ARM: atmel: add sama5d3xek board support
Subsystems (4)
cover ARM: atmel: add sama5d3xek board support
This patch series add sama5d3xek board support.
Included features
- boot from NAND flash, PMECC support, 4bit ECC @ 512 bytes sector
- boot from SPI flash support
- boot from SD card support
- LCD support
- EMAC support
- USB OHCI support
Will do
- Add GMAC support
- Add of control support
Changes in v3:
- Split new pmc register in a standalone patch
- Rebase to u-boot-atmel master branch
Changes in v2:
- Remove unneeded #undef
- Using string directly
- Add missed copyright
- Using pull up for usart Tx line
- Using pull up for spi cs
- make code more readable in clock.c file
- move LCD higher 8 bit to board file (This is board related)
Bo Shen (3):
ARM: at91: add Atmel sama5d3 SoC new pmc register
USB: ohci-at91: support sama5d3x devices
ARM: atmel: add sama5d3xek support
MAINTAINERS | 1 + arch/arm/cpu/armv7/at91/Makefile | 52 +++++ arch/arm/cpu/armv7/at91/clock.c | 125 ++++++++++++ arch/arm/cpu/armv7/at91/cpu.c | 90 +++++++++ arch/arm/cpu/armv7/at91/reset.c | 47 +++++ arch/arm/cpu/armv7/at91/sama5d3_devices.c | 196 ++++++++++++++++++ arch/arm/cpu/armv7/at91/timer.c | 139 +++++++++++++ arch/arm/include/asm/arch-at91/at91_dbu.h | 4 + arch/arm/include/asm/arch-at91/at91_pmc.h | 23 +++ arch/arm/include/asm/arch-at91/clk.h | 1 + arch/arm/include/asm/arch-at91/hardware.h | 2 + arch/arm/include/asm/arch-at91/sama5d3.h | 212 ++++++++++++++++++++ arch/arm/include/asm/arch-at91/sama5d3_smc.h | 79 ++++++++ board/atmel/sama5d3xek/Makefile | 51 +++++ board/atmel/sama5d3xek/sama5d3xek.c | 275 ++++++++++++++++++++++++++ boards.cfg | 3 + drivers/usb/host/ohci-at91.c | 14 +- include/configs/sama5d3xek.h | 245 +++++++++++++++++++++++ 18 files changed, 1557 insertions(+), 2 deletions(-) create mode 100644 arch/arm/cpu/armv7/at91/Makefile create mode 100644 arch/arm/cpu/armv7/at91/clock.c create mode 100644 arch/arm/cpu/armv7/at91/cpu.c create mode 100644 arch/arm/cpu/armv7/at91/reset.c create mode 100644 arch/arm/cpu/armv7/at91/sama5d3_devices.c create mode 100644 arch/arm/cpu/armv7/at91/timer.c create mode 100644 arch/arm/include/asm/arch-at91/sama5d3.h create mode 100644 arch/arm/include/asm/arch-at91/sama5d3_smc.h create mode 100644 board/atmel/sama5d3xek/Makefile create mode 100644 board/atmel/sama5d3xek/sama5d3xek.c create mode 100644 include/configs/sama5d3xek.h
Signature · 1 line
1.7.9.5
PATCH 1/3 ARM: at91: add Atmel sama5d3 SoC new pmc register
Add Atmel sama5d3 SoC new pmc register
---
Changes in v3:
- New splitted patch file.
Changes in v2:
- No change
arch/arm/include/asm/arch-at91/at91_pmc.h | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)
arch/arm/include/asm/arch-at91/at91_pmc.h +23 -0
@@ -55,7 +55,16 @@ typedef struct at91_pmc {u32 reserved5[21 ];u32 wpmr;/* 0xE4 Write Protect Mode Register (CAP0) */ u32 wpsr;/* 0xE8 Write Protect Status Register (CAP0) */ +#ifdef CONFIG_SAMA5D3 +u32 reserved6[8 ]; +u32 pcer1;/* 0x100 Periperial Clock Enable Register 1 */ +u32 pcdr1;/* 0x104 Periperial Clock Disable Register 1 */ +u32 pcsr1;/* 0x108 Periperial Clock Status Register 1 */ +u32 pcr;/* 0x10c Periperial Control Register */ +u32 ocr;/* 0x110 Oscillator Calibration Register */ +#else u32 reserved8[5 ]; +#endif } at91_pmc_t;#endif /* end not assembly */
@@ -82,6 +91,16 @@ typedef struct at91_pmc {#define AT91_PMC_MCKR_CSS_PLLB 0x00000003#define AT91_PMC_MCKR_CSS_MASK 0x00000003 +#ifdef CONFIG_SAMA5D3 +#define AT91_PMC_MCKR_PRES_1 0x00000000 +#define AT91_PMC_MCKR_PRES_2 0x00000010 +#define AT91_PMC_MCKR_PRES_4 0x00000020 +#define AT91_PMC_MCKR_PRES_8 0x00000030 +#define AT91_PMC_MCKR_PRES_16 0x00000040 +#define AT91_PMC_MCKR_PRES_32 0x00000050 +#define AT91_PMC_MCKR_PRES_64 0x00000060 +#define AT91_PMC_MCKR_PRES_MASK 0x00000070 +#else #define AT91_PMC_MCKR_PRES_1 0x00000000#define AT91_PMC_MCKR_PRES_2 0x00000004#define AT91_PMC_MCKR_PRES_4 0x00000008
@@ -90,6 +109,7 @@ typedef struct at91_pmc {#define AT91_PMC_MCKR_PRES_32 0x00000014#define AT91_PMC_MCKR_PRES_64 0x00000018#define AT91_PMC_MCKR_PRES_MASK 0x0000001C +#endif #ifdef CONFIG_AT91RM9200 #define AT91_PMC_MCKR_MDIV_1 0x00000000
@@ -100,6 +120,9 @@ typedef struct at91_pmc {#else #define AT91_PMC_MCKR_MDIV_1 0x00000000#define AT91_PMC_MCKR_MDIV_2 0x00000100 +#ifdef CONFIG_SAMA5D3 +#define AT91_PMC_MCKR_MDIV_3 0x00000300 +#endif #define AT91_PMC_MCKR_MDIV_4 0x00000200#define AT91_PMC_MCKR_MDIV_MASK 0x00000300#endif
Signature · 1 line
1.7.9.5
PATCH 1/3 ARM: at91: add Atmel sama5d3 SoC new pmc register
Dear Bo Shen,
Quoted 8 lines · Bo Shen
Add Atmel sama5d3 SoC new pmc register
Signed-off-by Bo Shen <[email protected]>---
Changes in v3:
- New splitted patch file.
Quoted 5 lines
Changes in v2:
- No change
arch/arm/include/asm/arch-at91/at91_pmc.h| 23 +++++++++++++++++++++++1 file changed, 23 insertions(+)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH 1/3 ARM: at91: fix and update README.at91 document
Dear Bo Shen,
Quoted 11 lines · Bo Shen
This patch implement following things
- The link no longer accessable
- Remove the error configuration command
- Update soldered data flash memory map
- Update at91sam9m10g45ek memory size to 128MiBSigned-off-by Bo Shen <[email protected]>---
doc/README.at91 | 23 ++++++-----------------1 file changed, 6 insertions(+), 17 deletions(-)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH 2/3 USB: ohci-at91: support sama5d3x devices
In reply to Andreas BießmannDear Bo Shen,
Quoted 8 lines · Bo Shen
Add OHCI support for sama5d3x devices
Signed-off-by Bo Shen <[email protected]>---
Changes in v3:
- Rebase to u-boot-atmel master branch
Quoted 5 lines
Changes in v2:
- No Change
drivers/usb/host/ohci-at91.c| 14 ++++++++++++--1 file changed, 12 insertions(+), 2 deletions(-)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH 2/3 ARM: at91: add at91sam9x5 and sama5d3x information
In reply to Andreas BießmannDear Bo Shen,
Quoted 9 lines · Bo Shen
This patch add following EK information
- at91sam9n12ek, at91sam9x5ek
- sama5d3xekSigned-off-by Bo Shen <[email protected]>---
doc/README.at91 | 42 ++++++++++++++++++++++++++++++++++++++++++1 file changed, 42 insertions(+)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH 3/3 ARM: atmel: add sama5d3xek support
In reply to Andreas BießmannDear Bo Shen,
Quoted 42 lines · Bo Shen
Add sama5d3xek support with following feature
- boot from NAND flash, PMECC support, 4bit ECC @ 512 bytes sector
- boot from SPI flash support
- boot from SD card support
- LCD support
- EMAC support
- USB OHCI supportSigned-off-by Bo Shen <[email protected]>---
Changes in v3:
- Split new pmc register in a standalone patch
- The EMAC support need: net: macb: using AT91FAMILY replace #ifdeferry
- http://patchwork.ozlabs.org/patch/239064/Changes in v2:
- Remove unneeded #undef
- Using string directly
- Add missed copyright
- Using pull up for usart Tx line
- Using pull up for spi cs
- make code more readable inclock.cfile
- move LCD higher 8 bit to board file (This is board related)MAINTAINERS | 1 + arch/arm/cpu/armv7/at91/Makefile | 52 +++++ arch/arm/cpu/armv7/at91/clock.c | 125 ++++++++++++ arch/arm/cpu/armv7/at91/cpu.c | 90 +++++++++ arch/arm/cpu/armv7/at91/reset.c | 47 +++++ arch/arm/cpu/armv7/at91/sama5d3_devices.c | 196 ++++++++++++++++++ arch/arm/cpu/armv7/at91/timer.c | 139 +++++++++++++ arch/arm/include/asm/arch-at91/at91_dbu.h | 4 + arch/arm/include/asm/arch-at91/clk.h | 1 + arch/arm/include/asm/arch-at91/hardware.h | 2 + arch/arm/include/asm/arch-at91/sama5d3.h | 212 ++++++++++++++++++++ arch/arm/include/asm/arch-at91/sama5d3_smc.h | 79 ++++++++ board/atmel/sama5d3xek/Makefile | 51 +++++ board/atmel/sama5d3xek/sama5d3xek.c | 275 ++++++++++++++++++++++++++ boards.cfg | 3 + include/configs/sama5d3xek.h | 245 +++++++++++++++++++++++ 16 files changed, 1522 insertions(+)
Quoted 11 lines
create mode 100644
arch/arm/cpu/armv7/at91/Makefilecreate mode 100644arch/arm/cpu/armv7/at91/clock.ccreate mode 100644arch/arm/cpu/armv7/at91/cpu.ccreate mode 100644arch/arm/cpu/armv7/at91/reset.ccreate mode 100644arch/arm/cpu/armv7/at91/sama5d3_devices.ccreate mode 100644arch/arm/cpu/armv7/at91/timer.ccreate mode 100644arch/arm/include/asm/arch-at91/sama5d3.hcreate mode 100644arch/arm/include/asm/arch-at91/sama5d3_smc.hcreate mode 100644 board/atmel/sama5d3xek/Makefile create mode 100644board/atmel/sama5d3xek/sama5d3xek.ccreate mode 100644include/configs/sama5d3xek.h
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH 3/3 ARM: at91: add NAND partition table and index
In reply to Andreas BießmannDear Bo Shen,
Quoted 10 lines · Bo Shen
Add NAND partition table, EK board support boot up NAND flash using the same NAND partition table
Add Index in this file
Signed-off-by Bo Shen <[email protected]>---
doc/README.at91 | 21 ++++++++++++++++++++-1 file changed, 20 insertions(+), 1 deletion(-)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH 2/3 USB: ohci-at91: support sama5d3x devices
In reply to Bo ShenAdd OHCI support for sama5d3x devices
---
Changes in v3:
- Rebase to u-boot-atmel master branch
Changes in v2:
- No Change
drivers/usb/host/ohci-at91.c | 14 ++++++++++++-- 1 file changed, 12 insertions(+), 2 deletions(-)
drivers/usb/host/ohci-at91.c +12 -2
@@ -42,7 +42,7 @@ int usb_cpu_init(void)while ((readl (&pmc->sr) &AT91_PMC_LOCKB ) !=AT91_PMC_LOCKB ) ;#elif defined(CONFIG_AT91SAM9G45 ) || defined(CONFIG_AT91SAM9M10G45 ) || \ - defined(CONFIG_AT91SAM9X5 ) + defined(CONFIG_AT91SAM9X5 ) || defined(CONFIG_SAMA5D3 )/* Enable UPLL */ writel (readl (&pmc->uckr) |AT91_PMC_UPLLEN |AT91_PMC_BIASEN , &pmc->uckr);
@@ -54,7 +54,12 @@ int usb_cpu_init(void)#endif /* Enable USB host clock. */ +#ifdef CONFIG_SAMA5D3 +writel (1 << (ATMEL_ID_UHP -32 ), &pmc->pcer1); +#else writel (1 <<ATMEL_ID_UHP , &pmc->pcer); +#endif +#ifdef CONFIG_AT91SAM9261 writel (ATMEL_PMC_UHP |AT91_PMC_HCK0 , &pmc->scer);#else
@@ -69,7 +74,12 @@ int usb_cpu_stop(void)at91_pmc_t *pmc = (at91_pmc_t *)ATMEL_BASE_PMC ;/* Disable USB host clock. */ +#ifdef CONFIG_SAMA5D3 +writel (1 << (ATMEL_ID_UHP -32 ), &pmc->pcdr1); +#else writel (1 <<ATMEL_ID_UHP , &pmc->pcdr); +#endif +#ifdef CONFIG_AT91SAM9261 writel (ATMEL_PMC_UHP |AT91_PMC_HCK0 , &pmc->scdr);#else
@@ -83,7 +93,7 @@ int usb_cpu_stop(void)while ((readl (&pmc->sr) &AT91_PMC_LOCKB ) !=0 ) ;#elif defined(CONFIG_AT91SAM9G45 ) || defined(CONFIG_AT91SAM9M10G45 ) || \ - defined(CONFIG_AT91SAM9X5 ) + defined(CONFIG_AT91SAM9X5 ) || defined(CONFIG_SAMA5D3 )/* Disable UPLL */ writel (readl (&pmc->uckr) & (~AT91_PMC_UPLLEN ), &pmc->uckr);while ((readl (&pmc->sr) &AT91_PMC_LOCKU ) ==AT91_PMC_LOCKU )
Signature · 1 line
1.7.9.5
PATCH 3/3 ARM: atmel: add sama5d3xek support
In reply to Bo ShenAdd sama5d3xek support with following feature
- boot from NAND flash, PMECC support, 4bit ECC @ 512 bytes sector
- boot from SPI flash support
- boot from SD card support
- LCD support
- EMAC support
- USB OHCI support
---
Changes in v3:
- Split new pmc register in a standalone patch
- The EMAC support need: net: macb: using AT91FAMILY replace #ifdeferry
- http://patchwork.ozlabs.org/patch/239064/
Changes in v2:
- Remove unneeded #undef
- Using string directly
- Add missed copyright
- Using pull up for usart Tx line
- Using pull up for spi cs
- make code more readable in clock.c file
- move LCD higher 8 bit to board file (This is board related)
MAINTAINERS | 1 + arch/arm/cpu/armv7/at91/Makefile | 52 +++++ arch/arm/cpu/armv7/at91/clock.c | 125 ++++++++++++ arch/arm/cpu/armv7/at91/cpu.c | 90 +++++++++ arch/arm/cpu/armv7/at91/reset.c | 47 +++++ arch/arm/cpu/armv7/at91/sama5d3_devices.c | 196 ++++++++++++++++++ arch/arm/cpu/armv7/at91/timer.c | 139 +++++++++++++ arch/arm/include/asm/arch-at91/at91_dbu.h | 4 + arch/arm/include/asm/arch-at91/clk.h | 1 + arch/arm/include/asm/arch-at91/hardware.h | 2 + arch/arm/include/asm/arch-at91/sama5d3.h | 212 ++++++++++++++++++++ arch/arm/include/asm/arch-at91/sama5d3_smc.h | 79 ++++++++ board/atmel/sama5d3xek/Makefile | 51 +++++ board/atmel/sama5d3xek/sama5d3xek.c | 275 ++++++++++++++++++++++++++ boards.cfg | 3 + include/configs/sama5d3xek.h | 245 +++++++++++++++++++++++ 16 files changed, 1522 insertions(+) create mode 100644 arch/arm/cpu/armv7/at91/Makefile create mode 100644 arch/arm/cpu/armv7/at91/clock.c create mode 100644 arch/arm/cpu/armv7/at91/cpu.c create mode 100644 arch/arm/cpu/armv7/at91/reset.c create mode 100644 arch/arm/cpu/armv7/at91/sama5d3_devices.c create mode 100644 arch/arm/cpu/armv7/at91/timer.c create mode 100644 arch/arm/include/asm/arch-at91/sama5d3.h create mode 100644 arch/arm/include/asm/arch-at91/sama5d3_smc.h create mode 100644 board/atmel/sama5d3xek/Makefile create mode 100644 board/atmel/sama5d3xek/sama5d3xek.c create mode 100644 include/configs/sama5d3xek.h
MAINTAINERS +1 -0
@@ -918,6 +918,7 @@ Matt Sealey <[email protected]> Bo Shen <[email protected]> at91sam9x5ek ARM926EJS (AT91SAM9G15,G25,G35,X25,X35 SoC) + sama5d3xek ARMV7 (SAMA5D31, D33, D34, D35 SoC) Rajeshwari Shinde <[email protected]>
arch/arm/cpu/armv7/at91/Makefile new file +52 -0
52 lines not on this page · raw message
arch/arm/cpu/armv7/at91/clock.c new file +125 -0
125 lines not on this page · raw message
arch/arm/cpu/armv7/at91/cpu.c new file +90 -0
90 lines not on this page · raw message
arch/arm/cpu/armv7/at91/reset.c new file +47 -0
47 lines not on this page · raw message
arch/arm/cpu/armv7/at91/sama5d3_devices.c new file +196 -0
196 lines not on this page · raw message
arch/arm/cpu/armv7/at91/timer.c new file +139 -0
139 lines not on this page · raw message
arch/arm/include/asm/arch-at91/at91_dbu.h +4 -0
@@ -38,4 +38,8 @@ typedef struct at91_dbu {#define AT91_DBU_CID_ARCH_9xx 0x01900000#define AT91_DBU_CID_ARCH_9XExx 0x02900000 +#define AT91_DBU_CIDR_MASK 0x1f +#define AT91_DBU_CIDR 0x40 +#define AT91_DBU_EXID 0x44 +#endif
arch/arm/include/asm/arch-at91/clk.h +1 -0
@@ -95,4 +95,5 @@ static inline unsigned long get_mci_clk_rate(void) }int at91_clock_init (unsigned long main_clock); +void at91_periph_clk_enable (int id);#endif /* __ASM_ARM_ARCH_CLK_H__ */
arch/arm/include/asm/arch-at91/hardware.h +2 -0
@@ -43,6 +43,8 @@# include <asm/arch/at91cap9.h> #elif defined(CONFIG_AT91X40 )# include <asm/arch/at91x40.h> +#elif defined(CONFIG_SAMA5D3 ) +# include <asm/arch/sama5d3.h> #else # error "Unsupported AT91 processor"#endif
arch/arm/include/asm/arch-at91/sama5d3.h new file +212 -0
212 lines not on this page · raw message
arch/arm/include/asm/arch-at91/sama5d3_smc.h new file +79 -0
79 lines not on this page · raw message
board/atmel/sama5d3xek/Makefile new file +51 -0
51 lines not on this page · raw message
board/atmel/sama5d3xek/sama5d3xek.c new file +275 -0
275 lines not on this page · raw message
boards.cfg +3 -0
@@ -249,6 +249,9 @@ am335x_evm_uart5 arm armv7 am335x ti am335x_evm_usbspl arm armv7 am335x ti am33xx am335x_evm:SERIAL1,CONS_INDEX=1,SPL_USBETH_SUPPORT ti814x_evm arm armv7 ti814x ti am33xx pcm051 arm armv7 pcm051 phytec am33xx pcm051 +sama5d3xek_mmc arm armv7 sama5d3xek atmel at91 sama5d3xek:SAMA5D3,SYS_USE_MMC +sama5d3xek_nandflash arm armv7 sama5d3xek atmel at91 sama5d3xek:SAMA5D3,SYS_USE_NANDFLASH +sama5d3xek_spiflash arm armv7 sama5d3xek atmel at91 sama5d3xek:SAMA5D3,SYS_USE_SERIALFLASH highbank arm armv7 highbank - highbank m53evk arm armv7 m53evk denx mx5 m53evk:IMX_CONFIG=board/denx/m53evk/imximage.cfg mx51_efikamx arm armv7 mx51_efikamx genesi mx5 mx51_efikamx:MACH_TYPE=MACH_TYPE_MX51_EFIKAMX,IMX_CONFIG=board/genesi/mx51_efikamx/imximage_mx.cfg
include/configs/sama5d3xek.h new file +245 -0
245 lines not on this page · raw message
Signature · 1 line
1.7.9.5