wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware
PATCH 1/1 wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware
This is a mac80211 driver for Qualcomm WCN3660/WCN3680 devices. So far WCN3660/WCN3680 is available only on MSM platform.
Firmware can be found here:
https://www.codeaurora.org/cgit/external/hisense/platform/vendor/qcom-opensource/wlan/prima/tree/firmware_bin?h=8130_CS
Wiki page is available here:
http://wireless.kernel.org/en/users/Drivers/wcn36xx
A lot people made a contribution to this driver. Here is the list in alphabetical order:
Eugene Krasnikov <[email protected]>
Kalle Valo <[email protected]>
Olof Johansson <[email protected]>
Pontus Fuchs <[email protected]>
Yanbo Li <[email protected]>
--- MAINTAINERS | 8 + drivers/net/wireless/ath/Kconfig | 1 + drivers/net/wireless/ath/Makefile | 1 + drivers/net/wireless/ath/wcn36xx/Kconfig | 16 + drivers/net/wireless/ath/wcn36xx/Makefile | 7 + drivers/net/wireless/ath/wcn36xx/debug.c | 188 ++ drivers/net/wireless/ath/wcn36xx/debug.h | 49 + drivers/net/wireless/ath/wcn36xx/dxe.c | 805 +++++ drivers/net/wireless/ath/wcn36xx/dxe.h | 284 ++ drivers/net/wireless/ath/wcn36xx/hal.h | 4657 ++++++++++++++++++++++++++++ drivers/net/wireless/ath/wcn36xx/main.c | 1036 +++++++ drivers/net/wireless/ath/wcn36xx/pmc.c | 62 + drivers/net/wireless/ath/wcn36xx/pmc.h | 33 + drivers/net/wireless/ath/wcn36xx/smd.c | 2121 +++++++++++++ drivers/net/wireless/ath/wcn36xx/smd.h | 127 + drivers/net/wireless/ath/wcn36xx/txrx.c | 284 ++ drivers/net/wireless/ath/wcn36xx/txrx.h | 160 + drivers/net/wireless/ath/wcn36xx/wcn36xx.h | 238 ++ 18 files changed, 10077 insertions(+) create mode 100644 drivers/net/wireless/ath/wcn36xx/Kconfig create mode 100644 drivers/net/wireless/ath/wcn36xx/Makefile create mode 100644 drivers/net/wireless/ath/wcn36xx/debug.c create mode 100644 drivers/net/wireless/ath/wcn36xx/debug.h create mode 100644 drivers/net/wireless/ath/wcn36xx/dxe.c create mode 100644 drivers/net/wireless/ath/wcn36xx/dxe.h create mode 100644 drivers/net/wireless/ath/wcn36xx/hal.h create mode 100644 drivers/net/wireless/ath/wcn36xx/main.c create mode 100644 drivers/net/wireless/ath/wcn36xx/pmc.c create mode 100644 drivers/net/wireless/ath/wcn36xx/pmc.h create mode 100644 drivers/net/wireless/ath/wcn36xx/smd.c create mode 100644 drivers/net/wireless/ath/wcn36xx/smd.h create mode 100644 drivers/net/wireless/ath/wcn36xx/txrx.c create mode 100644 drivers/net/wireless/ath/wcn36xx/txrx.h create mode 100644 drivers/net/wireless/ath/wcn36xx/wcn36xx.h
MAINTAINERS +8 -0
@@ -6745,6 +6745,14 @@ L: [email protected] S: Supported F: arch/hexagon/ +QUALCOMM WCN36XX WIRELESS DRIVER +M: Eugene Krasnikov <[email protected]> +L: [email protected] +W: http://wireless.kernel.org/en/users/Drivers/wcn36xx +T: git git://github.com/KrasnikovEugene/wcn36xx.git +S: Supported +F: drivers/net/wireless/ath/wcn36xx/ + QUICKCAM PARALLEL PORT WEBCAMS M: Hans Verkuil <[email protected]> L: [email protected]
drivers/net/wireless/ath/Kconfig +1 -0
@@ -32,5 +32,6 @@ source "drivers/net/wireless/ath/ath6kl/Kconfig" source "drivers/net/wireless/ath/ar5523/Kconfig" source "drivers/net/wireless/ath/wil6210/Kconfig" source "drivers/net/wireless/ath/ath10k/Kconfig" +source "drivers/net/wireless/ath/wcn36xx/Kconfig" endif
drivers/net/wireless/ath/Makefile +1 -0
@@ -5,6 +5,7 @@ obj-$(CONFIG_ATH6KL) += ath6kl/ obj-$(CONFIG_AR5523) += ar5523/ obj-$(CONFIG_WIL6210) += wil6210/ obj-$(CONFIG_ATH10K) += ath10k/ +obj-$(CONFIG_WCN36XX) += wcn36xx/ obj-$(CONFIG_ATH_COMMON) += ath.o
drivers/net/wireless/ath/wcn36xx/Kconfig new file +16 -0
@@ -0,0 +1,16 @@ +config WCN36XX + tristate "Qualcomm Atheros WCN3660/3680 support" + depends on MAC80211 && HAS_DMA + ---help--- + This module adds support for wireless adapters based on + Qualcomm Atheros WCN3660 and WCN3680 mobile chipsets. + + If you choose to build a module, it'll be called wcn36xx. + +config WCN36XX_DEBUGFS + bool "WCN36XX debugfs support" + depends on WCN36XX + ---help--- + Enabled debugfs support + + If unsure, say Y to make it easier to debug problems.
drivers/net/wireless/ath/wcn36xx/Makefile new file +7 -0
@@ -0,0 +1,7 @@ +obj-$(CONFIG_WCN36XX) := wcn36xx.o +wcn36xx-y += main.o \ + dxe.o \ + txrx.o \ + smd.o \ + pmc.o \ + debug.o
drivers/net/wireless/ath/wcn36xx/debug.c new file +188 -0
188 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/debug.h new file +49 -0
49 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/dxe.c new file +805 -0
805 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/dxe.h new file +284 -0
284 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/hal.h new file +4657 -0
1,624 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/main.c new file +1036 -0
1,036 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/pmc.c new file +62 -0
62 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/pmc.h new file +33 -0
Lines of this file are not shown. View the raw message.
drivers/net/wireless/ath/wcn36xx/smd.c new file +2121 -0
2,121 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/smd.h new file +127 -0
127 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/txrx.c new file +284 -0
284 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/txrx.h new file +160 -0
160 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/wcn36xx.h new file +238 -0
238 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
1.8.1.2
Part of the diff is not shown here. View the raw message.
Quoted 12 lines · Eugene Krasnikov
This is a mac80211 driver for Qualcomm WCN3660/WCN3680 devices. So far WCN3660/WCN3680 is available only on MSM platform.
Firmware can be found here:
https://www.codeaurora.org/cgit/external/hisense/platform/vendor/qcom-opensource/wlan/prima/tree/firmware_bin?h=8130_CSWiki page is available here:
http://wireless.kernel.org/en/users/Drivers/wcn36xxA lot people made a contribution to this driver. Here is the list in alphabetical order:
Quoted 7 lines
Eugene Krasnikov <[email protected]>
Kalle Valo <[email protected]>
Olof Johansson <[email protected]>
Pontus Fuchs <[email protected]>
Yanbo Li <[email protected]>Signed-off-by Eugene Krasnikov <[email protected]>
Nice! I test compiled with sparse enabled and got this:
mcgrof@chalten ~/wireless-testing (git::master)$ make C=1 M=drivers/net/wireless/ath/wcn36xx/
CHECK drivers/net/wireless/ath/wcn36xx/main.c CC [M] drivers/net/wireless/ath/wcn36xx/main.o CHECK drivers/net/wireless/ath/wcn36xx/dxe.c CC [M] drivers/net/wireless/ath/wcn36xx/dxe.o CHECK drivers/net/wireless/ath/wcn36xx/txrx.c CC [M] drivers/net/wireless/ath/wcn36xx/txrx.o CHECK drivers/net/wireless/ath/wcn36xx/smd.c
/home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (4096 8) /home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (512 8) /home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (128 8) /home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (8 8) /home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (256 8) /home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (4096 8)
CC [M] drivers/net/wireless/ath/wcn36xx/smd.o CHECK drivers/net/wireless/ath/wcn36xx/pmc.c CC [M] drivers/net/wireless/ath/wcn36xx/pmc.o CHECK drivers/net/wireless/ath/wcn36xx/debug.c CC [M] drivers/net/wireless/ath/wcn36xx/debug.o
LD [M]drivers/net/wireless/ath/wcn36xx/wcn36xx.o
Building modules, stage 2.
MODPOST 1 modules
LD [M]drivers/net/wireless/ath/wcn36xx/wcn36xx.ko
Can you merge this in prior to integration as well? I've only test compiled it so would appreciate a run time test.
Luis
Quoted 1 line
From
4558cfc69270ad3ed1a480a8c846b11910af7357Mon Sep 17 00:00:00 2001
From: "Luis R. Rodriguez" <[email protected]>
Date: Fri, 4 Oct 2013 16:19:17 -0700
Subject: [PATCH] wcn36xx: add initial regulatory support
The NVRAM still needs to be processed and other requirements addressed but this should at least get this going with the default 0x64 regulatory domain on the ath module.
--- drivers/net/wireless/ath/wcn36xx/Kconfig | 1 + drivers/net/wireless/ath/wcn36xx/main.c | 34 ++++++++++++++++++++++++++++ drivers/net/wireless/ath/wcn36xx/wcn36xx.h | 2 ++ 3 files changed, 37 insertions(+)
drivers/net/wireless/ath/wcn36xx/Kconfig +1 -0
@@ -1,6 +1,7 @@ config WCN36XX tristate "Qualcomm Atheros WCN3660/3680 support" depends on MAC80211 && HAS_DMA + select ATH_COMMON ---help--- This module adds support for wireless adapters based on Qualcomm Atheros WCN3660 and WCN3680 mobile chipsets.
drivers/net/wireless/ath/wcn36xx/main.c +34 -0
@@ -24,6 +24,12 @@ unsigned int wcn36xx_dbg_mask;module_param_named (debug_mask, wcn36xx_dbg_mask, uint,0644 );MODULE_PARM_DESC (debug_mask,"Debugging mask" ); +/* XXX: parse NVRAM */ +static struct ath_regulatory ath_reg_default = { + .current_rd =0x64 , + .power_limit =63 , +}; +#define CHAN2G (_freq, _idx) { \ .band = IEEE80211_BAND_2GHZ, \ .center_freq = (_freq), \
@@ -939,12 +945,27 @@ static int wcn36xx_platform_get_resources(struct wcn36xx *wcn,return 0 ; } +static void wcn_reg_notifier (struct wiphy *wiphy, +struct regulatory_request *request) +{ +struct ieee80211_hw *hw =wiphy_to_ieee80211_hw (wiphy); +struct wcn36xx *wcn = hw->priv; +struct ath_regulatory *reg = wcn->reg; + +ath_reg_notifier_apply (wiphy, request, reg); + +/* XXX: Set tx power, and DFS domain */ + +return ; +} +static int wcn36xx_probe (struct platform_device *pdev) {struct ieee80211_hw *hw;struct wcn36xx *wcn;int ret;u8 addr[ETH_ALEN ]; +struct ath_regulatory *reg;wcn36xx_dbg (WCN36XX_DBG_MAC ,"platform probe\n" );
@@ -971,11 +992,24 @@ static int wcn36xx_probe(struct platform_device *pdev)if (ret) goto out_wq; + wcn->reg = &ath_reg_default; + reg = wcn->reg; + ret =ath_regd_init (reg, wcn->hw->wiphy, + wcn_reg_notifier); +if (ret) + goto out_wq; +wcn36xx_init_ieee80211 (wcn); ret =ieee80211_register_hw (wcn->hw);if (ret) goto out_unmap; +if (!ath_is_world_regd (wcn->reg)) { + ret =regulatory_hint (wcn->hw->wiphy, reg->alpha2); +if (ret) + goto out_unmap; + } +return 0 ; out_unmap:
drivers/net/wireless/ath/wcn36xx/wcn36xx.h +2 -0
@@ -28,6 +28,7 @@#include "dxe.h" #include "pmc.h" #include "debug.h" +#include "../regd.h" #define WLAN_NV_FILE "wlan/prima/WCNSS_qcom_wlan_nv.bin"#define WCN36XX_AGGR_BUFFER_SIZE 64
@@ -214,6 +215,7 @@ struct wcn36xx {struct wcn36xx_dxe_mem_pool data_mem_pool;struct sk_buff *tx_ack_skb; +struct ath_regulatory *reg;#ifdef CONFIG_WCN36XX_DEBUGFS /* Debug file system entry */
Signature · 1 line
1.7.10.4
Hi Luis,
Thanx for the patch. Although there is a one small comment:
drivers/net/wireless/ath/wcn36xx/main.c static int wcn36xx_platform_get_resources(struct wcn36xx *wcn, · line 950
Quoted 3 lines
drivers/net/wireless/ath/wcn36xx/main.c +3
-0+static void wcn_reg_notifier (struct wiphy *wiphy, +struct regulatory_request *request) +{
Function should be called wcn36xx_reg_notifier not wcn_reg_notifier. Could you please change that?
Also are you concerned about this warnings?
Quoted 11 lines
Nice! I test compiled with sparse enabled and got this:
mcgrof@chalten ~/wireless-testing (git::master)$ make C=1 M=drivers/net/wireless/ath/wcn36xx/
CHECK drivers/net/wireless/ath/wcn36xx/main.c CC [M] drivers/net/wireless/ath/wcn36xx/main.o CHECK drivers/net/wireless/ath/wcn36xx/dxe.c CC [M] drivers/net/wireless/ath/wcn36xx/dxe.o CHECK drivers/net/wireless/ath/wcn36xx/txrx.c CC [M] drivers/net/wireless/ath/wcn36xx/txrx.o CHECK drivers/net/wireless/ath/wcn36xx/smd.c
Quoted 6 lines
/home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (4096 8)/home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (512 8)/home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (128 8)/home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (8 8)/home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (256 8)/home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (4096 8)
What kind of config are you using to generate this warnings?
Hi Luis,
Warnings are valid! Thanx for pointing them. Will fix and resend the patch togather with ur regdb patch+warning fix.
2013/10/6 Eugene Krasnikov <[email protected]>:
Quoted 32 lines
Hi Luis,
Thanx for the patch. Although there is a one small comment:
drivers/net/wireless/ath/wcn36xx/main.c static int wcn36xx_platform_get_resources(struct wcn36xx *wcn, · line 950
Quoted 3 lines
drivers/net/wireless/ath/wcn36xx/main.c +3
-0+static void wcn_reg_notifier (struct wiphy *wiphy, +struct regulatory_request *request) +{Function should be called
wcn36xx_reg_notifiernotwcn_reg_notifier. Could you please change that?Also are you concerned about this warnings?
Quoted 11 lines
Nice! I test compiled with sparse enabled and got this:
mcgrof@chalten ~/wireless-testing (git::master)$ make C=1 M=drivers/net/wireless/ath/wcn36xx/
CHECK drivers/net/wireless/ath/wcn36xx/main.c CC [M] drivers/net/wireless/ath/wcn36xx/main.o CHECK drivers/net/wireless/ath/wcn36xx/dxe.c CC [M] drivers/net/wireless/ath/wcn36xx/dxe.o CHECK drivers/net/wireless/ath/wcn36xx/txrx.c CC [M] drivers/net/wireless/ath/wcn36xx/txrx.o CHECK drivers/net/wireless/ath/wcn36xx/smd.cQuoted 6 lines
/home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (4096 8)/home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (512 8)/home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (128 8)/home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (8 8)/home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (256 8)/home/mcgrof/wireless-testing/arch/x86/include/asm/bitops.h:329:18: warning: invalid access past the end of 'caps' (4096 8)What kind of config are you using to generate this warnings?
Signature · 2 lines
Best regards, Eugene
Quoted 6 lines · Eugene Krasnikov
drivers/net/wireless/ath/wcn36xx/main.c static int wcn36xx_platform_get_resources(struct wcn36xx *wcn, · line 950
Quoted 3 lines
drivers/net/wireless/ath/wcn36xx/main.c +3
-0+static void wcn_reg_notifier (struct wiphy *wiphy, +struct regulatory_request *request) +{Function should be called
wcn36xx_reg_notifiernotwcn_reg_notifier. Could you please change that?
Feel free to make that change on your end :D
Luis
Hi Luis,
I looked at your patch deeper and couple of questions appeared:
1) The first line in the function ath_regd_init will execute container_of with "struct ath_common". Do not you think we can try to access wrong memory area?
2) __ath_regd_init will try to access EEPROM or at least call functions with eeprom related. It's a bit misleading because wcn36xx is not using eeprom. If possible could you please explain what is the connection between ath regd implementation and EEPROM?
Quoted 11 lines · Luis R. Rodriguez
Quoted 6 lines · Eugene Krasnikov
drivers/net/wireless/ath/wcn36xx/main.c static int wcn36xx_platform_get_resources(struct wcn36xx *wcn, · line 950
Quoted 3 lines
drivers/net/wireless/ath/wcn36xx/main.c +3
-0+static void wcn_reg_notifier (struct wiphy *wiphy, +struct regulatory_request *request) +{Function should be called
wcn36xx_reg_notifiernotwcn_reg_notifier. Could you please change that?Feel free to make that change on your end :D
Luis
Signature · 2 lines
Best regards, Eugene
Quoted 7 lines · Eugene Krasnikov
Hi Luis,
I looked at your patch deeper and couple of questions appeared:
1) The first line in the function
ath_regd_initwill executecontainer_ofwith "structath_common". Do not you think we can try to access wrong memory area?
Good catch, can you add an ath_common to the general wcn data structure and then embed the reg under it? That'd fix that.
Quoted 2 lines
2)
__ath_regd_initwill try to access EEPROM or at least call functions with eeprom related.
That's inherited from the language used on the HAL code. The HAL is no longer a HAL and we have general "hardware code". The code in that file is more than anything now just database specific information, as such routines like ath_regd_get_eepromRD() could be renamed to reflect they are simply accessing regulatory information from the card.
Quoted 3 lines
It's a bit misleading because
wcn36xx is not using eeprom. If possible could you please explain what is the connection between ath regd implementation and EEPROM?
Indeed, agreed. The way to properly use regulatory on the wcn driver will be parse the nvram and populate the struct ath_regulatory appropriately. This then makes the EEPROM verbiage inappropriate and do welcome such changes reflected on regd.c but don't see them required for wcn to use them. This can be made as further clarifications once the wcn driver gets merged.
Luis
PATCH 1/1 wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware
This is a mac80211 driver for Qualcomm WCN3660/WCN3680 devices. So far WCN3660/WCN3680 is available only on MSM platform.
Firmware can be found here:
https://www.codeaurora.org/cgit/external/hisense/platform/vendor/qcom-opensource/wlan/prima/tree/firmware_bin?h=8130_CS
Wiki page is available here:
http://wireless.kernel.org/en/users/Drivers/wcn36xx
A lot people made a contribution to this driver. Here is the list in alphabetical order:
Eugene Krasnikov <[email protected]>
Kalle Valo <[email protected]>
Olof Johansson <[email protected]>
Pontus Fuchs <[email protected]>
Yanbo Li <[email protected]>
--- MAINTAINERS | 8 + drivers/net/wireless/ath/Kconfig | 1 + drivers/net/wireless/ath/Makefile | 1 + drivers/net/wireless/ath/wcn36xx/Kconfig | 16 + drivers/net/wireless/ath/wcn36xx/Makefile | 7 + drivers/net/wireless/ath/wcn36xx/debug.c | 188 ++ drivers/net/wireless/ath/wcn36xx/debug.h | 49 + drivers/net/wireless/ath/wcn36xx/dxe.c | 805 +++++ drivers/net/wireless/ath/wcn36xx/dxe.h | 284 ++ drivers/net/wireless/ath/wcn36xx/hal.h | 4657 ++++++++++++++++++++++++++++ drivers/net/wireless/ath/wcn36xx/main.c | 1036 +++++++ drivers/net/wireless/ath/wcn36xx/pmc.c | 62 + drivers/net/wireless/ath/wcn36xx/pmc.h | 33 + drivers/net/wireless/ath/wcn36xx/smd.c | 2126 +++++++++++++ drivers/net/wireless/ath/wcn36xx/smd.h | 127 + drivers/net/wireless/ath/wcn36xx/txrx.c | 284 ++ drivers/net/wireless/ath/wcn36xx/txrx.h | 160 + drivers/net/wireless/ath/wcn36xx/wcn36xx.h | 238 ++ 18 files changed, 10082 insertions(+) create mode 100644 drivers/net/wireless/ath/wcn36xx/Kconfig create mode 100644 drivers/net/wireless/ath/wcn36xx/Makefile create mode 100644 drivers/net/wireless/ath/wcn36xx/debug.c create mode 100644 drivers/net/wireless/ath/wcn36xx/debug.h create mode 100644 drivers/net/wireless/ath/wcn36xx/dxe.c create mode 100644 drivers/net/wireless/ath/wcn36xx/dxe.h create mode 100644 drivers/net/wireless/ath/wcn36xx/hal.h create mode 100644 drivers/net/wireless/ath/wcn36xx/main.c create mode 100644 drivers/net/wireless/ath/wcn36xx/pmc.c create mode 100644 drivers/net/wireless/ath/wcn36xx/pmc.h create mode 100644 drivers/net/wireless/ath/wcn36xx/smd.c create mode 100644 drivers/net/wireless/ath/wcn36xx/smd.h create mode 100644 drivers/net/wireless/ath/wcn36xx/txrx.c create mode 100644 drivers/net/wireless/ath/wcn36xx/txrx.h create mode 100644 drivers/net/wireless/ath/wcn36xx/wcn36xx.h
MAINTAINERS +8 -0
@@ -6745,6 +6745,14 @@ L: [email protected] S: Supported F: arch/hexagon/ +QUALCOMM WCN36XX WIRELESS DRIVER +M: Eugene Krasnikov <[email protected]> +L: [email protected] +W: http://wireless.kernel.org/en/users/Drivers/wcn36xx +T: git git://github.com/KrasnikovEugene/wcn36xx.git +S: Supported +F: drivers/net/wireless/ath/wcn36xx/ + QUICKCAM PARALLEL PORT WEBCAMS M: Hans Verkuil <[email protected]> L: [email protected]
drivers/net/wireless/ath/Kconfig +1 -0
@@ -32,5 +32,6 @@ source "drivers/net/wireless/ath/ath6kl/Kconfig" source "drivers/net/wireless/ath/ar5523/Kconfig" source "drivers/net/wireless/ath/wil6210/Kconfig" source "drivers/net/wireless/ath/ath10k/Kconfig" +source "drivers/net/wireless/ath/wcn36xx/Kconfig" endif
drivers/net/wireless/ath/Makefile +1 -0
@@ -5,6 +5,7 @@ obj-$(CONFIG_ATH6KL) += ath6kl/ obj-$(CONFIG_AR5523) += ar5523/ obj-$(CONFIG_WIL6210) += wil6210/ obj-$(CONFIG_ATH10K) += ath10k/ +obj-$(CONFIG_WCN36XX) += wcn36xx/ obj-$(CONFIG_ATH_COMMON) += ath.o
drivers/net/wireless/ath/wcn36xx/Kconfig new file +16 -0
@@ -0,0 +1,16 @@ +config WCN36XX + tristate "Qualcomm Atheros WCN3660/3680 support" + depends on MAC80211 && HAS_DMA + ---help--- + This module adds support for wireless adapters based on + Qualcomm Atheros WCN3660 and WCN3680 mobile chipsets. + + If you choose to build a module, it'll be called wcn36xx. + +config WCN36XX_DEBUGFS + bool "WCN36XX debugfs support" + depends on WCN36XX + ---help--- + Enabled debugfs support + + If unsure, say Y to make it easier to debug problems.
drivers/net/wireless/ath/wcn36xx/Makefile new file +7 -0
@@ -0,0 +1,7 @@ +obj-$(CONFIG_WCN36XX) := wcn36xx.o +wcn36xx-y += main.o \ + dxe.o \ + txrx.o \ + smd.o \ + pmc.o \ + debug.o
drivers/net/wireless/ath/wcn36xx/debug.c new file +188 -0
188 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/debug.h new file +49 -0
49 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/dxe.c new file +805 -0
805 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/dxe.h new file +284 -0
284 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/hal.h new file +4657 -0
1,624 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/main.c new file +1036 -0
1,036 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/pmc.c new file +62 -0
62 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/pmc.h new file +33 -0
Lines of this file are not shown. View the raw message.
drivers/net/wireless/ath/wcn36xx/smd.c new file +2126 -0
2,126 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/smd.h new file +127 -0
127 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/txrx.c new file +284 -0
284 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/txrx.h new file +160 -0
160 lines not on this page · raw message
drivers/net/wireless/ath/wcn36xx/wcn36xx.h new file +238 -0
238 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
1.8.1.2
Part of the diff is not shown here. View the raw message.
Hi John,
This is the final version of wcn36xx driver with sparce/smatch warnings fixed. Please let me know if there are any problems.
Quoted 10,262 lines · Eugene Krasnikov
This is a mac80211 driver for Qualcomm WCN3660/WCN3680 devices. So far WCN3660/WCN3680 is available only on MSM platform.
Firmware can be found here:
https://www.codeaurora.org/cgit/external/hisense/platform/vendor/qcom-opensource/wlan/prima/tree/firmware_bin?h=8130_CSWiki page is available here:
http://wireless.kernel.org/en/users/Drivers/wcn36xxA lot people made a contribution to this driver. Here is the list in alphabetical order:
Eugene Krasnikov <[email protected]>
Kalle Valo <[email protected]>
Olof Johansson <[email protected]>
Pontus Fuchs <[email protected]>
Yanbo Li <[email protected]>Signed-off-by Eugene Krasnikov <[email protected]>--- MAINTAINERS | 8 + drivers/net/wireless/ath/Kconfig | 1 + drivers/net/wireless/ath/Makefile | 1 + drivers/net/wireless/ath/wcn36xx/Kconfig | 16 + drivers/net/wireless/ath/wcn36xx/Makefile | 7 + drivers/net/wireless/ath/wcn36xx/debug.c | 188 ++ drivers/net/wireless/ath/wcn36xx/debug.h | 49 + drivers/net/wireless/ath/wcn36xx/dxe.c | 805 +++++ drivers/net/wireless/ath/wcn36xx/dxe.h | 284 ++ drivers/net/wireless/ath/wcn36xx/hal.h | 4657 ++++++++++++++++++++++++++++ drivers/net/wireless/ath/wcn36xx/main.c | 1036 +++++++ drivers/net/wireless/ath/wcn36xx/pmc.c | 62 + drivers/net/wireless/ath/wcn36xx/pmc.h | 33 + drivers/net/wireless/ath/wcn36xx/smd.c | 2126 +++++++++++++ drivers/net/wireless/ath/wcn36xx/smd.h | 127 + drivers/net/wireless/ath/wcn36xx/txrx.c | 284 ++ drivers/net/wireless/ath/wcn36xx/txrx.h | 160 + drivers/net/wireless/ath/wcn36xx/wcn36xx.h | 238 ++ 18 files changed, 10082 insertions(+) create mode 100644 drivers/net/wireless/ath/wcn36xx/Kconfig create mode 100644 drivers/net/wireless/ath/wcn36xx/Makefile create mode 100644 drivers/net/wireless/ath/wcn36xx/debug.c create mode 100644 drivers/net/wireless/ath/wcn36xx/debug.h create mode 100644 drivers/net/wireless/ath/wcn36xx/dxe.c create mode 100644 drivers/net/wireless/ath/wcn36xx/dxe.h create mode 100644 drivers/net/wireless/ath/wcn36xx/hal.h create mode 100644 drivers/net/wireless/ath/wcn36xx/main.c create mode 100644 drivers/net/wireless/ath/wcn36xx/pmc.c create mode 100644 drivers/net/wireless/ath/wcn36xx/pmc.h create mode 100644 drivers/net/wireless/ath/wcn36xx/smd.c create mode 100644 drivers/net/wireless/ath/wcn36xx/smd.h create mode 100644 drivers/net/wireless/ath/wcn36xx/txrx.c create mode 100644 drivers/net/wireless/ath/wcn36xx/txrx.h create mode 100644 drivers/net/wireless/ath/wcn36xx/wcn36xx.hMAINTAINERS +8
-0@@ -6745,6 +6745,14 @@ L: [email protected] S: Supported F: arch/hexagon/ +QUALCOMM WCN36XX WIRELESS DRIVER +M: Eugene Krasnikov <[email protected]> +L: [email protected] +W: http://wireless.kernel.org/en/users/Drivers/wcn36xx +T: git git://github.com/KrasnikovEugene/wcn36xx.git +S: Supported +F: drivers/net/wireless/ath/wcn36xx/ + QUICKCAM PARALLEL PORT WEBCAMS M: Hans Verkuil <[email protected]> L: [email protected]drivers/net/wireless/ath/Kconfig +1
-0@@ -32,5 +32,6 @@ source "drivers/net/wireless/ath/ath6kl/Kconfig" source "drivers/net/wireless/ath/ar5523/Kconfig" source "drivers/net/wireless/ath/wil6210/Kconfig" source "drivers/net/wireless/ath/ath10k/Kconfig" +source "drivers/net/wireless/ath/wcn36xx/Kconfig" endifdrivers/net/wireless/ath/Makefile +1
-0@@ -5,6 +5,7 @@ obj-$(CONFIG_ATH6KL) += ath6kl/ obj-$(CONFIG_AR5523) += ar5523/ obj-$(CONFIG_WIL6210) += wil6210/ obj-$(CONFIG_ATH10K) += ath10k/ +obj-$(CONFIG_WCN36XX) += wcn36xx/ obj-$(CONFIG_ATH_COMMON) += ath.odrivers/net/wireless/ath/wcn36xx/Kconfig new file +16
-0@@ -0,0 +1,16 @@ +config WCN36XX + tristate "Qualcomm Atheros WCN3660/3680 support" + depends on MAC80211 && HAS_DMA + ---help--- + This module adds support for wireless adapters based on + Qualcomm Atheros WCN3660 and WCN3680 mobile chipsets. + + If you choose to build a module, it'll be called wcn36xx. + +config WCN36XX_DEBUGFS + bool "WCN36XX debugfs support" + depends on WCN36XX + ---help--- + Enabled debugfs support + + If unsure, say Y to make it easier to debug problems.drivers/net/wireless/ath/wcn36xx/Makefile new file +7
-0@@ -0,0 +1,7 @@ +obj-$(CONFIG_WCN36XX) := wcn36xx.o +wcn36xx-y += main.o \ + dxe.o \ + txrx.o \ + smd.o \ + pmc.o \ + debug.odrivers/net/wireless/ath/wcn36xx/debug.c new file +188
-0@@ -0,0 +1,188 @@ +/* +* Copyright (c) 2013 Eugene Krasnikov <[email protected]> +* +* Permission to use, copy, modify, and/or distribute this software for any +* purpose with or without fee is hereby granted, provided that the above +* copyright notice and this permission notice appear in all copies. +* +* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES +* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF +* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY +* SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES +* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION +* OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN +* CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. +*/ + +#define pr_fmt (fmt) KBUILD_MODNAME ": " fmt + +#include <linux/debugfs.h> +#include <linux/uaccess.h> +#include "wcn36xx.h" +#include "debug.h" +#include "pmc.h" + +#ifdef CONFIG_WCN36XX_DEBUGFS + +static int wcn36xx_debugfs_open (struct inode *inode,struct file *file) +{ + file->private_data = inode->i_private; + +return 0 ; +} + +static ssize_t read_file_bool_bmps (struct file *file,char __user *user_buf, +size_t count,loff_t *ppos) +{ +struct wcn36xx *wcn = file->private_data; +struct wcn36xx_vif *vif_priv =NULL ; +struct ieee80211_vif *vif =NULL ; +char buf[3 ]; + +list_for_each_entry (vif_priv, &wcn->vif_list, list) { + vif =container_of ((void *)vif_priv, + struct ieee80211_vif, + drv_priv); +if (NL80211_IFTYPE_STATION == vif->type) { +if (vif_priv->pw_state ==WCN36XX_BMPS ) + buf[0 ] ='1' ; +else + buf[0 ] ='0' ; +break ; + } + } + buf[1 ] ='\n' ; + buf[2 ] =0x00 ; + +return simple_read_from_buffer (user_buf, count, ppos, buf,2 ); +} + +static ssize_t write_file_bool_bmps (struct file *file, +const char __user *user_buf, +size_t count,loff_t *ppos) +{ +struct wcn36xx *wcn = file->private_data; +struct wcn36xx_vif *vif_priv =NULL ; +struct ieee80211_vif *vif =NULL ; + +char buf[32 ]; +int buf_size; + + buf_size =min (count, (sizeof (buf)-1 )); +if (copy_from_user (buf, user_buf, buf_size)) +return -EFAULT ; + +switch (buf[0 ]) { +case 'y' : +case 'Y' : +case '1' : +list_for_each_entry (vif_priv, &wcn->vif_list, list) { + vif =container_of ((void *)vif_priv, + struct ieee80211_vif, + drv_priv); +if (NL80211_IFTYPE_STATION == vif->type) { +wcn36xx_enable_keep_alive_null_packet (wcn, vif); +wcn36xx_pmc_enter_bmps_state (wcn, vif); + } + } +break ; +case 'n' : +case 'N' : +case '0' : +list_for_each_entry (vif_priv, &wcn->vif_list, list) { + vif =container_of ((void *)vif_priv, + struct ieee80211_vif, + drv_priv); +if (NL80211_IFTYPE_STATION == vif->type) +wcn36xx_pmc_exit_bmps_state (wcn, vif); + } +break ; + } + +return count; +} + +static const struct file_operations fops_wcn36xx_bmps = { + .open = wcn36xx_debugfs_open, + .read = read_file_bool_bmps, + .write = write_file_bool_bmps, +}; + +static ssize_t write_file_dump (struct file *file, +const char __user *user_buf, +size_t count,loff_t *ppos) +{ +struct wcn36xx *wcn = file->private_data; +char buf[255 ], *tmp; +int buf_size; +u32 arg[WCN36xx_MAX_DUMP_ARGS]; +int i; + +memset (buf,0 ,sizeof (buf)); +memset (arg,0 ,sizeof (arg)); + + buf_size =min (count, (sizeof (buf) -1 )); +if (copy_from_user (buf, user_buf, buf_size)) +return -EFAULT ; + + tmp = buf; + +for (i =0 ; i < WCN36xx_MAX_DUMP_ARGS; i++) { +char *begin; + begin =strsep (&tmp," " ); +if (begin ==NULL ) +break ; + +if (kstrtoul (begin,0 , (unsigned long *)(arg + i)) !=0 ) +break ; + } + +wcn36xx_info ("DUMP args is %d %d %d %d %d\n" , arg[0 ], arg[1 ], arg[2 ], + arg[3 ], arg[4 ]); +wcn36xx_smd_dump_cmd_req (wcn, arg[0 ], arg[1 ], arg[2 ], arg[3 ], arg[4 ]); + +return count; +} + +static const struct file_operations fops_wcn36xx_dump = { + .open = wcn36xx_debugfs_open, + .write = write_file_dump, +}; + +#define ADD_FILE (name, mode, fop, priv_data) \ + do { \ + struct dentry *d; \ + d = debugfs_create_file(__stringify(name), \ + mode, dfs->rootdir, \ + priv_data, fop); \ + dfs->file_##name.dentry = d; \ + if (IS_ERR(d)) { \ + wcn36xx_warn("Create the debugfs entry failed");\ + dfs->file_##name.dentry = NULL; \ + } \ + } while (0) + + +void wcn36xx_debugfs_init (struct wcn36xx *wcn) +{ +struct wcn36xx_dfs_entry *dfs = &wcn->dfs; + + dfs->rootdir =debugfs_create_dir (KBUILD_MODNAME , + wcn->hw->wiphy->debugfsdir); +if (IS_ERR (dfs->rootdir)) { +wcn36xx_warn ("Create the debugfs failed\n" ); + dfs->rootdir =NULL ; + } + +ADD_FILE (bmps_switcher,S_IRUSR |S_IWUSR , + &fops_wcn36xx_bmps, wcn); +ADD_FILE (dump,S_IWUSR , &fops_wcn36xx_dump, wcn); +} + +void wcn36xx_debugfs_exit (struct wcn36xx *wcn) +{ +struct wcn36xx_dfs_entry *dfs = &wcn->dfs; +debugfs_remove_recursive (dfs->rootdir); +} + +#endif /* CONFIG_WCN36XX_DEBUGFS */ drivers/net/wireless/ath/wcn36xx/debug.h new file +49
