ARM: mach-imx6q: Remove code for setting up cko clock
Subsystems (3)
Fabio Estevam
reviewerPATCH 1/1 ARM: mach-imx6q: Remove code for setting up cko clock
From: Fabio Estevam <[email protected]>
Let the bootloader setup the cko clock that drives the audio codec.
This simplifies a lot the code and when a new board needs to add audio support, it will not have to add all this amount of code again.
--- arch/arm/mach-imx/mach-imx6q.c | 25 ------------------------- 1 file changed, 25 deletions(-)
arch/arm/mach-imx/mach-imx6q.c +0 -25
@@ -113,36 +113,11 @@ static int ksz9021rn_phy_fixup(struct phy_device *phydev)return 0 ; } -static void __init imx6q_sabrelite_cko1_setup (void ) -{ -struct clk *cko1_sel, *ahb, *cko1; -unsigned long rate; - - cko1_sel =clk_get_sys (NULL ,"cko1_sel" ); - ahb =clk_get_sys (NULL ,"ahb" ); - cko1 =clk_get_sys (NULL ,"cko1" ); -if (IS_ERR (cko1_sel) ||IS_ERR (ahb) ||IS_ERR (cko1)) { -pr_err ("cko1 setup failed!\n" ); - goto put_clk; - } -clk_set_parent (cko1_sel, ahb); - rate =clk_round_rate (cko1,16000000 ); -clk_set_rate (cko1, rate); -put_clk: -if (!IS_ERR (cko1_sel)) -clk_put (cko1_sel); -if (!IS_ERR (ahb)) -clk_put (ahb); -if (!IS_ERR (cko1)) -clk_put (cko1); -} -static void __init imx6q_sabrelite_init (void ) {if (IS_BUILTIN (CONFIG_PHYLIB ))phy_register_fixup_for_uid (PHY_ID_KSZ9021 ,MICREL_PHY_ID_MASK , ksz9021rn_phy_fixup); -imx6q_sabrelite_cko1_setup (); }static void __init imx6q_1588_init (void )
Signature · 1 line
1.7.9.5
Sascha Hauer
maintainerPATCH 1/1 ARM: mach-imx6q: Remove code for setting up cko clock
Quoted 4 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Let the bootloader setup the cko clock that drives the audio codec.
I really don't like such stuff. Where is documented what's expected from the bootloader? Which versions of which bootloader do implement this?
The code you remove is not particularly nice, but just removing it is no solution to the problem.
Quoted 2 lines
This simplifies a lot the code and when a new board needs to add audio support, it will not have to add all this amount of code again.
It shouldn't be necessary to duplicate the code for each board.
Sascha
Quoted 51 lines
Signed-off-by Fabio Estevam <[email protected]>--- arch/arm/mach-imx/mach-imx6q.c | 25 ------------------------- 1 file changed, 25 deletions(-)arch/arm/mach-imx/mach-imx6q.c +0
-25@@ -113,36 +113,11 @@ static int ksz9021rn_phy_fixup(struct phy_device *phydev)return 0 ; } -static void __init imx6q_sabrelite_cko1_setup (void ) -{ -struct clk *cko1_sel, *ahb, *cko1; -unsigned long rate; - - cko1_sel =clk_get_sys (NULL ,"cko1_sel" ); - ahb =clk_get_sys (NULL ,"ahb" ); - cko1 =clk_get_sys (NULL ,"cko1" ); -if (IS_ERR (cko1_sel) ||IS_ERR (ahb) ||IS_ERR (cko1)) { -pr_err ("cko1 setup failed!\n" ); - goto put_clk; - } -clk_set_parent (cko1_sel, ahb); - rate =clk_round_rate (cko1,16000000 ); -clk_set_rate (cko1, rate); -put_clk: -if (!IS_ERR (cko1_sel)) -clk_put (cko1_sel); -if (!IS_ERR (ahb)) -clk_put (ahb); -if (!IS_ERR (cko1)) -clk_put (cko1); -} -static void __init imx6q_sabrelite_init (void ) {if (IS_BUILTIN (CONFIG_PHYLIB ))phy_register_fixup_for_uid (PHY_ID_KSZ9021 ,MICREL_PHY_ID_MASK , ksz9021rn_phy_fixup); -imx6q_sabrelite_cko1_setup (); }static void __init imx6q_1588_init (void )Signature · 1 line
1.7.9.5
Signature · 4 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Fabio Estevam
reviewerPATCH 1/1 ARM: mach-imx6q: Remove code for setting up cko clock
Hi Sascha,
Quoted 8 lines · Sascha Hauer
Quoted 4 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Let the bootloader setup the cko clock that drives the audio codec.
