Skip to contentSkip to conversation

ARM: OMAP2+: GPMC clean-up and DT update

PATCH New Jon Hunter 2 participants 21 messages Mar 19, 2013 – Apr 15, 2013

Subsystems (8)
lore
Share & tools
lore

Jon Hunter

author
#0 lore raw

v4 cover ARM: OMAP2+: GPMC clean-up and DT update

While adding device-tree support for NOR memories, it became apparent that there is no common way for configuring various GPMC settings for devices that interface to the GPMC. These settings include bus-width, synchronous/asynchronous mode, burst settings, wait monitoring etc. Therefore, to simplify the GPMC code and add device-tree support for NOR, it was first necessary to consolidate how these settings are programmed.

Series based upon Mark Jackson's patch [1] and Ezequiel Garcia GPMC clean-up series [2]. Entire series available here [3].

V4 changes:
- Updated to v3.9-rc3 and fixed merge issue reported in V3 by Ezequiel.
- Fixed-up comments reported by Ezequiel.
- Made use of of_property_read_bool() as suggested by Rob Herring.
- Added "-ps" and "-ns" suffixes to GPMC DT timing properties as requested by Rob Herring to make it clearer what the timing values represent.

V3 changes:
- Rebased on RMK's IS_ERR_VALUE() patch and removed usage of IS_ERR_VALUE() from series.
- Fixed BUG in NAND code introduced in V2 by making gpmc_settings structure a local variable (I forgot to initialise structure to zero).
- Added fix from Javier to correct return value from gpmc_probe_nor().

V2 changes:
- Made gpmc_settings structure local in gpmc_nand_init().
- Use resource_size() API in probe_nor().
- Add kernel-doc for gpmc_cs_program_settings() function.
- Use of_platform_device_create() to register NOR devices in probe_nor().
- Add support for GPMC address-address-data multiplexing which required changing GPMC DT property "gpmc,mux-add-data" to store a 32-bit value and changing mux_add_data member of gpmc_settings to be a 32-bit type instead of bool.
- Add detection for incorrect GPMC chip-select base addresses.
- Cleaned-up code in gpmc_mem_init() and changed gpmc_mem_init() so that it would not return an error when the GPMC driver is being probed.

V1 changes:
- Clean-up/simplification of ONENAND initialisation code.
- Add a new GPMC structure to unify storage of various GPMC settings (that are non-timing related) for client devices and add a new function to program these settings in a common way.
- Migrate initialisation code for existing flash, usb and networking devices to use the new structure and function for GPMC settings.
- Add device-tree support for NOR flash memories.
- Add additional GPMC timing parameters to GPMC device-tree binding.
- Update GPMC NAND and ONENAND device-tree support to retrieve GPMC settings from device-tree.

Testing includes:
- Boot testing on OMAP2420 H4, OMAP3430 SDP and OMAP4430 SDP with and without device-tree present.
- OMAP2420 H4 board has NOR flash and OMAP3430 SDP has NOR, NAND and ONENAND flash. So verified that flash is detected on boot as expected. Note additional patches [4] are required for OMAP2420 H4 and OMAP3430 SDP dts files in order to enable flash memory support.
- All of the above boards use GPMC for interfacing to a networking chip and so verified that networking is working wit this series. However, please note that networking is not currently supported on these boards when booting with DT and so networking is only tested without DT.

[1] http://permalink.gmane.org/gmane.linux.ports.arm.omap/94765
[2] http://comments.gmane.org/gmane.linux.ports.arm.omap/93784
[3] https://github.com/jonhunter/linux/tree/omap-gpmc-for-v3.10
[4] https://github.com/jonhunter/linux/tree/omap-dt-for-v3.10

Javier Martinez Canillas (1):
ARM: OMAP2+: return -ENODEV if GPMC child device creation fails

Jon Hunter (17):
ARM: OMAP2+: Simplify code configuring ONENAND devices
ARM: OMAP2+: Add variable to store number of GPMC waitpins
ARM: OMAP2+: Add structure for storing GPMC settings
ARM: OMAP2+: Add function for configuring GPMC settings
ARM: OMAP2+: Convert ONENAND to use gpmc_cs_program_settings()
ARM: OMAP2+: Convert NAND to use gpmc_cs_program_settings()
ARM: OMAP2+: Convert SMC91x to use gpmc_cs_program_settings()
ARM: OMAP2+: Convert TUSB to use gpmc_cs_program_settings()
ARM: OMAP2+: Don't configure of chip-select options in
gpmc_cs_configure()
ARM: OMAP2+: Add function to read GPMC settings from device-tree
ARM: OMAP2+: Add additional GPMC timing parameters
ARM: OMAP2+: Add device-tree support for NOR flash
ARM: OMAP2+: Convert NAND to retrieve GPMC settings from DT
ARM: OMAP2+: Convert ONENAND to retrieve GPMC settings from DT
ARM: OMAP2+: Detect incorrectly aligned GPMC base address
ARM: OMAP2+: Remove unnecesssary GPMC definitions and variable
ARM: OMAP2+: Allow GPMC probe to complete even if CS mapping fails

 Documentation/devicetree/bindings/bus/ti-gpmc.txt  |  103 ++--
 Documentation/devicetree/bindings/mtd/gpmc-nor.txt |   98 ++++
 .../devicetree/bindings/mtd/gpmc-onenand.txt       |    3 +
 arch/arm/mach-omap2/gpmc-nand.c                    |   39 +-
 arch/arm/mach-omap2/gpmc-onenand.c                 |  110 +++--
 arch/arm/mach-omap2/gpmc-smc91x.c                  |   30 +-
 arch/arm/mach-omap2/gpmc.c                         |  513 +++++++++++++++-----
 arch/arm/mach-omap2/gpmc.h                         |   37 +-
 arch/arm/mach-omap2/usb-tusb6010.c                 |   62 ++-
 9 files changed, 712 insertions(+), 283 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mtd/gpmc-nor.txt
Signature · 1 line
1.7.10.4
author
#1 lore raw

PATCH v4 1/18 ARM: OMAP2+: Simplify code configuring ONENAND devices

The OMAP2+ code that configures the GPMC for ONENAND devices is copying structures between functions unnecessarily. Avoid this by passing pointers instead and simplify the code.

A pointer to structure "omap_onenand_platform_data" is passed to the function omap2_onenand_calc_sync_timings(), but only the flags member of the structure is used. Simplify the code by only passing the flags member and not the entire structure.

---
 arch/arm/mach-omap2/gpmc-onenand.c |   26 ++++++++++----------------
 1 file changed, 10 insertions(+), 16 deletions(-)
arch/arm/mach-omap2/gpmc-onenand.c +10 -16
index 4c91752..db52c4b 100644
@@ -47,10 +47,9 @@ static struct platform_device gpmc_onenand_device = {
 	.resource	= &gpmc_onenand_resource,
 };
 
-static struct gpmc_timings omap2_onenand_calc_async_timings(void)
+static void omap2_onenand_calc_async_timings(struct gpmc_timings *t)
 {
 	struct gpmc_device_timings dev_t;
-	struct gpmc_timings t;
 
 	const int t_cer = 15;
 	const int t_avdp = 12;
@@ -76,9 +75,7 @@ static struct gpmc_timings omap2_onenand_calc_async_timings(void)
 	dev_t.t_wpl = t_wpl * 1000;
 	dev_t.t_wph = t_wph * 1000;
 
-	gpmc_calc_timings(&t, &dev_t);
-
-	return t;
+	gpmc_calc_timings(t, &dev_t);
 }
 
 static int gpmc_set_async_mode(int cs, struct gpmc_timings *t)
@@ -158,12 +155,11 @@ static int omap2_onenand_get_freq(struct omap_onenand_platform_data *cfg,
 	return freq;
 }
 
-static struct gpmc_timings
-omap2_onenand_calc_sync_timings(struct omap_onenand_platform_data *cfg,
-				int freq)
+static void omap2_onenand_calc_sync_timings(struct gpmc_timings *t,
+					    unsigned int flags,
+					    int freq)
 {
 	struct gpmc_device_timings dev_t;
-	struct gpmc_timings t;
 	const int t_cer  = 15;
 	const int t_avdp = 12;
 	const int t_cez  = 20; /* max of t_cez, t_oez */
@@ -172,9 +168,9 @@ omap2_onenand_calc_sync_timings(struct omap_onenand_platform_data *cfg,
 	int min_gpmc_clk_period, t_ces, t_avds, t_avdh, t_ach, t_aavdh, t_rdyo;
 	int div, gpmc_clk_ns;
 
-	if (cfg->flags & ONENAND_SYNC_READ)
+	if (flags & ONENAND_SYNC_READ)
 		onenand_flags = ONENAND_FLAG_SYNCREAD;
-	else if (cfg->flags & ONENAND_SYNC_READWRITE)
+	else if (flags & ONENAND_SYNC_READWRITE)
 		onenand_flags = ONENAND_FLAG_SYNCREAD | ONENAND_FLAG_SYNCWRITE;
 
 	switch (freq) {
@@ -265,9 +261,7 @@ omap2_onenand_calc_sync_timings(struct omap_onenand_platform_data *cfg,
 	dev_t.cyc_aavdh_oe = 1;
 	dev_t.t_rdyo = t_rdyo * 1000 + min_gpmc_clk_period;
 
-	gpmc_calc_timings(&t, &dev_t);
-
-	return t;
+	gpmc_calc_timings(t, &dev_t);
 }
 
 static int gpmc_set_sync_mode(int cs, struct gpmc_timings *t)
@@ -300,7 +294,7 @@ static int omap2_onenand_setup_async(void __iomem *onenand_base)
 
 	omap2_onenand_set_async_mode(onenand_base);
 
-	t = omap2_onenand_calc_async_timings();
+	omap2_onenand_calc_async_timings(&t);
 
 	ret = gpmc_set_async_mode(gpmc_onenand_data->cs, &t);
 	if (ret < 0)
@@ -322,7 +316,7 @@ static int omap2_onenand_setup_sync(void __iomem *onenand_base, int *freq_ptr)
 		set_onenand_cfg(onenand_base);
 	}
 
-	t = omap2_onenand_calc_sync_timings(gpmc_onenand_data, freq);
+	omap2_onenand_calc_sync_timings(&t, gpmc_onenand_data->flags, freq);
 
 	ret = gpmc_set_sync_mode(gpmc_onenand_data->cs, &t);
 	if (ret < 0)
Signature · 1 line
1.7.10.4
author
#2 lore raw

PATCH v4 2/18 ARM: OMAP2+: Add variable to store number of GPMC waitpins

In reply to Jon Hunter

The GPMC has wait-pin signals that can be assigned to a chip-select to monitor the ready signal of an external device. Add a variable to indicate the total number of wait-pins for a given device. This will allow us to detect if the wait-pin being selected is valid or not.

When booting with device-tree read the number of wait-pins from the device-tree blob. When device-tree is not used set the number of wait-pins to 4 which is valid for OMAP2-5 devices. Newer devices that have less wait-pins (such as AM335x) only support booting with device-tree and so hard-coding the wait-pin number when not using device-tree is fine.

