i915: Update VGA arbiter support for newer devices
Subsystems (2)
PATCH 1/1 i915: Update VGA arbiter support for newer devices
This is intended to add VGA arbiter support for Intel HD graphics on Core processors. The old GMCH registers no longer exist, so even though it appears that i915 participates in VGA arbitration, it doesn't work. On Intel HD graphics we already attempt to disable VGA regions of the device. This makes registering as a VGA client unnecessary since we don't intend to operate differently depending on how many VGA devices are present. We can disable VGA memory regions by clearing a memory enable bit in the VGA MSR. That only leaves VGA IO, which we update the VGA arbiter to know that we don't participate in VGA memory arbitration. We also add a hook on unload to re-enable memory and reinstate VGA memory arbitration.
---
This patch depends on series "vgaarb: Fixes for partial VGA opt-out".
Is HAS_PCH_SPLIT() the right test to identify newer graphics devices?
I've tried not to disturb the old code since I can't test it, but welcome feedback whether we should just remove it. I also don't know what most of i915_disable_vga() is doing and whether it's still relevant.
drivers/gpu/drm/i915/i915_dma.c | 9 ++++++--- drivers/gpu/drm/i915/intel_display.c | 26 ++++++++++++++++++++++++++ 2 files changed, 32 insertions(+), 3 deletions(-)
drivers/gpu/drm/i915/i915_dma.c +6 -3
@@ -1287,9 +1287,12 @@ static int i915_load_modeset_init(struct drm_device *dev)* then we do not take part in VGA arbitration and the * vga_client_register() fails with -ENODEV. */ - ret =vga_client_register (dev->pdev, dev,NULL , i915_vga_set_decode); -if (ret && ret != -ENODEV ) - goto out; +if (!HAS_PCH_SPLIT (dev)) { + ret =vga_client_register (dev->pdev, dev,NULL , + i915_vga_set_decode); +if (ret && ret != -ENODEV ) + goto out; + }intel_register_dsm_handler ();
drivers/gpu/drm/i915/intel_display.c +26 -0
@@ -9519,6 +9519,16 @@ static void i915_disable_vga(struct drm_device *dev)outb (SR01 ,VGA_SR_INDEX ); sr1 =inb (VGA_SR_DATA );outb (sr1 |1 <<5 ,VGA_SR_DATA ); + +/* Disable VGA memory on Intel HD */ +if (HAS_PCH_SPLIT (dev)) { +I915_WRITE8 (VGA_MSR_WRITE , +I915_READ8 (VGA_MSR_READ ) & ~VGA_MSR_MEM_EN ); +vga_set_legacy_decoding (dev->pdev,VGA_RSRC_LEGACY_IO | +VGA_RSRC_NORMAL_IO | +VGA_RSRC_NORMAL_MEM ); + } +vga_put (dev->pdev,VGA_RSRC_LEGACY_IO );udelay (300 );
@@ -9526,6 +9536,20 @@ static void i915_disable_vga(struct drm_device *dev)POSTING_READ (vga_reg); } +static void i915_enable_vga (struct drm_device *dev) +{ +struct drm_i915_private *dev_priv = dev->dev_private; + +/* Disable VGA memory on Intel HD */ +if (HAS_PCH_SPLIT (dev)) { +I915_WRITE8 (VGA_MSR_WRITE , +I915_READ8 (VGA_MSR_READ ) |VGA_MSR_MEM_EN ); +vga_set_legacy_decoding (dev->pdev,VGA_RSRC_LEGACY_MASK | +VGA_RSRC_NORMAL_IO | +VGA_RSRC_NORMAL_MEM ); + } +} +void intel_modeset_init_hw (struct drm_device *dev) {intel_init_power_well (dev);
@@ -9983,6 +10007,8 @@ void intel_modeset_cleanup(struct drm_device *dev)intel_disable_fbc (dev); +i915_enable_vga (dev); +intel_disable_gt_powersave (dev);ironlake_teardown_rc6 (dev);
Dave Airlie
maintainerQuoted 11 lines · Alex Williamson
This is intended to add VGA arbiter support for Intel HD graphics on Core processors. The old GMCH registers no longer exist, so even though it appears that i915 participates in VGA arbitration, it doesn't work. On Intel HD graphics we already attempt to disable VGA regions of the device. This makes registering as a VGA client unnecessary since we don't intend to operate differently depending on how many VGA devices are present. We can disable VGA memory regions by clearing a memory enable bit in the VGA MSR. That only leaves VGA IO, which we update the VGA arbiter to know that we don't participate in VGA memory arbitration. We also add a hook on unload to re-enable memory and reinstate VGA memory arbitration.
I would think there is still a VGA disable bit on the Intel device somewhere, we'd just need
Intel to look in the docs and find it. A bit that can nuke both i/o and cmd regs.
Dave.
Quoted 14 lines · Dave Airlie
Quoted 11 lines · Alex Williamson
This is intended to add VGA arbiter support for Intel HD graphics on Core processors. The old GMCH registers no longer exist, so even though it appears that i915 participates in VGA arbitration, it doesn't work. On Intel HD graphics we already attempt to disable VGA regions of the device. This makes registering as a VGA client unnecessary since we don't intend to operate differently depending on how many VGA devices are present. We can disable VGA memory regions by clearing a memory enable bit in the VGA MSR. That only leaves VGA IO, which we update the VGA arbiter to know that we don't participate in VGA memory arbitration. We also add a hook on unload to re-enable memory and reinstate VGA memory arbitration.
Quoted 4 lines
I would think there is still a VGA disable bit on the Intel device somewhere, we'd just need
Intel to look in the docs and find it. A bit that can nuke both i/o and cmd regs.
The only bit available is in the GGC and is a keyed/locked register that not only disables VGA memory and I/O, but also modifies the class code of the device. Early Core processors didn't lock this, but it's untouchable in newer ones AFAICT. Thanks,
Alex
Quoted 20 lines · Alex Williamson
Quoted 14 lines · Dave Airlie
Quoted 11 lines · Alex Williamson
This is intended to add VGA arbiter support for Intel HD graphics on Core processors. The old GMCH registers no longer exist, so even though it appears that i915 participates in VGA arbitration, it doesn't work. On Intel HD graphics we already attempt to disable VGA regions of the device. This makes registering as a VGA client unnecessary since we don't intend to operate differently depending on how many VGA devices are present. We can disable VGA memory regions by clearing a memory enable bit in the VGA MSR. That only leaves VGA IO, which we update the VGA arbiter to know that we don't participate in VGA memory arbitration. We also add a hook on unload to re-enable memory and reinstate VGA memory arbitration.
Quoted 4 lines
I would think there is still a VGA disable bit on the Intel device somewhere, we'd just need
Intel to look in the docs and find it. A bit that can nuke both i/o and cmd regs.
Quoted 4 lines
The only bit available is in the GGC and is a keyed/locked register that not only disables VGA memory and I/O, but also modifies the class code of the device. Early Core processors didn't lock this, but it's untouchable in newer ones AFAICT. Thanks,
I've not found anything else in the docs. And also we _need_ VGA I/O access to make i915_disable_vga() work. It's not 100% clear whether we really need to poke at the sequencer register in modern hardware, but the docs do still list it as a mandatory step. So even if we were to have a global "disable VGA I/O and mem bit" we'd need to make sure we already disabled VGA eg. after resume when the BIOS had a chance to turn the VGA display back on. I think there were also some BIOSen that turned VGA display back on when closing/opening the laptop lid. Not sure what would even happen with those if totally disabled VGA I/O access. I'm not sure they actually frob with the VGA regs though. Could be they just turn on the VGA display bit in the VGA_CONTROL register.
Signature · 2 lines
Ville Syrjälä Intel OTC
Quoted 26 lines · Ville Syrjälä
Quoted 20 lines · Alex Williamson
Quoted 14 lines · Dave Airlie
Quoted 11 lines · Alex Williamson
This is intended to add VGA arbiter support for Intel HD graphics on Core processors. The old GMCH registers no longer exist, so even though it appears that i915 participates in VGA arbitration, it doesn't work. On Intel HD graphics we already attempt to disable VGA regions of the device. This makes registering as a VGA client unnecessary since we don't intend to operate differently depending on how many VGA devices are present. We can disable VGA memory regions by clearing a memory enable bit in the VGA MSR. That only leaves VGA IO, which we update the VGA arbiter to know that we don't participate in VGA memory arbitration. We also add a hook on unload to re-enable memory and reinstate VGA memory arbitration.
Quoted 4 lines
I would think there is still a VGA disable bit on the Intel device somewhere, we'd just need
Intel to look in the docs and find it. A bit that can nuke both i/o and cmd regs.Quoted 4 lines
The only bit available is in the GGC and is a keyed/locked register that not only disables VGA memory and I/O, but also modifies the class code of the device. Early Core processors didn't lock this, but it's untouchable in newer ones AFAICT. Thanks,
Quoted 12 lines
I've not found anything else in the docs. And also we _need_ VGA I/O access to make
i915_disable_vga()work. It's not 100% clear whether we really need to poke at the sequencer register in modern hardware, but the docs do still list it as a mandatory step. So even if we were to have a global "disable VGA I/O and mem bit" we'd need to make sure we already disabled VGA eg. after resume when the BIOS had a chance to turn the VGA display back on. I think there were also some BIOSen that turned VGA display back on when closing/opening the laptop lid. Not sure what would even happen with those if totally disabled VGA I/O access. I'm not sure they actually frob with the VGA regs though. Could be they just turn on the VGA display bit in theVGA_CONTROLregister.
Hmm, it appears the MSR write isn't fully disabling VGA memory space. When the VBIOS for the PEG graphics is run in the guest, I get some corruption of the IGD frame buffer. If I manually disable PCI memory in the command register, this doesn't happen. I also get some strange artifacts on the PEG display that don't happen when PCI memory is disabled. Should that MSR bit give us the whole a_0000-b_ffff range? Thanks,
Alex
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 40 lines · Alex Williamson
Quoted 26 lines · Ville Syrjälä
Quoted 20 lines · Alex Williamson
Quoted 14 lines · Dave Airlie
Quoted 11 lines · Alex Williamson
This is intended to add VGA arbiter support for Intel HD graphics on Core processors. The old GMCH registers no longer exist, so even though it appears that i915 participates in VGA arbitration, it doesn't work. On Intel HD graphics we already attempt to disable VGA regions of the device. This makes registering as a VGA client unnecessary since we don't intend to operate differently depending on how many VGA devices are present. We can disable VGA memory regions by clearing a memory enable bit in the VGA MSR. That only leaves VGA IO, which we update the VGA arbiter to know that we don't participate in VGA memory arbitration. We also add a hook on unload to re-enable memory and reinstate VGA memory arbitration.
Quoted 4 lines
I would think there is still a VGA disable bit on the Intel device somewhere, we'd just need
Intel to look in the docs and find it. A bit that can nuke both i/o and cmd regs.Quoted 4 lines
The only bit available is in the GGC and is a keyed/locked register that not only disables VGA memory and I/O, but also modifies the class code of the device. Early Core processors didn't lock this, but it's untouchable in newer ones AFAICT. Thanks,
Quoted 12 lines
I've not found anything else in the docs. And also we _need_ VGA I/O access to make
i915_disable_vga()work. It's not 100% clear whether we really need to poke at the sequencer register in modern hardware, but the docs do still list it as a mandatory step. So even if we were to have a global "disable VGA I/O and mem bit" we'd need to make sure we already disabled VGA eg. after resume when the BIOS had a chance to turn the VGA display back on. I think there were also some BIOSen that turned VGA display back on when closing/opening the laptop lid. Not sure what would even happen with those if totally disabled VGA I/O access. I'm not sure they actually frob with the VGA regs though. Could be they just turn on the VGA display bit in theVGA_CONTROLregister.
Quoted 6 lines
Hmm, it appears the MSR write isn't fully disabling VGA memory space. When the VBIOS for the PEG graphics is run in the guest, I get some corruption of the IGD frame buffer. If I manually disable PCI memory in the command register, this doesn't happen. I also get some strange artifacts on the PEG display that don't happen when PCI memory is disabled. Should that MSR bit give us the whole a_0000-b_ffff range?
Perhaps. It does that on some old graphics cards I've played with, but frankly I have no idea what it does on our hardware.
I'm trying to find out though. If and when I get an answer I'll let you know.
Signature · 2 lines
Ville Syrjälä Intel OTC
Quoted 48 lines · Ville Syrjälä
Quoted 40 lines · Alex Williamson
Quoted 26 lines · Ville Syrjälä
Quoted 20 lines · Alex Williamson
Quoted 14 lines · Dave Airlie
Quoted 11 lines · Alex Williamson
This is intended to add VGA arbiter support for Intel HD graphics on Core processors. The old GMCH registers no longer exist, so even though it appears that i915 participates in VGA arbitration, it doesn't work. On Intel HD graphics we already attempt to disable VGA regions of the device. This makes registering as a VGA client unnecessary since we don't intend to operate differently depending on how many VGA devices are present. We can disable VGA memory regions by clearing a memory enable bit in the VGA MSR. That only leaves VGA IO, which we update the VGA arbiter to know that we don't participate in VGA memory arbitration. We also add a hook on unload to re-enable memory and reinstate VGA memory arbitration.
Quoted 4 lines
I would think there is still a VGA disable bit on the Intel device somewhere, we'd just need
Intel to look in the docs and find it. A bit that can nuke both i/o and cmd regs.Quoted 4 lines
The only bit available is in the GGC and is a keyed/locked register that not only disables VGA memory and I/O, but also modifies the class code of the device. Early Core processors didn't lock this, but it's untouchable in newer ones AFAICT. Thanks,
Quoted 12 lines
I've not found anything else in the docs. And also we _need_ VGA I/O access to make
i915_disable_vga()work. It's not 100% clear whether we really need to poke at the sequencer register in modern hardware, but the docs do still list it as a mandatory step. So even if we were to have a global "disable VGA I/O and mem bit" we'd need to make sure we already disabled VGA eg. after resume when the BIOS had a chance to turn the VGA display back on. I think there were also some BIOSen that turned VGA display back on when closing/opening the laptop lid. Not sure what would even happen with those if totally disabled VGA I/O access. I'm not sure they actually frob with the VGA regs though. Could be they just turn on the VGA display bit in theVGA_CONTROLregister.Quoted 6 lines
Hmm, it appears the MSR write isn't fully disabling VGA memory space. When the VBIOS for the PEG graphics is run in the guest, I get some corruption of the IGD frame buffer. If I manually disable PCI memory in the command register, this doesn't happen. I also get some strange artifacts on the PEG display that don't happen when PCI memory is disabled. Should that MSR bit give us the whole a_0000-b_ffff range?
Quoted 5 lines
Perhaps. It does that on some old graphics cards I've played with, but frankly I have no idea what it does on our hardware.
I'm trying to find out though. If and when I get an answer I'll let you know.
So the answer I basically got is that MSR is the only option here when the GMCH register can't be used. Supposedly it should work too, but I felt that I didn't get a 100% definite answer on that subject.
I tried it a bit on an IVB machine and PCI and PCIe Matrox G550 cards, and for me it does seem to work. In the G550 PCIe case there's an extra PCIe-PCI bridge on the card, and and in the G550 PCI case there's a PCI-PCI bridge on the card and a PCIe-PCI bridge on the motherboard. I don't have any native PCIe graphics cards on me to test the no extra bridges case.
Based on a bit of manual register/memory banging it looks like the IGD will decode the access when MSR[1]=1, and won't when MSR[1]=0. Same was true for PCI_COMMAND[0] in case of VGA I/O. If those bits are disabled for IGD, the accesses get to the external card. If neither claims it, I just get 0xff back and writes are ignored.
Curiously I didn't see any problems when I configured both graphics devices and bridges to decode/forward VGA resources. The IGD was always the one to answer and the data didn't seem corrupted. Not sure why that is. Maybe I just got lucky or something.
My tests weren't very thorough however, so I may have missed something.
Signature · 2 lines
Ville Syrjälä Intel OTC
Quoted 52 lines · Ville Syrjälä
Quoted 51 lines · Ville Syrjälä
Quoted 40 lines · Alex Williamson
Quoted 26 lines · Ville Syrjälä
Quoted 20 lines · Alex Williamson
Quoted 14 lines · Dave Airlie
Quoted 11 lines · Alex Williamson
This is intended to add VGA arbiter support for Intel HD graphics on Core processors. The old GMCH registers no longer exist, so even though it appears that i915 participates in VGA arbitration, it doesn't work. On Intel HD graphics we already attempt to disable VGA regions of the device. This makes registering as a VGA client unnecessary since we don't intend to operate differently depending on how many VGA devices are present. We can disable VGA memory regions by clearing a memory enable bit in the VGA MSR. That only leaves VGA IO, which we update the VGA arbiter to know that we don't participate in VGA memory arbitration. We also add a hook on unload to re-enable memory and reinstate VGA memory arbitration.
Quoted 4 lines
I would think there is still a VGA disable bit on the Intel device somewhere, we'd just need
Intel to look in the docs and find it. A bit that can nuke both i/o and cmd regs.Quoted 4 lines
The only bit available is in the GGC and is a keyed/locked register that not only disables VGA memory and I/O, but also modifies the class code of the device. Early Core processors didn't lock this, but it's untouchable in newer ones AFAICT. Thanks,
Quoted 12 lines
I've not found anything else in the docs. And also we _need_ VGA I/O access to make
i915_disable_vga()work. It's not 100% clear whether we really need to poke at the sequencer register in modern hardware, but the docs do still list it as a mandatory step. So even if we were to have a global "disable VGA I/O and mem bit" we'd need to make sure we already disabled VGA eg. after resume when the BIOS had a chance to turn the VGA display back on. I think there were also some BIOSen that turned VGA display back on when closing/opening the laptop lid. Not sure what would even happen with those if totally disabled VGA I/O access. I'm not sure they actually frob with the VGA regs though. Could be they just turn on the VGA display bit in theVGA_CONTROLregister.Quoted 6 lines
Hmm, it appears the MSR write isn't fully disabling VGA memory space. When the VBIOS for the PEG graphics is run in the guest, I get some corruption of the IGD frame buffer. If I manually disable PCI memory in the command register, this doesn't happen. I also get some strange artifacts on the PEG display that don't happen when PCI memory is disabled. Should that MSR bit give us the whole a_0000-b_ffff range?
Perhaps. It does that on some old graphics cards I've played with, but frankly I have no idea what it does on our hardware.
Quoted 6 lines
Quoted 2 lines
I'm trying to find out though. If and when I get an answer I'll let you know.
So the answer I basically got is that MSR is the only option here when the GMCH register can't be used. Supposedly it should work too, but I felt that I didn't get a 100% definite answer on that subject.
I can imagine that the GMCH could be modified if we knew where the bit was that's locking it. I can't find that in the spec though and I assume that's intentional.
Quoted 13 lines
I tried it a bit on an IVB machine and PCI and PCIe Matrox G550 cards, and for me it does seem to work. In the G550 PCIe case there's an extra PCIe-PCI bridge on the card, and and in the G550 PCI case there's a PCI-PCI bridge on the card and a PCIe-PCI bridge on the motherboard. I don't have any native PCIe graphics cards on me to test the no extra bridges case.
Based on a bit of manual register/memory banging it looks like the IGD will decode the access when MSR[1]=1, and won't when MSR[1]=0. Same was true for PCI_COMMAND[0] in case of VGA I/O. If those bits are disabled for IGD, the accesses get to the external card. If neither claims it, I just get
0xffback and writes are ignored.
Quoted 6 lines
Curiously I didn't see any problems when I configured both graphics devices and bridges to decode/forward VGA resources. The IGD was always the one to answer and the data didn't seem corrupted. Not sure why that is. Maybe I just got lucky or something.
My tests weren't very thorough however, so I may have missed something.
Thanks for checking Ville. I wrote a test program myself to blast VGA space through /dev/mem. I agree, it sure seems like the MSR bit is doing it's job. That makes me suspect that I'm not actually getting the bit cleared or that it's being re-enabled somewhere else. I'll do some more digging to make sure the MSR bit is actually cleared on IGD before I start the VM. Thanks!
Alex
Quoted 82 lines · Alex Williamson
Quoted 52 lines · Ville Syrjälä
Quoted 51 lines · Ville Syrjälä
Quoted 40 lines · Alex Williamson
Quoted 26 lines · Ville Syrjälä
Quoted 20 lines · Alex Williamson
Quoted 14 lines · Dave Airlie
Quoted 11 lines · Alex Williamson
This is intended to add VGA arbiter support for Intel HD graphics on Core processors. The old GMCH registers no longer exist, so even though it appears that i915 participates in VGA arbitration, it doesn't work. On Intel HD graphics we already attempt to disable VGA regions of the device. This makes registering as a VGA client unnecessary since we don't intend to operate differently depending on how many VGA devices are present. We can disable VGA memory regions by clearing a memory enable bit in the VGA MSR. That only leaves VGA IO, which we update the VGA arbiter to know that we don't participate in VGA memory arbitration. We also add a hook on unload to re-enable memory and reinstate VGA memory arbitration.
Quoted 4 lines
I would think there is still a VGA disable bit on the Intel device somewhere, we'd just need
Intel to look in the docs and find it. A bit that can nuke both i/o and cmd regs.Quoted 4 lines
The only bit available is in the GGC and is a keyed/locked register that not only disables VGA memory and I/O, but also modifies the class code of the device. Early Core processors didn't lock this, but it's untouchable in newer ones AFAICT. Thanks,
Quoted 12 lines
I've not found anything else in the docs. And also we _need_ VGA I/O access to make
i915_disable_vga()work. It's not 100% clear whether we really need to poke at the sequencer register in modern hardware, but the docs do still list it as a mandatory step. So even if we were to have a global "disable VGA I/O and mem bit" we'd need to make sure we already disabled VGA eg. after resume when the BIOS had a chance to turn the VGA display back on. I think there were also some BIOSen that turned VGA display back on when closing/opening the laptop lid. Not sure what would even happen with those if totally disabled VGA I/O access. I'm not sure they actually frob with the VGA regs though. Could be they just turn on the VGA display bit in theVGA_CONTROLregister.Quoted 6 lines
Hmm, it appears the MSR write isn't fully disabling VGA memory space. When the VBIOS for the PEG graphics is run in the guest, I get some corruption of the IGD frame buffer. If I manually disable PCI memory in the command register, this doesn't happen. I also get some strange artifacts on the PEG display that don't happen when PCI memory is disabled. Should that MSR bit give us the whole a_0000-b_ffff range?
Perhaps. It does that on some old graphics cards I've played with, but frankly I have no idea what it does on our hardware.
Quoted 6 lines
Quoted 2 lines
I'm trying to find out though. If and when I get an answer I'll let you know.
So the answer I basically got is that MSR is the only option here when the GMCH register can't be used. Supposedly it should work too, but I felt that I didn't get a 100% definite answer on that subject.
I can imagine that the GMCH could be modified if we knew where the bit was that's locking it. I can't find that in the spec though and I assume that's intentional.
Quoted 18 lines
I tried it a bit on an IVB machine and PCI and PCIe Matrox G550 cards, and for me it does seem to work. In the G550 PCIe case there's an extra PCIe-PCI bridge on the card, and and in the G550 PCI case there's a PCI-PCI bridge on the card and a PCIe-PCI bridge on the motherboard. I don't have any native PCIe graphics cards on me to test the no extra bridges case.
Based on a bit of manual register/memory banging it looks like the IGD will decode the access when MSR[1]=1, and won't when MSR[1]=0. Same was true for PCI_COMMAND[0] in case of VGA I/O. If those bits are disabled for IGD, the accesses get to the external card. If neither claims it, I just get
0xffback and writes are ignored.Curiously I didn't see any problems when I configured both graphics devices and bridges to decode/forward VGA resources. The IGD was always the one to answer and the data didn't seem corrupted. Not sure why that is. Maybe I just got lucky or something.
Quoted 8 lines
Quoted 1 line
My tests weren't very thorough however, so I may have missed something.
Thanks for checking Ville. I wrote a test program myself to blast VGA space through
/dev/mem. I agree, it sure seems like the MSR bit is doing it's job. That makes me suspect that I'm not actually getting the bit cleared or that it's being re-enabled somewhere else. I'll do some more digging to make sure the MSR bit is actually cleared on IGD before I start the VM.
Yep, something is broken there. At the point where I try to read and set the MSR, I'm reading 0x0. The device has I/O port enabled in the command register at that point, so I don't know what's wrong just yet. By the time I'm booted to an fb login prompt it reads 0x67, so I'm obviously being unsuccessful in clearing that bit. Thanks,
Alex