Skip to contentSkip to conversation

Add PCIe support for i.MX6q

PATCH Superseded Sean Cross 3 participants 11 messages Sep 12, 2013

Subsystems (9)

v3 of 6 Superseded Latest is v6 →

lore
Share & tools
lore

Sean Cross

author
#0 lore raw

v3 cover Add PCIe support for i.MX6q

This patchset adds support for the PCI Express port present on the i.MX6 SoC. The port is based on Synopsis Designware IP with a custom PHY.

Changes since v2:
- Reworked source file with Sascha Hauer's suggestions

Changes since v1:
- Use the Designware controller code for BAR initialization

Sean Cross (3):
ARM: imx: Add LVDS general-purpose clocks to i.MX6Q
ARM: imx6q: Add PCIe bits to GPR syscon definition
PCI: imx6: Add support for i.MX6 PCIe controller

 .../devicetree/bindings/clock/imx6q-clock.txt      |    4 +
 .../devicetree/bindings/pci/designware-pcie.txt    |    5 +
 arch/arm/boot/dts/imx6qdl.dtsi                     |   18 +
 arch/arm/mach-imx/Kconfig                          |    2 +
 arch/arm/mach-imx/clk-imx6q.c                      |   21 +-
 drivers/pci/host/Kconfig                           |    6 +
 drivers/pci/host/Makefile                          |    1 +
 drivers/pci/host/pci-imx6.c                        |  549 ++++++++++++++++++++
 include/linux/mfd/syscon/imx6q-iomuxc-gpr.h        |    8 +
 9 files changed, 613 insertions(+), 1 deletion(-)
 create mode 100644 drivers/pci/host/pci-imx6.c
Signature · 1 line
1.7.9.5
author
#1 lore raw

PATCH v3 1/3 ARM: imx: Add LVDS general-purpose clocks to i.MX6Q

The i.MX6 has two general-purpose LVDS clocks that can be driven from a variety of sources. This patch adds a mux and a gate for both of these clocks.

---
 .../devicetree/bindings/clock/imx6q-clock.txt      |    4 ++++
 arch/arm/mach-imx/clk-imx6q.c                      |   21 +++++++++++++++++++-
 2 files changed, 24 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/clock/imx6q-clock.txt +4 -0
index 5a90a72..35e82c7 100644
@@ -215,6 +215,10 @@ clocks and IDs.
 	cko2      		200
 	cko      		201
 	vdoa      		202
+	lvds1_sel		203
+	lvds2_sel		204
+	lvds1_gate		205
+	lvds2_gate		206
 
 Examples:
 
arch/arm/mach-imx/clk-imx6q.c +20 -1
index 9181a24..679d49a 100644
@@ -217,6 +217,16 @@ static const char *cko2_sels[] = {
 	"uart_serial", "spdif", "asrc", "hsi_tx",
 };
 static const char *cko_sels[] = { "cko1", "cko2", };
+static const char *lvds1_sels[] = {
+	"dummy", "dummy", "dummy", "dummy", "dummy", "dummy",
+	"pll4_audio", "pll5_video", "pll8_mlb", "enet_ref",
+	"pcie_ref", "sata_ref",
+};
+static const char *lvds2_sels[] = {
+	"dummy", "dummy", "dummy", "dummy", "dummy", "dummy",
+	"pll4_audio", "pll5_video", "pll8_mlb", "enet_ref",
+	"pcie_ref", "sata_ref",
+};
 
 enum mx6q_clks {
 	dummy, ckil, ckih, osc, pll2_pfd0_352m, pll2_pfd1_594m, pll2_pfd2_396m,
@@ -251,7 +261,8 @@ enum mx6q_clks {
 	ssi2_ipg, ssi3_ipg, rom, usbphy1, usbphy2, ldb_di0_div_3_5, ldb_di1_div_3_5,
 	sata_ref, sata_ref_100m, pcie_ref, pcie_ref_125m, enet_ref, usbphy1_gate,
 	usbphy2_gate, pll4_post_div, pll5_post_div, pll5_video_div, eim_slow,
-	spdif, cko2_sel, cko2_podf, cko2, cko, vdoa, clk_max
+	spdif, cko2_sel, cko2_podf, cko2, cko, vdoa,
+	lvds1_sel, lvds2_sel, lvds1_gate, lvds2_gate, clk_max
 };
 
 static struct clk *clk[clk_max];
@@ -342,6 +353,12 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 			base + 0xe0, 0, 2, 0, clk_enet_ref_table,
 			&imx_ccm_lock);
 
+	clk[lvds1_sel] = imx_clk_mux("lvds1_sel", base + 0x160, 0, 5, lvds1_sels,         ARRAY_SIZE(lvds1_sels));
+	clk[lvds2_sel] = imx_clk_mux("lvds2_sel", base + 0x160, 5, 5, lvds2_sels,         ARRAY_SIZE(lvds2_sels));
+
+	clk[lvds1_gate] = imx_clk_gate("lvds1_gate", "dummy", base + 0x160, 10);
+	clk[lvds2_gate] = imx_clk_gate("lvds2_gate", "dummy", base + 0x160, 11);
+
 	/*                                name              parent_name        reg       idx */
 	clk[pll2_pfd0_352m] = imx_clk_pfd("pll2_pfd0_352m", "pll2_bus",     base + 0x100, 0);
 	clk[pll2_pfd1_594m] = imx_clk_pfd("pll2_pfd1_594m", "pll2_bus",     base + 0x100, 1);
@@ -569,6 +586,8 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
 	clk_register_clkdev(clk[cko1_sel], "cko1_sel", NULL);
 	clk_register_clkdev(clk[ahb], "ahb", NULL);
 	clk_register_clkdev(clk[cko1], "cko1", NULL);
+	clk_register_clkdev(clk[lvds1_gate], "lvds1_gate", NULL);
+	clk_register_clkdev(clk[lvds2_gate], "lvds2_gate", NULL);
 	clk_register_clkdev(clk[arm], NULL, "cpu0");
 	clk_register_clkdev(clk[pll4_post_div], "pll4_post_div", NULL);
 	clk_register_clkdev(clk[pll4_audio], "pll4_audio", NULL);
Signature · 1 line
1.7.9.5
author
#2 lore raw

PATCH v3 2/3 ARM: imx6q: Add PCIe bits to GPR syscon definition

In reply to Sean Cross

PCIe requires additional bits be defined for GPR8 and GPR12.

