ARM: tegra: add platform suspend support
Subsystems (5)
v4 cover ARM: tegra: add platform suspend support
This series introduces a basic functionality for Tegra to support the platform suspend and resume.
Note: This series only adds the support for Tegra20 and Tegra30. The Tegra114 will be supported later.
This series needs the patch below that not yet be merged into linux-mmc tree to make the system suspend/resume function work correctly.
"mmc: tegra: use mmc_of_parse to get the support of standard MMC DT bindings"
Verified on Seaboard and Cardhu.
V4:
* add tegra_pm_validate_suspend_mode() to validate the suspend mode config from DT
* squash the patch below into [4/9] to avoid churn after this series [2/3] ARM: tegra: refactor the pmc_pm_set function
V3:
* fix the PMC DT configurations for paz00 board
* add a protection for only support LP2 suspend mode
V2:
* re-order the patch sequence to make sure the suspend function can be enabled well after the last patch be merged
* squash the patches that defined the PM bindings for PMC and the implementation
Joseph Lo (9):
gpio: tegra: add gpio wakeup source handling
ARM: tegra: irq: add wake up handling
ARM: dt: tegra: add bindings of power management configurations for
PMC
ARM: tegra: pm: add platform suspend support
ARM: dts: tegra: add power gpio keys to DT
ARM: dts: tegra: whistler: add wakeup source for KBC
ARM: dts: tegra: add non-removable and keep-power-in-suspend property
for MMC
ARM: tegra: config: defconfig update
ARM: dts: tegra: add the PM configurations of PMC
.../bindings/arm/tegra/nvidia,tegra20-pmc.txt | 42 ++++++- arch/arm/boot/dts/tegra20-harmony.dts | 17 +++ arch/arm/boot/dts/tegra20-paz00.dts | 7 ++ arch/arm/boot/dts/tegra20-seaboard.dts | 8 ++ arch/arm/boot/dts/tegra20-trimslice.dts | 20 +++ arch/arm/boot/dts/tegra20-ventana.dts | 19 +++ arch/arm/boot/dts/tegra20-whistler.dts | 10 ++ arch/arm/boot/dts/tegra30-beaver.dts | 8 ++ arch/arm/boot/dts/tegra30-cardhu-a02.dts | 1 + arch/arm/boot/dts/tegra30-cardhu-a04.dts | 1 + arch/arm/boot/dts/tegra30-cardhu.dtsi | 8 ++ arch/arm/configs/tegra_defconfig | 1 + arch/arm/mach-tegra/common.c | 3 + arch/arm/mach-tegra/irq.c | 95 ++++++++++++++- arch/arm/mach-tegra/irq.h | 6 + arch/arm/mach-tegra/pm.c | 93 ++++++++++++-- arch/arm/mach-tegra/pm.h | 15 +++ arch/arm/mach-tegra/pmc.c | 135 ++++++++++++++++++++- arch/arm/mach-tegra/pmc.h | 12 +- drivers/gpio/gpio-tegra.c | 21 +++- 20 files changed, 500 insertions(+), 22 deletions(-)
Signature · 1 line
1.8.1.5
PATCH v4 1/9 gpio: tegra: add gpio wakeup source handling
This patch add the gpio wakeup source handling for the Tegra platform. It was be done by enabling the irq for the gpio in the gpio controller and enabling the bank irq of the gpio in the Tegra legacy irq controller when the system going to suspend.
Based on the work by:
Varun Wadekar <[email protected]>
---
V4:
* no change
V3:
* no change
V2:
* no change
--- drivers/gpio/gpio-tegra.c | 21 +++++++++++++++++++-- 1 file changed, 19 insertions(+), 2 deletions(-)
drivers/gpio/gpio-tegra.c +19 -2
@@ -72,6 +72,7 @@ struct tegra_gpio_bank {u32 oe[4 ];u32 int_enb[4 ];u32 int_lvl[4 ]; +u32 wake_enb[4 ];#endif };
@@ -333,15 +334,31 @@ static int tegra_gpio_suspend(struct device *dev) bank->oe[p] =tegra_gpio_readl (GPIO_OE (gpio)); bank->int_enb[p] =tegra_gpio_readl (GPIO_INT_ENB (gpio)); bank->int_lvl[p] =tegra_gpio_readl (GPIO_INT_LVL (gpio)); + +/* Enable gpio irq for wake up source */ +tegra_gpio_writel (bank->wake_enb[p], + GPIO_INT_ENB(gpio)); } }local_irq_restore (flags);return 0 ; } -static int tegra_gpio_wake_enable (struct irq_data *d,unsigned int enable) +static int tegra_gpio_irq_set_wake (struct irq_data *d,unsigned int enable) {struct tegra_gpio_bank *bank =irq_data_get_irq_chip_data (d); +int gpio = d->hwirq; +u32 port, bit, mask; + + port =GPIO_PORT (gpio); + bit =GPIO_BIT (gpio); + mask =BIT (bit); + +if (enable) + bank->wake_enb[port] |= mask; +else + bank->wake_enb[port] &= ~mask; +return irq_set_irq_wake (bank->irq, enable); }#endif
@@ -353,7 +370,7 @@ static struct irq_chip tegra_gpio_irq_chip = { .irq_unmask = tegra_gpio_irq_unmask, .irq_set_type = tegra_gpio_irq_set_type, #ifdef CONFIG_PM_SLEEP - .irq_set_wake = tegra_gpio_wake_enable, + .irq_set_wake = tegra_gpio_irq_set_wake,#endif };
Signature · 1 line
1.8.1.5
PATCH v4 1/9 gpio: tegra: add gpio wakeup source handling
Quoted 4 lines · Joseph Lo
This patch add the gpio wakeup source handling for the Tegra platform. It was be done by enabling the irq for the gpio in the gpio controller and enabling the bank irq of the gpio in the Tegra legacy irq controller when the system going to suspend.