-0@@ -0,0 +1,49 @@ +/* +* Copyright (c) 2013 Eugene Krasnikov <[email protected]> +* +* Permission to use, copy, modify, and/or distribute this software for any +* purpose with or without fee is hereby granted, provided that the above +* copyright notice and this permission notice appear in all copies. +* +* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES +* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF +* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY +* SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES +* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION +* OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN +* CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. +*/ + +#ifndef _WCN36XX_DEBUG_H_ +#define _WCN36XX_DEBUG_H_ + +#include <linux/kernel.h> + +#define WCN36xx_MAX_DUMP_ARGS 5 + +#ifdef CONFIG_WCN36XX_DEBUGFS +struct wcn36xx_dfs_file { +struct dentry *dentry; +u32 value; +}; + +struct wcn36xx_dfs_entry { +struct dentry *rootdir; +struct wcn36xx_dfs_file file_bmps_switcher; +struct wcn36xx_dfs_file file_dump; +}; + +void wcn36xx_debugfs_init (struct wcn36xx *wcn); +void wcn36xx_debugfs_exit (struct wcn36xx *wcn); + +#else +static inline void wcn36xx_debugfs_init (struct wcn36xx *wcn) +{ +} +static inline void wcn36xx_debugfs_exit (struct wcn36xx *wcn) +{ +} + +#endif /* CONFIG_WCN36XX_DEBUGFS */ + +#endif /* _WCN36XX_DEBUG_H_ */ drivers/net/wireless/ath/wcn36xx/dxe.c new file +805
-0@@ -0,0 +1,805 @@ +/* +* Copyright (c) 2013 Eugene Krasnikov <[email protected]> +* +* Permission to use, copy, modify, and/or distribute this software for any +* purpose with or without fee is hereby granted, provided that the above +* copyright notice and this permission notice appear in all copies. +* +* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES +* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF +* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY +* SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES +* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION +* OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN +* CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. +*/ + +/* DXE - DMA transfer engine +* we have 2 channels(High prio and Low prio) for TX and 2 channels for RX. +* through low channels data packets are transfered +* through high channels managment packets are transfered +*/ + +#define pr_fmt (fmt) KBUILD_MODNAME ": " fmt + +#include <linux/interrupt.h> +#include "wcn36xx.h" +#include "txrx.h" + +void *wcn36xx_dxe_get_next_bd (struct wcn36xx *wcn,bool is_low) +{ +struct wcn36xx_dxe_ch *ch = is_low ? + &wcn->dxe_tx_l_ch : + &wcn->dxe_tx_h_ch; + +return ch->head_blk_ctl->bd_cpu_addr; +} + +static void wcn36xx_dxe_write_register (struct wcn36xx *wcn,int addr,int data) +{ +wcn36xx_dbg (WCN36XX_DBG_DXE , +"wcn36xx_dxe_write_register: addr=%x, data=%x\n" , + addr, data); + +writel (data, wcn->mmio + addr); +} + +static void wcn36xx_dxe_read_register (struct wcn36xx *wcn,int addr,int *data) +{ + *data =readl (wcn->mmio + addr); + +wcn36xx_dbg (WCN36XX_DBG_DXE , +"wcn36xx_dxe_read_register: addr=%x, data=%x\n" , + addr, *data); +} + +static void wcn36xx_dxe_free_ctl_block (struct wcn36xx_dxe_ch *ch) +{ +struct wcn36xx_dxe_ctl *ctl = ch->head_blk_ctl, *next; +int i; + +for (i =0 ; i < ch->desc_num && ctl; i++) { + next = ctl->next; +kfree (ctl); + ctl = next; + } +} + +static int wcn36xx_dxe_allocate_ctl_block (struct wcn36xx_dxe_ch *ch) +{ +struct wcn36xx_dxe_ctl *prev_ctl =NULL ; +struct wcn36xx_dxe_ctl *cur_ctl =NULL ; +int i; + +for (i =0 ; i < ch->desc_num; i++) { + cur_ctl =kzalloc (sizeof (*cur_ctl),GFP_KERNEL ); +if (!cur_ctl) + goto out_fail; + + cur_ctl->ctl_blk_order = i; +if (i ==0 ) { + ch->head_blk_ctl = cur_ctl; + ch->tail_blk_ctl = cur_ctl; + }else if (ch->desc_num -1 == i) { + prev_ctl->next = cur_ctl; + cur_ctl->next = ch->head_blk_ctl; + }else { + prev_ctl->next = cur_ctl; + } + prev_ctl = cur_ctl; + } + +return 0 ; + +out_fail: +wcn36xx_dxe_free_ctl_block (ch); +return -ENOMEM ; +} + +int wcn36xx_dxe_alloc_ctl_blks (struct wcn36xx *wcn) +{ +int ret; + + wcn->dxe_tx_l_ch.ch_type =WCN36XX_DXE_CH_TX_L ; + wcn->dxe_tx_h_ch.ch_type =WCN36XX_DXE_CH_TX_H ; + wcn->dxe_rx_l_ch.ch_type =WCN36XX_DXE_CH_RX_L ; + wcn->dxe_rx_h_ch.ch_type =WCN36XX_DXE_CH_RX_H ; + + wcn->dxe_tx_l_ch.desc_num =WCN36XX_DXE_CH_DESC_NUMB_TX_L ; + wcn->dxe_tx_h_ch.desc_num =WCN36XX_DXE_CH_DESC_NUMB_TX_H ; + wcn->dxe_rx_l_ch.desc_num =WCN36XX_DXE_CH_DESC_NUMB_RX_L ; + wcn->dxe_rx_h_ch.desc_num =WCN36XX_DXE_CH_DESC_NUMB_RX_H ; + + wcn->dxe_tx_l_ch.dxe_wq =WCN36XX_DXE_WQ_TX_L ; + wcn->dxe_tx_h_ch.dxe_wq =WCN36XX_DXE_WQ_TX_H ; + + wcn->dxe_tx_l_ch.ctrl_bd =WCN36XX_DXE_CTRL_TX_L_BD ; + wcn->dxe_tx_h_ch.ctrl_bd =WCN36XX_DXE_CTRL_TX_H_BD ; + + wcn->dxe_tx_l_ch.ctrl_skb =WCN36XX_DXE_CTRL_TX_L_SKB ; + wcn->dxe_tx_h_ch.ctrl_skb =WCN36XX_DXE_CTRL_TX_H_SKB ; + + wcn->dxe_tx_l_ch.reg_ctrl =WCN36XX_DXE_REG_CTL_TX_L ; + wcn->dxe_tx_h_ch.reg_ctrl =WCN36XX_DXE_REG_CTL_TX_H ; + + wcn->dxe_tx_l_ch.def_ctrl =WCN36XX_DXE_CH_DEFAULT_CTL_TX_L ; + wcn->dxe_tx_h_ch.def_ctrl =WCN36XX_DXE_CH_DEFAULT_CTL_TX_H ; + +/* DXE control block allocation */ + ret =wcn36xx_dxe_allocate_ctl_block (&wcn->dxe_tx_l_ch); +if (ret) + goto out_err; + ret =wcn36xx_dxe_allocate_ctl_block (&wcn->dxe_tx_h_ch); +if (ret) + goto out_err; + ret =wcn36xx_dxe_allocate_ctl_block (&wcn->dxe_rx_l_ch); +if (ret) + goto out_err; + ret =wcn36xx_dxe_allocate_ctl_block (&wcn->dxe_rx_h_ch); +if (ret) + goto out_err; + +/* Initialize SMSM state Clear TX Enable RING EMPTY STATE */ + ret = wcn->ctrl_ops->smsm_change_state ( +WCN36XX_SMSM_WLAN_TX_ENABLE , +WCN36XX_SMSM_WLAN_TX_RINGS_EMPTY ); + +return 0 ; + +out_err: +wcn36xx_err ("Failed to allocate DXE control blocks\n" ); +wcn36xx_dxe_free_ctl_blks (wcn); +return -ENOMEM ; +} + +void wcn36xx_dxe_free_ctl_blks (struct wcn36xx *wcn) +{ +wcn36xx_dxe_free_ctl_block (&wcn->dxe_tx_l_ch); +wcn36xx_dxe_free_ctl_block (&wcn->dxe_tx_h_ch); +wcn36xx_dxe_free_ctl_block (&wcn->dxe_rx_l_ch); +wcn36xx_dxe_free_ctl_block (&wcn->dxe_rx_h_ch); +} + +static int wcn36xx_dxe_init_descs (struct wcn36xx_dxe_ch *wcn_ch) +{ +struct wcn36xx_dxe_desc *cur_dxe =NULL ; +struct wcn36xx_dxe_desc *prev_dxe =NULL ; +struct wcn36xx_dxe_ctl *cur_ctl =NULL ; +size_t size; +int i; + + size = wcn_ch->desc_num *sizeof (struct wcn36xx_dxe_desc ); + wcn_ch->cpu_addr =dma_alloc_coherent (NULL , size, &wcn_ch->dma_addr, +GFP_KERNEL ); +if (!wcn_ch->cpu_addr) +return -ENOMEM ; + +memset (wcn_ch->cpu_addr,0 , size); + + cur_dxe = (struct wcn36xx_dxe_desc *)wcn_ch->cpu_addr; + cur_ctl = wcn_ch->head_blk_ctl; + +for (i =0 ; i < wcn_ch->desc_num; i++) { + cur_ctl->desc = cur_dxe; + cur_ctl->desc_phy_addr = wcn_ch->dma_addr + + i *sizeof (struct wcn36xx_dxe_desc ); + +switch (wcn_ch->ch_type) { +case WCN36XX_DXE_CH_TX_L : + cur_dxe->ctrl =WCN36XX_DXE_CTRL_TX_L ; + cur_dxe->dst_addr_l =WCN36XX_DXE_WQ_TX_L ; +break ; +case WCN36XX_DXE_CH_TX_H : + cur_dxe->ctrl =WCN36XX_DXE_CTRL_TX_H ; + cur_dxe->dst_addr_l =WCN36XX_DXE_WQ_TX_H ; +break ; +case WCN36XX_DXE_CH_RX_L : + cur_dxe->ctrl =WCN36XX_DXE_CTRL_RX_L ; + cur_dxe->src_addr_l =WCN36XX_DXE_WQ_RX_L ; +break ; +case WCN36XX_DXE_CH_RX_H : + cur_dxe->ctrl =WCN36XX_DXE_CTRL_RX_H ; + cur_dxe->src_addr_l =WCN36XX_DXE_WQ_RX_H ; +break ; + } +if (0 == i) { + cur_dxe->phy_next_l =0 ; + }else if ((0 < i) && (i < wcn_ch->desc_num -1 )) { + prev_dxe->phy_next_l = + cur_ctl->desc_phy_addr; + }else if (i == (wcn_ch->desc_num -1 )) { + prev_dxe->phy_next_l = + cur_ctl->desc_phy_addr; + cur_dxe->phy_next_l = + wcn_ch->head_blk_ctl->desc_phy_addr; + } + cur_ctl = cur_ctl->next; + prev_dxe = cur_dxe; + cur_dxe++; + } + +return 0 ; +} + +static void wcn36xx_dxe_init_tx_bd (struct wcn36xx_dxe_ch *ch, +struct wcn36xx_dxe_mem_pool *pool) +{ +int i, chunk_size = pool->chunk_size; +dma_addr_t bd_phy_addr = pool->phy_addr; +void *bd_cpu_addr = pool->virt_addr; +struct wcn36xx_dxe_ctl *cur = ch->head_blk_ctl; + +for (i =0 ; i < ch->desc_num; i++) { +/* Only every second dxe needs a bd pointer, +the other will point to the skb data */ +if (!(i &1 )) { + cur->bd_phy_addr = bd_phy_addr; + cur->bd_cpu_addr = bd_cpu_addr; + bd_phy_addr += chunk_size; + bd_cpu_addr += chunk_size; + }else { + cur->bd_phy_addr =0 ; + cur->bd_cpu_addr =NULL ; + } + cur = cur->next; + } +} + +static int wcn36xx_dxe_enable_ch_int (struct wcn36xx *wcn,u16 wcn_ch) +{ +int reg_data =0 ; + +wcn36xx_dxe_read_register (wcn, +WCN36XX_DXE_INT_MASK_REG , + ®_data); + + reg_data |= wcn_ch; + +wcn36xx_dxe_write_register (wcn, +WCN36XX_DXE_INT_MASK_REG , + (int )reg_data); +return 0 ; +} + +static int wcn36xx_dxe_fill_skb (struct wcn36xx_dxe_ctl *ctl) +{ +struct wcn36xx_dxe_desc *dxe = ctl->desc; +struct sk_buff *skb; + + skb =alloc_skb (WCN36XX_PKT_SIZE ,GFP_ATOMIC ); +if (skb ==NULL ) +return -ENOMEM ; + + dxe->dst_addr_l =dma_map_single (NULL , +skb_tail_pointer (skb), +WCN36XX_PKT_SIZE , +DMA_FROM_DEVICE ); + ctl->skb = skb; + +return 0 ; +} + +static int wcn36xx_dxe_ch_alloc_skb (struct wcn36xx *wcn, +struct wcn36xx_dxe_ch *wcn_ch) +{ +int i; +struct wcn36xx_dxe_ctl *cur_ctl =NULL ; + + cur_ctl = wcn_ch->head_blk_ctl; + +for (i =0 ; i < wcn_ch->desc_num; i++) { +wcn36xx_dxe_fill_skb (cur_ctl); + cur_ctl = cur_ctl->next; + } + +return 0 ; +} + +static void wcn36xx_dxe_ch_free_skbs (struct wcn36xx *wcn, +struct wcn36xx_dxe_ch *wcn_ch) +{ +struct wcn36xx_dxe_ctl *cur = wcn_ch->head_blk_ctl; +int i; + +for (i =0 ; i < wcn_ch->desc_num; i++) { +kfree_skb (cur->skb); + cur = cur->next; + } +} + +void wcn36xx_dxe_tx_ack_ind (struct wcn36xx *wcn,u32 status) +{ +struct ieee80211_tx_info *info; +struct sk_buff *skb; +unsigned long flags; + +spin_lock_irqsave (&wcn->dxe_lock, flags); + skb = wcn->tx_ack_skb; + wcn->tx_ack_skb =NULL ; +spin_unlock_irqrestore (&wcn->dxe_lock, flags); + +if (!skb) { +wcn36xx_warn ("Spurious TX complete indication\n" ); +return ; + } + + info =IEEE80211_SKB_CB (skb); + +if (status ==1 ) + info->flags |=IEEE80211_TX_STAT_ACK ; + +wcn36xx_dbg (WCN36XX_DBG_DXE ,"dxe tx ack status: %d\n" , status); + +ieee80211_tx_status_irqsafe (wcn->hw, skb); +ieee80211_wake_queues (wcn->hw); +} + +static void reap_tx_dxes (struct wcn36xx *wcn,struct wcn36xx_dxe_ch *ch) +{ +struct wcn36xx_dxe_ctl *ctl = ch->tail_blk_ctl; +struct ieee80211_tx_info *info; +unsigned long flags; + +/* +* Make at least one loop of do-while because in case ring is +* completely full head and tail are pointing to the same element +* and while-do will not make any cycles. +*/ +do { +if (ctl->skb) { +dma_unmap_single (NULL , ctl->desc->src_addr_l, + ctl->skb->len,DMA_TO_DEVICE ); + info =IEEE80211_SKB_CB (ctl->skb); +if (!(info->flags &IEEE80211_TX_CTL_REQ_TX_STATUS )) { +/* Keep frame until TX status comes */ +ieee80211_free_txskb (wcn->hw, ctl->skb); + } +spin_lock_irqsave (&ctl->skb_lock, flags); +if (wcn->queues_stopped) { + wcn->queues_stopped = false; +ieee80211_wake_queues (wcn->hw); + } +spin_unlock_irqrestore (&ctl->skb_lock, flags); + + ctl->skb =NULL ; + } + ctl = ctl->next; + }while (ctl != ch->head_blk_ctl && + !(ctl->desc->ctrl &WCN36XX_DXE_CTRL_VALID_MASK )); + + ch->tail_blk_ctl = ctl; +} + +static irqreturn_t wcn36xx_irq_tx_complete (int irq,void *dev) +{ +struct wcn36xx *wcn = (struct wcn36xx *)dev; +int int_src, int_reason; + +wcn36xx_dxe_read_register (wcn,WCN36XX_DXE_INT_SRC_RAW_REG , &int_src); + +if (int_src &WCN36XX_INT_MASK_CHAN_TX_H ) { +wcn36xx_dxe_read_register (wcn, +WCN36XX_DXE_CH_STATUS_REG_ADDR_TX_H , + &int_reason); + +/* TODO: Check int_reason */ + +wcn36xx_dxe_write_register (wcn, +WCN36XX_DXE_0_INT_CLR , +WCN36XX_INT_MASK_CHAN_TX_H ); + +wcn36xx_dxe_write_register (wcn,WCN36XX_DXE_0_INT_ED_CLR , +WCN36XX_INT_MASK_CHAN_TX_H ); +wcn36xx_dbg (WCN36XX_DBG_DXE ,"dxe tx ready high\n" ); +reap_tx_dxes (wcn, &wcn->dxe_tx_h_ch); + } + +if (int_src &WCN36XX_INT_MASK_CHAN_TX_L ) { +wcn36xx_dxe_read_register (wcn, +WCN36XX_DXE_CH_STATUS_REG_ADDR_TX_L , + &int_reason); +/* TODO: Check int_reason */ + +wcn36xx_dxe_write_register (wcn, +WCN36XX_DXE_0_INT_CLR , +WCN36XX_INT_MASK_CHAN_TX_L ); + +wcn36xx_dxe_write_register (wcn,WCN36XX_DXE_0_INT_ED_CLR , +WCN36XX_INT_MASK_CHAN_TX_L ); +wcn36xx_dbg (WCN36XX_DBG_DXE ,"dxe tx ready low\n" ); +reap_tx_dxes (wcn, &wcn->dxe_tx_l_ch); + } + +return IRQ_HANDLED ; +} + +static irqreturn_t wcn36xx_irq_rx_ready (int irq,void *dev) +{ +struct wcn36xx *wcn = (struct wcn36xx *)dev; + +disable_irq_nosync (wcn->rx_irq); +wcn36xx_dxe_rx_frame (wcn); +enable_irq (wcn->rx_irq); +return IRQ_HANDLED ; +} + +static int wcn36xx_dxe_request_irqs (struct wcn36xx *wcn) +{ +int ret; + + ret =request_irq (wcn->tx_irq, wcn36xx_irq_tx_complete, +IRQF_TRIGGER_HIGH ,"wcn36xx_tx" , wcn); +if (ret) { +wcn36xx_err ("failed to alloc tx irq\n" ); + goto out_err; + } + + ret =request_irq (wcn->rx_irq, wcn36xx_irq_rx_ready,IRQF_TRIGGER_HIGH , +"wcn36xx_rx" , wcn); +if (ret) { +wcn36xx_err ("failed to alloc rx irq\n" ); + goto out_txirq; + } + +enable_irq_wake (wcn->rx_irq); + +return 0 ; + +out_txirq: +free_irq (wcn->tx_irq, wcn); +out_err: +return ret; + +} + +static int wcn36xx_rx_handle_packets (struct wcn36xx *wcn, +struct wcn36xx_dxe_ch *ch) +{ +struct wcn36xx_dxe_ctl *ctl = ch->head_blk_ctl; +struct wcn36xx_dxe_desc *dxe = ctl->desc; +dma_addr_t dma_addr; +struct sk_buff *skb; + +while (!(dxe->ctrl &WCN36XX_DXE_CTRL_VALID_MASK )) { + skb = ctl->skb; + dma_addr = dxe->dst_addr_l; +wcn36xx_dxe_fill_skb (ctl); + +switch (ch->ch_type) { +case WCN36XX_DXE_CH_RX_L : + dxe->ctrl =WCN36XX_DXE_CTRL_RX_L ; +wcn36xx_dxe_write_register (wcn,WCN36XX_DXE_ENCH_ADDR , +WCN36XX_DXE_INT_CH1_MASK ); +break ; +case WCN36XX_DXE_CH_RX_H : + dxe->ctrl =WCN36XX_DXE_CTRL_RX_H ; +wcn36xx_dxe_write_register (wcn,WCN36XX_DXE_ENCH_ADDR , +WCN36XX_DXE_INT_CH3_MASK ); +break ; +default : +wcn36xx_warn ("Unknown channel\n" ); + } + +dma_unmap_single (NULL , dma_addr,WCN36XX_PKT_SIZE , +DMA_FROM_DEVICE ); +wcn36xx_rx_skb (wcn, skb); + ctl = ctl->next; + dxe = ctl->desc; + } + + ch->head_blk_ctl = ctl; + +return 0 ; +} + +void wcn36xx_dxe_rx_frame (struct wcn36xx *wcn) +{ +int int_src; + +wcn36xx_dxe_read_register (wcn,WCN36XX_DXE_INT_SRC_RAW_REG , &int_src); + +/* RX_LOW_PRI */ +if (int_src &WCN36XX_DXE_INT_CH1_MASK ) { +wcn36xx_dxe_write_register (wcn,WCN36XX_DXE_0_INT_CLR , +WCN36XX_DXE_INT_CH1_MASK ); +wcn36xx_rx_handle_packets (wcn, &(wcn->dxe_rx_l_ch)); + } + +/* RX_HIGH_PRI */ +if (int_src &WCN36XX_DXE_INT_CH3_MASK ) { +/* Clean up all the INT within this channel */ +wcn36xx_dxe_write_register (wcn,WCN36XX_DXE_0_INT_CLR , +WCN36XX_DXE_INT_CH3_MASK ); +wcn36xx_rx_handle_packets (wcn, &(wcn->dxe_rx_h_ch)); + } + +if (!int_src) +wcn36xx_warn ("No DXE interrupt pending\n" ); +} + +int wcn36xx_dxe_allocate_mem_pools (struct wcn36xx *wcn) +{ +size_t s; +void *cpu_addr; + +/* Allocate BD headers for MGMT frames */ + +/* Where this come from ask QC */ + wcn->mgmt_mem_pool.chunk_size =WCN36XX_BD_CHUNK_SIZE + +16 - (WCN36XX_BD_CHUNK_SIZE %8 ); + + s = wcn->mgmt_mem_pool.chunk_size *WCN36XX_DXE_CH_DESC_NUMB_TX_H ; + cpu_addr =dma_alloc_coherent (NULL , s, &wcn->mgmt_mem_pool.phy_addr, +GFP_KERNEL ); +if (!cpu_addr) + goto out_err; + + wcn->mgmt_mem_pool.virt_addr = cpu_addr; +memset (cpu_addr,0 , s); + +/* Allocate BD headers for DATA frames */ + +/* Where this come from ask QC */ + wcn->data_mem_pool.chunk_size =WCN36XX_BD_CHUNK_SIZE + +16 - (WCN36XX_BD_CHUNK_SIZE %8 ); + + s = wcn->data_mem_pool.chunk_size *WCN36XX_DXE_CH_DESC_NUMB_TX_L ; + cpu_addr =dma_alloc_coherent (NULL , s, &wcn->data_mem_pool.phy_addr, +GFP_KERNEL ); +if (!cpu_addr) + goto out_err; + + wcn->data_mem_pool.virt_addr = cpu_addr; +memset (cpu_addr,0 , s); + +return 0 ; + +out_err: +wcn36xx_dxe_free_mem_pools (wcn); +wcn36xx_err ("Failed to allocate BD mempool\n" ); +return -ENOMEM ; +} + +void wcn36xx_dxe_free_mem_pools (struct wcn36xx *wcn) +{ +if (wcn->mgmt_mem_pool.virt_addr) +dma_free_coherent (NULL , wcn->mgmt_mem_pool.chunk_size * +WCN36XX_DXE_CH_DESC_NUMB_TX_H , + wcn->mgmt_mem_pool.virt_addr, + wcn->mgmt_mem_pool.phy_addr); + +if (wcn->data_mem_pool.virt_addr) { +dma_free_coherent (NULL , wcn->data_mem_pool.chunk_size * +WCN36XX_DXE_CH_DESC_NUMB_TX_L , + wcn->data_mem_pool.virt_addr, + wcn->data_mem_pool.phy_addr); + } +} + +int wcn36xx_dxe_tx_frame (struct wcn36xx *wcn, +struct wcn36xx_vif *vif_priv, +struct sk_buff *skb, +bool is_low) +{ +struct wcn36xx_dxe_ctl *ctl =NULL ; +struct wcn36xx_dxe_desc *desc =NULL ; +struct wcn36xx_dxe_ch *ch =NULL ; +unsigned long flags; + + ch = is_low ? &wcn->dxe_tx_l_ch : &wcn->dxe_tx_h_ch; + + ctl = ch->head_blk_ctl; + +spin_lock_irqsave (&ctl->next->skb_lock, flags); + +/* +* If skb is not null that means that we reached the tail of the ring +* hence ring is full. Stop queues to let mac80211 back off until ring +* has an empty slot again. +*/ +if (NULL != ctl->next->skb) { +ieee80211_stop_queues (wcn->hw); + wcn->queues_stopped = true; +spin_unlock_irqrestore (&ctl->next->skb_lock, flags); +return -EBUSY ; + } +spin_unlock_irqrestore (&ctl->next->skb_lock, flags); + + ctl->skb =NULL ; + desc = ctl->desc; + +/* Set source address of the BD we send */ + desc->src_addr_l = ctl->bd_phy_addr; + + desc->dst_addr_l = ch->dxe_wq; + desc->fr_len =sizeof (struct wcn36xx_tx_bd ); + desc->ctrl = ch->ctrl_bd; + +wcn36xx_dbg (WCN36XX_DBG_DXE ,"DXE TX\n" ); + +wcn36xx_dbg_dump (WCN36XX_DBG_DXE_DUMP ,"DESC1 >>> " , + (char *)desc,sizeof (*desc)); +wcn36xx_dbg_dump (WCN36XX_DBG_DXE_DUMP , +"BD >>> " , (char *)ctl->bd_cpu_addr, +sizeof (struct wcn36xx_tx_bd )); + +/* Set source address of the SKB we send */ + ctl = ctl->next; + ctl->skb = skb; + desc = ctl->desc; +if (ctl->bd_cpu_addr) { +wcn36xx_err ("bd_cpu_addr cannot be NULL for skb DXE\n" ); +return -EINVAL ; + } + + desc->src_addr_l =dma_map_single (NULL , + ctl->skb->data, + ctl->skb->len, +DMA_TO_DEVICE ); + + desc->dst_addr_l = ch->dxe_wq; + desc->fr_len = ctl->skb->len; + +/* set dxe descriptor to VALID */ + desc->ctrl = ch->ctrl_skb; + +wcn36xx_dbg_dump (WCN36XX_DBG_DXE_DUMP ,"DESC2 >>> " , + (char *)desc,sizeof (*desc)); +wcn36xx_dbg_dump (WCN36XX_DBG_DXE_DUMP ,"SKB >>> " , + (char *)ctl->skb->data, ctl->skb->len); + +/* Move the head of the ring to the next empty descriptor */ + ch->head_blk_ctl = ctl->next; + +/* +* When connected and trying to send data frame chip can be in sleep +* mode and writing to the register will not wake up the chip. Instead +* notify chip about new frame through SMSM bus. +*/ +if (is_low && vif_priv->pw_state ==WCN36XX_BMPS ) { + wcn->ctrl_ops->smsm_change_state ( +0 , +WCN36XX_SMSM_WLAN_TX_ENABLE ); + }else { +/* indicate End Of Packet and generate interrupt on descriptor +* done. +*/ +wcn36xx_dxe_write_register (wcn, + ch->reg_ctrl, ch->def_ctrl); + } + +return 0 ; +} + +int wcn36xx_dxe_init (struct wcn36xx *wcn) +{ +int reg_data =0 , ret; + + reg_data =WCN36XX_DXE_REG_RESET ; +wcn36xx_dxe_write_register (wcn,WCN36XX_DXE_REG_CSR_RESET , reg_data); + +/* Setting interrupt path */ + reg_data =WCN36XX_DXE_CCU_INT ; +wcn36xx_dxe_write_register (wcn,WCN36XX_DXE_REG_CCU_INT , reg_data); + +/***************************************/ +/* Init descriptors for TX LOW channel */ +/***************************************/ +wcn36xx_dxe_init_descs (&wcn->dxe_tx_l_ch); +wcn36xx_dxe_init_tx_bd (&wcn->dxe_tx_l_ch, &wcn->data_mem_pool); + +/* Write channel head to a NEXT register */ +wcn36xx_dxe_write_register (wcn,WCN36XX_DXE_CH_NEXT_DESC_ADDR_TX_L , + wcn->dxe_tx_l_ch.head_blk_ctl->desc_phy_addr); + +/* Program DMA destination addr for TX LOW */ +wcn36xx_dxe_write_register (wcn, +WCN36XX_DXE_CH_DEST_ADDR_TX_L , +WCN36XX_DXE_WQ_TX_L ); + +wcn36xx_dxe_read_register (wcn,WCN36XX_DXE_REG_CH_EN , ®_data); +wcn36xx_dxe_enable_ch_int (wcn,WCN36XX_INT_MASK_CHAN_TX_L ); + +/***************************************/ +/* Init descriptors for TX HIGH channel */ +/***************************************/ +wcn36xx_dxe_init_descs (&wcn->dxe_tx_h_ch); +wcn36xx_dxe_init_tx_bd (&wcn->dxe_tx_h_ch, &wcn->mgmt_mem_pool); + +/* Write channel head to a NEXT register */ +wcn36xx_dxe_write_register (wcn,WCN36XX_DXE_CH_NEXT_DESC_ADDR_TX_H , + wcn->dxe_tx_h_ch.head_blk_ctl->desc_phy_addr); + +/* Program DMA destination addr for TX HIGH */ +wcn36xx_dxe_write_register (wcn, +WCN36XX_DXE_CH_DEST_ADDR_TX_H , +WCN36XX_DXE_WQ_TX_H ); + +wcn36xx_dxe_read_register (wcn,WCN36XX_DXE_REG_CH_EN , ®_data); + +/* Enable channel interrupts */ +wcn36xx_dxe_enable_ch_int (wcn,WCN36XX_INT_MASK_CHAN_TX_H ); + +/***************************************/ +/* Init descriptors for RX LOW channel */ +/***************************************/ +wcn36xx_dxe_init_descs (&wcn->dxe_rx_l_ch); + +/* For RX we need to preallocated buffers */ +wcn36xx_dxe_ch_alloc_skb (wcn, &wcn->dxe_rx_l_ch); + +/* Write channel head to a NEXT register */ +wcn36xx_dxe_write_register (wcn,WCN36XX_DXE_CH_NEXT_DESC_ADDR_RX_L , + wcn->dxe_rx_l_ch.head_blk_ctl->desc_phy_addr); + +/* Write DMA source address */ +wcn36xx_dxe_write_register (wcn, +WCN36XX_DXE_CH_SRC_ADDR_RX_L , +WCN36XX_DXE_WQ_RX_L ); + +/* Program preallocated destination address */ +wcn36xx_dxe_write_register (wcn, +WCN36XX_DXE_CH_DEST_ADDR_RX_L , + wcn->dxe_rx_l_ch.head_blk_ctl->desc->phy_next_l); + +/* Enable default control registers */ +wcn36xx_dxe_write_register (wcn, +WCN36XX_DXE_REG_CTL_RX_L , +WCN36XX_DXE_CH_DEFAULT_CTL_RX_L ); + +/* Enable channel interrupts */ +wcn36xx_dxe_enable_ch_int (wcn,WCN36XX_INT_MASK_CHAN_RX_L ); + +/***************************************/ +/* Init descriptors for RX HIGH channel */ +/***************************************/ +wcn36xx_dxe_init_descs (&wcn->dxe_rx_h_ch); + +/* For RX we need to prealocat buffers */ +wcn36xx_dxe_ch_alloc_skb (wcn, &wcn->dxe_rx_h_ch); + +/* Write chanel head to a NEXT register */ +wcn36xx_dxe_write_register (wcn,WCN36XX_DXE_CH_NEXT_DESC_ADDR_RX_H , + wcn->dxe_rx_h_ch.head_blk_ctl->desc_phy_addr); + +/* Write DMA source address */ +wcn36xx_dxe_write_register (wcn, +WCN36XX_DXE_CH_SRC_ADDR_RX_H , +WCN36XX_DXE_WQ_RX_H ); + +/* Program preallocated destination address */ +wcn36xx_dxe_write_register (wcn, +WCN36XX_DXE_CH_DEST_ADDR_RX_H , + wcn->dxe_rx_h_ch.head_blk_ctl->desc->phy_next_l); + +/* Enable default control registers */ +wcn36xx_dxe_write_register (wcn, +WCN36XX_DXE_REG_CTL_RX_H , +WCN36XX_DXE_CH_DEFAULT_CTL_RX_H ); + +/* Enable channel interrupts */ +wcn36xx_dxe_enable_ch_int (wcn,WCN36XX_INT_MASK_CHAN_RX_H ); + + ret =wcn36xx_dxe_request_irqs (wcn); +if (ret <0 ) + goto out_err; + +return 0 ; + +out_err: +return ret; +} + +void wcn36xx_dxe_deinit (struct wcn36xx *wcn) +{ +free_irq (wcn->tx_irq, wcn); +free_irq (wcn->rx_irq, wcn); + +if (wcn->tx_ack_skb) { +ieee80211_tx_status_irqsafe (wcn->hw, wcn->tx_ack_skb); + wcn->tx_ack_skb =NULL ; + } + +wcn36xx_dxe_ch_free_skbs (wcn, &wcn->dxe_rx_l_ch); +wcn36xx_dxe_ch_free_skbs (wcn, &wcn->dxe_rx_h_ch); +}drivers/net/wireless/ath/wcn36xx/dxe.h new file +284