---
 include/linux/mfd/syscon/imx6q-iomuxc-gpr.h |    8 ++++++++
 1 file changed, 8 insertions(+)
include/linux/mfd/syscon/imx6q-iomuxc-gpr.h +8 -0
index b6bdcd6..1bf1fe9 100644
@@ -241,6 +241,12 @@
 
 #define IMX6Q_GPR5_L2_CLK_STOP			BIT(8)
 
+#define IMX6Q_GPR8_TX_DEEMPH_GEN1		(0x3F << 0)
+#define IMX6Q_GPR8_TX_DEEMPH_GEN2_3P5DB		(0x3F << 6)
+#define IMX6Q_GPR8_TX_DEEMPH_GEN2_6DB		(0x3F << 12)
+#define IMX6Q_GPR8_TX_SWING_FULL		(0x7F << 18)
+#define IMX6Q_GPR8_TX_SWING_LOW			(0x7F << 25)
+
 #define IMX6Q_GPR9_TZASC2_BYP			BIT(1)
 #define IMX6Q_GPR9_TZASC1_BYP			BIT(0)
 
@@ -273,7 +279,9 @@
 #define IMX6Q_GPR12_ARMP_AHB_CLK_EN		BIT(26)
 #define IMX6Q_GPR12_ARMP_ATB_CLK_EN		BIT(25)
 #define IMX6Q_GPR12_ARMP_APB_CLK_EN		BIT(24)
+#define IMX6Q_GPR12_DEVICE_TYPE			(0xF << 12)
 #define IMX6Q_GPR12_PCIE_CTL_2			BIT(10)
+#define IMX6Q_GPR12_LOS_LEVEL			(0x1F << 4)
 
 #define IMX6Q_GPR13_SDMA_STOP_REQ		BIT(30)
 #define IMX6Q_GPR13_CAN2_STOP_REQ		BIT(29)
Signature · 1 line
1.7.9.5
author
#3 lore raw

PATCH v3 3/3 PCI: imx6: Add support for i.MX6 PCIe controller

In reply to Sean Cross

Add support for the PCIe port present on the i.MX6 family of controllers. These use the Synopsis Designware core tied to their own PHY.

---
 .../devicetree/bindings/pci/designware-pcie.txt    |    5 +
 arch/arm/boot/dts/imx6qdl.dtsi                     |   18 +
 arch/arm/mach-imx/Kconfig                          |    2 +
 drivers/pci/host/Kconfig                           |    6 +
 drivers/pci/host/Makefile                          |    1 +
 drivers/pci/host/pci-imx6.c                        |  549 ++++++++++++++++++++
 6 files changed, 581 insertions(+)
 create mode 100644 drivers/pci/host/pci-imx6.c
Documentation/devicetree/bindings/pci/designware-pcie.txt +5 -0
index eabcb4b..41d8419 100644
@@ -21,6 +21,11 @@ Required properties:
 - num-lanes: number of lanes to use
 - reset-gpio: gpio pin number of power good signal
 
+Optional properties for fsl,imx6-pcie
+- power-on-gpio: gpio pin number of power-enable signal
+- wake-up-gpio: gpio pin number of incoming wakeup signal
+- disable-gpio: gpio pin number of outgoing rfkill/endpoint disable signal
+
 Example:
 
 SoC specific DT Entry:
arch/arm/boot/dts/imx6qdl.dtsi +18 -0
index ccd55c2..ae51f60 100644
@@ -116,6 +116,24 @@
 			arm,data-latency = <4 2 3>;
 		};
 
+		pcie: pcie at 0x01000000 {
+			compatible = "fsl,imx6-pcie", "snps,dw-pcie";
+			reg = <0x01ffc000 0x4000>; /* DBI */
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x000fc000   /* configuration space */
+				  0x81000000 0 0          0x01000000 0 0x00100000   /* downstream I/O */
+				  0x82000000 0 0x01100000 0x01100000 0 0x00e00000>; /* non-prefetchable memory */
+
+			num-lanes = <1>;
+			interrupts = <0 123 0x04>;
+			clocks = <&clks 186>, <&clks 189>, <&clks 203>, <&clks 205>, <&clks 144>;
+			clock-names = "sata_ref", "pcie_ref_125m", "lvds1_sel", "lvds1_gate", "pcie_axi";
+			status = "disabled";
+		};
+
 		pmu {
 			compatible = "arm,cortex-a9-pmu";
 			interrupts = <0 94 0x04>;
arch/arm/mach-imx/Kconfig +2 -0
index 29a8af6..e6ac281 100644
@@ -801,6 +801,8 @@ config SOC_IMX6Q
 	select HAVE_IMX_SRC
 	select HAVE_SMP
 	select MFD_SYSCON
+	select MIGHT_HAVE_PCI
+	select PCI_DOMAINS if PCI
 	select PINCTRL
 	select PINCTRL_IMX6Q
 	select PL310_ERRATA_588369 if CACHE_PL310
drivers/pci/host/Kconfig +6 -0
index 3d95048..efa24d9 100644
@@ -15,6 +15,12 @@ config PCI_EXYNOS
 	select PCIEPORTBUS
 	select PCIE_DW
 
+config PCI_IMX6
+	bool "Freescale i.MX6 PCIe controller"
+	depends on SOC_IMX6Q
+	select PCIEPORTBUS
+	select PCIE_DW
+
 config PCI_TEGRA
 	bool "NVIDIA Tegra PCIe controller"
 	depends on ARCH_TEGRA
drivers/pci/host/Makefile +1 -0
index c9a997b..287d6a0 100644
@@ -1,4 +1,5 @@
 obj-$(CONFIG_PCIE_DW) += pcie-designware.o
 obj-$(CONFIG_PCI_EXYNOS) += pci-exynos.o
+obj-$(CONFIG_PCI_IMX6) += pci-imx6.o
 obj-$(CONFIG_PCI_MVEBU) += pci-mvebu.o
 obj-$(CONFIG_PCI_TEGRA) += pci-tegra.o
drivers/pci/host/pci-imx6.c new file +549 -0

549 lines not on this page · raw message

Signature · 1 line
1.7.9.5
maintainer
#4 lore raw

PATCH v3 3/3 PCI: imx6: Add support for i.MX6 PCIe controller

Sean,

Several more comments.

Shawn,

A question about a clk_set_parent inside.

drivers/pci/host/pci-imx6.c line 49

Quoted 3 lines · Sean Cross
drivers/pci/host/pci-imx6.c new file +3 -0
+
+#define IMX6_ENTER_RESET 0
+#define IMX6_EXIT_RESET 1

These are unused

drivers/pci/host/pci-imx6.c line 52

Quoted 3 lines
drivers/pci/host/pci-imx6.c new file +3 -0
+
+#define IMX6_POWER_OFF 0
+#define IMX6_POWER_ON 1

unused aswell

drivers/pci/host/pci-imx6.c line 87

Quoted 11 lines
drivers/pci/host/pci-imx6.c new file +11 -0
+static int pcie_phy_poll_ack(void __iomem *dbi_base, int max_iterations,
+			     int exp_val)
+{
+	u32 val;
+	u32 wait_counter = 0;
+
+	do {
+		val = readl(dbi_base + PCIE_PHY_STAT);
+		val = (val >> PCIE_PHY_STAT_ACK_LOC) & 0x1;
+		wait_counter++;
+	} while ((wait_counter < max_iterations) && (val != exp_val));

may_iterations is never something else than 100 so you should drop the argument.
Also I would prefer a real timeout here rather than a counter.

drivers/pci/host/pci-imx6.c line 90

Quoted 3 lines
drivers/pci/host/pci-imx6.c new file +3 -0
+
+	if (val != exp_val)
+		return -1;

By saying "A negative error value" I actually meant one of include/uapi/asm-generic/errno*

Quoted 7 lines
drivers/pci/host/pci-imx6.c new file +7 -0
+static int pcie_phy_write(void __iomem *dbi_base, int addr, int data)
+{
+	u32 var;
+
+	/* write addr */
+	/* cap addr */
+	if (pcie_phy_wait_ack(dbi_base, addr))

drivers/pci/host/pci-imx6.c line 160

Quoted 10 lines
drivers/pci/host/pci-imx6.c new file +10 -0
+		return -1;
+
+	var = data << PCIE_PHY_CTRL_DATA_LOC;
+	writel(var, dbi_base + PCIE_PHY_CTRL);
+
+	/* capture data */
+	var |= (0x1 << PCIE_PHY_CTRL_CAP_DAT_LOC);
+	writel(var, dbi_base + PCIE_PHY_CTRL);
+
+	/* wait for ack */

Drop this comment.

