ARM: mx28: add auart2 2 pins pinmux to imx28.dtsi
Subsystems (2)
PATCH 1/3 ARM: mx28: add auart2 2 pins pinmux to imx28.dtsi
Add auart2 2 pins configuration on its main pads
Signed-off-by Eric B?nard <[email protected]>
--- arch/arm/boot/dts/imx28.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)
arch/arm/boot/dts/imx28.dtsi +11 -0
@@ -308,6 +308,17 @@ fsl,pull-up = <0>; }; + auart2_2pins_b: auart2-2pins at 1 { + reg = <1>; + fsl,pinmux-ids = < + 0x3080 /* MX28_PAD_AUART2_RX__AUART2_RX */ + 0x3090 /* MX28_PAD_AUART2_TX__AUART2_TX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + auart3_pins_a: auart3 at 0 { reg = <0>; fsl,pinmux-ids = <
Signature · 1 line
1.7.11.7
PATCH 2/3 ARM: mx28: add auart3 2 pins pinmux to imx28.dtsi
Add auart3 2 pins configuration on its main pads
Signed-off-by Eric B?nard <[email protected]>
--- arch/arm/boot/dts/imx28.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)
arch/arm/boot/dts/imx28.dtsi +11 -0
@@ -343,6 +343,17 @@ fsl,pull-up = <0>; }; + auart3_2pins_b: auart3-2pins at 1 { + reg = <1>; + fsl,pinmux-ids = < + 0x30c0 /* MX28_PAD_AUART3_RX__AUART3_RX */ + 0x30d0 /* MX28_PAD_AUART3_TX__AUART3_TX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + mac0_pins_a: mac0 at 0 { reg = <0>; fsl,pinmux-ids = <
Signature · 1 line
1.7.11.7
PATCH 3/3 ARM: mx28: add auart4 2 pins pinmux to imx28.dtsi
In reply to Eric BénardAdd auart4 2 pins configuration on SSP3 pads
Signed-off-by Eric B?nard <[email protected]>
--- arch/arm/boot/dts/imx28.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)
arch/arm/boot/dts/imx28.dtsi +11 -0
@@ -354,6 +354,17 @@ fsl,pull-up = <0>; }; + auart4_2pins_a: auart4 at 0 { + reg = <0>; + fsl,pinmux-ids = < + 0x2181 /* MX28_PAD_SSP3_SCK__AUART4_TX */ + 0x2191 /* MX28_PAD_SSP3_MOSI__AUART4_RX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + mac0_pins_a: mac0 at 0 { reg = <0>; fsl,pinmux-ids = <
Signature · 1 line
1.7.11.7
Quoted 3 lines · Eric Bénard
Add auart2 2 pins configuration on its main pads
Signed-off-by Eric Bénard <[email protected]>
All 3 patches applied, thanks.
Quoted 29 lines
--- arch/arm/boot/dts/imx28.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)arch/arm/boot/dts/imx28.dtsi +11
-0@@ -308,6 +308,17 @@ fsl,pull-up = <0>; }; + auart2_2pins_b: auart2-2pins@1 { + reg = <1>; + fsl,pinmux-ids = < + 0x3080 /* MX28_PAD_AUART2_RX__AUART2_RX */ + 0x3090 /* MX28_PAD_AUART2_TX__AUART2_TX */ + >; + fsl,drive-strength = <0>; + fsl,voltage = <1>; + fsl,pull-up = <0>; + }; + auart3_pins_a: auart3@0 { reg = <0>; fsl,pinmux-ids = <Signature · 1 line
1.7.11.7