Skip to contentSkip to conversation

misc: Add Lattice XP2 FPGA internal flash programming via SPI

PATCH New Stefan Roese 1 participant 1 message May 24, 2013 Char and misc drivers

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 misc: Add Lattice XP2 FPGA internal flash programming via SPI

This option enables support for programming of the FPGA's internal flash of the Lattice XP2 FPGA family via SPI. The newly programmed bitstream will also be loaded into the internal SRAM (refresh).

Note: The XP2 needs at least 3 clocks to be sent to the FPGA with inactive CS for some commands. Since the MPC5200 PSC SPI controller does not support de-activating the CS, we need to re-configure the PSC port from SPI to GPIO and generate the clocks with inactive CS this way. After generating these clocks, the PSC is configured to SPI controller again. So this current implementation is very SPI controller specific and this driver will only work on the MPC5200 PSC SPI controller.

Here an example on my custom MPC5200 based board:

$ echo 1 > /sys/class/firmware/lattice-xp2.bit/loading
$ cat a3m071-fpga.jed > /sys/class/firmware/lattice-xp2.bit/data
$ echo 0 > /sys/class/firmware/lattice-xp2.bit/loading

leads to these messages:

lattice-xp2 spi1.0: Security fuse will be set!
lattice-xp2 spi1.0: FPGA Lattice XP2-17 detected
lattice-xp2 spi1.0: FPGA data verified!
lattice-xp2 spi1.0: FPGA security fuse programmed
lattice-xp2 spi1.0: FPGA DONE fuse programmed
lattice-xp2 spi1.0: FPGA successfully refreshed!

Cc Arnd Bergmann <[email protected]>
Cc Greg Kroah-Hartman <[email protected]>

---
I know that the re-configuration of the pins (SPI vs GPIO) as described above could/should be done in a "clean way" via pinctrl. But currently there is no pinctrl support for MPC52xx and the scope of this project doesn't really allow me to implement this infrastructure. Perhaps somebody else will find the time to do this later. But I'm pretty sure that this driver is "as-is" helpful for other users/developers.

Stefan

 drivers/misc/Kconfig              |  12 +
 drivers/misc/Makefile             |   1 +
 drivers/misc/lattice-xp2-config.c | 827 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 840 insertions(+)
 create mode 100644 drivers/misc/lattice-xp2-config.c
drivers/misc/Kconfig +12 -0
index c002d86..dea2ed3 100644
@@ -518,6 +518,18 @@ config LATTICE_ECP3_CONFIG
 
 	  If unsure, say N.
 
+config LATTICE_XP2_CONFIG
+	tristate "Lattice XP2 FPGA internal flash programming via SPI"
+	depends on SPI && SYSFS && PPC_MPC52xx
+	select FW_LOADER
+	default	n
+	help
+	  This option enables support for programming of the FPGA's internal
+	  flash of the Lattice XP2 FPGA family via SPI. The newly programmed
+	  bitstream will also be loaded into the internal SRAM (refresh).
+
+	  If unsure, say N.
+
 config SRAM
 	bool "Generic on-chip SRAM driver"
 	depends on HAS_IOMEM
drivers/misc/Makefile +1 -0
index c235d5b..4fb82cf 100644
@@ -52,4 +52,5 @@ obj-$(CONFIG_ALTERA_STAPL)	+=altera-stapl/
 obj-$(CONFIG_INTEL_MEI)		+= mei/
 obj-$(CONFIG_VMWARE_VMCI)	+= vmw_vmci/
 obj-$(CONFIG_LATTICE_ECP3_CONFIG)	+= lattice-ecp3-config.o
+obj-$(CONFIG_LATTICE_XP2_CONFIG)	+= lattice-xp2-config.o
 obj-$(CONFIG_SRAM)		+= sram.o
drivers/misc/lattice-xp2-config.c new file +827 -0

827 lines not on this page · raw message

Signature · 1 line
1.8.2.3