ArchosG9: add keyboard input and new reset menu entries (v3)
Subsystems (2)
PATCH 1/1 ArchosG9: add keyboard input and new reset menu entries (v3)
This is the third version of this patch series. It only includes the only unapplied patch with all modifications from feedback, thanks Sascha.
Vicente Bergas (1):
OMAP4: add command to select next boot device priority
arch/arm/mach-omap/Makefile | 1 + arch/arm/mach-omap/boot_order.c | 83 +++++++++++++++++++++++++ arch/arm/mach-omap/include/mach/omap4-silicon.h | 20 ++++++ arch/arm/mach-omap/omap4_generic.c | 20 ++++++ commands/Kconfig | 7 +++ 5 files changed, 131 insertions(+) create mode 100644 arch/arm/mach-omap/boot_order.c
Signature · 7 lines
1.8.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH 1/1 OMAP4: add command to select next boot device priority
On OMAP4 SoC there is a SAR memory region (Save & Rescue) where the ROM code reads the device to boot from. This patch adds a way to set this.
--- arch/arm/mach-omap/Makefile | 1 + arch/arm/mach-omap/boot_order.c | 83 +++++++++++++++++++++++++ arch/arm/mach-omap/include/mach/omap4-silicon.h | 20 ++++++ arch/arm/mach-omap/omap4_generic.c | 20 ++++++ commands/Kconfig | 7 +++ 5 files changed, 131 insertions(+) create mode 100644 arch/arm/mach-omap/boot_order.c
arch/arm/mach-omap/Makefile +1 -0
@@ -30,4 +30,5 @@ obj-$(CONFIG_OMAP_GPMC) += gpmc.o devices-gpmc-nand.o obj-$(CONFIG_SHELL_NONE) += xload.o obj-$(CONFIG_MFD_TWL6030) += omap4_twl6030_mmc.o obj-$(CONFIG_OMAP4_USBBOOT) += omap4_rom_usb.o +obj-$(CONFIG_CMD_BOOT_ORDER) += boot_order.o obj-y += gpio.o
arch/arm/mach-omap/boot_order.c new file +83 -0
83 lines not on this page · raw message
arch/arm/mach-omap/include/mach/omap4-silicon.h +20 -0
@@ -161,6 +161,25 @@#define OMAP44XX_PRM_RSTCTRL_RESET 0x01/* +* SAR (Save & Rescue) memory region +*/ +#define OMAP44XX_SAR_RAM_BASE 0x4a326000 +#define OMAP44XX_SAR_CH_ADDRESS (OMAP44XX_SAR_RAM_BASE + 0xA00) +#define OMAP44XX_SAR_CH_START (OMAP44XX_SAR_RAM_BASE + 0xA0C) +#define OMAP44XX_SAR_BOOT_VOID 0x00 +#define OMAP44XX_SAR_BOOT_XIP 0x01 +#define OMAP44XX_SAR_BOOT_XIPWAIT 0x02 +#define OMAP44XX_SAR_BOOT_NAND 0x03 +#define OMAP44XX_SAR_BOOT_ONENAND 0x04 +#define OMAP44XX_SAR_BOOT_MMC1 0x05 +#define OMAP44XX_SAR_BOOT_MMC2_1 0x06 +#define OMAP44XX_SAR_BOOT_MMC2_2 0x07 +#define OMAP44XX_SAR_BOOT_UART 0x43 +#define OMAP44XX_SAR_BOOT_USB_1 0x45 +#define OMAP44XX_SAR_BOOT_USB_ULPI 0x46 +#define OMAP44XX_SAR_BOOT_USB_2 0x47 + +/* * Non-secure SRAM Addresses * Non-secure RAM starts at 0x40300000 for GP devices. But we keep SRAM_BASE * at 0x40304000(EMU base) so that our code works for both EMU and GP
@@ -212,6 +231,7 @@ void omap4_ddr_init(const struct ddr_regs *, const struct dpll_param *);void omap4_power_i2c_send (u32 );unsigned int omap4_revision (void ); noinline int omap4_scale_vcores(unsigned vsel0_pin); +void omap4_set_warmboot_order (u32 *device_list);#endif
arch/arm/mach-omap/omap4_generic.c +20 -0
@@ -41,6 +41,26 @@ void __noreturn reset_cpu(unsigned long addr)while (1 ); } +void omap4_set_warmboot_order (u32 *device_list) +{ +const u32 CH [] = { +0xCF00AA01 , +0x0000000C , + (device_list[0 ] <<16 ) |0x0000 , + (device_list[2 ] <<16 ) | device_list[1 ], +0x0000 | device_list[3 ], +0x00000000 , +0x00000000 , +0x00000000 , +0x00000000 + }; +int i; + +for (i =0 ; i <ARRAY_SIZE (CH ); i++) +writel (CH [i],OMAP44XX_SAR_CH_START + i*sizeof (CH [0 ])); +writel (OMAP44XX_SAR_CH_START ,OMAP44XX_SAR_CH_ADDRESS ); +} +#define WATCHDOG_WSPR 0x48#define WATCHDOG_WWPS 0x34
commands/Kconfig +7 -0
@@ -474,6 +474,13 @@ config CMD_POWEROFF depends on HAS_POWEROFF prompt "poweroff" +config CMD_BOOT_ORDER + tristate + depends on ARCH_OMAP4 + prompt "boot_order" + help + A command to choose the next boot device on a warm reset. + config CMD_GO tristate prompt "go"
Signature · 7 lines
1.8.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH] OMAP4: add command to select next boot device priority
Quoted 187 lines · Vicente Bergas
On OMAP4 SoC there is a SAR memory region (Save & Rescue) where the ROM code reads the device to boot from. This patch adds a way to set this.
Signed-off-by Vicente Bergas <[email protected]>--- arch/arm/mach-omap/Makefile | 1 + arch/arm/mach-omap/boot_order.c | 83 +++++++++++++++++++++++++ arch/arm/mach-omap/include/mach/omap4-silicon.h | 20 ++++++ arch/arm/mach-omap/omap4_generic.c | 20 ++++++ commands/Kconfig | 7 +++ 5 files changed, 131 insertions(+) create mode 100644 arch/arm/mach-omap/boot_order.carch/arm/mach-omap/Makefile +1
-0@@ -30,4 +30,5 @@ obj-$(CONFIG_OMAP_GPMC) += gpmc.o devices-gpmc-nand.o obj-$(CONFIG_SHELL_NONE) += xload.o obj-$(CONFIG_MFD_TWL6030) += omap4_twl6030_mmc.o obj-$(CONFIG_OMAP4_USBBOOT) += omap4_rom_usb.o +obj-$(CONFIG_CMD_BOOT_ORDER) += boot_order.o obj-y += gpio.oarch/arm/mach-omap/boot_order.c new file +83
-0@@ -0,0 +1,83 @@ +/* +* boot_order.c - configure omap warm boot +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 +* as published by the Free Software Foundation. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +*/ + +#include <common.h> +#include <command.h> +#include <complete.h> +#include <mach/omap4-silicon.h> + +struct bootsrc { +const char *name; +uint32_t sar; +}; + +const struct bootsrc src_list[] = { + {"xip" ,OMAP44XX_SAR_BOOT_XIP }, + {"xipwait" ,OMAP44XX_SAR_BOOT_XIPWAIT }, + {"nand" ,OMAP44XX_SAR_BOOT_NAND }, + {"onenand" ,OMAP44XX_SAR_BOOT_ONENAND }, + {"mmc1" ,OMAP44XX_SAR_BOOT_MMC1 }, + {"mmc2_1" ,OMAP44XX_SAR_BOOT_MMC2_1 }, + {"mmc2_2" ,OMAP44XX_SAR_BOOT_MMC2_2 }, + {"uart" ,OMAP44XX_SAR_BOOT_UART }, + {"usb_1" ,OMAP44XX_SAR_BOOT_USB_1 }, + {"usb_ulpi" ,OMAP44XX_SAR_BOOT_USB_ULPI }, + {"usb_2" ,OMAP44XX_SAR_BOOT_USB_2 }, +}; + +static uint32_t parse_device (char *str) +{ +int i; + +for (i =0 ; i <ARRAY_SIZE (src_list); i++) { +if (strcmp (str, src_list[i].name) ==0 ) +return src_list[i].sar; + } +printf ("Unknown device '%s'\n" , str); +return OMAP44XX_SAR_BOOT_VOID ; +} + +static int cmd_boot_order (int argc,char *argv[]) +{ +uint32_t device_list[] = { +OMAP44XX_SAR_BOOT_VOID , +OMAP44XX_SAR_BOOT_VOID , +OMAP44XX_SAR_BOOT_VOID , +OMAP44XX_SAR_BOOT_VOID , + }; +int i; + +if (argc <2 ) +return COMMAND_ERROR_USAGE ; +for (i =0 ; i +1 < argc && i <ARRAY_SIZE (device_list); i++) { + device_list[i] =parse_device (argv[i +1 ]); +if (device_list[i] ==OMAP44XX_SAR_BOOT_VOID ) +return COMMAND_ERROR_USAGE ; + } +omap4_set_warmboot_order (device_list); +return 0 ; +} + +static const __maybe_unused char cmd_boot_order_help[] = +"Usage: boot_order <device 1> [<device n>]\n" +"Set warm boot order of up to four devices.\n" +"Each device can be one of:\n" +"xip xipwait nand onenand mmc1 mmc2_1 mmc2_2 uart usb_1 usb_ulpi usb_2\n" ; + +BAREBOX_CMD_START (boot_order) + .cmd = cmd_boot_order, + .usage = "boot_order <device 1> [<device n>]", + BAREBOX_CMD_HELP(cmd_boot_order_help) + BAREBOX_CMD_COMPLETE(empty_complete) +BAREBOX_CMD_END arch/arm/mach-omap/include/mach/omap4-silicon.h +20
-0@@ -161,6 +161,25 @@#define OMAP44XX_PRM_RSTCTRL_RESET 0x01/* +* SAR (Save & Rescue) memory region +*/ +#define OMAP44XX_SAR_RAM_BASE 0x4a326000 +#define OMAP44XX_SAR_CH_ADDRESS (OMAP44XX_SAR_RAM_BASE + 0xA00) +#define OMAP44XX_SAR_CH_START (OMAP44XX_SAR_RAM_BASE + 0xA0C) +#define OMAP44XX_SAR_BOOT_VOID 0x00 +#define OMAP44XX_SAR_BOOT_XIP 0x01 +#define OMAP44XX_SAR_BOOT_XIPWAIT 0x02 +#define OMAP44XX_SAR_BOOT_NAND 0x03 +#define OMAP44XX_SAR_BOOT_ONENAND 0x04 +#define OMAP44XX_SAR_BOOT_MMC1 0x05 +#define OMAP44XX_SAR_BOOT_MMC2_1 0x06 +#define OMAP44XX_SAR_BOOT_MMC2_2 0x07 +#define OMAP44XX_SAR_BOOT_UART 0x43 +#define OMAP44XX_SAR_BOOT_USB_1 0x45 +#define OMAP44XX_SAR_BOOT_USB_ULPI 0x46 +#define OMAP44XX_SAR_BOOT_USB_2 0x47 + +/* * Non-secure SRAM Addresses * Non-secure RAM starts at 0x40300000 for GP devices. But we keep SRAM_BASE * at 0x40304000(EMU base) so that our code works for both EMU and GP @@ -212,6 +231,7 @@ void omap4_ddr_init(const struct ddr_regs *, const struct dpll_param *);void omap4_power_i2c_send (u32 );unsigned int omap4_revision (void ); noinline int omap4_scale_vcores(unsigned vsel0_pin); +void omap4_set_warmboot_order (u32 *device_list);#endif arch/arm/mach-omap/omap4_generic.c +20
-0@@ -41,6 +41,26 @@ void __noreturn reset_cpu(unsigned long addr)while (1 ); } +void omap4_set_warmboot_order (u32 *device_list) +{ +const u32 CH [] = { +0xCF00AA01 , +0x0000000C , + (device_list[0 ] <<16 ) |0x0000 , + (device_list[2 ] <<16 ) | device_list[1 ], +0x0000 | device_list[3 ], +0x00000000 , +0x00000000 , +0x00000000 , +0x00000000 + }; +int i; + +for (i =0 ; i <ARRAY_SIZE (CH ); i++) +writel (CH [i],OMAP44XX_SAR_CH_START + i*sizeof (CH [0 ])); +writel (OMAP44XX_SAR_CH_START ,OMAP44XX_SAR_CH_ADDRESS ); +} +#define WATCHDOG_WSPR 0x48#define WATCHDOG_WWPS 0x34commands/Kconfig +0
-0
commands/Kconfig config CMD_POWEROFF · line 483
Quoted 10 lines
commands/Kconfig +7
-0@@ -474,6 +474,13 @@ config CMD_POWEROFF depends on HAS_POWEROFF prompt "poweroff" +config CMD_BOOT_ORDER + tristate + depends on ARCH_OMAP4 + prompt "boot_order" + help + A command to choose the next boot device on a warm reset. +
Please move the config option to arch/arm/mach-omap/ also.
Otherwise looks good.
Sascha
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox