Skip to contentSkip to conversation

ARM: dts: OMAP2+: Simplify NAND support

PATCH New Jon Hunter 2 participants 2 messages Apr 30, 2013 – May 16, 2013

Subsystems (6)
lore
Share & tools
lore

Jon Hunter

author
#0 lore raw

PATCH 1/1 ARM: dts: OMAP2+: Simplify NAND support

Commit 8c8a777 (ARM: OMAP2+: Add function to read GPMC settings from device-tree) added a device-tree property "gpmc,device-nand" to indicate is the GPMC child device is NAND. This commit should have updated the GPMC NAND documentation (Documentation/devicetree/bindings/mtd/gpmc-nand.txt) to list the property "gpmc,device-nand" as a required property and also updated the example. However, this property is redundant and not needed because the GPMC child device node for NAND is called "nand". Therefore, remove this property.

---
 Documentation/devicetree/bindings/bus/ti-gpmc.txt |    1 -
 arch/arm/boot/dts/omap3430-sdp.dts                |    1 -
 arch/arm/mach-omap2/gpmc-nand.c                   |    4 ++--
 arch/arm/mach-omap2/gpmc.c                        |    1 -
 4 files changed, 2 insertions(+), 5 deletions(-)
Documentation/devicetree/bindings/bus/ti-gpmc.txt +0 -1
index 4b87ea1..704be93 100644
@@ -95,7 +95,6 @@ GPMC chip-select settings properties for child nodes. All are optional.
 - gpmc,burst-wrap	Enables wrap bursting
 - gpmc,burst-read	Enables read page/burst mode
 - gpmc,burst-write	Enables write page/burst mode
-- gpmc,device-nand	Device is NAND
 - gpmc,device-width	Total width of device(s) connected to a GPMC
 			chip-select in bytes. The GPMC supports 8-bit
 			and 16-bit devices and so this property must be
arch/arm/boot/dts/omap3430-sdp.dts +0 -1
index 144ae43..6076d01 100644
@@ -105,7 +105,6 @@
 		nand-bus-width = <8>;
 
 		ti,nand-ecc-opt = "sw";
-		gpmc,device-nand;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <36>;
 		gpmc,cs-wr-off-ns = <36>;
arch/arm/mach-omap2/gpmc-nand.c +2 -2
index c8044b0..662c7fd 100644
@@ -102,8 +102,6 @@ int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
 		if (gpmc_nand_data->of_node) {
 			gpmc_read_settings_dt(gpmc_nand_data->of_node, &s);
 		} else {
-			s.device_nand = true;
-
 			/* Enable RD PIN Monitoring Reg */
 			if (gpmc_nand_data->dev_ready) {
 				s.wait_on_read = true;
@@ -111,6 +109,8 @@ int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
 			}
 		}
 
+		s.device_nand = true;
+
 		if (gpmc_nand_data->devsize == NAND_BUSWIDTH_16)
 			s.device_width = GPMC_DEVWIDTH_16BIT;
 		else
arch/arm/mach-omap2/gpmc.c +0 -1
index 6c4da12..6f1beb4 100644
@@ -1245,7 +1245,6 @@ void gpmc_read_settings_dt(struct device_node *np, struct gpmc_settings *p)
 
 	p->sync_read = of_property_read_bool(np, "gpmc,sync-read");
 	p->sync_write = of_property_read_bool(np, "gpmc,sync-write");
-	p->device_nand = of_property_read_bool(np, "gpmc,device-nand");
 	of_property_read_u32(np, "gpmc,device-width", &p->device_width);
 	of_property_read_u32(np, "gpmc,mux-add-data", &p->mux_add_data);
 
Signature · 1 line
1.7.10.4
maintainer
#1 lore raw

PATCH 1/1 ARM: dts: OMAP2+: Simplify NAND support

Quoted 10 lines · Jon Hunter

Commit 8c8a777 (ARM: OMAP2+: Add function to read GPMC settings from device-tree) added a device-tree property "gpmc,device-nand" to indicate is the GPMC child device is NAND. This commit should have updated the GPMC NAND documentation (Documentation/devicetree/bindings/mtd/gpmc-nand.txt) to list the property "gpmc,device-nand" as a required property and also updated the example. However, this property is redundant and not needed because the GPMC child device node for NAND is called "nand". Therefore, remove this property.

Thanks applying into omap-for-v3.11/gpmc.

Regards,

Tony