T1040QDS: Add support of 2 stage NAND boot loader
PATCH 6/6 T1040QDS: Add support of 2 stage NAND boot loader
Add support of 2 stage NAND boot loader using SPL framework.
here, PBL initialise the internal SRAM(256K) and copy SPL(192K). This further initialise DDR using SPD and environment and copy u-boot(512 kb) from NAND to DDR. Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by Prabhakar Kushwaha <[email protected]>
---
Based upon git://git.denx.de/u-boot-mpc85xx.git branch next
board/freescale/t1040qds/Makefile | 9 ++- board/freescale/t1040qds/README | 33 ++++++++++ board/freescale/t1040qds/ddr.c | 7 ++- board/freescale/t1040qds/spl.c | 122 +++++++++++++++++++++++++++++++++++++ board/freescale/t1040qds/tlb.c | 8 ++- boards.cfg | 1 + include/configs/T1040QDS.h | 58 +++++++++++++++--- 7 files changed, 227 insertions(+), 11 deletions(-) create mode 100644 board/freescale/t1040qds/spl.c
board/freescale/t1040qds/Makefile +8 -1
@@ -8,9 +8,16 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o +ifdef CONFIG_SPL_BUILD +COBJS-y += spl.o +endif + +ifndef CONFIG_SPL_BUILD COBJS-y += $(BOARD).o +COBJS-$(CONFIG_PCI) += pci.o +endif + COBJS-y += ddr.o -COBJS-$(CONFIG_PCI) += pci.o COBJS-y += law.o COBJS-y += tlb.o
board/freescale/t1040qds/README +33 -0
@@ -167,3 +167,36 @@ T1042 Personality -------------------- T1042 is a reduced personality of T1040 without Integrated 8-port Gigabit Ethernet switch. Rest of the blocks are same as T1040 + + +2 Stage boot loader +------------------- +PBL initialise the internal SRAM and copy SPL(192K) in SRAM. +SPL further initialise DDR using SPD and environment variables and copy +u-boot(512 KB) from flash to DDR. +Finally SPL transer control to u-boot for futher booting. + +SPL has following features: + - Executes within 256K + - Actual SPL size 96K + padding till 192K for extra code + - No relocation required + + Run time view of SPL framework :- + ----------------------------------------------- + Area | Address | + ----------------------------------------------- + GD, BD | 0x0xFFFC0000 (4K) | + ----------------------------------------------- + HEAP | 0xFFFC1000 (40K) grow downwards | + ----------------------------------------------- + STACK | 0xFFFD0000 (20K) grow upwards | + ----------------------------------------------- + U-boot SPL | 0xfffD0000 - 0xfffffffc (192K) | + ----------------------------------------------- + +Command to build 2 stage NAND boot loader + - modify RCW at board/freescale/t1040qds/t1040_rcw.cfg for nand boot + -66000002 00000000 fc027000 01000000 + +66000002 00000000 ec106000 01000000 + - make T1040QDS_NAND_config + - make u-boot-with-spl-pbl.bin
board/freescale/t1040qds/ddr.c +5 -2
@@ -107,11 +107,14 @@ phys_size_t initdram(int board_type)puts ("Initializing....using SPD\n" ); +#ifdef CONFIG_SPL_BUILD dram_size =fsl_ddr_sdram (); dram_size =setup_ddr_tlbs (dram_size /0x100000 ); dram_size *=0x100000 ; - -puts (" DDR: " ); +#else +puts ("DDR has been initialised by pre loader\n" ); + dram_size =0x80000000 ; +#endif return dram_size; }
board/freescale/t1040qds/spl.c new file +122 -0
122 lines not on this page · raw message
board/freescale/t1040qds/tlb.c +7 -1
@@ -52,7 +52,7 @@ struct fsl_e_tlb_entry tlb_table[] = { SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, 0, 2, BOOKE_PAGESZ_256M, 1), - +#ifndef CONFIG_SPL_BUILD /* *I*G* - PCI */ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -82,6 +82,7 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 8, BOOKE_PAGESZ_16M, 1),#endif +#endif #ifdef CONFIG_SYS_DCSRBAR_PHYS SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
@@ -103,6 +104,11 @@ struct fsl_e_tlb_entry tlb_table[] = { 0, 11, BOOKE_PAGESZ_4K, 1),#endif +#if defined(CONFIG_RAMBOOT_PBL ) && !defined(CONFIG_SPL_BUILD ) +SET_TLB_ENTRY (1 ,CONFIG_SYS_DDR_SDRAM_BASE ,CONFIG_SYS_DDR_SDRAM_BASE , +MAS3_SX |MAS3_SW |MAS3_SR ,0 , + 0, 17, BOOKE_PAGESZ_2G, 1) +#endif };int num_tlb_entries =ARRAY_SIZE (tlb_table);
boards.cfg +1 -0
@@ -958,6 +958,7 @@ Active powerpc mpc85xx - freescale t4qds Active powerpc mpc85xx - freescale t4qds T4240QDS_SPIFLASH T4240QDS:PPC_T4240,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000 - Active powerpc mpc85xx - freescale t4qds T4240QDS_SRIO_PCIE_BOOT T4240QDS:PPC_T4240,SRIO_PCIE_BOOT_SLAVE,SYS_TEXT_BASE=0xFFF80000 - Active powerpc mpc85xx - freescale t1040qds T1040QDS T1040QDS:PPC_T1040 Naveen Burmi <[email protected]> +Active powerpc mpc85xx - freescale t1040qds T1040QDS_NAND T1040QDS:PPC_T1040,RAMBOOT_PBL,NAND Poonam Aggrwal <[email protected]> Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD controlcenterd:36BIT,SDCARD Dirk Eibach <[email protected]> Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD_DEVELOP controlcenterd:36BIT,SDCARD,DEVELOP Dirk Eibach <[email protected]> Active powerpc mpc85xx - gdsys p1022 controlcenterd_TRAILBLAZER controlcenterd:TRAILBLAZER,SPIFLASH Dirk Eibach <[email protected]>
include/configs/T1040QDS.h +51 -7
104 lines not on this page · raw message
Signature · 1 line
1.7.9.5