ARM: at91: dt: switch to pre-processor
Subsystems (3)
v2 cover ARM: at91: dt: switch to pre-processor
HI,
v2:
use common IRQ define
split patch
rebase on 3.10-rc1
The follow patch series switch the at91 to DT pre-processor
So we can use macro for AIC and Pinctrl instead of magic
The following changes since commit f722406faae2d073cc1d01063d1123c35425939e:
Linux 3.10-rc1 (2013-05-11 17:14:08 -0700)
are available in the git repository at:
git://github.com/at91linux/linux-at91.git j/for-3.11-dt
for you to fetch changes up to 3668ac6a70bc5af71a947ad7b531c57b8a787ea0:
ARM: at91: dt: switch to standard IRQ flag defines (2013-05-15 21:56:18 +0800)
----------------------------------------------------------------
Jean-Christophe PLAGNIOL-VILLARD (5):
ARM: at91: dt: use #include for all device trees
ARM: at91: dt: switch to standard GPIO flag defines.
ARM: at91: dt: add pinctrl pre-processor define
ARM: at91: dt: switch to pinctrl to pre-processor
ARM: at91: dt: switch to standard IRQ flag defines
arch/arm/boot/dts/aks-cdu.dts | 12 +-- arch/arm/boot/dts/animeo_ip.dts | 18 ++--- arch/arm/boot/dts/at91-ariag25.dts | 6 +- arch/arm/boot/dts/at91rm9200.dtsi | 207 +++++++++++++++++++++++++------------------------ arch/arm/boot/dts/at91rm9200ek.dts | 10 +-- arch/arm/boot/dts/at91sam9260.dtsi | 215 ++++++++++++++++++++++++++------------------------- arch/arm/boot/dts/at91sam9263.dtsi | 203 ++++++++++++++++++++++++------------------------ arch/arm/boot/dts/at91sam9263ek.dts | 24 +++--- arch/arm/boot/dts/at91sam9g15.dtsi | 2 +- arch/arm/boot/dts/at91sam9g15ek.dts | 4 +- arch/arm/boot/dts/at91sam9g20.dtsi | 2 +- arch/arm/boot/dts/at91sam9g20ek.dts | 6 +- arch/arm/boot/dts/at91sam9g20ek_2mmc.dts | 10 +-- arch/arm/boot/dts/at91sam9g20ek_common.dtsi | 28 ++++--- arch/arm/boot/dts/at91sam9g25.dtsi | 2 +- arch/arm/boot/dts/at91sam9g25ek.dts | 4 +- arch/arm/boot/dts/at91sam9g35.dtsi | 2 +- arch/arm/boot/dts/at91sam9g35ek.dts | 4 +- arch/arm/boot/dts/at91sam9g45.dtsi | 213 +++++++++++++++++++++++++------------------------- arch/arm/boot/dts/at91sam9m10g45ek.dts | 38 ++++----- arch/arm/boot/dts/at91sam9n12.dtsi | 141 +++++++++++++++++----------------- arch/arm/boot/dts/at91sam9n12ek.dts | 14 ++-- arch/arm/boot/dts/at91sam9x25.dtsi | 22 +++--- arch/arm/boot/dts/at91sam9x25ek.dts | 4 +- arch/arm/boot/dts/at91sam9x35.dtsi | 2 +- arch/arm/boot/dts/at91sam9x35ek.dts | 4 +- arch/arm/boot/dts/at91sam9x5.dtsi | 279 +++++++++++++++++++++++++++++++++--------------------------------- arch/arm/boot/dts/at91sam9x5cm.dtsi | 8 +- arch/arm/boot/dts/at91sam9x5ek.dtsi | 14 ++-- arch/arm/boot/dts/ethernut5.dts | 6 +- arch/arm/boot/dts/evk-pro3.dts | 6 +- arch/arm/boot/dts/ge863-pro3.dtsi | 2 +- arch/arm/boot/dts/kizbox.dts | 16 ++-- arch/arm/boot/dts/mpa1600.dts | 4 +- arch/arm/boot/dts/pm9g45.dts | 22 +++--- arch/arm/boot/dts/sama5d3.dtsi | 520 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++------------------------------------------------------------- arch/arm/boot/dts/sama5d31ek.dts | 6 +- arch/arm/boot/dts/sama5d33ek.dts | 4 +- arch/arm/boot/dts/sama5d34ek.dts | 6 +- arch/arm/boot/dts/sama5d35ek.dts | 4 +- arch/arm/boot/dts/sama5d3xcm.dtsi | 4 +- arch/arm/boot/dts/sama5d3xdm.dtsi | 2 +- arch/arm/boot/dts/sama5d3xmb.dtsi | 26 +++---- arch/arm/boot/dts/tny_a9260.dts | 4 +- arch/arm/boot/dts/tny_a9263.dts | 4 +- arch/arm/boot/dts/tny_a9g20.dts | 4 +- arch/arm/boot/dts/usb_a9260.dts | 4 +- arch/arm/boot/dts/usb_a9260_common.dtsi | 6 +- arch/arm/boot/dts/usb_a9263.dts | 8 +- arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi | 22 +++--- arch/arm/boot/dts/usb_a9g20.dts | 4 +- include/dt-bindings/pinctrl/at91.h | 35 +++++++++ 52 files changed, 1139 insertions(+), 1078 deletions(-) create mode 100644 include/dt-bindings/pinctrl/at91.h
Best Regards,
J.
PATCH 1/5 ARM: at91: dt: use #include for all device trees
to prepare the switch to the macro.
--- arch/arm/boot/dts/aks-cdu.dts | 2 +- arch/arm/boot/dts/animeo_ip.dts | 2 +- arch/arm/boot/dts/at91-ariag25.dts | 2 +- arch/arm/boot/dts/at91rm9200.dtsi | 2 +- arch/arm/boot/dts/at91rm9200ek.dts | 2 +- arch/arm/boot/dts/at91sam9260.dtsi | 2 +- arch/arm/boot/dts/at91sam9263.dtsi | 2 +- arch/arm/boot/dts/at91sam9263ek.dts | 2 +- arch/arm/boot/dts/at91sam9g15.dtsi | 2 +- arch/arm/boot/dts/at91sam9g15ek.dts | 4 ++-- arch/arm/boot/dts/at91sam9g20.dtsi | 2 +- arch/arm/boot/dts/at91sam9g20ek.dts | 2 +- arch/arm/boot/dts/at91sam9g20ek_2mmc.dts | 2 +- arch/arm/boot/dts/at91sam9g20ek_common.dtsi | 2 +- arch/arm/boot/dts/at91sam9g25.dtsi | 2 +- arch/arm/boot/dts/at91sam9g25ek.dts | 4 ++-- arch/arm/boot/dts/at91sam9g35.dtsi | 2 +- arch/arm/boot/dts/at91sam9g35ek.dts | 4 ++-- arch/arm/boot/dts/at91sam9g45.dtsi | 2 +- arch/arm/boot/dts/at91sam9m10g45ek.dts | 2 +- arch/arm/boot/dts/at91sam9n12.dtsi | 2 +- arch/arm/boot/dts/at91sam9n12ek.dts | 2 +- arch/arm/boot/dts/at91sam9x25.dtsi | 2 +- arch/arm/boot/dts/at91sam9x25ek.dts | 4 ++-- arch/arm/boot/dts/at91sam9x35.dtsi | 2 +- arch/arm/boot/dts/at91sam9x35ek.dts | 4 ++-- arch/arm/boot/dts/at91sam9x5.dtsi | 2 +- arch/arm/boot/dts/at91sam9x5ek.dtsi | 2 +- arch/arm/boot/dts/ethernut5.dts | 2 +- arch/arm/boot/dts/evk-pro3.dts | 4 ++-- arch/arm/boot/dts/ge863-pro3.dtsi | 2 +- arch/arm/boot/dts/kizbox.dts | 4 ++-- arch/arm/boot/dts/mpa1600.dts | 2 +- arch/arm/boot/dts/pm9g45.dts | 2 +- arch/arm/boot/dts/sama5d3.dtsi | 2 +- arch/arm/boot/dts/sama5d31ek.dts | 4 ++-- arch/arm/boot/dts/sama5d33ek.dts | 4 ++-- arch/arm/boot/dts/sama5d34ek.dts | 4 ++-- arch/arm/boot/dts/sama5d35ek.dts | 2 +- arch/arm/boot/dts/sama5d3xcm.dtsi | 2 +- arch/arm/boot/dts/sama5d3xmb.dtsi | 2 +- arch/arm/boot/dts/tny_a9260.dts | 4 ++-- arch/arm/boot/dts/tny_a9263.dts | 2 +- arch/arm/boot/dts/tny_a9g20.dts | 4 ++-- arch/arm/boot/dts/usb_a9260.dts | 4 ++-- arch/arm/boot/dts/usb_a9263.dts | 2 +- arch/arm/boot/dts/usb_a9g20.dts | 4 ++-- 47 files changed, 61 insertions(+), 61 deletions(-)
arch/arm/boot/dts/aks-cdu.dts +1 -1
@@ -9,7 +9,7 @@ /dts-v1/; -/include/ "ge863-pro3.dtsi" +#include "ge863-pro3.dtsi" / { chosen {
arch/arm/boot/dts/animeo_ip.dts +1 -1
@@ -7,7 +7,7 @@ */ /dts-v1/; -/include/ "at91sam9260.dtsi" +#include "at91sam9260.dtsi" / { model = "Somfy Animeo IP";
arch/arm/boot/dts/at91-ariag25.dts +1 -1
@@ -7,7 +7,7 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9g25.dtsi" +#include "at91sam9g25.dtsi" / { model = "Acme Systems Aria G25";
arch/arm/boot/dts/at91rm9200.dtsi +1 -1
@@ -10,7 +10,7 @@ * Licensed under GPLv2 or later. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { model = "Atmel AT91RM9200 family SoC";
arch/arm/boot/dts/at91rm9200ek.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2 only */ /dts-v1/; -/include/ "at91rm9200.dtsi" +#include "at91rm9200.dtsi" / { model = "Atmel AT91RM9200 evaluation kit";
arch/arm/boot/dts/at91sam9260.dtsi +1 -1
@@ -8,7 +8,7 @@ * Licensed under GPLv2 or later. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { model = "Atmel AT91SAM9260 family SoC";
arch/arm/boot/dts/at91sam9263.dtsi +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2 only. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { model = "Atmel AT91SAM9263 family SoC";
arch/arm/boot/dts/at91sam9263ek.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2 only */ /dts-v1/; -/include/ "at91sam9263.dtsi" +#include "at91sam9263.dtsi" / { model = "Atmel at91sam9263ek";
arch/arm/boot/dts/at91sam9g15.dtsi +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ -/include/ "at91sam9x5.dtsi" +#include "at91sam9x5.dtsi" / { model = "Atmel AT91SAM9G15 SoC";
arch/arm/boot/dts/at91sam9g15ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9g15.dtsi" -/include/ "at91sam9x5ek.dtsi" +#include "at91sam9g15.dtsi" +#include "at91sam9x5ek.dtsi" / { model = "Atmel AT91SAM9G15-EK";
arch/arm/boot/dts/at91sam9g20.dtsi +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ -/include/ "at91sam9260.dtsi" +#include "at91sam9260.dtsi" / { model = "Atmel AT91SAM9G20 family SoC";
arch/arm/boot/dts/at91sam9g20ek.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ /dts-v1/; -/include/ "at91sam9g20ek_common.dtsi" +#include "at91sam9g20ek_common.dtsi" / { model = "Atmel at91sam9g20ek";
arch/arm/boot/dts/at91sam9g20ek_2mmc.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ /dts-v1/; -/include/ "at91sam9g20ek_common.dtsi" +#include "at91sam9g20ek_common.dtsi" / { model = "Atmel at91sam9g20ek 2 mmc";
arch/arm/boot/dts/at91sam9g20ek_common.dtsi +1 -1
@@ -5,7 +5,7 @@ * * Licensed under GPLv2. */ -/include/ "at91sam9g20.dtsi" +#include "at91sam9g20.dtsi" / {
arch/arm/boot/dts/at91sam9g25.dtsi +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ -/include/ "at91sam9x5.dtsi" +#include "at91sam9x5.dtsi" / { model = "Atmel AT91SAM9G25 SoC";
arch/arm/boot/dts/at91sam9g25ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9g25.dtsi" -/include/ "at91sam9x5ek.dtsi" +#include "at91sam9g25.dtsi" +#include "at91sam9x5ek.dtsi" / { model = "Atmel AT91SAM9G25-EK";
arch/arm/boot/dts/at91sam9g35.dtsi +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ -/include/ "at91sam9x5.dtsi" +#include "at91sam9x5.dtsi" / { model = "Atmel AT91SAM9G35 SoC";
arch/arm/boot/dts/at91sam9g35ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9g35.dtsi" -/include/ "at91sam9x5ek.dtsi" +#include "at91sam9g35.dtsi" +#include "at91sam9x5ek.dtsi" / { model = "Atmel AT91SAM9G35-EK";
arch/arm/boot/dts/at91sam9g45.dtsi +1 -1
@@ -9,7 +9,7 @@ * Licensed under GPLv2 or later. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { model = "Atmel AT91SAM9G45 family SoC";
arch/arm/boot/dts/at91sam9m10g45ek.dts +1 -1
@@ -7,7 +7,7 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9g45.dtsi" +#include "at91sam9g45.dtsi" / { model = "Atmel AT91SAM9M10G45-EK";
arch/arm/boot/dts/at91sam9n12.dtsi +1 -1
@@ -7,7 +7,7 @@ * Licensed under GPLv2 or later. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { model = "Atmel AT91SAM9N12 SoC";
arch/arm/boot/dts/at91sam9n12ek.dts +1 -1
@@ -7,7 +7,7 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9n12.dtsi" +#include "at91sam9n12.dtsi" / { model = "Atmel AT91SAM9N12-EK";
arch/arm/boot/dts/at91sam9x25.dtsi +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ -/include/ "at91sam9x5.dtsi" +#include "at91sam9x5.dtsi" / { model = "Atmel AT91SAM9X25 SoC";
arch/arm/boot/dts/at91sam9x25ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9x25.dtsi" -/include/ "at91sam9x5ek.dtsi" +#include "at91sam9x25.dtsi" +#include "at91sam9x5ek.dtsi" / { model = "Atmel AT91SAM9G25-EK";
arch/arm/boot/dts/at91sam9x35.dtsi +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ -/include/ "at91sam9x5.dtsi" +#include "at91sam9x5.dtsi" / { model = "Atmel AT91SAM9X35 SoC";
arch/arm/boot/dts/at91sam9x35ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9x35.dtsi" -/include/ "at91sam9x5ek.dtsi" +#include "at91sam9x35.dtsi" +#include "at91sam9x5ek.dtsi" / { model = "Atmel AT91SAM9X35-EK";
arch/arm/boot/dts/at91sam9x5.dtsi +1 -1
@@ -9,7 +9,7 @@ * Licensed under GPLv2 or later. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { model = "Atmel AT91SAM9x5 family SoC";
arch/arm/boot/dts/at91sam9x5ek.dtsi +1 -1
@@ -6,7 +6,7 @@ * * Licensed under GPLv2 or later. */ -/include/ "at91sam9x5cm.dtsi" +#include "at91sam9x5cm.dtsi" / { model = "Atmel AT91SAM9X5-EK";
arch/arm/boot/dts/ethernut5.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ /dts-v1/; -/include/ "at91sam9260.dtsi" +#include "at91sam9260.dtsi" / { model = "Ethernut 5";
arch/arm/boot/dts/evk-pro3.dts +2 -2
@@ -9,7 +9,7 @@ /dts-v1/; -/include/ "ge863-pro3.dtsi" +#include "ge863-pro3.dtsi" / { model = "Telit EVK-PRO3 for Telit GE863-PRO3";
@@ -50,4 +50,4 @@ status = "okay"; }; -}; +};
arch/arm/boot/dts/ge863-pro3.dtsi +1 -1
@@ -7,7 +7,7 @@ * Licensed under GPLv2 or later. */ -/include/ "at91sam9260.dtsi" +#include "at91sam9260.dtsi" / { clocks {
arch/arm/boot/dts/kizbox.dts +2 -2
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ /dts-v1/; -/include/ "at91sam9g20.dtsi" +#include "at91sam9g20.dtsi" / {
@@ -137,4 +137,4 @@ gpio-key,wakeup; }; }; -}; +};
arch/arm/boot/dts/mpa1600.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2 only */ /dts-v1/; -/include/ "at91rm9200.dtsi" +#include "at91rm9200.dtsi" / { model = "Phontech MPA 1600";
arch/arm/boot/dts/pm9g45.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ /dts-v1/; -/include/ "at91sam9g45.dtsi" +#include "at91sam9g45.dtsi" / { model = "Ronetix pm9g45";
arch/arm/boot/dts/sama5d3.dtsi +1 -1
@@ -8,7 +8,7 @@ * Licensed under GPLv2 or later. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { model = "Atmel SAMA5D3 family SoC";
arch/arm/boot/dts/sama5d31ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "sama5d3xmb.dtsi" -/include/ "sama5d3xdm.dtsi" +#include "sama5d3xmb.dtsi" +#include "sama5d3xdm.dtsi" / { model = "Atmel SAMA5D31-EK";
arch/arm/boot/dts/sama5d33ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "sama5d3xmb.dtsi" -/include/ "sama5d3xdm.dtsi" +#include "sama5d3xmb.dtsi" +#include "sama5d3xdm.dtsi" / { model = "Atmel SAMA5D33-EK";
arch/arm/boot/dts/sama5d34ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "sama5d3xmb.dtsi" -/include/ "sama5d3xdm.dtsi" +#include "sama5d3xmb.dtsi" +#include "sama5d3xdm.dtsi" / { model = "Atmel SAMA5D34-EK";
arch/arm/boot/dts/sama5d35ek.dts +1 -1
@@ -7,7 +7,7 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "sama5d3xmb.dtsi" +#include "sama5d3xmb.dtsi" / { model = "Atmel SAMA5D35-EK";
arch/arm/boot/dts/sama5d3xcm.dtsi +1 -1
@@ -6,7 +6,7 @@ * * Licensed under GPLv2 or later. */ -/include/ "sama5d3.dtsi" +#include "sama5d3.dtsi" / { compatible = "atmel,samad3xcm", "atmel,sama5d3", "atmel,sama5";
arch/arm/boot/dts/sama5d3xmb.dtsi +1 -1
@@ -6,7 +6,7 @@ * * Licensed under GPLv2 or later. */ -/include/ "sama5d3xcm.dtsi" +#include "sama5d3xcm.dtsi" / { compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
arch/arm/boot/dts/tny_a9260.dts +2 -2
@@ -6,8 +6,8 @@ * Licensed under GPLv2. */ /dts-v1/; -/include/ "at91sam9260.dtsi" -/include/ "tny_a9260_common.dtsi" +#include "at91sam9260.dtsi" +#include "tny_a9260_common.dtsi" / { model = "Calao TNY A9260";
arch/arm/boot/dts/tny_a9263.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2 only */ /dts-v1/; -/include/ "at91sam9263.dtsi" +#include "at91sam9263.dtsi" / { model = "Calao TNY A9263";
arch/arm/boot/dts/tny_a9g20.dts +2 -2
@@ -6,8 +6,8 @@ * Licensed under GPLv2. */ /dts-v1/; -/include/ "at91sam9g20.dtsi" -/include/ "tny_a9260_common.dtsi" +#include "at91sam9g20.dtsi" +#include "tny_a9260_common.dtsi" / { model = "Calao TNY A9G20";
arch/arm/boot/dts/usb_a9260.dts +2 -2
@@ -6,8 +6,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9260.dtsi" -/include/ "usb_a9260_common.dtsi" +#include "at91sam9260.dtsi" +#include "usb_a9260_common.dtsi" / { model = "Calao USB A9260";
arch/arm/boot/dts/usb_a9263.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2 only */ /dts-v1/; -/include/ "at91sam9263.dtsi" +#include "at91sam9263.dtsi" / { model = "Calao USB A9263";
arch/arm/boot/dts/usb_a9g20.dts +2 -2
@@ -6,8 +6,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9g20.dtsi" -/include/ "usb_a9260_common.dtsi" +#include "at91sam9g20.dtsi" +#include "usb_a9260_common.dtsi" / { model = "Calao USB A9G20";
Signature · 1 line
1.7.10.4
PATCH 2/5 ARM: at91: dt: switch to standard GPIO flag defines.
--- arch/arm/boot/dts/aks-cdu.dts | 10 ++++----- arch/arm/boot/dts/animeo_ip.dts | 16 +++++++------- arch/arm/boot/dts/at91-ariag25.dts | 4 ++-- arch/arm/boot/dts/at91rm9200.dtsi | 9 ++++---- arch/arm/boot/dts/at91rm9200ek.dts | 8 +++---- arch/arm/boot/dts/at91sam9260.dtsi | 9 ++++---- arch/arm/boot/dts/at91sam9263.dtsi | 9 ++++---- arch/arm/boot/dts/at91sam9263ek.dts | 18 ++++++++-------- arch/arm/boot/dts/at91sam9g20ek.dts | 4 ++-- arch/arm/boot/dts/at91sam9g20ek_2mmc.dts | 6 +++--- arch/arm/boot/dts/at91sam9g20ek_common.dtsi | 8 +++---- arch/arm/boot/dts/at91sam9g45.dtsi | 9 ++++---- arch/arm/boot/dts/at91sam9m10g45ek.dts | 30 +++++++++++++-------------- arch/arm/boot/dts/at91sam9n12.dtsi | 9 ++++---- arch/arm/boot/dts/at91sam9n12ek.dts | 10 ++++----- arch/arm/boot/dts/at91sam9x5.dtsi | 17 ++++++++------- arch/arm/boot/dts/at91sam9x5cm.dtsi | 6 +++--- arch/arm/boot/dts/at91sam9x5ek.dtsi | 8 +++---- arch/arm/boot/dts/ethernut5.dts | 4 ++-- arch/arm/boot/dts/evk-pro3.dts | 2 +- arch/arm/boot/dts/kizbox.dts | 12 +++++------ arch/arm/boot/dts/mpa1600.dts | 2 +- arch/arm/boot/dts/pm9g45.dts | 14 ++++++------- arch/arm/boot/dts/sama5d3.dtsi | 1 + arch/arm/boot/dts/sama5d31ek.dts | 2 +- arch/arm/boot/dts/sama5d34ek.dts | 2 +- arch/arm/boot/dts/sama5d35ek.dts | 2 +- arch/arm/boot/dts/sama5d3xcm.dtsi | 2 +- arch/arm/boot/dts/sama5d3xmb.dtsi | 12 +++++------ arch/arm/boot/dts/tny_a9263.dts | 2 +- arch/arm/boot/dts/usb_a9260_common.dtsi | 6 +++--- arch/arm/boot/dts/usb_a9263.dts | 6 +++--- arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi | 22 ++++++++++---------- 33 files changed, 144 insertions(+), 137 deletions(-)
arch/arm/boot/dts/aks-cdu.dts +5 -5
@@ -46,7 +46,7 @@ }; usb1: gadget at fffa4000 { - atmel,vbus-gpio = <&pioC 15 0>; + atmel,vbus-gpio = <&pioC 15 GPIO_ACTIVE_HIGH>; status = "okay"; }; };
@@ -90,23 +90,23 @@ compatible = "gpio-leds"; red { - gpios = <&pioC 10 0>; + gpios = <&pioC 10 GPIO_ACTIVE_HIGH>; linux,default-trigger = "none"; }; green { - gpios = <&pioA 5 1>; + gpios = <&pioA 5 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; default-state = "on"; }; yellow { - gpios = <&pioB 20 1>; + gpios = <&pioB 20 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; blue { - gpios = <&pioB 21 1>; + gpios = <&pioB 21 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; };
arch/arm/boot/dts/animeo_ip.dts +8 -8
@@ -123,7 +123,7 @@ usb0: ohci at 00500000 { num-ports = <2>; - atmel,vbus-gpio = <&pioB 15 1>; + atmel,vbus-gpio = <&pioB 15 GPIO_ACTIVE_LOW>; status = "okay"; }; };
@@ -133,23 +133,23 @@ power_green { label = "power_green"; - gpios = <&pioC 17 0>; + gpios = <&pioC 17 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; power_red { label = "power_red"; - gpios = <&pioA 2 0>; + gpios = <&pioA 2 GPIO_ACTIVE_HIGH>; }; tx_green { label = "tx_green"; - gpios = <&pioC 19 0>; + gpios = <&pioC 19 GPIO_ACTIVE_HIGH>; }; tx_red { label = "tx_red"; - gpios = <&pioC 18 0>; + gpios = <&pioC 18 GPIO_ACTIVE_HIGH>; }; };
@@ -160,21 +160,21 @@ keyswitch_in { label = "keyswitch_in"; - gpios = <&pioB 1 0>; + gpios = <&pioB 1 GPIO_ACTIVE_HIGH>; linux,code = <28>; gpio-key,wakeup; }; error_in { label = "error_in"; - gpios = <&pioB 2 0>; + gpios = <&pioB 2 GPIO_ACTIVE_HIGH>; linux,code = <29>; gpio-key,wakeup; }; btn { label = "btn"; - gpios = <&pioC 23 0>; + gpios = <&pioC 23 GPIO_ACTIVE_HIGH>; linux,code = <31>; gpio-key,wakeup; };
arch/arm/boot/dts/at91-ariag25.dts +2 -2
@@ -156,7 +156,7 @@ /* little green LED in middle of Aria G25 module */ aria_led { label = "aria_led"; - gpios = <&pioB 8 0>; /* PB8 */ + gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */ linux,default-trigger = "heartbeat"; };
@@ -164,7 +164,7 @@ onewire at 0 { compatible = "w1-gpio"; - gpios = <&pioA 21 1>; + gpios = <&pioA 21 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_w1_0>; };
arch/arm/boot/dts/at91rm9200.dtsi +5 -4
@@ -11,6 +11,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel AT91RM9200 family SoC";
@@ -503,9 +504,9 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; nand-ecc-mode = "soft"; - gpios = <&pioC 2 0 + gpios = <&pioC 2 GPIO_ACTIVE_HIGH 0 - &pioB 1 0 + &pioB 1 GPIO_ACTIVE_HIGH >; status = "disabled"; };
@@ -520,8 +521,8 @@ i2c at 0 { compatible = "i2c-gpio"; - gpios = <&pioA 25 0 /* sda */ - &pioA 26 0 /* scl */ + gpios = <&pioA 25 GPIO_ACTIVE_HIGH /* sda */ + &pioA 26 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
arch/arm/boot/dts/at91rm9200ek.dts +4 -4
@@ -50,7 +50,7 @@ }; usb1: gadget at fffb0000 { - atmel,vbus-gpio = <&pioD 4 0>; + atmel,vbus-gpio = <&pioD 4 GPIO_ACTIVE_HIGH>; status = "okay"; }; };
@@ -66,19 +66,19 @@ ds2 { label = "green"; - gpios = <&pioB 0 0x1>; + gpios = <&pioB 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "mmc0"; }; ds4 { label = "yellow"; - gpios = <&pioB 1 0x1>; + gpios = <&pioB 1 GPIO_ACTIVE_LOW>; linux,default-trigger = "heartbeat"; }; ds6 { label = "red"; - gpios = <&pioB 2 0x1>; + gpios = <&pioB 2 GPIO_ACTIVE_LOW>; }; }; };
arch/arm/boot/dts/at91sam9260.dtsi +5 -4
@@ -9,6 +9,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel AT91SAM9260 family SoC";
@@ -567,8 +568,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioC 13 0 - &pioC 14 0 + gpios = <&pioC 13 GPIO_ACTIVE_HIGH + &pioC 14 GPIO_ACTIVE_HIGH 0 >; status = "disabled";
@@ -584,8 +585,8 @@ i2c at 0 { compatible = "i2c-gpio"; - gpios = <&pioA 23 0 /* sda */ - &pioA 24 0 /* scl */ + gpios = <&pioA 23 GPIO_ACTIVE_HIGH /* sda */ + &pioA 24 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
arch/arm/boot/dts/at91sam9263.dtsi +5 -4
@@ -7,6 +7,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel AT91SAM9263 family SoC";
@@ -515,8 +516,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioA 22 0 - &pioD 15 0 + gpios = <&pioA 22 GPIO_ACTIVE_HIGH + &pioD 15 GPIO_ACTIVE_HIGH 0 >; status = "disabled";
@@ -532,8 +533,8 @@ i2c at 0 { compatible = "i2c-gpio"; - gpios = <&pioB 4 0 /* sda */ - &pioB 5 0 /* scl */ + gpios = <&pioB 4 GPIO_ACTIVE_HIGH /* sda */ + &pioB 5 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
arch/arm/boot/dts/at91sam9263ek.dts +9 -9
@@ -51,7 +51,7 @@ }; usb1: gadget at fff78000 { - atmel,vbus-gpio = <&pioA 25 0>; + atmel,vbus-gpio = <&pioA 25 GPIO_ACTIVE_HIGH>; status = "okay"; };
@@ -65,8 +65,8 @@ slot at 0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioE 18 0>; - wp-gpios = <&pioE 19 0>; + cd-gpios = <&pioE 18 GPIO_ACTIVE_HIGH>; + wp-gpios = <&pioE 19 GPIO_ACTIVE_HIGH>; }; };
@@ -141,8 +141,8 @@ usb0: ohci at 00a00000 { num-ports = <2>; status = "okay"; - atmel,vbus-gpio = <&pioA 24 0 - &pioA 21 0 + atmel,vbus-gpio = <&pioA 24 GPIO_ACTIVE_HIGH + &pioA 21 GPIO_ACTIVE_HIGH >; }; };