Quoted 3 lines
drivers/pci/host/pci-imx6.c new file +3 -0
+	if (pcie_phy_poll_ack(dbi_base, 100, 1))
+		return -1;
+

...

drivers/pci/host/pci-imx6.c line 216

Quoted 7 lines
drivers/pci/host/pci-imx6.c new file +7 -0
+static int imx6_pcie_deassert_core_reset(struct pcie_port *pp)
+{
+	int ret;
+	struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
+
+	if (imx6_pcie->power_on_gpio >= 0)
+		gpio_set_value(imx6_pcie->power_on_gpio, IMX6_POWER_ON);

in probe you used gpio_is_valid(). Why not here?

drivers/pci/host/pci-imx6.c line 227

Quoted 11 lines
drivers/pci/host/pci-imx6.c new file +11 -0
+
+	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+			IMX6Q_GPR1_PCIE_TEST_PD, 0 << 18);
+	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+			IMX6Q_GPR1_PCIE_REF_CLK_EN, 1 << 16);
+
+	ret = clk_set_parent(imx6_pcie->lvds1_sel, imx6_pcie->sata_ref);
+	if (ret) {
+		dev_err(pp->dev, "unable to set lvds1_gate parent\n");
+		goto err_set_parent;
+	}

I'm unsure this should be done here. Shawn, should we do this in SoC code?

Quoted 16 lines
drivers/pci/host/pci-imx6.c new file +16 -0
+
+	ret = clk_prepare_enable(imx6_pcie->pcie_ref_125m);
+	if (ret) {
+		dev_err(pp->dev, "unable to enable pcie_ref_125m\n");
+		goto err_pcie_ref;
+	}
+
+	ret = clk_prepare_enable(imx6_pcie->lvds1_gate);
+	if (ret) {
+		dev_err(pp->dev, "unable to enable lvds1_gate\n");
+		goto err_lvds1_gate;
+	}
+
+	ret = clk_prepare_enable(imx6_pcie->pcie_axi);
+	if (ret) {
+		dev_err(pp->dev, "unable to enable pcie_axi\n");

drivers/pci/host/pci-imx6.c line 253

Quoted 10 lines
drivers/pci/host/pci-imx6.c new file +10 -0
+		goto err_pcie_axi;
+	}
+
+	/* allow the clocks to stabilize */
+	usleep_range(100, 200);
+
+	return 0;
+
+err_pcie_axi:
+	clk_disable(imx6_pcie->lvds1_gate);

The counterpart of clk_prepare_enable is clk_disable_unprepare.

drivers/pci/host/pci-imx6.c line 315

Quoted 5 lines
drivers/pci/host/pci-imx6.c new file +5 -0
+			return;
+		}
+	}
+
+	return;

unnecessary return

drivers/pci/host/pci-imx6.c line 438

Quoted 6 lines
drivers/pci/host/pci-imx6.c new file +6 -0
+
+	imx6_pcie->power_on_gpio = of_get_named_gpio(np, "power-on-gpio", 0);
+	if (gpio_is_valid(imx6_pcie->power_on_gpio))
+		devm_gpio_request_one(&pdev->dev, imx6_pcie->power_on_gpio,
+				    GPIOF_OUT_INIT_LOW,
+				    "PCIe power enable");

devm_gpio_request_one can still fail.

Quoted 19 lines
drivers/pci/host/pci-imx6.c new file +19 -0
+
+	imx6_pcie->wake_up_gpio = of_get_named_gpio(np, "wake-up-gpio", 0);
+	if (gpio_is_valid(imx6_pcie->wake_up_gpio))
+		devm_gpio_request_one(&pdev->dev, imx6_pcie->wake_up_gpio,
+				    GPIOF_IN,
+				    "PCIe wake up");
+
+	imx6_pcie->disable_gpio = of_get_named_gpio(np, "disable-gpio", 0);
+	if (gpio_is_valid(imx6_pcie->disable_gpio))
+		devm_gpio_request_one(&pdev->dev, imx6_pcie->disable_gpio,
+				    GPIOF_OUT_INIT_HIGH,
+				    "PCIe disable endpoint");
+
+	/* Fetch clocks */
+	imx6_pcie->lvds1_sel = clk_get(&pdev->dev, "lvds1_sel");
+	if (IS_ERR(imx6_pcie->lvds1_sel)) {
+		dev_err(&pdev->dev,
+			"lvds1_sel clock missing or invalid\n");
+		ret = PTR_ERR(imx6_pcie->lvds1_sel);

drivers/pci/host/pci-imx6.c line 467

Quoted 10 lines
drivers/pci/host/pci-imx6.c new file +10 -0
+		goto err;
+	}
+
+	imx6_pcie->lvds1_gate = clk_get(&pdev->dev, "lvds1_gate");
+	if (IS_ERR(imx6_pcie->lvds1_gate)) {
+		dev_err(&pdev->dev,
+			"lvds1_gate clock select missing or invalid\n");
+		ret = PTR_ERR(imx6_pcie->lvds1_gate);
+		goto err;
+	}

devm_clk_get(). Otherwise you need to release the clock un unregister/probe failure.

drivers/pci/host/pci-imx6.c line 519

Quoted 7 lines
drivers/pci/host/pci-imx6.c new file +7 -0
+static int __exit imx6_pcie_remove(struct platform_device *pdev)
+{
+	struct imx6_pcie *imx6_pcie = platform_get_drvdata(pdev);
+
+	clk_disable_unprepare(imx6_pcie->pcie_axi);
+	clk_disable_unprepare(imx6_pcie->lvds1_gate);
+	clk_disable_unprepare(imx6_pcie->pcie_ref_125m);

Still no unregister for the pcie controller?

drivers/pci/host/pci-imx6.c line 94

Quoted 4 lines
drivers/pci/host/pci-imx6.c new file +4 -0
+
+	return 0;
+}
+

Sascha

Signature · 4 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
author
#5 lore raw

PATCH v3 3/3 PCI: imx6: Add support for i.MX6 PCIe controller

Quoted 17 lines

Sean,

Several more comments.

Shawn,

A question about a clk_set_parent inside.

drivers/pci/host/pci-imx6.c line 49

Quoted 3 lines · Sean Cross
drivers/pci/host/pci-imx6.c new file +3 -0
+
+#define IMX6_ENTER_RESET 0
+#define IMX6_EXIT_RESET 1

These are unused

Quoted 8 lines

drivers/pci/host/pci-imx6.c line 52

Quoted 3 lines
drivers/pci/host/pci-imx6.c new file +3 -0
+
+#define IMX6_POWER_OFF 0
+#define IMX6_POWER_ON 1

unused aswell

Thanks. These leaked out from an earlier revision of the code. I'll remove them.

Quoted 10 lines
Quoted 10 lines
drivers/pci/host/pci-imx6.c new file +9 -0
+static int pcie_phy_poll_ack(void __iomem *dbi_base, int max_iterations,
+ int exp_val)
+{
+ u32 val;
+ u32 wait_counter = 0;
+
+ do {
+ val = readl(dbi_base + PCIE_PHY_STAT);
+ val = (val >> PCIE_PHY_STAT_ACK_LOC) & 0x1;
Quoted 8 lines
Quoted 2 lines

+ wait_counter++;
+ } while ((wait_counter < max_iterations) && (val != exp_val));

may_iterations is never something else than 100 so you should drop the argument.
Also I would prefer a real timeout here rather than a counter.

Is there a construct to have a real timer? Would a completion work here instead?

Quoted 8 lines
Quoted 3 lines

+
+ if (val != exp_val)
+ return -1;

By saying "A negative error value" I actually meant one of include/uapi/asm-generic/errno*

Of course. How silly of me. I'll fix that correctly.

Quoted 30 lines
Quoted 7 lines
drivers/pci/host/pci-imx6.c new file +7 -0
+static int pcie_phy_write(void __iomem *dbi_base, int addr, int data)
+{
+ u32 var;
+
+ /* write addr */
+ /* cap addr */
+ if (pcie_phy_wait_ack(dbi_base, addr))

drivers/pci/host/pci-imx6.c line 160

Quoted 10 lines
drivers/pci/host/pci-imx6.c new file +10 -0
+ return -1;
+
+ var = data << PCIE_PHY_CTRL_DATA_LOC;
+ writel(var, dbi_base + PCIE_PHY_CTRL);
+
+ /* capture data */
+ var |= (0x1 << PCIE_PHY_CTRL_CAP_DAT_LOC);
+ writel(var, dbi_base + PCIE_PHY_CTRL);
+
+ /* wait for ack */

Drop this comment.

Quoted 3 lines

+ if (pcie_phy_poll_ack(dbi_base, 100, 1))
+ return -1;
+

...

Quoted 11 lines

drivers/pci/host/pci-imx6.c line 216

Quoted 7 lines
drivers/pci/host/pci-imx6.c new file +7 -0
+static int imx6_pcie_deassert_core_reset(struct pcie_port *pp)
+{
+ int ret;
+ struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
+
+ if (imx6_pcie->power_on_gpio >= 0)
+ gpio_set_value(imx6_pcie->power_on_gpio, IMX6_POWER_ON);

in probe you used gpio_is_valid(). Why not here?

Again, leftover from when that used to be exynos_pcie_assert_reset(). I'll change it to use gpio_is_valid().

Quoted 8 lines
Quoted 8 lines
drivers/pci/host/pci-imx6.c new file +8 -0
+
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_TEST_PD, 0 << 18);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_REF_CLK_EN, 1 << 16);
+
+ ret = clk_set_parent(imx6_pcie->lvds1_sel, imx6_pcie->sata_ref);
+ if (ret) {
Quoted 8 lines
Quoted 3 lines

+ dev_err(pp->dev, "unable to set lvds1_gate parent\n");
+ goto err_set_parent;
+ }

I'm unsure this should be done here. Shawn, should we do this in SoC code?

A different board could easily use lvds2 to drive the PCIe clock. I think that I should change the variable names to simply "lvds_sel".

Quoted 22 lines
Quoted 22 lines
drivers/pci/host/pci-imx6.c new file +22 -0
+
+ ret = clk_prepare_enable(imx6_pcie->pcie_ref_125m);
+ if (ret) {
+ dev_err(pp->dev, "unable to enable pcie_ref_125m\n");
+ goto err_pcie_ref;
+ }
+
+ ret = clk_prepare_enable(imx6_pcie->lvds1_gate);
+ if (ret) {
+ dev_err(pp->dev, "unable to enable lvds1_gate\n");
+ goto err_lvds1_gate;
+ }
+
+ ret = clk_prepare_enable(imx6_pcie->pcie_axi);
+ if (ret) {
+ dev_err(pp->dev, "unable to enable pcie_axi\n");
+ goto err_pcie_axi;
+ }
+
+ /* allow the clocks to stabilize */
+ usleep_range(100, 200);
+
Quoted 8 lines

drivers/pci/host/pci-imx6.c line 253

Quoted 4 lines

+ return 0;

drivers/pci/host/pci-imx6.c new file +3 -0
+
+err_pcie_axi:
+ clk_disable(imx6_pcie->lvds1_gate);

The counterpart of clk_prepare_enable is clk_disable_unprepare.

I'll fix this, too.

Quoted 9 lines
Quoted 5 lines

+ return;
+ }
+ }
+
+ return;

unnecessary return

I'll turn it into a "break" then.

Quoted 10 lines
Quoted 6 lines

+
+ imx6_pcie->power_on_gpio = of_get_named_gpio(np, "power-on-gpio", 0);
+ if (gpio_is_valid(imx6_pcie->power_on_gpio))
+ devm_gpio_request_one(&pdev->dev, imx6_pcie->power_on_gpio,
+ GPIOF_OUT_INIT_LOW,
+ "PCIe power enable");

devm_gpio_request_one can still fail.

It can fail, but it's only critical for the power switch. However, arguably it's a critical error even if these GPIOs can't be allocated, so I'll go ahead and add the same consistency check and error return code to the other three switches.

Quoted 26 lines
Quoted 26 lines
drivers/pci/host/pci-imx6.c new file +26 -0
+
+ imx6_pcie->wake_up_gpio = of_get_named_gpio(np, "wake-up-gpio", 0);
+ if (gpio_is_valid(imx6_pcie->wake_up_gpio))
+ devm_gpio_request_one(&pdev->dev, imx6_pcie->wake_up_gpio,
+ GPIOF_IN,
+ "PCIe wake up");
+
+ imx6_pcie->disable_gpio = of_get_named_gpio(np, "disable-gpio", 0);
+ if (gpio_is_valid(imx6_pcie->disable_gpio))
+ devm_gpio_request_one(&pdev->dev, imx6_pcie->disable_gpio,
+ GPIOF_OUT_INIT_HIGH,
+ "PCIe disable endpoint");
+
+ /* Fetch clocks */
+ imx6_pcie->lvds1_sel = clk_get(&pdev->dev, "lvds1_sel");
+ if (IS_ERR(imx6_pcie->lvds1_sel)) {
+ dev_err(&pdev->dev,
+ "lvds1_sel clock missing or invalid\n");
+ ret = PTR_ERR(imx6_pcie->lvds1_sel);
+ goto err;
+ }
+
+ imx6_pcie->lvds1_gate = clk_get(&pdev->dev, "lvds1_gate");
+ if (IS_ERR(imx6_pcie->lvds1_gate)) {
+ dev_err(&pdev->dev,
+ "lvds1_gate clock select missing or invalid\n");
Quoted 8 lines
Quoted 3 lines

+ ret = PTR_ERR(imx6_pcie->lvds1_gate);
+ goto err;
+ }

devm_clk_get(). Otherwise you need to release the clock un unregister/probe failure.

Good point.

Quoted 11 lines

drivers/pci/host/pci-imx6.c line 519

Quoted 7 lines
drivers/pci/host/pci-imx6.c new file +7 -0
+static int __exit imx6_pcie_remove(struct platform_device *pdev)
+{
+ struct imx6_pcie *imx6_pcie = platform_get_drvdata(pdev);
+
+ clk_disable_unprepare(imx6_pcie->pcie_axi);
+ clk_disable_unprepare(imx6_pcie->lvds1_gate);
+ clk_disable_unprepare(imx6_pcie->pcie_ref_125m);

Still no unregister for the pcie controller?

The Designware core doesn't support unregistering (or even module unloading). I'm not sure how to handle that case. For that matter, when is remove() even called on a module that can't be unloaded?

maintainer
#6 lore raw

PATCH v3 3/3 PCI: imx6: Add support for i.MX6 PCIe controller

Quoted 45 lines · Sean Cross
Quoted 17 lines

Sean,

Several more comments.

Shawn,

A question about a clk_set_parent inside.

drivers/pci/host/pci-imx6.c line 49

Quoted 3 lines · Sean Cross
drivers/pci/host/pci-imx6.c new file +3 -0
+
+#define IMX6_ENTER_RESET 0
+#define IMX6_EXIT_RESET 1

These are unused

Quoted 8 lines

drivers/pci/host/pci-imx6.c line 52

Quoted 3 lines
drivers/pci/host/pci-imx6.c new file +3 -0
+
+#define IMX6_POWER_OFF 0
+#define IMX6_POWER_ON 1

unused aswell

Thanks. These leaked out from an earlier revision of the code. I'll remove them.

Quoted 10 lines
Quoted 10 lines
drivers/pci/host/pci-imx6.c new file +9 -0
+static int pcie_phy_poll_ack(void __iomem *dbi_base, int max_iterations,
+ int exp_val)
+{
+ u32 val;
+ u32 wait_counter = 0;
+
+ do {
+ val = readl(dbi_base + PCIE_PHY_STAT);
+ val = (val >> PCIE_PHY_STAT_ACK_LOC) & 0x1;
Quoted 8 lines
Quoted 2 lines

+ wait_counter++;
+ } while ((wait_counter < max_iterations) && (val != exp_val));

may_iterations is never something else than 100 so you should drop the argument.
Also I would prefer a real timeout here rather than a counter.

Quoted 1 line

Is there a construct to have a real timer? Would a completion work here instead?

A completion is overkill. Polling is fine, but it should be a well defined amount of time which is independent of current cpu speed. Adding a udelay(1) to the loop should be enough.

Quoted 6 lines
Quoted 4 lines

I'm unsure this should be done here. Shawn, should we do this in SoC code?

A different board could easily use lvds2 to drive the PCIe clock. I think that I should change the variable names to simply "lvds_sel".

Why should it use a different clock? It's fine to make this configurable, but only if we actually know the reasons why it should be configurable.

Even if it should be configurable I'm still unsure whether this should be done at pci driver level.

Quoted 4 lines
Quoted 3 lines

devm_gpio_request_one can still fail.

It can fail, but it's only critical for the power switch. However, arguably it's a critical error even if these GPIOs can't be allocated, so I'll go ahead and add the same consistency check and error return code to the other three switches.

If you want to make the gpios optional that's fine, but when of_get_named_gpio succeeds, then devm_gpio_request_one should succeed aswell, otherwise there's something wrong.

Quoted 10 lines
Quoted 9 lines
Quoted 5 lines

+ struct imx6_pcie *imx6_pcie = platform_get_drvdata(pdev); +
+ clk_disable_unprepare(imx6_pcie->pcie_axi);
+ clk_disable_unprepare(imx6_pcie->lvds1_gate);
+ clk_disable_unprepare(imx6_pcie->pcie_ref_125m);

Still no unregister for the pcie controller?

The Designware core doesn't support unregistering (or even module unloading). I'm not sure how to handle that case. For that matter, when is remove() even called on a module that can't be unloaded?

Then don't implement the remove callback. That's better than providing a bogus remove function.

Sascha

Signature · 4 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
author
#7 lore raw

PATCH v3 3/3 PCI: imx6: Add support for i.MX6 PCIe controller

Quoted 27 lines · Sascha Hauer
Quoted 26 lines · Sean Cross
Quoted 23 lines

Sean,

Several more comments.

drivers/pci/host/pci-imx6.c line 87

Quoted 11 lines
drivers/pci/host/pci-imx6.c new file +11 -0
+static int pcie_phy_poll_ack(void __iomem *dbi_base, int max_iterations,
+ int exp_val)
+{
+ u32 val;
+ u32 wait_counter = 0;
+
+ do {
+ val = readl(dbi_base + PCIE_PHY_STAT);
+ val = (val >> PCIE_PHY_STAT_ACK_LOC) & 0x1;
+ wait_counter++;
+ } while ((wait_counter < max_iterations) && (val != exp_val));

may_iterations is never something else than 100 so you should drop the argument.
Also I would prefer a real timeout here rather than a counter.

Quoted 5 lines
Quoted 1 line

Is there a construct to have a real timer? Would a completion work here instead?

A completion is overkill. Polling is fine, but it should be a well defined amount of time which is independent of current cpu speed. Adding a udelay(1) to the loop should be enough.

In that case, it makes sense to drop the max_iterations value by a factor of 10 or so.

Quoted 7 lines
Quoted 7 lines
Quoted 4 lines

I'm unsure this should be done here. Shawn, should we do this in SoC code?

Quoted 8 lines
Quoted 1 line

A different board could easily use lvds2 to drive the PCIe clock. I think that I should change the variable names to simply "lvds_sel".

Why should it use a different clock? It's fine to make this configurable, but only if we actually know the reasons why it should be configurable.

Even if it should be configurable I'm still unsure whether this should be done at pci driver level.

I'm a bit wary of including clock setup like this in the SoC code, as different boards might be different. If a board designer wants to run LVDS2 to the PCIe slot, that's entirely acceptable. It might not actually ever get done, but it seems like the sort of board-specific thing that device tree was designed to handle.

Quoted 9 lines
Quoted 3 lines
Quoted 1 line

devm_gpio_request_one can still fail.

It can fail, but it's only critical for the power switch. However, arguably it's a critical error even if these GPIOs can't be allocated, so I'll go ahead and add the same consistency check and error return code to the other three switches.

If you want to make the gpios optional that's fine, but when of_get_named_gpio succeeds, then devm_gpio_request_one should succeed aswell, otherwise there's something wrong.

Ah, alright. I'll add the errors, then.

Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 5 lines

+ struct imx6_pcie *imx6_pcie = platform_get_drvdata(pdev); +
+ clk_disable_unprepare(imx6_pcie->pcie_axi);
+ clk_disable_unprepare(imx6_pcie->lvds1_gate);
+ clk_disable_unprepare(imx6_pcie->pcie_ref_125m);

Quoted 7 lines
Quoted 2 lines
Quoted 1 line

Still no unregister for the pcie controller?

The Designware core doesn't support unregistering (or even module unloading). I'm not sure how to handle that case. For that matter, when is remove() even called on a module that can't be unloaded?

Then don't implement the remove callback. That's better than providing a bogus remove function.

I'll cut out the remove() function.

maintainer
#8 lore raw

PATCH v3 3/3 PCI: imx6: Add support for i.MX6 PCIe controller

Quoted 8 lines · Sean Cross
Quoted 2 lines

Even if it should be configurable I'm still unsure whether this should be done at pci driver level.

I'm a bit wary of including clock setup like this in the SoC code, as different boards might be different. If a board designer wants to run LVDS2 to the PCIe slot, that's entirely acceptable. It might not actually ever get done, but it seems like the sort of board-specific thing that device tree was designed to handle.

The devicetree was designed to handle hardware descriptions, not configuration options.

Chosing the clock parent is probably in the grey area between hardware description and configuration, so I assume when we find a good reason to add this option to the devicetree then it's acceptable to add it there.

But we shouldn't add this option for something that, as you say, 'might not actually ever get done'. Just hardcode the clock selection in SoC code for now. If someone ever finds the good reason to make this configurable then he will speak up and we can discuss this again.

Sascha

Signature · 4 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
#9 lore raw

PATCH v3 3/3 PCI: imx6: Add support for i.MX6 PCIe controller

In reply to Sean Cross

Hi Sean Cross:
See my comments marked by Richard.

Best Regards
Richard Zhu

-----Original Message-----
From: [email protected] [mailto:linux-pci-owner at vger.kernel.org] On Behalf Of Sean Cross
Sent: Thursday, September 12, 2013 12:04 PM
To: devicetree at vger.kernel.org; linux-pci at vger.kernel.org; linux-arm-kernel at lists.infradead.org
Cc: Sascha Hauer; Sean Cross
Subject: [PATCH v3 3/3] PCI: imx6: Add support for i.MX6 PCIe controller

Add support for the PCIe port present on the i.MX6 family of controllers. These use the Synopsis Designware core tied to their own PHY.

---
 .../devicetree/bindings/pci/designware-pcie.txt    |    5 +
 arch/arm/boot/dts/imx6qdl.dtsi                     |   18 +
 arch/arm/mach-imx/Kconfig                          |    2 +
 drivers/pci/host/Kconfig                           |    6 +
 drivers/pci/host/Makefile                          |    1 +
 drivers/pci/host/pci-imx6.c                        |  549 ++++++++++++++++++++
 6 files changed, 581 insertions(+)
 create mode 100644 drivers/pci/host/pci-imx6.c
Documentation/devicetree/bindings/pci/designware-pcie.txt +6 -0
index eabcb4b..41d8419 100644
@@ -21,6 +21,11 @@ Required properties:
 - num-lanes: number of lanes to use
 - reset-gpio: gpio pin number of power good signal
 
+Optional properties for fsl,imx6-pcie
+- power-on-gpio: gpio pin number of power-enable signal
+- wake-up-gpio: gpio pin number of incoming wakeup signal
+- disable-gpio: gpio pin number of outgoing rfkill/endpoint disable 
+signal
+
 Example:
 

SoC specific DT Entry:

arch/arm/boot/dts/imx6qdl.dtsi +11 -0
@@ -116,6 +116,24 @@
 			arm,data-latency = <4 2 3>;
 		};
 
+		pcie: pcie at 0x01000000 {
+			compatible = "fsl,imx6-pcie", "snps,dw-pcie";
+			reg = <0x01ffc000 0x4000>; /* DBI */
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x000fc000   /* configuration space */
+				  0x81000000 0 0          0x01000000 0 0x00100000   /* downstream I/O */
+				  0x82000000 0 0x01100000 0x01100000 0 0x00e00000>; /* 
+non-prefetchable memory */

[Richard] It's better to arrange the memory layout like the following one, then the 8MB mem-space can be allocated.

                        ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000   /* configuration space */
                                  0x81000000 0 0          0x01f80000 0 0x00010000   /* downstream I/O */
                                  0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */

+
+ num-lanes = <1>;
+ interrupts = <0 123 0x04>;
+ clocks = <&clks 186>, <&clks 189>, <&clks 203>, <&clks 205>, <&clks 144>;
+ clock-names = "sata_ref", "pcie_ref_125m", "lvds1_sel", "lvds1_gate", "pcie_axi";
+ status = "disabled";
+ };
+
pmu {
compatible = "arm,cortex-a9-pmu"; interrupts = <0 94 0x04>;

arch/arm/mach-imx/Kconfig +2 -0
@@ -801,6 +801,8 @@ config SOC_IMX6Q
 	select HAVE_IMX_SRC
 	select HAVE_SMP
 	select MFD_SYSCON
+	select MIGHT_HAVE_PCI
+	select PCI_DOMAINS if PCI
 	select PINCTRL
 	select PINCTRL_IMX6Q
 	select PL310_ERRATA_588369 if CACHE_PL310 diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig index 3d95048..efa24d9 100644
drivers/pci/host/Kconfig +6 -0
@@ -15,6 +15,12 @@ config PCI_EXYNOS
 	select PCIEPORTBUS
 	select PCIE_DW
 
+config PCI_IMX6
+	bool "Freescale i.MX6 PCIe controller"
+	depends on SOC_IMX6Q
+	select PCIEPORTBUS
+	select PCIE_DW
+
 config PCI_TEGRA
 	bool "NVIDIA Tegra PCIe controller"
 	depends on ARCH_TEGRA
drivers/pci/host/Makefile +1 -0
@@ -1,4 +1,5 @@
 obj-$(CONFIG_PCIE_DW) += pcie-designware.o
 obj-$(CONFIG_PCI_EXYNOS) += pci-exynos.o
+obj-$(CONFIG_PCI_IMX6) += pci-imx6.o
 obj-$(CONFIG_PCI_MVEBU) += pci-mvebu.o
 obj-$(CONFIG_PCI_TEGRA) += pci-tegra.o
drivers/pci/host/pci-imx6.c new file +112 -0

112 lines not on this page · raw message

[Richard]16-bit?

+*/ static int pcie_phy_read(void __iomem *dbi_base, int addr , int +*data) {
+ u32 val, phy_ctl;
+
+ if (pcie_phy_wait_ack(dbi_base, addr))
+ return -1;
+
+ /* assert Read signal */
+ phy_ctl = 0x1 << PCIE_PHY_CTRL_RD_LOC;
+ writel(phy_ctl, dbi_base + PCIE_PHY_CTRL);
+
+ if (pcie_phy_poll_ack(dbi_base, 100, 1))
+ return -1;
+
+ val = readl(dbi_base + PCIE_PHY_STAT);
+ *data = (val & (0xffff << PCIE_PHY_STAT_DATA_LOC));
+
+ /* deassert Read signal */
+ writel(0x00, dbi_base + PCIE_PHY_CTRL);
+
+ if (pcie_phy_poll_ack(dbi_base, 100, 0))
+ return -1;
+
+ return 0;
+}
+
+static int pcie_phy_write(void __iomem *dbi_base, int addr, int data) {
+ u32 var;
+
+ /* write addr */
+ /* cap addr */
+ if (pcie_phy_wait_ack(dbi_base, addr))
+ return -1;
+
+ var = data << PCIE_PHY_CTRL_DATA_LOC;
+ writel(var, dbi_base + PCIE_PHY_CTRL);
+
+ /* capture data */
+ var |= (0x1 << PCIE_PHY_CTRL_CAP_DAT_LOC);
+ writel(var, dbi_base + PCIE_PHY_CTRL);
+
+ /* wait for ack */
+ if (pcie_phy_poll_ack(dbi_base, 100, 1))
+ return -1;
+
+ /* deassert cap data */
+ var = data << PCIE_PHY_CTRL_DATA_LOC;
+ writel(var, dbi_base + PCIE_PHY_CTRL);
+
+ /* wait for ack de-assetion */
+ if (pcie_phy_poll_ack(dbi_base, 100, 0))
+ return -1;
+
+ /* assert wr signal */
+ var = 0x1 << PCIE_PHY_CTRL_WR_LOC;
+ writel(var, dbi_base + PCIE_PHY_CTRL);
+
+ /* wait for ack */
+ if (pcie_phy_poll_ack(dbi_base, 100, 1))
+ return -1;
+
+ /* deassert wr signal */
+ var = data << PCIE_PHY_CTRL_DATA_LOC;
+ writel(var, dbi_base + PCIE_PHY_CTRL);
+
+ /* wait for ack de-assetion */
+ if (pcie_phy_poll_ack(dbi_base, 100, 0))
+ return -1;
+
+ writel(0x0, dbi_base + PCIE_PHY_CTRL);
+
+ return 0;
+}
+
+static int imx6_pcie_assert_core_reset(struct pcie_port *pp) {
+ struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_TEST_PD, 1 << 18);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6Q_GPR12_PCIE_CTL_2, 1 << 10);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_REF_CLK_EN, 0 << 16);
+
+ gpio_set_value(imx6_pcie->reset_gpio, 0);
+ msleep(100);
+ gpio_set_value(imx6_pcie->reset_gpio, 1);
+
+ return 0;
+}
+
+static int imx6_pcie_deassert_core_reset(struct pcie_port *pp) {
+ int ret;
+ struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
+
+ if (imx6_pcie->power_on_gpio >= 0)
+ gpio_set_value(imx6_pcie->power_on_gpio, IMX6_POWER_ON);
+
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_TEST_PD, 0 << 18);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_REF_CLK_EN, 1 << 16);
+
+ ret = clk_set_parent(imx6_pcie->lvds1_sel, imx6_pcie->sata_ref);
+ if (ret) {
+ dev_err(pp->dev, "unable to set lvds1_gate parent\n");
+ goto err_set_parent;
+ }
+
+ ret = clk_prepare_enable(imx6_pcie->pcie_ref_125m);
+ if (ret) {
+ dev_err(pp->dev, "unable to enable pcie_ref_125m\n");
+ goto err_pcie_ref;
+ }
+
+ ret = clk_prepare_enable(imx6_pcie->lvds1_gate);
+ if (ret) {
+ dev_err(pp->dev, "unable to enable lvds1_gate\n");
+ goto err_lvds1_gate;
+ }
+
[Richard] As we know that lvds1 can be configured as input or output. How do you present them by the name of "lvds1_gate"?

