Skip to contentSkip to conversation

bond-mode 4 bridge-utils 3.x kernel not fully working

Bridge Jelle de Jong 2 participants 4 messages May 28, 2013 – Jun 17, 2013 Ethernet bridge

lore
Share & tools
lore
#0 lore raw

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Hello everybody,

I also sent this email to [email protected]

I spent ours debugging and finding out what points to the problem.

I run kvm quests with bridged networking on a bonding lacp set-up, with the 2.6 kernel this has been working fine for years. But with the 3.x kernel this doesn?t work any more.

Traffic comes out the KVM quests but doesn?t come in. If I disable bonding everything just works again.

# working with 2.6 not working with 3.x
cat /etc/network/interfaces
auto lo
  iface lo inet loopback

auto bond0
iface bond0 inet manual
slaves eth0 eth1
bond-mode 4
bond-miimon 100
pre-up /sbin/ifconfig bond0 mtu 9000

auto br0
iface br0 inet dhcp
bridge_fd 0
bridge_stp on
bridge_ports bond0

# working with 3.x but no bonding!!
cat /etc/network/interfaces
auto lo
  iface lo inet loopback

auto eth0
iface eth0 inet manual
mtu 900

auto br0
iface br0 inet dhcp
bridge_fd 0
bridge_stp on
bridge_ports eth0

# uname -a
Linux viktoriya 3.2.0-4-amd64 #1 SMP Debian 3.2.41-2+deb7u2 x86_64
GNU/Linux

bridge-utils version 1.5-6

I already checked iptabls, ebtables there are no running rules and the bellow on zero or one doesn't make a difference either also disabling bridge_stp off or bridge_maxwait 0 doesn't seem to help.

/bin/echo "0" > /proc/sys/net/bridge/bridge-nf-call-arptables /bin/echo "0" > /proc/sys/net/bridge/bridge-nf-call-ip6tables /bin/echo "0" > /proc/sys/net/bridge/bridge-nf-call-iptables

Any ideas?

Kind regards,

Jelle de Jong
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)

iJwEAQECAAYFAlGlOXMACgkQ1WclBW9j5HkK/wP+Mtu5FB9gU1tAlDnHBDH9x98p 1hGhXTOY81wuDdN3WzjlOLvlIevRuFiVm2b+HrhFqI5Bvh9SHb06FPoaHW92WdNj Xh32N/a2ghR161tATlltAxbSUuLT9+SuNA2GQ8zdEG7u+uKMBOeecPgBccqRa1NV lHDEGUKqlhA40c0lRY0=
=kJ2M
-----END PGP SIGNATURE-----

#1 lore raw
Quoted 11 lines · Jelle de Jong

Traffic comes out the KVM quests but doesn?t come in. If I disable bonding everything just works again.

auto bond0
iface bond0 inet manual
slaves eth0 eth1
bond-mode 4
bond-miimon 100
pre-up /sbin/ifconfig bond0 mtu 9000

Quoted 3 lines

auto eth0
iface eth0 inet manual
mtu 900

Does this one really say mtu 900 instead of 9000? Is your eth1 up?
Did you try non-kvm traffic over the bonding interface? Is the switch in LACP mode?

Regards,

Wilco Baan Hofman

#2 lore raw

Hi Wilco,

Quoted 10 lines · Wilco Baan Hofman
Quoted 9 lines

Traffic comes out the KVM quests but doesn?t come in. If I disable bonding everything just works again.

auto bond0
iface bond0 inet manual
slaves eth0 eth1
bond-mode 4
bond-miimon 100
pre-up /sbin/ifconfig bond0 mtu 9000

Quoted 6 lines
Quoted 3 lines

auto eth0
iface eth0 inet manual
mtu 900

Does this one really say mtu 900 instead of 9000?
Is your eth1 up?

No, it was mtu 9000 (sorry for the confusion)

Quoted 2 lines

Did you try non-kvm traffic over the bonding interface? Is the switch in LACP mode?

Yes the Cisco switch is in LACP mode and I use intel nics.
http://paste.debian.net/6686/

I noticed that incoming IPv6 traffic doesn't work anymore, the br0 interface recieved the IPv6 IP and I can ping it on the local-host but not from an other server, the IPv6 works again to moment I remove the bonding.

Remember tcpdump does show traffic coming in and out the br0 device but not the vnet0 device that is used for the kvm guest.

Kind regards,

Jelle de Jong

#3 lore raw
In reply to Jelle de Jong

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 33 lines · Jelle de Jong

I also sent this email to [email protected]

I spent ours debugging and finding out what points to the problem.

I run kvm quests with bridged networking on a bonding lacp set-up, with the 2.6 kernel this has been working fine for years. But with the 3.x kernel this doesn?t work any more.

Traffic comes out the KVM quests but doesn?t come in. If I disable bonding everything just works again.

# working with 2.6 not working with 3.x cat
/etc/network/interfaces auto lo iface lo inet loopback

auto bond0 iface bond0 inet manual slaves eth0 eth1 bond-mode 4 bond-miimon 100 pre-up /sbin/ifconfig bond0 mtu 9000

auto br0 iface br0 inet dhcp bridge_fd 0 bridge_stp on bridge_ports bond0

# working with 3.x but no bonding!! cat /etc/network/interfaces 
auto lo iface lo inet loopback

auto eth0 iface eth0 inet manual mtu 900

auto br0 iface br0 inet dhcp bridge_fd 0 bridge_stp on bridge_ports eth0

# uname -a Linux viktoriya 3.2.0-4-amd64 #1 SMP Debian
3.2.41-2+deb7u2 x86_64 GNU/Linux

bridge-utils version 1.5-6

Quoted 7 lines

I already checked iptabls, ebtables there are no running rules and the bellow on zero or one doesn't make a difference either also disabling bridge_stp off or bridge_maxwait 0 doesn't seem to help.

/bin/echo "0" > /proc/sys/net/bridge/bridge-nf-call-arptables /bin/echo "0" > /proc/sys/net/bridge/bridge-nf-call-ip6tables /bin/echo "0" > /proc/sys/net/bridge/bridge-nf-call-iptables

Anybody? I?m still unable to use bonding lacp & bridge & vlans with kvm guest in a 3.x kernel (2.6 is working fine)

Kind regards,

Jelle de Jong
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)

iJwEAQECAAYFAlG+7DcACgkQ1WclBW9j5HmXUwP9EXmWz7h2K+3LkWk0NbfAdxd6 nTb2nTWGX/659DqRIIIJbxz3haxxdDIUqjS6QBkAyaG8zJLwNSa2Ks4KdL5mrRJw hSJOqRNhv7u92tNv1uZeN+bZ8huFvvPgMaMd4Mx/vCta1isSOtSzbS9devjg4SFP 0ZX6DhG32uELhpk1AtA=
=NrXT
-----END PGP SIGNATURE-----