arm-soc: randconfig fixes
Subsystems (7)
cover arm-soc: randconfig fixes
Hi platform maintainers,
These patches are all fallout from randconfig testing, and I've applied them directly to the arm-soc tree since I don't expect them to be controversial. They will be part of the next set of patch submissions to Linus.
Please have a look anyway.
Arnd Bergmann (9):
ARM: tegra: Tegra114 needs CPU_FREQ_TABLE
ARM: OMAP: build SMP code only for OMAP4/5
ARM: imx: build CPU suspend code only when needed
ARM: SPEAr: conditionalize l2x0 support
ARM: imx: reset_controller may be disabled
ARM: SPEAr: conditionalize SMP code
ARM: OMAP: don't select SERIAL_OMAP unconditionally
ARM: SIRF: select SMP_ON_UP only on SMP builds
ARM: ux500: always select ABX500_CORE
arch/arm/mach-imx/headsmp.S | 2 +- arch/arm/mach-imx/src.c | 3 ++- arch/arm/mach-omap2/Kconfig | 4 ++-- arch/arm/mach-omap2/Makefile | 8 ++++---- arch/arm/mach-prima2/Kconfig | 2 +- arch/arm/mach-spear/Makefile | 6 +++--- arch/arm/mach-spear/spear13xx.c | 2 ++ arch/arm/mach-tegra/Kconfig | 1 + arch/arm/mach-ux500/Kconfig | 2 ++ 9 files changed, 18 insertions(+), 12 deletions(-)
Signature · 9 lines
1.8.1.2 Cc: Barry Song <[email protected]> Cc: Hiroshi Doyu <[email protected]> Cc: Linus Walleij <[email protected]> Cc: Sascha Hauer <[email protected]> Cc: Stephen Warren <[email protected]> Cc: Tony Lindgren <[email protected]> Cc: Viresh Kumar <[email protected]>
PATCH 1/9 ARM: tegra: Tegra114 needs CPU_FREQ_TABLE
Like the other Tegra SoCs using the same cpufreq driver, we have to enable CPU_FREQ_TABLE for this one.
drivers/built-in.o: In function `tegra_cpu_exit':
drivers/cpufreq/tegra-cpufreq.c:237: undefined reference to `cpufreq_frequency_table_cpuinfo'
--- arch/arm/mach-tegra/Kconfig | 1 + 1 file changed, 1 insertion(+)
arch/arm/mach-tegra/Kconfig +1 -0
@@ -63,6 +63,7 @@ config ARCH_TEGRA_114_SOC select ARM_ARCH_TIMER select ARM_GIC select ARM_L1_CACHE_SHIFT_6 + select CPU_FREQ_TABLE if CPU_FREQ select CPU_V7 select PINCTRL select PINCTRL_TEGRA114
Signature · 1 line
1.8.1.2
PATCH 1/9 ARM: tegra: Tegra114 needs CPU_FREQ_TABLE
Quoted 19 lines · Arnd Bergmann
Like the other Tegra SoCs using the same cpufreq driver, we have to enable
CPU_FREQ_TABLEfor this one.
drivers/built-in.o: In function `tegra_cpu_exit':
drivers/cpufreq/tegra-cpufreq.c:237: undefined reference to `cpufreq_frequency_table_cpuinfo'Cc Stephen Warren <[email protected]>Cc Hiroshi Doyu <[email protected]>Signed-off-by Arnd Bergmann <[email protected]>--- arch/arm/mach-tegra/Kconfig | 1 + 1 file changed, 1 insertion(+)arch/arm/mach-tegra/Kconfig +0
-0
arch/arm/mach-tegra/Kconfig config ARCH_TEGRA_114_SOC · line 69
Quoted 7 lines
arch/arm/mach-tegra/Kconfig +1
-0@@ -63,6 +63,7 @@ config ARCH_TEGRA_114_SOC select ARM_ARCH_TIMER select ARM_GIC select ARM_L1_CACHE_SHIFT_6 + select CPU_FREQ_TABLE if CPU_FREQ select CPU_V7 select PINCTRL select PINCTRL_TEGRA114
I doubt which is the best place for doing this? This one or cpufreq/Kconfig.arm with select CPU_FREQ_TABLE for tegra?
PATCH 1/9 ARM: tegra: Tegra114 needs CPU_FREQ_TABLE
Quoted 8 lines · On Friday 03 May 2013 10:27:17 Viresh Kumar wrote:
Quoted 8 lines
arch/arm/mach-tegra/Kconfig +0
-0@@ -63,6 +63,7 @@ config ARCH_TEGRA_114_SOC select ARM_ARCH_TIMER select ARM_GIC select ARM_L1_CACHE_SHIFT_6
Quoted 8 lines
arch/arm/mach-tegra/Kconfig config ARCH_TEGRA_114_SOC · line 69
Quoted 4 lines
arch/arm/mach-tegra/Kconfig +1
-0+ select CPU_FREQ_TABLE if CPU_FREQ select CPU_V7 select PINCTRL select PINCTRL_TEGRA114I doubt which is the best place for doing this? This one or cpufreq/Kconfig.arm with select
CPU_FREQ_TABLEfor tegra?
It would be much better IMHO to have an entry for TEGRA_CPUFREQ in drivers/cpufreq/Kcofnig.arm and move the select there. However, creating that entry has some (small) regression potential and I didn't want to do that now but instead just made sure that all three Tegra SoCs do the same thing for now.
Arnd
PATCH 1/9 ARM: tegra: Tegra114 needs CPU_FREQ_TABLE
Quoted 18 lines · Arnd Bergmann
Quoted 8 lines · On Friday 03 May 2013 10:27:17 Viresh Kumar wrote:
Quoted 8 lines
arch/arm/mach-tegra/Kconfig +0
-0@@ -63,6 +63,7 @@ config ARCH_TEGRA_114_SOC select ARM_ARCH_TIMER select ARM_GIC select ARM_L1_CACHE_SHIFT_6Quoted 8 lines
arch/arm/mach-tegra/Kconfig config ARCH_TEGRA_114_SOC · line 69
Quoted 4 lines
arch/arm/mach-tegra/Kconfig +1
-0+ select CPU_FREQ_TABLE if CPU_FREQ select CPU_V7 select PINCTRL select PINCTRL_TEGRA114I doubt which is the best place for doing this? This one or cpufreq/Kconfig.arm with select
CPU_FREQ_TABLEfor tegra?
Quoted 5 lines
It would be much better IMHO to have an entry for
TEGRA_CPUFREQindrivers/cpufreq/Kcofnig.armand move the select there. However, creating that entry has some (small) regression potential and I didn't want to do that now but instead just made sure that all three Tegra SoCs do the same thing for now.
I was under the impression that this entry is already there.
PATCH 2/9 ARM: OMAP: build SMP code only for OMAP4/5
In reply to Arnd BergmannThe OMAP platform code assumes that SMP is only ever enabled when CONFIG_ARCH_OMAP4 or CONFIG_SOC_OMAP5 is enabled, which is not necessarirly true in a multiplatform configuration.
arch/arm/mach-omap2/built-in.o: In function `omap4_smp_prepare_cpus':
:(.init.text+0x413c): undefined reference to omap_get_wakeupgen_base' :(.init.text+0x415c): undefined reference to omap_secure_apis_support'arch/arm/mach-omap2/built-in.o: In function `omap4_boot_secondary':
:(.cpuinit.text+0x28): undefined reference to omap_get_wakeupgen_base' :(.cpuinit.text+0x3c): undefined reference to omap_secure_apis_support'arch/arm/mach-omap2/built-in.o: In function `omap4_cpu_die':
:(.ref.text+0x8): undefined reference to omap_get_wakeupgen_base' :(.ref.text+0x10): undefined reference to omap_secure_apis_support' :(.ref.text+0x4c): undefined reference to omap4_hotplug_cpu' :(.ref.text+0x50): undefined reference to omap_secure_apis_support'
--- arch/arm/mach-omap2/Makefile | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
arch/arm/mach-omap2/Makefile +4 -4
@@ -32,12 +32,12 @@ obj-$(CONFIG_SOC_HAS_OMAP2_SDRC) += sdrc.o # SMP support ONLY available for OMAP4 -obj-$(CONFIG_SMP) += omap-smp.o omap-headsmp.o -obj-$(CONFIG_HOTPLUG_CPU) += omap-hotplug.o +smp-$(CONFIG_SMP) += omap-smp.o omap-headsmp.o +smp-$(CONFIG_HOTPLUG_CPU) += omap-hotplug.o omap-4-5-common = omap4-common.o omap-wakeupgen.o \ sleep44xx.o -obj-$(CONFIG_ARCH_OMAP4) += $(omap-4-5-common) -obj-$(CONFIG_SOC_OMAP5) += $(omap-4-5-common) +obj-$(CONFIG_ARCH_OMAP4) += $(omap-4-5-common) $(smp-y) +obj-$(CONFIG_SOC_OMAP5) += $(omap-4-5-common) $(smp-y) plus_sec := $(call as-instr,.arch_extension sec,+sec) AFLAGS_omap-headsmp.o :=-Wa,-march=armv7-a$(plus_sec)
Signature · 1 line
1.8.1.2
Tony Lindgren
maintainerPATCH 2/9 ARM: OMAP: build SMP code only for OMAP4/5
Quoted 4 lines · Arnd Bergmann
The OMAP platform code assumes that SMP is only ever enabled when
CONFIG_ARCH_OMAP4orCONFIG_SOC_OMAP5is enabled, which is not necessarirly true in a multiplatform configuration.