I really don't like such stuff. Where is documented what's expected from the bootloader? Which versions of which bootloader do implement this?
As far as I know such documentation does not exist. It would be nice to have it, especially now that
we are recently moving some ARM errata stuff out of the multi plaform kernel.
I sent patches today for enabling CLKO for sabrelite in Barebox and U-boot.
Quoted 2 lines
The code you remove is not particularly nice, but just removing it is no solution to the problem.
Please let me know what is your preferred solution then.
There was some discussion here:
https://patchwork.kernel.org/patch/2303011/
,but I didn't see this come into any conclusion of what is the preferred way to handle this.
Quoted 5 lines
Quoted 3 lines
This simplifies a lot the code and when a new board needs to add audio support, it will not have to add all this amount of code again.
It shouldn't be necessary to duplicate the code for each board.
Yes, some code could be factored out, but every time we need to add audio support for a new board we would need to keep polluting arch/arm/mach-imx/mach-imx6q.c with things like:
if (of_machine_is_compatible("fsl,imx6q-xxx"))
cko_setup()
Regards,
Fabio Estevam
Sascha Hauer
maintainerPATCH 1/1 ARM: mach-imx6q: Remove code for setting up cko clock
Quoted 9 lines · Fabio Estevam
Hi Sascha,
Quoted 6 lines · Sascha Hauer
Quoted 4 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Let the bootloader setup the cko clock that drives the audio codec.
Quoted 6 lines
Quoted 2 lines
I really don't like such stuff. Where is documented what's expected from the bootloader? Which versions of which bootloader do implement this?
As far as I know such documentation does not exist. It would be nice to have it, especially now that
we are recently moving some ARM errata stuff out of the multi plaform kernel.
Yes, that's another thing that should be documented. Without even documenting it we go into an area where things happen to work in certain combinations and we won't have good answers when somebody asks on the list why something doesn't work for him (other than: update your bootloader and see if that helps)
Quoted 6 lines
I sent patches today for enabling CLKO for sabrelite in Barebox and U-boot.
Quoted 2 lines
The code you remove is not particularly nice, but just removing it is no solution to the problem.
Quoted 7 lines
Please let me know what is your preferred solution then.
There was some discussion here:
https://patchwork.kernel.org/patch/2303011/,but I didn't see this come into any conclusion of what is the preferred way to handle this.
It may seemed like I bashed upon putting configuration data in the devicetree. This wasn't really my intention, I more hoped that there would be some more discussion about this topic.
I still think that it's a bad idea to just mix the configuration data with the hardware description, because the hardware doesn't change, but the confguration data is a matter of usecase and sometimes even personal taste.
I also think that the devicetree format as such is a good format to describe such (hardware specific) configuration data.
I'm perfectly fine with having configuration data in the devicetree, but there should be some strict rules:
- configuration data should be in a separate source dts
- configuration data should be in a separate subtree (/chosen)
- configuration data should *not* be in the board dts files in the kernel.
- ideally it should be possible to distribute configuration data and hardware description separately. hardware description doesn't change (as long as we don't change the bindings of course), but configuration data often changes with the usecase or kernel version.
Particularly currently the dts files in the Kernel often enforce a partition layout for mtd devices. Such things shouldn't happen.
Quoted 5 lines
Quoted 5 lines
Quoted 4 lines
This simplifies a lot the code and when a new board needs to add audio support, it will not have to add all this amount of code again.
Quoted 8 lines
Quoted 1 line
It shouldn't be necessary to duplicate the code for each board.
Yes, some code could be factored out, but every time we need to add audio support for a new board we would need to keep polluting
arch/arm/mach-imx/mach-imx6q.cwith things like:if (
of_machine_is_compatible("fsl,imx6q-xxx"))cko_setup()
We already have the necessary bindings to encode that the SGTL5000 clock parent is the CLKO pin. That's hardware description and nobody would object to that. That would only leave the problem of finding the correct parent.
Sascha
Signature · 4 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
A message that is not in the archive (sent off-list or not yet received): CAKGA1bnMUBhXdsfOsBOm2T2VA=FHDWHthbPcXqA7eHX1DPJvkw@mail.gmail.com
PATCH 1/1 ARM: mach-imx6q: Remove code for setting up cko clock
Resending to LAKML in plaintext (Google ARGH..), apologies for anyone receiving it twice..
--
Matt Sealey <[email protected]>
Product Development Analyst, Genesi USA, Inc.
Quoted 104 lines · Matt Sealey
Quoted 9 lines · Sascha Hauer
Quoted 4 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Let the bootloader setup the cko clock that drives the audio codec.
I really don't like such stuff. Where is documented what's expected from the bootloader?
Schematics for the board - and basically a flat-out recommendation that all clocks that need to be set to something other than power-on defaults need to be set to their expected parents and rates at bootloader time even if they're not used by the bootloader, unless they can be confirmed totally unused (in which case, they needn't even be in the device tree and Linux will just never know they even exist).
This is a fact of life.. I don't see why Linux should end up with a bunch of board-specific hacks to work around broken bootloaders when we're talking about DT-supported boards. In this case, probably everyone has to go get a new U-Boot anyway to even boot a kernel that would show this problem (no Freescale board ever shipped before 2012 with a dt-capable U-Boot, so unless you're using
DTB_APPEND..).Quoted 11 lines
Which versions of which bootloader do implement this?
The code you remove is not particularly nice, but just removing it is no solution to the problem.
Quoted 3 lines
This simplifies a lot the code and when a new board needs to add audio support,
it will not have to add all this amount of code again.It shouldn't be necessary to duplicate the code for each board.
But it usually is - even if there is a generic "set up clko" routine where you pass a parent and a desired rate, a bunch of boards will end up calling it, and in the end it's basically a workaround for the fact that the bootloader did NOT set this up (when it should!)
For an audio codec, this rate is basically nearly always fixed (and where it isn't.. it's up to the codec driver to
set_rateon it's specified clock when it needs to). Since it isn't possible to dictate clock frequency in the device tree right now, and I at least would prefer that we didn't store "yet to be configured, please assure this" kind of directives in device tree, the bootloader is the best place.There's similar code in MX5 platforms right now which reparents the USB PHY clock to one that can actually can generate desired rates for USB PHYs (which is coordinated with some other code which sets the USB PHY rate inside the PHY). In any case here, all MX5 chips boot with an "impossible" USB PHY configuration (there is no clock parent that can give it that rate, it must be changed), and it is not possible to use the default parent to generate two of the other rates either. This is a bootloader thing for sure. Linux should not be working around this. There's also code that sets parents for eSDHC controllers; this is global code run on every board, and only works because every board designer - so far - didn't bother to do something different (as it stands, the eSDHC gets a reaaaally weird rate because of it, and it is surprising nobody noticed..)
Even if we had such directives in DT, 99.9% of it would be reproduction of clock setting code in bootloader being dumped into the device tree and re-set by Linux yet again. That can cause glitches which can cause devices like codecs to basically go into indeterminate states (and some of these devices simply don't have resets, so they stay in those states unless powered off and on again, and sometimes the regulators aren't configurable - all this is in the schematics for the board if they're available).
When your Linux kernel warns (and it should warn in each driver that detects a weirdo clock scenario that can detect it) that you may need a new bootloader, then updating the bootloader is necessary. For boards where the developers don't like you to update the bootloader, well.. ours are a couple of those, and to be honest, I will happily ship firmware updates when there's some platform support for our board, which I've still not gotten round to doing yet (busy...)
The usual scenario here is that there was a lazy port of BSP code to mainline U-Boot and you're running that instead of the BSP version (*ahemlinarocough*), someone coded bootloader support but assumed Linux will just set it up (*ahemfreescalecough*) or someone hacked up support for a board which has no public schematics (GK802/Richtechie MT-500A comes to mind) and no open-sourced board support (which is illegal by any means in the aforementioned case) - basically fixable (Linaro usually recommends using a Linaro U-Boot for example), fixable (someone may need to align board support mainline U-Boot and mainline Linux at some point), and no reason to ever bother with criminals - respectively.
What we're discussing here is basically "it used to work and now Fabio broke Linux" - actually, Fabio is removing an egregious hack that should never have been there in the first place, Linux works fine ("as always"), and the bootloader is broken.. it would never have passed QA for consumer electronics. Since these are developer boards, we can be forgiving up to a point...
--
Matt Sealey <[email protected]>
Product Development Analyst, Genesi USA, Inc.