Grant, Linus, are you OK with this change? Could I please get an Ack to take it through the Tegra tree? Thanks.
PATCH v4 2/9 ARM: tegra: irq: add wake up handling
In reply to Joseph LoAdd the wake up handling for legacy irq controller, and using IRQCHIP_MASK_ON_SUSPEND for wake irq handling.
Based on the work by:
Varun Wadekar <[email protected]>
---
V4:
* no change
V3:
* no change
V2:
* no change
--- arch/arm/mach-tegra/common.c | 2 + arch/arm/mach-tegra/irq.c | 95 +++++++++++++++++++++++++++++++++++++++++++- arch/arm/mach-tegra/irq.h | 6 +++ 3 files changed, 102 insertions(+), 1 deletion(-)
arch/arm/mach-tegra/common.c +2 -0
@@ -33,6 +33,7 @@#include "common.h" #include "fuse.h" #include "iomap.h" +#include "irq.h" #include "pmc.h" #include "apbio.h" #include "sleep.h"
@@ -64,6 +65,7 @@ void __init tegra_dt_init_irq(void)tegra_pmc_init ();tegra_init_irq ();irqchip_init (); + tegra_legacy_irq_syscore_init(); }#endif
arch/arm/mach-tegra/irq.c +94 -1
131 lines not on this page · raw message
arch/arm/mach-tegra/irq.h +6 -0
@@ -19,4 +19,10 @@bool tegra_pending_sgi (void ); +#ifdef CONFIG_PM_SLEEP +int tegra_legacy_irq_syscore_init (void ); +#else +static inline int tegra_legacy_irq_syscore_init (void ) {return 0 ; } +#endif +#endif
Signature · 1 line
1.8.1.5
PATCH v4 2/9 ARM: tegra: irq: add wake up handling
arch/arm/mach-tegra/irq.c static int tegra_retrigger(struct irq_data *d) · line 146
Quoted 12 lines · Joseph Lo
Add the wake up handling for legacy irq controller, and using
IRQCHIP_MASK_ON_SUSPENDfor wake irq handling.arch/arm/mach-tegra/irq.c +7
-0+static int tegra_set_wake (struct irq_data *d,unsigned int enable) +{ +u32 irq = d->irq; +u32 index, mask; + +BUG_ON (irq <FIRST_LEGACY_IRQ || + irq >=FIRST_LEGACY_IRQ + num_ictlrs *32 );
Perhaps that should be:
if (irq < FIRST_LEGACY_IRQ || irq >= FIRST_LEGACY_IRQ + num_ictlrs * 32) return -EINVAL;
PATCH v4 3/9 ARM: dt: tegra: add bindings of power management configurations for PMC
In reply to Joseph LoThe PMC mostly controls the entry and exit of the system from different sleep modes. Different platform or system may have different configurations. The power management configurations of PMC is represented as some properties. The system needs to define the properties when the system supports deep sleep mode (i.e. suspend).
---
V4:
* no change
V3:
* fix typos
V2:
* squash the patches that defined the PM bindings for PMC and the implementation
* replace the "unsigned long" with "u32" for the variables that are parsed from DT
--- .../bindings/arm/tegra/nvidia,tegra20-pmc.txt | 42 ++++++++++- arch/arm/mach-tegra/pmc.c | 83 ++++++++++++++++++++++ arch/arm/mach-tegra/pmc.h | 8 +++ 3 files changed, 132 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt +41 -1
@@ -1,14 +1,46 @@ NVIDIA Tegra Power Management Controller (PMC) -Properties: +The PMC block interacts with an external Power Management Unit. The PMC +mostly controls the entry and exit of the system from different sleep +modes. It provides power-gating controllers for SoC and CPU power-islands. + +Required properties: - name : Should be pmc - compatible : Should contain "nvidia,tegra<chip>-pmc". - reg : Offset and length of the register set for the device + +Optional properties: - nvidia,invert-interrupt : If present, inverts the PMU interrupt signal. The PMU is an external Power Management Unit, whose interrupt output signal is fed into the PMC. This signal is optionally inverted, and then fed into the ARM GIC. The PMC is not involved in the detection or handling of this interrupt signal, merely its inversion. +- nvidia,suspend-mode : The suspend mode that the platform should use. + Valid values are 0, 1 and 2: + 0 (LP0): CPU + Core voltage off and DRAM in self-refresh + 1 (LP1): CPU vlotage off and DRAM in self-refresh + 2 (LP2): CPU voltage off +- nvidia,core-power-req-active-high : Boolean, core power request active-high +- nvidia,sys-clock-req-active-high : Boolean, system clock request active-high +- nvidia,combined-power-req : Boolean, combined power request for CPU & Core +- nvidia,cpu-pwr-good-en : Boolean, CPU power good signal (from PMIC to PMC) + is enabled. + +Required properties when nvidia,suspend-mode is specified: +- nvidia,cpu-pwr-good-time : CPU power good time in uS. +- nvidia,cpu-pwr-off-time : CPU power off time in uS. +- nvidia,core-pwr-good-time : <Oscillator-stable-time Power-stable-time> + Core power good time in uS. +- nvidia,core-pwr-off-time : Core power off time in uS. + +Required properties when nvidia,suspend-mode=<0>: +- nvidia,lp0-vec : <start length> Starting address and length of LP0 vector + The LP0 vector contains the warm boot code that is executed by AVP when + resuming from the LP0 state. The AVP (Audio-Video Processor) is an ARM7 + processor and always being the first boot processor when chip is power on + or resume from deep sleep mode. When the system is resumed from the deep + sleep mode, the warm boot code will restore some PLLs, clocks and then + bring up CPU0 for resuming the system. Example:
@@ -16,4 +48,12 @@ pmc at 7000f400 { compatible = "nvidia,tegra20-pmc"; reg = <0x7000e400 0x400>; nvidia,invert-interrupt; + nvidia,suspend-mode = <1>; + nvidia,cpu-pwr-good-time = <2000>; + nvidia,cpu-pwr-off-time = <100>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <458>; + nvidia,core-power-req-active-high; + nvidia,sys-clock-req-active-high; + nvidia,lp0-vec = <0xbdffd000 0x2000>; };
arch/arm/mach-tegra/pmc.c +83 -0
107 lines not on this page · raw message
arch/arm/mach-tegra/pmc.h +8 -0
@@ -18,6 +18,14 @@#ifndef __MACH_TEGRA_PMC_H#define __MACH_TEGRA_PMC_H +enum tegra_suspend_mode { +TEGRA_SUSPEND_NONE =0 , +TEGRA_SUSPEND_LP2 ,/* CPU voltage off */ +TEGRA_SUSPEND_LP1 ,/* CPU voltage off, DRAM self-refresh */ +TEGRA_SUSPEND_LP0 ,/* CPU + core voltage off, DRAM self-refresh */ +TEGRA_MAX_SUSPEND_MODE , +}; +#ifdef CONFIG_PM_SLEEP void set_power_timers (unsigned long us_on,unsigned long us_off);#endif
Signature · 1 line
1.8.1.5
PATCH v4 3/9 ARM: dt: tegra: add bindings of power management configurations for PMC
Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt line 21
Quoted 12 lines · Joseph Lo
The PMC mostly controls the entry and exit of the system from different sleep modes. Different platform or system may have different configurations. The power management configurations of PMC is represented as some properties. The system needs to define the properties when the system supports deep sleep mode (i.e. suspend).
Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt +4
-0+- nvidia,suspend-mode : The suspend mode that the platform should use. + Valid values are 0, 1 and 2: + 0 (LP0): CPU + Core voltage off and DRAM in self-refresh + 1 (LP1): CPU vlotage off and DRAM in self-refresh
s/vlotage/voltage/
BTW, checkpatch spews hundreds of lines of errors because these patches have DOS-style line-endings. Can you please generate and send them directly from Linux to fix this. There are also a couple of trailing whitespace errors.
PATCH v4 3/9 ARM: dt: tegra: add bindings of power management configurations for PMC
Quoted 14 lines · Stephen Warren
Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt line 21
Quoted 12 lines · Joseph Lo
The PMC mostly controls the entry and exit of the system from different sleep modes. Different platform or system may have different configurations. The power management configurations of PMC is represented as some properties. The system needs to define the properties when the system supports deep sleep mode (i.e. suspend).
Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt +4
-0+- nvidia,suspend-mode : The suspend mode that the platform should use. + Valid values are 0, 1 and 2: + 0 (LP0): CPU + Core voltage off and DRAM in self-refresh + 1 (LP1): CPU vlotage off and DRAM in self-refresh
Quoted 6 lines
s/vlotage/voltage/
BTW, checkpatch spews hundreds of lines of errors because these patches have DOS-style line-endings. Can you please generate and send them directly from Linux to fix this. There are also a couple of trailing whitespace errors.
Oops. The DOS-style line-endings was a mistake in my work-flow, so you can ignore that. There were a few other checkpatch errors though that need fixing.
PATCH v4 4/9 ARM: tegra: pm: add platform suspend support
In reply to Joseph LoAdding suspend to RAM support for Tegra platform. There are three suspend mode for Tegra. The difference were below.
* LP2: CPU voltage off
* LP1: CPU voltage off, DRAM in self-refresh
* LP0: CPU + Core voltage off, DRAM in self-refresh
After this patch, the LP2 suspend mode will be supported.
---
V4:
* add tegra_pm_validate_suspend_mode() to validate the suspend mode config from DT
* squash the patch below that origianl being introduced after this series to clean up some PM related code
[2/3] ARM: tegra: refactor the pmc_pm_set function
V3:
* add a protection for only support LP2 suspend mode
V2:
* add the PM_SLEEP protection for "tegra_init_suspend"
* remove "tegra_suspend_{enter/exit}_lp2"
* refactor the "tegra_pmc_pm_set" for non-used parameter
* replace "unsigned long" with "u32" for tegra_pmc_get_cpu_time
--- arch/arm/mach-tegra/common.c | 1 + arch/arm/mach-tegra/pm.c | 93 +++++++++++++++++++++++++++++++++++++------- arch/arm/mach-tegra/pm.h | 15 +++++++ arch/arm/mach-tegra/pmc.c | 52 +++++++++++++++++++++++-- arch/arm/mach-tegra/pmc.h | 4 +- 5 files changed, 147 insertions(+), 18 deletions(-)
arch/arm/mach-tegra/common.c +1 -0
@@ -66,6 +66,7 @@ void __init tegra_dt_init_irq(void)tegra_init_irq ();irqchip_init ();tegra_legacy_irq_syscore_init (); + tegra_init_suspend(); }#endif
arch/arm/mach-tegra/pm.c +80 -13
118 lines not on this page · raw message
arch/arm/mach-tegra/pm.h +15 -0
@@ -21,6 +21,8 @@#ifndef _MACH_TEGRA_PM_H_#define _MACH_TEGRA_PM_H_ +#include "pmc.h" +extern unsigned long l2x0_saved_regs_addr;void save_cpu_arch_register (void );
@@ -32,4 +34,17 @@ bool tegra_set_cpu_in_lp2(int phy_cpu_id);void tegra_idle_lp2_last (u32 cpu_on_time,u32 cpu_off_time);extern void (*tegra_tear_down_cpu)(void ); +#ifdef CONFIG_PM_SLEEP +enum tegra_suspend_mode tegra_pm_validate_suspend_mode ( +enum tegra_suspend_mode mode); +void tegra_init_suspend (void ); +#else +enum tegra_suspend_mode tegra_pm_validate_suspend_mode ( +enum tegra_suspend_mode mode) +{ +return TEGRA_SUSPEND_NONE ; +} +static inline void tegra_init_suspend (void ) {} +#endif +#endif /* _MACH_TEGRA_PM_H_ */
arch/arm/mach-tegra/pmc.c +48 -4
82 lines not on this page · raw message
arch/arm/mach-tegra/pmc.h +3 -1
@@ -27,7 +27,9 @@ enum tegra_suspend_mode { };#ifdef CONFIG_PM_SLEEP -void set_power_timers (unsigned long us_on,unsigned long us_off); +enum tegra_suspend_mode tegra_pmc_get_suspend_mode (void ); +void tegra_pmc_pm_set (enum tegra_suspend_mode mode); +void tegra_pmc_suspend_init (void );#endif bool tegra_pmc_cpu_is_powered (int cpuid);
Signature · 1 line
1.8.1.5
PATCH v4 4/9 ARM: tegra: pm: add platform suspend support
Quoted 14 lines · Joseph Lo
Adding suspend to RAM support for Tegra platform. There are three suspend mode for Tegra. The difference were below.
