iMX nand BBT problem
Hi,
when upgrading from 2013.05.1 to 2013.06 on an i.MX35 I get the following log :
- initial log :
barebox 2013.05.1-00001-ga8e8785 #25 Mon Jul 1 17:12:14 CEST 2013
Board: Eukrea CPUIMX35
detected i.MX35 revision 2.1
netconsole: registered as cs1
nand: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit), page size: 2048, OOB size: 64mdio_bus: miibus0: probed
imx-ipu-fb imx-ipu-fb: i.MX Framebuffer driver
imx-esdhc imx-esdhc0: registered as imx-esdhc0
ehci ehci0: USB EHCI 1.00
malloc space: 0x87700000 -> 0x87efffff (size 8 MiB) running /env/bin/init...
--> upgrade barebox :
barebox 2013.06.0-00001-gf355cf4 #26 Mon Jul 1 17:57:52 CEST 2013
Board: Eukrea CPUIMX35
detected i.MX35 revision 2.1
netconsole: registered as cs1
nand: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit), page size: 2048, OOB size: 64
nand: Bad block table not found for chip 0
nand: Bad block table not found for chip 0imx_nand imx_nand: no BBT found. create one using the imx_nand_bbm commandmdio_bus: miibus0: probed
imx-ipu-fb imx-ipu-fb: i.MX Framebuffer driver
imx-esdhc imx-esdhc0: registered as imx-esdhc0
ehci ehci0: USB EHCI 1.00
malloc space: 0x87700000 -> 0x87efffff (size 8 MiB)
envfs: wrong magic on /dev/env0
no valid environment found on /dev/env0. Using default environment running /env/bin/init...
no MAC address set for eth0. please enter the one found on your board:
00:12:34:56:78:90 saving environment
Once I reset the board I can see that the env was not saved and I get prompted again for the MAC address.
Any idea of what can be wrong there ?
This board is configured in external boot from a 2k NAND (and was already using flash BBT), and the kernel and rootfs still run without any visible problem.
Eric
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
HI Eric,
Quoted 41 lines · Eric Bénard
Hi,
when upgrading from 2013.05.1 to 2013.06 on an i.MX35 I get the following log :
- initial log :
barebox 2013.05.1-00001-ga8e8785 #25 Mon Jul 1 17:12:14 CEST 2013
Board: Eukrea CPUIMX35
detected i.MX35 revision 2.1
netconsole: registered as cs1
nand: Manufacturer ID:0x2c, Chip ID:0xda(Micron NAND 256MiB 3,3V 8-bit), page size: 2048, OOB size: 64mdio_bus: miibus0: probed
imx-ipu-fb imx-ipu-fb: i.MX Framebuffer driver
imx-esdhc imx-esdhc0: registered as imx-esdhc0
ehci ehci0: USB EHCI 1.00
malloc space:0x87700000->0x87efffff(size 8 MiB) running /env/bin/init...--> upgrade barebox :
barebox 2013.06.0-00001-gf355cf4 #26 Mon Jul 1 17:57:52 CEST 2013
Board: Eukrea CPUIMX35
detected i.MX35 revision 2.1
netconsole: registered as cs1
nand: Manufacturer ID:0x2c, Chip ID:0xda(Micron NAND 256MiB 3,3V 8-bit), page size: 2048, OOB size: 64
nand: Bad block table not found for chip 0
nand: Bad block table not found for chip 0imx_nandimx_nand: no BBT found. create one using theimx_nand_bbmcommandmdio_bus: miibus0: probed
imx-ipu-fb imx-ipu-fb: i.MX Framebuffer driver
imx-esdhc imx-esdhc0: registered as imx-esdhc0
ehci ehci0: USB EHCI 1.00
malloc space:0x87700000->0x87efffff(size 8 MiB)
envfs: wrong magic on/dev/env0
no valid environment found on/dev/env0. Using default environment running /env/bin/init...
no MAC address set for eth0. please enter the one found on your board:
00:12:34:56:78:90 saving environment
Quoted 8 lines
Once I reset the board I can see that the env was not saved and I get prompted again for the MAC address.
Any idea of what can be wrong there ?
This board is configured in external boot from a 2k NAND (and was already using flash BBT), and the kernel and rootfs still run without any visible problem.
Are you sure this happens between 2013.05.1 and 2013.06.0? The only changes in the mtd stuff are:
ae6f751 nand_base: sync flash detection functions with linux 3.9's code c8af035 Merge branch 'for-next/misc'
7c15fd1 NAND: imx: Fix memory leak
d8ee54f mtd: Nand: Use dev_add_param_bool for erasebad parameter 7c6c61f treewide: Use dev_add_param_int_ro where possible 973176d mtd: update NAND manufacturer names from the kernel 4c2bdc8 nand_base: detect more ONFI flash
So the only patches which seem to change something are from you ;)
Does the 'md' command still work and shows meaningful content in the NAND?
Sascha
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Quoted 62 lines · Eric Bénard
Quoted 41 lines
Hi,
when upgrading from 2013.05.1 to 2013.06 on an i.MX35 I get the following log :
- initial log :
barebox 2013.05.1-00001-ga8e8785 #25 Mon Jul 1 17:12:14 CEST 2013
Board: Eukrea CPUIMX35
detected i.MX35 revision 2.1
netconsole: registered as cs1
nand: Manufacturer ID:0x2c, Chip ID:0xda(Micron NAND 256MiB 3,3V 8-bit), page size: 2048, OOB size: 64mdio_bus: miibus0: probed
imx-ipu-fb imx-ipu-fb: i.MX Framebuffer driver
imx-esdhc imx-esdhc0: registered as imx-esdhc0
ehci ehci0: USB EHCI 1.00
malloc space:0x87700000->0x87efffff(size 8 MiB) running /env/bin/init...--> upgrade barebox :
barebox 2013.06.0-00001-gf355cf4 #26 Mon Jul 1 17:57:52 CEST 2013
Board: Eukrea CPUIMX35
detected i.MX35 revision 2.1
netconsole: registered as cs1
nand: Manufacturer ID:0x2c, Chip ID:0xda(Micron NAND 256MiB 3,3V 8-bit), page size: 2048, OOB size: 64
nand: Bad block table not found for chip 0
nand: Bad block table not found for chip 0imx_nandimx_nand: no BBT found. create one using theimx_nand_bbmcommandmdio_bus: miibus0: probed
imx-ipu-fb imx-ipu-fb: i.MX Framebuffer driver
imx-esdhc imx-esdhc0: registered as imx-esdhc0
ehci ehci0: USB EHCI 1.00
malloc space:0x87700000->0x87efffff(size 8 MiB)
envfs: wrong magic on/dev/env0
no valid environment found on/dev/env0. Using default environment running /env/bin/init...
no MAC address set for eth0. please enter the one found on your board:
00:12:34:56:78:90 saving environmentQuoted 8 lines
Once I reset the board I can see that the env was not saved and I get prompted again for the MAC address.
Any idea of what can be wrong there ?
This board is configured in external boot from a 2k NAND (and was already using flash BBT), and the kernel and rootfs still run without any visible problem.
Are you sure this happens between 2013.05.1 and 2013.06.0? The only changes in the mtd stuff are:
ae6f751
nand_base: sync flash detection functions with linux 3.9's code c8af035 Merge branch 'for-next/misc'
7c15fd1 NAND: imx: Fix memory leak
d8ee54f mtd: Nand: Usedev_add_param_boolfor erasebad parameter 7c6c61f treewide: Usedev_add_param_int_rowhere possible 973176d mtd: update NAND manufacturer names from the kernel 4c2bdc8nand_base: detect more ONFI flash
Quoted 4 lines
So the only patches which seem to change something are from you ;)
Does the 'md' command still work and shows meaningful content in the NAND?
I think the best way here is using "git-bisect" to find this issue.
---
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Hi Sascha,
Quoted 62 lines · Sascha Hauer
Quoted 41 lines · Eric Bénard
Hi,
when upgrading from 2013.05.1 to 2013.06 on an i.MX35 I get the following log :
- initial log :
barebox 2013.05.1-00001-ga8e8785 #25 Mon Jul 1 17:12:14 CEST 2013
Board: Eukrea CPUIMX35
detected i.MX35 revision 2.1
netconsole: registered as cs1
nand: Manufacturer ID:0x2c, Chip ID:0xda(Micron NAND 256MiB 3,3V 8-bit), page size: 2048, OOB size: 64mdio_bus: miibus0: probed
imx-ipu-fb imx-ipu-fb: i.MX Framebuffer driver
imx-esdhc imx-esdhc0: registered as imx-esdhc0
ehci ehci0: USB EHCI 1.00
malloc space:0x87700000->0x87efffff(size 8 MiB) running /env/bin/init...--> upgrade barebox :
barebox 2013.06.0-00001-gf355cf4 #26 Mon Jul 1 17:57:52 CEST 2013
Board: Eukrea CPUIMX35
detected i.MX35 revision 2.1
netconsole: registered as cs1
nand: Manufacturer ID:0x2c, Chip ID:0xda(Micron NAND 256MiB 3,3V 8-bit), page size: 2048, OOB size: 64
nand: Bad block table not found for chip 0
nand: Bad block table not found for chip 0imx_nandimx_nand: no BBT found. create one using theimx_nand_bbmcommandmdio_bus: miibus0: probed
imx-ipu-fb imx-ipu-fb: i.MX Framebuffer driver
imx-esdhc imx-esdhc0: registered as imx-esdhc0
ehci ehci0: USB EHCI 1.00
malloc space:0x87700000->0x87efffff(size 8 MiB)
envfs: wrong magic on/dev/env0
no valid environment found on/dev/env0. Using default environment running /env/bin/init...
no MAC address set for eth0. please enter the one found on your board:
00:12:34:56:78:90 saving environmentQuoted 8 lines
Once I reset the board I can see that the env was not saved and I get prompted again for the MAC address.
Any idea of what can be wrong there ?
This board is configured in external boot from a 2k NAND (and was already using flash BBT), and the kernel and rootfs still run without any visible problem.
Are you sure this happens between 2013.05.1 and 2013.06.0? The only changes in the mtd stuff are:
ae6f751
nand_base: sync flash detection functions with linux 3.9's code c8af035 Merge branch 'for-next/misc'
7c15fd1 NAND: imx: Fix memory leak
d8ee54f mtd: Nand: Usedev_add_param_boolfor erasebad parameter 7c6c61f treewide: Usedev_add_param_int_rowhere possible 973176d mtd: update NAND manufacturer names from the kernel 4c2bdc8nand_base: detect more ONFI flash
Quoted 2 lines
So the only patches which seem to change something are from you ;)
I know and I feared I broke something :-( but I don't see where at the moment.
I'll spend more time on this and provide more details shortly.
Eric
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox