Add sound in SAM9x5 DTS
Subsystems (2)
cover Add sound in SAM9x5 DTS
As the sam9x5-wm8731 machine driver has been merged, we have now to add the device tree nodes...
And here they are !
(Based on next-20130812)
Tested on at91sam9g35-ek
[I didn't add the DT list, as far as there's no new binding, we don't have to bother themi, right ?]
Richard Genoud (4):
ARM: AT91: DTS: sam9x5: add SSC DMA parameters
ARM: AT91: DTS: sam9x5ek: add WM8731 codec
ARM: AT91: DTS: sam9x5ek: enable SSC
ARM: AT91: DTS: sam9x5ek: add sound configuration
arch/arm/boot/dts/at91sam9x5.dtsi | 3 +++ arch/arm/boot/dts/at91sam9x5ek.dtsi | 24 ++++++++++++++++++++++++ 2 files changed, 27 insertions(+)
Signature · 1 line
1.7.10.4
PATCH 1/4 ARM: AT91: DTS: sam9x5: add SSC DMA parameters
--- arch/arm/boot/dts/at91sam9x5.dtsi | 3 +++ 1 file changed, 3 insertions(+)
arch/arm/boot/dts/at91sam9x5.dtsi +3 -0
@@ -542,6 +542,9 @@ compatible = "atmel,at91sam9g45-ssc"; reg = <0xf0010000 0x4000>; interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>; + dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(13)>, + <&dma0 1 AT91_DMA_CFG_PER_ID(14)>; + dma-names = "tx", "rx"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; status = "disabled";
Signature · 1 line
1.7.10.4
PATCH 2/4 ARM: AT91: DTS: sam9x5ek: add WM8731 codec
In reply to Richard GenoudThe WM8731 codec on sam9x5ek board is on i2c, address 1A
--- arch/arm/boot/dts/at91sam9x5ek.dtsi | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm/boot/dts/at91sam9x5ek.dtsi +5 -0
@@ -59,6 +59,11 @@ i2c0: i2c at f8010000 { status = "okay"; + + wm8731: wm8731 at 1a { + compatible = "wm8731"; + reg = <0x1a>; + }; }; pinctrl at fffff400 {
Signature · 1 line
1.7.10.4
PATCH 3/4 ARM: AT91: DTS: sam9x5ek: enable SSC
In reply to Richard GenoudEnable the SSC needed for the WM8731 codec
--- arch/arm/boot/dts/at91sam9x5ek.dtsi | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm/boot/dts/at91sam9x5ek.dtsi +4 -0
@@ -95,6 +95,10 @@ watchdog at fffffe40 { status = "okay"; }; + + ssc0: ssc at f0010000 { + status = "okay"; + }; }; usb0: ohci at 00600000 {
Signature · 1 line
1.7.10.4
PATCH 4/4 ARM: AT91: DTS: sam9x5ek: add sound configuration
In reply to Richard GenoudThe sam9x5ek board has 2 jacks:
headphone wired on RHPOUT/LHPOUT of the wm8731
line in wired on LLINEIN/RLINEIN of the wm8731
--- arch/arm/boot/dts/at91sam9x5ek.dtsi | 15 +++++++++++++++ 1 file changed, 15 insertions(+)
arch/arm/boot/dts/at91sam9x5ek.dtsi +15 -0
@@ -113,4 +113,19 @@ status = "okay"; }; }; + + sound { + compatible = "atmel,sam9x5-wm8731-audio"; + + atmel,model = "wm8731 @ AT91SAM9X5EK"; + + atmel,audio-routing = + "Headphone Jack", "RHPOUT", + "Headphone Jack", "LHPOUT", + "LLINEIN", "Line In Jack", + "RLINEIN", "Line In Jack"; + + atmel,ssc-controller = <&ssc0>; + atmel,audio-codec = <&wm8731>; + }; };
Signature · 1 line
1.7.10.4
On 12/08/2013 14:30, Richard Genoud :
Quoted 9 lines
As the sam9x5-wm8731 machine driver has been merged, we have now to add the device tree nodes...
And here they are !(Based on next-20130812)
Tested on at91sam9g35-ek[I didn't add the DT list, as far as there's no new binding, we don't have to bother themi, right ?]
Yep!
On the whole series:
Stacked on top of at91-3.12-dt
Thanks a lot Richard!
Quoted 10 lines
Richard Genoud (4):
ARM: AT91: DTS: sam9x5: add SSC DMA parameters
ARM: AT91: DTS: sam9x5ek: add WM8731 codec
ARM: AT91: DTS: sam9x5ek: enable SSC
ARM: AT91: DTS: sam9x5ek: add sound configurationarch/arm/boot/dts/at91sam9x5.dtsi | 3 +++ arch/arm/boot/dts/at91sam9x5ek.dtsi | 24 ++++++++++++++++++++++++ 2 files changed, 27 insertions(+)
Signature · 1 line
Nicolas Ferre