* LP2: CPU voltage off
* LP1: CPU voltage off, DRAM in self-refresh
* LP0: CPU + Core voltage off, DRAM in self-refreshAfter this patch, the LP2 suspend mode will be supported.
arch/arm/mach-tegra/common.c +0
-0
arch/arm/mach-tegra/common.c void __init tegra_dt_init_irq(void) · line 69
Quoted 4 lines
arch/arm/mach-tegra/common.c +1
-0@@ -66,6 +66,7 @@ void __init tegra_dt_init_irq(void)tegra_init_irq ();irqchip_init ();tegra_legacy_irq_syscore_init (); +tegra_init_suspend ();
Does that have to be part of tegra_dt_init_irq()? Can't we initialize suspend support in some later hook. init_irq() should just initialize IRQs.
Quoted 5 lines
arch/arm/mach-tegra/pmc.c +1
-1-void set_power_timers (unsigned long us_on,unsigned long us_off) +static void set_power_timers (u32 us_on,u32 us_off,unsigned long rate) {
arch/arm/mach-tegra/pmc.c int tegra_pmc_cpu_remove_clamping(int cpuid) · line 175
Quoted 10 lines
arch/arm/mach-tegra/pmc.c +0
-3unsigned long long ticks;unsigned long long pclk; -unsigned long rate;static unsigned long tegra_last_pclk; - rate =clk_get_rate (tegra_pclk); -if (WARN_ON_ONCE (rate <=0 )) pclk =100000000 ;else
I don't think the code compiles after that?
The code must both compile and execute correctly after each patch is applied, without relying on any future patches.
arch/arm/mach-tegra/pmc.c void set_power_timers(unsigned long us_on, unsigned long us_off) · line 207
Quoted 12 lines
arch/arm/mach-tegra/pmc.c +12
-0+void tegra_pmc_pm_set (enum tegra_suspend_mode mode) +{ +u32 reg; +unsigned long rate =0 ; + + reg =tegra_pmc_readl (PMC_CTRL ); + reg |=TEGRA_POWER_CPU_PWRREQ_OE ; + reg &= ~TEGRA_POWER_EFFECT_LP0 ; + +switch (mode) { +case TEGRA_SUSPEND_LP2 : + rate =clk_get_rate (tegra_pclk);
That isn't used anywhere.
arch/arm/mach-tegra/pmc.c void set_power_timers(unsigned long us_on, unsigned long us_off) · line 225
Quoted 7 lines
arch/arm/mach-tegra/pmc.c +7
-0+void tegra_pmc_suspend_init (void ) +{ +u32 reg; + +/* Always enable CPU power request; just normal polarity is supported */ + reg =tegra_pmc_readl (PMC_CTRL ); +BUG_ON (reg &TEGRA_POWER_CPU_PWRREQ_POLARITY );
Why is that comment true? What does it take to support arbitrary polarity; just flipping the OE bit in the register?
PATCH v4 4/9 ARM: tegra: pm: add platform suspend support
Quoted 10 lines · Stephen Warren
Quoted 8 lines · Joseph Lo
Adding suspend to RAM support for Tegra platform. There are three suspend mode for Tegra. The difference were below.
* LP2: CPU voltage off
* LP1: CPU voltage off, DRAM in self-refresh
* LP0: CPU + Core voltage off, DRAM in self-refreshAfter this patch, the LP2 suspend mode will be supported.
Quoted 13 lines
arch/arm/mach-tegra/common.c void __init tegra_dt_init_irq(void) · line 69
Quoted 9 lines
arch/arm/mach-tegra/common.c +1
-0@@ -66,6 +66,7 @@ void __init tegra_dt_init_irq(void)tegra_init_irq ();irqchip_init ();tegra_legacy_irq_syscore_init (); +tegra_init_suspend ();Does that have to be part of
tegra_dt_init_irq()? Can't we initialize suspend support in some later hook.init_irq()should just initialize IRQs.
I can re-check the sequence later.
Quoted 18 lines
Quoted 5 lines
arch/arm/mach-tegra/pmc.c +1
-1-void set_power_timers (unsigned long us_on,unsigned long us_off) +static void set_power_timers (u32 us_on,u32 us_off,unsigned long rate) {arch/arm/mach-tegra/pmc.c int tegra_pmc_cpu_remove_clamping(int cpuid) · line 175
Quoted 10 lines
arch/arm/mach-tegra/pmc.c +0
-3unsigned long long ticks;unsigned long long pclk; -unsigned long rate;static unsigned long tegra_last_pclk; - rate =clk_get_rate (tegra_pclk); -if (WARN_ON_ONCE (rate <=0 )) pclk =100000000 ;else I don't think the code compiles after that?
Quoted 3 lines
The code must both compile and execute correctly after each patch is applied, without relying on any future patches.
It's OK. I had checked this before sending the patch.
Quoted 6 lines
Quoted 6 lines
arch/arm/mach-tegra/pmc.c +6
-0+void tegra_pmc_pm_set (enum tegra_suspend_mode mode) +{ +u32 reg; +unsigned long rate =0 ; + + reg =tegra_pmc_readl (PMC_CTRL );
Quoted 9 lines
arch/arm/mach-tegra/pmc.c void set_power_timers(unsigned long us_on, unsigned long us_off) · line 207
Quoted 6 lines
arch/arm/mach-tegra/pmc.c +6
-0+ reg |=TEGRA_POWER_CPU_PWRREQ_OE ; + reg &= ~TEGRA_POWER_EFFECT_LP0 ; + +switch (mode) { +case TEGRA_SUSPEND_LP2 : + rate =clk_get_rate (tegra_pclk);That isn't used anywhere.
It will pass to set_power_timers().
Quoted 10 lines
arch/arm/mach-tegra/pmc.c void set_power_timers(unsigned long us_on, unsigned long us_off) · line 225
Quoted 7 lines
arch/arm/mach-tegra/pmc.c +7
-0+void tegra_pmc_suspend_init (void ) +{ +u32 reg; + +/* Always enable CPU power request; just normal polarity is supported */ + reg =tegra_pmc_readl (PMC_CTRL ); +BUG_ON (reg &TEGRA_POWER_CPU_PWRREQ_POLARITY );Why is that comment true? What does it take to support arbitrary polarity; just flipping the OE bit in the register?
Hmm. You are right. I think this is redundant if we support different polarity setting. We should also add it into DT binding. So we can just flip the OE bit here.
PATCH v4 5/9 ARM: dts: tegra: add power gpio keys to DT
In reply to Joseph LoThis adds the power gpio key to DT and enable the wakeup of the gpio key for the device. The Seaboard and paz00 already had the power gpio key binding and the power key of Whistler was on KBC. So these boards' device tree didn't include in this patch.
---
V4:
* no change
V3:
* no change
V2:
* no change
--- arch/arm/boot/dts/tegra20-harmony.dts | 11 +++++++++++ arch/arm/boot/dts/tegra20-trimslice.dts | 11 +++++++++++ arch/arm/boot/dts/tegra20-ventana.dts | 11 +++++++++++ 3 files changed, 33 insertions(+)
arch/arm/boot/dts/tegra20-harmony.dts +11 -0
@@ -568,6 +568,17 @@ 0x1F0400D6>; /* KEY_QUESTION */ }; + gpio-keys { + compatible = "gpio-keys"; + + power { + label = "Power"; + gpios = <&gpio 170 1>; /* gpio PV2, active low */ + linux,code = <116>; /* KEY_POWER */ + gpio-key,wakeup; + }; + }; + regulators { compatible = "simple-bus"; #address-cells = <1>;
arch/arm/boot/dts/tegra20-trimslice.dts +11 -0
@@ -335,6 +335,17 @@ gpios = <&gpio 191 1>; /* gpio PX7, active low */ }; + gpio-keys { + compatible = "gpio-keys"; + + power { + label = "Power"; + gpios = <&gpio 190 1>; /* gpio PX6, active low */ + linux,code = <116>; /* KEY_POWER */ + gpio-key,wakeup; + }; + }; + regulators { compatible = "simple-bus"; #address-cells = <1>;
arch/arm/boot/dts/tegra20-ventana.dts +11 -0
@@ -531,6 +531,17 @@ bus-width = <8>; }; + gpio-keys { + compatible = "gpio-keys"; + + power { + label = "Power"; + gpios = <&gpio 170 1>; /* gpio PV2, active low */ + linux,code = <116>; /* KEY_POWER */ + gpio-key,wakeup; + }; + }; + regulators { compatible = "simple-bus"; #address-cells = <1>;
Signature · 1 line
1.8.1.5
PATCH v4 6/9 ARM: dts: tegra: whistler: add wakeup source for KBC
In reply to Joseph LoAdding KBC as a wakeup source for Whistler board.
---
V4:
* no change
V3:
* no change
V2:
* no change
--- arch/arm/boot/dts/tegra20-whistler.dts | 1 + 1 file changed, 1 insertion(+)
arch/arm/boot/dts/tegra20-whistler.dts +1 -0
@@ -526,6 +526,7 @@ nvidia,repeat-delay-ms = <160>; nvidia,kbc-row-pins = <0 1 2>; nvidia,kbc-col-pins = <16 17>; + nvidia,wakeup-source; linux,keymap = <0x00000074 /* KEY_POWER */ 0x01000066 /* KEY_HOME */ 0x0101009E /* KEY_BACK */
Signature · 1 line
1.8.1.5
PATCH v4 7/9 ARM: dts: tegra: add non-removable and keep-power-in-suspend property for MMC
In reply to Joseph LoThis patch adds "non-removable" property of MMC host where the eMMC device is for Tegra platform.
And the "keep-power-in-suspend" property was used for the SDIO device that need this to go into suspend mode (e.g. BRCM43xx series).
---
V4:
* no change
V3:
* no change
V2:
* no change
--- arch/arm/boot/dts/tegra20-paz00.dts | 1 + arch/arm/boot/dts/tegra20-seaboard.dts | 2 ++ arch/arm/boot/dts/tegra20-ventana.dts | 2 ++ arch/arm/boot/dts/tegra20-whistler.dts | 1 + arch/arm/boot/dts/tegra30-beaver.dts | 1 + arch/arm/boot/dts/tegra30-cardhu-a02.dts | 1 + arch/arm/boot/dts/tegra30-cardhu-a04.dts | 1 + arch/arm/boot/dts/tegra30-cardhu.dtsi | 1 + 8 files changed, 10 insertions(+)
arch/arm/boot/dts/tegra20-paz00.dts +1 -0
@@ -445,6 +445,7 @@ sdhci at c8000600 { status = "okay"; bus-width = <8>; + non-removable; }; gpio-keys {
arch/arm/boot/dts/tegra20-seaboard.dts +2 -0
@@ -580,6 +580,7 @@ status = "okay"; power-gpios = <&gpio 86 0>; /* gpio PK6 */ bus-width = <4>; + keep-power-in-suspend; }; sdhci at c8000400 {
@@ -593,6 +594,7 @@ sdhci at c8000600 { status = "okay"; bus-width = <8>; + non-removable; }; gpio-keys {
arch/arm/boot/dts/tegra20-ventana.dts +2 -0
@@ -516,6 +516,7 @@ status = "okay"; power-gpios = <&gpio 86 0>; /* gpio PK6 */ bus-width = <4>; + keep-power-in-suspend; }; sdhci at c8000400 {
@@ -529,6 +530,7 @@ sdhci at c8000600 { status = "okay"; bus-width = <8>; + non-removable; }; gpio-keys {
arch/arm/boot/dts/tegra20-whistler.dts +1 -0
@@ -518,6 +518,7 @@ sdhci at c8000600 { status = "okay"; bus-width = <8>; + non-removable; }; kbc {
arch/arm/boot/dts/tegra30-beaver.dts +1 -0
@@ -266,6 +266,7 @@ sdhci at 78000600 { status = "okay"; bus-width = <8>; + non-removable; }; regulators {
arch/arm/boot/dts/tegra30-cardhu-a02.dts +1 -0
@@ -88,6 +88,7 @@ status = "okay"; power-gpios = <&gpio 28 0>; /* gpio PD4 */ bus-width = <4>; + keep-power-in-suspend; }; };
arch/arm/boot/dts/tegra30-cardhu-a04.dts +1 -0
@@ -100,5 +100,6 @@ status = "okay"; power-gpios = <&gpio 27 0>; /* gpio PD3 */ bus-width = <4>; + keep-power-in-suspend; }; };
arch/arm/boot/dts/tegra30-cardhu.dtsi +1 -0
@@ -320,6 +320,7 @@ sdhci at 78000600 { status = "okay"; bus-width = <8>; + non-removable; }; regulators {
Signature · 1 line
1.8.1.5
PATCH v4 8/9 ARM: tegra: config: defconfig update
In reply to Joseph LoKEYBOARD_GPIO:
* Enable gpio-key driver
---
V8:
* no change
V3:
* no change
V2:
* no change
--- arch/arm/configs/tegra_defconfig | 1 + 1 file changed, 1 insertion(+)
arch/arm/configs/tegra_defconfig +1 -0
@@ -108,6 +108,7 @@ CONFIG_RT2X00=y CONFIG_RT2800USB=m CONFIG_INPUT_EVDEV=y CONFIG_KEYBOARD_TEGRA=y +CONFIG_KEYBOARD_GPIO=y CONFIG_INPUT_MISC=y CONFIG_INPUT_MPU3050=y # CONFIG_LEGACY_PTYS is not set
Signature · 1 line
1.8.1.5
PATCH v4 9/9 ARM: dts: tegra: add the PM configurations of PMC
In reply to Joseph LoAdding the PM configuration of PMC when the platform support suspend function.
---
V4:
* no change
V3:
* fix the configuration for paz00 board
V2:
* no change
--- arch/arm/boot/dts/tegra20-harmony.dts | 6 ++++++ arch/arm/boot/dts/tegra20-paz00.dts | 6 ++++++ arch/arm/boot/dts/tegra20-seaboard.dts | 6 ++++++ arch/arm/boot/dts/tegra20-trimslice.dts | 9 +++++++++ arch/arm/boot/dts/tegra20-ventana.dts | 6 ++++++ arch/arm/boot/dts/tegra20-whistler.dts | 8 ++++++++ arch/arm/boot/dts/tegra30-beaver.dts | 7 +++++++ arch/arm/boot/dts/tegra30-cardhu.dtsi | 7 +++++++ 8 files changed, 55 insertions(+)
arch/arm/boot/dts/tegra20-harmony.dts +6 -0
@@ -416,6 +416,12 @@ pmc { nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <5000>; + nvidia,cpu-pwr-off-time = <5000>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <3875>; + nvidia,sys-clock-req-active-high; }; usb at c5000000 {
arch/arm/boot/dts/tegra20-paz00.dts +6 -0
@@ -415,6 +415,12 @@ pmc { nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <2000>; + nvidia,cpu-pwr-off-time = <0>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <0>; + nvidia,sys-clock-req-active-high; }; usb at c5000000 {
arch/arm/boot/dts/tegra20-seaboard.dts +6 -0
@@ -517,6 +517,12 @@ pmc { nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <5000>; + nvidia,cpu-pwr-off-time = <5000>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <3875>; + nvidia,sys-clock-req-active-high; }; memory-controller at 7000f400 {
arch/arm/boot/dts/tegra20-trimslice.dts +9 -0
@@ -300,6 +300,15 @@ }; }; + pmc { + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <5000>; + nvidia,cpu-pwr-off-time = <5000>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <3875>; + nvidia,sys-clock-req-active-high; + }; + usb at c5000000 { status = "okay"; nvidia,vbus-gpio = <&gpio 170 0>; /* gpio PV2 */
arch/arm/boot/dts/tegra20-ventana.dts +6 -0
@@ -493,6 +493,12 @@ pmc { nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <2000>; + nvidia,cpu-pwr-off-time = <100>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <458>; + nvidia,sys-clock-req-active-high; }; usb at c5000000 {
arch/arm/boot/dts/tegra20-whistler.dts +8 -0
@@ -496,6 +496,14 @@ pmc { nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <2000>; + nvidia,cpu-pwr-off-time = <1000>; + nvidia,core-pwr-good-time = <0 3845>; + nvidia,core-pwr-off-time = <93727>; + nvidia,core-power-req-active-high; + nvidia,sys-clock-req-active-high; + nvidia,combined-power-req; }; usb at c5000000 {
arch/arm/boot/dts/tegra30-beaver.dts +7 -0
@@ -253,6 +253,13 @@ pmc { status = "okay"; nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <2000>; + nvidia,cpu-pwr-off-time = <200>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <0>; + nvidia,core-power-req-active-high; + nvidia,sys-clock-req-active-high; }; sdhci at 78000000 {
arch/arm/boot/dts/tegra30-cardhu.dtsi +7 -0
@@ -307,6 +307,13 @@ pmc { status = "okay"; nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <2000>; + nvidia,cpu-pwr-off-time = <200>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <0>; + nvidia,core-power-req-active-high; + nvidia,sys-clock-req-active-high; }; sdhci at 78000000 {
Signature · 1 line
1.8.1.5
v4 cover ARM: tegra: add platform suspend support
In reply to Joseph LoQuoted 9 lines · Joseph Lo
This series introduces a basic functionality for Tegra to support the platform suspend and resume.
Note: This series only adds the support for Tegra20 and Tegra30. The Tegra114 will be supported later.
This series needs the patch below that not yet be merged into linux-mmc tree to make the system suspend/resume function work correctly.
"mmc: tegra: usemmc_of_parseto get the support of standard MMC DT bindings"
I assume this series needs to be applied after the 3-long series you posted just before it, containing "ARM: dts: tegra: add clock source for PMC", "ARM: tegra: get PMC clock source from DT", and "ARM: tegra:
moving the CPU power timer function to PMC driver"?
v4 cover ARM: tegra: add platform suspend support
Quoted 7 lines · Stephen Warren
Quoted 6 lines · Joseph Lo
This series introduces a basic functionality for Tegra to support the platform suspend and resume.
Note: This series only adds the support for Tegra20 and Tegra30. The Tegra114 will be supported later.
Quoted 8 lines
Quoted 3 lines
This series needs the patch below that not yet be merged into linux-mmc tree to make the system suspend/resume function work correctly.
"mmc: tegra: usemmc_of_parseto get the support of standard MMC DT bindings"I assume this series needs to be applied after the 3-long series you posted just before it, containing "ARM: dts: tegra: add clock source for PMC", "ARM: tegra: get PMC clock source from DT", and "ARM: tegra:
moving the CPU power timer function to PMC driver"?
Oops, I mentioned this in the cover letter there and forgot to add here. Yes, thanks for taking care.