-0@@ -0,0 +1,284 @@ +/* +* Copyright (c) 2013 Eugene Krasnikov <[email protected]> +* +* Permission to use, copy, modify, and/or distribute this software for any +* purpose with or without fee is hereby granted, provided that the above +* copyright notice and this permission notice appear in all copies. +* +* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES +* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF +* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY +* SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES +* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION +* OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN +* CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. +*/ + +#ifndef _DXE_H_ +#define _DXE_H_ + +#include "wcn36xx.h" + +/* +TX_LOW = DMA0 +TX_HIGH = DMA4 +RX_LOW = DMA1 +RX_HIGH = DMA3 +H2H_TEST_RX_TX = DMA2 +*/ + +/* DXE registers */ +#define WCN36XX_DXE_MEM_BASE 0x03000000 +#define WCN36XX_DXE_MEM_REG 0x202000 + +#define WCN36XX_DXE_CCU_INT 0xA0011 +#define WCN36XX_DXE_REG_CCU_INT 0x200b10 + +/* TODO This must calculated properly but not hardcoded */ +#define WCN36XX_DXE_CTRL_TX_L 0x328a44 +#define WCN36XX_DXE_CTRL_TX_H 0x32ce44 +#define WCN36XX_DXE_CTRL_RX_L 0x12ad2f +#define WCN36XX_DXE_CTRL_RX_H 0x12d12f +#define WCN36XX_DXE_CTRL_TX_H_BD 0x30ce45 +#define WCN36XX_DXE_CTRL_TX_H_SKB 0x32ce4d +#define WCN36XX_DXE_CTRL_TX_L_BD 0x308a45 +#define WCN36XX_DXE_CTRL_TX_L_SKB 0x328a4d + +/* TODO This must calculated properly but not hardcoded */ +#define WCN36XX_DXE_WQ_TX_L 0x17 +#define WCN36XX_DXE_WQ_TX_H 0x17 +#define WCN36XX_DXE_WQ_RX_L 0xB +#define WCN36XX_DXE_WQ_RX_H 0x4 + +/* DXE descriptor control filed */ +#define WCN36XX_DXE_CTRL_VALID_MASK (0x00000001) + +/* TODO This must calculated properly but not hardcoded */ +/* DXE default control register values */ +#define WCN36XX_DXE_CH_DEFAULT_CTL_RX_L 0x847EAD2F +#define WCN36XX_DXE_CH_DEFAULT_CTL_RX_H 0x84FED12F +#define WCN36XX_DXE_CH_DEFAULT_CTL_TX_H 0x853ECF4D +#define WCN36XX_DXE_CH_DEFAULT_CTL_TX_L 0x843e8b4d + +/* Common DXE registers */ +#define WCN36XX_DXE_MEM_CSR (WCN36XX_DXE_MEM_REG + 0x00) +#define WCN36XX_DXE_REG_CSR_RESET (WCN36XX_DXE_MEM_REG + 0x00) +#define WCN36XX_DXE_ENCH_ADDR (WCN36XX_DXE_MEM_REG + 0x04) +#define WCN36XX_DXE_REG_CH_EN (WCN36XX_DXE_MEM_REG + 0x08) +#define WCN36XX_DXE_REG_CH_DONE (WCN36XX_DXE_MEM_REG + 0x0C) +#define WCN36XX_DXE_REG_CH_ERR (WCN36XX_DXE_MEM_REG + 0x10) +#define WCN36XX_DXE_INT_MASK_REG (WCN36XX_DXE_MEM_REG + 0x18) +#define WCN36XX_DXE_INT_SRC_RAW_REG (WCN36XX_DXE_MEM_REG + 0x20) +/* #define WCN36XX_DXE_INT_CH6_MASK 0x00000040 */ +/* #define WCN36XX_DXE_INT_CH5_MASK 0x00000020 */ +#define WCN36XX_DXE_INT_CH4_MASK 0x00000010 +#define WCN36XX_DXE_INT_CH3_MASK 0x00000008 +/* #define WCN36XX_DXE_INT_CH2_MASK 0x00000004 */ +#define WCN36XX_DXE_INT_CH1_MASK 0x00000002 +#define WCN36XX_DXE_INT_CH0_MASK 0x00000001 +#define WCN36XX_DXE_0_INT_CLR (WCN36XX_DXE_MEM_REG + 0x30) +#define WCN36XX_DXE_0_INT_ED_CLR (WCN36XX_DXE_MEM_REG + 0x34) +#define WCN36XX_DXE_0_INT_DONE_CLR (WCN36XX_DXE_MEM_REG + 0x38) +#define WCN36XX_DXE_0_INT_ERR_CLR (WCN36XX_DXE_MEM_REG + 0x3C) + +#define WCN36XX_DXE_0_CH0_STATUS (WCN36XX_DXE_MEM_REG + 0x404) +#define WCN36XX_DXE_0_CH1_STATUS (WCN36XX_DXE_MEM_REG + 0x444) +#define WCN36XX_DXE_0_CH2_STATUS (WCN36XX_DXE_MEM_REG + 0x484) +#define WCN36XX_DXE_0_CH3_STATUS (WCN36XX_DXE_MEM_REG + 0x4C4) +#define WCN36XX_DXE_0_CH4_STATUS (WCN36XX_DXE_MEM_REG + 0x504) + +#define WCN36XX_DXE_REG_RESET 0x5c89 + +/* Temporary BMU Workqueue 4 */ +#define WCN36XX_DXE_BMU_WQ_RX_LOW 0xB +#define WCN36XX_DXE_BMU_WQ_RX_HIGH 0x4 +/* DMA channel offset */ +#define WCN36XX_DXE_TX_LOW_OFFSET 0x400 +#define WCN36XX_DXE_TX_HIGH_OFFSET 0x500 +#define WCN36XX_DXE_RX_LOW_OFFSET 0x440 +#define WCN36XX_DXE_RX_HIGH_OFFSET 0x4C0 + +/* Address of the next DXE descriptor */ +#define WCN36XX_DXE_CH_NEXT_DESC_ADDR 0x001C +#define WCN36XX_DXE_CH_NEXT_DESC_ADDR_TX_L (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_TX_LOW_OFFSET + \ + WCN36XX_DXE_CH_NEXT_DESC_ADDR) +#define WCN36XX_DXE_CH_NEXT_DESC_ADDR_TX_H (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_TX_HIGH_OFFSET + \ + WCN36XX_DXE_CH_NEXT_DESC_ADDR) +#define WCN36XX_DXE_CH_NEXT_DESC_ADDR_RX_L (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_RX_LOW_OFFSET + \ + WCN36XX_DXE_CH_NEXT_DESC_ADDR) +#define WCN36XX_DXE_CH_NEXT_DESC_ADDR_RX_H (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_RX_HIGH_OFFSET + \ + WCN36XX_DXE_CH_NEXT_DESC_ADDR) + +/* DXE Descriptor source address */ +#define WCN36XX_DXE_CH_SRC_ADDR 0x000C +#define WCN36XX_DXE_CH_SRC_ADDR_RX_L (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_RX_LOW_OFFSET + \ + WCN36XX_DXE_CH_SRC_ADDR) +#define WCN36XX_DXE_CH_SRC_ADDR_RX_H (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_RX_HIGH_OFFSET + \ + WCN36XX_DXE_CH_SRC_ADDR) + +/* DXE Descriptor address destination address */ +#define WCN36XX_DXE_CH_DEST_ADDR 0x0014 +#define WCN36XX_DXE_CH_DEST_ADDR_TX_L (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_TX_LOW_OFFSET + \ + WCN36XX_DXE_CH_DEST_ADDR) +#define WCN36XX_DXE_CH_DEST_ADDR_TX_H (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_TX_HIGH_OFFSET + \ + WCN36XX_DXE_CH_DEST_ADDR) +#define WCN36XX_DXE_CH_DEST_ADDR_RX_L (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_RX_LOW_OFFSET + \ + WCN36XX_DXE_CH_DEST_ADDR) +#define WCN36XX_DXE_CH_DEST_ADDR_RX_H (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_RX_HIGH_OFFSET + \ + WCN36XX_DXE_CH_DEST_ADDR) + +/* Interrupt status */ +#define WCN36XX_DXE_CH_STATUS_REG_ADDR 0x0004 +#define WCN36XX_DXE_CH_STATUS_REG_ADDR_TX_L (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_TX_LOW_OFFSET + \ + WCN36XX_DXE_CH_STATUS_REG_ADDR) +#define WCN36XX_DXE_CH_STATUS_REG_ADDR_TX_H (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_TX_HIGH_OFFSET + \ + WCN36XX_DXE_CH_STATUS_REG_ADDR) +#define WCN36XX_DXE_CH_STATUS_REG_ADDR_RX_L (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_RX_LOW_OFFSET + \ + WCN36XX_DXE_CH_STATUS_REG_ADDR) +#define WCN36XX_DXE_CH_STATUS_REG_ADDR_RX_H (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_RX_HIGH_OFFSET + \ + WCN36XX_DXE_CH_STATUS_REG_ADDR) + + +/* DXE default control register */ +#define WCN36XX_DXE_REG_CTL_RX_L (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_RX_LOW_OFFSET) +#define WCN36XX_DXE_REG_CTL_RX_H (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_RX_HIGH_OFFSET) +#define WCN36XX_DXE_REG_CTL_TX_H (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_TX_HIGH_OFFSET) +#define WCN36XX_DXE_REG_CTL_TX_L (WCN36XX_DXE_MEM_REG + \ + WCN36XX_DXE_TX_LOW_OFFSET) + +#define WCN36XX_SMSM_WLAN_TX_ENABLE 0x00000400 +#define WCN36XX_SMSM_WLAN_TX_RINGS_EMPTY 0x00000200 + + +/* Interrupt control channel mask */ +#define WCN36XX_INT_MASK_CHAN_TX_L 0x00000001 +#define WCN36XX_INT_MASK_CHAN_RX_L 0x00000002 +#define WCN36XX_INT_MASK_CHAN_RX_H 0x00000008 +#define WCN36XX_INT_MASK_CHAN_TX_H 0x00000010 + +#define WCN36XX_BD_CHUNK_SIZE 128 + +#define WCN36XX_PKT_SIZE 0xF20 +enum wcn36xx_dxe_ch_type { +WCN36XX_DXE_CH_TX_L , +WCN36XX_DXE_CH_TX_H , +WCN36XX_DXE_CH_RX_L , +WCN36XX_DXE_CH_RX_H +}; + +/* amount of descriptors per channel */ +enum wcn36xx_dxe_ch_desc_num { +WCN36XX_DXE_CH_DESC_NUMB_TX_L =128 , +WCN36XX_DXE_CH_DESC_NUMB_TX_H =10 , +WCN36XX_DXE_CH_DESC_NUMB_RX_L =512 , +WCN36XX_DXE_CH_DESC_NUMB_RX_H =40 +}; + +/** +* struct wcn36xx_dxe_desc - describes descriptor of one DXE buffer +* +* @ctrl: is a union that consists of following bits: +* union { +* u32 valid :1; //0 = DMA stop, 1 = DMA continue with this +* //descriptor +* u32 transfer_type :2; //0 = Host to Host space +* u32 eop :1; //End of Packet +* u32 bd_handling :1; //if transferType = Host to BMU, then 0 +* // means first 128 bytes contain BD, and 1 +* // means create new empty BD +* u32 siq :1; // SIQ +* u32 diq :1; // DIQ +* u32 pdu_rel :1; //0 = don't release BD and PDUs when done, +* // 1 = release them +* u32 bthld_sel :4; //BMU Threshold Select +* u32 prio :3; //Specifies the priority level to use for +* // the transfer +* u32 stop_channel :1; //1 = DMA stops processing further, channel +* //requires re-enabling after this +* u32 intr :1; //Interrupt on Descriptor Done +* u32 rsvd :1; //reserved +* u32 size :14;//14 bits used - ignored for BMU transfers, +* //only used for host to host transfers? +* } ctrl; +*/ +struct wcn36xx_dxe_desc { +u32 ctrl; +u32 fr_len; + +u32 src_addr_l; +u32 dst_addr_l; +u32 phy_next_l; +u32 src_addr_h; +u32 dst_addr_h; +u32 phy_next_h; +} __packed; + +/* DXE Control block */ +struct wcn36xx_dxe_ctl { +struct wcn36xx_dxe_ctl *next; +struct wcn36xx_dxe_desc *desc; +unsigned int desc_phy_addr; +int ctl_blk_order; +struct sk_buff *skb; +spinlock_t skb_lock; +void *bd_cpu_addr; +dma_addr_t bd_phy_addr; +}; + +struct wcn36xx_dxe_ch { +enum wcn36xx_dxe_ch_type ch_type; +void *cpu_addr; +dma_addr_t dma_addr; +enum wcn36xx_dxe_ch_desc_num desc_num; +/* DXE control block ring */ +struct wcn36xx_dxe_ctl *head_blk_ctl; +struct wcn36xx_dxe_ctl *tail_blk_ctl; + +/* DXE channel specific configs */ +u32 dxe_wq; +u32 ctrl_bd; +u32 ctrl_skb; +u32 reg_ctrl; +u32 def_ctrl; +}; + +/* Memory Pool for BD headers */ +struct wcn36xx_dxe_mem_pool { +int chunk_size; +void *virt_addr; +dma_addr_t phy_addr; +}; + +struct wcn36xx_vif ; +int wcn36xx_dxe_allocate_mem_pools (struct wcn36xx *wcn); +void wcn36xx_dxe_free_mem_pools (struct wcn36xx *wcn); +void wcn36xx_dxe_rx_frame (struct wcn36xx *wcn); +int wcn36xx_dxe_alloc_ctl_blks (struct wcn36xx *wcn); +void wcn36xx_dxe_free_ctl_blks (struct wcn36xx *wcn); +int wcn36xx_dxe_init (struct wcn36xx *wcn); +void wcn36xx_dxe_deinit (struct wcn36xx *wcn); +int wcn36xx_dxe_init_channels (struct wcn36xx *wcn); +int wcn36xx_dxe_tx_frame (struct wcn36xx *wcn, +struct wcn36xx_vif *vif_priv, +struct sk_buff *skb, +bool is_low); +void wcn36xx_dxe_tx_ack_ind (struct wcn36xx *wcn,u32 status); +void *wcn36xx_dxe_get_next_bd (struct wcn36xx *wcn,bool is_low); +#endif /* _DXE_H_ */ drivers/net/wireless/ath/wcn36xx/hal.h new file +4657
-0@@ -0,0 +1,4657 @@ +/* +* Copyright (c) 2013 Eugene Krasnikov <[email protected]> +* +* Permission to use, copy, modify, and/or distribute this software for any +* purpose with or without fee is hereby granted, provided that the above +* copyright notice and this permission notice appear in all copies. +* +* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES +* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF +* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY +* SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES +* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION +* OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN +* CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. +*/ + +#ifndef _HAL_H_ +#define _HAL_H_ + +/*--------------------------------------------------------------------------- + API VERSIONING INFORMATION + + The RIVA API is versioned as MAJOR.MINOR.VERSION.REVISION + The MAJOR is incremented for major product/architecture changes + (and then MINOR/VERSION/REVISION are zeroed) + The MINOR is incremented for minor product/architecture changes + (and then VERSION/REVISION are zeroed) + The VERSION is incremented if a significant API change occurs + (and then REVISION is zeroed) + The REVISION is incremented if an insignificant API change occurs + or if a new API is added + All values are in the range 0..255 (ie they are 8-bit values) + ---------------------------------------------------------------------------*/ +#define WCN36XX_HAL_VER_MAJOR 1 +#define WCN36XX_HAL_VER_MINOR 4 +#define WCN36XX_HAL_VER_VERSION 1 +#define WCN36XX_HAL_VER_REVISION 2 + +/* This is to force compiler to use the maximum of an int ( 4 bytes ) */ +#define WCN36XX_HAL_MAX_ENUM_SIZE 0x7FFFFFFF +#define WCN36XX_HAL_MSG_TYPE_MAX_ENUM_SIZE 0x7FFF + +/* Max no. of transmit categories */ +#define STACFG_MAX_TC 8 + +/* The maximum value of access category */ +#define WCN36XX_HAL_MAX_AC 4 + +#define WCN36XX_HAL_IPV4_ADDR_LEN 4 + +#define WALN_HAL_STA_INVALID_IDX 0xFF +#define WCN36XX_HAL_BSS_INVALID_IDX 0xFF + +/* Default Beacon template size */ +#define BEACON_TEMPLATE_SIZE 0x180 + +/* Param Change Bitmap sent to HAL */ +#define PARAM_BCN_INTERVAL_CHANGED (1 << 0) +#define PARAM_SHORT_PREAMBLE_CHANGED (1 << 1) +#define PARAM_SHORT_SLOT_TIME_CHANGED (1 << 2) +#define PARAM_llACOEXIST_CHANGED (1 << 3) +#define PARAM_llBCOEXIST_CHANGED (1 << 4) +#define PARAM_llGCOEXIST_CHANGED (1 << 5) +#define PARAM_HT20MHZCOEXIST_CHANGED (1<<6) +#define PARAM_NON_GF_DEVICES_PRESENT_CHANGED (1<<7) +#define PARAM_RIFS_MODE_CHANGED (1<<8) +#define PARAM_LSIG_TXOP_FULL_SUPPORT_CHANGED (1<<9) +#define PARAM_OBSS_MODE_CHANGED (1<<10) +#define PARAM_BEACON_UPDATE_MASK \ + (PARAM_BCN_INTERVAL_CHANGED | \ + PARAM_SHORT_PREAMBLE_CHANGED | \ + PARAM_SHORT_SLOT_TIME_CHANGED | \ + PARAM_llACOEXIST_CHANGED | \ + PARAM_llBCOEXIST_CHANGED | \ + PARAM_llGCOEXIST_CHANGED | \ + PARAM_HT20MHZCOEXIST_CHANGED | \ + PARAM_NON_GF_DEVICES_PRESENT_CHANGED | \ + PARAM_RIFS_MODE_CHANGED | \ + PARAM_LSIG_TXOP_FULL_SUPPORT_CHANGED | \ + PARAM_OBSS_MODE_CHANGED) + +/* dump command response Buffer size */ +#define DUMPCMD_RSP_BUFFER 100 + +/* version string max length (including NULL) */ +#define WCN36XX_HAL_VERSION_LENGTH 64 + +/* message types for messages exchanged between WDI and HAL */ +enum wcn36xx_hal_host_msg_type { + /* Init/De-Init */ + WCN36XX_HAL_START_REQ = 0, + WCN36XX_HAL_START_RSP = 1, + WCN36XX_HAL_STOP_REQ = 2, + WCN36XX_HAL_STOP_RSP = 3, + + /* Scan */ + WCN36XX_HAL_INIT_SCAN_REQ = 4, + WCN36XX_HAL_INIT_SCAN_RSP = 5, + WCN36XX_HAL_START_SCAN_REQ = 6, + WCN36XX_HAL_START_SCAN_RSP = 7, + WCN36XX_HAL_END_SCAN_REQ = 8, + WCN36XX_HAL_END_SCAN_RSP = 9, + WCN36XX_HAL_FINISH_SCAN_REQ = 10, + WCN36XX_HAL_FINISH_SCAN_RSP = 11, + + /* HW STA configuration/deconfiguration */ + WCN36XX_HAL_CONFIG_STA_REQ = 12, + WCN36XX_HAL_CONFIG_STA_RSP = 13, + WCN36XX_HAL_DELETE_STA_REQ = 14, + WCN36XX_HAL_DELETE_STA_RSP = 15, + WCN36XX_HAL_CONFIG_BSS_REQ = 16, + WCN36XX_HAL_CONFIG_BSS_RSP = 17, + WCN36XX_HAL_DELETE_BSS_REQ = 18, + WCN36XX_HAL_DELETE_BSS_RSP = 19, + + /* Infra STA asscoiation */ + WCN36XX_HAL_JOIN_REQ = 20, + WCN36XX_HAL_JOIN_RSP = 21, + WCN36XX_HAL_POST_ASSOC_REQ = 22, + WCN36XX_HAL_POST_ASSOC_RSP = 23, + + /* Security */ + WCN36XX_HAL_SET_BSSKEY_REQ = 24, + WCN36XX_HAL_SET_BSSKEY_RSP = 25, + WCN36XX_HAL_SET_STAKEY_REQ = 26, + WCN36XX_HAL_SET_STAKEY_RSP = 27, + WCN36XX_HAL_RMV_BSSKEY_REQ = 28, + WCN36XX_HAL_RMV_BSSKEY_RSP = 29, + WCN36XX_HAL_RMV_STAKEY_REQ = 30, + WCN36XX_HAL_RMV_STAKEY_RSP = 31, + + /* Qos Related */ + WCN36XX_HAL_ADD_TS_REQ = 32, + WCN36XX_HAL_ADD_TS_RSP = 33, + WCN36XX_HAL_DEL_TS_REQ = 34, + WCN36XX_HAL_DEL_TS_RSP = 35, + WCN36XX_HAL_UPD_EDCA_PARAMS_REQ = 36, + WCN36XX_HAL_UPD_EDCA_PARAMS_RSP = 37, + WCN36XX_HAL_ADD_BA_REQ = 38, + WCN36XX_HAL_ADD_BA_RSP = 39, + WCN36XX_HAL_DEL_BA_REQ = 40, + WCN36XX_HAL_DEL_BA_RSP = 41, + + WCN36XX_HAL_CH_SWITCH_REQ = 42, + WCN36XX_HAL_CH_SWITCH_RSP = 43, + WCN36XX_HAL_SET_LINK_ST_REQ = 44, + WCN36XX_HAL_SET_LINK_ST_RSP = 45, + WCN36XX_HAL_GET_STATS_REQ = 46, + WCN36XX_HAL_GET_STATS_RSP = 47, + WCN36XX_HAL_UPDATE_CFG_REQ = 48, + WCN36XX_HAL_UPDATE_CFG_RSP = 49, + + WCN36XX_HAL_MISSED_BEACON_IND = 50, + WCN36XX_HAL_UNKNOWN_ADDR2_FRAME_RX_IND = 51, + WCN36XX_HAL_MIC_FAILURE_IND = 52, + WCN36XX_HAL_FATAL_ERROR_IND = 53, + WCN36XX_HAL_SET_KEYDONE_MSG = 54, + + /* NV Interface */ + WCN36XX_HAL_DOWNLOAD_NV_REQ = 55, + WCN36XX_HAL_DOWNLOAD_NV_RSP = 56, + + WCN36XX_HAL_ADD_BA_SESSION_REQ = 57, + WCN36XX_HAL_ADD_BA_SESSION_RSP = 58, + WCN36XX_HAL_TRIGGER_BA_REQ = 59, + WCN36XX_HAL_TRIGGER_BA_RSP = 60, + WCN36XX_HAL_UPDATE_BEACON_REQ = 61, + WCN36XX_HAL_UPDATE_BEACON_RSP = 62, + WCN36XX_HAL_SEND_BEACON_REQ = 63, + WCN36XX_HAL_SEND_BEACON_RSP = 64, + + WCN36XX_HAL_SET_BCASTKEY_REQ = 65, + WCN36XX_HAL_SET_BCASTKEY_RSP = 66, + WCN36XX_HAL_DELETE_STA_CONTEXT_IND = 67, + WCN36XX_HAL_UPDATE_PROBE_RSP_TEMPLATE_REQ = 68, + WCN36XX_HAL_UPDATE_PROBE_RSP_TEMPLATE_RSP = 69, + + /* PTT interface support */ + WCN36XX_HAL_PROCESS_PTT_REQ = 70, + WCN36XX_HAL_PROCESS_PTT_RSP = 71, + + /* BTAMP related events */ + WCN36XX_HAL_SIGNAL_BTAMP_EVENT_REQ = 72, + WCN36XX_HAL_SIGNAL_BTAMP_EVENT_RSP = 73, + WCN36XX_HAL_TL_HAL_FLUSH_AC_REQ = 74, + WCN36XX_HAL_TL_HAL_FLUSH_AC_RSP = 75, + + WCN36XX_HAL_ENTER_IMPS_REQ = 76, + WCN36XX_HAL_EXIT_IMPS_REQ = 77, + WCN36XX_HAL_ENTER_BMPS_REQ = 78, + WCN36XX_HAL_EXIT_BMPS_REQ = 79, + WCN36XX_HAL_ENTER_UAPSD_REQ = 80, + WCN36XX_HAL_EXIT_UAPSD_REQ = 81, + WCN36XX_HAL_UPDATE_UAPSD_PARAM_REQ = 82, + WCN36XX_HAL_CONFIGURE_RXP_FILTER_REQ = 83, + WCN36XX_HAL_ADD_BCN_FILTER_REQ = 84, + WCN36XX_HAL_REM_BCN_FILTER_REQ = 85, + WCN36XX_HAL_ADD_WOWL_BCAST_PTRN = 86, + WCN36XX_HAL_DEL_WOWL_BCAST_PTRN = 87, + WCN36XX_HAL_ENTER_WOWL_REQ = 88, + WCN36XX_HAL_EXIT_WOWL_REQ = 89, + WCN36XX_HAL_HOST_OFFLOAD_REQ = 90, + WCN36XX_HAL_SET_RSSI_THRESH_REQ = 91, + WCN36XX_HAL_GET_RSSI_REQ = 92, + WCN36XX_HAL_SET_UAPSD_AC_PARAMS_REQ = 93, + WCN36XX_HAL_CONFIGURE_APPS_CPU_WAKEUP_STATE_REQ = 94, + + WCN36XX_HAL_ENTER_IMPS_RSP = 95, + WCN36XX_HAL_EXIT_IMPS_RSP = 96, + WCN36XX_HAL_ENTER_BMPS_RSP = 97, + WCN36XX_HAL_EXIT_BMPS_RSP = 98, + WCN36XX_HAL_ENTER_UAPSD_RSP = 99, + WCN36XX_HAL_EXIT_UAPSD_RSP = 100, + WCN36XX_HAL_SET_UAPSD_AC_PARAMS_RSP = 101, + WCN36XX_HAL_UPDATE_UAPSD_PARAM_RSP = 102, + WCN36XX_HAL_CONFIGURE_RXP_FILTER_RSP = 103, + WCN36XX_HAL_ADD_BCN_FILTER_RSP = 104, + WCN36XX_HAL_REM_BCN_FILTER_RSP = 105, + WCN36XX_HAL_SET_RSSI_THRESH_RSP = 106, + WCN36XX_HAL_HOST_OFFLOAD_RSP = 107, + WCN36XX_HAL_ADD_WOWL_BCAST_PTRN_RSP = 108, + WCN36XX_HAL_DEL_WOWL_BCAST_PTRN_RSP = 109, + WCN36XX_HAL_ENTER_WOWL_RSP = 110, + WCN36XX_HAL_EXIT_WOWL_RSP = 111, + WCN36XX_HAL_RSSI_NOTIFICATION_IND = 112, + WCN36XX_HAL_GET_RSSI_RSP = 113, + WCN36XX_HAL_CONFIGURE_APPS_CPU_WAKEUP_STATE_RSP = 114, + + /* 11k related events */ + WCN36XX_HAL_SET_MAX_TX_POWER_REQ = 115, + WCN36XX_HAL_SET_MAX_TX_POWER_RSP = 116, + + /* 11R related msgs */ + WCN36XX_HAL_AGGR_ADD_TS_REQ = 117, + WCN36XX_HAL_AGGR_ADD_TS_RSP = 118, + + /* P2P WLAN_FEATURE_P2P */ + WCN36XX_HAL_SET_P2P_GONOA_REQ = 119, + WCN36XX_HAL_SET_P2P_GONOA_RSP = 120, + + /* WLAN Dump commands */ + WCN36XX_HAL_DUMP_COMMAND_REQ = 121, + WCN36XX_HAL_DUMP_COMMAND_RSP = 122, + + /* OEM_DATA FEATURE SUPPORT */ + WCN36XX_HAL_START_OEM_DATA_REQ = 123, + WCN36XX_HAL_START_OEM_DATA_RSP = 124, + + /* ADD SELF STA REQ and RSP */ + WCN36XX_HAL_ADD_STA_SELF_REQ = 125, + WCN36XX_HAL_ADD_STA_SELF_RSP = 126, + + /* DEL SELF STA SUPPORT */ + WCN36XX_HAL_DEL_STA_SELF_REQ = 127, + WCN36XX_HAL_DEL_STA_SELF_RSP = 128, + + /* Coex Indication */ + WCN36XX_HAL_COEX_IND = 129, + + /* Tx Complete Indication */ + WCN36XX_HAL_OTA_TX_COMPL_IND = 130, + + /* Host Suspend/resume messages */ + WCN36XX_HAL_HOST_SUSPEND_IND = 131, + WCN36XX_HAL_HOST_RESUME_REQ = 132, + WCN36XX_HAL_HOST_RESUME_RSP = 133, + + WCN36XX_HAL_SET_TX_POWER_REQ = 134, + WCN36XX_HAL_SET_TX_POWER_RSP = 135, + WCN36XX_HAL_GET_TX_POWER_REQ = 136, + WCN36XX_HAL_GET_TX_POWER_RSP = 137, + + WCN36XX_HAL_P2P_NOA_ATTR_IND = 138, + + WCN36XX_HAL_ENABLE_RADAR_DETECT_REQ = 139, + WCN36XX_HAL_ENABLE_RADAR_DETECT_RSP = 140, + WCN36XX_HAL_GET_TPC_REPORT_REQ = 141, + WCN36XX_HAL_GET_TPC_REPORT_RSP = 142, + WCN36XX_HAL_RADAR_DETECT_IND = 143, + WCN36XX_HAL_RADAR_DETECT_INTR_IND = 144, + WCN36XX_HAL_KEEP_ALIVE_REQ = 145, + WCN36XX_HAL_KEEP_ALIVE_RSP = 146, + + /* PNO messages */ + WCN36XX_HAL_SET_PREF_NETWORK_REQ = 147, + WCN36XX_HAL_SET_PREF_NETWORK_RSP = 148, + WCN36XX_HAL_SET_RSSI_FILTER_REQ = 149, + WCN36XX_HAL_SET_RSSI_FILTER_RSP = 150, + WCN36XX_HAL_UPDATE_SCAN_PARAM_REQ = 151, + WCN36XX_HAL_UPDATE_SCAN_PARAM_RSP = 152, + WCN36XX_HAL_PREF_NETW_FOUND_IND = 153, + + WCN36XX_HAL_SET_TX_PER_TRACKING_REQ = 154, + WCN36XX_HAL_SET_TX_PER_TRACKING_RSP = 155, + WCN36XX_HAL_TX_PER_HIT_IND = 156, + + WCN36XX_HAL_8023_MULTICAST_LIST_REQ = 157, + WCN36XX_HAL_8023_MULTICAST_LIST_RSP = 158, + + WCN36XX_HAL_SET_PACKET_FILTER_REQ = 159, + WCN36XX_HAL_SET_PACKET_FILTER_RSP = 160, + WCN36XX_HAL_PACKET_FILTER_MATCH_COUNT_REQ = 161, + WCN36XX_HAL_PACKET_FILTER_MATCH_COUNT_RSP = 162, + WCN36XX_HAL_CLEAR_PACKET_FILTER_REQ = 163, + WCN36XX_HAL_CLEAR_PACKET_FILTER_RSP = 164, + + /* + * This is temp fix. Should be removed once Host and Riva code is + * in sync. + */ + WCN36XX_HAL_INIT_SCAN_CON_REQ = 165, + + WCN36XX_HAL_SET_POWER_PARAMS_REQ = 166, + WCN36XX_HAL_SET_POWER_PARAMS_RSP = 167, + + WCN36XX_HAL_TSM_STATS_REQ = 168, + WCN36XX_HAL_TSM_STATS_RSP = 169, + + /* wake reason indication (WOW) */ + WCN36XX_HAL_WAKE_REASON_IND = 170, + + /* GTK offload support */ + WCN36XX_HAL_GTK_OFFLOAD_REQ = 171, + WCN36XX_HAL_GTK_OFFLOAD_RSP = 172, + WCN36XX_HAL_GTK_OFFLOAD_GETINFO_REQ = 173, + WCN36XX_HAL_GTK_OFFLOAD_GETINFO_RSP = 174, + + WCN36XX_HAL_FEATURE_CAPS_EXCHANGE_REQ = 175, + WCN36XX_HAL_FEATURE_CAPS_EXCHANGE_RSP = 176, + WCN36XX_HAL_EXCLUDE_UNENCRYPTED_IND = 177, + + WCN36XX_HAL_SET_THERMAL_MITIGATION_REQ = 178, + WCN36XX_HAL_SET_THERMAL_MITIGATION_RSP = 179, + + WCN36XX_HAL_UPDATE_VHT_OP_MODE_REQ = 182, + WCN36XX_HAL_UPDATE_VHT_OP_MODE_RSP = 183, + + WCN36XX_HAL_P2P_NOA_START_IND = 184, + + WCN36XX_HAL_GET_ROAM_RSSI_REQ = 185, + WCN36XX_HAL_GET_ROAM_RSSI_RSP = 186, + + WCN36XX_HAL_CLASS_B_STATS_IND = 187, + WCN36XX_HAL_DEL_BA_IND = 188, + WCN36XX_HAL_DHCP_START_IND = 189, + WCN36XX_HAL_DHCP_STOP_IND = 190, + + WCN36XX_HAL_MSG_MAX = WCN36XX_HAL_MSG_TYPE_MAX_ENUM_SIZE +}; + +/* Enumeration for Version */ +enum wcn36xx_hal_host_msg_version { + WCN36XX_HAL_MSG_VERSION0 = 0, + WCN36XX_HAL_MSG_VERSION1 = 1, + /* define as 2 bytes data */ + WCN36XX_HAL_MSG_WCNSS_CTRL_VERSION = 0x7FFF, + WCN36XX_HAL_MSG_VERSION_MAX_FIELD = WCN36XX_HAL_MSG_WCNSS_CTRL_VERSION +}; + +enum driver_type { + DRIVER_TYPE_PRODUCTION = 0, + DRIVER_TYPE_MFG = 1, + DRIVER_TYPE_DVT = 2, + DRIVER_TYPE_MAX = WCN36XX_HAL_MAX_ENUM_SIZE +}; + +enum wcn36xx_hal_stop_type { + HAL_STOP_TYPE_SYS_RESET, + HAL_STOP_TYPE_SYS_DEEP_SLEEP, + HAL_STOP_TYPE_RF_KILL, + HAL_STOP_TYPE_MAX = WCN36XX_HAL_MAX_ENUM_SIZE +}; + +enum wcn36xx_hal_sys_mode { + HAL_SYS_MODE_NORMAL, + HAL_SYS_MODE_LEARN, + HAL_SYS_MODE_SCAN, + HAL_SYS_MODE_PROMISC, + HAL_SYS_MODE_SUSPEND_LINK, + HAL_SYS_MODE_ROAM_SCAN, + HAL_SYS_MODE_ROAM_SUSPEND_LINK, + HAL_SYS_MODE_MAX = WCN36XX_HAL_MAX_ENUM_SIZE +}; + +enum phy_chan_bond_state { + /* 20MHz IF bandwidth centered on IF carrier */ + PHY_SINGLE_CHANNEL_CENTERED = 0, + + /* 40MHz IF bandwidth with lower 20MHz supporting the primary channel */ + PHY_DOUBLE_CHANNEL_LOW_PRIMARY = 1, + + /* 40MHz IF bandwidth centered on IF carrier */ + PHY_DOUBLE_CHANNEL_CENTERED = 2, + + /* 40MHz IF bandwidth with higher 20MHz supporting the primary ch */ + PHY_DOUBLE_CHANNEL_HIGH_PRIMARY = 3, + + /* 20/40MHZ offset LOW 40/80MHZ offset CENTERED */ + PHY_QUADRUPLE_CHANNEL_20MHZ_LOW_40MHZ_CENTERED = 4, + + /* 20/40MHZ offset CENTERED 40/80MHZ offset CENTERED */ + PHY_QUADRUPLE_CHANNEL_20MHZ_CENTERED_40MHZ_CENTERED = 5, + + /* 20/40MHZ offset HIGH 40/80MHZ offset CENTERED */ + PHY_QUADRUPLE_CHANNEL_20MHZ_HIGH_40MHZ_CENTERED = 6, + + /* 20/40MHZ offset LOW 40/80MHZ offset LOW */ + PHY_QUADRUPLE_CHANNEL_20MHZ_LOW_40MHZ_LOW = 7, + + /* 20/40MHZ offset HIGH 40/80MHZ offset LOW */ + PHY_QUADRUPLE_CHANNEL_20MHZ_HIGH_40MHZ_LOW = 8, + + /* 20/40MHZ offset LOW 40/80MHZ offset HIGH */ + PHY_QUADRUPLE_CHANNEL_20MHZ_LOW_40MHZ_HIGH = 9, + + /* 20/40MHZ offset-HIGH 40/80MHZ offset HIGH */ + PHY_QUADRUPLE_CHANNEL_20MHZ_HIGH_40MHZ_HIGH = 10, + + PHY_CHANNEL_BONDING_STATE_MAX = WCN36XX_HAL_MAX_ENUM_SIZE +}; + +/* Spatial Multiplexing(SM) Power Save mode */ +enum wcn36xx_hal_ht_mimo_state { + /* Static SM Power Save mode */ + WCN36XX_HAL_HT_MIMO_PS_STATIC = 0, + + /* Dynamic SM Power Save mode */ + WCN36XX_HAL_HT_MIMO_PS_DYNAMIC = 1, + + /* reserved */ + WCN36XX_HAL_HT_MIMO_PS_NA = 2, + + /* SM Power Save disabled */ + WCN36XX_HAL_HT_MIMO_PS_NO_LIMIT = 3, + + WCN36XX_HAL_HT_MIMO_PS_MAX = WCN36XX_HAL_MAX_ENUM_SIZE +}; + +/* each station added has a rate mode which specifies the sta attributes */ +enum sta_rate_mode { + STA_TAURUS = 0, + STA_TITAN, + STA_POLARIS, + STA_11b, + STA_11bg, + STA_11a, + STA_11n, + STA_11ac, + STA_INVALID_RATE_MODE = WCN36XX_HAL_MAX_ENUM_SIZE +}; + +/* 1,2,5.5,11 */ +#define WCN36XX_HAL_NUM_DSSS_RATES 4 + +/* 6,9,12,18,24,36,48,54 */ +#define WCN36XX_HAL_NUM_OFDM_RATES 8 + +/* 72,96,108 */ +#define WCN36XX_HAL_NUM_POLARIS_RATES 3 + +#define WCN36XX_HAL_MAC_MAX_SUPPORTED_MCS_SET 16 + +enum wcn36xx_hal_bss_type { + WCN36XX_HAL_INFRASTRUCTURE_MODE, + + /* Added for softAP support */ + WCN36XX_HAL_INFRA_AP_MODE, + + WCN36XX_HAL_IBSS_MODE, + + /* Added for BT-AMP support */ + WCN36XX_HAL_BTAMP_STA_MODE, + + /* Added for BT-AMP support */ + WCN36XX_HAL_BTAMP_AP_MODE, + + WCN36XX_HAL_AUTO_MODE, + + WCN36XX_HAL_DONOT_USE_BSS_TYPE = WCN36XX_HAL_MAX_ENUM_SIZE +}; + +enum wcn36xx_hal_nw_type { + WCN36XX_HAL_11A_NW_TYPE, + WCN36XX_HAL_11B_NW_TYPE, + WCN36XX_HAL_11G_NW_TYPE, + WCN36XX_HAL_11N_NW_TYPE, + WCN36XX_HAL_DONOT_USE_NW_TYPE = WCN36XX_HAL_MAX_ENUM_SIZE +}; + +#define WCN36XX_HAL_MAC_RATESET_EID_MAX 12 + +enum wcn36xx_hal_ht_operating_mode { + /* No Protection */ + WCN36XX_HAL_HT_OP_MODE_PURE, + + /* Overlap Legacy device present, protection is optional */ + WCN36XX_HAL_HT_OP_MODE_OVERLAP_LEGACY, + + /* No legacy device, but 20 MHz HT present */ + WCN36XX_HAL_HT_OP_MODE_NO_LEGACY_20MHZ_HT, + + /* Protection is required */ + WCN36XX_HAL_HT_OP_MODE_MIXED, + + WCN36XX_HAL_HT_OP_MODE_MAX = WCN36XX_HAL_MAX_ENUM_SIZE +}; + +/* Encryption type enum used with peer */ +enum ani_ed_type { + WCN36XX_HAL_ED_NONE, + WCN36XX_HAL_ED_WEP40, + WCN36XX_HAL_ED_WEP104, + WCN36XX_HAL_ED_TKIP, + WCN36XX_HAL_ED_CCMP, + WCN36XX_HAL_ED_WPI, + WCN36XX_HAL_ED_AES_128_CMAC, + WCN36XX_HAL_ED_NOT_IMPLEMENTED = WCN36XX_HAL_MAX_ENUM_SIZE +}; + +#define WLAN_MAX_KEY_RSC_LEN 16 +#define WLAN_WAPI_KEY_RSC_LEN 16 + +/* MAX key length when ULA is used */ +#define WCN36XX_HAL_MAC_MAX_KEY_LENGTH 32 +#define WCN36XX_HAL_MAC_MAX_NUM_OF_DEFAULT_KEYS 4 + +/* + * Enum to