---
 arch/arm/mach-omap2/gpmc.c |   13 +++++++++++++
 1 file changed, 13 insertions(+)
arch/arm/mach-omap2/gpmc.c +13 -0
index 586dba7..8833c34 100644
@@ -108,6 +108,8 @@
 #define	GPMC_HAS_WR_ACCESS		0x1
 #define	GPMC_HAS_WR_DATA_MUX_BUS	0x2
 
+#define GPMC_NR_WAITPINS		4
+
 /* XXX: Only NAND irq has been considered,currently these are the only ones used
  */
 #define	GPMC_NR_IRQ		2
@@ -153,6 +155,7 @@ static struct resource	gpmc_cs_mem[GPMC_CS_NUM];
 static DEFINE_SPINLOCK(gpmc_mem_lock);
 /* Define chip-selects as reserved by default until probe completes */
 static unsigned int gpmc_cs_map = ((1 << GPMC_CS_NUM) - 1);
+static unsigned int gpmc_nr_waitpins;
 static struct device *gpmc_dev;
 static int gpmc_irq;
 static resource_size_t phys_base, mem_size;
@@ -1294,6 +1297,13 @@ static int gpmc_probe_dt(struct platform_device *pdev)
 	if (!of_id)
 		return 0;
 
+	ret = of_property_read_u32(pdev->dev.of_node, "gpmc,num-waitpins",
+				   &gpmc_nr_waitpins);
+	if (ret < 0) {
+		pr_err("%s: number of wait pins not found!\n", __func__);
+		return ret;
+	}
+
 	for_each_node_by_name(child, "nand") {
 		ret = gpmc_probe_nand_child(pdev, child);
 		if (ret < 0) {
@@ -1372,6 +1382,9 @@ static int gpmc_probe(struct platform_device *pdev)
 	/* Now the GPMC is initialised, unreserve the chip-selects */
 	gpmc_cs_map = 0;
 
+	if (!pdev->dev.of_node)
+		gpmc_nr_waitpins = GPMC_NR_WAITPINS;
+
 	rc = gpmc_probe_dt(pdev);
 	if (rc < 0) {
 		clk_disable_unprepare(gpmc_l3_clk);
Signature · 1 line
1.7.10.4
author
#3 lore raw

PATCH v4 3/18 ARM: OMAP2+: Add structure for storing GPMC settings

In reply to Jon Hunter

The GPMC has various different configuration options such as bus-width, synchronous or asychronous mode selection, burst mode options etc. Currently, there is no central structure for storing all these options when configuring the GPMC for a given device. Some of the options are stored in the GPMC timing structure and some are directly programmed into the GPMC configuration register. Add a new structure to store these options and convert code to use this structure. Adding this structure will allow us to create a common function for configuring these options.

---
 arch/arm/mach-omap2/gpmc-onenand.c |   18 ++++++++++-----
 arch/arm/mach-omap2/gpmc-smc91x.c  |    2 +-
 arch/arm/mach-omap2/gpmc.c         |   45 +++++++++++++++++++++---------------
 arch/arm/mach-omap2/gpmc.h         |   28 ++++++++++++++++------
 arch/arm/mach-omap2/usb-tusb6010.c |   19 ++++++++-------
 5 files changed, 72 insertions(+), 40 deletions(-)
arch/arm/mach-omap2/gpmc-onenand.c +12 -6
index db52c4b..e175ceb 100644
@@ -47,6 +47,15 @@ static struct platform_device gpmc_onenand_device = {
 	.resource	= &gpmc_onenand_resource,
 };
 
+static struct gpmc_settings onenand_async = {
+	.mux_add_data	= GPMC_MUX_AD,
+};
+
+static struct gpmc_settings onenand_sync = {
+	.burst_read	= true,
+	.mux_add_data	= GPMC_MUX_AD,
+};
+
 static void omap2_onenand_calc_async_timings(struct gpmc_timings *t)
 {
 	struct gpmc_device_timings dev_t;
@@ -63,7 +72,6 @@ static void omap2_onenand_calc_async_timings(struct gpmc_timings *t)
 
 	memset(&dev_t, 0, sizeof(dev_t));
 
-	dev_t.mux = true;
 	dev_t.t_avdp_r = max_t(int, t_avdp, t_cer) * 1000;
 	dev_t.t_avdp_w = dev_t.t_avdp_r;
 	dev_t.t_aavdh = t_aavdh * 1000;
@@ -75,7 +83,7 @@ static void omap2_onenand_calc_async_timings(struct gpmc_timings *t)
 	dev_t.t_wpl = t_wpl * 1000;
 	dev_t.t_wph = t_wph * 1000;
 
-	gpmc_calc_timings(t, &dev_t);
+	gpmc_calc_timings(t, &onenand_async, &dev_t);
 }
 
 static int gpmc_set_async_mode(int cs, struct gpmc_timings *t)
@@ -235,10 +243,8 @@ static void omap2_onenand_calc_sync_timings(struct gpmc_timings *t,
 	/* Set synchronous read timings */
 	memset(&dev_t, 0, sizeof(dev_t));
 
-	dev_t.mux = true;
-	dev_t.sync_read = true;
 	if (onenand_flags & ONENAND_FLAG_SYNCWRITE) {
-		dev_t.sync_write = true;
+		onenand_sync.sync_write = true;
 	} else {
 		dev_t.t_avdp_w = max(t_avdp, t_cer) * 1000;
 		dev_t.t_wpl = t_wpl * 1000;
@@ -261,7 +267,7 @@ static void omap2_onenand_calc_sync_timings(struct gpmc_timings *t,
 	dev_t.cyc_aavdh_oe = 1;
 	dev_t.t_rdyo = t_rdyo * 1000 + min_gpmc_clk_period;
 
-	gpmc_calc_timings(t, &dev_t);
+	gpmc_calc_timings(t, &onenand_sync, &dev_t);
 }
 
 static int gpmc_set_sync_mode(int cs, struct gpmc_timings *t)
arch/arm/mach-omap2/gpmc-smc91x.c +1 -1
index 11d0b75..4b78338 100644
@@ -104,7 +104,7 @@ static int smc91c96_gpmc_retime(void)
 	dev_t.t_cez_w = t4_w * 1000;
 	dev_t.t_wr_cycle = (t20 - t3) * 1000;
 
-	gpmc_calc_timings(&t, &dev_t);
+	gpmc_calc_timings(&t, NULL, &dev_t);
 
 	return gpmc_cs_set_timings(gpmc_cfg->cs, &t);
 }
arch/arm/mach-omap2/gpmc.c +27 -18

98 lines not on this page · raw message

arch/arm/mach-omap2/gpmc.h +21 -7
index 697ff42..39e4e04 100644
@@ -60,8 +60,8 @@
 #define GPMC_CONFIG1_DEVICETYPE_NOR     GPMC_CONFIG1_DEVICETYPE(0)
 #define GPMC_CONFIG1_MUXTYPE(val)       ((val & 3) << 8)
 #define GPMC_CONFIG1_MUXNONMUX          GPMC_CONFIG1_MUXTYPE(0)
-#define GPMC_CONFIG1_MUXAAD             GPMC_CONFIG1_MUXTYPE(1)
-#define GPMC_CONFIG1_MUXADDDATA         GPMC_CONFIG1_MUXTYPE(2)
+#define GPMC_CONFIG1_MUXAAD             GPMC_CONFIG1_MUXTYPE(GPMC_MUX_AAD)
+#define GPMC_CONFIG1_MUXADDDATA         GPMC_CONFIG1_MUXTYPE(GPMC_MUX_AD)
 #define GPMC_CONFIG1_TIME_PARA_GRAN     (1 << 4)
 #define GPMC_CONFIG1_FCLK_DIV(val)      (val & 3)
 #define GPMC_CONFIG1_FCLK_DIV2          (GPMC_CONFIG1_FCLK_DIV(1))
@@ -76,6 +76,8 @@
 #define GPMC_IRQ_FIFOEVENTENABLE	0x01
 #define GPMC_IRQ_COUNT_EVENT		0x02
 
+#define GPMC_MUX_AAD			1	/* Addr-Addr-Data multiplex */
+#define GPMC_MUX_AD			2	/* Addr-Data multiplex */
 
 /* bool type time settings */
 struct gpmc_bool_timings {
@@ -181,10 +183,6 @@ struct gpmc_device_timings {
 	u8 cyc_wpl;	/* write deassertion time in cycles */
 	u32 cyc_iaa;	/* initial access time in cycles */
 
-	bool mux;	/* address & data muxed */
-	bool sync_write;/* synchronous write */
-	bool sync_read;	/* synchronous read */
-
 	/* extra delays */
 	bool ce_xdelay;
 	bool avd_xdelay;
@@ -192,8 +190,24 @@ struct gpmc_device_timings {
 	bool we_xdelay;
 };
 
+struct gpmc_settings {
+	bool burst_wrap;	/* enables wrap bursting */
+	bool burst_read;	/* enables read page/burst mode */
+	bool burst_write;	/* enables write page/burst mode */
+	bool device_nand;	/* device is NAND */
+	bool sync_read;		/* enables synchronous reads */
+	bool sync_write;	/* enables synchronous writes */
+	bool wait_on_read;	/* monitor wait on reads */
+	bool wait_on_write;	/* monitor wait on writes */
+	u32 burst_len;		/* page/burst length */
+	u32 device_width;	/* device bus width (8 or 16 bit) */
+	u32 mux_add_data;	/* multiplex address & data */
+	u32 wait_pin;		/* wait-pin to be used */
+};
+
 extern int gpmc_calc_timings(struct gpmc_timings *gpmc_t,
-				struct gpmc_device_timings *dev_t);
+			     struct gpmc_settings *gpmc_s,
+			     struct gpmc_device_timings *dev_t);
 
 extern void gpmc_update_nand_reg(struct gpmc_nand_regs *reg, int cs);
 extern int gpmc_get_client_irq(unsigned irq_config);
arch/arm/mach-omap2/usb-tusb6010.c +11 -8
index c5a3c6f..faaf96d 100644
@@ -26,6 +26,15 @@
 static u8		async_cs, sync_cs;
 static unsigned		refclk_psec;
 
+static struct gpmc_settings tusb_async = {
+	.mux_add_data	= GPMC_MUX_AD,
+};
+
+static struct gpmc_settings tusb_sync = {
+	.sync_read	= true,
+	.sync_write	= true,
+	.mux_add_data	= GPMC_MUX_AD,
+};
 
 /* NOTE:  timings are from tusb 6010 datasheet Rev 1.8, 12-Sept 2006 */
 
@@ -37,8 +46,6 @@ static int tusb_set_async_mode(unsigned sysclk_ps)
 
 	memset(&dev_t, 0, sizeof(dev_t));
 
-	dev_t.mux = true;
-
 	dev_t.t_ceasu = 8 * 1000;
 	dev_t.t_avdasu = t_acsnh_advnh - 7000;
 	dev_t.t_ce_avd = 1000;
@@ -52,7 +59,7 @@ static int tusb_set_async_mode(unsigned sysclk_ps)
 	dev_t.t_wpl = 300;
 	dev_t.cyc_aavdh_we = 1;
 
-	gpmc_calc_timings(&t, &dev_t);
+	gpmc_calc_timings(&t, &tusb_async, &dev_t);
 
 	return gpmc_cs_set_timings(async_cs, &t);
 }
@@ -65,10 +72,6 @@ static int tusb_set_sync_mode(unsigned sysclk_ps)
 
 	memset(&dev_t, 0, sizeof(dev_t));
 
-	dev_t.mux = true;
-	dev_t.sync_read = true;
-	dev_t.sync_write = true;
-
 	dev_t.clk = 11100;
 	dev_t.t_bacc = 1000;
 	dev_t.t_ces = 1000;
@@ -84,7 +87,7 @@ static int tusb_set_sync_mode(unsigned sysclk_ps)
 	dev_t.cyc_wpl = 6;
 	dev_t.t_ce_rdyz = 7000;
 
-	gpmc_calc_timings(&t, &dev_t);
+	gpmc_calc_timings(&t, &tusb_sync, &dev_t);
 
 	return gpmc_cs_set_timings(sync_cs, &t);
 }
Signature · 1 line
1.7.10.4
author
#4 lore raw

PATCH v4 4/18 ARM: OMAP2+: Add function for configuring GPMC settings

In reply to Jon Hunter

The GPMC has various different configuration options such as bus-width, synchronous or asychronous mode selection, burst mode options etc. Currently, there is no common function for configuring these options and various devices set these options by either programming the GPMC CONFIG1 register directly or by calling gpmc_cs_configure() to set some of the options.

Add a new function for configuring all of the GPMC options. Having a common function for configuring this options will simplify code and ease the migration to device-tree.

Also add a new capability flag to detect devices that support the address-address-data multiplexing mode.

---
 arch/arm/mach-omap2/gpmc.c |  100 ++++++++++++++++++++++++++++++++++++++++++++
 arch/arm/mach-omap2/gpmc.h |    6 +++
 2 files changed, 106 insertions(+)
arch/arm/mach-omap2/gpmc.c +100 -0
index 20747fb..ee5d0e9 100644
@@ -107,6 +107,7 @@
 
 #define	GPMC_HAS_WR_ACCESS		0x1
 #define	GPMC_HAS_WR_DATA_MUX_BUS	0x2
+#define	GPMC_HAS_MUX_AAD		0x4
 
 #define GPMC_NR_WAITPINS		4
 
@@ -1126,6 +1127,90 @@ int gpmc_calc_timings(struct gpmc_timings *gpmc_t,
 	return 0;
 }
 
+/**
+ * gpmc_cs_program_settings - programs non-timing related settings
+ * @cs:		GPMC chip-select to program
+ * @p:		pointer to GPMC settings structure
+ *
+ * Programs non-timing related settings for a GPMC chip-select, such as
+ * bus-width, burst configuration, etc. Function should be called once
+ * for each chip-select that is being used and must be called before
+ * calling gpmc_cs_set_timings() as timing parameters in the CONFIG1
+ * register will be initialised to zero by this function. Returns 0 on
+ * success and appropriate negative error code on failure.
+ */
+int gpmc_cs_program_settings(int cs, struct gpmc_settings *p)
+{
+	u32 config1;
+
+	if ((!p->device_width) || (p->device_width > GPMC_DEVWIDTH_16BIT)) {
+		pr_err("%s: invalid width %d!", __func__, p->device_width);
+		return -EINVAL;
+	}
+
+	/* Address-data multiplexing not supported for NAND devices */
+	if (p->device_nand && p->mux_add_data) {
+		pr_err("%s: invalid configuration!\n", __func__);
+		return -EINVAL;
+	}
+
+	if ((p->mux_add_data > GPMC_MUX_AD) ||
+	    ((p->mux_add_data == GPMC_MUX_AAD) &&
+	     !(gpmc_capability & GPMC_HAS_MUX_AAD))) {
+		pr_err("%s: invalid multiplex configuration!\n", __func__);
+		return -EINVAL;
+	}
+
+	/* Page/burst mode supports lengths of 4, 8 and 16 bytes */
+	if (p->burst_read || p->burst_write) {
+		switch (p->burst_len) {
+		case GPMC_BURST_4:
+		case GPMC_BURST_8:
+		case GPMC_BURST_16:
+			break;
+		default:
+			pr_err("%s: invalid page/burst-length (%d)\n",
+			       __func__, p->burst_len);
+			return -EINVAL;
+		}
+	}
+
+	if ((p->wait_on_read || p->wait_on_write) &&
+	    (p->wait_pin > gpmc_nr_waitpins)) {
+		pr_err("%s: invalid wait-pin (%d)\n", __func__, p->wait_pin);
+		return -EINVAL;
+	}
+
+	config1 = GPMC_CONFIG1_DEVICESIZE((p->device_width - 1));
+
+	if (p->sync_read)
+		config1 |= GPMC_CONFIG1_READTYPE_SYNC;
+	if (p->sync_write)
+		config1 |= GPMC_CONFIG1_WRITETYPE_SYNC;
+	if (p->wait_on_read)
+		config1 |= GPMC_CONFIG1_WAIT_READ_MON;
+	if (p->wait_on_write)
+		config1 |= GPMC_CONFIG1_WAIT_WRITE_MON;
+	if (p->wait_on_read || p->wait_on_write)
+		config1 |= GPMC_CONFIG1_WAIT_PIN_SEL(p->wait_pin);
+	if (p->device_nand)
+		config1	|= GPMC_CONFIG1_DEVICETYPE(GPMC_DEVICETYPE_NAND);
+	if (p->mux_add_data)
+		config1	|= GPMC_CONFIG1_MUXTYPE(p->mux_add_data);
+	if (p->burst_read)
+		config1 |= GPMC_CONFIG1_READMULTIPLE_SUPP;
+	if (p->burst_write)
+		config1 |= GPMC_CONFIG1_WRITEMULTIPLE_SUPP;
+	if (p->burst_read || p->burst_write) {
+		config1 |= GPMC_CONFIG1_PAGE_LEN(p->burst_len >> 3);
+		config1 |= p->burst_wrap ? GPMC_CONFIG1_WRAPBURST_SUPP : 0;
+	}
+
+	gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1, config1);
+
+	return 0;
+}
+
 #ifdef CONFIG_OF
 static struct of_device_id gpmc_dt_ids[] = {
 	{ .compatible = "ti,omap2420-gpmc" },
@@ -1372,8 +1457,23 @@ static int gpmc_probe(struct platform_device *pdev)
 	gpmc_dev = &pdev->dev;
 
 	l = gpmc_read_reg(GPMC_REVISION);
+
+	/*
+	 * FIXME: Once device-tree migration is complete the below flags
+	 * should be populated based upon the device-tree compatible
+	 * string. For now just use the IP revision. OMAP3+ devices have
+	 * the wr_access and wr_data_mux_bus register fields. OMAP4+
+	 * devices support the addr-addr-data multiplex protocol.
+	 *
+	 * GPMC IP revisions:
+	 * - OMAP24xx			= 2.0
+	 * - OMAP3xxx			= 5.0
+	 * - OMAP44xx/54xx/AM335x	= 6.0
+	 */
 	if (GPMC_REVISION_MAJOR(l) > 0x4)
 		gpmc_capability = GPMC_HAS_WR_ACCESS | GPMC_HAS_WR_DATA_MUX_BUS;
+	if (GPMC_REVISION_MAJOR(l) > 0x5)
+		gpmc_capability |= GPMC_HAS_MUX_AAD;
 	dev_info(gpmc_dev, "GPMC revision %d.%d\n", GPMC_REVISION_MAJOR(l),
 		 GPMC_REVISION_MINOR(l));
 
arch/arm/mach-omap2/gpmc.h +6 -0
index 39e4e04..ce6ae21 100644
@@ -76,6 +76,11 @@
 #define GPMC_IRQ_FIFOEVENTENABLE	0x01
 #define GPMC_IRQ_COUNT_EVENT		0x02
 
+#define GPMC_BURST_4			4	/* 4 word burst */
+#define GPMC_BURST_8			8	/* 8 word burst */
+#define GPMC_BURST_16			16	/* 16 word burst */
+#define GPMC_DEVWIDTH_8BIT		1	/* 8-bit device width */
+#define GPMC_DEVWIDTH_16BIT		2	/* 16-bit device width */
 #define GPMC_MUX_AAD			1	/* Addr-Addr-Data multiplex */
 #define GPMC_MUX_AD			2	/* Addr-Data multiplex */
 
@@ -217,6 +222,7 @@ extern unsigned int gpmc_ticks_to_ns(unsigned int ticks);
 extern void gpmc_cs_write_reg(int cs, int idx, u32 val);
 extern int gpmc_calc_divider(unsigned int sync_clk);
 extern int gpmc_cs_set_timings(int cs, const struct gpmc_timings *t);
+extern int gpmc_cs_program_settings(int cs, struct gpmc_settings *p);
 extern int gpmc_cs_request(int cs, unsigned long size, unsigned long *base);
 extern void gpmc_cs_free(int cs);
 extern void omap3_gpmc_save_context(void);
Signature · 1 line
1.7.10.4
author
#5 lore raw

PATCH v4 5/18 ARM: OMAP2+: Convert ONENAND to use gpmc_cs_program_settings()

In reply to Jon Hunter

Convert the OMAP2+ ONENAND code to use the gpmc_cs_program_settings() function for configuring the various GPMC options instead of directly programming the CONFIG1 register.

---
 arch/arm/mach-omap2/gpmc-onenand.c |   61 +++++++++++++++---------------------
 1 file changed, 25 insertions(+), 36 deletions(-)
arch/arm/mach-omap2/gpmc-onenand.c +25 -36
index e175ceb..46aac83 100644
@@ -48,18 +48,22 @@ static struct platform_device gpmc_onenand_device = {
 };
 
 static struct gpmc_settings onenand_async = {
+	.device_width	= GPMC_DEVWIDTH_16BIT,
 	.mux_add_data	= GPMC_MUX_AD,
 };
 
 static struct gpmc_settings onenand_sync = {
 	.burst_read	= true,
+	.burst_wrap	= true,
+	.burst_len	= GPMC_BURST_16,
+	.device_width	= GPMC_DEVWIDTH_16BIT,
 	.mux_add_data	= GPMC_MUX_AD,
+	.wait_pin	= 0,
 };
 
 static void omap2_onenand_calc_async_timings(struct gpmc_timings *t)
 {
 	struct gpmc_device_timings dev_t;
-
 	const int t_cer = 15;
 	const int t_avdp = 12;
 	const int t_aavdh = 7;
@@ -86,16 +90,6 @@ static void omap2_onenand_calc_async_timings(struct gpmc_timings *t)
 	gpmc_calc_timings(t, &onenand_async, &dev_t);
 }
 
-static int gpmc_set_async_mode(int cs, struct gpmc_timings *t)
-{
-	/* Configure GPMC for asynchronous read */
-	gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1,
-			  GPMC_CONFIG1_DEVICESIZE_16 |
-			  GPMC_CONFIG1_MUXADDDATA);
-
-	return gpmc_cs_set_timings(cs, t);
-}
-
 static void omap2_onenand_set_async_mode(void __iomem *onenand_base)
 {
 	u32 reg;
@@ -243,8 +237,11 @@ static void omap2_onenand_calc_sync_timings(struct gpmc_timings *t,
 	/* Set synchronous read timings */
 	memset(&dev_t, 0, sizeof(dev_t));
 
+	if (onenand_flags & ONENAND_FLAG_SYNCREAD)
+		onenand_sync.sync_read = true;
 	if (onenand_flags & ONENAND_FLAG_SYNCWRITE) {
 		onenand_sync.sync_write = true;
+		onenand_sync.burst_write = true;
 	} else {
 		dev_t.t_avdp_w = max(t_avdp, t_cer) * 1000;
 		dev_t.t_wpl = t_wpl * 1000;
@@ -270,29 +267,6 @@ static void omap2_onenand_calc_sync_timings(struct gpmc_timings *t,
 	gpmc_calc_timings(t, &onenand_sync, &dev_t);
 }
 
-static int gpmc_set_sync_mode(int cs, struct gpmc_timings *t)
-{
-	unsigned sync_read = onenand_flags & ONENAND_FLAG_SYNCREAD;
-	unsigned sync_write = onenand_flags & ONENAND_FLAG_SYNCWRITE;
-
-	/* Configure GPMC for synchronous read */
-	gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1,
-			  GPMC_CONFIG1_WRAPBURST_SUPP |
-			  GPMC_CONFIG1_READMULTIPLE_SUPP |
-			  (sync_read ? GPMC_CONFIG1_READTYPE_SYNC : 0) |
-			  (sync_write ? GPMC_CONFIG1_WRITEMULTIPLE_SUPP : 0) |
-			  (sync_write ? GPMC_CONFIG1_WRITETYPE_SYNC : 0) |
-			  GPMC_CONFIG1_PAGE_LEN(2) |
-			  (cpu_is_omap34xx() ? 0 :
-				(GPMC_CONFIG1_WAIT_READ_MON |
-				 GPMC_CONFIG1_WAIT_PIN_SEL(0))) |
-			  GPMC_CONFIG1_DEVICESIZE_16 |
-			  GPMC_CONFIG1_DEVICETYPE_NOR |
-			  GPMC_CONFIG1_MUXADDDATA);
-
-	return gpmc_cs_set_timings(cs, t);
-}
-
 static int omap2_onenand_setup_async(void __iomem *onenand_base)
 {
 	struct gpmc_timings t;
@@ -302,7 +276,11 @@ static int omap2_onenand_setup_async(void __iomem *onenand_base)
 
 	omap2_onenand_calc_async_timings(&t);
 
-	ret = gpmc_set_async_mode(gpmc_onenand_data->cs, &t);
+	ret = gpmc_cs_program_settings(gpmc_onenand_data->cs, &onenand_async);
+	if (ret < 0)
+		return ret;
+
+	ret = gpmc_cs_set_timings(gpmc_onenand_data->cs, &t);
 	if (ret < 0)
 		return ret;
 
@@ -322,9 +300,20 @@ static int omap2_onenand_setup_sync(void __iomem *onenand_base, int *freq_ptr)
 		set_onenand_cfg(onenand_base);
 	}
 
+	/*
+	 * FIXME: Appears to be legacy code from initial ONENAND commit.
+	 * Unclear what boards this is for and if this can be removed.
+	 */
+	if (!cpu_is_omap34xx())
+		onenand_sync.wait_on_read = true;
+
 	omap2_onenand_calc_sync_timings(&t, gpmc_onenand_data->flags, freq);
 
-	ret = gpmc_set_sync_mode(gpmc_onenand_data->cs, &t);
+	ret = gpmc_cs_program_settings(gpmc_onenand_data->cs, &onenand_sync);
+	if (ret < 0)
+		return ret;
+
+	ret = gpmc_cs_set_timings(gpmc_onenand_data->cs, &t);
 	if (ret < 0)
 		return ret;
 
Signature · 1 line
1.7.10.4
author
#6 lore raw

PATCH v4 6/18 ARM: OMAP2+: Convert NAND to use gpmc_cs_program_settings()

In reply to Jon Hunter

Convert the OMAP2+ NAND code to use the gpmc_cs_program_settings() function for configuring the various GPMC options instead of directly programming the CONFIG1 register.

This moves the configuration of some GPMC options outside the nand_gpmc_retime() because these options should only need to be set once regardless of whether the gpmc timing is changing dynamically at runtime. The programming of where the wait-pin is also moved slightly, but this will not have any impact to existing devices as no boards are currently setting the dev_ready variable.

---
 arch/arm/mach-omap2/gpmc-nand.c |   35 +++++++++++++++++++++++------------
 1 file changed, 23 insertions(+), 12 deletions(-)
arch/arm/mach-omap2/gpmc-nand.c +23 -12
index e50e438..75feb95 100644
@@ -74,14 +74,6 @@ static int omap2_nand_gpmc_retime(
 	t.cs_wr_off = gpmc_t->cs_wr_off;
 	t.wr_cycle = gpmc_t->wr_cycle;
 
-	/* Configure GPMC */
-	if (gpmc_nand_data->devsize == NAND_BUSWIDTH_16)
-		gpmc_cs_configure(gpmc_nand_data->cs, GPMC_CONFIG_DEV_SIZE, 1);
-	else
-		gpmc_cs_configure(gpmc_nand_data->cs, GPMC_CONFIG_DEV_SIZE, 0);
-	gpmc_cs_configure(gpmc_nand_data->cs,
-			GPMC_CONFIG_DEV_TYPE, GPMC_DEVICETYPE_NAND);
-	gpmc_cs_configure(gpmc_nand_data->cs, GPMC_CONFIG_WP, 0);
 	err = gpmc_cs_set_timings(gpmc_nand_data->cs, &t);
 	if (err)
 		return err;
@@ -115,8 +107,11 @@ int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
 		   struct gpmc_timings *gpmc_t)
 {
 	int err	= 0;
+	struct gpmc_settings s;
 	struct device *dev = &gpmc_nand_device.dev;
 
+	memset(&s, 0, sizeof(struct gpmc_settings));
+
 	gpmc_nand_device.dev.platform_data = gpmc_nand_data;
 
 	err = gpmc_cs_request(gpmc_nand_data->cs, NAND_IO_SIZE,
@@ -141,11 +136,27 @@ int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
 			dev_err(dev, "Unable to set gpmc timings: %d\n", err);
 			return err;
 		}
-	}
 
-	/* Enable RD PIN Monitoring Reg */
-	if (gpmc_nand_data->dev_ready) {
-		gpmc_cs_configure(gpmc_nand_data->cs, GPMC_CONFIG_RDY_BSY, 1);
+		s.device_nand = true;
+
+		/* Enable RD PIN Monitoring Reg */
+		if (gpmc_nand_data->dev_ready) {
+			s.wait_on_read = true;
+			s.wait_on_write = true;
+		}
+
+		if (gpmc_nand_data->devsize == NAND_BUSWIDTH_16)
+			s.device_width = GPMC_DEVWIDTH_16BIT;
+		else
+			s.device_width = GPMC_DEVWIDTH_8BIT;
+
+		err = gpmc_cs_program_settings(gpmc_nand_data->cs, &s);
+		if (err < 0)
+			goto out_free_cs;
+
+		err = gpmc_cs_configure(gpmc_nand_data->cs, GPMC_CONFIG_WP, 0);
+		if (err < 0)
+			goto out_free_cs;
 	}
 
 	gpmc_update_nand_reg(&gpmc_nand_data->reg, gpmc_nand_data->cs);
Signature · 1 line
1.7.10.4
author
#7 lore raw

PATCH v4 7/18 ARM: OMAP2+: Convert SMC91x to use gpmc_cs_program_settings()

In reply to Jon Hunter

Convert the OMAP2+ SMC91x code to use the gpmc_cs_program_settings() function for configuring the various GPMC options instead of directly programming the CONFIG1 register.

Move configuration of the GPMC settings outside retime function and this does not need to be done if the timings are changed dynamically at runtime.

---
 arch/arm/mach-omap2/gpmc-smc91x.c |   30 +++++++++++++++++-------------
 1 file changed, 17 insertions(+), 13 deletions(-)
arch/arm/mach-omap2/gpmc-smc91x.c +17 -13
index 4b78338..61a0635 100644
@@ -49,6 +49,10 @@ static struct platform_device gpmc_smc91x_device = {
 	.resource	= gpmc_smc91x_resources,
 };
 
+static struct gpmc_settings smc91x_settings = {
+	.device_width = GPMC_DEVWIDTH_16BIT,
+};
+
 /*
  * Set the gpmc timings for smc91c96. The timings are taken
  * from the data sheet available at:
@@ -67,18 +71,6 @@ static int smc91c96_gpmc_retime(void)
 	const int t7 = 5;	/* Figure 12.4 write */
 	const int t8 = 5;	/* Figure 12.4 write */
 	const int t20 = 185;	/* Figure 12.2 read and 12.4 write */
-	u32 l;
-
-	l = GPMC_CONFIG1_DEVICESIZE_16;
-	if (gpmc_cfg->flags & GPMC_MUX_ADD_DATA)
-		l |= GPMC_CONFIG1_MUXADDDATA;
-	if (gpmc_cfg->flags & GPMC_READ_MON)
-		l |= GPMC_CONFIG1_WAIT_READ_MON;
-	if (gpmc_cfg->flags & GPMC_WRITE_MON)
-		l |= GPMC_CONFIG1_WAIT_WRITE_MON;
-	if (gpmc_cfg->wait_pin)
-		l |= GPMC_CONFIG1_WAIT_PIN_SEL(gpmc_cfg->wait_pin);
-	gpmc_cs_write_reg(gpmc_cfg->cs, GPMC_CS_CONFIG1, l);
 
 	/*
 	 * FIXME: Calculate the address and data bus muxed timings.
@@ -104,7 +96,7 @@ static int smc91c96_gpmc_retime(void)
 	dev_t.t_cez_w = t4_w * 1000;
 	dev_t.t_wr_cycle = (t20 - t3) * 1000;
 
-	gpmc_calc_timings(&t, NULL, &dev_t);
+	gpmc_calc_timings(&t, &smc91x_settings, &dev_t);
 
 	return gpmc_cs_set_timings(gpmc_cfg->cs, &t);
 }
@@ -133,6 +125,18 @@ void __init gpmc_smc91x_init(struct omap_smc91x_platform_data *board_data)
 	gpmc_smc91x_resources[0].end = cs_mem_base + 0x30f;
 	gpmc_smc91x_resources[1].flags |= (gpmc_cfg->flags & IRQF_TRIGGER_MASK);
 
+	if (gpmc_cfg->flags & GPMC_MUX_ADD_DATA)
+		smc91x_settings.mux_add_data = GPMC_MUX_AD;
+	if (gpmc_cfg->flags & GPMC_READ_MON)
+		smc91x_settings.wait_on_read = true;
+	if (gpmc_cfg->flags & GPMC_WRITE_MON)
+		smc91x_settings.wait_on_write = true;
+	if (gpmc_cfg->wait_pin)
+		smc91x_settings.wait_pin = gpmc_cfg->wait_pin;
+	ret = gpmc_cs_program_settings(gpmc_cfg->cs, &smc91x_settings);
+	if (ret < 0)
+		goto free1;
+
 	if (gpmc_cfg->retime) {
 		ret = gpmc_cfg->retime();
 		if (ret != 0)
Signature · 1 line
1.7.10.4
author
#8 lore raw

PATCH v4 8/18 ARM: OMAP2+: Convert TUSB to use gpmc_cs_program_settings()

In reply to Jon Hunter

Convert the OMAP2+ TUSB code to use the gpmc_cs_program_settings() function for configuring the various GPMC options instead of directly programming the CONFIG1 register.

---
 arch/arm/mach-omap2/usb-tusb6010.c |   43 ++++++++++++++++--------------------
 1 file changed, 19 insertions(+), 24 deletions(-)
arch/arm/mach-omap2/usb-tusb6010.c +19 -24
index faaf96d..e832bc7 100644
@@ -8,6 +8,7 @@
  * published by the Free Software Foundation.
  */
 
+#include <linux/err.h>
 #include <linux/string.h>
 #include <linux/types.h>
 #include <linux/errno.h>
@@ -27,12 +28,21 @@ static u8		async_cs, sync_cs;
 static unsigned		refclk_psec;
 
 static struct gpmc_settings tusb_async = {
+	.wait_on_read	= true,
+	.wait_on_write	= true,
+	.device_width	= GPMC_DEVWIDTH_16BIT,
 	.mux_add_data	= GPMC_MUX_AD,
 };
 
 static struct gpmc_settings tusb_sync = {
+	.burst_read	= true,
+	.burst_write	= true,
 	.sync_read	= true,
 	.sync_write	= true,
+	.wait_on_read	= true,
+	.wait_on_write	= true,
+	.burst_len	= GPMC_BURST_16,
+	.device_width	= GPMC_DEVWIDTH_16BIT,
 	.mux_add_data	= GPMC_MUX_AD,
 };
 
@@ -168,18 +178,12 @@ tusb6010_setup_interface(struct musb_hdrc_platform_data *data,
 		return status;
 	}
 	tusb_resources[0].end = tusb_resources[0].start + 0x9ff;
+	tusb_async.wait_pin = waitpin;
 	async_cs = async;
-	gpmc_cs_write_reg(async, GPMC_CS_CONFIG1,
-			  GPMC_CONFIG1_PAGE_LEN(2)
-			| GPMC_CONFIG1_WAIT_READ_MON
-			| GPMC_CONFIG1_WAIT_WRITE_MON
-			| GPMC_CONFIG1_WAIT_PIN_SEL(waitpin)
-			| GPMC_CONFIG1_READTYPE_ASYNC
-			| GPMC_CONFIG1_WRITETYPE_ASYNC
-			| GPMC_CONFIG1_DEVICESIZE_16
-			| GPMC_CONFIG1_DEVICETYPE_NOR
-			| GPMC_CONFIG1_MUXADDDATA);
 
+	status = gpmc_cs_program_settings(async_cs, &tusb_async);
+	if (status < 0)
+		return status;
 
 	/* SYNC region, primarily for DMA */
 	status = gpmc_cs_request(sync, SZ_16M, (unsigned long *)
@@ -189,21 +193,12 @@ tusb6010_setup_interface(struct musb_hdrc_platform_data *data,
 		return status;
 	}
 	tusb_resources[1].end = tusb_resources[1].start + 0x9ff;
+	tusb_sync.wait_pin = waitpin;
 	sync_cs = sync;
-	gpmc_cs_write_reg(sync, GPMC_CS_CONFIG1,
-			  GPMC_CONFIG1_READMULTIPLE_SUPP
-			| GPMC_CONFIG1_READTYPE_SYNC
-			| GPMC_CONFIG1_WRITEMULTIPLE_SUPP
-			| GPMC_CONFIG1_WRITETYPE_SYNC
-			| GPMC_CONFIG1_PAGE_LEN(2)
-			| GPMC_CONFIG1_WAIT_READ_MON
-			| GPMC_CONFIG1_WAIT_WRITE_MON
-			| GPMC_CONFIG1_WAIT_PIN_SEL(waitpin)
-			| GPMC_CONFIG1_DEVICESIZE_16
-			| GPMC_CONFIG1_DEVICETYPE_NOR
-			| GPMC_CONFIG1_MUXADDDATA
-			/* fclk divider gets set later */
-			);
+
+	status = gpmc_cs_program_settings(sync_cs, &tusb_sync);
+	if (status < 0)
+		return status;
 
 	/* IRQ */
 	status = gpio_request_one(irq, GPIOF_IN, "TUSB6010 irq");
Signature · 1 line
1.7.10.4
author
#9 lore raw

PATCH v4 9/18 ARM: OMAP2+: Don't configure of chip-select options in gpmc_cs_configure()

In reply to Jon Hunter

With the addition of the gpmc_cs_program_settings(), we no longer need or use gpmc_cs_configure() to configure some of the GPMC chip-select options. So rename the function to gpmc_configure() and remove code that modifies options in the CONFIG1 register.

---
 arch/arm/mach-omap2/gpmc-nand.c |    2 +-
 arch/arm/mach-omap2/gpmc.c      |   49 ++++++---------------------------------
 arch/arm/mach-omap2/gpmc.h      |    5 +---
 3 files changed, 9 insertions(+), 47 deletions(-)
arch/arm/mach-omap2/gpmc-nand.c +1 -1
index 75feb95..12e9753 100644
@@ -154,7 +154,7 @@ int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
 		if (err < 0)
 			goto out_free_cs;
 
-		err = gpmc_cs_configure(gpmc_nand_data->cs, GPMC_CONFIG_WP, 0);
+		err = gpmc_configure(GPMC_CONFIG_WP, 0);
 		if (err < 0)
 			goto out_free_cs;
 	}
arch/arm/mach-omap2/gpmc.c +7 -42

70 lines not on this page · raw message

arch/arm/mach-omap2/gpmc.h +1 -4
index ce6ae21..87d2a22 100644
@@ -59,9 +59,6 @@
 #define GPMC_CONFIG1_DEVICETYPE(val)    ((val & 3) << 10)
 #define GPMC_CONFIG1_DEVICETYPE_NOR     GPMC_CONFIG1_DEVICETYPE(0)
 #define GPMC_CONFIG1_MUXTYPE(val)       ((val & 3) << 8)
-#define GPMC_CONFIG1_MUXNONMUX          GPMC_CONFIG1_MUXTYPE(0)
-#define GPMC_CONFIG1_MUXAAD             GPMC_CONFIG1_MUXTYPE(GPMC_MUX_AAD)
-#define GPMC_CONFIG1_MUXADDDATA         GPMC_CONFIG1_MUXTYPE(GPMC_MUX_AD)
 #define GPMC_CONFIG1_TIME_PARA_GRAN     (1 << 4)
 #define GPMC_CONFIG1_FCLK_DIV(val)      (val & 3)
 #define GPMC_CONFIG1_FCLK_DIV2          (GPMC_CONFIG1_FCLK_DIV(1))
@@ -227,6 +224,6 @@ extern int gpmc_cs_request(int cs, unsigned long size, unsigned long *base);
 extern void gpmc_cs_free(int cs);
 extern void omap3_gpmc_save_context(void);
 extern void omap3_gpmc_restore_context(void);
-extern int gpmc_cs_configure(int cs, int cmd, int wval);
+extern int gpmc_configure(int cmd, int wval);
 
 #endif
Signature · 1 line
1.7.10.4
author
#10 lore raw

PATCH v4 10/18 ARM: OMAP2+: Add function to read GPMC settings from device-tree

In reply to Jon Hunter

Adds a function to read the various GPMC chip-select settings from device-tree and store them in the gpmc_settings structure.

Update the GPMC device-tree binding documentation to describe these options.

---
 Documentation/devicetree/bindings/bus/ti-gpmc.txt |   23 ++++++++++++
 arch/arm/mach-omap2/gpmc.c                        |   40 +++++++++++++++++++++
 arch/arm/mach-omap2/gpmc.h                        |    2 ++
 3 files changed, 65 insertions(+)
Documentation/devicetree/bindings/bus/ti-gpmc.txt +23 -0
index 5ddb2e9..6fde1cf 100644
@@ -65,6 +65,29 @@ The following are only applicable to OMAP3+ and AM335x:
  - gpmc,wr-access
  - gpmc,wr-data-mux-bus
 
+GPMC chip-select settings properties for child nodes. All are optional.
+
+- gpmc,burst-length	Page/burst length. Must be 4, 8 or 16.
+- gpmc,burst-wrap	Enables wrap bursting
+- gpmc,burst-read	Enables read page/burst mode
+- gpmc,burst-write	Enables write page/burst mode
+- gpmc,device-nand	Device is NAND
+- gpmc,device-width	Total width of device(s) connected to a GPMC
+			chip-select in bytes. The GPMC supports 8-bit
+			and 16-bit devices and so this property must be
+			1 or 2.
+- gpmc,mux-add-data	Address and data multiplexing configuration.
+			Valid values are 1 for address-address-data
+			multiplexing mode and 2 for address-data
+			multiplexing mode.
+- gpmc,sync-read	Enables synchronous read. Defaults to asynchronous
+			is this is not set.
+- gpmc,sync-write	Enables synchronous writes. Defaults to asynchronous
+			is this is not set.
+- gpmc,wait-pin		Wait-pin used by client. Must be less than
+			"gpmc,num-waitpins".
+- gpmc,wait-on-read	Enables wait monitoring on reads.
+- gpmc,wait-on-write	Enables wait monitoring on writes.
 
 Example for an AM33xx board:
 
arch/arm/mach-omap2/gpmc.c +40 -0
index b22771b..85231b3 100644
@@ -1187,6 +1187,46 @@ static struct of_device_id gpmc_dt_ids[] = {
 };
 MODULE_DEVICE_TABLE(of, gpmc_dt_ids);
 
+/**
+ * gpmc_read_settings_dt - read gpmc settings from device-tree
+ * @np:		pointer to device-tree node for a gpmc child device
+ * @p:		pointer to gpmc settings structure
+ *
+ * Reads the GPMC settings for a GPMC child device from device-tree and
+ * stores them in the GPMC settings structure passed. The GPMC settings
+ * structure is initialised to zero by this function and so any
+ * previously stored settings will be cleared.
+ */
+void gpmc_read_settings_dt(struct device_node *np, struct gpmc_settings *p)
+{
+	memset(p, 0, sizeof(struct gpmc_settings));
+
+	p->sync_read = of_property_read_bool(np, "gpmc,sync-read");
+	p->sync_write = of_property_read_bool(np, "gpmc,sync-write");
+	p->device_nand = of_property_read_bool(np, "gpmc,device-nand");
+	of_property_read_u32(np, "gpmc,device-width", &p->device_width);
+	of_property_read_u32(np, "gpmc,mux-add-data", &p->mux_add_data);
+
+	if (!of_property_read_u32(np, "gpmc,burst-length", &p->burst_len)) {
+		p->burst_wrap = of_property_read_bool(np, "gpmc,burst-wrap");
+		p->burst_read = of_property_read_bool(np, "gpmc,burst-read");
+		p->burst_write = of_property_read_bool(np, "gpmc,burst-write");
+		if (!p->burst_read && !p->burst_write)
+			pr_warn("%s: page/burst-length set but not used!\n",
+				__func__);
+	}
+
+	if (!of_property_read_u32(np, "gpmc,wait-pin", &p->wait_pin)) {
+		p->wait_on_read = of_property_read_bool(np,
+							"gpmc,wait-on-read");
+		p->wait_on_write = of_property_read_bool(np,
+							 "gpmc,wait-on-write");
+		if (!p->wait_on_read && !p->wait_on_write)
+			pr_warn("%s: read/write wait monitoring not enabled!\n",
+				__func__);
+	}
+}
+
 static void __maybe_unused gpmc_read_timings_dt(struct device_node *np,
 						struct gpmc_timings *gpmc_t)
 {
arch/arm/mach-omap2/gpmc.h +2 -0
index 87d2a22..707f6d5 100644
@@ -225,5 +225,7 @@ extern void gpmc_cs_free(int cs);
 extern void omap3_gpmc_save_context(void);
 extern void omap3_gpmc_restore_context(void);
 extern int gpmc_configure(int cmd, int wval);
+extern void gpmc_read_settings_dt(struct device_node *np,
+				  struct gpmc_settings *p);
 
 #endif
Signature · 1 line
1.7.10.4
#11 lore raw

PATCH v4 10/18 ARM: OMAP2+: Add function to read GPMC settings from device-tree

Quoted 23 lines · Jon Hunter

Adds a function to read the various GPMC chip-select settings from device-tree and store them in the gpmc_settings structure.

Update the GPMC device-tree binding documentation to describe these options.

---
 Documentation/devicetree/bindings/bus/ti-gpmc.txt |   23 ++++++++++++
 arch/arm/mach-omap2/gpmc.c                        |   40 +++++++++++++++++++++
 arch/arm/mach-omap2/gpmc.h                        |    2 ++
 3 files changed, 65 insertions(+)
Documentation/devicetree/bindings/bus/ti-gpmc.txt +1 -0
index 5ddb2e9..6fde1cf 100644
@@ -65,6 +65,29 @@ The following are only applicable to OMAP3+ and AM335x:
  - gpmc,wr-access
  - gpmc,wr-data-mux-bus
 
+GPMC chip-select settings properties for child nodes. All are optional.

Documentation/devicetree/bindings/bus/ti-gpmc.txt The following are only applicable to OMAP3+ and AM335x: · line 78

Quoted 10 lines
Documentation/devicetree/bindings/bus/ti-gpmc.txt +10 -0
+
+- gpmc,burst-length	Page/burst length. Must be 4, 8 or 16.
+- gpmc,burst-wrap	Enables wrap bursting
+- gpmc,burst-read	Enables read page/burst mode
+- gpmc,burst-write	Enables write page/burst mode
+- gpmc,device-nand	Device is NAND
+- gpmc,device-width	Total width of device(s) connected to a GPMC
+			chip-select in bytes. The GPMC supports 8-bit
+			and 16-bit devices and so this property must be
+			1 or 2.

I would suggest specifying the actual number of bits. ie. 8 or 16. There is some precidence for that already in DT bindings.

Documentation/devicetree/bindings/bus/ti-gpmc.txt The following are only applicable to OMAP3+ and AM335x: · line 84

Quoted 6 lines
Documentation/devicetree/bindings/bus/ti-gpmc.txt +6 -0
+- gpmc,mux-add-data	Address and data multiplexing configuration.
+			Valid values are 1 for address-address-data
+			multiplexing mode and 2 for address-data
+			multiplexing mode.
+- gpmc,sync-read	Enables synchronous read. Defaults to asynchronous
+			is this is not set.

'if'?

Documentation/devicetree/bindings/bus/ti-gpmc.txt The following are only applicable to OMAP3+ and AM335x: · line 90

Quoted 6 lines
Documentation/devicetree/bindings/bus/ti-gpmc.txt +6 -0
+- gpmc,sync-write	Enables synchronous writes. Defaults to asynchronous
+			is this is not set.
+- gpmc,wait-pin		Wait-pin used by client. Must be less than
+			"gpmc,num-waitpins".
+- gpmc,wait-on-read	Enables wait monitoring on reads.
+- gpmc,wait-on-write	Enables wait monitoring on writes.

Otherwise looks okay to me.

g.

author
#12 lore raw

PATCH v4 10/18 ARM: OMAP2+: Add function to read GPMC settings from device-tree

Quoted 23 lines · Grant Likely
Quoted 22 lines · Jon Hunter

Adds a function to read the various GPMC chip-select settings from device-tree and store them in the gpmc_settings structure.

Update the GPMC device-tree binding documentation to describe these options.

---
 Documentation/devicetree/bindings/bus/ti-gpmc.txt |   23 ++++++++++++
 arch/arm/mach-omap2/gpmc.c                        |   40 +++++++++++++++++++++
 arch/arm/mach-omap2/gpmc.h                        |    2 ++
 3 files changed, 65 insertions(+)
Documentation/devicetree/bindings/bus/ti-gpmc.txt +0 -0
index 5ddb2e9..6fde1cf 100644
@@ -65,6 +65,29 @@ The following are only applicable to OMAP3+ and AM335x:
  - gpmc,wr-access
  - gpmc,wr-data-mux-bus
 
Quoted 14 lines

Documentation/devicetree/bindings/bus/ti-gpmc.txt The following are only applicable to OMAP3+ and AM335x: · line 78

Quoted 11 lines
Documentation/devicetree/bindings/bus/ti-gpmc.txt +11 -0
+GPMC chip-select settings properties for child nodes. All are optional.
+
+- gpmc,burst-length	Page/burst length. Must be 4, 8 or 16.
+- gpmc,burst-wrap	Enables wrap bursting
+- gpmc,burst-read	Enables read page/burst mode
+- gpmc,burst-write	Enables write page/burst mode
+- gpmc,device-nand	Device is NAND
+- gpmc,device-width	Total width of device(s) connected to a GPMC
+			chip-select in bytes. The GPMC supports 8-bit
+			and 16-bit devices and so this property must be
+			1 or 2.

I would suggest specifying the actual number of bits. ie. 8 or 16. There is some precidence for that already in DT bindings.

I used bytes and not bits here as it was more convenient for programming a register bit field. However, it would be equally easy to shift the value and program the register if we use bits. So this can be changed.

By the way, I have seen some of the flash bindings (eg. mtd-physmap.txt) use bytes and not bits, however, I do see others use bits (nand.txt). However, if the preference is for bits then we can conform to that.

Tony has this queued for v3.10 now. However, we can fix this up if you feel strongly about this.

Quoted 9 lines

Documentation/devicetree/bindings/bus/ti-gpmc.txt The following are only applicable to OMAP3+ and AM335x: · line 84

Quoted 6 lines
Documentation/devicetree/bindings/bus/ti-gpmc.txt +6 -0
+- gpmc,mux-add-data	Address and data multiplexing configuration.
+			Valid values are 1 for address-address-data
+			multiplexing mode and 2 for address-data
+			multiplexing mode.
+- gpmc,sync-read	Enables synchronous read. Defaults to asynchronous
+			is this is not set.

'if'?

Quoted 8 lines

Documentation/devicetree/bindings/bus/ti-gpmc.txt The following are only applicable to OMAP3+ and AM335x: · line 90

Quoted 6 lines
Documentation/devicetree/bindings/bus/ti-gpmc.txt +6 -0
+- gpmc,sync-write	Enables synchronous writes. Defaults to asynchronous
+			is this is not set.
+- gpmc,wait-pin		Wait-pin used by client. Must be less than
+			"gpmc,num-waitpins".
+- gpmc,wait-on-read	Enables wait monitoring on reads.
+- gpmc,wait-on-write	Enables wait monitoring on writes.

Otherwise looks okay to me.

Thanks
Jon

author
#13 lore raw

PATCH v4 11/18 ARM: OMAP2+: Add additional GPMC timing parameters

In reply to Jon Hunter

Some of the GPMC timings parameters are currently missing from the GPMC device-tree binding. Add these parameters to the binding documentation as well as code to read them. Also add either "-ps" or "-ns" suffix to the GPMC timing properties to indicate whether the timing is in picoseconds or nanoseconds.

The existing code in gpmc_read_timings_dt() is checking the value of of_property_read_u32() and only is successful storing the value read in the gpmc_timings structure. Checking the return value in this case is not necessary and we can simply read the value, if present, and store directly in the gpmc_timings structure. Therefore, simplify the code by removing these checks.

The comment in the gpmc_read_timings_dt() function, "only for OMAP3430" is also incorrect as it is applicable to all OMAP3+ devices. So correct this too.

---
 Documentation/devicetree/bindings/bus/ti-gpmc.txt |   78 +++++++++++------
 arch/arm/mach-omap2/gpmc.c                        |   94 ++++++++++-----------
 2 files changed, 98 insertions(+), 74 deletions(-)
Documentation/devicetree/bindings/bus/ti-gpmc.txt +51 -27
index 6fde1cf..4b87ea1 100644
@@ -35,35 +35,59 @@ Required properties:
 
 Timing properties for child nodes. All are optional and default to 0.
 
- - gpmc,sync-clk:	Minimum clock period for synchronous mode, in picoseconds
-
- Chip-select signal timings corresponding to GPMC_CONFIG2:
- - gpmc,cs-on:		Assertion time
- - gpmc,cs-rd-off:	Read deassertion time
- - gpmc,cs-wr-off:	Write deassertion time
-
- ADV signal timings corresponding to GPMC_CONFIG3:
- - gpmc,adv-on:		Assertion time
- - gpmc,adv-rd-off:	Read deassertion time
- - gpmc,adv-wr-off:	Write deassertion time
-
- WE signals timings corresponding to GPMC_CONFIG4:
- - gpmc,we-on:		Assertion time
- - gpmc,we-off:		Deassertion time
-
- OE signals timings corresponding to GPMC_CONFIG4:
- - gpmc,oe-on:		Assertion time
- - gpmc,oe-off:		Deassertion time
-
- Access time and cycle time timings corresponding to GPMC_CONFIG5:
- - gpmc,page-burst-access: Multiple access word delay
- - gpmc,access:		Start-cycle to first data valid delay
- - gpmc,rd-cycle:	Total read cycle time
- - gpmc,wr-cycle:	Total write cycle time
+ - gpmc,sync-clk-ps:	Minimum clock period for synchronous mode, in picoseconds
+
+ Chip-select signal timings (in nanoseconds) corresponding to GPMC_CONFIG2:
+ - gpmc,cs-on-ns:	Assertion time
+ - gpmc,cs-rd-off-ns:	Read deassertion time
+ - gpmc,cs-wr-off-ns:	Write deassertion time
+
+ ADV signal timings (in nanoseconds) corresponding to GPMC_CONFIG3:
+ - gpmc,adv-on-ns:	Assertion time
+ - gpmc,adv-rd-off-ns:	Read deassertion time
+ - gpmc,adv-wr-off-ns:	Write deassertion time
+
+ WE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
+ - gpmc,we-on-ns	Assertion time
+ - gpmc,we-off-ns:	Deassertion time
+
+ OE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
+ - gpmc,oe-on-ns:	Assertion time
+ - gpmc,oe-off-ns:	Deassertion time
+
+ Access time and cycle time timings (in nanoseconds) corresponding to
+ GPMC_CONFIG5:
+ - gpmc,page-burst-access-ns: 	Multiple access word delay
+ - gpmc,access-ns:		Start-cycle to first data valid delay
+ - gpmc,rd-cycle-ns:		Total read cycle time
+ - gpmc,wr-cycle-ns:		Total write cycle time
+ - gpmc,bus-turnaround-ns:	Turn-around time between successive accesses
+ - gpmc,cycle2cycle-delay-ns:	Delay between chip-select pulses
+ - gpmc,clk-activation-ns: 	GPMC clock activation time
+ - gpmc,wait-monitoring-ns:	Start of wait monitoring with regard to valid
+				data
+
+Boolean timing parameters. If property is present parameter enabled and
+disabled if omitted:
+ - gpmc,adv-extra-delay:	ADV signal is delayed by half GPMC clock
+ - gpmc,cs-extra-delay:		CS signal is delayed by half GPMC clock
+ - gpmc,cycle2cycle-diffcsen:	Add "cycle2cycle-delay" between successive
+				accesses to a different CS
+ - gpmc,cycle2cycle-samecsen:	Add "cycle2cycle-delay" between successive
+				accesses to the same CS
+ - gpmc,oe-extra-delay:		OE signal is delayed by half GPMC clock
+ - gpmc,we-extra-delay:		WE signal is delayed by half GPMC clock
+ - gpmc,time-para-granularity:	Multiply all access times by 2
 
 The following are only applicable to OMAP3+ and AM335x:
- - gpmc,wr-access
- - gpmc,wr-data-mux-bus
+ - gpmc,wr-access-ns:		In synchronous write mode, for single or
+				burst accesses, defines the number of
+				GPMC_FCLK cycles from start access time
+				to the GPMC_CLK rising edge used by the
+				memory device for the first data capture.
+ - gpmc,wr-data-mux-bus-ns:	In address-data multiplex mode, specifies
+				the time when the first data is driven on
+				the address-data bus.
 
 GPMC chip-select settings properties for child nodes. All are optional.
 
arch/arm/mach-omap2/gpmc.c +47 -47

114 lines not on this page · raw message

Signature · 1 line
1.7.10.4
author
#14 lore raw

PATCH v4 12/18 ARM: OMAP2+: Add device-tree support for NOR flash

In reply to Jon Hunter

NOR flash is not currently supported when booting with device-tree on OMAP2+ devices. Add support to detect and configure NOR devices when booting with device-tree.

Add documentation for the TI GPMC NOR binding.

---
 Documentation/devicetree/bindings/mtd/gpmc-nor.txt |   98 +++++++++++++++++
 arch/arm/mach-omap2/gpmc.c                         |  115 ++++++++++++++++++++
 2 files changed, 213 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/gpmc-nor.txt
Documentation/devicetree/bindings/mtd/gpmc-nor.txt new file +98 -0
new file mode 100644
index 0000000..420b3ab
@@ -0,0 +1,98 @@
+Device tree bindings for NOR flash connect to TI GPMC
+
+NOR flash connected to the TI GPMC (found on OMAP boards) are represented as
+child nodes of the GPMC controller with a name of "nor".
+
+All timing relevant properties as well as generic GPMC child properties are
+explained in a separate documents. Please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+Required properties:
+- bank-width: 		Width of NOR flash in bytes. GPMC supports 8-bit and
+			16-bit devices and so must be either 1 or 2 bytes.
+- compatible:		Documentation/devicetree/bindings/mtd/mtd-physmap.txt
+- gpmc,cs-on-ns:		Chip-select assertion time
+- gpmc,cs-rd-off-ns:	Chip-select de-assertion time for reads
+- gpmc,cs-wr-off-ns:	Chip-select de-assertion time for writes
+- gpmc,oe-on-ns:	Output-enable assertion time
+- gpmc,oe-off-ns:	Output-enable de-assertion time
+- gpmc,we-on-ns		Write-enable assertion time
+- gpmc,we-off-ns:	Write-enable de-assertion time
+- gpmc,access-ns:	Start cycle to first data capture (read access)
+- gpmc,rd-cycle-ns:	Total read cycle time
+- gpmc,wr-cycle-ns:	Total write cycle time
+- linux,mtd-name:	Documentation/devicetree/bindings/mtd/mtd-physmap.txt
+- reg:			Chip-select, base address (relative to chip-select)
+			and size of NOR flash. Note that base address will be
+			typically 0 as this is the start of the chip-select.
+
+Optional properties:
+- gpmc,XXX		Additional GPMC timings and settings parameters. See
+			Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+Optional properties for partiton table parsing:
+- #address-cells: should be set to 1
+- #size-cells: should be set to 1
+
+Example:
+
+gpmc: gpmc at 6e000000 {
+	compatible = "ti,omap3430-gpmc", "simple-bus";
+	ti,hwmods = "gpmc";
+	reg = <0x6e000000 0x1000>;
+	interrupts = <20>;
+	gpmc,num-cs = <8>;
+	gpmc,num-waitpins = <4>;
+	#address-cells = <2>;
+	#size-cells = <1>;
+
+	ranges = <0 0 0x10000000 0x08000000>;
+
+	nor at 0,0 {
+		compatible = "cfi-flash";
+		linux,mtd-name= "intel,pf48f6000m0y1be";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0 0 0x08000000>;
+		bank-width = <2>;
+
+		gpmc,mux-add-data;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <186>;
+		gpmc,cs-wr-off-ns = <186>;
+		gpmc,adv-on-ns = <12>;
+		gpmc,adv-rd-off-ns = <48>;
+		gpmc,adv-wr-off-ns = <48>;
+		gpmc,oe-on-ns = <54>;
+		gpmc,oe-off-ns = <168>;
+		gpmc,we-on-ns = <54>;
+		gpmc,we-off-ns = <168>;
+		gpmc,rd-cycle-ns = <186>;
+		gpmc,wr-cycle-ns = <186>;
+		gpmc,access-ns = <114>;
+		gpmc,page-burst-access-ns = <6>;
+		gpmc,bus-turnaround-ns = <12>;
+		gpmc,cycle2cycle-delay-ns = <18>;
+		gpmc,wr-data-mux-bus-ns = <90>;
+		gpmc,wr-access-ns = <186>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+
+		partition at 0 {
+			label = "bootloader-nor";
+			reg = <0 0x40000>;
+		};
+		partition at 0x40000 {
+			label = "params-nor";
+			reg = <0x40000 0x40000>;
+		};
+		partition at 0x80000 {
+			label = "kernel-nor";
+			reg = <0x80000 0x200000>;
+		};
+		partition at 0x280000 {
+			label = "filesystem-nor";
+			reg = <0x240000 0x7d80000>;
+		};
+	};
+};
arch/arm/mach-omap2/gpmc.c +115 -0

139 lines not on this page · raw message

Signature · 1 line
1.7.10.4
author
#15 lore raw

PATCH v4 13/18 ARM: OMAP2+: Convert NAND to retrieve GPMC settings from DT

In reply to Jon Hunter

When booting with device-tree, retrieve GPMC settings for NAND from the device-tree blob. This will allow us to remove all static settings stored in the gpmc-nand.c in the future once the migration to device-tree is complete.

---
 arch/arm/mach-omap2/gpmc-nand.c |   16 ++++++++++------
 1 file changed, 10 insertions(+), 6 deletions(-)
arch/arm/mach-omap2/gpmc-nand.c +10 -6
index 12e9753..d9c2719 100644
@@ -137,12 +137,16 @@ int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
 			return err;
 		}
 
-		s.device_nand = true;
-
-		/* Enable RD PIN Monitoring Reg */
-		if (gpmc_nand_data->dev_ready) {
-			s.wait_on_read = true;
-			s.wait_on_write = true;
+		if (gpmc_nand_data->of_node) {
+			gpmc_read_settings_dt(gpmc_nand_data->of_node, &s);
+		} else {
+			s.device_nand = true;
+
+			/* Enable RD PIN Monitoring Reg */
+			if (gpmc_nand_data->dev_ready) {
+				s.wait_on_read = true;
+				s.wait_on_write = true;
+			}
 		}
 
 		if (gpmc_nand_data->devsize == NAND_BUSWIDTH_16)
Signature · 1 line
1.7.10.4
author
#16 lore raw

PATCH v4 14/18 ARM: OMAP2+: Convert ONENAND to retrieve GPMC settings from DT

In reply to Jon Hunter

When booting with device-tree, retrieve GPMC settings for ONENAND from the device-tree blob. This will allow us to remove all static settings stored in the gpmc-nand.c in the future once the migration to device-tree is complete.

The user must now specify the ONENAND device width in the device-tree binding so that the GPMC can be programmed correctly. Therefore, update the device-tree binding documentation for ONENAND devices connected to the GPMC to reflect this.

Please note that this does not include GPMC timings for ONENAND. The timings are being calculated at runtime.

There is some legacy code that only enables read wait monitoring for non-OMAP3 devices. There are no known OMAP3 device issues that prevent this feature being enabled and so when booting with device-tree use the wait-monitoring settings described in the device-tree blob.

---
 .../devicetree/bindings/mtd/gpmc-onenand.txt       |    3 +++
 arch/arm/mach-omap2/gpmc-onenand.c                 |   21 ++++++++++++++------
 2 files changed, 18 insertions(+), 6 deletions(-)
Documentation/devicetree/bindings/mtd/gpmc-onenand.txt +3 -0
index deec9da..b752942 100644
@@ -10,6 +10,8 @@ Documentation/devicetree/bindings/bus/ti-gpmc.txt
 Required properties:
 
  - reg:			The CS line the peripheral is connected to
+ - gpmc,device-width	Width of the ONENAND device connected to the GPMC
+			in bytes. Must be 1 or 2.
 
 Optional properties:
 
@@ -34,6 +36,7 @@ Example for an OMAP3430 board:
 
 		onenand at 0 {
 			reg = <0 0 0>; /* CS0, offset 0 */
+			gpmc,device-width = <2>;
 
 			#address-cells = <1>;
 			#size-cells = <1>;
arch/arm/mach-omap2/gpmc-onenand.c +15 -6
index 46aac83..64b5a83 100644
@@ -272,6 +272,10 @@ static int omap2_onenand_setup_async(void __iomem *onenand_base)
 	struct gpmc_timings t;
 	int ret;
 
+	if (gpmc_onenand_data->of_node)
+		gpmc_read_settings_dt(gpmc_onenand_data->of_node,
+				      &onenand_async);
+
 	omap2_onenand_set_async_mode(onenand_base);
 
 	omap2_onenand_calc_async_timings(&t);
@@ -300,12 +304,17 @@ static int omap2_onenand_setup_sync(void __iomem *onenand_base, int *freq_ptr)
 		set_onenand_cfg(onenand_base);
 	}
 
-	/*
-	 * FIXME: Appears to be legacy code from initial ONENAND commit.
-	 * Unclear what boards this is for and if this can be removed.
-	 */
-	if (!cpu_is_omap34xx())
-		onenand_sync.wait_on_read = true;
+	if (gpmc_onenand_data->of_node) {
+		gpmc_read_settings_dt(gpmc_onenand_data->of_node,
+				      &onenand_sync);
+	} else {
+		/*
+		 * FIXME: Appears to be legacy code from initial ONENAND commit.
+		 * Unclear what boards this is for and if this can be removed.
+		 */
+		if (!cpu_is_omap34xx())
+			onenand_sync.wait_on_read = true;
+	}
 
 	omap2_onenand_calc_sync_timings(&t, gpmc_onenand_data->flags, freq);
 
Signature · 1 line
1.7.10.4
author
#17 lore raw

PATCH v4 15/18 ARM: OMAP2+: Detect incorrectly aligned GPMC base address

In reply to Jon Hunter

Each GPMC chip-select can be configured to map 16MB, 32MB, 64MB or 128MB of address space. The physical base address where a chip-select starts is also configurable and must be aligned on a boundary that is equal to or greater than the size of the address space mapped bt the chip-select. When enabling a GPMC chip-select, ensure that the base address is aligned to the appropriate boundary.

---
 arch/arm/mach-omap2/gpmc.c |   22 +++++++++++++++++++---
 1 file changed, 19 insertions(+), 3 deletions(-)
arch/arm/mach-omap2/gpmc.c +19 -3
index 94624bf..9797f46 100644
@@ -403,11 +403,18 @@ int gpmc_cs_set_timings(int cs, const struct gpmc_timings *t)
 	return 0;
 }
 
-static void gpmc_cs_enable_mem(int cs, u32 base, u32 size)
+static int gpmc_cs_enable_mem(int cs, u32 base, u32 size)
 {
 	u32 l;
 	u32 mask;
 
+	/*
+	 * Ensure that base address is aligned on a
+	 * boundary equal to or greater than size.
+	 */
+	if (base & (size - 1))
+		return -EINVAL;
+
 	mask = (1 << GPMC_SECTION_SHIFT) - size;
 	l = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7);
 	l &= ~0x3f;
@@ -416,6 +423,8 @@ static void gpmc_cs_enable_mem(int cs, u32 base, u32 size)
 	l |= ((mask >> GPMC_CHUNK_SHIFT) & 0x0f) << 8;
 	l |= GPMC_CONFIG7_CSVALID;
 	gpmc_cs_write_reg(cs, GPMC_CS_CONFIG7, l);
+
+	return 0;
 }
 
 static void gpmc_cs_disable_mem(int cs)
@@ -526,7 +535,9 @@ static int gpmc_cs_remap(int cs, u32 base)
 	ret = gpmc_cs_insert_mem(cs, base, size);
 	if (ret < 0)
 		return ret;
-	gpmc_cs_enable_mem(cs, base, size);
+	ret = gpmc_cs_enable_mem(cs, base, size);
+	if (ret < 0)
+		return ret;
 
 	return 0;
 }
@@ -556,7 +567,12 @@ int gpmc_cs_request(int cs, unsigned long size, unsigned long *base)
 	if (r < 0)
 		goto out;
 
-	gpmc_cs_enable_mem(cs, res->start, resource_size(res));
+	r = gpmc_cs_enable_mem(cs, res->start, resource_size(res));
+	if (r < 0) {
+		release_resource(res);
+		goto out;
+	}
+
 	*base = res->start;
 	gpmc_cs_set_reserved(cs, 1);
 out:
Signature · 1 line
1.7.10.4
author
#18 lore raw

PATCH v4 16/18 ARM: OMAP2+: Remove unnecesssary GPMC definitions and variable

In reply to Jon Hunter

With commit 21cc2bd (ARM: OMAP2+: Remove apollon board support) the variable "boot_rom_space" is now not needed and the code surrounding this variable can be cleaned up and simplified. Remove unnecessary definitions and clean-up the comment as well.

---
 arch/arm/mach-omap2/gpmc.c |   12 +++++-------
 1 file changed, 5 insertions(+), 7 deletions(-)
arch/arm/mach-omap2/gpmc.c +5 -7
index 9797f46..ebb88cf 100644
@@ -92,9 +92,7 @@
 #define GPMC_CS_SIZE		0x30
 #define	GPMC_BCH_SIZE		0x10
 
-#define GPMC_MEM_START		0x00000000
 #define GPMC_MEM_END		0x3FFFFFFF
-#define BOOT_ROM_SPACE		0x100000	/* 1MB */
 
 #define GPMC_CHUNK_SHIFT	24		/* 16 MB */
 #define GPMC_SECTION_SHIFT	28		/* 128 MB */
@@ -790,13 +788,13 @@ static void gpmc_mem_exit(void)
 static int gpmc_mem_init(void)
 {
 	int cs, rc;
-	unsigned long boot_rom_space = 0;
 
-	/* never allocate the first page, to facilitate bug detection;
-	 * even if we didn't boot from ROM.
+	/*
+	 * The first 1MB of GPMC address space is typically mapped to
+	 * the internal ROM. Never allocate the first page, to
+	 * facilitate bug detection; even if we didn't boot from ROM.
 	 */
-	boot_rom_space = BOOT_ROM_SPACE;
-	gpmc_mem_root.start = GPMC_MEM_START + boot_rom_space;
+	gpmc_mem_root.start = SZ_1M;
 	gpmc_mem_root.end = GPMC_MEM_END;
 
 	/* Reserve all regions that has been set up by bootloader */
Signature · 1 line
1.7.10.4
author
#19 lore raw

PATCH v4 17/18 ARM: OMAP2+: Allow GPMC probe to complete even if CS mapping fails

In reply to Jon Hunter

When the GPMC driver is probed, we call gpmc_mem_init() to see which chip-selects have already been configured and enabled by the boot-loader and allocate space for them. If we fail to allocate space for one chip-select, then we return failure from the probe and the GPMC driver will not be available.

Rather than render the GPMC useless for all GPMC devices, if we fail to allocate space for one chip-select print a warning and disable the chip-select. This way other GPMC clients can still be used.

There is no downside to this approach, because all GPMC clients need to request a chip-select before they can use the GPMC and on requesting a chip-select, if memory has not already been reserved for the chip-select then it will be.

---
 arch/arm/mach-omap2/gpmc.c |   24 +++++++-----------------
 1 file changed, 7 insertions(+), 17 deletions(-)
arch/arm/mach-omap2/gpmc.c +7 -17
index ebb88cf..9208d8e 100644
@@ -785,9 +785,9 @@ static void gpmc_mem_exit(void)
 
 }
 
-static int gpmc_mem_init(void)
+static void gpmc_mem_init(void)
 {
-	int cs, rc;
+	int cs;
 
 	/*
 	 * The first 1MB of GPMC address space is typically mapped to
@@ -804,16 +804,12 @@ static int gpmc_mem_init(void)
 		if (!gpmc_cs_mem_enabled(cs))
 			continue;
 		gpmc_cs_get_memconf(cs, &base, &size);
-		rc = gpmc_cs_insert_mem(cs, base, size);
-		if (rc < 0) {
-			while (--cs >= 0)
-				if (gpmc_cs_mem_enabled(cs))
-					gpmc_cs_delete_mem(cs);
-			return rc;
+		if (gpmc_cs_insert_mem(cs, base, size)) {
+			pr_warn("%s: disabling cs %d mapped at 0x%x-0x%x\n",
+				__func__, cs, base, base + size);
+			gpmc_cs_disable_mem(cs);
 		}
 	}
-
-	return 0;
 }
 
 static u32 gpmc_round_ps_to_sync_clk(u32 time_ps, u32 sync_clk)
@@ -1611,13 +1607,7 @@ static int gpmc_probe(struct platform_device *pdev)
 	dev_info(gpmc_dev, "GPMC revision %d.%d\n", GPMC_REVISION_MAJOR(l),
 		 GPMC_REVISION_MINOR(l));
 
-	rc = gpmc_mem_init();
-	if (rc < 0) {
-		clk_disable_unprepare(gpmc_l3_clk);
-		clk_put(gpmc_l3_clk);
-		dev_err(gpmc_dev, "failed to reserve memory\n");
-		return rc;
-	}
+	gpmc_mem_init();
 
 	if (gpmc_setup_irq() < 0)
 		dev_warn(gpmc_dev, "gpmc_setup_irq failed\n");
Signature · 1 line
1.7.10.4
author
#20 lore raw

PATCH v4 18/18 ARM: OMAP2+: return -ENODEV if GPMC child device creation fails

In reply to Jon Hunter

From: Javier Martinez Canillas <[email protected]>

gpmc_probe_nor_child() calls of_platform_device_create() to create a platform device for the NOR child. If this function fails the value of ret is returned to the caller but this value is zero since it was assigned the return of a previous call to gpmc_cs_program_settings() that had to succeed or otherwise gpmc_probe_nor_child() would have returned before.

This means that if of_platform_device_create() fails, 0 will be returned to the caller instead of an appropriate error code.

---
 arch/arm/mach-omap2/gpmc.c |    1 +
 1 file changed, 1 insertion(+)
arch/arm/mach-omap2/gpmc.c +1 -0
index 9208d8e..615da97 100644
@@ -1495,6 +1495,7 @@ static int gpmc_probe_nor_child(struct platform_device *pdev,
 		return 0;
 
 	dev_err(&pdev->dev, "failed to create gpmc child %s\n", child->name);
+	ret = -ENODEV;
 
 err:
 	gpmc_cs_free(cs);
Signature · 1 line
1.7.10.4