ARM: dts: mxs: Add muxing options for the SSP2 MMC
Subsystems (5)
PATCH 1/2 ARM: dts: mxs: Add muxing options for the SSP2 MMC
Add pinmux for 4-bit SD card connected to SSP2.
Signed-off-by Marek Vasut <[email protected]>
Cc Shawn Guo <[email protected]>
--- arch/arm/boot/dts/imx28.dtsi | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+)
arch/arm/boot/dts/imx28.dtsi +31 -0
@@ -473,6 +473,37 @@ fsl,pull-up = <MXS_PULL_DISABLE>; }; + mmc2_4bit_pins_a: mmc2-4bit at 0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SSP0_DATA4__SSP2_D0 + MX28_PAD_SSP1_SCK__SSP2_D1 + MX28_PAD_SSP1_CMD__SSP2_D2 + MX28_PAD_SSP0_DATA5__SSP2_D3 + MX28_PAD_SSP0_DATA6__SSP2_CMD + MX28_PAD_AUART1_RX__SSP2_CARD_DETECT + MX28_PAD_SSP0_DATA7__SSP2_SCK + >; + fsl,drive-strength = <MXS_DRIVE_8mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + + mmc2_cd_cfg: mmc2-cd-cfg { + fsl,pinmux-ids = < + MX28_PAD_AUART1_RX__SSP2_CARD_DETECT + >; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + mmc2_sck_cfg: mmc2-sck-cfg { + fsl,pinmux-ids = < + MX28_PAD_SSP0_DATA7__SSP2_SCK + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + i2c0_pins_a: i2c0 at 0 { reg = <0>; fsl,pinmux-ids = <
Signature · 1 line
1.8.4.rc3
PATCH 2/2 ARM: dts: mxs: Add MSR M28CU3 board
This board is based on the M28 SoM with custom baseboard. Supported are LEDs, ethernet, PWM, LCD, SD slots.
Signed-off-by Marek Vasut <[email protected]>
Cc Shawn Guo <[email protected]>
--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx28-m28cu3.dts | 266 +++++++++++++++++++++++++++++++++++++ arch/arm/mach-mxs/mach-mxs.c | 9 ++ 3 files changed, 276 insertions(+) create mode 100644 arch/arm/boot/dts/imx28-m28cu3.dts
arch/arm/boot/dts/Makefile +1 -0
@@ -159,6 +159,7 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \ imx28-cfa10057.dtb \ imx28-cfa10058.dtb \ imx28-evk.dtb \ + imx28-m28cu3.dtb \ imx28-m28evk.dtb \ imx28-sps1.dtb \ imx28-tx28.dtb
arch/arm/boot/dts/imx28-m28cu3.dts new file +266 -0
266 lines not on this page · raw message
arch/arm/mach-mxs/mach-mxs.c +9 -0
@@ -332,6 +332,13 @@ static void __init crystalfontz_init(void)update_fec_mac_prop (OUI_CRYSTALFONTZ ); } +static void __init m28cu3_init (void ) +{ +enable_clk_enet_out (); + +update_fec_mac_prop (OUI_DENX ); +} +static const char __init *mxs_get_soc_id (void ) {struct device_node *np;
@@ -459,6 +466,8 @@ static void __init mxs_machine_init(void)apx4devkit_init (); else if (of_machine_is_compatible("crystalfontz,cfa10036")) crystalfontz_init(); + else if (of_machine_is_compatible("msr,m28cu3")) + m28cu3_init();of_platform_populate (NULL ,of_default_bus_match_table ,NULL ,parent );
Signature · 1 line
1.8.4.rc3
PATCH 2/2 ARM: dts: mxs: Add MSR M28CU3 board
arch/arm/mach-mxs/mach-mxs.c static void __init crystalfontz_init(void) · line 337
Quoted 11 lines · Marek Vasut
arch/arm/mach-mxs/mach-mxs.c +3
-0@@ -332,6 +332,13 @@ static void __init crystalfontz_init(void)update_fec_mac_prop (OUI_CRYSTALFONTZ ); } +static void __init m28cu3_init (void ) +{ +enable_clk_enet_out ();
Since commit daa7d39 (net: freescale: fec: add support for optional enet_out clk), we can have fec driver enable the clock if you do not need the clock at the platform initialization.
Shawn
Quoted 19 lines
arch/arm/mach-mxs/mach-mxs.c +6
-0+ +update_fec_mac_prop (OUI_DENX ); +} +static const char __init *mxs_get_soc_id (void ) {struct device_node *np;@@ -459,6 +466,8 @@ static void __init mxs_machine_init(void)apx4devkit_init (); else if (of_machine_is_compatible("crystalfontz,cfa10036")) crystalfontz_init(); + else if (of_machine_is_compatible("msr,m28cu3")) + m28cu3_init();of_platform_populate (NULL ,of_default_bus_match_table ,NULL ,parent );Signature · 1 line
1.8.4.rc3
Shawn Guo
AppliedPATCH 1/2 ARM: dts: mxs: Add muxing options for the SSP2 MMC
In reply to Marek VasutQuoted 3 lines · Marek Vasut
Add pinmux for 4-bit SD card connected to SSP2.
Signed-off-by Marek Vasut <[email protected]>
Applied, thanks.