@@ -152,13 +152,13 @@ d3 { label = "d3"; - gpios = <&pioB 7 0>; + gpios = <&pioB 7 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; d2 { label = "d2"; - gpios = <&pioC 29 1>; + gpios = <&pioC 29 GPIO_ACTIVE_LOW>; linux,default-trigger = "nand-disk"; }; };
@@ -168,14 +168,14 @@ left_click { label = "left_click"; - gpios = <&pioC 5 1>; + gpios = <&pioC 5 GPIO_ACTIVE_LOW>; linux,code = <272>; gpio-key,wakeup; }; right_click { label = "right_click"; - gpios = <&pioC 4 1>; + gpios = <&pioC 4 GPIO_ACTIVE_LOW>; linux,code = <273>; gpio-key,wakeup; };
arch/arm/boot/dts/at91sam9g20ek.dts +2 -2
@@ -17,13 +17,13 @@ ds1 { label = "ds1"; - gpios = <&pioA 9 0>; + gpios = <&pioA 9 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; ds5 { label = "ds5"; - gpios = <&pioA 6 1>; + gpios = <&pioA 6 GPIO_ACTIVE_LOW>; }; }; };
arch/arm/boot/dts/at91sam9g20ek_2mmc.dts +3 -3
@@ -23,7 +23,7 @@ slot at 0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioC 2 0>; + cd-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; }; };
@@ -43,13 +43,13 @@ ds1 { label = "ds1"; - gpios = <&pioB 9 0>; + gpios = <&pioB 9 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; ds5 { label = "ds5"; - gpios = <&pioB 8 1>; + gpios = <&pioB 8 GPIO_ACTIVE_LOW>; }; }; };
arch/arm/boot/dts/at91sam9g20ek_common.dtsi +4 -4
@@ -65,7 +65,7 @@ }; usb1: gadget at fffa4000 { - atmel,vbus-gpio = <&pioC 5 0>; + atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>; status = "okay"; };
@@ -79,7 +79,7 @@ slot at 1 { reg = <1>; bus-width = <4>; - cd-gpios = <&pioC 9 0>; + cd-gpios = <&pioC 9 GPIO_ACTIVE_HIGH>; }; };
@@ -180,14 +180,14 @@ btn3 { label = "Button 3"; - gpios = <&pioA 30 1>; + gpios = <&pioA 30 GPIO_ACTIVE_LOW>; linux,code = <0x103>; gpio-key,wakeup; }; btn4 { label = "Button 4"; - gpios = <&pioA 31 1>; + gpios = <&pioA 31 GPIO_ACTIVE_LOW>; linux,code = <0x104>; gpio-key,wakeup; };
arch/arm/boot/dts/at91sam9g45.dtsi +5 -4
@@ -10,6 +10,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel AT91SAM9G45 family SoC";
@@ -592,8 +593,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioC 8 0 - &pioC 14 0 + gpios = <&pioC 8 GPIO_ACTIVE_HIGH + &pioC 14 GPIO_ACTIVE_HIGH 0 >; status = "disabled";
@@ -616,8 +617,8 @@ i2c at 0 { compatible = "i2c-gpio"; - gpios = <&pioA 20 0 /* sda */ - &pioA 21 0 /* scl */ + gpios = <&pioA 20 GPIO_ACTIVE_HIGH /* sda */ + &pioA 21 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
arch/arm/boot/dts/at91sam9m10g45ek.dts +15 -15
@@ -68,7 +68,7 @@ slot at 0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 10 0>; + cd-gpios = <&pioD 10 GPIO_ACTIVE_HIGH>; }; };
@@ -81,8 +81,8 @@ slot at 0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 11 0>; - wp-gpios = <&pioD 29 0>; + cd-gpios = <&pioD 11 GPIO_ACTIVE_HIGH>; + wp-gpios = <&pioD 29 GPIO_ACTIVE_HIGH>; }; };
@@ -139,8 +139,8 @@ usb0: ohci at 00700000 { status = "okay"; num-ports = <2>; - atmel,vbus-gpio = <&pioD 1 1 - &pioD 3 1>; + atmel,vbus-gpio = <&pioD 1 GPIO_ACTIVE_LOW + &pioD 3 GPIO_ACTIVE_LOW>; }; usb1: ehci at 00800000 {
@@ -153,19 +153,19 @@ d8 { label = "d8"; - gpios = <&pioD 30 0>; + gpios = <&pioD 30 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; d6 { label = "d6"; - gpios = <&pioD 0 1>; + gpios = <&pioD 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "nand-disk"; }; d7 { label = "d7"; - gpios = <&pioD 31 1>; + gpios = <&pioD 31 GPIO_ACTIVE_LOW>; linux,default-trigger = "mmc0"; }; };
@@ -175,45 +175,45 @@ left_click { label = "left_click"; - gpios = <&pioB 6 1>; + gpios = <&pioB 6 GPIO_ACTIVE_LOW>; linux,code = <272>; gpio-key,wakeup; }; right_click { label = "right_click"; - gpios = <&pioB 7 1>; + gpios = <&pioB 7 GPIO_ACTIVE_LOW>; linux,code = <273>; gpio-key,wakeup; }; left { label = "Joystick Left"; - gpios = <&pioB 14 1>; + gpios = <&pioB 14 GPIO_ACTIVE_LOW>; linux,code = <105>; }; right { label = "Joystick Right"; - gpios = <&pioB 15 1>; + gpios = <&pioB 15 GPIO_ACTIVE_LOW>; linux,code = <106>; }; up { label = "Joystick Up"; - gpios = <&pioB 16 1>; + gpios = <&pioB 16 GPIO_ACTIVE_LOW>; linux,code = <103>; }; down { label = "Joystick Down"; - gpios = <&pioB 17 1>; + gpios = <&pioB 17 GPIO_ACTIVE_LOW>; linux,code = <108>; }; enter { label = "Joystick Press"; - gpios = <&pioB 18 1>; + gpios = <&pioB 18 GPIO_ACTIVE_LOW>; linux,code = <28>; }; };
arch/arm/boot/dts/at91sam9n12.dtsi +5 -4
@@ -8,6 +8,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel AT91SAM9N12 SoC";
@@ -438,8 +439,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioD 5 0 - &pioD 4 0 + gpios = <&pioD 5 GPIO_ACTIVE_HIGH + &pioD 4 GPIO_ACTIVE_HIGH 0 >; status = "disabled";
@@ -455,8 +456,8 @@ i2c at 0 { compatible = "i2c-gpio"; - gpios = <&pioA 30 0 /* sda */ - &pioA 31 0 /* scl */ + gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */ + &pioA 31 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
arch/arm/boot/dts/at91sam9n12ek.dts +5 -5
@@ -55,7 +55,7 @@ slot at 0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioA 7 0>; + cd-gpios = <&pioA 7 GPIO_ACTIVE_HIGH>; }; };
@@ -95,19 +95,19 @@ d8 { label = "d8"; - gpios = <&pioB 4 1>; + gpios = <&pioB 4 GPIO_ACTIVE_LOW>; linux,default-trigger = "mmc0"; }; d9 { label = "d6"; - gpios = <&pioB 5 1>; + gpios = <&pioB 5 GPIO_ACTIVE_LOW>; linux,default-trigger = "nand-disk"; }; d10 { label = "d7"; - gpios = <&pioB 6 0>; + gpios = <&pioB 6 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; };
@@ -117,7 +117,7 @@ enter { label = "Enter"; - gpios = <&pioB 4 1>; + gpios = <&pioB 4 GPIO_ACTIVE_LOW>; linux,code = <28>; gpio-key,wakeup; };
arch/arm/boot/dts/at91sam9x5.dtsi +9 -8
@@ -10,6 +10,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel AT91SAM9x5 family SoC";
@@ -664,8 +665,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioD 5 0 - &pioD 4 0 + gpios = <&pioD 5 GPIO_ACTIVE_HIGH + &pioD 4 GPIO_ACTIVE_HIGH 0 >; status = "disabled";
@@ -688,8 +689,8 @@ i2c at 0 { compatible = "i2c-gpio"; - gpios = <&pioA 30 0 /* sda */ - &pioA 31 0 /* scl */ + gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */ + &pioA 31 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
@@ -703,8 +704,8 @@ i2c at 1 { compatible = "i2c-gpio"; - gpios = <&pioC 0 0 /* sda */ - &pioC 1 0 /* scl */ + gpios = <&pioC 0 GPIO_ACTIVE_HIGH /* sda */ + &pioC 1 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
@@ -718,8 +719,8 @@ i2c at 2 { compatible = "i2c-gpio"; - gpios = <&pioB 4 0 /* sda */ - &pioB 5 0 /* scl */ + gpios = <&pioB 4 GPIO_ACTIVE_HIGH /* sda */ + &pioB 5 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
arch/arm/boot/dts/at91sam9x5cm.dtsi +3 -3
@@ -75,19 +75,19 @@ pb18 { label = "pb18"; - gpios = <&pioB 18 1>; + gpios = <&pioB 18 GPIO_ACTIVE_LOW>; linux,default-trigger = "heartbeat"; }; pd21 { label = "pd21"; - gpios = <&pioD 21 0>; + gpios = <&pioD 21 GPIO_ACTIVE_HIGH>; }; }; 1wire_cm { compatible = "w1-gpio"; - gpios = <&pioB 18 0>; + gpios = <&pioB 18 GPIO_ACTIVE_HIGH>; linux,open-drain; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_1wire_cm>;
arch/arm/boot/dts/at91sam9x5ek.dtsi +4 -4
@@ -27,7 +27,7 @@ slot at 0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 15 0>; + cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>; }; };
@@ -40,7 +40,7 @@ slot at 0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 14 0>; + cd-gpios = <&pioD 14 GPIO_ACTIVE_HIGH>; }; };
@@ -86,8 +86,8 @@ usb0: ohci at 00600000 { status = "okay"; num-ports = <2>; - atmel,vbus-gpio = <&pioD 19 1 - &pioD 20 1 + atmel,vbus-gpio = <&pioD 19 GPIO_ACTIVE_LOW + &pioD 20 GPIO_ACTIVE_LOW >; };
arch/arm/boot/dts/ethernut5.dts +2 -2
@@ -40,7 +40,7 @@ }; usb1: gadget at fffa4000 { - atmel,vbus-gpio = <&pioC 5 0>; + atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>; status = "okay"; }; };
@@ -52,7 +52,7 @@ status = "okay"; gpios = <0 - &pioC 14 0 + &pioC 14 GPIO_ACTIVE_HIGH 0 >;
arch/arm/boot/dts/evk-pro3.dts +1 -1
@@ -31,7 +31,7 @@ }; usb1: gadget at fffa4000 { - atmel,vbus-gpio = <&pioC 5 0>; + atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>; status = "okay"; };
arch/arm/boot/dts/kizbox.dts +6 -6
@@ -94,26 +94,26 @@ led1g { label = "led1:green"; - gpios = <&pioB 0 1>; + gpios = <&pioB 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; led1r { label = "led1:red"; - gpios = <&pioB 1 1>; + gpios = <&pioB 1 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; led2g { label = "led2:green"; - gpios = <&pioB 2 1>; + gpios = <&pioB 2 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; default-state = "on"; }; led2r { label = "led2:red"; - gpios = <&pioB 3 1>; + gpios = <&pioB 3 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; };
@@ -125,14 +125,14 @@ reset { label = "reset"; - gpios = <&pioB 30 1>; + gpios = <&pioB 30 GPIO_ACTIVE_LOW>; linux,code = <0x100>; gpio-key,wakeup; }; mode { label = "mode"; - gpios = <&pioB 31 1>; + gpios = <&pioB 31 GPIO_ACTIVE_LOW>; linux,code = <0x101>; gpio-key,wakeup; };
arch/arm/boot/dts/mpa1600.dts +1 -1
@@ -62,7 +62,7 @@ monitor_mute { label = "Monitor mute"; - gpios = <&pioC 1 1>; + gpios = <&pioC 1 GPIO_ACTIVE_LOW>; linux,code = <113>; }; };
arch/arm/boot/dts/pm9g45.dts +7 -7
@@ -64,7 +64,7 @@ slot at 0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 6 0>; + cd-gpios = <&pioD 6 GPIO_ACTIVE_HIGH>; }; };
@@ -81,8 +81,8 @@ nand-on-flash-bbt; pinctrl-0 = <&pinctrl_board_nand>; - gpios = <&pioD 3 0 - &pioC 14 0 + gpios = <&pioD 3 GPIO_ACTIVE_HIGH + &pioC 14 GPIO_ACTIVE_HIGH 0 >;
@@ -134,13 +134,13 @@ led0 { label = "led0"; - gpios = <&pioD 0 1>; + gpios = <&pioD 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "nand-disk"; }; led1 { label = "led1"; - gpios = <&pioD 31 0>; + gpios = <&pioD 31 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; };
@@ -152,13 +152,13 @@ right { label = "SW4"; - gpios = <&pioE 7 1>; + gpios = <&pioE 7 GPIO_ACTIVE_LOW>; linux,code = <106>; }; up { label = "SW3"; - gpios = <&pioE 8 1>; + gpios = <&pioE 8 GPIO_ACTIVE_LOW>; linux,code = <103>; }; };
arch/arm/boot/dts/sama5d3.dtsi +1 -0
@@ -9,6 +9,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel SAMA5D3 family SoC";
arch/arm/boot/dts/sama5d31ek.dts +1 -1
@@ -41,7 +41,7 @@ leds { d3 { label = "d3"; - gpios = <&pioE 24 0>; + gpios = <&pioE 24 GPIO_ACTIVE_HIGH>; }; };
arch/arm/boot/dts/sama5d34ek.dts +1 -1
@@ -51,7 +51,7 @@ leds { d3 { label = "d3"; - gpios = <&pioE 24 0>; + gpios = <&pioE 24 GPIO_ACTIVE_HIGH>; }; };
arch/arm/boot/dts/sama5d35ek.dts +1 -1
@@ -48,7 +48,7 @@ pb_user1 { label = "pb_user1"; - gpios = <&pioE 27 0>; + gpios = <&pioE 27 GPIO_ACTIVE_HIGH>; linux,code = <0x100>; gpio-key,wakeup; };
arch/arm/boot/dts/sama5d3xcm.dtsi +1 -1
@@ -85,7 +85,7 @@ d2 { label = "d2"; - gpios = <&pioE 25 1>; /* PE25, conflicts with A25, RXD2 */ + gpios = <&pioE 25 GPIO_ACTIVE_LOW>; /* PE25, conflicts with A25, RXD2 */ }; }; };
arch/arm/boot/dts/sama5d3xmb.dtsi +6 -6
@@ -20,7 +20,7 @@ slot at 0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 17 0>; + cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>; }; };
