Skip to contentSkip to conversation

b43: implement basic TX power mgmt

PATCH Superseded Rafał Miłecki 5 participants 35 messages Mar 7, 2013 – Mar 19, 2013 Networking drivers (wireless)

lore
Share & tools
lore
#0 lore raw

cover b43: implement basic TX power mgmt

After spotting a lot of N-PHY-similar functions in BCM4331 dump of MMIO ops - split into names parts I was able to finally improve HT-PHY code.

It now sets TX basically, I can finally talk with devices that are few meters away, not just few centimetres. It's a little patch bomb, sorry for that, but I wasn't sure if my code is correct until it was complete and started working.

Rafa? Mi?ecki (13):
b43: HT-PHY: rename AFE defines
b43: HT-PHY: add classifier control function
b43: HT-PHY: move TX fix to the separated function
b43: HT-PHY: implement spurious tone avoidance
b43: HT-PHY: implement MAC reclocking
b43: HT-PHY: implement CCA reset
b43: HT-PHY: implement PA override
b43: HT-PHY: implement controlling TX power control
b43: HT-PHY: implement stopping sample tone playback
b43: HT-PHY: implement playing sample tone
b43: HT-PHY: implement RSSI polling
b43: HT-PHY: setup TX power control
b43: HT-PHY: enable basic TX power setup

 drivers/net/wireless/b43/phy_ht.c |  603 +++++++++++++++++++++++++++++++++----
 drivers/net/wireless/b43/phy_ht.h |   77 ++++-
 2 files changed, 613 insertions(+), 67 deletions(-)
Signature · 1 line
1.7.10.4
#1 lore raw

PATCH 1/13 b43: HT-PHY: rename AFE defines

It you take a look at N-PHY analog switch function it touches every core on the chipset. It seems HT-PHY does they same, it just has 3 cores instead of 2 (which make sense since BCM4331 is 3x3). Rename AFE defines to include core id.

---
 drivers/net/wireless/b43/phy_ht.c |   36 ++++++++++++++++++------------------
 drivers/net/wireless/b43/phy_ht.h |   12 ++++++------
 2 files changed, 24 insertions(+), 24 deletions(-)
drivers/net/wireless/b43/phy_ht.c +18 -18
index 3719a88..20c4cb7f 100644
@@ -177,9 +177,9 @@ static void b43_phy_ht_afe_unk1(struct b43_wldev *dev)
 	u8 i;
 
 	const u16 ctl_regs[3][2] = {
-		{ B43_PHY_HT_AFE_CTL1, B43_PHY_HT_AFE_CTL2 },
-		{ B43_PHY_HT_AFE_CTL3, B43_PHY_HT_AFE_CTL4 },
-		{ B43_PHY_HT_AFE_CTL5, B43_PHY_HT_AFE_CTL6},
+		{ B43_PHY_HT_AFE_C1_OVER, B43_PHY_HT_AFE_C1 },
+		{ B43_PHY_HT_AFE_C2_OVER, B43_PHY_HT_AFE_C2 },
+		{ B43_PHY_HT_AFE_C3_OVER, B43_PHY_HT_AFE_C3},
 	};
 
 	for (i = 0; i < 3; i++) {
@@ -362,9 +362,9 @@ static int b43_phy_ht_op_init(struct b43_wldev *dev)
 
 	b43_phy_mask(dev, B43_PHY_EXTG(0), ~0x3);
 
-	b43_phy_write(dev, B43_PHY_HT_AFE_CTL1, 0);
-	b43_phy_write(dev, B43_PHY_HT_AFE_CTL3, 0);
-	b43_phy_write(dev, B43_PHY_HT_AFE_CTL5, 0);
+	b43_phy_write(dev, B43_PHY_HT_AFE_C1_OVER, 0);
+	b43_phy_write(dev, B43_PHY_HT_AFE_C2_OVER, 0);
+	b43_phy_write(dev, B43_PHY_HT_AFE_C3_OVER, 0);
 
 	b43_phy_write(dev, B43_PHY_EXTG(0x103), 0x20);
 	b43_phy_write(dev, B43_PHY_EXTG(0x101), 0x20);
@@ -511,19 +511,19 @@ static void b43_phy_ht_op_software_rfkill(struct b43_wldev *dev,
 static void b43_phy_ht_op_switch_analog(struct b43_wldev *dev, bool on)
 {
 	if (on) {
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL2, 0x00cd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL1, 0x0000);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL4, 0x00cd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL3, 0x0000);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL6, 0x00cd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL5, 0x0000);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C1, 0x00cd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C1_OVER, 0x0000);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C2, 0x00cd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C2_OVER, 0x0000);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C3, 0x00cd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C3_OVER, 0x0000);
 	} else {
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL1, 0x07ff);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL2, 0x00fd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL3, 0x07ff);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL4, 0x00fd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL5, 0x07ff);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL6, 0x00fd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C1_OVER, 0x07ff);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C1, 0x00fd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C2_OVER, 0x07ff);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C2, 0x00fd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C3_OVER, 0x07ff);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C3, 0x00fd);
 	}
 }
 
drivers/net/wireless/b43/phy_ht.h +6 -6
index 6544c42..60824fa 100644
@@ -36,12 +36,12 @@
 
 #define B43_PHY_HT_RF_CTL1			B43_PHY_EXTG(0x010)
 
-#define B43_PHY_HT_AFE_CTL1			B43_PHY_EXTG(0x110)
-#define B43_PHY_HT_AFE_CTL2			B43_PHY_EXTG(0x111)
-#define B43_PHY_HT_AFE_CTL3			B43_PHY_EXTG(0x114)
-#define B43_PHY_HT_AFE_CTL4			B43_PHY_EXTG(0x115)
-#define B43_PHY_HT_AFE_CTL5			B43_PHY_EXTG(0x118)
-#define B43_PHY_HT_AFE_CTL6			B43_PHY_EXTG(0x119)
+#define B43_PHY_HT_AFE_C1_OVER			B43_PHY_EXTG(0x110)
+#define B43_PHY_HT_AFE_C1			B43_PHY_EXTG(0x111)
+#define B43_PHY_HT_AFE_C2_OVER			B43_PHY_EXTG(0x114)
+#define B43_PHY_HT_AFE_C2			B43_PHY_EXTG(0x115)
+#define B43_PHY_HT_AFE_C3_OVER			B43_PHY_EXTG(0x118)
+#define B43_PHY_HT_AFE_C3			B43_PHY_EXTG(0x119)
 
 
 /* Values for PHY registers used on channel switching */
Signature · 1 line
1.7.10.4
#2 lore raw

PATCH v3 1/13 b43: HT-PHY: rename AFE defines

It you take a look at N-PHY analog switch function it touches every core on the chipset. It seems HT-PHY does they same, it just has 3 cores instead of 2 (which make sense since BCM4331 is 3x3). Rename AFE defines to include core id.

---
V2: make ctl_regs array static btw
V3: use correct --in-reply-to

Sorry for using wrong In-Reply-To in V2 :(

---
 drivers/net/wireless/b43/phy_ht.c |   38 ++++++++++++++++++-------------------
 drivers/net/wireless/b43/phy_ht.h |   12 ++++++------
 2 files changed, 25 insertions(+), 25 deletions(-)
drivers/net/wireless/b43/phy_ht.c +19 -19
index 3719a88..df07c83 100644
@@ -176,10 +176,10 @@ static void b43_phy_ht_afe_unk1(struct b43_wldev *dev)
 {
 	u8 i;
 
-	const u16 ctl_regs[3][2] = {
-		{ B43_PHY_HT_AFE_CTL1, B43_PHY_HT_AFE_CTL2 },
-		{ B43_PHY_HT_AFE_CTL3, B43_PHY_HT_AFE_CTL4 },
-		{ B43_PHY_HT_AFE_CTL5, B43_PHY_HT_AFE_CTL6},
+	static const u16 ctl_regs[3][2] = {
+		{ B43_PHY_HT_AFE_C1_OVER, B43_PHY_HT_AFE_C1 },
+		{ B43_PHY_HT_AFE_C2_OVER, B43_PHY_HT_AFE_C2 },
+		{ B43_PHY_HT_AFE_C3_OVER, B43_PHY_HT_AFE_C3},
 	};
 
 	for (i = 0; i < 3; i++) {
@@ -362,9 +362,9 @@ static int b43_phy_ht_op_init(struct b43_wldev *dev)
 
 	b43_phy_mask(dev, B43_PHY_EXTG(0), ~0x3);
 
-	b43_phy_write(dev, B43_PHY_HT_AFE_CTL1, 0);
-	b43_phy_write(dev, B43_PHY_HT_AFE_CTL3, 0);
-	b43_phy_write(dev, B43_PHY_HT_AFE_CTL5, 0);
+	b43_phy_write(dev, B43_PHY_HT_AFE_C1_OVER, 0);
+	b43_phy_write(dev, B43_PHY_HT_AFE_C2_OVER, 0);
+	b43_phy_write(dev, B43_PHY_HT_AFE_C3_OVER, 0);
 
 	b43_phy_write(dev, B43_PHY_EXTG(0x103), 0x20);
 	b43_phy_write(dev, B43_PHY_EXTG(0x101), 0x20);
@@ -511,19 +511,19 @@ static void b43_phy_ht_op_software_rfkill(struct b43_wldev *dev,
 static void b43_phy_ht_op_switch_analog(struct b43_wldev *dev, bool on)
 {
 	if (on) {
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL2, 0x00cd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL1, 0x0000);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL4, 0x00cd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL3, 0x0000);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL6, 0x00cd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL5, 0x0000);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C1, 0x00cd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C1_OVER, 0x0000);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C2, 0x00cd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C2_OVER, 0x0000);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C3, 0x00cd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C3_OVER, 0x0000);
 	} else {
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL1, 0x07ff);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL2, 0x00fd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL3, 0x07ff);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL4, 0x00fd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL5, 0x07ff);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL6, 0x00fd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C1_OVER, 0x07ff);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C1, 0x00fd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C2_OVER, 0x07ff);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C2, 0x00fd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C3_OVER, 0x07ff);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C3, 0x00fd);
 	}
 }
 
drivers/net/wireless/b43/phy_ht.h +6 -6
index 6544c42..60824fa 100644
@@ -36,12 +36,12 @@
 
 #define B43_PHY_HT_RF_CTL1			B43_PHY_EXTG(0x010)
 
-#define B43_PHY_HT_AFE_CTL1			B43_PHY_EXTG(0x110)
-#define B43_PHY_HT_AFE_CTL2			B43_PHY_EXTG(0x111)
-#define B43_PHY_HT_AFE_CTL3			B43_PHY_EXTG(0x114)
-#define B43_PHY_HT_AFE_CTL4			B43_PHY_EXTG(0x115)
-#define B43_PHY_HT_AFE_CTL5			B43_PHY_EXTG(0x118)
-#define B43_PHY_HT_AFE_CTL6			B43_PHY_EXTG(0x119)
+#define B43_PHY_HT_AFE_C1_OVER			B43_PHY_EXTG(0x110)
+#define B43_PHY_HT_AFE_C1			B43_PHY_EXTG(0x111)
+#define B43_PHY_HT_AFE_C2_OVER			B43_PHY_EXTG(0x114)
+#define B43_PHY_HT_AFE_C2			B43_PHY_EXTG(0x115)
+#define B43_PHY_HT_AFE_C3_OVER			B43_PHY_EXTG(0x118)
+#define B43_PHY_HT_AFE_C3			B43_PHY_EXTG(0x119)
 
 
 /* Values for PHY registers used on channel switching */
Signature · 1 line
1.7.10.4
#3 lore raw

PATCH 2/13 b43: HT-PHY: add classifier control function

In reply to Rafał Miłecki

After comparing operations on reg 0xB on N and HT it seems to be the same register with similar ops. Implement them for HT-PHY.

---
 drivers/net/wireless/b43/phy_ht.c |   36 +++++++++++++++++++++++++++++++-----
 drivers/net/wireless/b43/phy_ht.h |    6 ++++++
 2 files changed, 37 insertions(+), 5 deletions(-)
drivers/net/wireless/b43/phy_ht.c +31 -5
index 20c4cb7f..2a65d01 100644
@@ -157,6 +157,22 @@ static void b43_radio_2059_init(struct b43_wldev *dev)
  * Various PHY ops
  **************************************************/
 
+static u16 b43_phy_ht_classifier(struct b43_wldev *dev, u16 mask, u16 val)
+{
+	u16 tmp;
+	u16 allowed = B43_PHY_HT_CLASS_CTL_CCK_EN |
+		      B43_PHY_HT_CLASS_CTL_OFDM_EN |
+		      B43_PHY_HT_CLASS_CTL_WAITED_EN;
+
+	tmp = b43_phy_read(dev, B43_PHY_HT_CLASS_CTL);
+	tmp &= allowed;
+	tmp &= ~mask;
+	tmp |= (val & mask);
+	b43_phy_maskset(dev, B43_PHY_HT_CLASS_CTL, ~allowed, tmp);
+
+	return tmp;
+}
+
 static void b43_phy_ht_zero_extg(struct b43_wldev *dev)
 {
 	u8 i, j;
@@ -264,7 +280,15 @@ static void b43_phy_ht_channel_setup(struct b43_wldev *dev,
 	b43_phy_write(dev, B43_PHY_HT_BW5, e->bw5);
 	b43_phy_write(dev, B43_PHY_HT_BW6, e->bw6);
 
-	/* TODO: some ops on PHY regs 0x0B0 and 0xC0A */
+	if (new_channel->hw_value == 14) {
+		b43_phy_ht_classifier(dev, B43_PHY_HT_CLASS_CTL_OFDM_EN, 0);
+		b43_phy_set(dev, B43_PHY_HT_TEST, 0x0800);
+	} else {
+		b43_phy_ht_classifier(dev, B43_PHY_HT_CLASS_CTL_OFDM_EN,
+				      B43_PHY_HT_CLASS_CTL_OFDM_EN);
+		if (new_channel->band == IEEE80211_BAND_2GHZ)
+			b43_phy_mask(dev, B43_PHY_HT_TEST, ~0x840);
+	}
 
 	/* TODO: separated function? */
 	for (i = 0; i < 3; i++) {
@@ -376,8 +400,11 @@ static int b43_phy_ht_op_init(struct b43_wldev *dev)
 	if (0) /* TODO: condition */
 		; /* TODO: PHY op on reg 0x217 */
 
-	b43_phy_read(dev, 0xb0); /* TODO: what for? */
-	b43_phy_set(dev, 0xb0, 0x1);
+	if (b43_current_band(dev->wl) == IEEE80211_BAND_5GHZ)
+		b43_phy_ht_classifier(dev, B43_PHY_HT_CLASS_CTL_CCK_EN, 0);
+	else
+		b43_phy_ht_classifier(dev, B43_PHY_HT_CLASS_CTL_CCK_EN,
+				      B43_PHY_HT_CLASS_CTL_CCK_EN);
 
 	b43_phy_set(dev, 0xb1, 0x91);
 	b43_phy_write(dev, 0x32f, 0x0003);
@@ -456,9 +483,8 @@ static int b43_phy_ht_op_init(struct b43_wldev *dev)
 	b43_phy_ht_force_rf_sequence(dev, B43_PHY_HT_RF_SEQ_TRIG_RX2TX);
 	b43_phy_ht_force_rf_sequence(dev, B43_PHY_HT_RF_SEQ_TRIG_RST2RX);
 
-	/* TODO: PHY op on reg 0xb0 */
-
 	/* TODO: Should we restore it? Or store it in global PHY info? */
+	b43_phy_ht_classifier(dev, 0, 0);
 	b43_phy_ht_read_clip_detection(dev, clip_state);
 
 	if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ)
drivers/net/wireless/b43/phy_ht.h +6 -0
index 60824fa..52603af 100644
@@ -12,6 +12,10 @@
 #define B43_PHY_HT_TABLE_ADDR			0x072 /* Table address */
 #define B43_PHY_HT_TABLE_DATALO			0x073 /* Table data low */
 #define B43_PHY_HT_TABLE_DATAHI			0x074 /* Table data high */
+#define B43_PHY_HT_CLASS_CTL			0x0B0 /* Classifier control */
+#define  B43_PHY_HT_CLASS_CTL_CCK_EN		0x0001 /* CCK enable */
+#define  B43_PHY_HT_CLASS_CTL_OFDM_EN		0x0002 /* OFDM enable */
+#define  B43_PHY_HT_CLASS_CTL_WAITED_EN		0x0004 /* Waited enable */
 #define B43_PHY_HT_BW1				0x1CE
 #define B43_PHY_HT_BW2				0x1CF
 #define B43_PHY_HT_BW3				0x1D0
@@ -43,6 +47,8 @@
 #define B43_PHY_HT_AFE_C3_OVER			B43_PHY_EXTG(0x118)
 #define B43_PHY_HT_AFE_C3			B43_PHY_EXTG(0x119)
 
+#define B43_PHY_HT_TEST				B43_PHY_N_BMODE(0x00A)
+
 
 /* Values for PHY registers used on channel switching */
 struct b43_phy_ht_channeltab_e_phy {
Signature · 1 line
1.7.10.4
#4 lore raw

PATCH 3/13 b43: HT-PHY: move TX fix to the separated function

In reply to Rafał Miłecki

On N-PHY after B43_PHY_B_TEST operation there is a call to TX power fix function which iterates over available cores. It matches our HT-PHY code which means it's probably also some TX fix.

---
 drivers/net/wireless/b43/phy_ht.c |   46 ++++++++++++++++++++++---------------
 1 file changed, 28 insertions(+), 18 deletions(-)
drivers/net/wireless/b43/phy_ht.c +28 -18
index 2a65d01..f7463aa 100644
@@ -256,6 +256,32 @@ static void b43_phy_ht_bphy_init(struct b43_wldev *dev)
 }
 
 /**************************************************
+ * Tx/Rx
+ **************************************************/
+
+static void b43_phy_ht_tx_power_fix(struct b43_wldev *dev)
+{
+	int i;
+
+	for (i = 0; i < 3; i++) {
+		u16 mask;
+		u32 tmp = b43_httab_read(dev, B43_HTTAB32(26, 0xE8));
+
+		if (0) /* FIXME */
+			mask = 0x2 << (i * 4);
+		else
+			mask = 0;
+		b43_phy_mask(dev, B43_PHY_EXTG(0x108), mask);
+
+		b43_httab_write(dev, B43_HTTAB16(7, 0x110 + i), tmp >> 16);
+		b43_httab_write(dev, B43_HTTAB8(13, 0x63 + (i * 4)),
+				tmp & 0xFF);
+		b43_httab_write(dev, B43_HTTAB8(13, 0x73 + (i * 4)),
+				tmp & 0xFF);
+	}
+}
+
+/**************************************************
  * Channel switching ops.
  **************************************************/
 
@@ -264,7 +290,6 @@ static void b43_phy_ht_channel_setup(struct b43_wldev *dev,
 				struct ieee80211_channel *new_channel)
 {
 	bool old_band_5ghz;
-	u8 i;
 
 	old_band_5ghz = b43_phy_read(dev, B43_PHY_HT_BANDCTL) & 0; /* FIXME */
 	if (new_channel->band == IEEE80211_BAND_5GHZ && !old_band_5ghz) {
@@ -290,23 +315,8 @@ static void b43_phy_ht_channel_setup(struct b43_wldev *dev,
 			b43_phy_mask(dev, B43_PHY_HT_TEST, ~0x840);
 	}
 
-	/* TODO: separated function? */
-	for (i = 0; i < 3; i++) {
-		u16 mask;
-		u32 tmp = b43_httab_read(dev, B43_HTTAB32(26, 0xE8));
-
-		if (0) /* FIXME */
-			mask = 0x2 << (i * 4);
-		else
-			mask = 0;
-		b43_phy_mask(dev, B43_PHY_EXTG(0x108), mask);
-
-		b43_httab_write(dev, B43_HTTAB16(7, 0x110 + i), tmp >> 16);
-		b43_httab_write(dev, B43_HTTAB8(13, 0x63 + (i * 4)),
-				tmp & 0xFF);
-		b43_httab_write(dev, B43_HTTAB8(13, 0x73 + (i * 4)),
-				tmp & 0xFF);
-	}
+	if (1) /* TODO: On N it's for early devices only, what about HT? */
+		b43_phy_ht_tx_power_fix(dev);
 
 	b43_phy_write(dev, 0x017e, 0x3830);
 }
Signature · 1 line
1.7.10.4
#5 lore raw

PATCH 4/13 b43: HT-PHY: implement spurious tone avoidance

In reply to Rafał Miłecki

On N-PHY it's also done after TX power fix, so it was easy to spot. Unfortunately the MMIO logs I have from ndsiwrapper include channels 1-12 only, so enabling code for 13 and 14 is just a N-PHY-based guess.

---
 drivers/net/wireless/b43/phy_ht.c |   20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)
drivers/net/wireless/b43/phy_ht.c +20 -0
index f7463aa..4ccd371 100644
@@ -285,6 +285,24 @@ static void b43_phy_ht_tx_power_fix(struct b43_wldev *dev)
  * Channel switching ops.
  **************************************************/
 
+static void b43_phy_ht_spur_avoid(struct b43_wldev *dev,
+				  struct ieee80211_channel *new_channel)
+{
+	struct bcma_device *core = dev->dev->bdev;
+	int spuravoid = 0;
+
+	/* Check for 13 and 14 is just a guess, we don't have enough logs. */
+	if (new_channel->hw_value == 13 || new_channel->hw_value == 14)
+		spuravoid = 1;
+	bcma_core_pll_ctl(core, B43_BCMA_CLKCTLST_PHY_PLL_REQ, 0, false);
+	bcma_pmu_spuravoid_pllupdate(&core->bus->drv_cc, spuravoid);
+	bcma_core_pll_ctl(core,
+			  B43_BCMA_CLKCTLST_80211_PLL_REQ |
+			  B43_BCMA_CLKCTLST_PHY_PLL_REQ,
+			  B43_BCMA_CLKCTLST_80211_PLL_ST |
+			  B43_BCMA_CLKCTLST_PHY_PLL_ST, false);
+}
+
 static void b43_phy_ht_channel_setup(struct b43_wldev *dev,
 				const struct b43_phy_ht_channeltab_e_phy *e,
 				struct ieee80211_channel *new_channel)
@@ -318,6 +336,8 @@ static void b43_phy_ht_channel_setup(struct b43_wldev *dev,
 	if (1) /* TODO: On N it's for early devices only, what about HT? */
 		b43_phy_ht_tx_power_fix(dev);
 
+	b43_phy_ht_spur_avoid(dev, new_channel);
+
 	b43_phy_write(dev, 0x017e, 0x3830);
 }
 
Signature · 1 line
1.7.10.4
#6 lore raw

PATCH 5/13 b43: HT-PHY: implement MAC reclocking

In reply to Rafał Miłecki
---
 drivers/net/wireless/b43/phy_ht.c |   18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
drivers/net/wireless/b43/phy_ht.c +18 -0
index 4ccd371..4b24816 100644
@@ -290,6 +290,7 @@ static void b43_phy_ht_spur_avoid(struct b43_wldev *dev,
 {
 	struct bcma_device *core = dev->dev->bdev;
 	int spuravoid = 0;
+	u16 tmp;
 
 	/* Check for 13 and 14 is just a guess, we don't have enough logs. */
 	if (new_channel->hw_value == 13 || new_channel->hw_value == 14)
@@ -301,6 +302,23 @@ static void b43_phy_ht_spur_avoid(struct b43_wldev *dev,
 			  B43_BCMA_CLKCTLST_PHY_PLL_REQ,
 			  B43_BCMA_CLKCTLST_80211_PLL_ST |
 			  B43_BCMA_CLKCTLST_PHY_PLL_ST, false);
+
+	/* Values has been taken from wlc_bmac_switch_macfreq comments */
+	switch (spuravoid) {
+	case 2: /* 126MHz */
+		tmp = 0x2082;
+		break;
+	case 1: /* 123MHz */
+		tmp = 0x5341;
+		break;
+	default: /* 120MHz */
+		tmp = 0x8889;
+	}
+
+	b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_LOW, tmp);
+	b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x8);
+
+	/* TODO: reset PLL */
 }
 
 static void b43_phy_ht_channel_setup(struct b43_wldev *dev,
Signature · 1 line
1.7.10.4
#7 lore raw

PATCH 6/13 b43: HT-PHY: implement CCA reset

In reply to Rafał Miłecki

It was just another similar-to-N-PHY and easy-to-track routine:
write32 0xb0601408 <- 0x00002057
phy_read(0x0001) -> 0x0000
phy_write(0x0001) <- 0x4000
phy_write(0x0001) <- 0x0000
write32 0xb0601408 <- 0x00002055 (b43_phy_ht_force_rf_sequence was moved up unmodified)

---
P.S.
There is a "msleep" usage warning, but it's in the code I just move. Will fix sleeps/waits later globally.

---
 drivers/net/wireless/b43/phy_ht.c |   68 +++++++++++++++++++++++++------------
 1 file changed, 47 insertions(+), 21 deletions(-)
drivers/net/wireless/b43/phy_ht.c +47 -21
index 4b24816..aedbae7 100644
@@ -154,6 +154,31 @@ static void b43_radio_2059_init(struct b43_wldev *dev)
 }
 
 /**************************************************
+ * RF
+ **************************************************/
+
+static void b43_phy_ht_force_rf_sequence(struct b43_wldev *dev, u16 rf_seq)
+{
+	u8 i;
+
+	u16 save_seq_mode = b43_phy_read(dev, B43_PHY_HT_RF_SEQ_MODE);
+	b43_phy_set(dev, B43_PHY_HT_RF_SEQ_MODE, 0x3);
+
+	b43_phy_set(dev, B43_PHY_HT_RF_SEQ_TRIG, rf_seq);
+	for (i = 0; i < 200; i++) {
+		if (!(b43_phy_read(dev, B43_PHY_HT_RF_SEQ_STATUS) & rf_seq)) {
+			i = 0;
+			break;
+		}
+		msleep(1);
+	}
+	if (i)
+		b43err(dev->wl, "Forcing RF sequence timeout\n");
+
+	b43_phy_write(dev, B43_PHY_HT_RF_SEQ_MODE, save_seq_mode);
+}
+
+/**************************************************
  * Various PHY ops
  **************************************************/
 
@@ -173,6 +198,20 @@ static u16 b43_phy_ht_classifier(struct b43_wldev *dev, u16 mask, u16 val)
 	return tmp;
 }
 
+static void b43_phy_ht_reset_cca(struct b43_wldev *dev)
+{
+	u16 bbcfg;
+
+	b43_phy_force_clock(dev, true);
+	bbcfg = b43_phy_read(dev, B43_PHY_HT_BBCFG);
+	b43_phy_write(dev, B43_PHY_HT_BBCFG, bbcfg | B43_PHY_HT_BBCFG_RSTCCA);
+	udelay(1);
+	b43_phy_write(dev, B43_PHY_HT_BBCFG, bbcfg & ~B43_PHY_HT_BBCFG_RSTCCA);
+	b43_phy_force_clock(dev, false);
+
+	b43_phy_ht_force_rf_sequence(dev, B43_PHY_HT_RF_SEQ_TRIG_RST2RX);
+}
+
 static void b43_phy_ht_zero_extg(struct b43_wldev *dev)
 {
 	u8 i, j;
@@ -209,27 +248,6 @@ static void b43_phy_ht_afe_unk1(struct b43_wldev *dev)
 	}
 }
 
-static void b43_phy_ht_force_rf_sequence(struct b43_wldev *dev, u16 rf_seq)
-{
-	u8 i;
-
-	u16 save_seq_mode = b43_phy_read(dev, B43_PHY_HT_RF_SEQ_MODE);
-	b43_phy_set(dev, B43_PHY_HT_RF_SEQ_MODE, 0x3);
-
-	b43_phy_set(dev, B43_PHY_HT_RF_SEQ_TRIG, rf_seq);
-	for (i = 0; i < 200; i++) {
-		if (!(b43_phy_read(dev, B43_PHY_HT_RF_SEQ_STATUS) & rf_seq)) {
-			i = 0;
-			break;
-		}
-		msleep(1);
-	}
-	if (i)
-		b43err(dev->wl, "Forcing RF sequence timeout\n");
-
-	b43_phy_write(dev, B43_PHY_HT_RF_SEQ_MODE, save_seq_mode);
-}
-
 static void b43_phy_ht_read_clip_detection(struct b43_wldev *dev, u16 *clip_st)
 {
 	clip_st[0] = b43_phy_read(dev, B43_PHY_HT_C1_CLIP1THRES);
@@ -319,6 +337,14 @@ static void b43_phy_ht_spur_avoid(struct b43_wldev *dev,
 	b43_write16(dev, B43_MMIO_TSF_CLK_FRAC_HIGH, 0x8);
 