Quoted 12 lines
arch/arm/mach-omap2/built-in.o: In function `omap4_smp_prepare_cpus':
:(.init.text+0x413c): undefined reference toomap_get_wakeupgen_base' :(.init.text+0x415c): undefined reference toomap_secure_apis_support'arch/arm/mach-omap2/built-in.o: In function `omap4_boot_secondary':
:(.cpuinit.text+0x28): undefined reference toomap_get_wakeupgen_base' :(.cpuinit.text+0x3c): undefined reference toomap_secure_apis_support'arch/arm/mach-omap2/built-in.o: In function `omap4_cpu_die':
:(.ref.text+0x8): undefined reference toomap_get_wakeupgen_base' :(.ref.text+0x10): undefined reference toomap_secure_apis_support' :(.ref.text+0x4c): undefined reference toomap4_hotplug_cpu' :(.ref.text+0x50): undefined reference toomap_secure_apis_support'
Quoted 29 lines
Signed-off-by Arnd Bergmann <[email protected]>--- arch/arm/mach-omap2/Makefile | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)arch/arm/mach-omap2/Makefile +4
-4@@ -32,12 +32,12 @@ obj-$(CONFIG_SOC_HAS_OMAP2_SDRC) += sdrc.o # SMP support ONLY available for OMAP4 -obj-$(CONFIG_SMP) += omap-smp.o omap-headsmp.o -obj-$(CONFIG_HOTPLUG_CPU) += omap-hotplug.o +smp-$(CONFIG_SMP) += omap-smp.o omap-headsmp.o +smp-$(CONFIG_HOTPLUG_CPU) += omap-hotplug.o omap-4-5-common = omap4-common.o omap-wakeupgen.o \ sleep44xx.o -obj-$(CONFIG_ARCH_OMAP4) += $(omap-4-5-common) -obj-$(CONFIG_SOC_OMAP5) += $(omap-4-5-common) +obj-$(CONFIG_ARCH_OMAP4) += $(omap-4-5-common) $(smp-y) +obj-$(CONFIG_SOC_OMAP5) += $(omap-4-5-common) $(smp-y) plus_sec := $(call as-instr,.arch_extension sec,+sec) AFLAGS_omap-headsmp.o :=-Wa,-march=armv7-a$(plus_sec)Signature · 1 line
1.8.1.2
PATCH 3/9 ARM: imx: build CPU suspend code only when needed
In reply to Arnd BergmannThe ARM CPU suspend function has its own configuration symbol, which we need to use for conditionalizing any code calling into it as well.
arch/arm/mach-imx/built-in.o: In function `v7_cpu_resume':
/git/arm-soc/arch/arm/mach-imx/headsmp.S:57: undefined
reference to `cpu_resume'
--- arch/arm/mach-imx/headsmp.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-imx/headsmp.S +1 -1
@@ -24,7 +24,7 @@ ENTRY(v7_secondary_startup) ENDPROC(v7_secondary_startup) #endif -#ifdef CONFIG_PM +#ifdef CONFIG_ARM_CPU_SUSPEND /* * The following code must assume it is running from physical address * where absolute virtual addresses to the data section have to be
Signature · 1 line
1.8.1.2
PATCH 4/9 ARM: SPEAr: conditionalize l2x0 support
In reply to Arnd BergmannIf the cache controller implementation is disabled at build time, we must not call any functions related to it.
arch/arm/mach-spear/built-in.o: In function `spear13xx_l2x0_init':arch/arm/mach-spear/spear13xx.c:47: undefined reference to `l2x0_init'
--- arch/arm/mach-spear/spear13xx.c | 2 ++ 1 file changed, 2 insertions(+)
arch/arm/mach-spear/spear13xx.c +2 -0
@@ -35,6 +35,8 @@ void __init spear13xx_l2x0_init(void)* write alloc and 'Full line of zero' options * */ +if (!IS_ENABLED (CONFIG_CACHE_L2X0 )) +return ;writel_relaxed (0x06 ,VA_L2CC_BASE +L2X0_PREFETCH_CTRL );
Signature · 1 line
1.8.1.2
PATCH 5/9 ARM: imx: reset_controller may be disabled
In reply to Arnd BergmannThe new reset controller API is optional, so if that is disabled, we must not call it from platform code.
arch/arm/mach-imx/built-in.o: In function
`imx_src_init': /git/arm-soc/arch/arm/mach-imx/src.c:144:
undefined reference to `reset_controller_register'
--- arch/arm/mach-imx/src.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
arch/arm/mach-imx/src.c +2 -1
@@ -141,7 +141,8 @@ void __init imx_src_init(void)WARN_ON (!src_base); imx_reset_controller.of_node = np; -reset_controller_register (&imx_reset_controller); +if (IS_ENABLED (CONFIG_RESET_CONTROLLER )) +reset_controller_register (&imx_reset_controller);/* * force warm reset sources to generate cold reset
Signature · 1 line
1.8.1.2
PATCH 6/9 ARM: SPEAr: conditionalize SMP code
In reply to Arnd BergmannSome constant definitions are only defined for spear13xx, so we must not attempt to build SPEAr SMP support when that SoC is not enabled.
arch/arm/mach-spear/platsmp.c:25:35:
error: 'VA_SCU_BASE' undeclared here (not in a function) arch/arm/mach-spear/platsmp.c: In function 'spear13xx_smp_prepare_cpus':
arch/arm/mach-spear/platsmp.c:111:58: error: 'SYS_LOCATION' undeclared (first use in this function)
--- arch/arm/mach-spear/Makefile | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
arch/arm/mach-spear/Makefile +3 -3
@@ -7,10 +7,10 @@ ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include # Common support obj-y := restart.o time.o -obj-$(CONFIG_SMP) += headsmp.o platsmp.o -obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o +smp-$(CONFIG_SMP) += headsmp.o platsmp.o +smp-$(CONFIG_HOTPLUG_CPU) += hotplug.o -obj-$(CONFIG_ARCH_SPEAR13XX) += spear13xx.o +obj-$(CONFIG_ARCH_SPEAR13XX) += spear13xx.o $(smp-y) obj-$(CONFIG_MACH_SPEAR1310) += spear1310.o obj-$(CONFIG_MACH_SPEAR1340) += spear1340.o
Signature · 1 line
1.8.1.2
PATCH 7/9 ARM: OMAP: don't select SERIAL_OMAP unconditionally
In reply to Arnd BergmannIt is possible to build a kernel without TTY support, so we must not attempt to select SERIAL_OMAP in that case.
warning: (ARCH_OMAP2PLUS_TYPICAL) selects SERIAL_OMAP which has unmet direct dependencies (TTY && HAS_IOMEM && GENERIC_HARDIRQS && ARCH_OMAP2PLUS)
--- arch/arm/mach-omap2/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/mach-omap2/Kconfig +2 -2
@@ -37,8 +37,8 @@ config ARCH_OMAP2PLUS_TYPICAL select NEON if ARCH_OMAP3 || ARCH_OMAP4 || SOC_OMAP5 select PM_RUNTIME select REGULATOR - select SERIAL_OMAP - select SERIAL_OMAP_CONSOLE + select SERIAL_OMAP if TTY + select SERIAL_OMAP_CONSOLE if TTY select TWL4030_CORE if ARCH_OMAP3 || ARCH_OMAP4 select TWL4030_POWER if ARCH_OMAP3 || ARCH_OMAP4 select VFP
Signature · 1 line
1.8.1.2
Tony Lindgren
maintainerPATCH 7/9 ARM: OMAP: don't select SERIAL_OMAP unconditionally
Quoted 16 lines · Arnd Bergmann
It is possible to build a kernel without TTY support, so we must not attempt to select
SERIAL_OMAPin that case.warning: (
ARCH_OMAP2PLUS_TYPICAL) selectsSERIAL_OMAPwhich has unmet direct dependencies (TTY &&HAS_IOMEM&&GENERIC_HARDIRQS&&ARCH_OMAP2PLUS)Cc Tony Lindgren <[email protected]>Signed-off-by Arnd Bergmann <[email protected]>--- arch/arm/mach-omap2/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)arch/arm/mach-omap2/Kconfig +0
-0
arch/arm/mach-omap2/Kconfig config ARCH_OMAP2PLUS_TYPICAL · line 44
Quoted 10 lines
arch/arm/mach-omap2/Kconfig +2
-2@@ -37,8 +37,8 @@ config ARCH_OMAP2PLUS_TYPICAL select NEON if ARCH_OMAP3 || ARCH_OMAP4 || SOC_OMAP5 select PM_RUNTIME select REGULATOR - select SERIAL_OMAP - select SERIAL_OMAP_CONSOLE + select SERIAL_OMAP if TTY + select SERIAL_OMAP_CONSOLE if TTY select TWL4030_CORE if ARCH_OMAP3 || ARCH_OMAP4 select TWL4030_POWER if ARCH_OMAP3 || ARCH_OMAP4 select VFP
Please just drop this and pick my earlier fix instead:
[PATCH 1/3] ARM: OMAP2+: Fix unmet direct dependencies for SERIAL_OMAP
Or let me know if you prefer me to queue it.
Regards,
Tony
PATCH 7/9 ARM: OMAP: don't select SERIAL_OMAP unconditionally
Quoted 5 lines · Tony Lindgren
Please just drop this and pick my earlier fix instead:
[PATCH 1/3] ARM: OMAP2+: Fix unmet direct dependencies for
SERIAL_OMAPOr let me know if you prefer me to queue it.
I've applied your patch now. Should I also take the other two of that series? I was not on Cc for these patches, but all three seem to be required still.
Arnd
Tony Lindgren
maintainerPATCH 7/9 ARM: OMAP: don't select SERIAL_OMAP unconditionally
Quoted 10 lines · Arnd Bergmann
Quoted 5 lines · Tony Lindgren
Please just drop this and pick my earlier fix instead:
[PATCH 1/3] ARM: OMAP2+: Fix unmet direct dependencies for
SERIAL_OMAPOr let me know if you prefer me to queue it.
I've applied your patch now. Should I also take the other two of that series? I was not on Cc for these patches, but all three seem to be required still.
Yes go for it. Note that the two other patches have dependencies to branches for the current merge window, but you probably already have some base they can be applied against.
Regards,
Tony
PATCH 8/9 ARM: SIRF: select SMP_ON_UP only on SMP builds
In reply to Arnd BergmannLike all other platforms, we can only select SMP_ON_UP if SMP is also enabled.
warning: (SOC_IMX31 && SOC_IMX35 && ARCH_MARCO) selects
SMP_ON_UP which has unmet direct dependencies (SMP && !XIP_KERNEL)
--- arch/arm/mach-prima2/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-prima2/Kconfig +1 -1
@@ -38,7 +38,7 @@ config ARCH_MARCO select CPU_V7 select HAVE_ARM_SCU if SMP select HAVE_SMP - select SMP_ON_UP + select SMP_ON_UP if SMP help Support for CSR SiRFSoC ARM Cortex A9 Platform
Signature · 1 line
1.8.1.2
PATCH 9/9 ARM: ux500: always select ABX500_CORE
In reply to Arnd BergmannThe use of 'select' in the ux500 platform is a huge mess, we should not be selecting most of the drivers that are currently selected there, but rather enable them from the defconfig.
As a fixup for 3.10, let's at least select the dependencies for the other drivers we already select, to make it consistent.
warning: (UX500_SOC_COMMON) selects AB8500_CORE which has unmet direct dependencies (HAS_IOMEM && GENERIC_HARDIRQS && ABX500_CORE && MFD_DB8500_PRCMU)
--- arch/arm/mach-ux500/Kconfig | 2 ++ 1 file changed, 2 insertions(+)
arch/arm/mach-ux500/Kconfig +2 -0
@@ -19,6 +19,8 @@ if ARCH_U8500 config UX500_SOC_COMMON bool default y + select ABX500_CORE + select AB8500_CORE select ARM_ERRATA_754322 select ARM_ERRATA_764369 if SMP select ARM_GIC
Signature · 1 line
1.8.1.2
PATCH 9/9 ARM: ux500: always select ABX500_CORE
Quoted 11 lines · Arnd Bergmann
The use of 'select' in the ux500 platform is a huge mess, we should not be selecting most of the drivers that are currently selected there, but rather enable them from the defconfig.
As a fixup for 3.10, let's at least select the dependencies for the other drivers we already select, to make it consistent.
warning: (
UX500_SOC_COMMON) selectsAB8500_COREwhich has unmet direct dependencies (HAS_IOMEM&&GENERIC_HARDIRQS&&ABX500_CORE&&MFD_DB8500_PRCMU)Cc Linus Walleij <[email protected]>Signed-off-by Arnd Bergmann <[email protected]>
I do not necessarily agree with this commit message.
The only mess I see is that this very patch is missing...
If we look at this:
config UX500_SOC_DB8500
bool
select CPU_FREQ_TABLE if CPU_FREQ
select MFD_DB8500_PRCMU
select PINCTRL_DB8500
select PINCTRL_DB8540
select PINCTRL_AB8500
select PINCTRL_AB8505
select PINCTRL_AB9540
select PINCTRL_AB8540
select REGULATOR
select REGULATOR_DB8500_PRCMU
The PRCMU, the PINCTRL drivers, and the PRCMU regulators are necessary to boot the system correctly, by which I mean necessary so as not to cause potential damage to the hardware.
The PRCMU is a system controller without which the system cannot really be brought up, and the ABx500's are the PMICs which are developed in pair with the SoC and they are in practice Siamese twins, there is no chance you can build a Ux500 system without both of them. It just won't even start. There are deep dependencies between the PRCMU and the ABx500, as the PRCMU firmware will talk directly to the ABx500 without the kernel intervening. I.e. the whole set of hardware has to be there.
While I understand that from a compile-time point of view it does not seem nice, and all things would be separate units that you plug in, from a run-time and system architecture point of view it makes a lot of sense to select these. Worlds collide...
Apart from that:
Yours,
Linus Walleij
PATCH 9/9 ARM: ux500: always select ABX500_CORE
Quoted 34 lines · On Friday 03 May 2013 10:14:28 Linus Walleij wrote:
I do not necessarily agree with this commit message.
The only mess I see is that this very patch is missing...
If we look at this:
config
UX500_SOC_DB8500
bool
selectCPU_FREQ_TABLEifCPU_FREQ
selectMFD_DB8500_PRCMU
selectPINCTRL_DB8500
selectPINCTRL_DB8540
selectPINCTRL_AB8500
selectPINCTRL_AB8505
selectPINCTRL_AB9540
selectPINCTRL_AB8540
select REGULATOR
selectREGULATOR_DB8500_PRCMUThe PRCMU, the PINCTRL drivers, and the PRCMU regulators are necessary to boot the system correctly, by which I mean necessary so as not to cause potential damage to the hardware.
The PRCMU is a system controller without which the system cannot really be brought up, and the ABx500's are the PMICs which are developed in pair with the SoC and they are in practice Siamese twins, there is no chance you can build a Ux500 system without both of them. It just won't even start. There are deep dependencies between the PRCMU and the ABx500, as the PRCMU firmware will talk directly to the ABx500 without the kernel intervening. I.e. the whole set of hardware has to be there.
Quoted 7 lines
While I understand that from a compile-time point of view it does not seem nice, and all things would be separate units that you plug in, from a run-time and system architecture point of view it makes a lot of sense to select these. Worlds collide...
Apart from that:
Acked-by Linus Walleij <[email protected]>
If they are completely essential, we should not have an entry like
config AB8500_CORE
bool "ST-Ericsson AB8500 Mixed Signal Power Management chip" depends on GENERIC_HARDIRQS && ABX500_CORE && MFD_DB8500_PRCMU select POWER_SUPPLY
select MFD_CORE
select IRQ_DOMAIN
help
Select this option to enable access to AB8500 power management chip. This connects to U8500 either on the SSP/SPI bus (deprecated since hardware version v1.0) or the I2C bus via PRCMU. It also adds the irq_chip parts for handling the Mixed Signal chip events. This chip embeds various other multimedia funtionalities as well.
(and more of the same) in drivers/mfd/Kconfig. The rule is that you either make a Kconfig option user-selectable or make it always selected by another option.
My preference would be to make it user-selectable and enable it only in the defconfig, but if that can damage the hardware, we should not actually provide a named option.
Arnd
PATCH 9/9 ARM: ux500: always select ABX500_CORE
Quoted 6 lines · Arnd Bergmann
Quoted 4 lines · On Friday 03 May 2013 10:14:28 Linus Walleij wrote:
While I understand that from a compile-time point of view it does not seem nice, and all things would be separate units that you plug in, from a run-time and system architecture point of view it makes a lot of sense to select these. Worlds collide...
(...)
Quoted 3 lines
My preference would be to make it user-selectable and enable it only in the defconfig, but if that can damage the hardware, we should not actually provide a named option.
Hm I'd lean towards the latter. However the AB8500 has subdrivers and *some* of these are optional, such as the RTC. And it'd be strange to have that depend on some totally unrelated config symbol like UX500_SOC_COMMON.
I think that in that case we should make AB8500_CORE a hidden (non-user selectable) bool so it is more logical.
However any if these approaches will lead to unaestetic menuconfig with AB8500 suboptions appearing right in the MFD menu instead of being ordered under a AB8500_CORE node which is better for anyone actually trying to use menuconfig interactively.
The latter aestetic is one of the reasons why it looks as it does IIRC, but maybe that is HTML thinking :-)
Yours,
Linus Walleij
PATCH 9/9 ARM: ux500: always select ABX500_CORE
Quoted 12 lines · On Friday 03 May 2013 14:13:20 Linus Walleij wrote:
Quoted 6 lines · Arnd Bergmann
Quoted 4 lines · On Friday 03 May 2013 10:14:28 Linus Walleij wrote:
While I understand that from a compile-time point of view it does not seem nice, and all things would be separate units that you plug in, from a run-time and system architecture point of view it makes a lot of sense to select these. Worlds collide...
(...)
Quoted 3 lines
My preference would be to make it user-selectable and enable it only in the defconfig, but if that can damage the hardware, we should not actually provide a named option.
Quoted 7 lines
Hm I'd lean towards the latter. However the AB8500 has subdrivers and *some* of these are optional, such as the RTC. And it'd be strange to have that depend on some totally unrelated config symbol like
UX500_SOC_COMMON.I think that in that case we should make
AB8500_COREa hidden (non-user selectable) bool so it is more logical.
Yes, makes sense.
Quoted 4 lines
However any if these approaches will lead to unaestetic menuconfig with AB8500 suboptions appearing right in the MFD menu instead of being ordered under a
AB8500_COREnode which is better for anyone actually trying to use menuconfig interactively.
Yes, I can see that. Right now we have:
-*- ST-Ericsson ABX500 Mixed Signal Circuit register functions
[*] ST-Ericsson AB3100 Mixed Signal Circuit core functions
[*] ST-Ericsson AB3100 OTP functions
-*- ST-Ericsson AB8500 Mixed Signal Power Management chip
[*] ST-Ericsson AB8500 GPADC driver
[*] Enable debug info via debugfs
-*- ST-Ericsson DB8500 Power Reset Control Management Unit
I think we can certainly eliminate the ABX500 option, this one can just get selected by AB3100 and AB8500. The PRCMU can also be silent because as you say it is always needed.
One possible reason to allow them to be selected is to enable build-time coverage on other platforms, but at the moment, they all depend on ARCH_U300|ARCH_U8500, presumably because until very recently they would not actually build anywhere else.
The GPADC driver is interesting: it does not have its own user interface (besides the debugging driver) and could just get selected by the other drivers using its exported interfaces. It would also be better to convert it to the standard IIO ADC interface, but I don't know if that's realistic. This leavs the debugging interface as the only sub-option. Do you know if that is actually being used by developers, or is this one of those interfaces that were created during bringup and then never touched again after everything worked?
Regarding AB3100, I assume the relationship to U300 is similar to that between DB8500 and AB8500. Are you able to boot a U300 system without touching AB3100?
Arnd
PATCH 9/9 ARM: ux500: always select ABX500_CORE
Quoted 3 lines · Arnd Bergmann
I think we can certainly eliminate the ABX500 option, this one can just get selected by AB3100 and AB8500. The PRCMU can also be silent because as you say it is always needed.
OK sounds like a plan.
Quoted 5 lines
The GPADC driver is interesting: it does not have its own user interface (besides the debugging driver) and could just get selected by the other drivers using its exported interfaces. It would also be better to convert it to the standard IIO ADC interface, but I don't know if that's realistic.
This should be moved over to IIO ADC, that subsystem however did not exist when this driver was submitted, that is why it ended up in MFD. As usual someone needs to go hack on it...
Quoted 5 lines
This leavs the debugging
interface as the only sub-option. Do you know if that is actually being used by developers, or is this one of those interfaces that were created during bringup and then never touched again after everything worked?
Something like that, but as long as new platforms using that ASIC is coming out it remains quite usable for this.
It is also used for hardware validation, where you hook up the system with a lot of electric probes and want to set specific bits here and there to validate functionality. There just a minor change to the silicon or packaging triggers such re-validation.
The usecase is similar to the debug interface we invented for pin control recently, however there we managed to make things centralized.
Quoted 3 lines
Regarding AB3100, I assume the relationship to U300 is similar to that between DB8500 and AB8500. Are you able to boot a U300 system without touching AB3100?
I would say no. The system will be in some bootstrap state unless you bring up the AB3100, and especially the regulators.
These are default y but should arguably be selected y instead.
The U300 SoC will bootstrap power in a strange way until the regulators are up, and then hand over to software-controlled regulators for powering the SoC and release that bootstrap.
This is not harmful but a very strange and it's doubtful whether I would call that "fully booted". It's something like booting into "safe mode"
http://en.wikipedia.org/wiki/Safe_mode
Not enabling regulators on the U300 will have other strange effects ... like MMC/SD not working. Yet we can not have depends on REGULATORS in the Kconfig for the MMCI driver since this driver is also used on systems without the regulator framework (hardwired power).
All these run-time "makes sense" is in a bit of flux as compared to config-and-compile-time "makes sense" unfortunately.
I lean toward selecting AB3100 and REGULATOR_AB3100 for the U300 actually.
Yours,
Linus Walleij
PATCH 9/9 ARM: ux500: always select ABX500_CORE
Quoted 11 lines · On Friday 03 May 2013 15:33:17 Linus Walleij wrote:
Quoted 5 lines · Arnd Bergmann
This leavs the debugging
interface as the only sub-option. Do you know if that is actually being used by developers, or is this one of those interfaces that were created during bringup and then never touched again after everything worked?Something like that, but as long as new platforms using that ASIC is coming out it remains quite usable for this.
Quoted 8 lines
It is also used for hardware validation, where you hook up the system with a lot of electric probes and want to set specific bits here and there to validate functionality. There just a minor change to the silicon or packaging triggers such re-validation.
The usecase is similar to the debug interface we invented for pin control recently, however there we managed to make things centralized.
Ok, makes sense.
Quoted 10 lines
Quoted 3 lines
Regarding AB3100, I assume the relationship to U300 is similar to that between DB8500 and AB8500. Are you able to boot a U300 system without touching AB3100?
I would say no. The system will be in some bootstrap state unless you bring up the AB3100, and especially the regulators.
These are default y but should arguably be selected y instead.
Quoted 8 lines
The U300 SoC will bootstrap power in a strange way until the regulators are up, and then hand over to software-controlled regulators for powering the SoC and release that bootstrap.
This is not harmful but a very strange and it's doubtful whether I would call that "fully booted". It's something like booting into "safe mode"
http://en.wikipedia.org/wiki/Safe_mode
I see.
Quoted 11 lines
Not enabling regulators on the U300 will have other strange effects ... like MMC/SD not working. Yet we can not have depends on REGULATORS in the
Kconfigfor the MMCI driver since this driver is also used on systems without the regulator framework (hardwired power).All these run-time "makes sense" is in a bit of flux as compared to config-and-compile-time "makes sense" unfortunately.
I lean toward selecting AB3100 and
REGULATOR_AB3100for the U300 actually.
Should we still allow building them on other platforms then? Right now, these depend on the platforms that actually use the hardware, but in other places, we just allow everything to be built that compiles without errors.
Is it theoretically possible to use the AB in combination with another (non-ST-Ericsson) digital baseband?
Arnd
PATCH 9/9 ARM: ux500: always select ABX500_CORE
Quoted 9 lines · Arnd Bergmann
Quoted 2 lines · On Friday 03 May 2013 15:33:17 Linus Walleij wrote:
I lean toward selecting AB3100 and
REGULATOR_AB3100for the U300 actually.Should we still allow building them on other platforms then? Right now, these depend on the platforms that actually use the hardware, but in other places, we just allow everything to be built that compiles without errors.
Not in my opinion but IIRC in 2008 or so some other subsystem maintainer beat us up for not allowing it to build on every other platform, and the rationale given was that allowin this to build on e.g. x86_64 gives some nice compile coverage.
I don't know which argument wins :-)
Quoted 2 lines
Is it theoretically possible to use the AB in combination with another (non-ST-Ericsson) digital baseband?
Theoretically (it's just a bunch of regulators etc when all comes around), but it won't happen since these components
are not sold separately.
Yours,
Linus Walleij
PATCH 9/9 ARM: ux500: always select ABX500_CORE
Quoted 11 lines · On Friday 03 May 2013 16:06:57 Linus Walleij wrote:
Quoted 9 lines · Arnd Bergmann
Quoted 2 lines · On Friday 03 May 2013 15:33:17 Linus Walleij wrote:
I lean toward selecting AB3100 and
REGULATOR_AB3100for the U300 actually.Should we still allow building them on other platforms then? Right now, these depend on the platforms that actually use the hardware, but in other places, we just allow everything to be built that compiles without errors.
Quoted 7 lines
Not in my opinion but IIRC in 2008 or so some other subsystem maintainer beat us up for not allowing it to build on every other platform, and the rationale given was that allowin this to build on e.g.
x86_64gives some nice compile coverage.I don't know which argument wins
I know that a certain other Linus frequently complains when ARM specific options show up on his x86 machine during "make oldconfig" ;-)
One idea I had is to create a global CONFIG_SOC option that would hide all on-chip peripherals when building for a PC-like system. On ARM, we would always select CONFIG_SOC, except for a few special cases like ARCH_RPC, ARCH_FOOTBRIDGE and ARCH_SHARK.
Quoted 6 lines
Quoted 2 lines
Is it theoretically possible to use the AB in combination with another (non-ST-Ericsson) digital baseband?
Theoretically (it's just a bunch of regulators etc when all comes around), but it won't happen since these components
are not sold separately.
Right, I was specifically asking about the technical possibilities, not what people are likely to do.
Arnd
PATCH 9/9 ARM: ux500: always select ABX500_CORE
Quoted 8 lines · Arnd Bergmann
Quoted 7 lines · On Friday 03 May 2013 16:06:57 Linus Walleij wrote:
Not in my opinion but IIRC in 2008 or so some other subsystem maintainer beat us up for not allowing it to build on every other platform, and the rationale given was that allowin this to build on e.g.
x86_64gives some nice compile coverage.
Quoted 4 lines
Quoted 1 line
I don't know which argument wins
I know that a certain other Linus frequently complains when ARM specific options show up on his x86 machine during "make oldconfig" ;-)
OK let's make it SoC-specific.
Quoted 4 lines
One idea I had is to create a global
CONFIG_SOCoption that would hide all on-chip peripherals when building for a PC-like system. On ARM, we would always selectCONFIG_SOC, except for a few special cases likeARCH_RPC,ARCH_FOOTBRIDGEandARCH_SHARK.
Sounds like a deal. The AB chips aren't on-chip though they sit on I2C or SPI actually. But they are still strongly coupled with the SoC.
I just took a stroll around the premises and found this Aardvark I2C/SPI "embedded systems interface".
This is a USB thing that makes it possible to connect any I2C or SPI peripheral to the desktop ... I don't know how such things should be used with Linux really, it seems like it's something that normally gets used from userspace by libusb but in theory we could have a kernel driver for this and plug in whatever SoC I2C/SPI device into a desktop.
Whatever use it would be ... but could be useful for developing drivers for a chip outside of the target system I believe.
Yours,
Linus Walleij
PATCH 9/9 ARM: ux500: always select ABX500_CORE
Quoted 15 lines · On Friday 03 May 2013 20:43:42 Linus Walleij wrote:
Sounds like a deal. The AB chips aren't on-chip though they sit on I2C or SPI actually. But they are still strongly coupled with the SoC.
I just took a stroll around the premises and found this Aardvark I2C/SPI "embedded systems interface".
This is a USB thing that makes it possible to connect any I2C or SPI peripheral to the desktop ... I don't know how such things should be used with Linux really, it seems like it's something that normally gets used from userspace by libusb but in theory we could have a kernel driver for this and plug in whatever SoC I2C/SPI device into a desktop.
Quoted 3 lines
Whatever use it would be ... but could be useful for developing drivers for a chip outside of the target system I believe.
I would argue that the AB8500 is close enough to a 'system-on-a-chip' to make it depend on CONFIG_SOC, even though it is technically one half of a 'system-on-two-chips'.
I would also allow x86 and all other architectures to enable CONFIG_SOC, since there are lots of SoCs these days that combine an x86 core with the same kind of peripherals we have on ARM systems. It's just not what you you find in a regualar PC or Laptop, and anyone building their own kernel can ignore those.
Arnd
cover arm-soc: randconfig fixes
In reply to Arnd BergmannQuoted 3 lines · Arnd Bergmann
Arnd Bergmann (9):
ARM: SPEAr: conditionalize l2x0 support
ARM: SPEAr: conditionalize SMP code