Skip to contentSkip to conversation

DTS at91sam9x5cm: add 1-wire chip on CM board

PATCH In review Richard Genoud 2 participants 2 messages Mar 20, 2013 – Mar 21, 2013

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 DTS at91sam9x5cm: add 1-wire chip on CM board

This add the 1-wire chip present on the CM board to the DTS. As the pin is also used by leds, tt's disabled by default. If the board really wants it, it can be enabled in the board DTS.

---
 arch/arm/boot/dts/at91sam9x5cm.dtsi |   20 ++++++++++++++++++++
 1 files changed, 20 insertions(+), 0 deletions(-)
arch/arm/boot/dts/at91sam9x5cm.dtsi +20 -0
index 4027ac7..347a74a 100644
@@ -24,6 +24,16 @@
 	};
 
 	ahb {
+		apb {
+			pinctrl at fffff400 {
+				1wire_cm {
+					pinctrl_1wire_cm: 1wire_cm-0 {
+						atmel,pins = <1 18 0x0 0x2>; /* PB18 multidrive, conflicts with led */
+					};
+				};
+			};
+		};
+
 		nand0: nand at 40000000 {
 			nand-bus-width = <8>;
 			nand-ecc-mode = "hw";
@@ -74,4 +84,14 @@
 			gpios = <&pioD 21 0>;
 		};
 	};
+
+	1wire_cm {
+		compatible = "w1-gpio";
+		gpios = <&pioB 18 0>;
+		linux,open-drain;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_1wire_cm>;
+		status = "okay";
+	};
+
 };
Signature · 1 line
1.7.2.5
Acked-by on v1 1/1
#1 lore raw

On 03/20/2013 12:23 PM, Richard Genoud :

Quoted 5 lines

This add the 1-wire chip present on the CM board to the DTS. As the pin is also used by leds, tt's disabled by default. If the board really wants it, it can be enabled in the board DTS.

And pushed to at91-3.10-dt branch.

Thanks,

Quoted 41 lines
---
 arch/arm/boot/dts/at91sam9x5cm.dtsi |   20 ++++++++++++++++++++
 1 files changed, 20 insertions(+), 0 deletions(-)
arch/arm/boot/dts/at91sam9x5cm.dtsi +20 -0
index 4027ac7..347a74a 100644
@@ -24,6 +24,16 @@
 	};
 
 	ahb {
+		apb {
+			pinctrl at fffff400 {
+				1wire_cm {
+					pinctrl_1wire_cm: 1wire_cm-0 {
+						atmel,pins = <1 18 0x0 0x2>; /* PB18 multidrive, conflicts with led */
+					};
+				};
+			};
+		};
+
 		nand0: nand at 40000000 {
 			nand-bus-width = <8>;
 			nand-ecc-mode = "hw";
@@ -74,4 +84,14 @@
 			gpios = <&pioD 21 0>;
 		};
 	};
+
+	1wire_cm {
+		compatible = "w1-gpio";
+		gpios = <&pioB 18 0>;
+		linux,open-drain;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_1wire_cm>;
+		status = "okay";
+	};
+
 };
Signature · 1 line
Nicolas Ferre