specify whether key is used for TX only, RX only or both. + */ +enum ani_key_direction { + WCN36XX_HAL_TX_ONLY, + WCN36XX_HAL_RX_ONLY, + WCN36XX_HAL_TX_RX, + WCN36XX_HAL_TX_DEFAULT, + WCN36XX_HAL_DONOT_USE_KEY_DIRECTION = WCN36XX_HAL_MAX_ENUM_SIZE +}; + +enum ani_wep_type { + WCN36XX_HAL_WEP_STATIC, + WCN36XX_HAL_WEP_DYNAMIC, + WCN36XX_HAL_WEP_MAX = WCN36XX_HAL_MAX_ENUM_SIZE +}; + +enum wcn36xx_hal_link_state { + + WCN36XX_HAL_LINK_IDLE_STATE = 0, + WCN36XX_HAL_LINK_PREASSOC_STATE = 1, + WCN36XX_HAL_LINK_POSTASSOC_STATE = 2, + WCN36XX_HAL_LINK_AP_STATE = 3, + WCN36XX_HAL_LINK_IBSS_STATE = 4, + + /* BT-AMP Case */ + WCN36XX_HAL_LINK_BTAMP_PREASSOC_STATE = 5, + WCN36XX_HAL_LINK_BTAMP_POSTASSOC_STATE = 6, + WCN36XX_HAL_LINK_BTAMP_AP_STATE = 7, + WCN36XX_HAL_LINK_BTAMP_STA_STATE = 8, + + /* Reserved for HAL Internal Use */ + WCN36XX_HAL_LINK_LEARN_STATE = 9, + WCN36XX_HAL_LINK_SCAN_STATE = 10, + WCN36XX_HAL_LINK_FINISH_SCAN_STATE = 11, + WCN36XX_HAL_LINK_INIT_CAL_STATE = 12, + WCN36XX_HAL_LINK_FINISH_CAL_STATE = 13, + WCN36XX_HAL_LINK_LISTEN_STATE = 14, + + WCN36XX_HAL_LINK_MAX = WCN36XX_HAL_MAX_ENUM_SIZE +}; + +enum wcn36xx_hal_stats_mask { + HAL_SUMMARY_STATS_INFO = 0x00000001, + HAL_GLOBAL_CLASS_A_STATS_INFO = 0x00000002, + HAL_GLOBAL_CLASS_B_STATS_INFO = 0x00000004, + HAL_GLOBAL_CLASS_C_STATS_INFO = 0x00000008, + HAL_GLOBAL_CLASS_D_STATS_INFO = 0x00000010, + HAL_PER_STA_STATS_INFO = 0x00000020 +}; + +/* BT-AMP events type */ +enum bt_amp_event_type { + BTAMP_EVENT_CONNECTION_START, + BTAMP_EVENT_CONNECTION_STOP, + BTAMP_EVENT_CONNECTION_TERMINATED, + + /* This and beyond are invalid values */ + BTAMP_EVENT_TYPE_MAX = WCN36XX_HAL_MAX_ENUM_SIZE, +}; + +/* PE Statistics */ +enum pe_stats_mask { + PE_SUMMARY_STATS_INFO = 0x00000001, + PE_GLOBAL_CLASS_A_STATS_INFO = 0x00000002, + PE_GLOBAL_CLASS_B_STATS_INFO = 0x00000004, + PE_GLOBAL_CLASS_C_STATS_INFO = 0x00000008, + PE_GLOBAL_CLASS_D_STATS_INFO = 0x00000010, + PE_PER_STA_STATS_INFO = 0x00000020, + + /* This and beyond are invalid values */ + PE_STATS_TYPE_MAX = WCN36XX_HAL_MAX_ENUM_SIZE +}; + +/* + * Configuration Parameter IDs + */ +#define WCN36XX_HAL_CFG_STA_ID 0 +#define WCN36XX_HAL_CFG_CURRENT_TX_ANTENNA 1 +#define WCN36XX_HAL_CFG_CURRENT_RX_ANTENNA 2 +#define WCN36XX_HAL_CFG_LOW_GAIN_OVERRIDE 3 +#define WCN36XX_HAL_CFG_POWER_STATE_PER_CHAIN 4 +#define WCN36XX_HAL_CFG_CAL_PERIOD 5 +#define WCN36XX_HAL_CFG_CAL_CONTROL 6 +#define WCN36XX_HAL_CFG_PROXIMITY 7 +#define WCN36XX_HAL_CFG_NETWORK_DENSITY 8 +#define WCN36XX_HAL_CFG_MAX_MEDIUM_TIME 9 +#define WCN36XX_HAL_CFG_MAX_MPDUS_IN_AMPDU 10 +#define WCN36XX_HAL_CFG_RTS_THRESHOLD 11 +#define WCN36XX_HAL_CFG_SHORT_RETRY_LIMIT 12 +#define WCN36XX_HAL_CFG_LONG_RETRY_LIMIT 13 +#define WCN36XX_HAL_CFG_FRAGMENTATION_THRESHOLD 14 +#define WCN36XX_HAL_CFG_DYNAMIC_THRESHOLD_ZERO 15 +#define WCN36XX_HAL_CFG_DYNAMIC_THRESHOLD_ONE 16 +#define WCN36XX_HAL_CFG_DYNAMIC_THRESHOLD_TWO 17 +#define WCN36XX_HAL_CFG_FIXED_RATE 18 +#define WCN36XX_HAL_CFG_RETRYRATE_POLICY 19 +#define WCN36XX_HAL_CFG_RETRYRATE_SECONDARY 20 +#define WCN36XX_HAL_CFG_RETRYRATE_TERTIARY 21 +#define WCN36XX_HAL_CFG_FORCE_POLICY_PROTECTION 22 +#define WCN36XX_HAL_CFG_FIXED_RATE_MULTICAST_24GHZ 23 +#define WCN36XX_HAL_CFG_FIXED_RATE_MULTICAST_5GHZ 24 +#define WCN36XX_HAL_CFG_DEFAULT_RATE_INDEX_24GHZ 25 +#define WCN36XX_HAL_CFG_DEFAULT_RATE_INDEX_5GHZ 26 +#define WCN36XX_HAL_CFG_MAX_BA_SESSIONS 27 +#define WCN36XX_HAL_CFG_PS_DATA_INACTIVITY_TIMEOUT 28 +#define WCN36XX_HAL_CFG_PS_ENABLE_BCN_FILTER 29 +#define WCN36XX_HAL_CFG_PS_ENABLE_RSSI_MONITOR 30 +#define WCN36XX_HAL_CFG_NUM_BEACON_PER_RSSI_AVERAGE 31 +#define WCN36XX_HAL_CFG_STATS_PERIOD 32 +#define WCN36XX_HAL_CFG_CFP_MAX_DURATION 33 +#define WCN36XX_HAL_CFG_FRAME_TRANS_ENABLED 34 +#define WCN36XX_HAL_CFG_DTIM_PERIOD 35 +#define WCN36XX_HAL_CFG_EDCA_WMM_ACBK 36 +#define WCN36XX_HAL_CFG_EDCA_WMM_ACBE 37 +#define WCN36XX_HAL_CFG_EDCA_WMM_ACVO 38 +#define WCN36XX_HAL_CFG_EDCA_WMM_ACVI 39 +#define WCN36XX_HAL_CFG_BA_THRESHOLD_HIGH 40 +#define WCN36XX_HAL_CFG_MAX_BA_BUFFERS 41 +#define WCN36XX_HAL_CFG_RPE_POLLING_THRESHOLD 42 +#define WCN36XX_HAL_CFG_RPE_AGING_THRESHOLD_FOR_AC0_REG 43 +#define WCN36XX_HAL_CFG_RPE_AGING_THRESHOLD_FOR_AC1_REG 44 +#define WCN36XX_HAL_CFG_RPE_AGING_THRESHOLD_FOR_AC2_REG 45 +#define WCN36XX_HAL_CFG_RPE_AGING_THRESHOLD_FOR_AC3_REG 46 +#define WCN36XX_HAL_CFG_NO_OF_ONCHIP_REORDER_SESSIONS 47 +#define WCN36XX_HAL_CFG_PS_LISTEN_INTERVAL 48 +#define WCN36XX_HAL_CFG_PS_HEART_BEAT_THRESHOLD 49 +#define WCN36XX_HAL_CFG_PS_NTH_BEACON_FILTER 50 +#define WCN36XX_HAL_CFG_PS_MAX_PS_POLL 51 +#define WCN36XX_HAL_CFG_PS_MIN_RSSI_THRESHOLD 52 +#define WCN36XX_HAL_CFG_PS_RSSI_FILTER_PERIOD 53 +#define WCN36XX_HAL_CFG_PS_BROADCAST_FRAME_FILTER_ENABLE 54 +#define WCN36XX_HAL_CFG_PS_IGNORE_DTIM 55 +#define WCN36XX_HAL_CFG_PS_ENABLE_BCN_EARLY_TERM 56 +#define WCN36XX_HAL_CFG_DYNAMIC_PS_POLL_VALUE 57 +#define WCN36XX_HAL_CFG_PS_NULLDATA_AP_RESP_TIMEOUT 58 +#define WCN36XX_HAL_CFG_TELE_BCN_WAKEUP_EN 59 +#define WCN36XX_HAL_CFG_TELE_BCN_TRANS_LI 60 +#define WCN36XX_HAL_CFG_TELE_BCN_TRANS_LI_IDLE_BCNS 61 +#define WCN36XX_HAL_CFG_TELE_BCN_MAX_LI 62 +#define WCN36XX_HAL_CFG_TELE_BCN_MAX_LI_IDLE_BCNS 63 +#define WCN36XX_HAL_CFG_TX_PWR_CTRL_ENABLE 64 +#define WCN36XX_HAL_CFG_VALID_RADAR_CHANNEL_LIST 65 +#define WCN36XX_HAL_CFG_TX_POWER_24_20 66 +#define WCN36XX_HAL_CFG_TX_POWER_24_40 67 +#define WCN36XX_HAL_CFG_TX_POWER_50_20 68 +#define WCN36XX_HAL_CFG_TX_POWER_50_40 69 +#define WCN36XX_HAL_CFG_MCAST_BCAST_FILTER_SETTING 70 +#define WCN36XX_HAL_CFG_BCN_EARLY_TERM_WAKEUP_INTERVAL 71 +#define WCN36XX_HAL_CFG_MAX_TX_POWER_2_4 72 +#define WCN36XX_HAL_CFG_MAX_TX_POWER_5 73 +#define WCN36XX_HAL_CFG_INFRA_STA_KEEP_ALIVE_PERIOD 74 +#define WCN36XX_HAL_CFG_ENABLE_CLOSE_LOOP 75 +#define WCN36XX_HAL_CFG_BTC_EXECUTION_MODE 76 +#define WCN36XX_HAL_CFG_BTC_DHCP_BT_SLOTS_TO_BLOCK 77 +#define WCN36XX_HAL_CFG_BTC_A2DP_DHCP_BT_SUB_INTERVALS 78 +#define WCN36XX_HAL_CFG_PS_TX_INACTIVITY_TIMEOUT 79 +#define WCN36XX_HAL_CFG_WCNSS_API_VERSION 80 +#define WCN36XX_HAL_CFG_AP_KEEPALIVE_TIMEOUT 81 +#define WCN36XX_HAL_CFG_GO_KEEPALIVE_TIMEOUT 82 +#define WCN36XX_HAL_CFG_ENABLE_MC_ADDR_LIST 83 +#define WCN36XX_HAL_CFG_BTC_STATIC_LEN_INQ_BT 84 +#define WCN36XX_HAL_CFG_BTC_STATIC_LEN_PAGE_BT 85 +#define WCN36XX_HAL_CFG_BTC_STATIC_LEN_CONN_BT 86 +#define WCN36XX_HAL_CFG_BTC_STATIC_LEN_LE_BT 87 +#define WCN36XX_HAL_CFG_BTC_STATIC_LEN_INQ_WLAN 88 +#define WCN36XX_HAL_CFG_BTC_STATIC_LEN_PAGE_WLAN 89 +#define WCN36XX_HAL_CFG_BTC_STATIC_LEN_CONN_WLAN 90 +#define WCN36XX_HAL_CFG_BTC_STATIC_LEN_LE_WLAN 91 +#define WCN36XX_HAL_CFG_BTC_DYN_MAX_LEN_BT 92 +#define WCN36XX_HAL_CFG_BTC_DYN_MAX_LEN_WLAN 93 +#define WCN36XX_HAL_CFG_BTC_MAX_SCO_BLOCK_PERC 94 +#define WCN36XX_HAL_CFG_BTC_DHCP_PROT_ON_A2DP 95 +#define WCN36XX_HAL_CFG_BTC_DHCP_PROT_ON_SCO 96 +#define WCN36XX_HAL_CFG_ENABLE_UNICAST_FILTER 97 +#define WCN36XX_HAL_CFG_MAX_ASSOC_LIMIT 98 +#define WCN36XX_HAL_CFG_ENABLE_LPWR_IMG_TRANSITION 99 +#define WCN36XX_HAL_CFG_ENABLE_MCC_ADAPTIVE_SCHEDULER 100 +#define WCN36XX_HAL_CFG_ENABLE_DETECT_PS_SUPPORT 101 +#define WCN36XX_HAL_CFG_AP_LINK_MONITOR_TIMEOUT 102 +#define WCN36XX_HAL_CFG_BTC_DWELL_TIME_MULTIPLIER 103 +#define WCN36XX_HAL_CFG_ENABLE_TDLS_OXYGEN_MODE 104 +#define WCN36XX_HAL_CFG_MAX_PARAMS 105 + +/* Message definitons - All the messages below need to be packed */ + +/* Definition for HAL API Version. */ +struct wcnss_wlan_version { + u8 revision; + u8 version; + u8 minor; + u8 major; +} __packed; + +/* Definition for Encryption Keys */ +struct wcn36xx_hal_keys { + u8 id; + + /* 0 for multicast */ + u8 unicast; + + enum ani_key_direction direction; + + /* Usage is unknown */ + u8 rsc[WLAN_MAX_KEY_RSC_LEN]; + + /* =1 for authenticator,=0 for supplicant */ + u8 pae_role; + + u16 length; + u8 key[WCN36XX_HAL_MAC_MAX_KEY_LENGTH]; +} __packed; + +/* + * set_sta_key_params Moving here since it is shared by + * configbss/setstakey msgs + */ +struct wcn36xx_hal_set_sta_key_params { + /* STA Index */ + u16 sta_index; + + /* Encryption Type used with peer */ + enum ani_ed_type enc_type; + + /* STATIC/DYNAMIC - valid only for WEP */ + enum ani_wep_type wep_type; + + /* Default WEP key, valid only for static WEP, must between 0 and 3. */ + u8 def_wep_idx; + + /* valid only for non-static WEP encyrptions */ + struct wcn36xx_hal_keys key[WCN36XX_HAL_MAC_MAX_NUM_OF_DEFAULT_KEYS]; + + /* + * Control for Replay Count, 1= Single TID based replay count on Tx + * 0 = Per TID based replay count on TX + */ + u8 single_tid_rc; + +} __packed; + +/* 4-byte control message header used by HAL*/ +struct wcn36xx_hal_msg_header { + enum wcn36xx_hal_host_msg_type msg_type:16; + enum wcn36xx_hal_host_msg_version msg_version:16; + u32 len; +} __packed; + +/* Config format required by HAL for each CFG item*/ +struct wcn36xx_hal_cfg { + /* Cfg Id. The Id required by HAL is exported by HAL + * in shared header file between UMAC and HAL.*/ + u16 id; + + /* Length of the Cfg. This parameter is used to go to next cfg + * in the TLV format.*/ + u16 len; + + /* Padding bytes for unaligned address's */ + u16 pad_bytes; + + /* Reserve bytes for making cfgVal to align address */ + u16 reserve; + + /* Following the uCfgLen field there should be a 'uCfgLen' bytes + * containing the uCfgValue ; u8 uCfgValue[uCfgLen] */ +} __packed; + +struct wcn36xx_hal_mac_start_parameters { + /* Drive Type - Production or FTM etc */ + enum driver_type type; + + /* Length of the config buffer */ + u32 len; + + /* Following this there is a TLV formatted buffer of length + * "len" bytes containing all config values. + * The TLV is expected to be formatted like this: + * 0 15 31 31+CFG_LEN-1 length-1 + * | CFG_ID | CFG_LEN | CFG_BODY | CFG_ID |......| + */ +} __packed; + +struct wcn36xx_hal_mac_start_req_msg { + /* config buffer must start in TLV format just here */ + struct wcn36xx_hal_msg_header header; + struct wcn36xx_hal_mac_start_parameters params; +} __packed; + +struct wcn36xx_hal_mac_start_rsp_params { + /* success or failure */ + u16 status; + + /* Max number of STA supported by the device */ + u8 stations; + + /* Max number of BSS supported by the device */ + u8 bssids; + + /* API Version */ + struct wcnss_wlan_version version; + + /* CRM build information */ + u8 crm_version[WCN36XX_HAL_VERSION_LENGTH]; + + /* hardware/chipset/misc version information */ + u8 wlan_version[WCN36XX_HAL_VERSION_LENGTH]; + +} __packed; + +struct wcn36xx_hal_mac_start_rsp_msg { + struct wcn36xx_hal_msg_header header; + struct wcn36xx_hal_mac_start_rsp_params start_rsp_params; +} __packed; + +struct wcn36xx_hal_mac_stop_req_params { + /* The reason for which the device is being stopped */ + enum wcn36xx_hal_stop_type reason; + +} __packed; + +struct wcn36xx_hal_mac_stop_req_msg { + struct wcn36xx_hal_msg_header header; + struct wcn36xx_hal_mac_stop_req_params stop_req_params; +} __packed; + +struct wcn36xx_hal_mac_stop_rsp_msg { + struct wcn36xx_hal_msg_header header; + + /* success or failure */ + u32 status; +} __packed; + +struct wcn36xx_hal_update_cfg_req_msg { + /* + * Note: The length specified in tHalUpdateCfgReqMsg messages should be + * header.msgLen = sizeof(tHalUpdateCfgReqMsg) + uConfigBufferLen + */ + struct wcn36xx_hal_msg_header header; + + /* Length of the config buffer. Allows UMAC to update multiple CFGs */ + u32 len; + + /* + * Following this there is a TLV formatted buffer of length + * "uConfigBufferLen" bytes containing all config values. + * The TLV is expected to be formatted like this: + * 0 15 31 31+CFG_LEN-1 length-1 + * | CFG_ID | CFG_LEN | CFG_BODY | CFG_ID |......