Skip to contentSkip to conversation

ARM: dts: imx6q-sabrelite: Put the nodes in alphabetical order

PATCH New Fabio Estevam 2 participants 3 messages Aug 28, 2013 – Aug 29, 2013

Subsystems (2)
Device tree bindings Arm i.MX and Layerscape
lore
Share & tools
lore

Fabio Estevam

author reviewer
#0 lore raw

PATCH 1/2 ARM: dts: imx6q-sabrelite: Put the nodes in alphabetical order

From: Fabio Estevam <[email protected]>

Put the nodes in alphabetical order so that further node additions can be better organized.

Signed-off-by Fabio Estevam <[email protected]>
---
 arch/arm/boot/dts/imx6q-sabrelite.dts | 78 +++++++++++++++++------------------
 1 file changed, 39 insertions(+), 39 deletions(-)
arch/arm/boot/dts/imx6q-sabrelite.dts +39 -39
index 3530280..b96a72e 100644
@@ -65,8 +65,10 @@
 	};
 };
 
-&sata {
+&audmux {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux_1>;
 };
 
 &ecspi1 {

@@ -83,11 +85,29 @@
 	};
 };
 
-&ssi1 {
-	fsl,mode = "i2s-slave";
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet_1>;
+	phy-mode = "rgmii";
+	phy-reset-gpios = <&gpio3 23 0>;
 	status = "okay";
 };
 
+&i2c1 {
+	status = "okay";
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1_1>;
+
+	codec: sgtl5000 at 0a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		clocks = <&clks 201>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_3p3v>;
+	};
+};
+
 &iomuxc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;

@@ -108,23 +128,30 @@
 	};
 };
 
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg_1>;
-	disable-over-current;
+&sata {
+	status = "okay";
+};
+
+&ssi1 {
+	fsl,mode = "i2s-slave";
+	status = "okay";
+};
+
+&uart2 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2_1>;
 };
 
 &usbh1 {
 	status = "okay";
 };
 
-&fec {
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet_1>;
-	phy-mode = "rgmii";
-	phy-reset-gpios = <&gpio3 23 0>;
+	pinctrl-0 = <&pinctrl_usbotg_1>;
+	disable-over-current;
 	status = "okay";
 };
 

@@ -145,30 +172,3 @@
 	vmmc-supply = <&reg_3p3v>;
 	status = "okay";
 };
-
-&audmux {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux_1>;
-};
-
-&uart2 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2_1>;
-};
-
-&i2c1 {
-	status = "okay";
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1_1>;
-
-	codec: sgtl5000 at 0a {
-		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
-		clocks = <&clks 201>;
-		VDDA-supply = <&reg_2p5v>;
-		VDDIO-supply = <&reg_3p3v>;
-	};
-};
Signature · 1 line
1.8.1.2
author reviewer
#1 lore raw

PATCH 2/2 ARM: dts: imx6q-sabrelite: Add LVDS support

From: Fabio Estevam <[email protected]>

imx6q-sabrelite board can be connected to a 1024x768 Hannstar LVDS panel.

Add support for it.

Signed-off-by Fabio Estevam <[email protected]>
---
 arch/arm/boot/dts/imx6q-sabrelite.dts | 25 +++++++++++++++++++++++++
 1 file changed, 25 insertions(+)
arch/arm/boot/dts/imx6q-sabrelite.dts +25 -0
index b96a72e..e1c1777 100644
@@ -128,6 +128,31 @@
 	};
 };
 
+&ldb {
+	status = "okay";
+
+	lvds-channel at 0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <18>;
+		status = "okay";
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: hsd100pxn1 {
+				clock-frequency = <65000000>;
+				hactive = <1024>;
+				vactive = <768>;
+				hback-porch = <220>;
+				hfront-porch = <40>;
+				vback-porch = <21>;
+				vfront-porch = <7>;
+				hsync-len = <60>;
+				vsync-len = <10>;
+			};
+		};
+	};
+};
+
 &sata {
 	status = "okay";
 };
Signature · 1 line
1.8.1.2