algorithm ID for the baud rate generator.
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +5
-0+ 1 = SCBRR_ALGO_1 ((clk + 16 * bps) / (16 * bps) - 1) + 2 = SCBRR_ALGO_2 ((clk + 16 * bps) / (32 * bps) - 1) + 3 = SCBRR_ALGO_3 (((clk * 2) + 16 * bps) / (16 * bps) - 1) + 4 = SCBRR_ALGO_4 (((clk * 2) + 16 * bps) / (32 * bps) - 1) + 5 = SCBRR_ALGO_5 (((clk * 1000 / 32) / bps) - 1)
Isn't it a property specific to our implementation of the driver instead of a hardware property ? How is one supposed to select the right algorithm ?
Quoted 223 lines
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +15
-0+Optional properties: +- renesas,autoconf : Set if device is capable of auto configuration. + +Example: + serial at e6c50000 { + compatible = "renesas,sci-scifa-uart"; + interrupt-parent = <&intca>; + reg = <0xe6c50000 0x100>; + interrupts = <0x0c20>, <0x0c20>, <0x0c20>, <0x0c20>; + interrupt-names = "eri", "rxi", "txi", "bri"; + cell-index = <1>; + renesas,scscr = <0x30>; + renesas,scbrr-algorithm = <4>; + renesas,autoconf; + };drivers/tty/serial/sh-sci.c +129
-3@@ -52,6 +52,7 @@#include <linux/scatterlist.h> #include <linux/slab.h> #include <linux/gpio.h> +#include <linux/of.h> #ifdef CONFIG_SUPERH #include <asm/sh_bios.h> @@ -2353,6 +2354,131 @@ static int sci_remove(struct platform_device *dev)return 0 ; } +static const struct of_device_id of_sci_match[] = { + { .compatible ="renesas,sci-sci-uart" , + .data = (void *)SCIx_SCI_REGTYPE }, + { .compatible ="renesas,sci-scif-uart" , + .data = (void *)SCIx_SH4_SCIF_REGTYPE, }, + { .compatible ="renesas,sci-irda-uart" , + .data = (void *)SCIx_IRDA_REGTYPE }, + { .compatible ="renesas,sci-scifa-uart" , + .data = (void *)SCIx_SCIFA_REGTYPE }, + { .compatible ="renesas,sci-scifb-uart" , + .data = (void *)SCIx_SCIFB_REGTYPE }, + { .compatible ="renesas,sci-sh2_scif_fifodata-uart" , + .data = (void *)SCIx_SH2_SCIF_FIFODATA_REGTYPE }, + { .compatible ="renesas,sci-sh3_scif-uart" , + .data = (void *)SCIx_SH3_SCIF_REGTYPE }, + { .compatible ="renesas,sci-sh4_scif-uart" , + .data = (void *)SCIx_SH4_SCIF_REGTYPE }, + { .compatible ="renesas,sci-sh4_scif_no_scsptr-uart" , + .data = (void *)SCIx_SH4_SCIF_NO_SCSPTR_REGTYPE }, + { .compatible ="renesas,sci-sh4_scif_fifodata-uart" , + .data = (void *)SCIx_SH4_SCIF_FIFODATA_REGTYPE }, + { .compatible ="renesas,sci-sh7705_scif-uart" , + .data = (void *)SCIx_SH7705_SCIF_REGTYPE }, + {}, +}; +MODULE_DEVICE_TABLE (of, of_sci_match); + +static struct plat_sci_port *sci_parse_dt (struct platform_device *pdev, +int *dev_id) +{ +struct plat_sci_port *p; +struct device_node *np = pdev->dev.of_node; +const struct of_device_id *match; +struct resource *res; +const __be32 *prop; +int i, irq, val; + +if (!IS_ENABLED (CONFIG_OF ) || !np) +return NULL ; + + match =of_match_node (of_sci_match, pdev->dev.of_node); +if (!match || !match->data) { +dev_err (&pdev->dev,"OF match error\n" ); +return NULL ; + } + + p =devm_kzalloc (&pdev->dev,sizeof (struct plat_sci_port ),GFP_KERNEL ); +if (!p) { +dev_err (&pdev->dev,"failed to allocate DT config data\n" ); +return NULL ; + } + + res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); +if (!res) { +dev_err (&pdev->dev,"failed to get I/O memory\n" ); +return NULL ; + } + p->mapbase = res->start; + +for (i =0 ; i < SCIx_NR_IRQS; i++) { + irq =platform_get_irq (pdev, i); +if (irq <0 ) { +dev_err (&pdev->dev,"failed to get irq data %d\n" , i); +return NULL ; + } + p->irqs[i] = irq; + } + + prop =of_get_property (np,"cell-index" ,NULL ); +if (!prop) { +dev_err (&pdev->dev,"required DT prop cell-index missing\n" ); +return NULL ; + } + *dev_id =be32_to_cpup (prop); + + prop =of_get_property (np,"renesas,scscr" ,NULL ); +if (!prop) { +dev_err (&pdev->dev,"required DT prop scscr missing\n" ); +return NULL ; + } + p->scscr =be32_to_cpup (prop); + + prop =of_get_property (np,"renesas,scbrr-algorithm" ,NULL ); +if (!prop) { +dev_err (&pdev->dev,"required DT prop scbrr-algorithm missing\n" ); +return NULL ; + } + val =be32_to_cpup (prop); +if (val <=SCBRR_ALGO_INVALID || val >=SCBRR_NR_ALGOS ) { +dev_err (&pdev->dev,"DT prop clock-algorithm out of range\n" ); +return NULL ; + } + p->scbrr_algo_id = val; + + p->flags =UPF_IOREMAP ; +if (of_get_property (np,"renesas,autoconf" ,NULL )) + p->flags |=UPF_BOOT_AUTOCONF ; + + p->regtype = (unsigned int )match->data; + +switch (p->regtype) { +case SCIx_SCI_REGTYPE: + p->type =PORT_SCI ; +break ; +case SCIx_SH4_SCIF_REGTYPE: + p->type =PORT_SCIF ; +break ; +case SCIx_IRDA_REGTYPE: + p->type =PORT_IRDA ; +break ; +case SCIx_SCIFA_REGTYPE: + p->type =PORT_SCIFA ; +break ; +case SCIx_SCIFB_REGTYPE: + p->type =PORT_SCIFB ; +break ; +default : +/* legacy register sets default to PORT_SCIF */ + p->type =PORT_SCIF ; +break ; + } + +return p; +} + static int sci_probe_single(struct platform_device *dev, unsigned int index, struct plat_sci_port *p,@@ -2385,9 +2511,9 @@ static int sci_probe_single(struct platform_device *dev, static int sci_probe(struct platform_device *dev) { -struct plat_sci_port *p = dev->dev.platform_data; -struct sci_port *sp = &sci_ports[dev->id]; -int ret; +struct plat_sci_port *p; +struct sci_port *sp; +int ret, dev_id = dev->id;/* drivers/tty/serial/sh-sci.c +13
-1* If we've come here via earlyprintk initialization, head off to @@ -2397,9 +2523,20 @@ static int sci_probe(struct platform_device *dev)if (is_early_platform_device (dev))return sci_probe_earlyprintk (dev); +if (dev->dev.of_node) + p =sci_parse_dt (dev, &dev_id); +else + p = dev->dev.platform_data; + +if (!p) { +dev_err (&dev->dev,"no setup data supplied\n" ); +return -EINVAL ; + } + + sp = &sci_ports[dev_id];platform_set_drvdata (dev, sp); - ret =sci_probe_single (dev, dev->id, p, sp); + ret =sci_probe_single (dev, dev_id, p, sp);if (ret)return ret;@@ -2451,6 +2588,7 @@ static struct platform_driver sci_driver = { .name = "sh-sci", .owner = THIS_MODULE, .pm = &sci_dev_pm_ops, + .of_match_table = of_match_ptr(of_sci_match), }, };include/linux/serial_sci.h +4
-0@@ -11,11 +11,15 @@#define SCIx_NOT_SUPPORTED (-1)enum { +SCBRR_ALGO_INVALID , +SCBRR_ALGO_1 ,/* ((clk + 16 * bps) / (16 * bps) - 1) */ SCBRR_ALGO_2 ,/* ((clk + 16 * bps) / (32 * bps) - 1) */ SCBRR_ALGO_3 ,/* (((clk * 2) + 16 * bps) / (16 * bps) - 1) */ SCBRR_ALGO_4 ,/* (((clk * 2) + 16 * bps) / (32 * bps) - 1) */ SCBRR_ALGO_5 ,/* (((clk * 1000 / 32) / bps) - 1) */ + +SCBRR_NR_ALGOS , };#define SCSCR_TIE (1 << 7)
Signature · 3 lines
Regards, Laurent Pinchart
PATCH v6 1/3 serial: sh-sci: Add OF support
Quoted 70 lines · On Wednesday 06 March 2013 13:10:55 Laurent Pinchart wrote:
Quoted 50 lines · On Wednesday 06 March 2013 12:30:35 Bastian Hecht wrote:
We add the capabilty to probe Renesas SCI devices using Device Tree setup.
Signed-off-by Bastian Hecht <[email protected]>Reviewed-by Paul Mundt <[email protected]>Acked-by Arnd Bergmann <[email protected]>---
v6:
putting it all together: I posted v5 as an incremental patch - here the full version based on Simon Horman's tree topic/intc-of.I will post another incremental version as well.
- rename sci at xxxxxxxx to serial at xxxxxxxx
- stick to scbrr-algorithm.../bindings/tty/serial/renesas,sci-serial.txt | 47 +++++++ drivers/tty/serial/sh-sci.c | 146 ++++++++++++++- include/linux/serial_sci.h | 4 + 3 files changed, 193 insertions(+), 4 deletions(-) create mode 100644
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txtdiff --git
a/Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txtb/Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txtnew file mode 100644
index 0000000..d80039eDocumentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +4
-0@@ -0,0 +1,47 @@ +* Renesas SH-Mobile Serial Communication Interface + +Required properties: +- compatible : Should be "renesas,sci-<port type>-uart", where <porttype>
is + "sci", "scif", "irda", "scifa", "scifb"Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +12
-0+ or for legacy devices + "sh2_scif_fifodata", "sh3_scif", "sh4_scif", "sh4_scif_no_scsptr", + "sh4_scif_fifodata", "sh7705_scif". +- reg : Address and length of the register set for the device +- interrupts : Should contain the following IRQs in this order: + ERI: receive-error interrupt + RXI: receive-FIFO-data-full interrupt + TXI: transmit-FIFO-data-empty interrupt + BRI: break reception interrupt +- interrupt-names: The IRQ names "eri", "rxi", "txi" and "bri". +- cell-index : The device id. +- renesas,scscr : Should contain a bitfield used by the Serial ControlRegister.
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt line 25
Quoted 8 lines
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +8
-0+ b7 = SCSCR_TIE + b6 = SCSCR_RIE + b5 = SCSCR_TE + b4 = SCSCR_RE + b3 = SCSCR_REIE + b2 = SCSCR_TOIE + b1 = SCSCR_CKE1 + b0 = SCSCR_CKE0What is that for exactly ?
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt line 31
Quoted 7 lines
+- renesas,scbrr-algorithm : Choose an algorithm ID for the baud rate generator.
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +5
-0+ 1 = SCBRR_ALGO_1 ((clk + 16 * bps) / (16 * bps) - 1) + 2 = SCBRR_ALGO_2 ((clk + 16 * bps) / (32 * bps) - 1) + 3 = SCBRR_ALGO_3 (((clk * 2) + 16 * bps) / (16 * bps) - 1) + 4 = SCBRR_ALGO_4 (((clk * 2) + 16 * bps) / (32 * bps) - 1) + 5 = SCBRR_ALGO_5 (((clk * 1000 / 32) / bps) - 1)
Quoted 2 lines
Isn't it a property specific to our implementation of the driver instead of a hardware property ? How is one supposed to select the right algorithm ?
I realize I haven't expressed myself very clearly here. What I mean is that expressing how the baud rate generator works internally using an algorithm ID is pretty specific to the Linux driver.
I assume that, for a given serial port on a given SoC, the algorithm that matches the baud rate generator hardware implementation needs to be selected. Can't this information be inferred from the compatible string and port number ?
Signature · 3 lines
Regards, Laurent Pinchart
PATCH v6 1/3 serial: sh-sci: Add OF support
Quoted 13 lines · Laurent Pinchart
Quoted 11 lines · On Wednesday 06 March 2013 13:10:55 Laurent Pinchart wrote:
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt line 31
Quoted 7 lines · On Wednesday 06 March 2013 12:30:35 Bastian Hecht wrote:
+- renesas,scbrr-algorithm : Choose an algorithm ID for the baud rate generator.
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +5
-0+ 1 = SCBRR_ALGO_1 ((clk + 16 * bps) / (16 * bps) - 1) + 2 = SCBRR_ALGO_2 ((clk + 16 * bps) / (32 * bps) - 1) + 3 = SCBRR_ALGO_3 (((clk * 2) + 16 * bps) / (16 * bps) - 1) + 4 = SCBRR_ALGO_4 (((clk * 2) + 16 * bps) / (32 * bps) - 1) + 5 = SCBRR_ALGO_5 (((clk * 1000 / 32) / bps) - 1)Isn't it a property specific to our implementation of the driver instead of a hardware property ? How is one supposed to select the right algorithm ?
Quoted 9 lines
I realize I haven't expressed myself very clearly here. What I mean is that expressing how the baud rate generator works internally using an algorithm ID is pretty specific to the Linux driver.
I assume that, for a given serial port on a given SoC, the algorithm that matches the baud rate generator hardware implementation needs to be selected. Can't this information be inferred from the compatible string and port number ?
Now that we have split things out in to regtype for the compat string we may be able to get away with selecting defaults that match the regtype and drop it from the binding (assuming all future parts remain relatively sane), but it would still complicate things if we were to ever do DT support for legacy CPUs. It's not enough to tie to the port type, as there are plenty of cases where the port type uses a non-standard algo on some CPU subtypes (although things are pretty consistent for the arm side so far).
PATCH v6 1/3 serial: sh-sci: Add OF support
Hi Paul,
2013/3/6 Paul Mundt <[email protected]>:
Quoted 23 lines · Laurent Pinchart
Quoted 13 lines · On Wednesday 06 March 2013 13:10:55 Laurent Pinchart wrote:
Quoted 11 lines · On Wednesday 06 March 2013 12:30:35 Bastian Hecht wrote:
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt line 31
Quoted 7 lines
+- renesas,scbrr-algorithm : Choose an algorithm ID for the baud rate generator.
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +5
-0+ 1 = SCBRR_ALGO_1 ((clk + 16 * bps) / (16 * bps) - 1) + 2 = SCBRR_ALGO_2 ((clk + 16 * bps) / (32 * bps) - 1) + 3 = SCBRR_ALGO_3 (((clk * 2) + 16 * bps) / (16 * bps) - 1) + 4 = SCBRR_ALGO_4 (((clk * 2) + 16 * bps) / (32 * bps) - 1) + 5 = SCBRR_ALGO_5 (((clk * 1000 / 32) / bps) - 1)Isn't it a property specific to our implementation of the driver instead of a hardware property ? How is one supposed to select the right algorithm ?
Quoted 9 lines
I realize I haven't expressed myself very clearly here. What I mean is that expressing how the baud rate generator works internally using an algorithm ID is pretty specific to the Linux driver.
I assume that, for a given serial port on a given SoC, the algorithm that matches the baud rate generator hardware implementation needs to be selected. Can't this information be inferred from the compatible string and port number ?
Quoted 8 lines
Now that we have split things out in to regtype for the compat string we may be able to get away with selecting defaults that match the regtype and drop it from the binding (assuming all future parts remain relatively sane), but it would still complicate things if we were to ever do DT support for legacy CPUs. It's not enough to tie to the port type, as there are plenty of cases where the port type uses a non-standard algo on some CPU subtypes (although things are pretty consistent for the arm side so far).
regarding Laurent's question about the SCSCR register, do you think we can assume the same there?
If so we could start out omitting these 2 properties and rely on adding optional properties later in case we want to support legacy stuff.
I don't see where it complicates things as we probably got the minimal binding set then.
Thanks,
Bastian
PATCH v6 1/3 serial: sh-sci: Add OF support
In reply to Paul MundtQuoted 8 lines · Paul Mundt
Now that we have split things out in to regtype for the compat string we may be able to get away with selecting defaults that match the regtype and drop it from the binding (assuming all future parts remain relatively sane), but it would still complicate things if we were to ever do DT support for legacy CPUs. It's not enough to tie to the port type, as there are plenty of cases where the port type uses a non-standard algo on some CPU subtypes (although things are pretty consistent for the arm side so far).
Maybe we could document it as an optional property that we may use for the legacy CPUs if necessary, but put it into the ARM dts files or into the driver implementation for the time being.
Arnd
PATCH v6 1/3 serial: sh-sci: Add OF support
In reply to Laurent PinchartHi Laurent,
Quoted 11 lines
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt line 25
Quoted 10 lines
+- renesas,scscr : Should contain a bitfield used by the Serial Control Register.
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +8
-0+ b7 = SCSCR_TIE + b6 = SCSCR_RIE + b5 = SCSCR_TE + b4 = SCSCR_RE + b3 = SCSCR_REIE + b2 = SCSCR_TOIE + b1 = SCSCR_CKE1 + b0 = SCSCR_CKE0
Quoted 1 line
What is that for exactly ?
What I can see from 3 different datasheets (sh7372, sh73a0, r8a7740) the first 2 bits differ in meaning.
On r8a7740 it depends: In asynchronous mode the first 2 bits CKE0/1 define whether you want to use an external clock to drive the baud generator or if you want to use the internal SUB clock. If you use the SUB clock you can further define if you want to use a subscaled SUB clock in the SCSMR register. In synchronous mode you must rely on the internal clock for the baud generator and can select if the SCK pin is used as clock input or output.
On sh73a0 and sh7372 it's used to control the output clock SCK (set it to high impedance or actually output a clock when in sychronous mode)
Bit 2 and 3 don't exist in my datasheets.
The other bits define under which conditions you receive interrupts (send FIFO empty, receive FIFO full) and which bits you need to start transfers (one bit to start sending, one receiving). The bits 8 to 31 are used to set up DMA transfers and various interrupt events like error status and finish transfers. I haven't included them as they are not used in the driver.
Thanks,
Bastian
PATCH v6 1/3 serial: sh-sci: Add OF support
Hi Bastian,
Quoted 18 lines · On Thursday 07 March 2013 11:26:29 Bastian Hecht wrote:
Hi Laurent,
Quoted 11 lines
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt line 25
Quoted 10 lines
+- renesas,scscr : Should contain a bitfield used by the Serial Control Register.
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +8
-0+ b7 = SCSCR_TIE + b6 = SCSCR_RIE + b5 = SCSCR_TE + b4 = SCSCR_RE + b3 = SCSCR_REIE + b2 = SCSCR_TOIE + b1 = SCSCR_CKE1 + b0 = SCSCR_CKE0Quoted 1 line
What is that for exactly ?
What I can see from 3 different datasheets (sh7372, sh73a0, r8a7740) the first 2 bits differ in meaning.
Quoted 7 lines
On r8a7740 it depends: In asynchronous mode the first 2 bits CKE0/1 define whether you want to use an external clock to drive the baud generator or if you want to use the internal SUB clock. If you use the SUB clock you can further define if you want to use a subscaled SUB clock in the SCSMR register. In synchronous mode you must rely on the internal clock for the baud generator and can select if the SCK pin is used as clock input or output.
What about adding an optional source clock property to the bindings, that would contain the phandle of the source clock ? If the property is absent then the internal clock would be used.
How is subscaling used in practice ?
Quoted 2 lines
On sh73a0 and sh7372 it's used to control the output clock SCK (set it to high impedance or actually output a clock when in sychronous mode)
Maybe we could add a synchronous mode property to the DT bindings and use it to infer the bit values.
Quoted 8 lines
Bit 2 and 3 don't exist in my datasheets.
The other bits define under which conditions you receive interrupts (send FIFO empty, receive FIFO full) and which bits you need to start transfers (one bit to start sending, one receiving). The bits 8 to 31 are used to set up DMA transfers and various interrupt events like error status and finish transfers. I haven't included them as they are not used in the driver.
If they're not used maybe we can drop them :-)
Signature · 3 lines
Regards, Laurent Pinchart
PATCH v6 1/3 serial: sh-sci: Add OF support
Quoted 25 lines · Laurent Pinchart
Quoted 16 lines · On Thursday 07 March 2013 11:26:29 Bastian Hecht wrote:
Quoted 11 lines
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt line 25
Quoted 10 lines
+- renesas,scscr : Should contain a bitfield used by the Serial Control Register.
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +8
-0+ b7 = SCSCR_TIE + b6 = SCSCR_RIE + b5 = SCSCR_TE + b4 = SCSCR_RE + b3 = SCSCR_REIE + b2 = SCSCR_TOIE + b1 = SCSCR_CKE1 + b0 = SCSCR_CKE0Quoted 1 line
What is that for exactly ?
What I can see from 3 different datasheets (sh7372, sh73a0, r8a7740) the first 2 bits differ in meaning.
Quoted 7 lines
On r8a7740 it depends: In asynchronous mode the first 2 bits CKE0/1 define whether you want to use an external clock to drive the baud generator or if you want to use the internal SUB clock. If you use the SUB clock you can further define if you want to use a subscaled SUB clock in the SCSMR register. In synchronous mode you must rely on the internal clock for the baud generator and can select if the SCK pin is used as clock input or output.
Quoted 4 lines
What about adding an optional source clock property to the bindings, that would contain the phandle of the source clock ? If the property is absent then the internal clock would be used.
We can't really use the internal oscillator at the moment, it's one of the things that is blocked on adoption of the common struct clk work. The baud rate generator algo will likewise differ depending on whether it's using an internally generated clock or not, which also makes a different set of baud rates available.
My plan originally was to wait until the common struct clk stuff came along well enough that we could provide a clock dynamically depending on the target baud (or for avoiding cpufreq pre/post-change notifier chains), but this obviously hasn't happened yet.
I think your idea for the abstraction with the phandle sounds like the right approach, but we aren't presently in a state where we can handle that.
Quoted 11 lines
Quoted 8 lines
Bit 2 and 3 don't exist in my datasheets.
The other bits define under which conditions you receive interrupts (send FIFO empty, receive FIFO full) and which bits you need to start transfers (one bit to start sending, one receiving). The bits 8 to 31 are used to set up DMA transfers and various interrupt events like error status and finish transfers. I haven't included them as they are not used in the driver.
If they're not used maybe we can drop them :-)
Obviously they're used, otherwise they wouldn't be defined in the common header. Whether they are used by these specific CPUs or not isn't relevant, as there are plenty of cases where they are. grep harder.
PATCH v6 1/3 serial: sh-sci: Add OF support
Hi Paul,
Quoted 37 lines · On Tuesday 12 March 2013 17:20:39 Paul Mundt wrote:
Quoted 26 lines · Laurent Pinchart
Quoted 17 lines · On Thursday 07 March 2013 11:26:29 Bastian Hecht wrote:
Quoted 12 lines
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt line 25
Quoted 11 lines
+- renesas,scscr : Should contain a bitfield used by the Serial Control
Register.Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +8
-0+ b7 = SCSCR_TIE + b6 = SCSCR_RIE + b5 = SCSCR_TE + b4 = SCSCR_RE + b3 = SCSCR_REIE + b2 = SCSCR_TOIE + b1 = SCSCR_CKE1 + b0 = SCSCR_CKE0Quoted 1 line
What is that for exactly ?
What I can see from 3 different datasheets (sh7372, sh73a0, r8a7740) the first 2 bits differ in meaning.
Quoted 7 lines
On r8a7740 it depends: In asynchronous mode the first 2 bits CKE0/1 define whether you want to use an external clock to drive the baud generator or if you want to use the internal SUB clock. If you use the SUB clock you can further define if you want to use a subscaled SUB clock in the SCSMR register. In synchronous mode you must rely on the internal clock for the baud generator and can select if the SCK pin is used as clock input or output.
Quoted 3 lines
What about adding an optional source clock property to the bindings, that would contain the phandle of the source clock ? If the property is absent then the internal clock would be used.
We can't really use the internal oscillator at the moment, it's one of the things that is blocked on adoption of the common struct clk work. The baud rate generator algo will likewise differ depending on whether it's using an internally generated clock or not, which also makes a different set of baud rates available.
Quoted 8 lines
My plan originally was to wait until the common struct clk stuff came along well enough that we could provide a clock dynamically depending on the target baud (or for avoiding cpufreq pre/post-change notifier chains), but this obviously hasn't happened yet.
I think your idea for the abstraction with the phandle sounds like the right approach, but we aren't presently in a state where we can handle that.
Do the platforms that will be converted to DT currently need to make the clock source configurable ? If not we could just leave it out of the DT bindings until needed. Hopefully by then we'll have a common clock framework implementation.
Quoted 9 lines
Quoted 9 lines
Quoted 8 lines
Bit 2 and 3 don't exist in my datasheets.
The other bits define under which conditions you receive interrupts (send FIFO empty, receive FIFO full) and which bits you need to start transfers (one bit to start sending, one receiving). The bits 8 to 31 are used to set up DMA transfers and various interrupt events like error status and finish transfers. I haven't included them as they are not used in the driver.
Quoted 5 lines
Quoted 1 line
If they're not used maybe we can drop them :-)
Obviously they're used, otherwise they wouldn't be defined in the common header. Whether they are used by these specific CPUs or not isn't relevant, as there are plenty of cases where they are. grep harder.
My point is that if they're only used by arm/sh/* SoCs we don't need to support them in DT.
Signature · 3 lines
Regards, Laurent Pinchart
PATCH v6 1/3 serial: sh-sci: Add OF support
Hi,
2013/3/12 Laurent Pinchart <[email protected]>:
Quoted 45 lines
Hi Paul,
Quoted 42 lines · On Tuesday 12 March 2013 17:20:39 Paul Mundt wrote:
Quoted 26 lines · Laurent Pinchart
Quoted 17 lines · On Thursday 07 March 2013 11:26:29 Bastian Hecht wrote:
Quoted 12 lines
Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt line 25
Quoted 11 lines
+- renesas,scscr : Should contain a bitfield used by the Serial Control
Register.Documentation/devicetree/bindings/tty/serial/renesas,sci-serial.txt new file +8
-0+ b7 = SCSCR_TIE + b6 = SCSCR_RIE + b5 = SCSCR_TE + b4 = SCSCR_RE + b3 = SCSCR_REIE + b2 = SCSCR_TOIE + b1 = SCSCR_CKE1 + b0 = SCSCR_CKE0Quoted 1 line
What is that for exactly ?
What I can see from 3 different datasheets (sh7372, sh73a0, r8a7740) the first 2 bits differ in meaning.
Quoted 7 lines
On r8a7740 it depends: In asynchronous mode the first 2 bits CKE0/1 define whether you want to use an external clock to drive the baud generator or if you want to use the internal SUB clock. If you use the SUB clock you can further define if you want to use a subscaled SUB clock in the SCSMR register. In synchronous mode you must rely on the internal clock for the baud generator and can select if the SCK pin is used as clock input or output.
Quoted 3 lines
What about adding an optional source clock property to the bindings, that would contain the phandle of the source clock ? If the property is absent then the internal clock would be used.
We can't really use the internal oscillator at the moment, it's one of the things that is blocked on adoption of the common struct clk work. The baud rate generator algo will likewise differ depending on whether it's using an internally generated clock or not, which also makes a different set of baud rates available.
My plan originally was to wait until the common struct clk stuff came along well enough that we could provide a clock dynamically depending on the target baud (or for avoiding cpufreq pre/post-change notifier chains), but this obviously hasn't happened yet.
Quoted 8 lines
Quoted 3 lines
I think your idea for the abstraction with the phandle sounds like the right approach, but we aren't presently in a state where we can handle that.
Do the platforms that will be converted to DT currently need to make the clock source configurable ? If not we could just leave it out of the DT bindings until needed. Hopefully by then we'll have a common clock framework implementation.
The r8a7779 does use the external clock (according to my r8a7740 datasheet) while the other mainline SoCs use the internal one.
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Quoted 8 lines
Bit 2 and 3 don't exist in my datasheets.
The other bits define under which conditions you receive interrupts (send FIFO empty, receive FIFO full) and which bits you need to start transfers (one bit to start sending, one receiving). The bits 8 to 31 are used to set up DMA transfers and various interrupt events like error status and finish transfers. I haven't included them as they are not used in the driver.
Quoted 8 lines
Quoted 5 lines
Quoted 1 line
If they're not used maybe we can drop them :-)
Obviously they're used, otherwise they wouldn't be defined in the common header. Whether they are used by these specific CPUs or not isn't relevant, as there are plenty of cases where they are. grep harder.
My point is that if they're only used by arm/sh/* SoCs we don't need to support them in DT.
Assuming that SCSCR_TE and SCSCR_RE are always used and we could handle the clock flags with a phandle and the other flags are only used in the realtime domain (where we don't want DT support?), I suppose we could indeed drop the whole property - but we would have to wait. Otherwise it's not so shiny but we could get it merged now. I don't know how to proceed now, any decision makers here?
Cheers,
Bastian
Quoted 5 lines
--
Regards,Laurent Pinchart
PATCH v6 1/3 serial: sh-sci: Add OF support
Hi Bastian,
Quoted 74 lines · On Tuesday 19 March 2013 16:10:57 Bastian Hecht wrote:
2013/3/12 Laurent Pinchart <[email protected]>:
Quoted 43 lines · On Tuesday 12 March 2013 17:20:39 Paul Mundt wrote:
Quoted 42 lines · Laurent Pinchart
Quoted 26 lines · On Thursday 07 March 2013 11:26:29 Bastian Hecht wrote:
Quoted 17 lines
Quoted 12 lines
Review
Quoted 11 lines
+- renesas,scscr : Should contain a bitfield used by the Serial Control
Register.(quoted diff) +8
-0+ b7 = SCSCR_TIE + b6 = SCSCR_RIE + b5 = SCSCR_TE + b4 = SCSCR_RE + b3 = SCSCR_REIE + b2 = SCSCR_TOIE + b1 = SCSCR_CKE1 + b0 = SCSCR_CKE0Quoted 1 line
What is that for exactly ?
What I can see from 3 different datasheets (sh7372, sh73a0, r8a7740) the first 2 bits differ in meaning.
Quoted 7 lines
On r8a7740 it depends: In asynchronous mode the first 2 bits CKE0/1 define whether you want to use an external clock to drive the baud generator or if you want to use the internal SUB clock. If you use the SUB clock you can further define if you want to use a subscaled SUB clock in the SCSMR register. In synchronous mode you must rely on the internal clock for the baud generator and can select if the SCK pin is used as clock input or output.
Quoted 3 lines
What about adding an optional source clock property to the bindings, that would contain the phandle of the source clock ? If the property is absent then the internal clock would be used.
We can't really use the internal oscillator at the moment, it's one of the things that is blocked on adoption of the common struct clk work. The baud rate generator algo will likewise differ depending on whether it's using an internally generated clock or not, which also makes a different set of baud rates available.
My plan originally was to wait until the common struct clk stuff came along well enough that we could provide a clock dynamically depending on the target baud (or for avoiding cpufreq pre/post-change notifier chains), but this obviously hasn't happened yet.
Quoted 8 lines
Quoted 3 lines
I think your idea for the abstraction with the phandle sounds like the right approach, but we aren't presently in a state where we can handle that.
Do the platforms that will be converted to DT currently need to make the clock source configurable ? If not we could just leave it out of the DT bindings until needed. Hopefully by then we'll have a common clock framework implementation.
The r8a7779 does use the external clock (according to my r8a7740 datasheet) while the other mainline SoCs use the internal one.
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Quoted 8 lines
Bit 2 and 3 don't exist in my datasheets.
The other bits define under which conditions you receive interrupts (send FIFO empty, receive FIFO full) and which bits you need to start transfers (one bit to start sending, one receiving). The bits 8 to 31 are used to set up DMA transfers and various interrupt events like error status and finish transfers. I haven't included them as they are not used in the driver.
Quoted 8 lines
Quoted 5 lines
Quoted 1 line
If they're not used maybe we can drop them :-)
Obviously they're used, otherwise they wouldn't be defined in the common header. Whether they are used by these specific CPUs or not isn't relevant, as there are plenty of cases where they are. grep harder.
My point is that if they're only used by arm/sh/* SoCs we don't need to support them in DT.
Quoted 6 lines
Assuming that
SCSCR_TEandSCSCR_REare always used and we could handle the clock flags with a phandle and the other flags are only used in the realtime domain (where we don't want DT support?), I suppose we could indeed drop the whole property - but we would have to wait. Otherwise it's not so shiny but we could get it merged now. I don't know how to proceed now, any decision makers here?
My main concern is that DT bindings are ABIs that need to be supported forever. This is why I'd rather not add those flags to the DT bindings now only to deprecate them in a couple of kernel versions.
Signature · 3 lines
Regards, Laurent Pinchart