+ ret = clk_prepare_enable(imx6_pcie->pcie_axi);
+ if (ret) {
+ dev_err(pp->dev, "unable to enable pcie_axi\n");
+ goto err_pcie_axi;
+ }
+
+ /* allow the clocks to stabilize */
+ usleep_range(100, 200);
+
+ return 0;
+
+err_pcie_axi:
+ clk_disable(imx6_pcie->lvds1_gate);
+err_lvds1_gate:
+ clk_disable(imx6_pcie->pcie_ref_125m);
+err_pcie_ref:
+err_set_parent:
+ return ret;
+}
+
+static void imx6_pcie_init_phy(struct pcie_port *pp) {
+ struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
+
+ /* FIXME the field name should be aligned to RM */
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6Q_GPR12_PCIE_CTL_2, 0 << 10);
+
+ /* configure constant input signal to the pcie ctrl and phy */
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6Q_GPR12_DEVICE_TYPE, PCI_EXP_TYPE_ROOT_PORT << 12);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6Q_GPR12_LOS_LEVEL, 9 << 4);
+
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_DEEMPH_GEN1, 0 << 0);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_DEEMPH_GEN2_3P5DB, 0 << 6);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_DEEMPH_GEN2_6DB, 20 << 12);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_SWING_FULL, 127 << 18);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR8,
+ IMX6Q_GPR8_TX_SWING_LOW, 127 << 25); }
+
+static void imx6_pcie_host_init(struct pcie_port *pp) {
+ int count = 0;
+ struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
+
+ imx6_pcie_assert_core_reset(pp);
+
+ imx6_pcie_init_phy(pp);
+
+ imx6_pcie_deassert_core_reset(pp);
+
+ dw_pcie_setup_rc(pp);
+
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6Q_GPR12_PCIE_CTL_2, 1 << 10);
+
+ while (!dw_pcie_link_up(pp)) {
+ mdelay(100);
[Richard] mdelay(100) is too long, please use usleep_range(xxx,xxx).
+ count++;
+ if (count >= 10) {
+ dev_err(pp->dev, "phy link never came up\n");
+ dev_dbg(pp->dev,"DEBUG_R0: 0x%08x, DEBUG_R1: 0x%08x\n",
+ readl(pp->dbi_base + PCIE_PHY_DEBUG_R0),
+ readl(pp->dbi_base + PCIE_PHY_DEBUG_R1));
+ return;
+ }
+ }
+
+ return;
+}
+
+static int imx6_pcie_link_up(struct pcie_port *pp) {
+ u32 rc, ltssm, rx_valid, temp;
+
+ /* link is debug bit 36, debug register 1 starts at bit 32 */
+ rc = readl(pp->dbi_base + PCIE_PHY_DEBUG_R1) & (0x1 << (36 - 32));
+ if (rc)
+ return -1;
+
+ /* From L0, initiate MAC entry to gen2 if EP/RC supports gen2.
+ * Wait 2ms (LTSSM timeout is 24ms, PHY lock is ~5us in gen2).
+ * If (MAC/LTSSM.state == Recovery.RcvrLock)
+ * && (PHY/rx_valid==0) then pulse PHY/rx_reset. Transition
+ * to gen2 is stuck
+ */
+ pcie_phy_read(pp->dbi_base, PCIE_PHY_RX_ASIC_OUT, &rx_valid);
+ ltssm = readl(pp->dbi_base + PCIE_PHY_DEBUG_R0) & 0x3F;
+
+ if (rx_valid & 0x01)
+ return 0;
+
+ if (ltssm != 0x0d)
+ return 0;
+
+ dev_err(pp->dev,
+ "transition to gen2 is stuck, reset PHY!\n");
+
+ pcie_phy_read(pp->dbi_base,
+ PHY_RX_OVRD_IN_LO, &temp);
+ temp |= (PHY_RX_OVRD_IN_LO_RX_DATA_EN
+ | PHY_RX_OVRD_IN_LO_RX_PLL_EN);
+ pcie_phy_write(pp->dbi_base,
+ PHY_RX_OVRD_IN_LO, temp);
+
+ usleep_range(2000, 3000);
+
+ pcie_phy_read(pp->dbi_base,
+ PHY_RX_OVRD_IN_LO, &temp);
+ temp &= ~(PHY_RX_OVRD_IN_LO_RX_DATA_EN
+ | PHY_RX_OVRD_IN_LO_RX_PLL_EN);
+ pcie_phy_write(pp->dbi_base,
+ PHY_RX_OVRD_IN_LO, temp);
+
+ return 0;
+}
+
+static struct pcie_host_ops imx6_pcie_host_ops = {
+ .link_up = imx6_pcie_link_up,
+ .host_init = imx6_pcie_host_init,
+};
+
+static int add_pcie_port(struct pcie_port *pp, struct platform_device +*pdev) {
+ int ret;
+
+ pp->irq = platform_get_irq(pdev, 0);
+ if (!pp->irq) {
+ dev_err(&pdev->dev, "failed to get irq\n");
+ return -ENODEV;
+ }
+
+ pp->root_bus_nr = -1;
+ pp->ops = &imx6_pcie_host_ops;
+
+ spin_lock_init(&pp->conf_lock);
+ ret = dw_pcie_host_init(pp);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to initialize host\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int __init imx6_pcie_probe(struct platform_device *pdev) {
+ struct imx6_pcie *imx6_pcie;
+ struct pcie_port *pp;
+ struct device_node *np = pdev->dev.of_node;
+ struct resource *dbi_base;
+ int ret;
+
+ imx6_pcie = devm_kzalloc(&pdev->dev, sizeof(*imx6_pcie),
+ GFP_KERNEL);
+ if (!imx6_pcie)
+ return -ENOMEM;
+
+ pp = &imx6_pcie->pp;
+ pp->dev = &pdev->dev;
+
+ dbi_base = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!dbi_base) {
+ dev_err(&pdev->dev, "dbi_base memory resource not found\n");
+ return -ENODEV;
+ }
+
+ pp->dbi_base = devm_request_and_ioremap(&pdev->dev, dbi_base);
+ if (IS_ERR(pp->dbi_base)) {
+ dev_err(&pdev->dev, "unable to remap dbi_base\n");
+ ret = PTR_ERR(pp->dbi_base);
+ goto err;
+ }
+
+ /* Fetch GPIOs */
+ imx6_pcie->reset_gpio = of_get_named_gpio(np, "reset-gpio", 0);
+ if (gpio_is_valid(imx6_pcie->reset_gpio)) {
+ ret = devm_gpio_request_one(&pdev->dev,
+ imx6_pcie->reset_gpio,
+ GPIOF_OUT_INIT_LOW,
+ "PCIe reset");
+ if (ret) {
+ dev_err(&pdev->dev, "unable to get reset line\n");
+ goto err;
+ }
+ }
+
+ imx6_pcie->power_on_gpio = of_get_named_gpio(np, "power-on-gpio", 0);
+ if (gpio_is_valid(imx6_pcie->power_on_gpio))
+ devm_gpio_request_one(&pdev->dev, imx6_pcie->power_on_gpio,
+ GPIOF_OUT_INIT_LOW,
+ "PCIe power enable");
+
+ imx6_pcie->wake_up_gpio = of_get_named_gpio(np, "wake-up-gpio", 0);
+ if (gpio_is_valid(imx6_pcie->wake_up_gpio))
+ devm_gpio_request_one(&pdev->dev, imx6_pcie->wake_up_gpio,
+ GPIOF_IN,
+ "PCIe wake up");
+
+ imx6_pcie->disable_gpio = of_get_named_gpio(np, "disable-gpio", 0);
+ if (gpio_is_valid(imx6_pcie->disable_gpio))
+ devm_gpio_request_one(&pdev->dev, imx6_pcie->disable_gpio,
+ GPIOF_OUT_INIT_HIGH,
+ "PCIe disable endpoint");
+
+ /* Fetch clocks */
+ imx6_pcie->lvds1_sel = clk_get(&pdev->dev, "lvds1_sel");
+ if (IS_ERR(imx6_pcie->lvds1_sel)) {
+ dev_err(&pdev->dev,
+ "lvds1_sel clock missing or invalid\n");
+ ret = PTR_ERR(imx6_pcie->lvds1_sel);
+ goto err;
+ }
+
+ imx6_pcie->lvds1_gate = clk_get(&pdev->dev, "lvds1_gate");
+ if (IS_ERR(imx6_pcie->lvds1_gate)) {
+ dev_err(&pdev->dev,
+ "lvds1_gate clock select missing or invalid\n");
+ ret = PTR_ERR(imx6_pcie->lvds1_gate);
+ goto err;
+ }
+
+ imx6_pcie->pcie_ref_125m = clk_get(&pdev->dev, "pcie_ref_125m");
+ if (IS_ERR(imx6_pcie->pcie_ref_125m)) {
+ dev_err(&pdev->dev,
+ "pcie_ref_125m clock source missing or invalid\n");
+ ret = PTR_ERR(imx6_pcie->pcie_ref_125m);
+ goto err;
+ }
+
+ imx6_pcie->pcie_axi = clk_get(&pdev->dev, "pcie_axi");
+ if (IS_ERR(imx6_pcie->pcie_axi)) {
+ dev_err(&pdev->dev,
+ "pcie_axi clock source missing or invalid\n");
+ ret = PTR_ERR(imx6_pcie->pcie_axi);
+ goto err;
+ }
+
+ imx6_pcie->sata_ref = clk_get(&pdev->dev, "sata_ref");
+ if (IS_ERR(imx6_pcie->sata_ref)) {
+ dev_err(&pdev->dev,
+ "sata_ref clock source missing or invalid\n");
+ ret = PTR_ERR(imx6_pcie->sata_ref);
+ goto err;
+ }
+
+ /* Grab GPR config register range */
+ imx6_pcie->iomuxc_gpr =
+ syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
+ if (IS_ERR(imx6_pcie->iomuxc_gpr)) {
+ dev_err(&pdev->dev, "unable to find iomuxc registers\n");
+ ret = PTR_ERR(imx6_pcie->iomuxc_gpr);
+ goto err;
+ }
+
+ ret = add_pcie_port(pp, pdev);
+ if (ret < 0)
+ goto err;
+
+ platform_set_drvdata(pdev, imx6_pcie);
+ return 0;
+
+err:
+ return ret;
+}
+
+static int __exit imx6_pcie_remove(struct platform_device *pdev) {
+ struct imx6_pcie *imx6_pcie = platform_get_drvdata(pdev);
+
+ clk_disable_unprepare(imx6_pcie->pcie_axi);
+ clk_disable_unprepare(imx6_pcie->lvds1_gate);
+ clk_disable_unprepare(imx6_pcie->pcie_ref_125m);
+
+ return 0;
+}
+
+static const struct of_device_id imx6_pcie_of_match[] = {
+ { .compatible = "fsl,imx6-pcie", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, imx6_pcie_of_match);
+
+static struct platform_driver imx6_pcie_driver = {
+ .remove = __exit_p(imx6_pcie_remove),
+ .driver = {
+ .name = "imx6-pcie",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(imx6_pcie_of_match),
+ },
+};
+
+/* Freescale PCIe driver does not allow module unload */
+
+static int __init pcie_init(void)
+{
+ return platform_driver_probe(&imx6_pcie_driver, imx6_pcie_probe); }
+subsys_initcall(pcie_init);
+
+MODULE_AUTHOR("Sean Cross <[email protected]>"); +MODULE_DESCRIPTION("Freescale i.MX6 PCIe host controller driver"); +MODULE_LICENSE("GPL v2");
--
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo at vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html

author
#10 lore raw

PATCH v3 3/3 PCI: imx6: Add support for i.MX6 PCIe controller

Quoted 8 lines · On Thursday, 12 September, 2013 at 2:35 PM, Zhu Richard-R65037 wrote:

Hi Sean Cross:
See my comments marked by Richard.

[Richard] It's better to arrange the memory layout like the following one, then the 8MB mem-space can be allocated. ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 /* configuration space */
0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */
0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */

Thank you. I'll update the DT file with this new ranges.

Quoted 2 lines

+/* Read from the 16-bt PCIe PHY control registers (not memory-mapped) [Richard]16-bit?

Oops. Sloppy. Good catch.

Quoted 2 lines

[Richard] As we know that lvds1 can be configured as input or output. How do you present them by the name of "lvds1_gate"?

This particular clock maps to LVDS1/2_oben and effectively acts as a gate. Only bits 10 and 11 are exposed in clk-imx6q.c.

Quoted 2 lines

+ mdelay(100);
[Richard] mdelay(100) is too long, please use usleep_range(xxx,xxx

You're right, and 100 is entirely too long to begin with. I'll cut this value down and use a range, as suggested.