 	/* TODO: reset PLL */
+
+	if (spuravoid)
+		b43_phy_set(dev, B43_PHY_HT_BBCFG, B43_PHY_HT_BBCFG_RSTRX);
+	else
+		b43_phy_mask(dev, B43_PHY_HT_BBCFG,
+				~B43_PHY_HT_BBCFG_RSTRX & 0xFFFF);
+
+	b43_phy_ht_reset_cca(dev);
 }
 
 static void b43_phy_ht_channel_setup(struct b43_wldev *dev,
Signature · 1 line
1.7.10.4
#8 lore raw

PATCH 7/13 b43: HT-PHY: implement PA override

In reply to Rafał Miłecki
---
 drivers/net/wireless/b43/phy_ht.c |   22 ++++++++++++++++++++++
 drivers/net/wireless/b43/phy_ht.h |    5 +++++
 2 files changed, 27 insertions(+)
drivers/net/wireless/b43/phy_ht.c +22 -0
index aedbae7..3b3517c 100644
@@ -178,6 +178,26 @@ static void b43_phy_ht_force_rf_sequence(struct b43_wldev *dev, u16 rf_seq)
 	b43_phy_write(dev, B43_PHY_HT_RF_SEQ_MODE, save_seq_mode);
 }
 
+static void b43_phy_ht_pa_override(struct b43_wldev *dev, bool enable)
+{
+	struct b43_phy_ht *htphy = dev->phy.ht;
+	const u16 regs[3] = { B43_PHY_HT_RF_CTL_INT_C1,
+				  B43_PHY_HT_RF_CTL_INT_C2,
+				  B43_PHY_HT_RF_CTL_INT_C3 };
+	int i;
+
+	if (enable) {
+		for (i = 0; i < 3; i++)
+			b43_phy_write(dev, regs[i], htphy->rf_ctl_int_save[i]);
+	} else {
+		for (i = 0; i < 3; i++)
+			htphy->rf_ctl_int_save[i] = b43_phy_read(dev, regs[i]);
+		/* TODO: Does 5GHz band use different value (not 0x0400)? */
+		for (i = 0; i < 3; i++)
+			b43_phy_write(dev, regs[i], 0x0400);
+	}
+}
+
 /**************************************************
  * Various PHY ops
  **************************************************/
@@ -554,8 +574,10 @@ static int b43_phy_ht_op_init(struct b43_wldev *dev)
 
 	b43_mac_phy_clock_set(dev, true);
 
+	b43_phy_ht_pa_override(dev, false);
 	b43_phy_ht_force_rf_sequence(dev, B43_PHY_HT_RF_SEQ_TRIG_RX2TX);
 	b43_phy_ht_force_rf_sequence(dev, B43_PHY_HT_RF_SEQ_TRIG_RST2RX);
+	b43_phy_ht_pa_override(dev, true);
 
 	/* TODO: Should we restore it? Or store it in global PHY info? */
 	b43_phy_ht_classifier(dev, 0, 0);
drivers/net/wireless/b43/phy_ht.h +5 -0
index 52603af..684807c 100644
@@ -40,6 +40,10 @@
 
 #define B43_PHY_HT_RF_CTL1			B43_PHY_EXTG(0x010)
 
+#define B43_PHY_HT_RF_CTL_INT_C1		B43_PHY_EXTG(0x04c)
+#define B43_PHY_HT_RF_CTL_INT_C2		B43_PHY_EXTG(0x06c)
+#define B43_PHY_HT_RF_CTL_INT_C3		B43_PHY_EXTG(0x08c)
+
 #define B43_PHY_HT_AFE_C1_OVER			B43_PHY_EXTG(0x110)
 #define B43_PHY_HT_AFE_C1			B43_PHY_EXTG(0x111)
 #define B43_PHY_HT_AFE_C2_OVER			B43_PHY_EXTG(0x114)
@@ -62,6 +66,7 @@ struct b43_phy_ht_channeltab_e_phy {
 
 
 struct b43_phy_ht {
+	u16 rf_ctl_int_save[3];
 };
 
 
Signature · 1 line
1.7.10.4
#9 lore raw

PATCH v2 7/13 b43: HT-PHY: implement PA override

---
V2: use static for "regs" array

---
 drivers/net/wireless/b43/phy_ht.c |   22 ++++++++++++++++++++++
 drivers/net/wireless/b43/phy_ht.h |    5 +++++
 2 files changed, 27 insertions(+)
drivers/net/wireless/b43/phy_ht.c +22 -0
index 23a46c6..1998dca 100644
@@ -178,6 +178,26 @@ static void b43_phy_ht_force_rf_sequence(struct b43_wldev *dev, u16 rf_seq)
 	b43_phy_write(dev, B43_PHY_HT_RF_SEQ_MODE, save_seq_mode);
 }
 
+static void b43_phy_ht_pa_override(struct b43_wldev *dev, bool enable)
+{
+	struct b43_phy_ht *htphy = dev->phy.ht;
+	static const u16 regs[3] = { B43_PHY_HT_RF_CTL_INT_C1,
+				     B43_PHY_HT_RF_CTL_INT_C2,
+				     B43_PHY_HT_RF_CTL_INT_C3 };
+	int i;
+
+	if (enable) {
+		for (i = 0; i < 3; i++)
+			b43_phy_write(dev, regs[i], htphy->rf_ctl_int_save[i]);
+	} else {
+		for (i = 0; i < 3; i++)
+			htphy->rf_ctl_int_save[i] = b43_phy_read(dev, regs[i]);
+		/* TODO: Does 5GHz band use different value (not 0x0400)? */
+		for (i = 0; i < 3; i++)
+			b43_phy_write(dev, regs[i], 0x0400);
+	}
+}
+
 /**************************************************
  * Various PHY ops
  **************************************************/
@@ -554,8 +574,10 @@ static int b43_phy_ht_op_init(struct b43_wldev *dev)
 
 	b43_mac_phy_clock_set(dev, true);
 
+	b43_phy_ht_pa_override(dev, false);
 	b43_phy_ht_force_rf_sequence(dev, B43_PHY_HT_RF_SEQ_TRIG_RX2TX);
 	b43_phy_ht_force_rf_sequence(dev, B43_PHY_HT_RF_SEQ_TRIG_RST2RX);
+	b43_phy_ht_pa_override(dev, true);
 
 	/* TODO: Should we restore it? Or store it in global PHY info? */
 	b43_phy_ht_classifier(dev, 0, 0);
drivers/net/wireless/b43/phy_ht.h +5 -0
index 52603af..684807c 100644
@@ -40,6 +40,10 @@
 
 #define B43_PHY_HT_RF_CTL1			B43_PHY_EXTG(0x010)
 
+#define B43_PHY_HT_RF_CTL_INT_C1		B43_PHY_EXTG(0x04c)
+#define B43_PHY_HT_RF_CTL_INT_C2		B43_PHY_EXTG(0x06c)
+#define B43_PHY_HT_RF_CTL_INT_C3		B43_PHY_EXTG(0x08c)
+
 #define B43_PHY_HT_AFE_C1_OVER			B43_PHY_EXTG(0x110)
 #define B43_PHY_HT_AFE_C1			B43_PHY_EXTG(0x111)
 #define B43_PHY_HT_AFE_C2_OVER			B43_PHY_EXTG(0x114)
@@ -62,6 +66,7 @@ struct b43_phy_ht_channeltab_e_phy {
 
 
 struct b43_phy_ht {
+	u16 rf_ctl_int_save[3];
 };
 
 
Signature · 1 line
1.7.10.4
#10 lore raw

PATCH 8/13 b43: HT-PHY: implement controlling TX power control

In reply to Rafał Miłecki

Don't enable it until we have (almost?) whole TX power management figured out. It's similar to the N-PHY, the difference is that we call a "fix" *before* disabling power control.

---
 drivers/net/wireless/b43/phy_ht.c |   55 +++++++++++++++++++++++++++++++++++++
 drivers/net/wireless/b43/phy_ht.h |   13 +++++++++
 2 files changed, 68 insertions(+)
drivers/net/wireless/b43/phy_ht.c +55 -0
index 3b3517c..4300867 100644
@@ -319,6 +319,46 @@ static void b43_phy_ht_tx_power_fix(struct b43_wldev *dev)
 	}
 }
 
+#if 0
+static void b43_phy_ht_tx_power_ctl(struct b43_wldev *dev, bool enable)
+{
+	struct b43_phy_ht *phy_ht = dev->phy.ht;
+	u16 en_bits = B43_PHY_HT_TXPCTL_CMD_C1_COEFF |
+		      B43_PHY_HT_TXPCTL_CMD_C1_HWPCTLEN |
+		      B43_PHY_HT_TXPCTL_CMD_C1_PCTLEN;
+	const u16 cmd_regs[3] = { B43_PHY_HT_TXPCTL_CMD_C1,
+				  B43_PHY_HT_TXPCTL_CMD_C2,
+				  B43_PHY_HT_TXPCTL_CMD_C3 };
+	int i;
+
+	if (!enable) {
+		if (b43_phy_read(dev, B43_PHY_HT_TXPCTL_CMD_C1) & en_bits) {
+			/* We disable enabled TX pwr ctl, save it's state */
+			/*
+			 * TODO: find the registers. On N-PHY they were 0x1ed
+			 * and 0x1ee, we need 3 such a registers for HT-PHY
+			 */
+		}
+		b43_phy_mask(dev, B43_PHY_HT_TXPCTL_CMD_C1, ~en_bits);
+	} else {
+		b43_phy_set(dev, B43_PHY_HT_TXPCTL_CMD_C1, en_bits);
+
+		if (b43_current_band(dev->wl) == IEEE80211_BAND_5GHZ) {
+			for (i = 0; i < 3; i++)
+				b43_phy_write(dev, cmd_regs[i], 0x32);
+		}
+
+		for (i = 0; i < 3; i++)
+			if (phy_ht->tx_pwr_idx[i] <=
+			    B43_PHY_HT_TXPCTL_CMD_C1_INIT)
+				b43_phy_write(dev, cmd_regs[i],
+					      phy_ht->tx_pwr_idx[i]);
+	}
+
+	phy_ht->tx_pwr_ctl = enable;
+}
+#endif
+
 /**************************************************
  * Channel switching ops.
  **************************************************/
@@ -455,14 +495,21 @@ static void b43_phy_ht_op_prepare_structs(struct b43_wldev *dev)
 {
 	struct b43_phy *phy = &dev->phy;
 	struct b43_phy_ht *phy_ht = phy->ht;
+	int i;
 
 	memset(phy_ht, 0, sizeof(*phy_ht));
+
+	phy_ht->tx_pwr_ctl = true;
+	for (i = 0; i < 3; i++)
+		phy_ht->tx_pwr_idx[i] = B43_PHY_HT_TXPCTL_CMD_C1_INIT + 1;
 }
 
 static int b43_phy_ht_op_init(struct b43_wldev *dev)
 {
+	struct b43_phy_ht *phy_ht = dev->phy.ht;
 	u16 tmp;
 	u16 clip_state[3];
+	bool saved_tx_pwr_ctl;
 
 	if (dev->dev->bus_type != B43_BUS_BCMA) {
 		b43err(dev->wl, "HT-PHY is supported only on BCMA bus!\n");
@@ -589,6 +636,14 @@ static int b43_phy_ht_op_init(struct b43_wldev *dev)
 	b43_httab_write_bulk(dev, B43_HTTAB32(0x1a, 0xc0),
 			B43_HTTAB_1A_C0_LATE_SIZE, b43_httab_0x1a_0xc0_late);
 
+	saved_tx_pwr_ctl = phy_ht->tx_pwr_ctl;
+	b43_phy_ht_tx_power_fix(dev);
+#if 0
+	b43_phy_ht_tx_power_ctl(dev, false);
+	/* TODO */
+	b43_phy_ht_tx_power_ctl(dev, saved_tx_pwr_ctl);
+#endif
+
 	return 0;
 }
 
drivers/net/wireless/b43/phy_ht.h +13 -0
index 684807c..bc7a43f 100644
@@ -22,6 +22,13 @@
 #define B43_PHY_HT_BW4				0x1D1
 #define B43_PHY_HT_BW5				0x1D2
 #define B43_PHY_HT_BW6				0x1D3
+#define B43_PHY_HT_TXPCTL_CMD_C1		0x1E7	/* TX power control command */
+#define  B43_PHY_HT_TXPCTL_CMD_C1_INIT		0x007F	/* Init */
+#define  B43_PHY_HT_TXPCTL_CMD_C1_COEFF		0x2000	/* Power control coefficients */
+#define  B43_PHY_HT_TXPCTL_CMD_C1_HWPCTLEN	0x4000	/* Hardware TX power control enable */
+#define  B43_PHY_HT_TXPCTL_CMD_C1_PCTLEN	0x8000	/* TX power control enable */
+#define B43_PHY_HT_TXPCTL_CMD_C2		0x222
+#define  B43_PHY_HT_TXPCTL_CMD_C2_INIT		0x007F
 
 #define B43_PHY_HT_C1_CLIP1THRES		B43_PHY_OFDM(0x00E)
 #define B43_PHY_HT_C2_CLIP1THRES		B43_PHY_OFDM(0x04E)
@@ -51,6 +58,9 @@
 #define B43_PHY_HT_AFE_C3_OVER			B43_PHY_EXTG(0x118)
 #define B43_PHY_HT_AFE_C3			B43_PHY_EXTG(0x119)
 
+#define B43_PHY_HT_TXPCTL_CMD_C3		B43_PHY_EXTG(0x164)
+#define  B43_PHY_HT_TXPCTL_CMD_C3_INIT		0x007F
+
 #define B43_PHY_HT_TEST				B43_PHY_N_BMODE(0x00A)
 
 
@@ -67,6 +77,9 @@ struct b43_phy_ht_channeltab_e_phy {
 
 struct b43_phy_ht {
 	u16 rf_ctl_int_save[3];
+
+	bool tx_pwr_ctl;
+	u8 tx_pwr_idx[3];
 };
 
 
Signature · 1 line
1.7.10.4
#11 lore raw

PATCH v2 8/13 b43: HT-PHY: implement controlling TX power control

Don't enable it until we have (almost?) whole TX power management figured out. It's similar to the N-PHY, the difference is that we call a "fix" *before* disabling power control.

---
V2: use static for cmd_regs array

---
 drivers/net/wireless/b43/phy_ht.c |   55 +++++++++++++++++++++++++++++++++++++
 drivers/net/wireless/b43/phy_ht.h |   13 +++++++++
 2 files changed, 68 insertions(+)
drivers/net/wireless/b43/phy_ht.c +55 -0
index 1998dca..1663551 100644
@@ -319,6 +319,46 @@ static void b43_phy_ht_tx_power_fix(struct b43_wldev *dev)
 	}
 }
 
+#if 0
+static void b43_phy_ht_tx_power_ctl(struct b43_wldev *dev, bool enable)
+{
+	struct b43_phy_ht *phy_ht = dev->phy.ht;
+	u16 en_bits = B43_PHY_HT_TXPCTL_CMD_C1_COEFF |
+		      B43_PHY_HT_TXPCTL_CMD_C1_HWPCTLEN |
+		      B43_PHY_HT_TXPCTL_CMD_C1_PCTLEN;
+	static const u16 cmd_regs[3] = { B43_PHY_HT_TXPCTL_CMD_C1,
+					 B43_PHY_HT_TXPCTL_CMD_C2,
+					 B43_PHY_HT_TXPCTL_CMD_C3 };
+	int i;
+
+	if (!enable) {
+		if (b43_phy_read(dev, B43_PHY_HT_TXPCTL_CMD_C1) & en_bits) {
+			/* We disable enabled TX pwr ctl, save it's state */
+			/*
+			 * TODO: find the registers. On N-PHY they were 0x1ed
+			 * and 0x1ee, we need 3 such a registers for HT-PHY
+			 */
+		}
+		b43_phy_mask(dev, B43_PHY_HT_TXPCTL_CMD_C1, ~en_bits);
+	} else {
+		b43_phy_set(dev, B43_PHY_HT_TXPCTL_CMD_C1, en_bits);
+
+		if (b43_current_band(dev->wl) == IEEE80211_BAND_5GHZ) {
+			for (i = 0; i < 3; i++)
+				b43_phy_write(dev, cmd_regs[i], 0x32);
+		}
+
+		for (i = 0; i < 3; i++)
+			if (phy_ht->tx_pwr_idx[i] <=
+			    B43_PHY_HT_TXPCTL_CMD_C1_INIT)
+				b43_phy_write(dev, cmd_regs[i],
+					      phy_ht->tx_pwr_idx[i]);
+	}
+
+	phy_ht->tx_pwr_ctl = enable;
+}
+#endif
+
 /**************************************************
  * Channel switching ops.
  **************************************************/
@@ -455,14 +495,21 @@ static void b43_phy_ht_op_prepare_structs(struct b43_wldev *dev)
 {
 	struct b43_phy *phy = &dev->phy;
 	struct b43_phy_ht *phy_ht = phy->ht;
+	int i;
 
 	memset(phy_ht, 0, sizeof(*phy_ht));
+
+	phy_ht->tx_pwr_ctl = true;
+	for (i = 0; i < 3; i++)
+		phy_ht->tx_pwr_idx[i] = B43_PHY_HT_TXPCTL_CMD_C1_INIT + 1;
 }
 
 static int b43_phy_ht_op_init(struct b43_wldev *dev)
 {
+	struct b43_phy_ht *phy_ht = dev->phy.ht;
 	u16 tmp;
 	u16 clip_state[3];
+	bool saved_tx_pwr_ctl;
 
 	if (dev->dev->bus_type != B43_BUS_BCMA) {
 		b43err(dev->wl, "HT-PHY is supported only on BCMA bus!\n");
@@ -589,6 +636,14 @@ static int b43_phy_ht_op_init(struct b43_wldev *dev)
 	b43_httab_write_bulk(dev, B43_HTTAB32(0x1a, 0xc0),
 			B43_HTTAB_1A_C0_LATE_SIZE, b43_httab_0x1a_0xc0_late);
 
+	saved_tx_pwr_ctl = phy_ht->tx_pwr_ctl;
+	b43_phy_ht_tx_power_fix(dev);
+#if 0
+	b43_phy_ht_tx_power_ctl(dev, false);
+	/* TODO */
+	b43_phy_ht_tx_power_ctl(dev, saved_tx_pwr_ctl);
+#endif
+
 	return 0;
 }
 
drivers/net/wireless/b43/phy_ht.h +13 -0
index 684807c..bc7a43f 100644
@@ -22,6 +22,13 @@
 #define B43_PHY_HT_BW4				0x1D1
 #define B43_PHY_HT_BW5				0x1D2
 #define B43_PHY_HT_BW6				0x1D3
+#define B43_PHY_HT_TXPCTL_CMD_C1		0x1E7	/* TX power control command */
+#define  B43_PHY_HT_TXPCTL_CMD_C1_INIT		0x007F	/* Init */
+#define  B43_PHY_HT_TXPCTL_CMD_C1_COEFF		0x2000	/* Power control coefficients */
+#define  B43_PHY_HT_TXPCTL_CMD_C1_HWPCTLEN	0x4000	/* Hardware TX power control enable */
+#define  B43_PHY_HT_TXPCTL_CMD_C1_PCTLEN	0x8000	/* TX power control enable */
+#define B43_PHY_HT_TXPCTL_CMD_C2		0x222
+#define  B43_PHY_HT_TXPCTL_CMD_C2_INIT		0x007F
 
 #define B43_PHY_HT_C1_CLIP1THRES		B43_PHY_OFDM(0x00E)
 #define B43_PHY_HT_C2_CLIP1THRES		B43_PHY_OFDM(0x04E)
@@ -51,6 +58,9 @@
 #define B43_PHY_HT_AFE_C3_OVER			B43_PHY_EXTG(0x118)
 #define B43_PHY_HT_AFE_C3			B43_PHY_EXTG(0x119)
 
+#define B43_PHY_HT_TXPCTL_CMD_C3		B43_PHY_EXTG(0x164)
+#define  B43_PHY_HT_TXPCTL_CMD_C3_INIT		0x007F
+
 #define B43_PHY_HT_TEST				B43_PHY_N_BMODE(0x00A)
 
 
@@ -67,6 +77,9 @@ struct b43_phy_ht_channeltab_e_phy {
 
 struct b43_phy_ht {
 	u16 rf_ctl_int_save[3];
+
+	bool tx_pwr_ctl;
+	u8 tx_pwr_idx[3];
 };
 
 
Signature · 1 line
1.7.10.4
#12 lore raw

PATCH 9/13 b43: HT-PHY: implement stopping sample tone playback

In reply to Rafał Miłecki

It was another sequence I recognized in HT-PHY dump:
phy_read(0x00c7) -> 0x0001
phy_read(0x00c3) -> 0x0000
phy_write(0x00c3) <- 0x0002
phy_read(0x00c3) -> 0x0000
phy_write(0x00c3) <- 0x0000
The difference to N-PHY is that it writes to 6 tables instead of a one (after above).

---
 drivers/net/wireless/b43/phy_ht.c |   41 +++++++++++++++++++++++++++++++++++++
 drivers/net/wireless/b43/phy_ht.h |    6 ++++++
 2 files changed, 47 insertions(+)
drivers/net/wireless/b43/phy_ht.c +41 -0
index 4300867..8e5d5bd 100644
@@ -294,6 +294,36 @@ static void b43_phy_ht_bphy_init(struct b43_wldev *dev)
 }
 
 /**************************************************
+ * Samples
+ **************************************************/
+
+#if 0
+static void b43_phy_ht_stop_playback(struct b43_wldev *dev)
+{
+	struct b43_phy_ht *phy_ht = dev->phy.ht;
+	u16 tmp;
+	int i;
+
+	tmp = b43_phy_read(dev, B43_PHY_HT_SAMP_STAT);
+	if (tmp & 0x1)
+		b43_phy_set(dev, B43_PHY_HT_SAMP_CMD, B43_PHY_HT_SAMP_CMD_STOP);
+	else if (tmp & 0x2)
+		b43_phy_mask(dev, B43_PHY_HT_IQLOCAL_CMDGCTL, 0x7FFF);
+
+	b43_phy_mask(dev, B43_PHY_HT_SAMP_CMD, ~0x0004);
+
+	for (i = 0; i < 3; i++) {
+		if (phy_ht->bb_mult_save[i] >= 0) {
+			b43_httab_write(dev, B43_HTTAB16(13, 0x63 + i * 4),
+					phy_ht->bb_mult_save[i]);
+			b43_httab_write(dev, B43_HTTAB16(13, 0x67 + i * 4),
+					phy_ht->bb_mult_save[i]);
+		}
+	}
+}
+#endif
+
+/**************************************************
  * Tx/Rx
  **************************************************/
 
@@ -357,6 +387,13 @@ static void b43_phy_ht_tx_power_ctl(struct b43_wldev *dev, bool enable)
 
 	phy_ht->tx_pwr_ctl = enable;
 }
+
+static void b43_phy_ht_tx_power_ctl_idle_tssi(struct b43_wldev *dev)
+{
+	/* TODO */
+	b43_phy_ht_stop_playback(dev);
+	/* TODO */
+}
 #endif
 
 /**************************************************
@@ -502,6 +539,9 @@ static void b43_phy_ht_op_prepare_structs(struct b43_wldev *dev)
 	phy_ht->tx_pwr_ctl = true;
 	for (i = 0; i < 3; i++)
 		phy_ht->tx_pwr_idx[i] = B43_PHY_HT_TXPCTL_CMD_C1_INIT + 1;
+
+	for (i = 0; i < 3; i++)
+		phy_ht->bb_mult_save[i] = -1;
 }
 
 static int b43_phy_ht_op_init(struct b43_wldev *dev)
@@ -640,6 +680,7 @@ static int b43_phy_ht_op_init(struct b43_wldev *dev)
 	b43_phy_ht_tx_power_fix(dev);
 #if 0
 	b43_phy_ht_tx_power_ctl(dev, false);
+	b43_phy_ht_tx_power_ctl_idle_tssi(dev);
 	/* TODO */
 	b43_phy_ht_tx_power_ctl(dev, saved_tx_pwr_ctl);
 #endif
drivers/net/wireless/b43/phy_ht.h +6 -0
index bc7a43f..7ec794b 100644
@@ -16,6 +16,10 @@
 #define  B43_PHY_HT_CLASS_CTL_CCK_EN		0x0001 /* CCK enable */
 #define  B43_PHY_HT_CLASS_CTL_OFDM_EN		0x0002 /* OFDM enable */
 #define  B43_PHY_HT_CLASS_CTL_WAITED_EN		0x0004 /* Waited enable */
+#define B43_PHY_HT_IQLOCAL_CMDGCTL		0x0C2	/* I/Q LO cal command G control */
+#define B43_PHY_HT_SAMP_CMD			0x0C3	/* Sample command */
+#define  B43_PHY_HT_SAMP_CMD_STOP		0x0002	/* Stop */
+#define B43_PHY_HT_SAMP_STAT			0x0C7	/* Sample status */
 #define B43_PHY_HT_BW1				0x1CE
 #define B43_PHY_HT_BW2				0x1CF
 #define B43_PHY_HT_BW3				0x1D0
@@ -80,6 +84,8 @@ struct b43_phy_ht {
 
 	bool tx_pwr_ctl;
 	u8 tx_pwr_idx[3];
+
+	s32 bb_mult_save[3];
 };
 
 
Signature · 1 line
1.7.10.4
#13 lore raw

PATCH 10/13 b43: HT-PHY: implement playing sample tone

In reply to Rafał Miłecki
---
 drivers/net/wireless/b43/phy_ht.c |   69 +++++++++++++++++++++++++++++++++++++
 drivers/net/wireless/b43/phy_ht.h |    5 +++
 2 files changed, 74 insertions(+)
drivers/net/wireless/b43/phy_ht.c +69 -0
index 8e5d5bd..363c64c 100644
@@ -321,6 +321,70 @@ static void b43_phy_ht_stop_playback(struct b43_wldev *dev)
 		}
 	}
 }
+
+static u16 b43_phy_ht_load_samples(struct b43_wldev *dev)
+{
+	int i;
+	u16 len = 20 << 3;
+
+	b43_phy_write(dev, B43_PHY_HT_TABLE_ADDR, 0x4400);
+
+	for (i = 0; i < len; i++) {
+		b43_phy_write(dev, B43_PHY_HT_TABLE_DATAHI, 0);
+		b43_phy_write(dev, B43_PHY_HT_TABLE_DATALO, 0);
+	}
+
+	return len;
+}
+
+static void b43_phy_ht_run_samples(struct b43_wldev *dev, u16 samps, u16 loops,
+				   u16 wait)
+{
+	struct b43_phy_ht *phy_ht = dev->phy.ht;
+	u16 save_seq_mode;
+	int i;
+
+	for (i = 0; i < 3; i++) {
+		if (phy_ht->bb_mult_save[i] < 0)
+			phy_ht->bb_mult_save[i] = b43_httab_read(dev, B43_HTTAB16(13, 0x63 + i * 4));
+	}
+
+	b43_phy_write(dev, B43_PHY_HT_SAMP_DEP_CNT, samps - 1);
+	if (loops != 0xFFFF)
+		loops--;
+	b43_phy_write(dev, B43_PHY_HT_SAMP_LOOP_CNT, loops);
+	b43_phy_write(dev, B43_PHY_HT_SAMP_WAIT_CNT, wait);
+
+	save_seq_mode = b43_phy_read(dev, B43_PHY_HT_RF_SEQ_MODE);
+	b43_phy_set(dev, B43_PHY_HT_RF_SEQ_MODE,
+		    B43_PHY_HT_RF_SEQ_MODE_CA_OVER);
+
+	/* TODO: find out mask bits! Do we need more function arguments? */
+	b43_phy_mask(dev, B43_PHY_HT_SAMP_CMD, ~0);
+	b43_phy_mask(dev, B43_PHY_HT_SAMP_CMD, ~0);
+	b43_phy_mask(dev, B43_PHY_HT_IQLOCAL_CMDGCTL, ~0);
+	b43_phy_set(dev, B43_PHY_HT_SAMP_CMD, 0x1);
+
+	for (i = 0; i < 100; i++) {
+		if (!(b43_phy_read(dev, B43_PHY_HT_RF_SEQ_STATUS) & 1)) {
+			i = 0;
+			break;
+		}
+		udelay(10);
+	}
+	if (i)
+		b43err(dev->wl, "run samples timeout\n");
+
+	b43_phy_write(dev, B43_PHY_HT_RF_SEQ_MODE, save_seq_mode);
+}
+
+static void b43_phy_ht_tx_tone(struct b43_wldev *dev)
+{
+	u16 samp;
+
+	samp = b43_phy_ht_load_samples(dev);
+	b43_phy_ht_run_samples(dev, samp, 0xFFFF, 0);
+}
 #endif
 
 /**************************************************
@@ -391,7 +455,12 @@ static void b43_phy_ht_tx_power_ctl(struct b43_wldev *dev, bool enable)
 static void b43_phy_ht_tx_power_ctl_idle_tssi(struct b43_wldev *dev)
 {
 	/* TODO */
+
+	b43_phy_ht_tx_tone(dev);
+	udelay(20);
+	/* TODO: poll RSSI */
 	b43_phy_ht_stop_playback(dev);
+
 	/* TODO */
 }
 #endif
drivers/net/wireless/b43/phy_ht.h +5 -0
index 7ec794b..c517958 100644
@@ -19,6 +19,9 @@
 #define B43_PHY_HT_IQLOCAL_CMDGCTL		0x0C2	/* I/Q LO cal command G control */
 #define B43_PHY_HT_SAMP_CMD			0x0C3	/* Sample command */
 #define  B43_PHY_HT_SAMP_CMD_STOP		0x0002	/* Stop */
+#define B43_PHY_HT_SAMP_LOOP_CNT		0x0C4	/* Sample loop count */
+#define B43_PHY_HT_SAMP_WAIT_CNT		0x0C5	/* Sample wait count */
+#define B43_PHY_HT_SAMP_DEP_CNT			0x0C6	/* Sample depth count */
 #define B43_PHY_HT_SAMP_STAT			0x0C7	/* Sample status */
 #define B43_PHY_HT_BW1				0x1CE
 #define B43_PHY_HT_BW2				0x1CF
@@ -39,6 +42,8 @@
 #define B43_PHY_HT_C3_CLIP1THRES		B43_PHY_OFDM(0x08E)
 
 #define B43_PHY_HT_RF_SEQ_MODE			B43_PHY_EXTG(0x000)
+#define  B43_PHY_HT_RF_SEQ_MODE_CA_OVER		0x0001	/* Core active override */
+#define  B43_PHY_HT_RF_SEQ_MODE_TR_OVER		0x0002	/* Trigger override */
 #define B43_PHY_HT_RF_SEQ_TRIG			B43_PHY_EXTG(0x003)
 #define  B43_PHY_HT_RF_SEQ_TRIG_RX2TX		0x0001 /* RX2TX */
 #define  B43_PHY_HT_RF_SEQ_TRIG_TX2RX		0x0002 /* TX2RX */
Signature · 1 line
1.7.10.4
#14 lore raw

PATCH 11/13 b43: HT-PHY: implement RSSI polling

In reply to Rafał Miłecki
---
 drivers/net/wireless/b43/phy_ht.c |   96 ++++++++++++++++++++++++++++++++++++-
 drivers/net/wireless/b43/phy_ht.h |    5 ++
 2 files changed, 100 insertions(+), 1 deletion(-)
drivers/net/wireless/b43/phy_ht.c +95 -1
index 363c64c..831dca4 100644
@@ -388,6 +388,92 @@ static void b43_phy_ht_tx_tone(struct b43_wldev *dev)
 #endif
 
 /**************************************************
+ * RSSI
+ **************************************************/
+
+#if 0
+static void b43_phy_ht_rssi_select(struct b43_wldev *dev, u8 core_sel,
+				   u8 rssi_type)
+{
+	const u16 ctl_regs[3][2] = {
+		{ B43_PHY_HT_AFE_C1, B43_PHY_HT_AFE_C1_OVER, },
+		{ B43_PHY_HT_AFE_C2, B43_PHY_HT_AFE_C2_OVER, },
+		{ B43_PHY_HT_AFE_C3, B43_PHY_HT_AFE_C3_OVER, },
+	};
+	const u16 radio_r[] = { R2059_SYN, R2059_TXRX0, R2059_RXRX1, };
+	int core;
+
+	if (core_sel == 0) {
+		b43err(dev->wl, "RSSI selection for core off not implemented yet\n");
+	} else {
+		for (core = 0; core < 3; core++) {
+			/* Check if caller requested a one specific core */
+			if ((core_sel == 1 && core != 0) ||
+			    (core_sel == 2 && core != 1) ||
+			    (core_sel == 3 && core != 2))
+				continue;
+
+			switch (rssi_type) {
+			case 4:
+				b43_phy_set(dev, ctl_regs[core][0], 0x3 << 8);
+				b43_phy_set(dev, ctl_regs[core][0], 0x3 << 10);
+				b43_phy_set(dev, ctl_regs[core][1], 0x1 << 9);
+				b43_phy_set(dev, ctl_regs[core][1], 0x1 << 10);
+
+				b43_radio_set(dev, R2059_RXRX1 | 0xbf, 0x1);
+				b43_radio_write(dev, radio_r[core] | 0x159,
+						0x11);
+				break;
+			default:
+				b43err(dev->wl, "RSSI selection for type %d not implemented yet\n",
+				       rssi_type);
+			}
+		}
+	}
+}
+
+static void b43_phy_ht_poll_rssi(struct b43_wldev *dev, u8 type, s32 *buf,
+				 u8 nsamp)
+{
+	u16 phy_regs_values[12];
+	u16 phy_regs_to_save[] = {
+		B43_PHY_HT_AFE_C1, B43_PHY_HT_AFE_C1_OVER,
+		0x848, 0x841,
+		B43_PHY_HT_AFE_C2, B43_PHY_HT_AFE_C2_OVER,
+		0x868, 0x861,
+		B43_PHY_HT_AFE_C3, B43_PHY_HT_AFE_C3_OVER,
+		0x888, 0x881,
+	};
+	u16 tmp[3];
+	int i;
+
+	for (i = 0; i < 12; i++)
+		phy_regs_values[i] = b43_phy_read(dev, phy_regs_to_save[i]);
+
+	b43_phy_ht_rssi_select(dev, 5, type);
+
+	for (i = 0; i < 6; i++)
+		buf[i] = 0;
+
+	for (i = 0; i < nsamp; i++) {
+		tmp[0] = b43_phy_read(dev, B43_PHY_HT_RSSI_C1);
+		tmp[1] = b43_phy_read(dev, B43_PHY_HT_RSSI_C2);
+		tmp[2] = b43_phy_read(dev, B43_PHY_HT_RSSI_C3);
+
+		buf[0] += ((s8)((tmp[0] & 0x3F) << 2)) >> 2;
+		buf[1] += ((s8)(((tmp[0] >> 8) & 0x3F) << 2)) >> 2;
+		buf[2] += ((s8)((tmp[1] & 0x3F) << 2)) >> 2;
+		buf[3] += ((s8)(((tmp[1] >> 8) & 0x3F) << 2)) >> 2;
+		buf[4] += ((s8)((tmp[2] & 0x3F) << 2)) >> 2;
+		buf[5] += ((s8)(((tmp[2] >> 8) & 0x3F) << 2)) >> 2;
+	}
+
+	for (i = 0; i < 12; i++)
+		b43_phy_write(dev, phy_regs_to_save[i], phy_regs_values[i]);
+}
+#endif
+
+/**************************************************
  * Tx/Rx
  **************************************************/
 
@@ -454,12 +540,20 @@ static void b43_phy_ht_tx_power_ctl(struct b43_wldev *dev, bool enable)
 
 static void b43_phy_ht_tx_power_ctl_idle_tssi(struct b43_wldev *dev)
 {
+	struct b43_phy_ht *phy_ht = dev->phy.ht;
+	s32 rssi_buf[6];
+
 	/* TODO */
 
 	b43_phy_ht_tx_tone(dev);
 	udelay(20);
-	/* TODO: poll RSSI */
+	b43_phy_ht_poll_rssi(dev, 4, rssi_buf, 1);
 	b43_phy_ht_stop_playback(dev);
+	b43_phy_ht_reset_cca(dev);
+
+	phy_ht->idle_tssi[0] = rssi_buf[0] & 0xff;
+	phy_ht->idle_tssi[1] = rssi_buf[2] & 0xff;
+	phy_ht->idle_tssi[2] = rssi_buf[4] & 0xff;
 
 	/* TODO */
 }
drivers/net/wireless/b43/phy_ht.h +5 -0
index c517958..165c501 100644
@@ -36,6 +36,9 @@
 #define  B43_PHY_HT_TXPCTL_CMD_C1_PCTLEN	0x8000	/* TX power control enable */
 #define B43_PHY_HT_TXPCTL_CMD_C2		0x222
 #define  B43_PHY_HT_TXPCTL_CMD_C2_INIT		0x007F
+#define B43_PHY_HT_RSSI_C1			0x219
+#define B43_PHY_HT_RSSI_C2			0x21A
+#define B43_PHY_HT_RSSI_C3			0x21B
 
 #define B43_PHY_HT_C1_CLIP1THRES		B43_PHY_OFDM(0x00E)
 #define B43_PHY_HT_C2_CLIP1THRES		B43_PHY_OFDM(0x04E)
@@ -91,6 +94,8 @@ struct b43_phy_ht {
 	u8 tx_pwr_idx[3];
 
 	s32 bb_mult_save[3];
+
+	u8 idle_tssi[3];
 };
 
 
Signature · 1 line
1.7.10.4
#15 lore raw

PATCH 11/13 b43: HT-PHY: implement RSSI polling

Quoted 5 lines · On Thu, 7 Mar 2013 16:47:25 +0100 Rafa? Mi?ecki <[email protected]> wrote:
drivers/net/wireless/b43/phy_ht.c +5 -0
+	const u16 ctl_regs[3][2] = {
+		{ B43_PHY_HT_AFE_C1, B43_PHY_HT_AFE_C1_OVER, },
+		{ B43_PHY_HT_AFE_C2, B43_PHY_HT_AFE_C2_OVER, },
+		{ B43_PHY_HT_AFE_C3, B43_PHY_HT_AFE_C3_OVER, },
+	};

drivers/net/wireless/b43/phy_ht.c static void b43_phy_ht_tx_tone(struct b43_wldev *dev) · line 446

Quoted 10 lines
drivers/net/wireless/b43/phy_ht.c +9 -0
+	const u16 radio_r[] = { R2059_SYN, R2059_TXRX0, R2059_RXRX1, };
 
+	u16 phy_regs_to_save[] = {
+		B43_PHY_HT_AFE_C1, B43_PHY_HT_AFE_C1_OVER,
+		0x848, 0x841,
+		B43_PHY_HT_AFE_C2, B43_PHY_HT_AFE_C2_OVER,
+		0x868, 0x861,
+		B43_PHY_HT_AFE_C3, B43_PHY_HT_AFE_C3_OVER,
+		0x888, 0x881,
+	};

It usually is better to define tables that are constant as "static const", so that they are not put on the kernel stack.

Signature · 8 lines
Michael
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 836 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/b43-dev/attachments/20130307/b57a29aa/attachment.sig>
#16 lore raw

PATCH 11/13 b43: HT-PHY: implement RSSI polling

2013/3/7 Michael B?sch <[email protected]>:

Quoted 19 lines
Quoted 5 lines · On Thu, 7 Mar 2013 16:47:25 +0100 Rafa? Mi?ecki <[email protected]> wrote:
drivers/net/wireless/b43/phy_ht.c +5 -0
+     const u16 ctl_regs[3][2] = {
+             { B43_PHY_HT_AFE_C1, B43_PHY_HT_AFE_C1_OVER, },
+             { B43_PHY_HT_AFE_C2, B43_PHY_HT_AFE_C2_OVER, },
+             { B43_PHY_HT_AFE_C3, B43_PHY_HT_AFE_C3_OVER, },
+     };

drivers/net/wireless/b43/phy_ht.c static void b43_phy_ht_tx_tone(struct b43_wldev *dev) · line 446

Quoted 10 lines
drivers/net/wireless/b43/phy_ht.c +9 -0
+     const u16 radio_r[] = { R2059_SYN, R2059_TXRX0, R2059_RXRX1, };
 
+     u16 phy_regs_to_save[] = {
+             B43_PHY_HT_AFE_C1, B43_PHY_HT_AFE_C1_OVER,
+             0x848, 0x841,
+             B43_PHY_HT_AFE_C2, B43_PHY_HT_AFE_C2_OVER,
+             0x868, 0x861,
+             B43_PHY_HT_AFE_C3, B43_PHY_HT_AFE_C3_OVER,
+             0x888, 0x881,
+     };
Quoted 2 lines

It usually is better to define tables that are constant as "static const", so that they are not put on the kernel stack.

Thanks, I'll fix that, will just wait a little longer for more comments (if any appear)

Signature · 1 line
Rafa?
#17 lore raw

PATCH v2 1/13 b43: HT-PHY: rename AFE defines

In reply to Rafał Miłecki

It you take a look at N-PHY analog switch function it touches every core on the chipset. It seems HT-PHY does they same, it just has 3 cores instead of 2 (which make sense since BCM4331 is 3x3). Rename AFE defines to include core id.

---
V2: make ctl_regs array static btw

---
 drivers/net/wireless/b43/phy_ht.c |   38 ++++++++++++++++++-------------------
 drivers/net/wireless/b43/phy_ht.h |   12 ++++++------
 2 files changed, 25 insertions(+), 25 deletions(-)
drivers/net/wireless/b43/phy_ht.c +19 -19
index 3719a88..df07c83 100644
@@ -176,10 +176,10 @@ static void b43_phy_ht_afe_unk1(struct b43_wldev *dev)
 {
 	u8 i;
 
-	const u16 ctl_regs[3][2] = {
-		{ B43_PHY_HT_AFE_CTL1, B43_PHY_HT_AFE_CTL2 },
-		{ B43_PHY_HT_AFE_CTL3, B43_PHY_HT_AFE_CTL4 },
-		{ B43_PHY_HT_AFE_CTL5, B43_PHY_HT_AFE_CTL6},
+	static const u16 ctl_regs[3][2] = {
+		{ B43_PHY_HT_AFE_C1_OVER, B43_PHY_HT_AFE_C1 },
+		{ B43_PHY_HT_AFE_C2_OVER, B43_PHY_HT_AFE_C2 },
+		{ B43_PHY_HT_AFE_C3_OVER, B43_PHY_HT_AFE_C3},
 	};
 
 	for (i = 0; i < 3; i++) {
@@ -362,9 +362,9 @@ static int b43_phy_ht_op_init(struct b43_wldev *dev)
 
 	b43_phy_mask(dev, B43_PHY_EXTG(0), ~0x3);
 
-	b43_phy_write(dev, B43_PHY_HT_AFE_CTL1, 0);
-	b43_phy_write(dev, B43_PHY_HT_AFE_CTL3, 0);
-	b43_phy_write(dev, B43_PHY_HT_AFE_CTL5, 0);
+	b43_phy_write(dev, B43_PHY_HT_AFE_C1_OVER, 0);
+	b43_phy_write(dev, B43_PHY_HT_AFE_C2_OVER, 0);
+	b43_phy_write(dev, B43_PHY_HT_AFE_C3_OVER, 0);
 
 	b43_phy_write(dev, B43_PHY_EXTG(0x103), 0x20);
 	b43_phy_write(dev, B43_PHY_EXTG(0x101), 0x20);
@@ -511,19 +511,19 @@ static void b43_phy_ht_op_software_rfkill(struct b43_wldev *dev,
 static void b43_phy_ht_op_switch_analog(struct b43_wldev *dev, bool on)
 {
 	if (on) {
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL2, 0x00cd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL1, 0x0000);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL4, 0x00cd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL3, 0x0000);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL6, 0x00cd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL5, 0x0000);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C1, 0x00cd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C1_OVER, 0x0000);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C2, 0x00cd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C2_OVER, 0x0000);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C3, 0x00cd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C3_OVER, 0x0000);
 	} else {
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL1, 0x07ff);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL2, 0x00fd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL3, 0x07ff);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL4, 0x00fd);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL5, 0x07ff);
-		b43_phy_write(dev, B43_PHY_HT_AFE_CTL6, 0x00fd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C1_OVER, 0x07ff);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C1, 0x00fd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C2_OVER, 0x07ff);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C2, 0x00fd);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C3_OVER, 0x07ff);
+		b43_phy_write(dev, B43_PHY_HT_AFE_C3, 0x00fd);
 	}
 }
 
drivers/net/wireless/b43/phy_ht.h +6 -6
index 6544c42..60824fa 100644
@@ -36,12 +36,12 @@
 
 #define B43_PHY_HT_RF_CTL1			B43_PHY_EXTG(0x010)
 
-#define B43_PHY_HT_AFE_CTL1			B43_PHY_EXTG(0x110)
-#define B43_PHY_HT_AFE_CTL2			B43_PHY_EXTG(0x111)
-#define B43_PHY_HT_AFE_CTL3			B43_PHY_EXTG(0x114)
-#define B43_PHY_HT_AFE_CTL4			B43_PHY_EXTG(0x115)
-#define B43_PHY_HT_AFE_CTL5			B43_PHY_EXTG(0x118)
-#define B43_PHY_HT_AFE_CTL6			B43_PHY_EXTG(0x119)
+#define B43_PHY_HT_AFE_C1_OVER			B43_PHY_EXTG(0x110)
+#define B43_PHY_HT_AFE_C1			B43_PHY_EXTG(0x111)
+#define B43_PHY_HT_AFE_C2_OVER			B43_PHY_EXTG(0x114)
+#define B43_PHY_HT_AFE_C2			B43_PHY_EXTG(0x115)
+#define B43_PHY_HT_AFE_C3_OVER			B43_PHY_EXTG(0x118)
+#define B43_PHY_HT_AFE_C3			B43_PHY_EXTG(0x119)
 
 
 /* Values for PHY registers used on channel switching */
Signature · 1 line
1.7.10.4
#18 lore raw

PATCH v2 11/13 b43: HT-PHY: implement RSSI polling

In reply to Rafał Miłecki

---
V2: use static const where possible (for arrays)

---
 drivers/net/wireless/b43/phy_ht.c |   96 ++++++++++++++++++++++++++++++++++++-
 drivers/net/wireless/b43/phy_ht.h |    5 ++
 2 files changed, 100 insertions(+), 1 deletion(-)
drivers/net/wireless/b43/phy_ht.c +95 -1
index 22fdde6..ae9cd29 100644
@@ -388,6 +388,92 @@ static void b43_phy_ht_tx_tone(struct b43_wldev *dev)
 #endif
 
 /**************************************************
+ * RSSI
+ **************************************************/
+
+#if 0
+static void b43_phy_ht_rssi_select(struct b43_wldev *dev, u8 core_sel,
+				   u8 rssi_type)
+{
+	static const u16 ctl_regs[3][2] = {
+		{ B43_PHY_HT_AFE_C1, B43_PHY_HT_AFE_C1_OVER, },
+		{ B43_PHY_HT_AFE_C2, B43_PHY_HT_AFE_C2_OVER, },
+		{ B43_PHY_HT_AFE_C3, B43_PHY_HT_AFE_C3_OVER, },
+	};
+	static const u16 radio_r[] = { R2059_SYN, R2059_TXRX0, R2059_RXRX1, };
+	int core;
+
+	if (core_sel == 0) {
+		b43err(dev->wl, "RSSI selection for core off not implemented yet\n");
+	} else {
+		for (core = 0; core < 3; core++) {
+			/* Check if caller requested a one specific core */
+			if ((core_sel == 1 && core != 0) ||
+			    (core_sel == 2 && core != 1) ||
+			    (core_sel == 3 && core != 2))
+				continue;
+
+			switch (rssi_type) {
+			case 4:
+				b43_phy_set(dev, ctl_regs[core][0], 0x3 << 8);
+				b43_phy_set(dev, ctl_regs[core][0], 0x3 << 10);
+				b43_phy_set(dev, ctl_regs[core][1], 0x1 << 9);
+				b43_phy_set(dev, ctl_regs[core][1], 0x1 << 10);
+
+				b43_radio_set(dev, R2059_RXRX1 | 0xbf, 0x1);
+				b43_radio_write(dev, radio_r[core] | 0x159,
+						0x11);
+				break;
+			default:
+				b43err(dev->wl, "RSSI selection for type %d not implemented yet\n",
+				       rssi_type);
+			}
+		}
+	}
+}
+
+static void b43_phy_ht_poll_rssi(struct b43_wldev *dev, u8 type, s32 *buf,
+				 u8 nsamp)
+{
+	u16 phy_regs_values[12];
+	static const u16 phy_regs_to_save[] = {
+		B43_PHY_HT_AFE_C1, B43_PHY_HT_AFE_C1_OVER,
+		0x848, 0x841,
+		B43_PHY_HT_AFE_C2, B43_PHY_HT_AFE_C2_OVER,
+		0x868, 0x861,
+		B43_PHY_HT_AFE_C3, B43_PHY_HT_AFE_C3_OVER,
+		0x888, 0x881,
+	};
+	u16 tmp[3];
+	int i;
+
+	for (i = 0; i < 12; i++)
+		phy_regs_values[i] = b43_phy_read(dev, phy_regs_to_save[i]);
+
+	b43_phy_ht_rssi_select(dev, 5, type);
+
+	for (i = 0; i < 6; i++)
+		buf[i] = 0;
+
+	for (i = 0; i < nsamp; i++) {
+		tmp[0] = b43_phy_read(dev, B43_PHY_HT_RSSI_C1);
+		tmp[1] = b43_phy_read(dev, B43_PHY_HT_RSSI_C2);
+		tmp[2] = b43_phy_read(dev, B43_PHY_HT_RSSI_C3);
+
+		buf[0] += ((s8)((tmp[0] & 0x3F) << 2)) >> 2;
+		buf[1] += ((s8)(((tmp[0] >> 8) & 0x3F) << 2)) >> 2;
+		buf[2] += ((s8)((tmp[1] & 0x3F) << 2)) >> 2;
+		buf[3] += ((s8)(((tmp[1] >> 8) & 0x3F) << 2)) >> 2;
+		buf[4] += ((s8)((tmp[2] & 0x3F) << 2)) >> 2;
+		buf[5] += ((s8)(((tmp[2] >> 8) & 0x3F) << 2)) >> 2;
+	}
+
+	for (i = 0; i < 12; i++)
+		b43_phy_write(dev, phy_regs_to_save[i], phy_regs_values[i]);
+}
+#endif
+
+/**************************************************
  * Tx/Rx
  **************************************************/
 
@@ -454,12 +540,20 @@ static void b43_phy_ht_tx_power_ctl(struct b43_wldev *dev, bool enable)
 
 static void b43_phy_ht_tx_power_ctl_idle_tssi(struct b43_wldev *dev)
 {
+	struct b43_phy_ht *phy_ht = dev->phy.ht;
+	s32 rssi_buf[6];
+
 	/* TODO */
 
 	b43_phy_ht_tx_tone(dev);
 	udelay(20);
-	/* TODO: poll RSSI */
+	b43_phy_ht_poll_rssi(dev, 4, rssi_buf, 1);
 	b43_phy_ht_stop_playback(dev);
+	b43_phy_ht_reset_cca(dev);
+
+	phy_ht->idle_tssi[0] = rssi_buf[0] & 0xff;
+	phy_ht->idle_tssi[1] = rssi_buf[2] & 0xff;
+	phy_ht->idle_tssi[2] = rssi_buf[4] & 0xff;
 
 	/* TODO */
 }
drivers/net/wireless/b43/phy_ht.h +5 -0
index c517958..165c501 100644
@@ -36,6 +36,9 @@
 #define  B43_PHY_HT_TXPCTL_CMD_C1_PCTLEN	0x8000	/* TX power control enable */
 #define B43_PHY_HT_TXPCTL_CMD_C2		0x222
 #define  B43_PHY_HT_TXPCTL_CMD_C2_INIT		0x007F
+#define B43_PHY_HT_RSSI_C1			0x219
+#define B43_PHY_HT_RSSI_C2			0x21A
+#define B43_PHY_HT_RSSI_C3			0x21B
 
 #define B43_PHY_HT_C1_CLIP1THRES		B43_PHY_OFDM(0x00E)
 #define B43_PHY_HT_C2_CLIP1THRES		B43_PHY_OFDM(0x04E)
@@ -91,6 +94,8 @@ struct b43_phy_ht {
 	u8 tx_pwr_idx[3];
 
 	s32 bb_mult_save[3];
+
+	u8 idle_tssi[3];
 };
 
 
Signature · 1 line
1.7.10.4
#19 lore raw

PATCH 12/13 b43: HT-PHY: setup TX power control

In reply to Rafał Miłecki
---
 drivers/net/wireless/b43/phy_ht.c |  109 +++++++++++++++++++++++++++++++++++++
 drivers/net/wireless/b43/phy_ht.h |   25 +++++++++
 2 files changed, 134 insertions(+)
drivers/net/wireless/b43/phy_ht.c +109 -0
index 831dca4..6d5eb04 100644
@@ -557,6 +557,114 @@ static void b43_phy_ht_tx_power_ctl_idle_tssi(struct b43_wldev *dev)
 
 	/* TODO */
 }
+
+static void b43_phy_ht_tx_power_ctl_setup(struct b43_wldev *dev)
+{
+	struct b43_phy_ht *phy_ht = dev->phy.ht;
+	struct ssb_sprom *sprom = dev->dev->bus_sprom;
+
+	u8 *idle = phy_ht->idle_tssi;
+	u8 target[3];
+	s16 a1[3], b0[3], b1[3];
+
+	u16 freq = dev->phy.channel_freq;
+	int i, c;
+
+	if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ) {
+		for (c = 0; c < 3; c++) {
+			target[c] = sprom->core_pwr_info[c].maxpwr_2g;
+			a1[c] = sprom->core_pwr_info[c].pa_2g[0];
+			b0[c] = sprom->core_pwr_info[c].pa_2g[1];
+			b1[c] = sprom->core_pwr_info[c].pa_2g[2];
+		}
+	} else if (freq >= 4900 && freq < 5100) {
+		for (c = 0; c < 3; c++) {
+			target[c] = sprom->core_pwr_info[c].maxpwr_5gl;
+			a1[c] = sprom->core_pwr_info[c].pa_5gl[0];
+			b0[c] = sprom->core_pwr_info[c].pa_5gl[1];
+			b1[c] = sprom->core_pwr_info[c].pa_5gl[2];
+		}
+	} else if (freq >= 5100 && freq < 5500) {
+		for (c = 0; c < 3; c++) {
+			target[c] = sprom->core_pwr_info[c].maxpwr_5g;
+			a1[c] = sprom->core_pwr_info[c].pa_5g[0];
+			b0[c] = sprom->core_pwr_info[c].pa_5g[1];
+			b1[c] = sprom->core_pwr_info[c].pa_5g[2];
+		}
+	} else if (freq >= 5500) {
+		for (c = 0; c < 3; c++) {
+			target[c] = sprom->core_pwr_info[c].maxpwr_5gh;
+			a1[c] = sprom->core_pwr_info[c].pa_5gh[0];
+			b0[c] = sprom->core_pwr_info[c].pa_5gh[1];
+			b1[c] = sprom->core_pwr_info[c].pa_5gh[2];
+		}
+	} else {
+		target[0] = target[1] = target[2] = 52;
+		a1[0] = a1[1] = a1[2] = -424;
+		b0[0] = b0[1] = b0[2] = 5612;
+		b1[0] = b1[1] = b1[2] = -1393;
+	}
+
+	b43_phy_set(dev, B43_PHY_HT_TSSIMODE, B43_PHY_HT_TSSIMODE_EN);
+	b43_phy_mask(dev, B43_PHY_HT_TXPCTL_CMD_C1,
+		     ~B43_PHY_HT_TXPCTL_CMD_C1_PCTLEN & 0xFFFF);
+
+	/* TODO: Does it depend on sprom->fem.ghz2.tssipos? */
+	b43_phy_set(dev, B43_PHY_HT_TXPCTL_IDLE_TSSI, 0x4000);
+
+	b43_phy_maskset(dev, B43_PHY_HT_TXPCTL_CMD_C1,
+			~B43_PHY_HT_TXPCTL_CMD_C1_INIT, 0x19);
+	b43_phy_maskset(dev, B43_PHY_HT_TXPCTL_CMD_C2,
+			~B43_PHY_HT_TXPCTL_CMD_C2_INIT, 0x19);
+	b43_phy_maskset(dev, B43_PHY_HT_TXPCTL_CMD_C3,
+			~B43_PHY_HT_TXPCTL_CMD_C3_INIT, 0x19);
+
+	b43_phy_set(dev, B43_PHY_HT_TXPCTL_IDLE_TSSI,
+		    B43_PHY_HT_TXPCTL_IDLE_TSSI_BINF);
+
+	b43_phy_maskset(dev, B43_PHY_HT_TXPCTL_IDLE_TSSI,
+			~B43_PHY_HT_TXPCTL_IDLE_TSSI_C1,
+			idle[0] << B43_PHY_HT_TXPCTL_IDLE_TSSI_C1_SHIFT);
+	b43_phy_maskset(dev, B43_PHY_HT_TXPCTL_IDLE_TSSI,
+			~B43_PHY_HT_TXPCTL_IDLE_TSSI_C2,
+			idle[1] << B43_PHY_HT_TXPCTL_IDLE_TSSI_C2_SHIFT);
+	b43_phy_maskset(dev, B43_PHY_HT_TXPCTL_IDLE_TSSI2,
+			~B43_PHY_HT_TXPCTL_IDLE_TSSI2_C3,
+			idle[2] << B43_PHY_HT_TXPCTL_IDLE_TSSI2_C3_SHIFT);
+
+	b43_phy_maskset(dev, B43_PHY_HT_TXPCTL_N, ~B43_PHY_HT_TXPCTL_N_TSSID,
+			0xf0);
+	b43_phy_maskset(dev, B43_PHY_HT_TXPCTL_N, ~B43_PHY_HT_TXPCTL_N_NPTIL2,
+			0x3 << B43_PHY_HT_TXPCTL_N_NPTIL2_SHIFT);
+#if 0
+	/* TODO: what to mask/set? */
+	b43_phy_maskset(dev, B43_PHY_HT_TXPCTL_CMD_C1, 0x800, 0)
+	b43_phy_maskset(dev, B43_PHY_HT_TXPCTL_CMD_C1, 0x400, 0)
+#endif
+
+	b43_phy_maskset(dev, B43_PHY_HT_TXPCTL_TARG_PWR,
+			~B43_PHY_HT_TXPCTL_TARG_PWR_C1,
+			target[0] << B43_PHY_HT_TXPCTL_TARG_PWR_C1_SHIFT);
+	b43_phy_maskset(dev, B43_PHY_HT_TXPCTL_TARG_PWR,
+			~B43_PHY_HT_TXPCTL_TARG_PWR_C2 & 0xFFFF,
+			target[1] << B43_PHY_HT_TXPCTL_TARG_PWR_C2_SHIFT);
+	b43_phy_maskset(dev, B43_PHY_HT_TXPCTL_TARG_PWR2,
+			~B43_PHY_HT_TXPCTL_TARG_PWR2_C3,
+			target[2] << B43_PHY_HT_TXPCTL_TARG_PWR2_C3_SHIFT);
+
+	for (c = 0; c < 3; c++) {
+		s32 num, den, pwr;
+		u32 regval[64];
+
+		for (i = 0; i < 64; i++) {
+			num = 8 * (16 * b0[c] + b1[c] * i);
+			den = 32768 + a1[c] * i;
+			pwr = max((4 * num + den / 2) / den, -8);
+			regval[i] = pwr;
+		}
+		b43_httab_write_bulk(dev, B43_HTTAB16(26 + c, 0), 64, regval);
+	}
+}
 #endif
 
 /**************************************************
@@ -844,6 +952,7 @@ static int b43_phy_ht_op_init(struct b43_wldev *dev)
 #if 0
 	b43_phy_ht_tx_power_ctl(dev, false);
 	b43_phy_ht_tx_power_ctl_idle_tssi(dev);
+	b43_phy_ht_tx_power_ctl_setup(dev);
 	/* TODO */
 	b43_phy_ht_tx_power_ctl(dev, saved_tx_pwr_ctl);
 #endif
drivers/net/wireless/b43/phy_ht.h +25 -0
index 165c501..9b2408e 100644
@@ -23,6 +23,9 @@
 #define B43_PHY_HT_SAMP_WAIT_CNT		0x0C5	/* Sample wait count */
 #define B43_PHY_HT_SAMP_DEP_CNT			0x0C6	/* Sample depth count */
 #define B43_PHY_HT_SAMP_STAT			0x0C7	/* Sample status */
+#define B43_PHY_HT_TSSIMODE			0x122	/* TSSI mode */
+#define  B43_PHY_HT_TSSIMODE_EN			0x0001	/* TSSI enable */
+#define  B43_PHY_HT_TSSIMODE_PDEN		0x0002	/* Power det enable */
 #define B43_PHY_HT_BW1				0x1CE
 #define B43_PHY_HT_BW2				0x1CF
 #define B43_PHY_HT_BW3				0x1D0
@@ -34,6 +37,22 @@
 #define  B43_PHY_HT_TXPCTL_CMD_C1_COEFF		0x2000	/* Power control coefficients */
 #define  B43_PHY_HT_TXPCTL_CMD_C1_HWPCTLEN	0x4000	/* Hardware TX power control enable */
 #define  B43_PHY_HT_TXPCTL_CMD_C1_PCTLEN	0x8000	/* TX power control enable */
+#define B43_PHY_HT_TXPCTL_N			0x1E8	/* TX power control N num */
+#define  B43_PHY_HT_TXPCTL_N_TSSID		0x00FF	/* N TSSI delay */
+#define  B43_PHY_HT_TXPCTL_N_TSSID_SHIFT	0
+#define  B43_PHY_HT_TXPCTL_N_NPTIL2		0x0700	/* N PT integer log2 */
+#define  B43_PHY_HT_TXPCTL_N_NPTIL2_SHIFT	8
+#define B43_PHY_HT_TXPCTL_IDLE_TSSI		0x1E9	/* TX power control idle TSSI */
+#define  B43_PHY_HT_TXPCTL_IDLE_TSSI_C1		0x003F
+#define  B43_PHY_HT_TXPCTL_IDLE_TSSI_C1_SHIFT	0
+#define  B43_PHY_HT_TXPCTL_IDLE_TSSI_C2		0x3F00
+#define  B43_PHY_HT_TXPCTL_IDLE_TSSI_C2_SHIFT	8
+#define  B43_PHY_HT_TXPCTL_IDLE_TSSI_BINF	0x8000	/* Raw TSSI offset bin format */
+#define B43_PHY_HT_TXPCTL_TARG_PWR		0x1EA	/* TX power control target power */
+#define  B43_PHY_HT_TXPCTL_TARG_PWR_C1		0x00FF	/* Power 0 */
+#define  B43_PHY_HT_TXPCTL_TARG_PWR_C1_SHIFT	0
+#define  B43_PHY_HT_TXPCTL_TARG_PWR_C2		0xFF00	/* Power 1 */
+#define  B43_PHY_HT_TXPCTL_TARG_PWR_C2_SHIFT	8
 #define B43_PHY_HT_TXPCTL_CMD_C2		0x222
 #define  B43_PHY_HT_TXPCTL_CMD_C2_INIT		0x007F
 #define B43_PHY_HT_RSSI_C1			0x219
@@ -72,6 +91,12 @@
 
 #define B43_PHY_HT_TXPCTL_CMD_C3		B43_PHY_EXTG(0x164)
 #define  B43_PHY_HT_TXPCTL_CMD_C3_INIT		0x007F
+#define B43_PHY_HT_TXPCTL_IDLE_TSSI2		B43_PHY_EXTG(0x165)	/* TX power control idle TSSI */
+#define  B43_PHY_HT_TXPCTL_IDLE_TSSI2_C3	0x003F
+#define  B43_PHY_HT_TXPCTL_IDLE_TSSI2_C3_SHIFT	0
+#define B43_PHY_HT_TXPCTL_TARG_PWR2		B43_PHY_EXTG(0x166)	/* TX power control target power */
+#define  B43_PHY_HT_TXPCTL_TARG_PWR2_C3		0x00FF
+#define  B43_PHY_HT_TXPCTL_TARG_PWR2_C3_SHIFT	0
 
 #define B43_PHY_HT_TEST				B43_PHY_N_BMODE(0x00A)
 
Signature · 1 line
1.7.10.4
#20 lore raw

PATCH 13/13 b43: HT-PHY: enable basic TX power setup

In reply to Rafał Miłecki
---
 drivers/net/wireless/b43/phy_ht.c |    9 ---------
 1 file changed, 9 deletions(-)
drivers/net/wireless/b43/phy_ht.c +0 -9
index 6d5eb04..54e5c85 100644
@@ -297,7 +297,6 @@ static void b43_phy_ht_bphy_init(struct b43_wldev *dev)
  * Samples
  **************************************************/
 
-#if 0
 static void b43_phy_ht_stop_playback(struct b43_wldev *dev)
 {
 	struct b43_phy_ht *phy_ht = dev->phy.ht;
@@ -385,13 +384,11 @@ static void b43_phy_ht_tx_tone(struct b43_wldev *dev)
 	samp = b43_phy_ht_load_samples(dev);
 	b43_phy_ht_run_samples(dev, samp, 0xFFFF, 0);
 }
-#endif
 
 /**************************************************
  * RSSI
  **************************************************/
 
-#if 0
 static void b43_phy_ht_rssi_select(struct b43_wldev *dev, u8 core_sel,
 				   u8 rssi_type)
 {
@@ -471,7 +468,6 @@ static void b43_phy_ht_poll_rssi(struct b43_wldev *dev, u8 type, s32 *buf,
 	for (i = 0; i < 12; i++)
 		b43_phy_write(dev, phy_regs_to_save[i], phy_regs_values[i]);
 }
-#endif
 
 /**************************************************
  * Tx/Rx
@@ -499,7 +495,6 @@ static void b43_phy_ht_tx_power_fix(struct b43_wldev *dev)
 	}
 }
 
-#if 0
 static void b43_phy_ht_tx_power_ctl(struct b43_wldev *dev, bool enable)
 {
 	struct b43_phy_ht *phy_ht = dev->phy.ht;
@@ -665,7 +660,6 @@ static void b43_phy_ht_tx_power_ctl_setup(struct b43_wldev *dev)
 		b43_httab_write_bulk(dev, B43_HTTAB16(26 + c, 0), 64, regval);
 	}
 }
-#endif
 
 /**************************************************
  * Channel switching ops.
@@ -949,13 +943,10 @@ static int b43_phy_ht_op_init(struct b43_wldev *dev)
 
 	saved_tx_pwr_ctl = phy_ht->tx_pwr_ctl;
 	b43_phy_ht_tx_power_fix(dev);
-#if 0
 	b43_phy_ht_tx_power_ctl(dev, false);
 	b43_phy_ht_tx_power_ctl_idle_tssi(dev);
 	b43_phy_ht_tx_power_ctl_setup(dev);
-	/* TODO */
 	b43_phy_ht_tx_power_ctl(dev, saved_tx_pwr_ctl);
-#endif
 
 	return 0;
 }
Signature · 1 line
1.7.10.4
#21 lore raw

cover b43: implement basic TX power mgmt

In reply to Rafał Miłecki
Quoted 24 lines · Rafa? Mi?ecki

After spotting a lot of N-PHY-similar functions in BCM4331 dump of MMIO ops - split into names parts I was able to finally improve HT-PHY code.

It now sets TX basically, I can finally talk with devices that are few meters away, not just few centimetres. It's a little patch bomb, sorry for that, but I wasn't sure if my code is correct until it was complete and started working.

Rafa? Mi?ecki (13):
b43: HT-PHY: rename AFE defines
b43: HT-PHY: add classifier control function
b43: HT-PHY: move TX fix to the separated function
b43: HT-PHY: implement spurious tone avoidance
b43: HT-PHY: implement MAC reclocking
b43: HT-PHY: implement CCA reset
b43: HT-PHY: implement PA override
b43: HT-PHY: implement controlling TX power control
b43: HT-PHY: implement stopping sample tone playback
b43: HT-PHY: implement playing sample tone
b43: HT-PHY: implement RSSI polling
b43: HT-PHY: setup TX power control
b43: HT-PHY: enable basic TX power setup

Quoted 3 lines
  drivers/net/wireless/b43/phy_ht.c |  603 +++++++++++++++++++++++++++++++++----
  drivers/net/wireless/b43/phy_ht.h |   77 ++++-
  2 files changed, 613 insertions(+), 67 deletions(-)

What tree is used for these patches? Numbers 1-7 applied with offsets, and some fuzz. Number 8 failed, and I quit trying there. I am using wireless-testing that was a fresh pull yesterday after John rebased it.

Larry

#22 lore raw

cover b43: implement basic TX power mgmt

2013/3/7 Larry Finger <[email protected]>:

Quoted 32 lines · Rafa? Mi?ecki
Quoted 25 lines

After spotting a lot of N-PHY-similar functions in BCM4331 dump of MMIO ops - split into names parts I was able to finally improve HT-PHY code.

It now sets TX basically, I can finally talk with devices that are few meters away, not just few centimetres. It's a little patch bomb, sorry for that, but I wasn't sure if my code is correct until it was complete and started working.

Rafa? Mi?ecki (13):
b43: HT-PHY: rename AFE defines
b43: HT-PHY: add classifier control function
b43: HT-PHY: move TX fix to the separated function
b43: HT-PHY: implement spurious tone avoidance
b43: HT-PHY: implement MAC reclocking
b43: HT-PHY: implement CCA reset
b43: HT-PHY: implement PA override
b43: HT-PHY: implement controlling TX power control
b43: HT-PHY: implement stopping sample tone playback
b43: HT-PHY: implement playing sample tone
b43: HT-PHY: implement RSSI polling
b43: HT-PHY: setup TX power control
b43: HT-PHY: enable basic TX power setup

Quoted 4 lines
  drivers/net/wireless/b43/phy_ht.c |  603
+++++++++++++++++++++++++++++++++----
  drivers/net/wireless/b43/phy_ht.h |   77 ++++-
  2 files changed, 613 insertions(+), 67 deletions(-)
Quoted 3 lines

What tree is used for these patches? Numbers 1-7 applied with offsets, and some fuzz. Number 8 failed, and I quit trying there. I am using wireless-testing that was a fresh pull yesterday after John rebased it.

Whoops? It should apply just fine on re-based wireless-testing. I think I've refreshed my tree today.

git log drivers/net/wireless/

commit 7f6231751ef492c38dbef61d14881bff6f1de165

Author: Rafa? Mi?ecki <[email protected]>
Date:   Sun Feb 24 17:41:56 2013 +0100

b43: HT-PHY: rename AFE defines

commit 7c2332b8061b7d4d7cd539ced1277e78d976f3da

Author: Rafa? Mi?ecki <[email protected]>
Date:   Mon Mar 4 16:39:10 2013 +0100

b43: HT-PHY: make it BCMA-only

So the newest b43 patch my patchset applies on top of is 7c2332b8061b7d4d7cd539ced1277e78d976f3da

Signature · 1 line
Rafa?
#23 lore raw

cover b43: implement basic TX power mgmt

In reply to Larry Finger

2013/3/7 Larry Finger <[email protected]>:

Quoted 32 lines · Rafa? Mi?ecki
Quoted 25 lines

After spotting a lot of N-PHY-similar functions in BCM4331 dump of MMIO ops - split into names parts I was able to finally improve HT-PHY code.

It now sets TX basically, I can finally talk with devices that are few meters away, not just few centimetres. It's a little patch bomb, sorry for that, but I wasn't sure if my code is correct until it was complete and started working.

Rafa? Mi?ecki (13):
b43: HT-PHY: rename AFE defines
b43: HT-PHY: add classifier control function
b43: HT-PHY: move TX fix to the separated function
b43: HT-PHY: implement spurious tone avoidance
b43: HT-PHY: implement MAC reclocking
b43: HT-PHY: implement CCA reset
b43: HT-PHY: implement PA override
b43: HT-PHY: implement controlling TX power control
b43: HT-PHY: implement stopping sample tone playback
b43: HT-PHY: implement playing sample tone
b43: HT-PHY: implement RSSI polling
b43: HT-PHY: setup TX power control
b43: HT-PHY: enable basic TX power setup

Quoted 4 lines
  drivers/net/wireless/b43/phy_ht.c |  603
+++++++++++++++++++++++++++++++++----
  drivers/net/wireless/b43/phy_ht.h |   77 ++++-
  2 files changed, 613 insertions(+), 67 deletions(-)
Quoted 3 lines

What tree is used for these patches? Numbers 1-7 applied with offsets, and some fuzz. Number 8 failed, and I quit trying there. I am using wireless-testing that was a fresh pull yesterday after John rebased it.

I've just checkouted origin/master again, to make sure everything is clean, and patches applied fine. Please make sure you're using latest wireless-testing like a
http://git.kernel.org/cgit/linux/kernel/git/linville/wireless-testing.git/commit/?id=12c18c7a3d8f20366424834b20be40f7f3a9e2c2

Signature · 1 line
Rafa?
#24 lore raw

cover b43: implement basic TX power mgmt

Quoted 33 lines · Rafa? Mi?ecki

2013/3/7 Larry Finger <[email protected]>:

Quoted 32 lines · Rafa? Mi?ecki
Quoted 29 lines

After spotting a lot of N-PHY-similar functions in BCM4331 dump of MMIO ops - split into names parts I was able to finally improve HT-PHY code.

It now sets TX basically, I can finally talk with devices that are few meters away, not just few centimetres. It's a little patch bomb, sorry for that, but I wasn't sure if my code is correct until it was complete and started working.

Rafa? Mi?ecki (13):
b43: HT-PHY: rename AFE defines
b43: HT-PHY: add classifier control function
b43: HT-PHY: move TX fix to the separated function
b43: HT-PHY: implement spurious tone avoidance
b43: HT-PHY: implement MAC reclocking
b43: HT-PHY: implement CCA reset
b43: HT-PHY: implement PA override
b43: HT-PHY: implement controlling TX power control
b43: HT-PHY: implement stopping sample tone playback
b43: HT-PHY: implement playing sample tone
b43: HT-PHY: implement RSSI polling
b43: HT-PHY: setup TX power control
b43: HT-PHY: enable basic TX power setup

   drivers/net/wireless/b43/phy_ht.c |  603
+++++++++++++++++++++++++++++++++----
   drivers/net/wireless/b43/phy_ht.h |   77 ++++-
   2 files changed, 613 insertions(+), 67 deletions(-)
Quoted 8 lines
Quoted 3 lines

What tree is used for these patches? Numbers 1-7 applied with offsets, and some fuzz. Number 8 failed, and I quit trying there. I am using wireless-testing that was a fresh pull yesterday after John rebased it.

I've just checkouted origin/master again, to make sure everything is clean, and patches applied fine. Please make sure you're using latest wireless-testing like a
http://git.kernel.org/cgit/linux/kernel/git/linville/wireless-testing.git/commit/?id=12c18c7a3d8f20366424834b20be40f7f3a9e2c2

That is the tree that I have. I will explore more.

Larry

#25 lore raw

cover b43: implement basic TX power mgmt

In reply to Larry Finger

2013/3/7 Larry Finger <[email protected]>:

Quoted 32 lines · Rafa? Mi?ecki
Quoted 25 lines

After spotting a lot of N-PHY-similar functions in BCM4331 dump of MMIO ops - split into names parts I was able to finally improve HT-PHY code.

It now sets TX basically, I can finally talk with devices that are few meters away, not just few centimetres. It's a little patch bomb, sorry for that, but I wasn't sure if my code is correct until it was complete and started working.

Rafa? Mi?ecki (13):
b43: HT-PHY: rename AFE defines
b43: HT-PHY: add classifier control function
b43: HT-PHY: move TX fix to the separated function
b43: HT-PHY: implement spurious tone avoidance
b43: HT-PHY: implement MAC reclocking
b43: HT-PHY: implement CCA reset
b43: HT-PHY: implement PA override
b43: HT-PHY: implement controlling TX power control
b43: HT-PHY: implement stopping sample tone playback
b43: HT-PHY: implement playing sample tone
b43: HT-PHY: implement RSSI polling
b43: HT-PHY: setup TX power control
b43: HT-PHY: enable basic TX power setup

Quoted 4 lines
  drivers/net/wireless/b43/phy_ht.c |  603
+++++++++++++++++++++++++++++++++----
  drivers/net/wireless/b43/phy_ht.h |   77 ++++-
  2 files changed, 613 insertions(+), 67 deletions(-)
Quoted 3 lines

What tree is used for these patches? Numbers 1-7 applied with offsets, and some fuzz. Number 8 failed, and I quit trying there. I am using wireless-testing that was a fresh pull yesterday after John rebased it.

Has anyone else tried to apply this patchset?

Signature · 1 line
Rafa?
#26 lore raw

cover b43: implement basic TX power mgmt

Quoted 33 lines · Rafa? Mi?ecki

2013/3/7 Larry Finger <[email protected]>:

Quoted 32 lines · Rafa? Mi?ecki
Quoted 29 lines

After spotting a lot of N-PHY-similar functions in BCM4331 dump of MMIO ops - split into names parts I was able to finally improve HT-PHY code.

It now sets TX basically, I can finally talk with devices that are few meters away, not just few centimetres. It's a little patch bomb, sorry for that, but I wasn't sure if my code is correct until it was complete and started working.

Rafa? Mi?ecki (13):
b43: HT-PHY: rename AFE defines
b43: HT-PHY: add classifier control function
b43: HT-PHY: move TX fix to the separated function
b43: HT-PHY: implement spurious tone avoidance
b43: HT-PHY: implement MAC reclocking
b43: HT-PHY: implement CCA reset
b43: HT-PHY: implement PA override
b43: HT-PHY: implement controlling TX power control
b43: HT-PHY: implement stopping sample tone playback
b43: HT-PHY: implement playing sample tone
b43: HT-PHY: implement RSSI polling
b43: HT-PHY: setup TX power control
b43: HT-PHY: enable basic TX power setup

  drivers/net/wireless/b43/phy_ht.c |  603
+++++++++++++++++++++++++++++++++----
  drivers/net/wireless/b43/phy_ht.h |   77 ++++-
  2 files changed, 613 insertions(+), 67 deletions(-)
Quoted 6 lines
Quoted 3 lines

What tree is used for these patches? Numbers 1-7 applied with offsets, and some fuzz. Number 8 failed, and I quit trying there. I am using wireless-testing that was a fresh pull yesterday after John rebased it.

Has anyone else tried to apply this patchset?

I just applied them on wireless-testing/master without any problems, last commit was 14c8aaa01066072600b13b9825c571e4ecf7c0e9 I haven't seen any fuzz or wrong offset warning.

Hauke

#27 lore raw

cover b43: implement basic TX power mgmt

In reply to Rafał Miłecki

2013/3/7 Rafa? Mi?ecki <[email protected]>:

Quoted 9 lines

After spotting a lot of N-PHY-similar functions in BCM4331 dump of MMIO ops - split into names parts I was able to finally improve HT-PHY code.

It now sets TX basically, I can finally talk with devices that are few meters away, not just few centimetres. It's a little patch bomb, sorry for that, but I wasn't sure if my code is correct until it was complete and started working.

Quoted 14 lines

Rafa? Mi?ecki (13):
b43: HT-PHY: rename AFE defines
b43: HT-PHY: add classifier control function
b43: HT-PHY: move TX fix to the separated function
b43: HT-PHY: implement spurious tone avoidance
b43: HT-PHY: implement MAC reclocking
b43: HT-PHY: implement CCA reset
b43: HT-PHY: implement PA override
b43: HT-PHY: implement controlling TX power control
b43: HT-PHY: implement stopping sample tone playback
b43: HT-PHY: implement playing sample tone
b43: HT-PHY: implement RSSI polling
b43: HT-PHY: setup TX power control
b43: HT-PHY: enable basic TX power setup

I've finished sending V2 of some patches, arrays are now converted to static const where possible.

I've tried applying this 3 times and Hauke confirmed is applies cleanly, so I hope it's fine now.

Signature · 1 line
Rafa?
#28 lore raw

cover b43: implement basic TX power mgmt

Quoted 5 lines · Rafa? Mi?ecki

I've finished sending V2 of some patches, arrays are now converted to static const where possible.

I've tried applying this 3 times and Hauke confirmed is applies cleanly, so I hope it's fine now.

I do not know what happened earlier, but the using the latest set, everything applied cleanly.

Now for some testing.

Larry

#29 lore raw

cover b43: implement basic TX power mgmt

In reply to Rafał Miłecki
Quoted 8 lines · Rafa? Mi?ecki

After spotting a lot of N-PHY-similar functions in BCM4331 dump of MMIO ops - split into names parts I was able to finally improve HT-PHY code.

It now sets TX basically, I can finally talk with devices that are few meters away, not just few centimetres. It's a little patch bomb, sorry for that, but I wasn't sure if my code is correct until it was complete and started working.

If you have a git tree I can pull this from, I'd be happy to give it some testing...

Signature · 8 lines
dwmw2
-------------- next part --------------
A non-text attachment was scrubbed...
Name: smime.p7s
Type: application/x-pkcs7-signature
Size: 6171 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/b43-dev/attachments/20130313/d3474d97/attachment.bin>
#30 lore raw

cover b43: implement basic TX power mgmt

2013/3/13 David Woodhouse <[email protected]>:

Quoted 5 lines · Rafa? Mi?ecki
Quoted 4 lines

After spotting a lot of N-PHY-similar functions in BCM4331 dump of MMIO ops - split into names parts I was able to finally improve HT-PHY code.

Quoted 7 lines
Quoted 4 lines

It now sets TX basically, I can finally talk with devices that are few meters away, not just few centimetres. It's a little patch bomb, sorry for that, but I wasn't sure if my code is correct until it was complete and started working.

If you have a git tree I can pull this from, I'd be happy to give it some testing...

You can try wireless-testing:
http://git.kernel.org/cgit/linux/kernel/git/linville/wireless-testing.git

Signature · 1 line
Rafa?
#31 lore raw

cover b43: implement basic TX power mgmt

Quoted 6 lines · Rafa? Mi?ecki
Quoted 3 lines

If you have a git tree I can pull this from, I'd be happy to give it some testing...

You can try wireless-testing:
http://git.kernel.org/cgit/linux/kernel/git/linville/wireless-testing.git

Thanks. This is not an improvement here.

Sitting at my desk, about 5m from my WNDR3800 access point with walls and chimney in between them, I was previously seeing a TX rate of 48Mb/s up to 54Mb/s (reported by 'iwconfig wlan0' and also as the RX rate for the corresponding wireless client in OpenWRT's status page).

A primitive test copying a 143MiB file to a wired host would take 35 seconds, averaging 4.1MiB/s.

With these changes I get TX rates of about 18-24Mb/s and copying the same file takes 82 seconds, averaging 1.7MiB/s

That's comparing the Fedora 3.8.2-206.fc18.x86_64 kernel with current wireless-testing, rather than wireless-testing from before and after your changes. But that shouldn't matter, presumably?

Do you want me to do some more specific tests?

Signature · 8 lines
dwmw2
-------------- next part --------------
A non-text attachment was scrubbed...
Name: smime.p7s
Type: application/x-pkcs7-signature
Size: 6171 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/b43-dev/attachments/20130314/5b34893f/attachment-0001.bin>
#32 lore raw

cover b43: implement basic TX power mgmt

2013/3/14 David Woodhouse <[email protected]>:

Quoted 15 lines · Rafa? Mi?ecki
Quoted 6 lines
Quoted 3 lines

If you have a git tree I can pull this from, I'd be happy to give it some testing...

You can try wireless-testing:
http://git.kernel.org/cgit/linux/kernel/git/linville/wireless-testing.git

Thanks. This is not an improvement here.

Sitting at my desk, about 5m from my WNDR3800 access point with walls and chimney in between them, I was previously seeing a TX rate of 48Mb/s up to 54Mb/s (reported by 'iwconfig wlan0' and also as the RX rate for the corresponding wireless client in OpenWRT's status page).

Quoted 5 lines

A primitive test copying a 143MiB file to a wired host would take 35 seconds, averaging 4.1MiB/s.

With these changes I get TX rates of about 18-24Mb/s and copying the same file takes 82 seconds, averaging 1.7MiB/s

I was thinking about this and analyzing dump a bit more. My theory (that makes the most sense for me) is that:
1) Cards differ by default TX configuration. Your default configuration works pretty well in your environment (32.8Mib/s? that's really nice!). My card is probably different and in default configuration can barely transmit anything).
2) With the recent changes we put cards in some semi-optimal configuration
3) To achieve full performance we still have to implement dynamic TX power management

In your case... well it probably was better to don't touch TX power at all ;) Unfortunately it has to be finally implemented, to allow all cards work with some acceptable performance.

Quoted 5 lines

That's comparing the Fedora 3.8.2-206.fc18.x86_64 kernel with current wireless-testing, rather than wireless-testing from before and after your changes. But that shouldn't matter, presumably?

Do you want me to do some more specific tests?

To verify my theory, could you try reverting 4969b41798e512689bba57c8c44d873216eba814, AKA
b43: HT-PHY: enable basic TX power setup
? Does reverting this patch brings you back ~4.1MiB/s?

If it doesn't, could you bisect? Two another patches I would suspect;
b43: HT-PHY: implement spurious tone avoidance
b43: HT-PHY: implement MAC reclocking

Signature · 1 line
Rafa?
#33 lore raw

cover b43: implement basic TX power mgmt

Quoted 4 lines · Rafa? Mi?ecki

To verify my theory, could you try reverting 4969b41798e512689bba57c8c44d873216eba814, AKA
b43: HT-PHY: enable basic TX power setup
? Does reverting this patch brings you back ~4.1MiB/s?

Fairly much, yes.

Signature · 9 lines
dwmw2

-------------- next part --------------
A non-text attachment was scrubbed...
Name: smime.p7s
Type: application/x-pkcs7-signature
Size: 6171 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/b43-dev/attachments/20130318/48eecab4/attachment.bin>
#34 lore raw

cover b43: implement basic TX power mgmt

2013/3/18 David Woodhouse <[email protected]>:

Quoted 7 lines · Rafa? Mi?ecki
Quoted 4 lines

To verify my theory, could you try reverting 4969b41798e512689bba57c8c44d873216eba814, AKA
b43: HT-PHY: enable basic TX power setup
? Does reverting this patch brings you back ~4.1MiB/s?

Fairly much, yes.

Thanks. I'll add workaround for your card, but it needs fixing reading board info in ssb/bcma/b43.

Signature · 1 line
Rafa?