ARM: tegra: add platform suspend support
Subsystems (5)
v6 cover ARM: tegra: add platform suspend support
This series introduces a basic functionality for Tegra to support the platform suspend and resume.
Note: This series only adds the support for Tegra20 and Tegra30. The Tegra114 will be supported later.
Verified on Seaboard and Cardhu.
V6:
* add more boards support by dts file
V5:
* some fixes from V4's review comments
V4:
* add tegra_pm_validate_suspend_mode() to validate the suspend mode config from DT
* squash the patch below into [4/9] to avoid churn after this series [2/3] ARM: tegra: refactor the pmc_pm_set function
V3:
* fix the PMC DT configurations for paz00 board
* add a protection for only support LP2 suspend mode
V2:
* re-order the patch sequence to make sure the suspend function can be enabled well after the last patch be merged
* squash the patches that defined the PM bindings for PMC and the implementation
Joseph Lo (9):
gpio: tegra: add gpio wakeup source handling
ARM: tegra: irq: add wake up handling
ARM: dt: tegra: add bindings of power management configurations for
PMC
ARM: tegra: pm: add platform suspend support
ARM: dts: tegra: add power gpio keys to DT
ARM: dts: tegra: whistler: add wakeup source for KBC
ARM: dts: tegra: add non-removable and keep-power-in-suspend property
for MMC
ARM: tegra: config: defconfig update
ARM: dts: tegra: add the PM configurations of PMC
.../bindings/arm/tegra/nvidia,tegra20-pmc.txt | 38 ++++++ arch/arm/boot/dts/tegra114-dalmore.dts | 1 + arch/arm/boot/dts/tegra20-colibri-512.dtsi | 9 ++ arch/arm/boot/dts/tegra20-harmony.dts | 17 +++ arch/arm/boot/dts/tegra20-paz00.dts | 7 ++ arch/arm/boot/dts/tegra20-seaboard.dts | 8 ++ arch/arm/boot/dts/tegra20-tamonten.dtsi | 6 + arch/arm/boot/dts/tegra20-trimslice.dts | 20 ++++ arch/arm/boot/dts/tegra20-ventana.dts | 19 +++ arch/arm/boot/dts/tegra20-whistler.dts | 10 ++ arch/arm/boot/dts/tegra30-beaver.dts | 8 ++ arch/arm/boot/dts/tegra30-cardhu-a02.dts | 1 + arch/arm/boot/dts/tegra30-cardhu-a04.dts | 1 + arch/arm/boot/dts/tegra30-cardhu.dtsi | 8 ++ arch/arm/configs/tegra_defconfig | 1 + arch/arm/mach-tegra/common.c | 3 + arch/arm/mach-tegra/irq.c | 96 ++++++++++++++- arch/arm/mach-tegra/irq.h | 6 + arch/arm/mach-tegra/pm.c | 93 ++++++++++++-- arch/arm/mach-tegra/pm.h | 15 +++ arch/arm/mach-tegra/pmc.c | 133 ++++++++++++++++++++- arch/arm/mach-tegra/pmc.h | 12 +- drivers/gpio/gpio-tegra.c | 21 +++- 23 files changed, 513 insertions(+), 20 deletions(-)
Signature · 1 line
1.8.2
PATCH v6 1/9 gpio: tegra: add gpio wakeup source handling
This patch add the gpio wakeup source handling for the Tegra platform. It was be done by enabling the irq for the gpio in the gpio controller and enabling the bank irq of the gpio in the Tegra legacy irq controller when the system going to suspend.
Based on the work by:
Varun Wadekar <[email protected]>
---
V6:
* no change
V5:
* no change
V4:
* no change
V3:
* no change
V2:
* no change
--- drivers/gpio/gpio-tegra.c | 21 +++++++++++++++++++-- 1 file changed, 19 insertions(+), 2 deletions(-)
drivers/gpio/gpio-tegra.c +19 -2
@@ -72,6 +72,7 @@ struct tegra_gpio_bank {u32 oe[4 ];u32 int_enb[4 ];u32 int_lvl[4 ]; +u32 wake_enb[4 ];#endif };
@@ -333,15 +334,31 @@ static int tegra_gpio_suspend(struct device *dev) bank->oe[p] =tegra_gpio_readl (GPIO_OE (gpio)); bank->int_enb[p] =tegra_gpio_readl (GPIO_INT_ENB (gpio)); bank->int_lvl[p] =tegra_gpio_readl (GPIO_INT_LVL (gpio)); + +/* Enable gpio irq for wake up source */ +tegra_gpio_writel (bank->wake_enb[p], + GPIO_INT_ENB(gpio)); } }local_irq_restore (flags);return 0 ; } -static int tegra_gpio_wake_enable (struct irq_data *d,unsigned int enable) +static int tegra_gpio_irq_set_wake (struct irq_data *d,unsigned int enable) {struct tegra_gpio_bank *bank =irq_data_get_irq_chip_data (d); +int gpio = d->hwirq; +u32 port, bit, mask; + + port =GPIO_PORT (gpio); + bit =GPIO_BIT (gpio); + mask =BIT (bit); + +if (enable) + bank->wake_enb[port] |= mask; +else + bank->wake_enb[port] &= ~mask; +return irq_set_irq_wake (bank->irq, enable); }#endif
@@ -353,7 +370,7 @@ static struct irq_chip tegra_gpio_irq_chip = { .irq_unmask = tegra_gpio_irq_unmask, .irq_set_type = tegra_gpio_irq_set_type, #ifdef CONFIG_PM_SLEEP - .irq_set_wake = tegra_gpio_wake_enable, + .irq_set_wake = tegra_gpio_irq_set_wake,#endif };
Signature · 1 line
1.8.2
PATCH v6 2/9 ARM: tegra: irq: add wake up handling
In reply to Joseph LoAdd the wake up handling for legacy irq controller, and using IRQCHIP_MASK_ON_SUSPEND for wake irq handling.
Based on the work by:
Varun Wadekar <[email protected]>
---
V6:
* no change
V5:
* don't use BUG_ON when irq_nr is not correct in set_wake function V4:
* no change
V3:
* no change
V2:
* no change
--- arch/arm/mach-tegra/common.c | 2 + arch/arm/mach-tegra/irq.c | 96 +++++++++++++++++++++++++++++++++++++++++++- arch/arm/mach-tegra/irq.h | 6 +++ 3 files changed, 103 insertions(+), 1 deletion(-)
arch/arm/mach-tegra/common.c +2 -0
@@ -33,6 +33,7 @@#include "common.h" #include "fuse.h" #include "iomap.h" +#include "irq.h" #include "pmc.h" #include "apbio.h" #include "sleep.h"
@@ -64,6 +65,7 @@ void __init tegra_dt_init_irq(void)tegra_pmc_init ();tegra_init_irq ();irqchip_init (); + tegra_legacy_irq_syscore_init(); }#endif
arch/arm/mach-tegra/irq.c +95 -1
132 lines not on this page · raw message
arch/arm/mach-tegra/irq.h +6 -0
@@ -19,4 +19,10 @@bool tegra_pending_sgi (void ); +#ifdef CONFIG_PM_SLEEP +int tegra_legacy_irq_syscore_init (void ); +#else +static inline int tegra_legacy_irq_syscore_init (void ) {return 0 ; } +#endif +#endif
Signature · 1 line
1.8.2
PATCH v6 3/9 ARM: dt: tegra: add bindings of power management configurations for PMC
In reply to Joseph LoThe PMC mostly controls the entry and exit of the system from different sleep modes. Different platform or system may have different configurations. The power management configurations of PMC is represented as some properties. The system needs to define the properties when the system supports deep sleep mode (i.e. suspend).
---
V6:
* no change
V5:
* fix typos
V4:
* no change
V3:
* fix typos
V2:
* squash the patches that defined the PM bindings for PMC and the implementation
* replace the "unsigned long" with "u32" for the variables that are parsed from DT
--- .../bindings/arm/tegra/nvidia,tegra20-pmc.txt | 38 ++++++++++ arch/arm/mach-tegra/pmc.c | 83 ++++++++++++++++++++++ arch/arm/mach-tegra/pmc.h | 8 +++ 3 files changed, 129 insertions(+)
Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt +38 -0
@@ -1,5 +1,9 @@ NVIDIA Tegra Power Management Controller (PMC) +The PMC block interacts with an external Power Management Unit. The PMC +mostly controls the entry and exit of the system from different sleep +modes. It provides power-gating controllers for SoC and CPU power-islands. + Required properties: - name : Should be pmc - compatible : Should contain "nvidia,tegra<chip>-pmc".
@@ -15,6 +19,32 @@ Optional properties: signal is fed into the PMC. This signal is optionally inverted, and then fed into the ARM GIC. The PMC is not involved in the detection or handling of this interrupt signal, merely its inversion. +- nvidia,suspend-mode : The suspend mode that the platform should use. + Valid values are 0, 1 and 2: + 0 (LP0): CPU + Core voltage off and DRAM in self-refresh + 1 (LP1): CPU voltage off and DRAM in self-refresh + 2 (LP2): CPU voltage off +- nvidia,core-power-req-active-high : Boolean, core power request active-high +- nvidia,sys-clock-req-active-high : Boolean, system clock request active-high +- nvidia,combined-power-req : Boolean, combined power request for CPU & Core +- nvidia,cpu-pwr-good-en : Boolean, CPU power good signal (from PMIC to PMC) + is enabled. + +Required properties when nvidia,suspend-mode is specified: +- nvidia,cpu-pwr-good-time : CPU power good time in uS. +- nvidia,cpu-pwr-off-time : CPU power off time in uS. +- nvidia,core-pwr-good-time : <Oscillator-stable-time Power-stable-time> + Core power good time in uS. +- nvidia,core-pwr-off-time : Core power off time in uS. + +Required properties when nvidia,suspend-mode=<0>: +- nvidia,lp0-vec : <start length> Starting address and length of LP0 vector + The LP0 vector contains the warm boot code that is executed by AVP when + resuming from the LP0 state. The AVP (Audio-Video Processor) is an ARM7 + processor and always being the first boot processor when chip is power on + or resume from deep sleep mode. When the system is resumed from the deep + sleep mode, the warm boot code will restore some PLLs, clocks and then + bring up CPU0 for resuming the system. Example:
@@ -25,6 +55,14 @@ pmc at 7000f400 { clocks = <&tegra_car 110>, <&clk32k_in>; clock-names = "pclk", "clk32k_in"; nvidia,invert-interrupt; + nvidia,suspend-mode = <1>; + nvidia,cpu-pwr-good-time = <2000>; + nvidia,cpu-pwr-off-time = <100>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <458>; + nvidia,core-power-req-active-high; + nvidia,sys-clock-req-active-high; + nvidia,lp0-vec = <0xbdffd000 0x2000>; }; / Tegra board dts file
arch/arm/mach-tegra/pmc.c +83 -0
107 lines not on this page · raw message
arch/arm/mach-tegra/pmc.h +8 -0
@@ -18,6 +18,14 @@#ifndef __MACH_TEGRA_PMC_H#define __MACH_TEGRA_PMC_H +enum tegra_suspend_mode { +TEGRA_SUSPEND_NONE =0 , +TEGRA_SUSPEND_LP2 ,/* CPU voltage off */ +TEGRA_SUSPEND_LP1 ,/* CPU voltage off, DRAM self-refresh */ +TEGRA_SUSPEND_LP0 ,/* CPU + core voltage off, DRAM self-refresh */ +TEGRA_MAX_SUSPEND_MODE , +}; +#ifdef CONFIG_PM_SLEEP void set_power_timers (unsigned long us_on,unsigned long us_off);#endif
Signature · 1 line
1.8.2
PATCH v6 4/9 ARM: tegra: pm: add platform suspend support
In reply to Joseph LoAdding suspend to RAM support for Tegra platform. There are three suspend mode for Tegra. The difference were below.
* LP2: CPU voltage off
* LP1: CPU voltage off, DRAM in self-refresh
* LP0: CPU + Core voltage off, DRAM in self-refresh
After this patch, the LP2 suspend mode will be supported.
---
V6:
* no change
V5:
* move tegra_init_suspend() to tegra_init_late()
* remove useless BUG_ON for the polarity of CPU power request V4:
* add tegra_pm_validate_suspend_mode() to validate the suspend mode config from DT
* squash the patch below that origianl being introduced after this series to clean up some PM related code
[2/3] ARM: tegra: refactor the pmc_pm_set function
V3:
* add a protection for only support LP2 suspend mode
V2:
* add the PM_SLEEP protection for "tegra_init_suspend"
* remove "tegra_suspend_{enter/exit}_lp2"
* refactor the "tegra_pmc_pm_set" for non-used parameter
* replace "unsigned long" with "u32" for tegra_pmc_get_cpu_time
--- arch/arm/mach-tegra/common.c | 1 + arch/arm/mach-tegra/pm.c | 93 +++++++++++++++++++++++++++++++++++++------- arch/arm/mach-tegra/pm.h | 15 +++++++ arch/arm/mach-tegra/pmc.c | 50 ++++++++++++++++++++++-- arch/arm/mach-tegra/pmc.h | 4 +- 5 files changed, 146 insertions(+), 17 deletions(-)
arch/arm/mach-tegra/common.c +1 -0
@@ -109,5 +109,6 @@ void __init tegra_init_early(void)void __init tegra_init_late (void ) { +tegra_init_suspend ();tegra_powergate_debugfs_init (); }
arch/arm/mach-tegra/pm.c +80 -13
118 lines not on this page · raw message
arch/arm/mach-tegra/pm.h +15 -0
@@ -21,6 +21,8 @@#ifndef _MACH_TEGRA_PM_H_#define _MACH_TEGRA_PM_H_ +#include "pmc.h" +extern unsigned long l2x0_saved_regs_addr;void save_cpu_arch_register (void );
@@ -32,4 +34,17 @@ bool tegra_set_cpu_in_lp2(int phy_cpu_id);void tegra_idle_lp2_last (u32 cpu_on_time,u32 cpu_off_time);extern void (*tegra_tear_down_cpu)(void ); +#ifdef CONFIG_PM_SLEEP +enum tegra_suspend_mode tegra_pm_validate_suspend_mode ( +enum tegra_suspend_mode mode); +void tegra_init_suspend (void ); +#else +enum tegra_suspend_mode tegra_pm_validate_suspend_mode ( +enum tegra_suspend_mode mode) +{ +return TEGRA_SUSPEND_NONE ; +} +static inline void tegra_init_suspend (void ) {} +#endif +#endif /* _MACH_TEGRA_PM_H_ */
arch/arm/mach-tegra/pmc.c +47 -3
80 lines not on this page · raw message
arch/arm/mach-tegra/pmc.h +3 -1
@@ -27,7 +27,9 @@ enum tegra_suspend_mode { };#ifdef CONFIG_PM_SLEEP -void set_power_timers (unsigned long us_on,unsigned long us_off); +enum tegra_suspend_mode tegra_pmc_get_suspend_mode (void ); +void tegra_pmc_pm_set (enum tegra_suspend_mode mode); +void tegra_pmc_suspend_init (void );#endif bool tegra_pmc_cpu_is_powered (int cpuid);
Signature · 1 line
1.8.2
PATCH v6 5/9 ARM: dts: tegra: add power gpio keys to DT
In reply to Joseph LoThis adds the power gpio key to DT and enable the wakeup of the gpio key for the device. The Seaboard and paz00 already had the power gpio key binding and the power key of Whistler was on KBC. So these boards' device tree didn't include in this patch.
---
V6:
* no change
V5:
* no change
V4:
* no change
V3:
* no change
V2:
* no change
--- arch/arm/boot/dts/tegra20-harmony.dts | 11 +++++++++++ arch/arm/boot/dts/tegra20-trimslice.dts | 11 +++++++++++ arch/arm/boot/dts/tegra20-ventana.dts | 11 +++++++++++ 3 files changed, 33 insertions(+)
arch/arm/boot/dts/tegra20-harmony.dts +11 -0
@@ -464,6 +464,17 @@ }; }; + gpio-keys { + compatible = "gpio-keys"; + + power { + label = "Power"; + gpios = <&gpio 170 1>; /* gpio PV2, active low */ + linux,code = <116>; /* KEY_POWER */ + gpio-key,wakeup; + }; + }; + kbc { status = "okay"; nvidia,debounce-delay-ms = <2>;
arch/arm/boot/dts/tegra20-trimslice.dts +11 -0
@@ -343,6 +343,17 @@ }; }; + gpio-keys { + compatible = "gpio-keys"; + + power { + label = "Power"; + gpios = <&gpio 190 1>; /* gpio PX6, active low */ + linux,code = <116>; /* KEY_POWER */ + gpio-key,wakeup; + }; + }; + poweroff { compatible = "gpio-poweroff"; gpios = <&gpio 191 1>; /* gpio PX7, active low */
arch/arm/boot/dts/tegra20-ventana.dts +11 -0
@@ -544,6 +544,17 @@ }; }; + gpio-keys { + compatible = "gpio-keys"; + + power { + label = "Power"; + gpios = <&gpio 170 1>; /* gpio PV2, active low */ + linux,code = <116>; /* KEY_POWER */ + gpio-key,wakeup; + }; + }; + regulators { compatible = "simple-bus"; #address-cells = <1>;
Signature · 1 line
1.8.2
PATCH v6 6/9 ARM: dts: tegra: whistler: add wakeup source for KBC
In reply to Joseph LoAdding KBC as a wakeup source for Whistler board.
---
V6:
* no change
V5:
* no change
V4:
* no change
V3:
* no change
V2:
* no change
--- arch/arm/boot/dts/tegra20-whistler.dts | 1 + 1 file changed, 1 insertion(+)
arch/arm/boot/dts/tegra20-whistler.dts +1 -0
@@ -539,6 +539,7 @@ nvidia,repeat-delay-ms = <160>; nvidia,kbc-row-pins = <0 1 2>; nvidia,kbc-col-pins = <16 17>; + nvidia,wakeup-source; linux,keymap = <0x00000074 /* KEY_POWER */ 0x01000066 /* KEY_HOME */ 0x0101009E /* KEY_BACK */
Signature · 1 line
1.8.2
PATCH v6 7/9 ARM: dts: tegra: add non-removable and keep-power-in-suspend property for MMC
In reply to Joseph LoThis patch adds "non-removable" property of MMC host where the eMMC device is for Tegra platform.
And the "keep-power-in-suspend" property was used for the SDIO device that need this to go into suspend mode (e.g. BRCM43xx series).
---
V6:
* add "non-removable" property for Dalmore
V5:
* no change
V4:
* no change
V3:
* no change
V2:
* no change
--- arch/arm/boot/dts/tegra114-dalmore.dts | 1 + arch/arm/boot/dts/tegra20-paz00.dts | 1 + arch/arm/boot/dts/tegra20-seaboard.dts | 2 ++ arch/arm/boot/dts/tegra20-ventana.dts | 2 ++ arch/arm/boot/dts/tegra20-whistler.dts | 1 + arch/arm/boot/dts/tegra30-beaver.dts | 1 + arch/arm/boot/dts/tegra30-cardhu-a02.dts | 1 + arch/arm/boot/dts/tegra30-cardhu-a04.dts | 1 + arch/arm/boot/dts/tegra30-cardhu.dtsi | 1 + 9 files changed, 11 insertions(+)
arch/arm/boot/dts/tegra114-dalmore.dts +1 -0
@@ -837,6 +837,7 @@ sdhci at 78000600 { bus-width = <8>; status = "okay"; + non-removable; }; clocks {
arch/arm/boot/dts/tegra20-paz00.dts +1 -0
@@ -445,6 +445,7 @@ sdhci at c8000600 { status = "okay"; bus-width = <8>; + non-removable; }; clocks {
arch/arm/boot/dts/tegra20-seaboard.dts +2 -0
@@ -580,6 +580,7 @@ status = "okay"; power-gpios = <&gpio 86 0>; /* gpio PK6 */ bus-width = <4>; + keep-power-in-suspend; }; sdhci at c8000400 {
@@ -593,6 +594,7 @@ sdhci at c8000600 { status = "okay"; bus-width = <8>; + non-removable; }; clocks {
arch/arm/boot/dts/tegra20-ventana.dts +2 -0
@@ -516,6 +516,7 @@ status = "okay"; power-gpios = <&gpio 86 0>; /* gpio PK6 */ bus-width = <4>; + keep-power-in-suspend; }; sdhci at c8000400 {
@@ -529,6 +530,7 @@ sdhci at c8000600 { status = "okay"; bus-width = <8>; + non-removable; }; clocks {
arch/arm/boot/dts/tegra20-whistler.dts +1 -0
@@ -518,6 +518,7 @@ sdhci at c8000600 { status = "okay"; bus-width = <8>; + non-removable; }; clocks {
arch/arm/boot/dts/tegra30-beaver.dts +1 -0
@@ -266,6 +266,7 @@ sdhci at 78000600 { status = "okay"; bus-width = <8>; + non-removable; }; clocks {
arch/arm/boot/dts/tegra30-cardhu-a02.dts +1 -0
@@ -88,6 +88,7 @@ status = "okay"; power-gpios = <&gpio 28 0>; /* gpio PD4 */ bus-width = <4>; + keep-power-in-suspend; }; };
arch/arm/boot/dts/tegra30-cardhu-a04.dts +1 -0
@@ -100,5 +100,6 @@ status = "okay"; power-gpios = <&gpio 27 0>; /* gpio PD3 */ bus-width = <4>; + keep-power-in-suspend; }; };
arch/arm/boot/dts/tegra30-cardhu.dtsi +1 -0
@@ -320,6 +320,7 @@ sdhci at 78000600 { status = "okay"; bus-width = <8>; + non-removable; }; clocks {
Signature · 1 line
1.8.2
PATCH v6 8/9 ARM: tegra: config: defconfig update
In reply to Joseph LoKEYBOARD_GPIO:
* Enable gpio-key driver
---
V6:
* no change
V5:
* no change
V4:
* no change
V3:
* no change
V2:
* no change
--- arch/arm/configs/tegra_defconfig | 1 + 1 file changed, 1 insertion(+)
arch/arm/configs/tegra_defconfig +1 -0
@@ -106,6 +106,7 @@ CONFIG_RT2X00=y CONFIG_RT2800USB=m CONFIG_INPUT_EVDEV=y CONFIG_KEYBOARD_TEGRA=y +CONFIG_KEYBOARD_GPIO=y CONFIG_INPUT_MISC=y CONFIG_INPUT_MPU3050=y # CONFIG_LEGACY_PTYS is not set
Signature · 1 line
1.8.2
PATCH v6 9/9 ARM: dts: tegra: add the PM configurations of PMC
In reply to Joseph LoAdding the PM configuration of PMC when the platform support suspend function.
---
V6:
* add support for colibri and tamonten based board V5:
* no change
V4:
* no change
V3:
* fix the configuration for paz00 board V2:
* no change
--- arch/arm/boot/dts/tegra20-colibri-512.dtsi | 9 +++++++++ arch/arm/boot/dts/tegra20-harmony.dts | 6 ++++++ arch/arm/boot/dts/tegra20-paz00.dts | 6 ++++++ arch/arm/boot/dts/tegra20-seaboard.dts | 6 ++++++ arch/arm/boot/dts/tegra20-tamonten.dtsi | 6 ++++++ arch/arm/boot/dts/tegra20-trimslice.dts | 9 +++++++++ arch/arm/boot/dts/tegra20-ventana.dts | 6 ++++++ arch/arm/boot/dts/tegra20-whistler.dts | 8 ++++++++ arch/arm/boot/dts/tegra30-beaver.dts | 7 +++++++ arch/arm/boot/dts/tegra30-cardhu.dtsi | 7 +++++++ 10 files changed, 70 insertions(+)
arch/arm/boot/dts/tegra20-colibri-512.dtsi +9 -0
@@ -361,6 +361,15 @@ }; }; + pmc { + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <5000>; + nvidia,cpu-pwr-off-time = <5000>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <3875>; + nvidia,sys-clock-req-active-high; + }; + memory-controller at 7000f400 { emc-table at 83250 { reg = <83250>;
arch/arm/boot/dts/tegra20-harmony.dts +6 -0
@@ -416,6 +416,12 @@ pmc { nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <5000>; + nvidia,cpu-pwr-off-time = <5000>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <3875>; + nvidia,sys-clock-req-active-high; }; usb at c5000000 {
arch/arm/boot/dts/tegra20-paz00.dts +6 -0
@@ -415,6 +415,12 @@ pmc { nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <2000>; + nvidia,cpu-pwr-off-time = <0>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <0>; + nvidia,sys-clock-req-active-high; }; usb at c5000000 {
arch/arm/boot/dts/tegra20-seaboard.dts +6 -0
@@ -517,6 +517,12 @@ pmc { nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <5000>; + nvidia,cpu-pwr-off-time = <5000>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <3875>; + nvidia,sys-clock-req-active-high; }; memory-controller at 7000f400 {
arch/arm/boot/dts/tegra20-tamonten.dtsi +6 -0
@@ -458,6 +458,12 @@ pmc { nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <5000>; + nvidia,cpu-pwr-off-time = <5000>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <3875>; + nvidia,sys-clock-req-active-high; }; usb at c5008000 {
arch/arm/boot/dts/tegra20-trimslice.dts +9 -0
@@ -300,6 +300,15 @@ }; }; + pmc { + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <5000>; + nvidia,cpu-pwr-off-time = <5000>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <3875>; + nvidia,sys-clock-req-active-high; + }; + usb at c5000000 { status = "okay"; nvidia,vbus-gpio = <&gpio 170 0>; /* gpio PV2 */
arch/arm/boot/dts/tegra20-ventana.dts +6 -0
@@ -493,6 +493,12 @@ pmc { nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <2000>; + nvidia,cpu-pwr-off-time = <100>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <458>; + nvidia,sys-clock-req-active-high; }; usb at c5000000 {
arch/arm/boot/dts/tegra20-whistler.dts +8 -0
@@ -496,6 +496,14 @@ pmc { nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <2000>; + nvidia,cpu-pwr-off-time = <1000>; + nvidia,core-pwr-good-time = <0 3845>; + nvidia,core-pwr-off-time = <93727>; + nvidia,core-power-req-active-high; + nvidia,sys-clock-req-active-high; + nvidia,combined-power-req; }; usb at c5000000 {
arch/arm/boot/dts/tegra30-beaver.dts +7 -0
@@ -253,6 +253,13 @@ pmc { status = "okay"; nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <2000>; + nvidia,cpu-pwr-off-time = <200>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <0>; + nvidia,core-power-req-active-high; + nvidia,sys-clock-req-active-high; }; sdhci at 78000000 {
arch/arm/boot/dts/tegra30-cardhu.dtsi +7 -0
@@ -307,6 +307,13 @@ pmc { status = "okay"; nvidia,invert-interrupt; + nvidia,suspend-mode = <2>; + nvidia,cpu-pwr-good-time = <2000>; + nvidia,cpu-pwr-off-time = <200>; + nvidia,core-pwr-good-time = <3845 3845>; + nvidia,core-pwr-off-time = <0>; + nvidia,core-power-req-active-high; + nvidia,sys-clock-req-active-high; }; sdhci at 78000000 {
Signature · 1 line
1.8.2
v6 cover ARM: tegra: add platform suspend support
In reply to Joseph LoQuoted 5 lines · Joseph Lo
This series introduces a basic functionality for Tegra to support the platform suspend and resume.
Note: This series only adds the support for Tegra20 and Tegra30. The Tegra114 will be supported later.
The series is applied.
Patches 1-4 to Tegra's for-3.10/soc branch. Patches 5-7, 9 to Tegra's for-3.10/dt branch. Patch 8 squashed into Tegra's for-3.10/defconfig branch.