Skip to contentSkip to conversation

ARM: tegra: dalmore: add regulators

PATCH In review Laxman Dewangan 3 participants 8 messages Mar 21, 2013 – Mar 22, 2013

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

v2 cover ARM: tegra: dalmore: add regulators

This series add the regulators for Dalmore platform. Dalmore also have the Palma PMIC as primary PMIC but dt population will be send later once DT documentation finalize.

Changes from V1:
- Rearrange patches so that config change will be last patch.
- Correct some sentence and Caps.
- fix compilation issue arise in mid of patches.

Laxman Dewangan (4):
ARM: tegra: dalmore: add cpu regulator node
ARM: tegra: dalmore: add TPS65090 node
ARM: tegra: dalmore: add fixed regulator node
ARM: tegra: enable Tegra114 based platform PMICs

 arch/arm/boot/dts/tegra114-dalmore.dts |  162 ++++++++++++++++++++++++++++++++
 arch/arm/configs/tegra_defconfig       |    7 ++
 2 files changed, 169 insertions(+), 0 deletions(-)
#1 lore raw

PATCH v2 1/4 ARM: tegra: dalmore: add cpu regulator node

Dalmore uses the TPS51632 as CPU regulator. The device is connected on I2C5.

Add DT node for TPS51632.

---
 arch/arm/boot/dts/tegra114-dalmore.dts |   15 +++++++++++++++
 1 files changed, 15 insertions(+), 0 deletions(-)
arch/arm/boot/dts/tegra114-dalmore.dts +15 -0
index a61974e..6be9434 100644
@@ -718,6 +718,21 @@
 		clock-frequency = <408000000>;
 	};
 
+	i2c at 7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		tps51632 {
+			compatible = "ti,tps51632";
+			reg = <0x43>;
+			regulator-name = "vdd-cpu";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1520000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+	};
+
 	pmc {
 		nvidia,invert-interrupt;
 	};
Signature · 1 line
1.7.1.1
#2 lore raw

Re: [PATCH V2 1/4] ARM: tegra: dalmore: add cpu regulator node

Hello.

Quoted 15 lines · Laxman Dewangan

Dalmore uses the TPS51632 as CPU regulator. The device is connected on I2C5.

Add DT node for TPS51632.

---
  arch/arm/boot/dts/tegra114-dalmore.dts |   15 +++++++++++++++
  1 files changed, 15 insertions(+), 0 deletions(-)
arch/arm/boot/dts/tegra114-dalmore.dts +0 -0
index a61974e..6be9434 100644

arch/arm/boot/dts/tegra114-dalmore.dts line 725

Quoted 8 lines
arch/arm/boot/dts/tegra114-dalmore.dts +5 -0
@@ -718,6 +718,21 @@
  		clock-frequency = <408000000>;
  	};
 
+	i2c at 7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		tps51632 {

Should be named "tps51632 at 43" I think.

arch/arm/boot/dts/tegra114-dalmore.dts line 727

Quoted 2 lines
arch/arm/boot/dts/tegra114-dalmore.dts +2 -0
+			compatible = "ti,tps51632";
+			reg = <0x43>;

WBR, Sergei

#3 lore raw

Re: [PATCH V2 1/4] ARM: tegra: dalmore: add cpu regulator node

Quoted 11 lines · Sergei Shtylyov

Hello.

Quoted 6 lines · Laxman Dewangan

Dalmore uses the TPS51632 as CPU regulator. The device is connected on I2C5.

Add DT node for TPS51632.

(quoted diff) +0 -0
Quoted 7 lines

arch/arm/boot/dts/tegra114-dalmore.dts line 725

Quoted 5 lines
arch/arm/boot/dts/tegra114-dalmore.dts +5 -0
+    i2c at 7000d000 {
+        status = "okay";
+        clock-frequency = <400000>;
+
+        tps51632 {

Should be named "tps51632 at 43" I think.

The unit-address (i.e. "@43" part) of the node name is typically omitted if it isn't required to make the node name unique.

#4 lore raw

PATCH v2 2/4 ARM: tegra: dalmore: add TPS65090 node

In reply to Laxman Dewangan

NVIDIA's Tegra114 reference platform, Dalmore, uses the TPS65090 as secondary PMICs which is mainly act as voltage switch regulator controlled by i2c communication.

Add DT node for TPS65090.

---
Changes from V1:
- Fix compilation error on this patch which was introduced on prev set.

 arch/arm/boot/dts/tegra114-dalmore.dts |   92 ++++++++++++++++++++++++++++++++
 1 files changed, 92 insertions(+), 0 deletions(-)
arch/arm/boot/dts/tegra114-dalmore.dts +92 -0
index 6be9434..6e9d757 100644
@@ -731,6 +731,83 @@
 			regulator-boot-on;
 			regulator-always-on;
 		};
+
+		tps65090 at 48 {
+			compatible = "ti,tps65090";
+			reg = <0x48>;
+			interrupt-parent = <&gpio>;
+			interrupts = <72 0x04>; /* gpio PJ0 */
+
+			vsys1-supply = <&vdd_ac_bat_reg>;
+			vsys2-supply = <&vdd_ac_bat_reg>;
+			vsys3-supply = <&vdd_ac_bat_reg>;
+			infet1-supply = <&vdd_ac_bat_reg>;
+			infet2-supply = <&vdd_ac_bat_reg>;
+			infet3-supply = <&tps65090_dcdc2_reg>;
+			infet4-supply = <&tps65090_dcdc2_reg>;
+			infet5-supply = <&tps65090_dcdc2_reg>;
+			infet6-supply = <&tps65090_dcdc2_reg>;
+			infet7-supply = <&tps65090_dcdc2_reg>;
+			vsys-l1-supply = <&vdd_ac_bat_reg>;
+			vsys-l2-supply = <&vdd_ac_bat_reg>;
+
+			regulators {
+				dcdc1 {
+					regulator-name = "vdd-sys-5v0";
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				tps65090_dcdc2_reg: dcdc2 {
+					regulator-name = "vdd-sys-3v3";
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				dcdc3 {
+					regulator-name = "vdd-ao";
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				fet1 {
+					regulator-name = "vdd-lcd-bl";
+				};
+
+				fet3 {
+					regulator-name = "vdd-modem-3v3";
+				};
+
+				fet4 {
+					regulator-name = "avdd-lcd";
+				};
+
+				fet5 {
+					regulator-name = "vdd-lvds";
+				};
+
+				fet6 {
+					regulator-name = "vdd-sd-slot";
+					regulator-boot-on;
+				};
+
+				fet7 {
+					regulator-name = "vdd-com-3v3";
+				};
+
+				ldo1 {
+					regulator-name = "vdd-sby-5v0";
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				ldo2 {
+					regulator-name = "vdd-sby-3v3";
+					regulator-always-on;
+					regulator-boot-on;
+				};
+			};
+		};
 	};
 
 	pmc {
@@ -747,4 +824,19 @@
 		bus-width = <8>;
 		status = "okay";
 	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vdd_ac_bat_reg: regulator at 0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "vdd_ac_bat";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			regulator-always-on;
+		};
+	};
 };
Signature · 1 line
1.7.1.1
#5 lore raw

PATCH v2 3/4 ARM: tegra: dalmore: add fixed regulator node

In reply to Laxman Dewangan

NVIDIA's Tegra114 reference platform Dalmore has voltage switch regulators which are controlled by the Tegra GPIOs.

Add DT node for fixed regulators.

---
 arch/arm/boot/dts/tegra114-dalmore.dts |   57 +++++++++++++++++++++++++++++++-
 1 files changed, 56 insertions(+), 1 deletions(-)
arch/arm/boot/dts/tegra114-dalmore.dts +56 -1
index 6e9d757..6ad1f45 100644
@@ -752,7 +752,7 @@
 			vsys-l2-supply = <&vdd_ac_bat_reg>;
 
 			regulators {
-				dcdc1 {
+				tps65090_dcdc1_reg: dcdc1 {
 					regulator-name = "vdd-sys-5v0";
 					regulator-always-on;
 					regulator-boot-on;
@@ -838,5 +838,60 @@
 			regulator-max-microvolt = <5000000>;
 			regulator-always-on;
 		};
+
+		dvdd_ts_reg: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "dvdd_ts";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			enable-active-high;
+			gpio = <&gpio 61 0>; /* GPIO PH5 */
+		};
+
+		lcd_bl_en_reg: regulator at 2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "lcd_bl_en";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			gpio = <&gpio 58 0>; /* GPIO PH2 */
+		};
+
+		usb1_vbus_reg: regulator at 3 {
+			compatible = "regulator-fixed";
+			reg = <3>;
+			regulator-name = "usb1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			gpio = <&gpio 108 0>; /* GPIO PN4 */
+			gpio-open-drain;
+			vin-supply = <&tps65090_dcdc1_reg>;
+		};
+
+		usb3_vbus_reg: regulator at 4 {
+			compatible = "regulator-fixed";
+			reg = <4>;
+			regulator-name = "usb2_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			gpio = <&gpio 86 0>; /* GPIO PK6 */
+			gpio-open-drain;
+			vin-supply = <&tps65090_dcdc1_reg>;
+		};
+
+		vdd_hdmi_reg: regulator at 5 {
+			compatible = "regulator-fixed";
+			reg = <5>;
+			regulator-name = "vdd_hdmi_5v0";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			gpio = <&gpio 81 0>; /* GPIO PK1 */
+			vin-supply = <&tps65090_dcdc1_reg>;
+		};
 	};
 };
Signature · 1 line
1.7.1.1
#6 lore raw

PATCH v2 4/4 ARM: tegra: enable Tegra114 based platform PMICs

In reply to Laxman Dewangan

NVIDIA's Tegra114 has two reference platforms, Dalmore and Pluto. Dalmore uses following PMICs:
- TPS65913 as primary PMIC.
- TPS65090 as secondary PMIC used for switch regulators and battery charging.
- TPS51632 for CPU regulator.

Pluto uses only TPS65913.

Enable config variable for these PMICs for Dalomore and Pluto.

---
Changes from V1:
- Rearrange patch to make it 4th patch.

 arch/arm/configs/tegra_defconfig |    7 +++++++
 1 files changed, 7 insertions(+), 0 deletions(-)
arch/arm/configs/tegra_defconfig +7 -0
index aba4881..34b9342 100644
@@ -126,6 +126,7 @@ CONFIG_SPI=y
 CONFIG_SPI_TEGRA20_SFLASH=y
 CONFIG_SPI_TEGRA20_SLINK=y
 CONFIG_GPIO_PCA953X_IRQ=y
+CONFIG_GPIO_PALMAS=y
 CONFIG_GPIO_TPS6586X=y
 CONFIG_GPIO_TPS65910=y
 CONFIG_POWER_SUPPLY=y
@@ -136,12 +137,17 @@ CONFIG_SENSORS_LM90=y
 CONFIG_MFD_TPS6586X=y
 CONFIG_MFD_TPS65910=y
 CONFIG_MFD_MAX8907=y
+CONFIG_MFD_TPS65090=y
+CONFIG_MFD_PALMAS=y
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_VIRTUAL_CONSUMER=y
 CONFIG_REGULATOR_GPIO=y
 CONFIG_REGULATOR_MAX8907=y
+CONFIG_REGULATOR_PALMAS=y
+CONFIG_REGULATOR_TPS51632=y
 CONFIG_REGULATOR_TPS62360=y
+CONFIG_REGULATOR_TPS65090=y
 CONFIG_REGULATOR_TPS6586X=y
 CONFIG_REGULATOR_TPS65910=y
 CONFIG_MEDIA_SUPPORT=y
@@ -191,6 +197,7 @@ CONFIG_RTC_INTF_SYSFS=y
 CONFIG_RTC_INTF_PROC=y
 CONFIG_RTC_INTF_DEV=y
 CONFIG_RTC_DRV_MAX8907=y
+CONFIG_RTC_DRV_PALMAS=y
 CONFIG_RTC_DRV_TPS6586X=y
 CONFIG_RTC_DRV_TPS65910=y
 CONFIG_RTC_DRV_EM3027=y
Signature · 1 line
1.7.1.1
#7 lore raw
In reply to Laxman Dewangan
Quoted 4 lines · Laxman Dewangan

This series add the regulators for Dalmore platform. Dalmore also have the Palma PMIC as primary PMIC but dt population will be send later once DT documentation finalize.

The series is applied. The first 3 patches to Tegra's for-3.10/dt branch, and patch 4 to Tegra's for-3.10/defconfig banch.

In patch 2,

Review

Quoted 1 line
(quoted diff) +1 -0
+		tps65090 at 48 {

I removed "@48" there, since the unit-address isn't required to make the node name unique.