@@ -62,7 +62,7 @@ slot at 0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 18 0>; + cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>; }; };
@@ -127,7 +127,7 @@ }; usb0: gadget at 00500000 { - atmel,vbus-gpio = <&pioD 29 0>; + atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usba_vbus>; status = "okay";
@@ -135,9 +135,9 @@ usb1: ohci at 00600000 { num-ports = <3>; - atmel,vbus-gpio = <&pioD 25 0 - &pioD 26 1 - &pioD 27 1 + atmel,vbus-gpio = <&pioD 25 GPIO_ACTIVE_HIGH + &pioD 26 GPIO_ACTIVE_LOW + &pioD 27 GPIO_ACTIVE_LOW >; status = "okay"; };
arch/arm/boot/dts/tny_a9263.dts +1 -1
@@ -38,7 +38,7 @@ }; usb1: gadget at fff78000 { - atmel,vbus-gpio = <&pioB 11 0>; + atmel,vbus-gpio = <&pioB 11 GPIO_ACTIVE_HIGH>; status = "okay"; }; };
arch/arm/boot/dts/usb_a9260_common.dtsi +3 -3
@@ -30,7 +30,7 @@ }; usb1: gadget at fffa4000 { - atmel,vbus-gpio = <&pioC 5 0>; + atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>; status = "okay"; }; };
@@ -93,7 +93,7 @@ user_led { label = "user_led"; - gpios = <&pioB 21 1>; + gpios = <&pioB 21 GPIO_ACTIVE_LOW>; linux,default-trigger = "heartbeat"; }; };
@@ -105,7 +105,7 @@ user_pb { label = "user_pb"; - gpios = <&pioB 10 1>; + gpios = <&pioB 10 GPIO_ACTIVE_LOW>; linux,code = <28>; gpio-key,wakeup; };
arch/arm/boot/dts/usb_a9263.dts +3 -3
@@ -43,7 +43,7 @@ }; usb1: gadget at fff78000 { - atmel,vbus-gpio = <&pioB 11 0>; + atmel,vbus-gpio = <&pioB 11 GPIO_ACTIVE_HIGH>; status = "okay"; };
@@ -107,7 +107,7 @@ user_led { label = "user_led"; - gpios = <&pioB 21 0>; + gpios = <&pioB 21 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; };
@@ -119,7 +119,7 @@ user_pb { label = "user_pb"; - gpios = <&pioB 10 1>; + gpios = <&pioB 10 GPIO_ACTIVE_LOW>; linux,code = <28>; gpio-key,wakeup; };
arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi +11 -11
@@ -28,39 +28,39 @@ user_led1 { label = "user_led1"; - gpios = <&pioB 20 1>; + gpios = <&pioB 20 GPIO_ACTIVE_LOW>; }; /* * led already used by mother board but active as high * user_led2 { * label = "user_led2"; -* gpios = <&pioB 21 1>; +* gpios = <&pioB 21 GPIO_ACTIVE_LOW>; * }; */ user_led3 { label = "user_led3"; - gpios = <&pioB 22 1>; + gpios = <&pioB 22 GPIO_ACTIVE_LOW>; }; user_led4 { label = "user_led4"; - gpios = <&pioB 23 1>; + gpios = <&pioB 23 GPIO_ACTIVE_LOW>; }; red { label = "red"; - gpios = <&pioB 24 1>; + gpios = <&pioB 24 GPIO_ACTIVE_LOW>; }; orange { label = "orange"; - gpios = <&pioB 30 1>; + gpios = <&pioB 30 GPIO_ACTIVE_LOW>; }; green { label = "green"; - gpios = <&pioB 31 1>; + gpios = <&pioB 31 GPIO_ACTIVE_LOW>; }; };
@@ -71,25 +71,25 @@ user_pb1 { label = "user_pb1"; - gpios = <&pioB 25 1>; + gpios = <&pioB 25 GPIO_ACTIVE_LOW>; linux,code = <0x100>; }; user_pb2 { label = "user_pb2"; - gpios = <&pioB 13 1>; + gpios = <&pioB 13 GPIO_ACTIVE_LOW>; linux,code = <0x101>; }; user_pb3 { label = "user_pb3"; - gpios = <&pioA 26 1>; + gpios = <&pioA 26 GPIO_ACTIVE_LOW>; linux,code = <0x102>; }; user_pb4 { label = "user_pb4"; - gpios = <&pioC 9 1>; + gpios = <&pioC 9 GPIO_ACTIVE_LOW>; linux,code = <0x103>; }; };
Signature · 1 line
1.7.10.4
PATCH 3/5 ARM: at91: dt: add pinctrl pre-processor define
In reply to Jean-Christophe PLAGNIOL-VILLARD--- include/dt-bindings/pinctrl/at91.h | 35 +++++++++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+) create mode 100644 include/dt-bindings/pinctrl/at91.h
include/dt-bindings/pinctrl/at91.h new file +35 -0
@@ -0,0 +1,35 @@ +/* +* This header provides constants for most at91 pinctrl bindings. +* +* Copyright (C) 2013 Jean-Christophe PLAGNIOL-VILLARD <[email protected]> +* +* GPLv2 only +*/ + +#ifndef __DT_BINDINGS_AT91_PINCTRL_H__ +#define __DT_BINDINGS_AT91_PINCTRL_H__ + +#define AT91_PINCTRL_NONE (0 << 0) +#define AT91_PINCTRL_PULL_UP (1 << 0) +#define AT91_PINCTRL_MULTI_DRIVE (1 << 1) +#define AT91_PINCTRL_DEGLITCH (1 << 2) +#define AT91_PINCTRL_PULL_DOWN (1 << 3) +#define AT91_PINCTRL_DIS_SCHMIT (1 << 4) +#define AT91_PINCTRL_DEBOUNCE (1 << 16) +#define AT91_PINCTRL_DEBOUNCE_VA (x) (x << 17) + +#define AT91_PINCTRL_PULL_UP_DEGLITCH (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DEGLITCH) + +#define AT91_PIOA 0 +#define AT91_PIOB 1 +#define AT91_PIOC 2 +#define AT91_PIOD 3 +#define AT91_PIOE 4 + +#define AT91_PERIPH_GPIO 0 +#define AT91_PERIPH_A 1 +#define AT91_PERIPH_B 2 +#define AT91_PERIPH_C 3 +#define AT91_PERIPH_D 4 + +#endif /* __DT_BINDINGS_AT91_PINCTRL_H__ */
Signature · 1 line
1.7.10.4
PATCH 3/5 ARM: at91: dt: add pinctrl pre-processor define
Quoted 2 lines · Jean-Christophe PLAGNIOL-VILLARD
Signed-off-by Jean-Christophe PLAGNIOL-VILLARD <[email protected]>Cc Nicolas Ferre <[email protected]>
Thanks, this makes the device trees much more readable.
Yours,
Linus Walleij
PATCH 5/5 ARM: at91: dt: switch to standard IRQ flag defines
In reply to Jean-Christophe PLAGNIOL-VILLARD--- arch/arm/boot/dts/at91rm9200.dtsi | 45 +++++++++++--------- arch/arm/boot/dts/at91sam9260.dtsi | 49 ++++++++++++---------- arch/arm/boot/dts/at91sam9263.dtsi | 43 ++++++++++---------- arch/arm/boot/dts/at91sam9g45.dtsi | 49 +++++++++++----------- arch/arm/boot/dts/at91sam9n12.dtsi | 41 ++++++++++--------- arch/arm/boot/dts/at91sam9x5.dtsi | 55 +++++++++++++------------ arch/arm/boot/dts/sama5d3.dtsi | 79 ++++++++++++++++++------------------ 7 files changed, 188 insertions(+), 173 deletions(-)
arch/arm/boot/dts/at91rm9200.dtsi +25 -20
@@ -12,6 +12,7 @@ #include "skeleton.dtsi" #include <dt-bindings/pinctrl/at91.h> +#include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/gpio/gpio.h> / {
@@ -79,25 +80,29 @@ st: timer at fffffd00 { compatible = "atmel,at91rm9200-st"; reg = <0xfffffd00 0x100>; - interrupts = <1 4 7>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; }; tcb0: timer at fffa0000 { compatible = "atmel,at91rm9200-tcb"; reg = <0xfffa0000 0x100>; - interrupts = <17 4 0 18 4 0 19 4 0>; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0 + 18 IRQ_TYPE_LEVEL_HIGH 0 + 19 IRQ_TYPE_LEVEL_HIGH 0>; }; tcb1: timer at fffa4000 { compatible = "atmel,at91rm9200-tcb"; reg = <0xfffa4000 0x100>; - interrupts = <20 4 0 21 4 0 22 4 0>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0 + 21 IRQ_TYPE_LEVEL_HIGH 0 + 22 IRQ_TYPE_LEVEL_HIGH 0>; }; i2c0: i2c at fffb8000 { compatible = "atmel,at91rm9200-i2c"; reg = <0xfffb8000 0x4000>; - interrupts = <12 4 6>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 6>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_twi>; #address-cells = <1>;
@@ -108,7 +113,7 @@ mmc0: mmc at fffb4000 { compatible = "atmel,hsmci"; reg = <0xfffb4000 0x4000>; - interrupts = <10 4 0>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 0>; #address-cells = <1>; #size-cells = <0>; status = "disabled";
@@ -117,7 +122,7 @@ ssc0: ssc at fffd0000 { compatible = "atmel,at91rm9200-ssc"; reg = <0xfffd0000 0x4000>; - interrupts = <14 4 5>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; status = "disable";
@@ -126,7 +131,7 @@ ssc1: ssc at fffd4000 { compatible = "atmel,at91rm9200-ssc"; reg = <0xfffd4000 0x4000>; - interrupts = <15 4 5>; + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; status = "disable";
@@ -135,7 +140,7 @@ ssc2: ssc at fffd8000 { compatible = "atmel,at91rm9200-ssc"; reg = <0xfffd8000 0x4000>; - interrupts = <16 4 5>; + interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc2_tx &pinctrl_ssc2_rx>; status = "disable";
@@ -144,7 +149,7 @@ macb0: ethernet at fffbc000 { compatible = "cdns,at91rm9200-emac", "cdns,emac"; reg = <0xfffbc000 0x4000>; - interrupts = <24 4 3>; + interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3>; phy-mode = "rmii"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_macb_rmii>;
@@ -396,7 +401,7 @@ pioA: gpio at fffff400 { compatible = "atmel,at91rm9200-gpio"; reg = <0xfffff400 0x200>; - interrupts = <2 4 1>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>; #gpio-cells = <2>; gpio-controller; interrupt-controller;
@@ -406,7 +411,7 @@ pioB: gpio at fffff600 { compatible = "atmel,at91rm9200-gpio"; reg = <0xfffff600 0x200>; - interrupts = <3 4 1>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>; #gpio-cells = <2>; gpio-controller; interrupt-controller;
@@ -416,7 +421,7 @@ pioC: gpio at fffff800 { compatible = "atmel,at91rm9200-gpio"; reg = <0xfffff800 0x200>; - interrupts = <4 4 1>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>; #gpio-cells = <2>; gpio-controller; interrupt-controller;
@@ -426,7 +431,7 @@ pioD: gpio at fffffa00 { compatible = "atmel,at91rm9200-gpio"; reg = <0xfffffa00 0x200>; - interrupts = <5 4 1>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH 1>; #gpio-cells = <2>; gpio-controller; interrupt-controller;
@@ -437,7 +442,7 @@ dbgu: serial at fffff200 { compatible = "atmel,at91rm9200-usart"; reg = <0xfffff200 0x200>; - interrupts = <1 4 7>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_dbgu>; status = "disabled";
@@ -446,7 +451,7 @@ usart0: serial at fffc0000 { compatible = "atmel,at91rm9200-usart"; reg = <0xfffc0000 0x200>; - interrupts = <6 4 5>; + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>; atmel,use-dma-rx; atmel,use-dma-tx; pinctrl-names = "default";
@@ -457,7 +462,7 @@ usart1: serial at fffc4000 { compatible = "atmel,at91rm9200-usart"; reg = <0xfffc4000 0x200>; - interrupts = <7 4 5>; + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>; atmel,use-dma-rx; atmel,use-dma-tx; pinctrl-names = "default";
@@ -468,7 +473,7 @@ usart2: serial at fffc8000 { compatible = "atmel,at91rm9200-usart"; reg = <0xfffc8000 0x200>; - interrupts = <8 4 5>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>; atmel,use-dma-rx; atmel,use-dma-tx; pinctrl-names = "default";
@@ -479,7 +484,7 @@ usart3: serial at fffcc000 { compatible = "atmel,at91rm9200-usart"; reg = <0xfffcc000 0x200>; - interrupts = <23 4 5>; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH 5>; atmel,use-dma-rx; atmel,use-dma-tx; pinctrl-names = "default";
@@ -490,7 +495,7 @@ usb1: gadget at fffb0000 { compatible = "atmel,at91rm9200-udc"; reg = <0xfffb0000 0x4000>; - interrupts = <11 4 2>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 2>; status = "disabled"; }; };
@@ -515,7 +520,7 @@ usb0: ohci at 00300000 { compatible = "atmel,at91rm9200-ohci", "usb-ohci"; reg = <0x00300000 0x100000>; - interrupts = <23 4 2>; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>; status = "disabled"; }; };
arch/arm/boot/dts/at91sam9260.dtsi +27 -22
185 lines not on this page · raw message
arch/arm/boot/dts/at91sam9263.dtsi +22 -21
174 lines not on this page · raw message
arch/arm/boot/dts/at91sam9g45.dtsi +25 -24
197 lines not on this page · raw message
arch/arm/boot/dts/at91sam9n12.dtsi +21 -20
165 lines not on this page · raw message
arch/arm/boot/dts/at91sam9x5.dtsi +28 -27
220 lines not on this page · raw message
arch/arm/boot/dts/sama5d3.dtsi +40 -39
316 lines not on this page · raw message
Signature · 1 line
1.7.10.4
PATCH 1/5 ARM: at91: dt: use #include for all device trees
In reply to Jean-Christophe PLAGNIOL-VILLARDto prepare the switch to the macro.
--- arch/arm/boot/dts/aks-cdu.dts | 2 +- arch/arm/boot/dts/animeo_ip.dts | 2 +- arch/arm/boot/dts/at91-ariag25.dts | 2 +- arch/arm/boot/dts/at91rm9200.dtsi | 2 +- arch/arm/boot/dts/at91rm9200ek.dts | 2 +- arch/arm/boot/dts/at91sam9260.dtsi | 2 +- arch/arm/boot/dts/at91sam9263.dtsi | 2 +- arch/arm/boot/dts/at91sam9263ek.dts | 2 +- arch/arm/boot/dts/at91sam9g15.dtsi | 2 +- arch/arm/boot/dts/at91sam9g15ek.dts | 4 ++-- arch/arm/boot/dts/at91sam9g20.dtsi | 2 +- arch/arm/boot/dts/at91sam9g20ek.dts | 2 +- arch/arm/boot/dts/at91sam9g20ek_2mmc.dts | 2 +- arch/arm/boot/dts/at91sam9g20ek_common.dtsi | 2 +- arch/arm/boot/dts/at91sam9g25.dtsi | 2 +- arch/arm/boot/dts/at91sam9g25ek.dts | 4 ++-- arch/arm/boot/dts/at91sam9g35.dtsi | 2 +- arch/arm/boot/dts/at91sam9g35ek.dts | 4 ++-- arch/arm/boot/dts/at91sam9g45.dtsi | 2 +- arch/arm/boot/dts/at91sam9m10g45ek.dts | 2 +- arch/arm/boot/dts/at91sam9n12.dtsi | 2 +- arch/arm/boot/dts/at91sam9n12ek.dts | 2 +- arch/arm/boot/dts/at91sam9x25.dtsi | 2 +- arch/arm/boot/dts/at91sam9x25ek.dts | 4 ++-- arch/arm/boot/dts/at91sam9x35.dtsi | 2 +- arch/arm/boot/dts/at91sam9x35ek.dts | 4 ++-- arch/arm/boot/dts/at91sam9x5.dtsi | 2 +- arch/arm/boot/dts/at91sam9x5ek.dtsi | 2 +- arch/arm/boot/dts/ethernut5.dts | 2 +- arch/arm/boot/dts/evk-pro3.dts | 4 ++-- arch/arm/boot/dts/ge863-pro3.dtsi | 2 +- arch/arm/boot/dts/kizbox.dts | 4 ++-- arch/arm/boot/dts/mpa1600.dts | 2 +- arch/arm/boot/dts/pm9g45.dts | 2 +- arch/arm/boot/dts/sama5d3.dtsi | 2 +- arch/arm/boot/dts/sama5d31ek.dts | 4 ++-- arch/arm/boot/dts/sama5d33ek.dts | 4 ++-- arch/arm/boot/dts/sama5d34ek.dts | 4 ++-- arch/arm/boot/dts/sama5d35ek.dts | 2 +- arch/arm/boot/dts/sama5d3xcm.dtsi | 2 +- arch/arm/boot/dts/sama5d3xmb.dtsi | 2 +- arch/arm/boot/dts/tny_a9260.dts | 4 ++-- arch/arm/boot/dts/tny_a9263.dts | 2 +- arch/arm/boot/dts/tny_a9g20.dts | 4 ++-- arch/arm/boot/dts/usb_a9260.dts | 4 ++-- arch/arm/boot/dts/usb_a9263.dts | 2 +- arch/arm/boot/dts/usb_a9g20.dts | 4 ++-- 47 files changed, 61 insertions(+), 61 deletions(-)
arch/arm/boot/dts/aks-cdu.dts +1 -1
@@ -9,7 +9,7 @@ /dts-v1/; -/include/ "ge863-pro3.dtsi" +#include "ge863-pro3.dtsi" / { chosen {
arch/arm/boot/dts/animeo_ip.dts +1 -1
@@ -7,7 +7,7 @@ */ /dts-v1/; -/include/ "at91sam9260.dtsi" +#include "at91sam9260.dtsi" / { model = "Somfy Animeo IP";
arch/arm/boot/dts/at91-ariag25.dts +1 -1
@@ -7,7 +7,7 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9g25.dtsi" +#include "at91sam9g25.dtsi" / { model = "Acme Systems Aria G25";
arch/arm/boot/dts/at91rm9200.dtsi +1 -1
@@ -10,7 +10,7 @@ * Licensed under GPLv2 or later. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { model = "Atmel AT91RM9200 family SoC";
arch/arm/boot/dts/at91rm9200ek.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2 only */ /dts-v1/; -/include/ "at91rm9200.dtsi" +#include "at91rm9200.dtsi" / { model = "Atmel AT91RM9200 evaluation kit";
arch/arm/boot/dts/at91sam9260.dtsi +1 -1
@@ -8,7 +8,7 @@ * Licensed under GPLv2 or later. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { model = "Atmel AT91SAM9260 family SoC";
arch/arm/boot/dts/at91sam9263.dtsi +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2 only. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { model = "Atmel AT91SAM9263 family SoC";
arch/arm/boot/dts/at91sam9263ek.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2 only */ /dts-v1/; -/include/ "at91sam9263.dtsi" +#include "at91sam9263.dtsi" / { model = "Atmel at91sam9263ek";
arch/arm/boot/dts/at91sam9g15.dtsi +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ -/include/ "at91sam9x5.dtsi" +#include "at91sam9x5.dtsi" / { model = "Atmel AT91SAM9G15 SoC";
arch/arm/boot/dts/at91sam9g15ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9g15.dtsi" -/include/ "at91sam9x5ek.dtsi" +#include "at91sam9g15.dtsi" +#include "at91sam9x5ek.dtsi" / { model = "Atmel AT91SAM9G15-EK";
arch/arm/boot/dts/at91sam9g20.dtsi +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ -/include/ "at91sam9260.dtsi" +#include "at91sam9260.dtsi" / { model = "Atmel AT91SAM9G20 family SoC";
arch/arm/boot/dts/at91sam9g20ek.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ /dts-v1/; -/include/ "at91sam9g20ek_common.dtsi" +#include "at91sam9g20ek_common.dtsi" / { model = "Atmel at91sam9g20ek";
arch/arm/boot/dts/at91sam9g20ek_2mmc.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ /dts-v1/; -/include/ "at91sam9g20ek_common.dtsi" +#include "at91sam9g20ek_common.dtsi" / { model = "Atmel at91sam9g20ek 2 mmc";
arch/arm/boot/dts/at91sam9g20ek_common.dtsi +1 -1
@@ -5,7 +5,7 @@ * * Licensed under GPLv2. */ -/include/ "at91sam9g20.dtsi" +#include "at91sam9g20.dtsi" / {
arch/arm/boot/dts/at91sam9g25.dtsi +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ -/include/ "at91sam9x5.dtsi" +#include "at91sam9x5.dtsi" / { model = "Atmel AT91SAM9G25 SoC";
arch/arm/boot/dts/at91sam9g25ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9g25.dtsi" -/include/ "at91sam9x5ek.dtsi" +#include "at91sam9g25.dtsi" +#include "at91sam9x5ek.dtsi" / { model = "Atmel AT91SAM9G25-EK";
arch/arm/boot/dts/at91sam9g35.dtsi +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ -/include/ "at91sam9x5.dtsi" +#include "at91sam9x5.dtsi" / { model = "Atmel AT91SAM9G35 SoC";
arch/arm/boot/dts/at91sam9g35ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9g35.dtsi" -/include/ "at91sam9x5ek.dtsi" +#include "at91sam9g35.dtsi" +#include "at91sam9x5ek.dtsi" / { model = "Atmel AT91SAM9G35-EK";
arch/arm/boot/dts/at91sam9g45.dtsi +1 -1
@@ -9,7 +9,7 @@ * Licensed under GPLv2 or later. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { model = "Atmel AT91SAM9G45 family SoC";
arch/arm/boot/dts/at91sam9m10g45ek.dts +1 -1
@@ -7,7 +7,7 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9g45.dtsi" +#include "at91sam9g45.dtsi" / { model = "Atmel AT91SAM9M10G45-EK";
arch/arm/boot/dts/at91sam9n12.dtsi +1 -1
@@ -7,7 +7,7 @@ * Licensed under GPLv2 or later. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { model = "Atmel AT91SAM9N12 SoC";
arch/arm/boot/dts/at91sam9n12ek.dts +1 -1
@@ -7,7 +7,7 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9n12.dtsi" +#include "at91sam9n12.dtsi" / { model = "Atmel AT91SAM9N12-EK";
arch/arm/boot/dts/at91sam9x25.dtsi +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ -/include/ "at91sam9x5.dtsi" +#include "at91sam9x5.dtsi" / { model = "Atmel AT91SAM9X25 SoC";
arch/arm/boot/dts/at91sam9x25ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9x25.dtsi" -/include/ "at91sam9x5ek.dtsi" +#include "at91sam9x25.dtsi" +#include "at91sam9x5ek.dtsi" / { model = "Atmel AT91SAM9G25-EK";
arch/arm/boot/dts/at91sam9x35.dtsi +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ -/include/ "at91sam9x5.dtsi" +#include "at91sam9x5.dtsi" / { model = "Atmel AT91SAM9X35 SoC";
arch/arm/boot/dts/at91sam9x35ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9x35.dtsi" -/include/ "at91sam9x5ek.dtsi" +#include "at91sam9x35.dtsi" +#include "at91sam9x5ek.dtsi" / { model = "Atmel AT91SAM9X35-EK";
arch/arm/boot/dts/at91sam9x5.dtsi +1 -1
@@ -9,7 +9,7 @@ * Licensed under GPLv2 or later. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { model = "Atmel AT91SAM9x5 family SoC";
arch/arm/boot/dts/at91sam9x5ek.dtsi +1 -1
@@ -6,7 +6,7 @@ * * Licensed under GPLv2 or later. */ -/include/ "at91sam9x5cm.dtsi" +#include "at91sam9x5cm.dtsi" / { model = "Atmel AT91SAM9X5-EK";
arch/arm/boot/dts/ethernut5.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ /dts-v1/; -/include/ "at91sam9260.dtsi" +#include "at91sam9260.dtsi" / { model = "Ethernut 5";
arch/arm/boot/dts/evk-pro3.dts +2 -2
@@ -9,7 +9,7 @@ /dts-v1/; -/include/ "ge863-pro3.dtsi" +#include "ge863-pro3.dtsi" / { model = "Telit EVK-PRO3 for Telit GE863-PRO3";
@@ -50,4 +50,4 @@ status = "okay"; }; -}; +};
arch/arm/boot/dts/ge863-pro3.dtsi +1 -1
@@ -7,7 +7,7 @@ * Licensed under GPLv2 or later. */ -/include/ "at91sam9260.dtsi" +#include "at91sam9260.dtsi" / { clocks {
arch/arm/boot/dts/kizbox.dts +2 -2
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ /dts-v1/; -/include/ "at91sam9g20.dtsi" +#include "at91sam9g20.dtsi" / {
@@ -137,4 +137,4 @@ gpio-key,wakeup; }; }; -}; +};
arch/arm/boot/dts/mpa1600.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2 only */ /dts-v1/; -/include/ "at91rm9200.dtsi" +#include "at91rm9200.dtsi" / { model = "Phontech MPA 1600";
arch/arm/boot/dts/pm9g45.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2. */ /dts-v1/; -/include/ "at91sam9g45.dtsi" +#include "at91sam9g45.dtsi" / { model = "Ronetix pm9g45";
arch/arm/boot/dts/sama5d3.dtsi +1 -1
@@ -8,7 +8,7 @@ * Licensed under GPLv2 or later. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { model = "Atmel SAMA5D3 family SoC";
arch/arm/boot/dts/sama5d31ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "sama5d3xmb.dtsi" -/include/ "sama5d3xdm.dtsi" +#include "sama5d3xmb.dtsi" +#include "sama5d3xdm.dtsi" / { model = "Atmel SAMA5D31-EK";
arch/arm/boot/dts/sama5d33ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "sama5d3xmb.dtsi" -/include/ "sama5d3xdm.dtsi" +#include "sama5d3xmb.dtsi" +#include "sama5d3xdm.dtsi" / { model = "Atmel SAMA5D33-EK";
arch/arm/boot/dts/sama5d34ek.dts +2 -2
@@ -7,8 +7,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "sama5d3xmb.dtsi" -/include/ "sama5d3xdm.dtsi" +#include "sama5d3xmb.dtsi" +#include "sama5d3xdm.dtsi" / { model = "Atmel SAMA5D34-EK";
arch/arm/boot/dts/sama5d35ek.dts +1 -1
@@ -7,7 +7,7 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "sama5d3xmb.dtsi" +#include "sama5d3xmb.dtsi" / { model = "Atmel SAMA5D35-EK";
arch/arm/boot/dts/sama5d3xcm.dtsi +1 -1
@@ -6,7 +6,7 @@ * * Licensed under GPLv2 or later. */ -/include/ "sama5d3.dtsi" +#include "sama5d3.dtsi" / { compatible = "atmel,samad3xcm", "atmel,sama5d3", "atmel,sama5";
arch/arm/boot/dts/sama5d3xmb.dtsi +1 -1
@@ -6,7 +6,7 @@ * * Licensed under GPLv2 or later. */ -/include/ "sama5d3xcm.dtsi" +#include "sama5d3xcm.dtsi" / { compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
arch/arm/boot/dts/tny_a9260.dts +2 -2
@@ -6,8 +6,8 @@ * Licensed under GPLv2. */ /dts-v1/; -/include/ "at91sam9260.dtsi" -/include/ "tny_a9260_common.dtsi" +#include "at91sam9260.dtsi" +#include "tny_a9260_common.dtsi" / { model = "Calao TNY A9260";
arch/arm/boot/dts/tny_a9263.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2 only */ /dts-v1/; -/include/ "at91sam9263.dtsi" +#include "at91sam9263.dtsi" / { model = "Calao TNY A9263";
arch/arm/boot/dts/tny_a9g20.dts +2 -2
@@ -6,8 +6,8 @@ * Licensed under GPLv2. */ /dts-v1/; -/include/ "at91sam9g20.dtsi" -/include/ "tny_a9260_common.dtsi" +#include "at91sam9g20.dtsi" +#include "tny_a9260_common.dtsi" / { model = "Calao TNY A9G20";
arch/arm/boot/dts/usb_a9260.dts +2 -2
@@ -6,8 +6,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9260.dtsi" -/include/ "usb_a9260_common.dtsi" +#include "at91sam9260.dtsi" +#include "usb_a9260_common.dtsi" / { model = "Calao USB A9260";
arch/arm/boot/dts/usb_a9263.dts +1 -1
@@ -6,7 +6,7 @@ * Licensed under GPLv2 only */ /dts-v1/; -/include/ "at91sam9263.dtsi" +#include "at91sam9263.dtsi" / { model = "Calao USB A9263";
arch/arm/boot/dts/usb_a9g20.dts +2 -2
@@ -6,8 +6,8 @@ * Licensed under GPLv2 or later. */ /dts-v1/; -/include/ "at91sam9g20.dtsi" -/include/ "usb_a9260_common.dtsi" +#include "at91sam9g20.dtsi" +#include "usb_a9260_common.dtsi" / { model = "Calao USB A9G20";
Signature · 7 lines
1.7.10.4 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH 2/5 ARM: at91: dt: switch to standard GPIO flag defines.
--- arch/arm/boot/dts/aks-cdu.dts | 10 ++++----- arch/arm/boot/dts/animeo_ip.dts | 16 +++++++------- arch/arm/boot/dts/at91-ariag25.dts | 4 ++-- arch/arm/boot/dts/at91rm9200.dtsi | 9 ++++---- arch/arm/boot/dts/at91rm9200ek.dts | 8 +++---- arch/arm/boot/dts/at91sam9260.dtsi | 9 ++++---- arch/arm/boot/dts/at91sam9263.dtsi | 9 ++++---- arch/arm/boot/dts/at91sam9263ek.dts | 18 ++++++++-------- arch/arm/boot/dts/at91sam9g20ek.dts | 4 ++-- arch/arm/boot/dts/at91sam9g20ek_2mmc.dts | 6 +++--- arch/arm/boot/dts/at91sam9g20ek_common.dtsi | 8 +++---- arch/arm/boot/dts/at91sam9g45.dtsi | 9 ++++---- arch/arm/boot/dts/at91sam9m10g45ek.dts | 30 +++++++++++++-------------- arch/arm/boot/dts/at91sam9n12.dtsi | 9 ++++---- arch/arm/boot/dts/at91sam9n12ek.dts | 10 ++++----- arch/arm/boot/dts/at91sam9x5.dtsi | 17 ++++++++------- arch/arm/boot/dts/at91sam9x5cm.dtsi | 6 +++--- arch/arm/boot/dts/at91sam9x5ek.dtsi | 8 +++---- arch/arm/boot/dts/ethernut5.dts | 4 ++-- arch/arm/boot/dts/evk-pro3.dts | 2 +- arch/arm/boot/dts/kizbox.dts | 12 +++++------ arch/arm/boot/dts/mpa1600.dts | 2 +- arch/arm/boot/dts/pm9g45.dts | 14 ++++++------- arch/arm/boot/dts/sama5d3.dtsi | 1 + arch/arm/boot/dts/sama5d31ek.dts | 2 +- arch/arm/boot/dts/sama5d34ek.dts | 2 +- arch/arm/boot/dts/sama5d35ek.dts | 2 +- arch/arm/boot/dts/sama5d3xcm.dtsi | 2 +- arch/arm/boot/dts/sama5d3xmb.dtsi | 12 +++++------ arch/arm/boot/dts/tny_a9263.dts | 2 +- arch/arm/boot/dts/usb_a9260_common.dtsi | 6 +++--- arch/arm/boot/dts/usb_a9263.dts | 6 +++--- arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi | 22 ++++++++++---------- 33 files changed, 144 insertions(+), 137 deletions(-)
arch/arm/boot/dts/aks-cdu.dts +5 -5
@@ -46,7 +46,7 @@ }; usb1: gadget@fffa4000 { - atmel,vbus-gpio = <&pioC 15 0>; + atmel,vbus-gpio = <&pioC 15 GPIO_ACTIVE_HIGH>; status = "okay"; }; };
@@ -90,23 +90,23 @@ compatible = "gpio-leds"; red { - gpios = <&pioC 10 0>; + gpios = <&pioC 10 GPIO_ACTIVE_HIGH>; linux,default-trigger = "none"; }; green { - gpios = <&pioA 5 1>; + gpios = <&pioA 5 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; default-state = "on"; }; yellow { - gpios = <&pioB 20 1>; + gpios = <&pioB 20 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; blue { - gpios = <&pioB 21 1>; + gpios = <&pioB 21 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; };
arch/arm/boot/dts/animeo_ip.dts +8 -8
@@ -123,7 +123,7 @@ usb0: ohci@00500000 { num-ports = <2>; - atmel,vbus-gpio = <&pioB 15 1>; + atmel,vbus-gpio = <&pioB 15 GPIO_ACTIVE_LOW>; status = "okay"; }; };
@@ -133,23 +133,23 @@ power_green { label = "power_green"; - gpios = <&pioC 17 0>; + gpios = <&pioC 17 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; power_red { label = "power_red"; - gpios = <&pioA 2 0>; + gpios = <&pioA 2 GPIO_ACTIVE_HIGH>; }; tx_green { label = "tx_green"; - gpios = <&pioC 19 0>; + gpios = <&pioC 19 GPIO_ACTIVE_HIGH>; }; tx_red { label = "tx_red"; - gpios = <&pioC 18 0>; + gpios = <&pioC 18 GPIO_ACTIVE_HIGH>; }; };
@@ -160,21 +160,21 @@ keyswitch_in { label = "keyswitch_in"; - gpios = <&pioB 1 0>; + gpios = <&pioB 1 GPIO_ACTIVE_HIGH>; linux,code = <28>; gpio-key,wakeup; }; error_in { label = "error_in"; - gpios = <&pioB 2 0>; + gpios = <&pioB 2 GPIO_ACTIVE_HIGH>; linux,code = <29>; gpio-key,wakeup; }; btn { label = "btn"; - gpios = <&pioC 23 0>; + gpios = <&pioC 23 GPIO_ACTIVE_HIGH>; linux,code = <31>; gpio-key,wakeup; };
arch/arm/boot/dts/at91-ariag25.dts +2 -2
@@ -156,7 +156,7 @@ /* little green LED in middle of Aria G25 module */ aria_led { label = "aria_led"; - gpios = <&pioB 8 0>; /* PB8 */ + gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */ linux,default-trigger = "heartbeat"; };
@@ -164,7 +164,7 @@ onewire@0 { compatible = "w1-gpio"; - gpios = <&pioA 21 1>; + gpios = <&pioA 21 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_w1_0>; };
arch/arm/boot/dts/at91rm9200.dtsi +5 -4
@@ -11,6 +11,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel AT91RM9200 family SoC";
@@ -503,9 +504,9 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; nand-ecc-mode = "soft"; - gpios = <&pioC 2 0 + gpios = <&pioC 2 GPIO_ACTIVE_HIGH 0 - &pioB 1 0 + &pioB 1 GPIO_ACTIVE_HIGH >; status = "disabled"; };
@@ -520,8 +521,8 @@ i2c@0 { compatible = "i2c-gpio"; - gpios = <&pioA 25 0 /* sda */ - &pioA 26 0 /* scl */ + gpios = <&pioA 25 GPIO_ACTIVE_HIGH /* sda */ + &pioA 26 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
arch/arm/boot/dts/at91rm9200ek.dts +4 -4
@@ -50,7 +50,7 @@ }; usb1: gadget@fffb0000 { - atmel,vbus-gpio = <&pioD 4 0>; + atmel,vbus-gpio = <&pioD 4 GPIO_ACTIVE_HIGH>; status = "okay"; }; };
@@ -66,19 +66,19 @@ ds2 { label = "green"; - gpios = <&pioB 0 0x1>; + gpios = <&pioB 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "mmc0"; }; ds4 { label = "yellow"; - gpios = <&pioB 1 0x1>; + gpios = <&pioB 1 GPIO_ACTIVE_LOW>; linux,default-trigger = "heartbeat"; }; ds6 { label = "red"; - gpios = <&pioB 2 0x1>; + gpios = <&pioB 2 GPIO_ACTIVE_LOW>; }; }; };
arch/arm/boot/dts/at91sam9260.dtsi +5 -4
@@ -9,6 +9,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel AT91SAM9260 family SoC";
@@ -567,8 +568,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioC 13 0 - &pioC 14 0 + gpios = <&pioC 13 GPIO_ACTIVE_HIGH + &pioC 14 GPIO_ACTIVE_HIGH 0 >; status = "disabled";
@@ -584,8 +585,8 @@ i2c@0 { compatible = "i2c-gpio"; - gpios = <&pioA 23 0 /* sda */ - &pioA 24 0 /* scl */ + gpios = <&pioA 23 GPIO_ACTIVE_HIGH /* sda */ + &pioA 24 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
arch/arm/boot/dts/at91sam9263.dtsi +5 -4
@@ -7,6 +7,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel AT91SAM9263 family SoC";
@@ -515,8 +516,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioA 22 0 - &pioD 15 0 + gpios = <&pioA 22 GPIO_ACTIVE_HIGH + &pioD 15 GPIO_ACTIVE_HIGH 0 >; status = "disabled";
@@ -532,8 +533,8 @@ i2c@0 { compatible = "i2c-gpio"; - gpios = <&pioB 4 0 /* sda */ - &pioB 5 0 /* scl */ + gpios = <&pioB 4 GPIO_ACTIVE_HIGH /* sda */ + &pioB 5 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
arch/arm/boot/dts/at91sam9263ek.dts +9 -9
@@ -51,7 +51,7 @@ }; usb1: gadget@fff78000 { - atmel,vbus-gpio = <&pioA 25 0>; + atmel,vbus-gpio = <&pioA 25 GPIO_ACTIVE_HIGH>; status = "okay"; };
@@ -65,8 +65,8 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioE 18 0>; - wp-gpios = <&pioE 19 0>; + cd-gpios = <&pioE 18 GPIO_ACTIVE_HIGH>; + wp-gpios = <&pioE 19 GPIO_ACTIVE_HIGH>; }; };
@@ -141,8 +141,8 @@ usb0: ohci@00a00000 { num-ports = <2>; status = "okay"; - atmel,vbus-gpio = <&pioA 24 0 - &pioA 21 0 + atmel,vbus-gpio = <&pioA 24 GPIO_ACTIVE_HIGH + &pioA 21 GPIO_ACTIVE_HIGH >; }; };
@@ -152,13 +152,13 @@ d3 { label = "d3"; - gpios = <&pioB 7 0>; + gpios = <&pioB 7 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; d2 { label = "d2"; - gpios = <&pioC 29 1>; + gpios = <&pioC 29 GPIO_ACTIVE_LOW>; linux,default-trigger = "nand-disk"; }; };
@@ -168,14 +168,14 @@ left_click { label = "left_click"; - gpios = <&pioC 5 1>; + gpios = <&pioC 5 GPIO_ACTIVE_LOW>; linux,code = <272>; gpio-key,wakeup; }; right_click { label = "right_click"; - gpios = <&pioC 4 1>; + gpios = <&pioC 4 GPIO_ACTIVE_LOW>; linux,code = <273>; gpio-key,wakeup; };
arch/arm/boot/dts/at91sam9g20ek.dts +2 -2
@@ -17,13 +17,13 @@ ds1 { label = "ds1"; - gpios = <&pioA 9 0>; + gpios = <&pioA 9 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; ds5 { label = "ds5"; - gpios = <&pioA 6 1>; + gpios = <&pioA 6 GPIO_ACTIVE_LOW>; }; }; };
arch/arm/boot/dts/at91sam9g20ek_2mmc.dts +3 -3
@@ -23,7 +23,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioC 2 0>; + cd-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; }; };
@@ -43,13 +43,13 @@ ds1 { label = "ds1"; - gpios = <&pioB 9 0>; + gpios = <&pioB 9 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; ds5 { label = "ds5"; - gpios = <&pioB 8 1>; + gpios = <&pioB 8 GPIO_ACTIVE_LOW>; }; }; };
arch/arm/boot/dts/at91sam9g20ek_common.dtsi +4 -4
@@ -65,7 +65,7 @@ }; usb1: gadget@fffa4000 { - atmel,vbus-gpio = <&pioC 5 0>; + atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>; status = "okay"; };
@@ -79,7 +79,7 @@ slot@1 { reg = <1>; bus-width = <4>; - cd-gpios = <&pioC 9 0>; + cd-gpios = <&pioC 9 GPIO_ACTIVE_HIGH>; }; };
@@ -180,14 +180,14 @@ btn3 { label = "Button 3"; - gpios = <&pioA 30 1>; + gpios = <&pioA 30 GPIO_ACTIVE_LOW>; linux,code = <0x103>; gpio-key,wakeup; }; btn4 { label = "Button 4"; - gpios = <&pioA 31 1>; + gpios = <&pioA 31 GPIO_ACTIVE_LOW>; linux,code = <0x104>; gpio-key,wakeup; };
arch/arm/boot/dts/at91sam9g45.dtsi +5 -4
@@ -10,6 +10,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel AT91SAM9G45 family SoC";
@@ -592,8 +593,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioC 8 0 - &pioC 14 0 + gpios = <&pioC 8 GPIO_ACTIVE_HIGH + &pioC 14 GPIO_ACTIVE_HIGH 0 >; status = "disabled";
@@ -616,8 +617,8 @@ i2c@0 { compatible = "i2c-gpio"; - gpios = <&pioA 20 0 /* sda */ - &pioA 21 0 /* scl */ + gpios = <&pioA 20 GPIO_ACTIVE_HIGH /* sda */ + &pioA 21 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
arch/arm/boot/dts/at91sam9m10g45ek.dts +15 -15
@@ -68,7 +68,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 10 0>; + cd-gpios = <&pioD 10 GPIO_ACTIVE_HIGH>; }; };
@@ -81,8 +81,8 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 11 0>; - wp-gpios = <&pioD 29 0>; + cd-gpios = <&pioD 11 GPIO_ACTIVE_HIGH>; + wp-gpios = <&pioD 29 GPIO_ACTIVE_HIGH>; }; };
@@ -139,8 +139,8 @@ usb0: ohci@00700000 { status = "okay"; num-ports = <2>; - atmel,vbus-gpio = <&pioD 1 1 - &pioD 3 1>; + atmel,vbus-gpio = <&pioD 1 GPIO_ACTIVE_LOW + &pioD 3 GPIO_ACTIVE_LOW>; }; usb1: ehci@00800000 {
@@ -153,19 +153,19 @@ d8 { label = "d8"; - gpios = <&pioD 30 0>; + gpios = <&pioD 30 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; d6 { label = "d6"; - gpios = <&pioD 0 1>; + gpios = <&pioD 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "nand-disk"; }; d7 { label = "d7"; - gpios = <&pioD 31 1>; + gpios = <&pioD 31 GPIO_ACTIVE_LOW>; linux,default-trigger = "mmc0"; }; };
@@ -175,45 +175,45 @@ left_click { label = "left_click"; - gpios = <&pioB 6 1>; + gpios = <&pioB 6 GPIO_ACTIVE_LOW>; linux,code = <272>; gpio-key,wakeup; }; right_click { label = "right_click"; - gpios = <&pioB 7 1>; + gpios = <&pioB 7 GPIO_ACTIVE_LOW>; linux,code = <273>; gpio-key,wakeup; }; left { label = "Joystick Left"; - gpios = <&pioB 14 1>; + gpios = <&pioB 14 GPIO_ACTIVE_LOW>; linux,code = <105>; }; right { label = "Joystick Right"; - gpios = <&pioB 15 1>; + gpios = <&pioB 15 GPIO_ACTIVE_LOW>; linux,code = <106>; }; up { label = "Joystick Up"; - gpios = <&pioB 16 1>; + gpios = <&pioB 16 GPIO_ACTIVE_LOW>; linux,code = <103>; }; down { label = "Joystick Down"; - gpios = <&pioB 17 1>; + gpios = <&pioB 17 GPIO_ACTIVE_LOW>; linux,code = <108>; }; enter { label = "Joystick Press"; - gpios = <&pioB 18 1>; + gpios = <&pioB 18 GPIO_ACTIVE_LOW>; linux,code = <28>; }; };
arch/arm/boot/dts/at91sam9n12.dtsi +5 -4
@@ -8,6 +8,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel AT91SAM9N12 SoC";
@@ -438,8 +439,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioD 5 0 - &pioD 4 0 + gpios = <&pioD 5 GPIO_ACTIVE_HIGH + &pioD 4 GPIO_ACTIVE_HIGH 0 >; status = "disabled";
@@ -455,8 +456,8 @@ i2c@0 { compatible = "i2c-gpio"; - gpios = <&pioA 30 0 /* sda */ - &pioA 31 0 /* scl */ + gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */ + &pioA 31 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
arch/arm/boot/dts/at91sam9n12ek.dts +5 -5
@@ -55,7 +55,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioA 7 0>; + cd-gpios = <&pioA 7 GPIO_ACTIVE_HIGH>; }; };
@@ -95,19 +95,19 @@ d8 { label = "d8"; - gpios = <&pioB 4 1>; + gpios = <&pioB 4 GPIO_ACTIVE_LOW>; linux,default-trigger = "mmc0"; }; d9 { label = "d6"; - gpios = <&pioB 5 1>; + gpios = <&pioB 5 GPIO_ACTIVE_LOW>; linux,default-trigger = "nand-disk"; }; d10 { label = "d7"; - gpios = <&pioB 6 0>; + gpios = <&pioB 6 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; };
@@ -117,7 +117,7 @@ enter { label = "Enter"; - gpios = <&pioB 4 1>; + gpios = <&pioB 4 GPIO_ACTIVE_LOW>; linux,code = <28>; gpio-key,wakeup; };
arch/arm/boot/dts/at91sam9x5.dtsi +9 -8
@@ -10,6 +10,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel AT91SAM9x5 family SoC";
@@ -664,8 +665,8 @@ atmel,nand-cmd-offset = <22>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; - gpios = <&pioD 5 0 - &pioD 4 0 + gpios = <&pioD 5 GPIO_ACTIVE_HIGH + &pioD 4 GPIO_ACTIVE_HIGH 0 >; status = "disabled";
@@ -688,8 +689,8 @@ i2c@0 { compatible = "i2c-gpio"; - gpios = <&pioA 30 0 /* sda */ - &pioA 31 0 /* scl */ + gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */ + &pioA 31 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
@@ -703,8 +704,8 @@ i2c@1 { compatible = "i2c-gpio"; - gpios = <&pioC 0 0 /* sda */ - &pioC 1 0 /* scl */ + gpios = <&pioC 0 GPIO_ACTIVE_HIGH /* sda */ + &pioC 1 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
@@ -718,8 +719,8 @@ i2c@2 { compatible = "i2c-gpio"; - gpios = <&pioB 4 0 /* sda */ - &pioB 5 0 /* scl */ + gpios = <&pioB 4 GPIO_ACTIVE_HIGH /* sda */ + &pioB 5 GPIO_ACTIVE_HIGH /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain;
arch/arm/boot/dts/at91sam9x5cm.dtsi +3 -3
@@ -75,19 +75,19 @@ pb18 { label = "pb18"; - gpios = <&pioB 18 1>; + gpios = <&pioB 18 GPIO_ACTIVE_LOW>; linux,default-trigger = "heartbeat"; }; pd21 { label = "pd21"; - gpios = <&pioD 21 0>; + gpios = <&pioD 21 GPIO_ACTIVE_HIGH>; }; }; 1wire_cm { compatible = "w1-gpio"; - gpios = <&pioB 18 0>; + gpios = <&pioB 18 GPIO_ACTIVE_HIGH>; linux,open-drain; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_1wire_cm>;
arch/arm/boot/dts/at91sam9x5ek.dtsi +4 -4
@@ -27,7 +27,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 15 0>; + cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>; }; };
@@ -40,7 +40,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 14 0>; + cd-gpios = <&pioD 14 GPIO_ACTIVE_HIGH>; }; };
@@ -86,8 +86,8 @@ usb0: ohci@00600000 { status = "okay"; num-ports = <2>; - atmel,vbus-gpio = <&pioD 19 1 - &pioD 20 1 + atmel,vbus-gpio = <&pioD 19 GPIO_ACTIVE_LOW + &pioD 20 GPIO_ACTIVE_LOW >; };
arch/arm/boot/dts/ethernut5.dts +2 -2
@@ -40,7 +40,7 @@ }; usb1: gadget@fffa4000 { - atmel,vbus-gpio = <&pioC 5 0>; + atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>; status = "okay"; }; };
@@ -52,7 +52,7 @@ status = "okay"; gpios = <0 - &pioC 14 0 + &pioC 14 GPIO_ACTIVE_HIGH 0 >;
arch/arm/boot/dts/evk-pro3.dts +1 -1
@@ -31,7 +31,7 @@ }; usb1: gadget@fffa4000 { - atmel,vbus-gpio = <&pioC 5 0>; + atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>; status = "okay"; };
arch/arm/boot/dts/kizbox.dts +6 -6
@@ -94,26 +94,26 @@ led1g { label = "led1:green"; - gpios = <&pioB 0 1>; + gpios = <&pioB 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; led1r { label = "led1:red"; - gpios = <&pioB 1 1>; + gpios = <&pioB 1 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; led2g { label = "led2:green"; - gpios = <&pioB 2 1>; + gpios = <&pioB 2 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; default-state = "on"; }; led2r { label = "led2:red"; - gpios = <&pioB 3 1>; + gpios = <&pioB 3 GPIO_ACTIVE_LOW>; linux,default-trigger = "none"; }; };
@@ -125,14 +125,14 @@ reset { label = "reset"; - gpios = <&pioB 30 1>; + gpios = <&pioB 30 GPIO_ACTIVE_LOW>; linux,code = <0x100>; gpio-key,wakeup; }; mode { label = "mode"; - gpios = <&pioB 31 1>; + gpios = <&pioB 31 GPIO_ACTIVE_LOW>; linux,code = <0x101>; gpio-key,wakeup; };
arch/arm/boot/dts/mpa1600.dts +1 -1
@@ -62,7 +62,7 @@ monitor_mute { label = "Monitor mute"; - gpios = <&pioC 1 1>; + gpios = <&pioC 1 GPIO_ACTIVE_LOW>; linux,code = <113>; }; };
arch/arm/boot/dts/pm9g45.dts +7 -7
@@ -64,7 +64,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 6 0>; + cd-gpios = <&pioD 6 GPIO_ACTIVE_HIGH>; }; };
@@ -81,8 +81,8 @@ nand-on-flash-bbt; pinctrl-0 = <&pinctrl_board_nand>; - gpios = <&pioD 3 0 - &pioC 14 0 + gpios = <&pioD 3 GPIO_ACTIVE_HIGH + &pioC 14 GPIO_ACTIVE_HIGH 0 >;
@@ -134,13 +134,13 @@ led0 { label = "led0"; - gpios = <&pioD 0 1>; + gpios = <&pioD 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "nand-disk"; }; led1 { label = "led1"; - gpios = <&pioD 31 0>; + gpios = <&pioD 31 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; };
@@ -152,13 +152,13 @@ right { label = "SW4"; - gpios = <&pioE 7 1>; + gpios = <&pioE 7 GPIO_ACTIVE_LOW>; linux,code = <106>; }; up { label = "SW3"; - gpios = <&pioE 8 1>; + gpios = <&pioE 8 GPIO_ACTIVE_LOW>; linux,code = <103>; }; };
arch/arm/boot/dts/sama5d3.dtsi +1 -0
@@ -9,6 +9,7 @@ */ #include "skeleton.dtsi" +#include <dt-bindings/gpio/gpio.h> / { model = "Atmel SAMA5D3 family SoC";
arch/arm/boot/dts/sama5d31ek.dts +1 -1
@@ -41,7 +41,7 @@ leds { d3 { label = "d3"; - gpios = <&pioE 24 0>; + gpios = <&pioE 24 GPIO_ACTIVE_HIGH>; }; };
arch/arm/boot/dts/sama5d34ek.dts +1 -1
@@ -51,7 +51,7 @@ leds { d3 { label = "d3"; - gpios = <&pioE 24 0>; + gpios = <&pioE 24 GPIO_ACTIVE_HIGH>; }; };
arch/arm/boot/dts/sama5d35ek.dts +1 -1
@@ -48,7 +48,7 @@ pb_user1 { label = "pb_user1"; - gpios = <&pioE 27 0>; + gpios = <&pioE 27 GPIO_ACTIVE_HIGH>; linux,code = <0x100>; gpio-key,wakeup; };
arch/arm/boot/dts/sama5d3xcm.dtsi +1 -1
@@ -85,7 +85,7 @@ d2 { label = "d2"; - gpios = <&pioE 25 1>; /* PE25, conflicts with A25, RXD2 */ + gpios = <&pioE 25 GPIO_ACTIVE_LOW>; /* PE25, conflicts with A25, RXD2 */ }; }; };
arch/arm/boot/dts/sama5d3xmb.dtsi +6 -6
@@ -20,7 +20,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 17 0>; + cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>; }; };
@@ -62,7 +62,7 @@ slot@0 { reg = <0>; bus-width = <4>; - cd-gpios = <&pioD 18 0>; + cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>; }; };
@@ -127,7 +127,7 @@ }; usb0: gadget@00500000 { - atmel,vbus-gpio = <&pioD 29 0>; + atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_usba_vbus>; status = "okay";
@@ -135,9 +135,9 @@ usb1: ohci@00600000 { num-ports = <3>; - atmel,vbus-gpio = <&pioD 25 0 - &pioD 26 1 - &pioD 27 1 + atmel,vbus-gpio = <&pioD 25 GPIO_ACTIVE_HIGH + &pioD 26 GPIO_ACTIVE_LOW + &pioD 27 GPIO_ACTIVE_LOW >; status = "okay"; };
arch/arm/boot/dts/tny_a9263.dts +1 -1
@@ -38,7 +38,7 @@ }; usb1: gadget@fff78000 { - atmel,vbus-gpio = <&pioB 11 0>; + atmel,vbus-gpio = <&pioB 11 GPIO_ACTIVE_HIGH>; status = "okay"; }; };
arch/arm/boot/dts/usb_a9260_common.dtsi +3 -3
@@ -30,7 +30,7 @@ }; usb1: gadget@fffa4000 { - atmel,vbus-gpio = <&pioC 5 0>; + atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>; status = "okay"; }; };
@@ -93,7 +93,7 @@ user_led { label = "user_led"; - gpios = <&pioB 21 1>; + gpios = <&pioB 21 GPIO_ACTIVE_LOW>; linux,default-trigger = "heartbeat"; }; };
@@ -105,7 +105,7 @@ user_pb { label = "user_pb"; - gpios = <&pioB 10 1>; + gpios = <&pioB 10 GPIO_ACTIVE_LOW>; linux,code = <28>; gpio-key,wakeup; };
arch/arm/boot/dts/usb_a9263.dts +3 -3
@@ -43,7 +43,7 @@ }; usb1: gadget@fff78000 { - atmel,vbus-gpio = <&pioB 11 0>; + atmel,vbus-gpio = <&pioB 11 GPIO_ACTIVE_HIGH>; status = "okay"; };
@@ -107,7 +107,7 @@ user_led { label = "user_led"; - gpios = <&pioB 21 0>; + gpios = <&pioB 21 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; };
@@ -119,7 +119,7 @@ user_pb { label = "user_pb"; - gpios = <&pioB 10 1>; + gpios = <&pioB 10 GPIO_ACTIVE_LOW>; linux,code = <28>; gpio-key,wakeup; };
arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi +11 -11
@@ -28,39 +28,39 @@ user_led1 { label = "user_led1"; - gpios = <&pioB 20 1>; + gpios = <&pioB 20 GPIO_ACTIVE_LOW>; }; /* * led already used by mother board but active as high * user_led2 { * label = "user_led2"; -* gpios = <&pioB 21 1>; +* gpios = <&pioB 21 GPIO_ACTIVE_LOW>; * }; */ user_led3 { label = "user_led3"; - gpios = <&pioB 22 1>; + gpios = <&pioB 22 GPIO_ACTIVE_LOW>; }; user_led4 { label = "user_led4"; - gpios = <&pioB 23 1>; + gpios = <&pioB 23 GPIO_ACTIVE_LOW>; }; red { label = "red"; - gpios = <&pioB 24 1>; + gpios = <&pioB 24 GPIO_ACTIVE_LOW>; }; orange { label = "orange"; - gpios = <&pioB 30 1>; + gpios = <&pioB 30 GPIO_ACTIVE_LOW>; }; green { label = "green"; - gpios = <&pioB 31 1>; + gpios = <&pioB 31 GPIO_ACTIVE_LOW>; }; };
@@ -71,25 +71,25 @@ user_pb1 { label = "user_pb1"; - gpios = <&pioB 25 1>; + gpios = <&pioB 25 GPIO_ACTIVE_LOW>; linux,code = <0x100>; }; user_pb2 { label = "user_pb2"; - gpios = <&pioB 13 1>; + gpios = <&pioB 13 GPIO_ACTIVE_LOW>; linux,code = <0x101>; }; user_pb3 { label = "user_pb3"; - gpios = <&pioA 26 1>; + gpios = <&pioA 26 GPIO_ACTIVE_LOW>; linux,code = <0x102>; }; user_pb4 { label = "user_pb4"; - gpios = <&pioC 9 1>; + gpios = <&pioC 9 GPIO_ACTIVE_LOW>; linux,code = <0x103>; }; };
Signature · 7 lines
1.7.10.4 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH 3/5 ARM: at91: dt: add pinctrl pre-processor define
In reply to Jean-Christophe PLAGNIOL-VILLARD--- include/dt-bindings/pinctrl/at91.h | 35 +++++++++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+) create mode 100644 include/dt-bindings/pinctrl/at91.h
include/dt-bindings/pinctrl/at91.h new file +35 -0
@@ -0,0 +1,35 @@ +/* +* This header provides constants for most at91 pinctrl bindings. +* +* Copyright (C) 2013 Jean-Christophe PLAGNIOL-VILLARD <[email protected]> +* +* GPLv2 only +*/ + +#ifndef __DT_BINDINGS_AT91_PINCTRL_H__ +#define __DT_BINDINGS_AT91_PINCTRL_H__ + +#define AT91_PINCTRL_NONE (0 << 0) +#define AT91_PINCTRL_PULL_UP (1 << 0) +#define AT91_PINCTRL_MULTI_DRIVE (1 << 1) +#define AT91_PINCTRL_DEGLITCH (1 << 2) +#define AT91_PINCTRL_PULL_DOWN (1 << 3) +#define AT91_PINCTRL_DIS_SCHMIT (1 << 4) +#define AT91_PINCTRL_DEBOUNCE (1 << 16) +#define AT91_PINCTRL_DEBOUNCE_VA (x) (x << 17) + +#define AT91_PINCTRL_PULL_UP_DEGLITCH (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DEGLITCH) + +#define AT91_PIOA 0 +#define AT91_PIOB 1 +#define AT91_PIOC 2 +#define AT91_PIOD 3 +#define AT91_PIOE 4 + +#define AT91_PERIPH_GPIO 0 +#define AT91_PERIPH_A 1 +#define AT91_PERIPH_B 2 +#define AT91_PERIPH_C 3 +#define AT91_PERIPH_D 4 + +#endif /* __DT_BINDINGS_AT91_PINCTRL_H__ */
Signature · 7 lines
1.7.10.4 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH 5/5 ARM: at91: dt: switch to standard IRQ flag defines
In reply to Jean-Christophe PLAGNIOL-VILLARD--- arch/arm/boot/dts/at91rm9200.dtsi | 45 +++++++++++--------- arch/arm/boot/dts/at91sam9260.dtsi | 49 ++++++++++++---------- arch/arm/boot/dts/at91sam9263.dtsi | 43 ++++++++++---------- arch/arm/boot/dts/at91sam9g45.dtsi | 49 +++++++++++----------- arch/arm/boot/dts/at91sam9n12.dtsi | 41 ++++++++++--------- arch/arm/boot/dts/at91sam9x5.dtsi | 55 +++++++++++++------------ arch/arm/boot/dts/sama5d3.dtsi | 79 ++++++++++++++++++------------------ 7 files changed, 188 insertions(+), 173 deletions(-)
arch/arm/boot/dts/at91rm9200.dtsi +25 -20
@@ -12,6 +12,7 @@ #include "skeleton.dtsi" #include <dt-bindings/pinctrl/at91.h> +#include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/gpio/gpio.h> / {
@@ -79,25 +80,29 @@ st: timer@fffffd00 { compatible = "atmel,at91rm9200-st"; reg = <0xfffffd00 0x100>; - interrupts = <1 4 7>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; }; tcb0: timer@fffa0000 { compatible = "atmel,at91rm9200-tcb"; reg = <0xfffa0000 0x100>; - interrupts = <17 4 0 18 4 0 19 4 0>; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0 + 18 IRQ_TYPE_LEVEL_HIGH 0 + 19 IRQ_TYPE_LEVEL_HIGH 0>; }; tcb1: timer@fffa4000 { compatible = "atmel,at91rm9200-tcb"; reg = <0xfffa4000 0x100>; - interrupts = <20 4 0 21 4 0 22 4 0>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0 + 21 IRQ_TYPE_LEVEL_HIGH 0 + 22 IRQ_TYPE_LEVEL_HIGH 0>; }; i2c0: i2c@fffb8000 { compatible = "atmel,at91rm9200-i2c"; reg = <0xfffb8000 0x4000>; - interrupts = <12 4 6>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH 6>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_twi>; #address-cells = <1>;
@@ -108,7 +113,7 @@ mmc0: mmc@fffb4000 { compatible = "atmel,hsmci"; reg = <0xfffb4000 0x4000>; - interrupts = <10 4 0>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH 0>; #address-cells = <1>; #size-cells = <0>; status = "disabled";
@@ -117,7 +122,7 @@ ssc0: ssc@fffd0000 { compatible = "atmel,at91rm9200-ssc"; reg = <0xfffd0000 0x4000>; - interrupts = <14 4 5>; + interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; status = "disable";
@@ -126,7 +131,7 @@ ssc1: ssc@fffd4000 { compatible = "atmel,at91rm9200-ssc"; reg = <0xfffd4000 0x4000>; - interrupts = <15 4 5>; + interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; status = "disable";
@@ -135,7 +140,7 @@ ssc2: ssc@fffd8000 { compatible = "atmel,at91rm9200-ssc"; reg = <0xfffd8000 0x4000>; - interrupts = <16 4 5>; + interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc2_tx &pinctrl_ssc2_rx>; status = "disable";
@@ -144,7 +149,7 @@ macb0: ethernet@fffbc000 { compatible = "cdns,at91rm9200-emac", "cdns,emac"; reg = <0xfffbc000 0x4000>; - interrupts = <24 4 3>; + interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3>; phy-mode = "rmii"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_macb_rmii>;
@@ -396,7 +401,7 @@ pioA: gpio@fffff400 { compatible = "atmel,at91rm9200-gpio"; reg = <0xfffff400 0x200>; - interrupts = <2 4 1>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>; #gpio-cells = <2>; gpio-controller; interrupt-controller;
@@ -406,7 +411,7 @@ pioB: gpio@fffff600 { compatible = "atmel,at91rm9200-gpio"; reg = <0xfffff600 0x200>; - interrupts = <3 4 1>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>; #gpio-cells = <2>; gpio-controller; interrupt-controller;
@@ -416,7 +421,7 @@ pioC: gpio@fffff800 { compatible = "atmel,at91rm9200-gpio"; reg = <0xfffff800 0x200>; - interrupts = <4 4 1>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>; #gpio-cells = <2>; gpio-controller; interrupt-controller;
@@ -426,7 +431,7 @@ pioD: gpio@fffffa00 { compatible = "atmel,at91rm9200-gpio"; reg = <0xfffffa00 0x200>; - interrupts = <5 4 1>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH 1>; #gpio-cells = <2>; gpio-controller; interrupt-controller;
@@ -437,7 +442,7 @@ dbgu: serial@fffff200 { compatible = "atmel,at91rm9200-usart"; reg = <0xfffff200 0x200>; - interrupts = <1 4 7>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_dbgu>; status = "disabled";
@@ -446,7 +451,7 @@ usart0: serial@fffc0000 { compatible = "atmel,at91rm9200-usart"; reg = <0xfffc0000 0x200>; - interrupts = <6 4 5>; + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>; atmel,use-dma-rx; atmel,use-dma-tx; pinctrl-names = "default";
@@ -457,7 +462,7 @@ usart1: serial@fffc4000 { compatible = "atmel,at91rm9200-usart"; reg = <0xfffc4000 0x200>; - interrupts = <7 4 5>; + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>; atmel,use-dma-rx; atmel,use-dma-tx; pinctrl-names = "default";
@@ -468,7 +473,7 @@ usart2: serial@fffc8000 { compatible = "atmel,at91rm9200-usart"; reg = <0xfffc8000 0x200>; - interrupts = <8 4 5>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>; atmel,use-dma-rx; atmel,use-dma-tx; pinctrl-names = "default";
@@ -479,7 +484,7 @@ usart3: serial@fffcc000 { compatible = "atmel,at91rm9200-usart"; reg = <0xfffcc000 0x200>; - interrupts = <23 4 5>; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH 5>; atmel,use-dma-rx; atmel,use-dma-tx; pinctrl-names = "default";
@@ -490,7 +495,7 @@ usb1: gadget@fffb0000 { compatible = "atmel,at91rm9200-udc"; reg = <0xfffb0000 0x4000>; - interrupts = <11 4 2>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH 2>; status = "disabled"; }; };
@@ -515,7 +520,7 @@ usb0: ohci@00300000 { compatible = "atmel,at91rm9200-ohci", "usb-ohci"; reg = <0x00300000 0x100000>; - interrupts = <23 4 2>; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>; status = "disabled"; }; };
arch/arm/boot/dts/at91sam9260.dtsi +27 -22
185 lines not on this page · raw message
arch/arm/boot/dts/at91sam9263.dtsi +22 -21
174 lines not on this page · raw message
arch/arm/boot/dts/at91sam9g45.dtsi +25 -24
197 lines not on this page · raw message
arch/arm/boot/dts/at91sam9n12.dtsi +21 -20
165 lines not on this page · raw message
arch/arm/boot/dts/at91sam9x5.dtsi +28 -27
220 lines not on this page · raw message
arch/arm/boot/dts/sama5d3.dtsi +40 -39
316 lines not on this page · raw message
Signature · 7 lines
1.7.10.4 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH 1/5] ARM: at91: dt: use #include for all device trees
In reply to Jean-Christophe PLAGNIOL-VILLARDQuoted 1 line · Jean-Christophe PLAGNIOL-VILLARD
to prepare the switch to the macro.
sorry wrong ML
Quoted 2 lines
Signed-off-by Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox