Skip to contentSkip to conversation

mtd: remove dead map drivers

PATCH Applied Artem Bityutskiy 3 participants 20 messages Mar 12, 2013 – Mar 13, 2013

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

cover mtd: remove dead map drivers

This patch-set removes a bunch of dean MTD map drivers. The way I judged whether a driver is dead or not was looking at driver's dependencies in the Kconfig file. Whenever I saw a driver depending on a Kconfig symbol which is not defined anywhere, I treated the driver as dead.

The motivation for this patch-set is to clean up the MTD subsystem a little and lessen the maintenance burden. Indeed, the less drivers we have, the easier it is to do MTD framework refactoring.

Thanks,
Artem.

#1 lore raw

PATCH 1/10 mtd: remove the dbox2-flash map driver

From: Artem Bityutskiy <[email protected]>

This driver depends on the CONFIG_DBOX2 symbol which does not exist in the kernel, which means the driver is dead.

---
 drivers/mtd/maps/Kconfig       |    8 ---
 drivers/mtd/maps/Makefile      |    1 -
 drivers/mtd/maps/dbox2-flash.c |  123 ----------------------------------------
 3 files changed, 132 deletions(-)
 delete mode 100644 drivers/mtd/maps/dbox2-flash.c
drivers/mtd/maps/Kconfig +0 -8
index 3ed17c4..74fe0c2 100644
@@ -302,14 +302,6 @@ config MTD_MBX860
 	  MBX860 board. If you have one of these boards and would like
 	  to use the flash chips on it, say 'Y'.
 
-config MTD_DBOX2
-	tristate "CFI Flash device mapped on D-Box2"
-	depends on DBOX2 && MTD_CFI_INTELSTD && MTD_CFI_INTELEXT && MTD_CFI_AMDSTD
-	help
-	  This enables access routines for the flash chips on the Nokia/Sagem
-	  D-Box 2 board. If you have one of these boards and would like to use
-	  the flash chips on it, say 'Y'.
-
 config MTD_CFI_FLAGADM
 	tristate "CFI Flash device mapping on FlagaDM"
 	depends on 8xx && MTD_CFI
drivers/mtd/maps/Makefile +0 -1
index 4ded287..93f4db2 100644
@@ -34,7 +34,6 @@ obj-$(CONFIG_MTD_TS5500)	+= ts5500_flash.o
 obj-$(CONFIG_MTD_SUN_UFLASH)	+= sun_uflash.o
 obj-$(CONFIG_MTD_VMAX)		+= vmax301.o
 obj-$(CONFIG_MTD_SCx200_DOCFLASH)+= scx200_docflash.o
-obj-$(CONFIG_MTD_DBOX2)		+= dbox2-flash.o
 obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
 obj-$(CONFIG_MTD_PCI)		+= pci.o
 obj-$(CONFIG_MTD_AUTCPU12)	+= autcpu12-nvram.o
drivers/mtd/maps/dbox2-flash.c deleted +0 -123

123 lines not on this page · raw message

Signature · 1 line
1.7.10.4
#2 lore raw

PATCH 1/10 mtd: remove the dbox2-flash map driver

In reply to Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

This driver depends on the CONFIG_DBOX2 symbol which does not exist in the kernel, which means the driver is dead.

---

Adding the PPC list

 drivers/mtd/maps/Kconfig       |    8 ---
 drivers/mtd/maps/Makefile      |    1 -
 drivers/mtd/maps/dbox2-flash.c |  123 ----------------------------------------
 3 files changed, 132 deletions(-)
 delete mode 100644 drivers/mtd/maps/dbox2-flash.c
drivers/mtd/maps/Kconfig +0 -8
index 3ed17c4..74fe0c2 100644
@@ -302,14 +302,6 @@ config MTD_MBX860
 	  MBX860 board. If you have one of these boards and would like
 	  to use the flash chips on it, say 'Y'.
 
-config MTD_DBOX2
-	tristate "CFI Flash device mapped on D-Box2"
-	depends on DBOX2 && MTD_CFI_INTELSTD && MTD_CFI_INTELEXT && MTD_CFI_AMDSTD
-	help
-	  This enables access routines for the flash chips on the Nokia/Sagem
-	  D-Box 2 board. If you have one of these boards and would like to use
-	  the flash chips on it, say 'Y'.
-
 config MTD_CFI_FLAGADM
 	tristate "CFI Flash device mapping on FlagaDM"
 	depends on 8xx && MTD_CFI
drivers/mtd/maps/Makefile +0 -1
index 4ded287..93f4db2 100644
@@ -34,7 +34,6 @@ obj-$(CONFIG_MTD_TS5500)	+= ts5500_flash.o
 obj-$(CONFIG_MTD_SUN_UFLASH)	+= sun_uflash.o
 obj-$(CONFIG_MTD_VMAX)		+= vmax301.o
 obj-$(CONFIG_MTD_SCx200_DOCFLASH)+= scx200_docflash.o
-obj-$(CONFIG_MTD_DBOX2)		+= dbox2-flash.o
 obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
 obj-$(CONFIG_MTD_PCI)		+= pci.o
 obj-$(CONFIG_MTD_AUTCPU12)	+= autcpu12-nvram.o
drivers/mtd/maps/dbox2-flash.c deleted +0 -123

123 lines not on this page · raw message

Signature · 10 lines
1.7.10.4


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

-- 
Best Regards,
Artem Bityutskiy
#3 lore raw

PATCH 2/10 mtd: remove the dmv182 map driver

In reply to Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

This driver depends on the CONFIG_DMV182 symbol which is not defined anywhere, and this means that this driver is dead.

---
 drivers/mtd/maps/Kconfig  |    9 ---
 drivers/mtd/maps/Makefile |    1 -
 drivers/mtd/maps/dmv182.c |  146 ---------------------------------------------
 3 files changed, 156 deletions(-)
 delete mode 100644 drivers/mtd/maps/dmv182.c
drivers/mtd/maps/Kconfig +0 -9
index 74fe0c2..7071486 100644
@@ -425,15 +425,6 @@ config MTD_UCLINUX
 	help
 	  Map driver to support image based filesystems for uClinux.
 
-config MTD_DMV182
-        tristate "Map driver for Dy-4 SVME/DMV-182 board."
-        depends on DMV182
-	select MTD_MAP_BANK_WIDTH_32
-	select MTD_CFI_I8
-	select MTD_CFI_AMDSTD
-        help
-          Map driver for Dy-4 SVME/DMV-182 board.
-
 config MTD_INTEL_VR_NOR
 	tristate "NOR flash on Intel Vermilion Range Expansion Bus CS0"
 	depends on PCI
drivers/mtd/maps/Makefile +0 -1
index 93f4db2..819e2ab 100644
@@ -44,7 +44,6 @@ obj-$(CONFIG_MTD_SCB2_FLASH)	+= scb2_flash.o
 obj-$(CONFIG_MTD_H720X)		+= h720x-flash.o
 obj-$(CONFIG_MTD_IXP4XX)	+= ixp4xx.o
 obj-$(CONFIG_MTD_IXP2000)	+= ixp2000.o
-obj-$(CONFIG_MTD_DMV182)	+= dmv182.o
 obj-$(CONFIG_MTD_PLATRAM)	+= plat-ram.o
 obj-$(CONFIG_MTD_INTEL_VR_NOR)	+= intel_vr_nor.o
 obj-$(CONFIG_MTD_BFIN_ASYNC)	+= bfin-async-flash.o
drivers/mtd/maps/dmv182.c deleted +0 -146

146 lines not on this page · raw message

Signature · 1 line
1.7.10.4
#4 lore raw

PATCH 2/10 mtd: remove the dmv182 map driver

In reply to Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

This driver depends on the CONFIG_DMV182 symbol which is not defined anywhere, and this means that this driver is dead.

---

Adding the PPC list

 drivers/mtd/maps/Kconfig  |    9 ---
 drivers/mtd/maps/Makefile |    1 -
 drivers/mtd/maps/dmv182.c |  146 ---------------------------------------------
 3 files changed, 156 deletions(-)
 delete mode 100644 drivers/mtd/maps/dmv182.c
drivers/mtd/maps/Kconfig +0 -9
index 74fe0c2..7071486 100644
@@ -425,15 +425,6 @@ config MTD_UCLINUX
 	help
 	  Map driver to support image based filesystems for uClinux.
 
-config MTD_DMV182
-        tristate "Map driver for Dy-4 SVME/DMV-182 board."
-        depends on DMV182
-	select MTD_MAP_BANK_WIDTH_32
-	select MTD_CFI_I8
-	select MTD_CFI_AMDSTD
-        help
-          Map driver for Dy-4 SVME/DMV-182 board.
-
 config MTD_INTEL_VR_NOR
 	tristate "NOR flash on Intel Vermilion Range Expansion Bus CS0"
 	depends on PCI
drivers/mtd/maps/Makefile +0 -1
index 93f4db2..819e2ab 100644
@@ -44,7 +44,6 @@ obj-$(CONFIG_MTD_SCB2_FLASH)	+= scb2_flash.o
 obj-$(CONFIG_MTD_H720X)		+= h720x-flash.o
 obj-$(CONFIG_MTD_IXP4XX)	+= ixp4xx.o
 obj-$(CONFIG_MTD_IXP2000)	+= ixp2000.o
-obj-$(CONFIG_MTD_DMV182)	+= dmv182.o
 obj-$(CONFIG_MTD_PLATRAM)	+= plat-ram.o
 obj-$(CONFIG_MTD_INTEL_VR_NOR)	+= intel_vr_nor.o
 obj-$(CONFIG_MTD_BFIN_ASYNC)	+= bfin-async-flash.o
drivers/mtd/maps/dmv182.c deleted +0 -146

146 lines not on this page · raw message

Signature · 10 lines
1.7.10.4


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

-- 
Best Regards,
Artem Bityutskiy
#5 lore raw

PATCH 3/10 mtd: remove the mbx860 map driver

In reply to Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

This driver depends on CONFIG_MBX which is not defined anywhere, which means this driver is dead.

---
 drivers/mtd/maps/Kconfig  |    8 ----
 drivers/mtd/maps/Makefile |    1 -
 drivers/mtd/maps/mbx860.c |   98 ---------------------------------------------
 3 files changed, 107 deletions(-)
 delete mode 100644 drivers/mtd/maps/mbx860.c
drivers/mtd/maps/Kconfig +0 -8
index 7071486..300761f 100644
@@ -294,14 +294,6 @@ config MTD_RPXLITE
 	  to communicate with the chips on the RPXLite board. More at
 	  <http://www.embeddedplanet.com/>.
 
-config MTD_MBX860
-	tristate "System flash on MBX860 board"
-	depends on MTD_CFI && MBX
-	help
-	  This enables access routines for the flash chips on the Motorola
-	  MBX860 board. If you have one of these boards and would like
-	  to use the flash chips on it, say 'Y'.
-
 config MTD_CFI_FLAGADM
 	tristate "CFI Flash device mapping on FlagaDM"
 	depends on 8xx && MTD_CFI
drivers/mtd/maps/Makefile +0 -1
index 819e2ab..b61ea98 100644
@@ -17,7 +17,6 @@ obj-$(CONFIG_MTD_ICHXROM)	+= ichxrom.o
 obj-$(CONFIG_MTD_CK804XROM)	+= ck804xrom.o
 obj-$(CONFIG_MTD_TSUNAMI)	+= tsunami_flash.o
 obj-$(CONFIG_MTD_PXA2XX)	+= pxa2xx-flash.o
-obj-$(CONFIG_MTD_MBX860)	+= mbx860.o
 obj-$(CONFIG_MTD_OCTAGON)	+= octagon-5066.o
 obj-$(CONFIG_MTD_PHYSMAP)	+= physmap.o
 obj-$(CONFIG_MTD_PHYSMAP_OF)	+= physmap_of.o
drivers/mtd/maps/mbx860.c deleted +0 -98

98 lines not on this page · raw message

Signature · 1 line
1.7.10.4
#6 lore raw

PATCH 4/10 pcmcia: remove Motorolla MBX860 support

In reply to Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

The CONFIG_MBX symbol is not defined anywhere in the kernel tree, which means this platform is not supported by the Linux kernel and we can remove the corresponding code from the 'm8xx_pcmcia' driver.

---
 drivers/pcmcia/m8xx_pcmcia.c |   59 ------------------------------------------
 1 file changed, 59 deletions(-)

NOTE: this commit is independent, and I can merge it via the MTD tree with the rest of the patches of this series. Of course, an ACK would be great to have. And of course, if PCMCIA people wish to merge it via their tree, it is also nice, just let me know.

drivers/pcmcia/m8xx_pcmcia.c +0 -59
index a3a851e..9a12ead 100644
@@ -419,65 +419,6 @@ static inline int voltage_set(int slot, int vcc, int vpp)
 
 #endif
 
-/* ------------------------------------------------------------------------- */
-/* Motorola MBX860                                                           */
-
-#if defined(CONFIG_MBX)
-
-#define PCMCIA_BOARD_MSG "MBX"
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
-	u8 reg = 0;
-
-	switch (vcc) {
-	case 0:
-		break;
-	case 33:
-		reg |= CSR2_VCC_33;
-		break;
-	case 50:
-		reg |= CSR2_VCC_50;
-		break;
-	default:
-		return 1;
-	}
-
-	switch (vpp) {
-	case 0:
-		break;
-	case 33:
-	case 50:
-		if (vcc == vpp)
-			reg |= CSR2_VPP_VCC;
-		else
-			return 1;
-		break;
-	case 120:
-		if ((vcc == 33) || (vcc == 50))
-			reg |= CSR2_VPP_12;
-		else
-			return 1;
-	default:
-		return 1;
-	}
-
-	/* first, turn off all power */
-	out_8((u8 *) MBX_CSR2_ADDR,
-	      in_8((u8 *) MBX_CSR2_ADDR) & ~(CSR2_VCC_MASK | CSR2_VPP_MASK));
-
-	/* enable new powersettings */
-	out_8((u8 *) MBX_CSR2_ADDR, in_8((u8 *) MBX_CSR2_ADDR) | reg);
-
-	return 0;
-}
-
-#define socket_get(_slot_) PCMCIA_SOCKET_KEY_5V
-#define hardware_enable(_slot_)	/* No hardware to enable */
-#define hardware_disable(_slot_)	/* No hardware to disable */
-
-#endif				/* CONFIG_MBX */
-
 #if defined(CONFIG_PRxK)
 #include <asm/cpld.h>
 extern volatile fpga_pc_regs *fpga_pc;
Signature · 1 line
1.7.10.4
#7 lore raw

PATCH 5/10 mtd: maps: kill the rpxlite map driver

In reply to Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

This driver depends on the CONFIG_RPXCLASSIC and CONFIG_RPXLITE symbols, which are not defined anywhere, and this means that this driver is dead.

---
 drivers/mtd/maps/Kconfig   |   10 -------
 drivers/mtd/maps/Makefile  |    1 -
 drivers/mtd/maps/rpxlite.c |   64 --------------------------------------------
 3 files changed, 75 deletions(-)
 delete mode 100644 drivers/mtd/maps/rpxlite.c
drivers/mtd/maps/Kconfig +0 -10
index 300761f..3fe3216 100644
@@ -284,16 +284,6 @@ config MTD_TQM8XXL
 	  code to communicate with the chips on the TQM8xxL board. More at
 	  <http://www.denx.de/wiki/PPCEmbedded/>.
 
-config MTD_RPXLITE
-	tristate "CFI Flash device mapped on RPX Lite or CLLF"
-	depends on MTD_CFI && (RPXCLASSIC || RPXLITE)
-	help
-	  The RPXLite PowerPC board has CFI-compliant chips mapped in
-	  a strange sparse mapping. This 'mapping' driver supports that
-	  arrangement, allowing the CFI probe and command set driver code
-	  to communicate with the chips on the RPXLite board. More at
-	  <http://www.embeddedplanet.com/>.
-
 config MTD_CFI_FLAGADM
 	tristate "CFI Flash device mapping on FlagaDM"
 	depends on 8xx && MTD_CFI
drivers/mtd/maps/Makefile +0 -1
index b61ea98..8e2b289 100644
@@ -23,7 +23,6 @@ obj-$(CONFIG_MTD_PHYSMAP_OF)	+= physmap_of.o
 obj-$(CONFIG_MTD_PISMO)		+= pismo.o
 obj-$(CONFIG_MTD_PMC_MSP_EVM)   += pmcmsp-flash.o
 obj-$(CONFIG_MTD_PCMCIA)	+= pcmciamtd.o
-obj-$(CONFIG_MTD_RPXLITE)	+= rpxlite.o
 obj-$(CONFIG_MTD_TQM8XXL)	+= tqm8xxl.o
 obj-$(CONFIG_MTD_SA1100)	+= sa1100-flash.o
 obj-$(CONFIG_MTD_SBC_GXX)	+= sbc_gxx.o
drivers/mtd/maps/rpxlite.c deleted +0 -64

64 lines not on this page · raw message

Signature · 1 line
1.7.10.4
#8 lore raw

PATCH 6/10 m68k: remove rpxlite stuff

In reply to Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

The CONFIG_RPXLITE is not defined anywhere, which means that this board is not supported anyway, and we can clean-up commproc.h a little.

---
 arch/m68k/include/asm/commproc.h |   17 -----------------
 1 file changed, 17 deletions(-)

NOTE: this commit is independent, and I can merge it via the MTD tree with the rest of the patches of this series. Of course, an ACK would be great to have. And of course, if m68k people wish to merge it via their tree, it is also nice, just let me know.

arch/m68k/include/asm/commproc.h +0 -17
index a739985..66a36bd 100644
@@ -480,23 +480,6 @@ typedef struct scc_enet {
 #define SICR_ENET_CLKRT	((uint)0x0000003d)
 #endif
 
-#ifdef CONFIG_RPXLITE
-/* This ENET stuff is for the MPC850 with ethernet on SCC2.  Some of
- * this may be unique to the RPX-Lite configuration.
- * Note TENA is on Port B.
- */
-#define PA_ENET_RXD	((ushort)0x0004)
-#define PA_ENET_TXD	((ushort)0x0008)
-#define PA_ENET_TCLK	((ushort)0x0200)
-#define PA_ENET_RCLK	((ushort)0x0800)
-#define PB_ENET_TENA	((uint)0x00002000)
-#define PC_ENET_CLSN	((ushort)0x0040)
-#define PC_ENET_RENA	((ushort)0x0080)
-
-#define SICR_ENET_MASK	((uint)0x0000ff00)
-#define SICR_ENET_CLKRT	((uint)0x00003d00)
-#endif
-
 #ifdef CONFIG_BSEIP
 /* This ENET stuff is for the MPC823 with ethernet on SCC2.
  * This is unique to the BSE ip-Engine board.
Signature · 1 line
1.7.10.4
#9 lore raw

PATCH 7/10 pcmcia: remove RPX board stuff

In reply to Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

The RPX board is not supported by the kernel because CONFIG_RPXCLASSIC and CONFIG_RPXLITE symbols and not defined anywhere. Clean-up the m8xx_pcmcia driver a little bit.

---
 drivers/pcmcia/m8xx_pcmcia.c |   81 ------------------------------------------
 1 file changed, 81 deletions(-)

NOTE: this commit is independent, and I can merge it via the MTD tree with the rest of the patches of this series. Of course, an ACK would be great to have. And of course, if PCMCIA people wish to merge it via their tree, it is also nice, just let me know.

drivers/pcmcia/m8xx_pcmcia.c +0 -81
index 9a12ead..18c0d8d 100644
@@ -68,12 +68,6 @@ MODULE_LICENSE("Dual MPL/GPL");
 
 #if !defined(CONFIG_PCMCIA_SLOT_A) && !defined(CONFIG_PCMCIA_SLOT_B)
 
-/* The RPX series use SLOT_B */
-#if defined(CONFIG_RPXCLASSIC) || defined(CONFIG_RPXLITE)
-#define CONFIG_PCMCIA_SLOT_B
-#define CONFIG_BD_IS_MHZ
-#endif
-
 /* The ADS board use SLOT_A */
 #ifdef CONFIG_ADS
 #define CONFIG_PCMCIA_SLOT_A
@@ -253,81 +247,6 @@ static irqreturn_t m8xx_interrupt(int irq, void *dev);
 
 #define PCMCIA_BMT_LIMIT (15*4)	/* Bus Monitor Timeout value */
 
-/* ------------------------------------------------------------------------- */
-/* board specific stuff:                                                     */
-/* voltage_set(), hardware_enable() and hardware_disable()                   */
-/* ------------------------------------------------------------------------- */
-/* RPX Boards from Embedded Planet                                           */
-
-#if defined(CONFIG_RPXCLASSIC) || defined(CONFIG_RPXLITE)
-
-/* The RPX boards seems to have it's bus monitor timeout set to 6*8 clocks.
- * SYPCR is write once only, therefore must the slowest memory be faster
- * than the bus monitor or we will get a machine check due to the bus timeout.
- */
-
-#define PCMCIA_BOARD_MSG "RPX CLASSIC or RPX LITE"
-
-#undef PCMCIA_BMT_LIMIT
-#define PCMCIA_BMT_LIMIT (6*8)
-
-static int voltage_set(int slot, int vcc, int vpp)
-{
-	u32 reg = 0;
-
-	switch (vcc) {
-	case 0:
-		break;
-	case 33:
-		reg |= BCSR1_PCVCTL4;
-		break;
-	case 50:
-		reg |= BCSR1_PCVCTL5;
-		break;
-	default:
-		return 1;
-	}
-
-	switch (vpp) {
-	case 0:
-		break;
-	case 33:
-	case 50:
-		if (vcc == vpp)
-			reg |= BCSR1_PCVCTL6;
-		else
-			return 1;
-		break;
-	case 120:
-		reg |= BCSR1_PCVCTL7;
-	default:
-		return 1;
-	}
-
-	if (!((vcc == 50) || (vcc == 0)))
-		return 1;
-
-	/* first, turn off all power */
-
-	out_be32(((u32 *) RPX_CSR_ADDR),
-		 in_be32(((u32 *) RPX_CSR_ADDR)) & ~(BCSR1_PCVCTL4 |
-						     BCSR1_PCVCTL5 |
-						     BCSR1_PCVCTL6 |
-						     BCSR1_PCVCTL7));
-
-	/* enable new powersettings */
-
-	out_be32(((u32 *) RPX_CSR_ADDR), in_be32(((u32 *) RPX_CSR_ADDR)) | reg);
-
-	return 0;
-}
-
-#define socket_get(_slot_) PCMCIA_SOCKET_KEY_5V
-#define hardware_enable(_slot_)	/* No hardware to enable */
-#define hardware_disable(_slot_)	/* No hardware to disable */
-
-#endif				/* CONFIG_RPXCLASSIC */
-
 /* FADS Boards from Motorola                                               */
 
 #if defined(CONFIG_FADS)
Signature · 1 line
1.7.10.4
#10 lore raw

PATCH 8/10 mtd: remove the tqm8xxl map driver

In reply to Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

This driver depends on the CONFIG_TQM8xxL symbol, which is not defined anywhere, which means that this driver is dead.

---
 drivers/mtd/maps/Kconfig   |   10 --
 drivers/mtd/maps/Makefile  |    1 -
 drivers/mtd/maps/tqm8xxl.c |  249 --------------------------------------------
 3 files changed, 260 deletions(-)
 delete mode 100644 drivers/mtd/maps/tqm8xxl.c
drivers/mtd/maps/Kconfig +0 -10
index 3fe3216..888e684 100644
@@ -274,16 +274,6 @@ config MTD_L440GX
 
 	  BE VERY CAREFUL.
 
-config MTD_TQM8XXL
-	tristate "CFI Flash device mapped on TQM8XXL"
-	depends on MTD_CFI && TQM8xxL
-	help
-	  The TQM8xxL PowerPC board has up to two banks of CFI-compliant
-	  chips, currently uses AMD one. This 'mapping' driver supports
-	  that arrangement, allowing the CFI probe and command set driver
-	  code to communicate with the chips on the TQM8xxL board. More at
-	  <http://www.denx.de/wiki/PPCEmbedded/>.
-
 config MTD_CFI_FLAGADM
 	tristate "CFI Flash device mapping on FlagaDM"
 	depends on 8xx && MTD_CFI
drivers/mtd/maps/Makefile +0 -1
index 8e2b289..0cdc881 100644
@@ -23,7 +23,6 @@ obj-$(CONFIG_MTD_PHYSMAP_OF)	+= physmap_of.o
 obj-$(CONFIG_MTD_PISMO)		+= pismo.o
 obj-$(CONFIG_MTD_PMC_MSP_EVM)   += pmcmsp-flash.o
 obj-$(CONFIG_MTD_PCMCIA)	+= pcmciamtd.o
-obj-$(CONFIG_MTD_TQM8XXL)	+= tqm8xxl.o
 obj-$(CONFIG_MTD_SA1100)	+= sa1100-flash.o
 obj-$(CONFIG_MTD_SBC_GXX)	+= sbc_gxx.o
 obj-$(CONFIG_MTD_SC520CDP)	+= sc520cdp.o
drivers/mtd/maps/tqm8xxl.c deleted +0 -249

249 lines not on this page · raw message

Signature · 1 line
1.7.10.4
#11 lore raw
In reply to Artem Bityutskiy
Quoted 8 lines · Artem Bityutskiy

This patch-set removes a bunch of dean MTD map drivers. The way I judged whether a driver is dead or not was looking at driver's dependencies in the Kconfig file. Whenever I saw a driver depending on a Kconfig symbol which is not defined anywhere, I treated the driver as dead.

The motivation for this patch-set is to clean up the MTD subsystem a little and lessen the maintenance burden. Indeed, the less drivers we have, the easier it is to do MTD framework refactoring.

Most of these are PPC boards, not m68k.

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

#12 lore raw

PATCH 8/10 mtd: remove the tqm8xxl map driver

In reply to Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

This driver depends on the CONFIG_TQM8xxL symbol, which is not defined anywhere, which means that this driver is dead.

---

Adding the PPC list

 drivers/mtd/maps/Kconfig   |   10 --
 drivers/mtd/maps/Makefile  |    1 -
 drivers/mtd/maps/tqm8xxl.c |  249 --------------------------------------------
 3 files changed, 260 deletions(-)
 delete mode 100644 drivers/mtd/maps/tqm8xxl.c
drivers/mtd/maps/Kconfig +0 -10
index 3fe3216..888e684 100644
@@ -274,16 +274,6 @@ config MTD_L440GX
 
 	  BE VERY CAREFUL.
 
-config MTD_TQM8XXL
-	tristate "CFI Flash device mapped on TQM8XXL"
-	depends on MTD_CFI && TQM8xxL
-	help
-	  The TQM8xxL PowerPC board has up to two banks of CFI-compliant
-	  chips, currently uses AMD one. This 'mapping' driver supports
-	  that arrangement, allowing the CFI probe and command set driver
-	  code to communicate with the chips on the TQM8xxL board. More at
-	  <http://www.denx.de/wiki/PPCEmbedded/>.
-
 config MTD_CFI_FLAGADM
 	tristate "CFI Flash device mapping on FlagaDM"
 	depends on 8xx && MTD_CFI
drivers/mtd/maps/Makefile +0 -1
index 8e2b289..0cdc881 100644
@@ -23,7 +23,6 @@ obj-$(CONFIG_MTD_PHYSMAP_OF)	+= physmap_of.o
 obj-$(CONFIG_MTD_PISMO)		+= pismo.o
 obj-$(CONFIG_MTD_PMC_MSP_EVM)   += pmcmsp-flash.o
 obj-$(CONFIG_MTD_PCMCIA)	+= pcmciamtd.o
-obj-$(CONFIG_MTD_TQM8XXL)	+= tqm8xxl.o
 obj-$(CONFIG_MTD_SA1100)	+= sa1100-flash.o
 obj-$(CONFIG_MTD_SBC_GXX)	+= sbc_gxx.o
 obj-$(CONFIG_MTD_SC520CDP)	+= sc520cdp.o
drivers/mtd/maps/tqm8xxl.c deleted +0 -249

249 lines not on this page · raw message

Signature · 10 lines
1.7.10.4


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

-- 
Best Regards,
Artem Bityutskiy
#13 lore raw

PATCH 9/10 mtd: remove the dilnetpc map driver support

In reply to Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

This driver is marked as broken for very long time. Most probably this board is just something ancient no one cares about anyway.

---
 drivers/mtd/maps/Kconfig    |   16 --
 drivers/mtd/maps/Makefile   |    1 -
 drivers/mtd/maps/dilnetpc.c |  496 -------------------------------------------
 3 files changed, 513 deletions(-)
 delete mode 100644 drivers/mtd/maps/dilnetpc.c
drivers/mtd/maps/Kconfig +0 -16
index 888e684..b6a369a 100644
@@ -249,22 +249,6 @@ config MTD_LANTIQ
 	help
 	  Support for NOR flash attached to the Lantiq SoC's External Bus Unit.
 
-config MTD_DILNETPC
-	tristate "CFI Flash device mapped on DIL/Net PC"
-	depends on X86 && MTD_CFI_INTELEXT && BROKEN
-	help
-	  MTD map driver for SSV DIL/Net PC Boards "DNP" and "ADNP".
-	  For details, see <http://www.ssv-embedded.de/ssv/pc104/p169.htm>
- 	  and <http://www.ssv-embedded.de/ssv/pc104/p170.htm>
-
-config MTD_DILNETPC_BOOTSIZE
-	hex "Size of DIL/Net PC flash boot partition"
-	depends on MTD_DILNETPC
-	default "0x80000"
-	help
-	  The amount of space taken up by the kernel or Etherboot
-	  on the DIL/Net PC flash chips.
-
 config MTD_L440GX
 	tristate "BIOS flash chip on Intel L440GX boards"
 	depends on X86 && MTD_JEDECPROBE
drivers/mtd/maps/Makefile +0 -1
index 0cdc881..7315ed8 100644
@@ -9,7 +9,6 @@ endif
 # Chip mappings
 obj-$(CONFIG_MTD_CFI_FLAGADM)	+= cfi_flagadm.o
 obj-$(CONFIG_MTD_DC21285)	+= dc21285.o
-obj-$(CONFIG_MTD_DILNETPC)	+= dilnetpc.o
 obj-$(CONFIG_MTD_L440GX)	+= l440gx.o
 obj-$(CONFIG_MTD_AMD76XROM)	+= amd76xrom.o
 obj-$(CONFIG_MTD_ESB2ROM)	+= esb2rom.o
drivers/mtd/maps/dilnetpc.c deleted +0 -496

496 lines not on this page · raw message

Signature · 1 line
1.7.10.4
#14 lore raw

PATCH 9/10 mtd: remove the dilnetpc map driver support

In reply to Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

This driver is marked as broken for very long time. Most probably this board is just something ancient no one cares about anyway.

---

Adding the PPC list

 drivers/mtd/maps/Kconfig    |   16 --
 drivers/mtd/maps/Makefile   |    1 -
 drivers/mtd/maps/dilnetpc.c |  496 -------------------------------------------
 3 files changed, 513 deletions(-)
 delete mode 100644 drivers/mtd/maps/dilnetpc.c
drivers/mtd/maps/Kconfig +0 -16
index 888e684..b6a369a 100644
@@ -249,22 +249,6 @@ config MTD_LANTIQ
 	help
 	  Support for NOR flash attached to the Lantiq SoC's External Bus Unit.
 
-config MTD_DILNETPC
-	tristate "CFI Flash device mapped on DIL/Net PC"
-	depends on X86 && MTD_CFI_INTELEXT && BROKEN
-	help
-	  MTD map driver for SSV DIL/Net PC Boards "DNP" and "ADNP".
-	  For details, see <http://www.ssv-embedded.de/ssv/pc104/p169.htm>
- 	  and <http://www.ssv-embedded.de/ssv/pc104/p170.htm>
-
-config MTD_DILNETPC_BOOTSIZE
-	hex "Size of DIL/Net PC flash boot partition"
-	depends on MTD_DILNETPC
-	default "0x80000"
-	help
-	  The amount of space taken up by the kernel or Etherboot
-	  on the DIL/Net PC flash chips.
-
 config MTD_L440GX
 	tristate "BIOS flash chip on Intel L440GX boards"
 	depends on X86 && MTD_JEDECPROBE
drivers/mtd/maps/Makefile +0 -1
index 0cdc881..7315ed8 100644
@@ -9,7 +9,6 @@ endif
 # Chip mappings
 obj-$(CONFIG_MTD_CFI_FLAGADM)	+= cfi_flagadm.o
 obj-$(CONFIG_MTD_DC21285)	+= dc21285.o
-obj-$(CONFIG_MTD_DILNETPC)	+= dilnetpc.o
 obj-$(CONFIG_MTD_L440GX)	+= l440gx.o
 obj-$(CONFIG_MTD_AMD76XROM)	+= amd76xrom.o
 obj-$(CONFIG_MTD_ESB2ROM)	+= esb2rom.o
drivers/mtd/maps/dilnetpc.c deleted +0 -496

496 lines not on this page · raw message

Signature · 10 lines
1.7.10.4


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

-- 
Best Regards,
Artem Bityutskiy
#15 lore raw

PATCH 10/10 mtd: remove the mbx860 map driver

In reply to Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

This driver depends on CONFIG_MBX which is not defined anywhere, which means this driver is dead.

---
 drivers/mtd/maps/Kconfig   |    9 --
 drivers/mtd/maps/Makefile  |    1 -
 drivers/mtd/maps/ixp2000.c |  253 --------------------------------------------
 3 files changed, 263 deletions(-)
 delete mode 100644 drivers/mtd/maps/ixp2000.c
drivers/mtd/maps/Kconfig +0 -9
index b6a369a..4b70976 100644
@@ -297,15 +297,6 @@ config MTD_IXP4XX
 	  IXDP425 and Coyote. If you have an IXP4xx based board and
 	  would like to use the flash chips on it, say 'Y'.
 
-config MTD_IXP2000
-	tristate "CFI Flash device mapped on Intel IXP2000 based systems"
-	depends on MTD_CFI && MTD_COMPLEX_MAPPINGS && ARCH_IXP2000
-	help
-	  This enables MTD access to flash devices on platforms based
-	  on Intel's IXP2000 family of network processors. If you have an
-	  IXP2000 based board and would like to use the flash chips on it,
-	  say 'Y'.
-
 config MTD_AUTCPU12
 	bool "NV-RAM mapping AUTCPU12 board"
 	depends on ARCH_AUTCPU12
drivers/mtd/maps/Makefile +0 -1
index 7315ed8..781e4b8 100644
@@ -39,7 +39,6 @@ obj-$(CONFIG_MTD_NETtel)	+= nettel.o
 obj-$(CONFIG_MTD_SCB2_FLASH)	+= scb2_flash.o
 obj-$(CONFIG_MTD_H720X)		+= h720x-flash.o
 obj-$(CONFIG_MTD_IXP4XX)	+= ixp4xx.o
-obj-$(CONFIG_MTD_IXP2000)	+= ixp2000.o
 obj-$(CONFIG_MTD_PLATRAM)	+= plat-ram.o
 obj-$(CONFIG_MTD_INTEL_VR_NOR)	+= intel_vr_nor.o
 obj-$(CONFIG_MTD_BFIN_ASYNC)	+= bfin-async-flash.o
drivers/mtd/maps/ixp2000.c deleted +0 -253

253 lines not on this page · raw message

Signature · 1 line
1.7.10.4
#16 lore raw

Re: [PATCH 10/10] mtd: remove the mbx860 map driver

Hi Artem,

I think you got the subject line and commit message mixed up with another patch. This patch looks like the ixp2000 driver, not mbx860. Might want to get the engraving on the tombstone right, eh? :)

Quoted 3 lines · Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

This driver depends on CONFIG_MBX

s/CONFIG_MBX/CONFIG_ARCH_IXP2000

Quoted 4 lines

which is not defined anywhere, which means
this driver is dead.

Brian

#17 lore raw

Re: [PATCH 10/10] mtd: remove the mbx860 map driver

Quoted 5 lines · Brian Norris

Hi Artem,

I think you got the subject line and commit message mixed up with another patch. This patch looks like the ixp2000 driver, not mbx860. Might want to get the engraving on the tombstone right, eh? :)

Indeed, lets pay the respect, I'll fix this, thanks!

Signature · 2 lines
Best Regards,
Artem Bityutskiy
#18 lore raw

PATCH 10/10 mtd: remove the ixp2000 map driver

In reply to Artem Bityutskiy

From: Artem Bityutskiy <[email protected]>

This driver depends on CONFIG_IXP2000 which is not defined anywhere, which means this driver is dead.

---

Adding the PPC list

 drivers/mtd/maps/Kconfig   |    9 --
 drivers/mtd/maps/Makefile  |    1 -
 drivers/mtd/maps/ixp2000.c |  253 --------------------------------------------
 3 files changed, 263 deletions(-)
 delete mode 100644 drivers/mtd/maps/ixp2000.c
drivers/mtd/maps/Kconfig +0 -9
index b6a369a..4b70976 100644
@@ -297,15 +297,6 @@ config MTD_IXP4XX
 	  IXDP425 and Coyote. If you have an IXP4xx based board and
 	  would like to use the flash chips on it, say 'Y'.
 
-config MTD_IXP2000
-	tristate "CFI Flash device mapped on Intel IXP2000 based systems"
-	depends on MTD_CFI && MTD_COMPLEX_MAPPINGS && ARCH_IXP2000
-	help
-	  This enables MTD access to flash devices on platforms based
-	  on Intel's IXP2000 family of network processors. If you have an
-	  IXP2000 based board and would like to use the flash chips on it,
-	  say 'Y'.
-
 config MTD_AUTCPU12
 	bool "NV-RAM mapping AUTCPU12 board"
 	depends on ARCH_AUTCPU12
drivers/mtd/maps/Makefile +0 -1
index 7315ed8..781e4b8 100644
@@ -39,7 +39,6 @@ obj-$(CONFIG_MTD_NETtel)	+= nettel.o
 obj-$(CONFIG_MTD_SCB2_FLASH)	+= scb2_flash.o
 obj-$(CONFIG_MTD_H720X)		+= h720x-flash.o
 obj-$(CONFIG_MTD_IXP4XX)	+= ixp4xx.o
-obj-$(CONFIG_MTD_IXP2000)	+= ixp2000.o
 obj-$(CONFIG_MTD_PLATRAM)	+= plat-ram.o
 obj-$(CONFIG_MTD_INTEL_VR_NOR)	+= intel_vr_nor.o
 obj-$(CONFIG_MTD_BFIN_ASYNC)	+= bfin-async-flash.o
drivers/mtd/maps/ixp2000.c deleted +0 -253

253 lines not on this page · raw message

Signature · 10 lines
1.7.10.4


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

-- 
Best Regards,
Artem Bityutskiy
author Applied
#19 lore raw
In reply to Artem Bityutskiy
Quoted 8 lines · Artem Bityutskiy

This patch-set removes a bunch of dean MTD map drivers. The way I judged whether a driver is dead or not was looking at driver's dependencies in the Kconfig file. Whenever I saw a driver depending on a Kconfig symbol which is not defined anywhere, I treated the driver as dead.

The motivation for this patch-set is to clean up the MTD subsystem a little and lessen the maintenance burden. Indeed, the less drivers we have, the easier it is to do MTD framework refactoring.

Pushed to l2-mtd.git, if there are objections, I can remove the patch(es) in question.

Signature · 2 lines
Best Regards,
Artem Bityutskiy