| + */ + +} __packed; + +struct wcn36xx_hal_update_cfg_rsp_msg { + struct wcn36xx_hal_msg_header header; + + /* success or failure */ + u32 status; + +} __packed; + +/* Frame control field format (2 bytes) */ +struct wcn36xx_hal_mac_frame_ctl { + +#ifndef ANI_LITTLE_BIT_ENDIAN + + u8 subType:4; + u8 type:2; + u8 protVer:2; + + u8 order:1; + u8 wep:1; + u8 moreData:1; + u8 powerMgmt:1; + u8 retry:1; + u8 moreFrag:1; + u8 fromDS:1; + u8 toDS:1; + +#else + + u8 protVer:2; + u8 type:2; + u8 subType:4; + + u8 toDS:1; + u8 fromDS:1; + u8 moreFrag:1; + u8 retry:1; + u8 powerMgmt:1; + u8 moreData:1; + u8 wep:1; + u8 order:1; + +#endif + +}; + +/* Sequence control field */ +struct wcn36xx_hal_mac_seq_ctl { + u8 fragNum:4; + u8 seqNumLo:4; + u8 seqNumHi:8; +}; + +/* Management header format */ +struct wcn36xx_hal_mac_mgmt_hdr { + struct wcn36xx_hal_mac_frame_ctl fc; + u8 durationLo; + u8 durationHi; + u8 da[6]; + u8 sa[6]; + u8 bssId[6]; + struct wcn36xx_hal_mac_seq_ctl seqControl; +}; + +/* FIXME: pronto v1 apparently has 4 */ +#define WCN36XX_HAL_NUM_BSSID 2 + +/* Scan Entry to hold active BSS idx's */ +struct wcn36xx_hal_scan_entry { + u8 bss_index[WCN36XX_HAL_NUM_BSSID]; + u8 active_bss_count; +}; + +struct wcn36xx_hal_init_scan_req_msg { + struct wcn36xx_hal_msg_header header; + + /* LEARN - AP Role + SCAN - STA Role */ + enum wcn36xx_hal_sys_mode mode; + + /* BSSID of the BSS */ + u8 bssid[ETH_ALEN]; + + /* Whether BSS needs to be notified */ + u8 notify; + + /* Kind of frame to be used for notifying the BSS (Data Null, QoS + * Null, or CTS to Self). Must always be a valid frame type. */ + u8 frame_type; + + /* UMAC has the option of passing the MAC frame to be used for + * notifying the BSS. If non-zero, HAL will use the MAC frame + * buffer pointed to by macMgmtHdr. If zero, HAL will generate the + * appropriate MAC frame based on frameType. */ + u8 frame_len; + + /* Following the framelength there is a MAC frame buffer if + * frameLength is non-zero. */ + struct wcn36xx_hal_mac_mgmt_hdr mac_mgmt_hdr; + + /* Entry to hold number of active BSS idx's */ + struct wcn36xx_hal_scan_entry scan_entry; +}; + +struct wcn36xx_hal_init_scan_con_req_msg { + struct wcn36xx_hal_msg_header header; + + /* LEARN - AP Role + SCAN - STA Role */ + enum wcn36xx_hal_sys_mode mode; + + /* BSSID of the BSS */ + u8 bssid[ETH_ALEN]; + + /* Whether BSS needs to be notified */ + u8 notify; + + /* Kind of frame to be used for notifying the BSS (Data Null, QoS + * Null, or CTS to Self). Must always be a valid frame type. */ + u8 frame_type; + + /* UMAC has the option of passing the MAC frame to be used for + * notifying the BSS. If non-zero, HAL will use the MAC frame + * buffer pointed to by macMgmtHdr. If zero, HAL will generate the + * appropriate MAC frame based on frameType. */ + u8 frame_length; + + /* Following the framelength there is a MAC frame buffer if + * frameLength is non-zero. */ + struct wcn36xx_hal_mac_mgmt_hdr mac_mgmt_hdr; + + /* Entry to hold number of active BSS idx's */ + struct wcn36xx_hal_scan_entry scan_entry; + + /* Single NoA usage in Scanning */ + u8 use_noa; + + /* Indicates the scan duration (in ms) */ + u16 scan_duration; + +}; + +struct wcn36xx_hal_init_scan_rsp_msg { + struct wcn36xx_hal_msg_header header; + + /* success or failure */ + u32 status; + +} __packed; + +struct wcn36xx_hal_start_scan_req_msg { + struct wcn36xx_hal_msg_header header; + + /* Indicates the channel to scan */ + u8 scan_channel; +} __packed; + +struct wcn36xx_hal_start_rsp_msg { + struct wcn36xx_hal_msg_header header; + + /* success or failure */ + u32 status; + + u32 start_tsf[2]; + u8 tx_mgmt_power; + +} __packed; + +struct wcn36xx_hal_end_scan_req_msg { + struct wcn36xx_hal_msg_header header; + + /* Indicates the channel to stop scanning. Not used really. But + * retained for symmetry with "start Scan" message. It can also + * help in error check if needed. */ + u8 scan_channel; +} __packed; + +struct wcn36xx_hal_end_scan_rsp_msg { + struct wcn36xx_hal_msg_header header; + + /* success or failure */ + u32 status; +} __packed; + +struct wcn36xx_hal_finish_scan_req_msg { + struct wcn36xx_hal_msg_header header; + + /* Identifies the operational state of the AP/STA + * LEARN - AP Role SCAN - STA Role */ + enum wcn36xx_hal_sys_mode mode; + + /* Operating channel to tune to. */ + u8 oper_channel; + + /* Channel Bonding state If 20/40 MHz is operational, this will + * indicate the 40 MHz extension channel in combination with the + * control channel */ + enum phy_chan_bond_state cb_state; + + /* BSSID of the BSS */ + u8 bssid[ETH_ALEN]; + + /* Whether BSS needs to be notified */ + u8 notify; + + /* Kind of frame to be used for notifying the BSS (Data Null, QoS + * Null, or CTS to Self). Must always be a valid frame type. */ + u8 frame_type; + + /* UMAC has the option of passing the MAC frame to be used for + * notifying the BSS. If non-zero, HAL will use the MAC frame + * buffer pointed to by macMgmtHdr. If zero, HAL will generate the + * appropriate MAC frame based on frameType. */ + u8 frame_length; + + /* Following the framelength there is a MAC frame buffer if + * frameLength is non-zero. */ + struct wcn36xx_hal_mac_mgmt_hdr mac_mgmt_hdr; + + /* Entry to hold number of active BSS idx's */ + struct wcn36xx_hal_scan_entry scan_entry; + +} __packed; + +struct wcn36xx_hal_finish_scan_rsp_msg { + struct wcn36xx_hal_msg_header header; + + /* success or failure */ + u32 status; + +} __packed; + +enum wcn36xx_hal_rate_index { + HW_RATE_INDEX_1MBPS = 0x82, + HW_RATE_INDEX_2MBPS = 0x84, + HW_RATE_INDEX_5_5MBPS = 0x8B, + HW_RATE_INDEX_6MBPS = 0x0C, + HW_RATE_INDEX_9MBPS = 0x12, + HW_RATE_INDEX_11MBPS = 0x96, + HW_RATE_INDEX_12MBPS = 0x18, + HW_RATE_INDEX_18MBPS = 0x24, + HW_RATE_INDEX_24MBPS = 0x30, + HW_RATE_INDEX_36MBPS = 0x48, + HW_RATE_INDEX_48MBPS = 0x60, + HW_RATE_INDEX_54MBPS = 0x6C +}; + +struct wcn36xx_hal_supported_rates { + /* + * For Self STA Entry: this represents Self Mode. + * For Peer Stations, this represents the mode of the peer. + * On Station: + * + * --this mode is updated when PE adds the Self Entry. + * + * -- OR when PE sends 'ADD_BSS' message and station context in BSS + * is used to indicate the mode of the AP. + * + * ON AP: + * + * -- this mode is updated when PE sends 'ADD_BSS' and Sta entry + * for that BSS is used to indicate the self mode of the AP. + * + * -- OR when a station is associated, PE sends 'ADD_STA' message + * with this mode updated. + */ + + enum sta_rate_mode op_rate_mode; + + /* 11b, 11a and aniLegacyRates are IE rates which gives rate in + * unit of 500Kbps */ + u16 dsss_rates[WCN36XX_HAL_NUM_DSSS_RATES]; + u16 ofdm_rates[WCN36XX_HAL_NUM_OFDM_RATES]; + u16 legacy_rates[WCN36XX_HAL_NUM_POLARIS_RATES]; + u16 reserved; + + /* Taurus only supports 26 Titan Rates(no ESF/concat Rates will be + * supported) First 26 bits are reserved for those Titan rates and + * the last 4 bits(bit28-31) for Taurus, 2(bit26-27) bits are + * reserved. */ + /* Titan and Taurus Rates */ + u32 enhanced_rate_bitmap; + + /* + * 0-76 bits used, remaining reserved + * bits 0-15 and 32 should be set. + */ + u8 supported_mcs_set[WCN36XX_HAL_MAC_MAX_SUPPORTED_MCS_SET]; + + /* + * RX Highest Supported Data Rate defines the highest data + * rate that the STA is able to receive, in unites of 1Mbps. + * This value is derived from "Supported MCS Set field" inside + * the HT capability element. + */ + u16 rx_highest_data_rate; + +} __packed; + +struct wcn36xx_hal_config_sta_params { + /* BSSID of STA */ + u8 bssid[ETH_ALEN]; + + /* ASSOC ID, as assigned by UMAC */ + u16 aid; + + /* STA entry Type: 0 - Self, 1 - Other/Peer, 2 - BSSID, 3 - BCAST */ + u8 type; + + /* Short Preamble Supported. */ + u8 short_preamble_supported; + + /* MAC Address of STA */ + u8 mac[ETH_ALEN]; + + /* Listen interval of the STA */ + u16 listen_interval; + + /* Support for 11e/WMM */ + u8 wmm_enabled; + + /* 11n HT capable STA */ + u8 ht_capable; + + /* TX Width Set: 0 - 20 MHz only, 1 - 20/40 MHz */ + u8 tx_channel_width_set; + + /* RIFS mode 0 - NA, 1 - Allowed */ + u8 rifs_mode; + + /* L-SIG TXOP Protection mechanism + 0 - No Support, 1 - Supported + SG - there is global field */ + u8 lsig_txop_protection; + + /* Max Ampdu Size supported by STA. TPE programming. + 0 : 8k , 1 : 16k, 2 : 32k, 3 : 64k */ + u8 max_ampdu_size; + + /* Max Ampdu density. Used by RA. 3 : 0~7 : 2^(11nAMPDUdensity -4) */ + u8 max_ampdu_density; + + /* Max AMSDU size 1 : 3839 bytes, 0 : 7935 bytes */ + u8 max_amsdu_size; + + /* Short GI support for 40Mhz packets */ + u8 sgi_40mhz; + + /* Short GI support for 20Mhz packets */ + u8 sgi_20Mhz; + + /* TODO move this parameter to the end for 3680 */ + /* These rates are the intersection of peer and self capabilities. */ + struct wcn36xx_hal_supported_rates supported_rates; + + /* Robust Management Frame (RMF) enabled/disabled */ + u8 rmf; + + /* The unicast encryption type in the association */ + u32 encrypt_type; + + /* HAL should update the existing STA entry, if this flag is set. UMAC + will set this flag in case of RE-ASSOC, where we want to reuse the + old STA ID. 0 = Add, 1 = Update */ + u8 action; + + /* U-APSD Flags: 1b per AC. Encoded as follows: + b7 b6 b5 b4 b3 b2 b1 b0 = + X X X X BE BK VI VO */ + u8 uapsd; + + /* Max SP Length */ + u8 max_sp_len; + + /* 11n Green Field preamble support + 0 - Not supported, 1 - Supported */ + u8 green_field_capable; + + /* MIMO Power Save mode */ + enum wcn36xx_hal_ht_mimo_state mimo_ps; + + /* Delayed BA Support */ + u8 delayed_ba_support; + + /* Max AMPDU duration in 32us */ + u8 max_ampdu_duration; + + /* HT STA should set it to 1 if it is enabled in BSS. HT STA should + * set it to 0 if AP does not support it. This indication is sent + * to HAL and HAL uses this flag to pickup up appropriate 40Mhz + * rates. */ + u8 dsss_cck_mode_40mhz; + + /* Valid STA Idx when action=Update. Set to 0xFF when invalid! + * Retained for backward compalibity with existing HAL code */ + u8 sta_index; + + /* BSSID of BSS to which station is associated. Set to 0xFF when + * invalid. Retained for backward compalibity with existing HAL + * code */ + u8 bssid_index; + + u8 p2p; + + /* TODO add this parameter for 3680. */ + /* Reserved to align next field on a dword boundary */ + /* u8 reserved; */ +} __packed; + +struct wcn36xx_hal_config_sta_req_msg { + struct wcn36xx_hal_msg_header header; + struct wcn36xx_hal_config_sta_params sta_params; +} __packed; + +struct wcn36xx_hal_config_sta_params_v1 { + /* BSSID of STA */ + u8 bssid[ETH_ALEN]; + + /* ASSOC ID, as assigned by UMAC */ + u16 aid; + + /* STA entry Type: 0 - Self, 1 - Other/Peer, 2 - BSSID, 3 - BCAST */ + u8 type; + + /* Short Preamble Supported. */ + u8 short_preamble_supported; + + /* MAC Address of STA */ + u8 mac[ETH_ALEN]; + + /* Listen interval of the STA */ + u16 listen_interval; + + /* Support for 11e/WMM */ + u8 wmm_enabled; + + /* 11n HT capable STA */ + u8 ht_capable; + + /* TX Width Set: 0 - 20 MHz only, 1 - 20/40 MHz */ + u8 tx_channel_width_set; + + /* RIFS mode 0 - NA, 1 - Allowed */ + u8 rifs_mode; + + /* L-SIG TXOP Protection mechanism + 0 - No Support, 1 - Supported + SG - there is global field */ + u8 lsig_txop_protection; + + /* Max Ampdu Size supported by STA. TPE programming. + 0 : 8k , 1 : 16k, 2 : 32k, 3 : 64k */ + u8 max_ampdu_size; + + /* Max Ampdu density. Used by RA. 3 : 0~7 : 2^(11nAMPDUdensity -4) */ + u8 max_ampdu_density; + + /* Max AMSDU size 1 : 3839 bytes, 0 : 7935 bytes */ + u8 max_amsdu_size; + + /* Short GI support for 40Mhz packets */ + u8 sgi_40mhz; + + /* Short GI support for 20Mhz packets */ + u8 sgi_20Mhz; + + /* Robust Management Frame (RMF) enabled/disabled */ + u8 rmf; + + /* The unicast encryption type in the association */ + u32 encrypt_type; + + /* HAL should update the existing STA entry, if this flag is set. UMAC + will set this flag in case of RE-ASSOC, where we want to reuse the + old STA ID. 0 = Add, 1 = Update */ + u8 action; + + /* U-APSD Flags: 1b per AC. Encoded as follows: + b7 b6 b5 b4 b3 b2 b1 b0 = + X X X X BE BK VI VO */ + u8 uapsd; + + /* Max SP Length */ + u8 max_sp_len; + + /* 11n Green Field preamble support + 0 - Not supported, 1 - Supported */ + u8 green_field_capable; + + /* MIMO Power Save mode */ + enum wcn36xx_hal_ht_mimo_state mimo_ps; + + /* Delayed BA Support */ + u8 delayed_ba_support; + + /* Max AMPDU duration in 32us */ + u8 max_ampdu_duration; + + /* HT STA should set it to 1 if it is enabled in BSS. HT STA should + * set it to 0 if AP does not support it. This indication is sent + * to HAL and HAL uses this flag to pickup up appropriate 40Mhz + * rates. */ + u8 dsss_cck_mode_40mhz; + + /* Valid STA Idx when action=Update. Set to 0xFF when invalid! + * Retained for backward compalibity with existing HAL code */ + u8 sta_index; + + /* BSSID of BSS to which station is associated. Set to 0xFF when + * invalid. Retained for backward compalibity with existing HAL + * code */ + u8 bssid_index; + + u8 p2p; + + /* Reserved to align next field on a dword boundary */ + u8 reserved; + + /* These rates are the intersection of peer and self capabilities. */ + struct wcn36xx_hal_supported_rates supported_rates; +} __packed; + +struct wcn36xx_hal_config_sta_req_msg_v1 { + struct wcn36xx_hal_msg_header header; + struct wcn36xx_hal_config_sta_params_v1 sta_params; +} __packed; + +struct config_sta_rsp_params { + /* success or failure */ + u32 status; + + /* Station index; valid only when 'status' field value SUCCESS */ + u8 sta_index; + + /* BSSID Index of BSS to which the station is associated */ + u8 bssid_index; + + /* DPU Index for PTK */ + u8 dpu_index; + + /* DPU Index for GTK */ + u8 bcast_dpu_index; + + /* DPU Index for IGTK */ + u8 bcast_mgmt_dpu_idx; + + /* PTK DPU signature */ + u8 uc_ucast_sig; + + /* GTK DPU isignature */ + u8 uc_bcast_sig; + + /* IGTK DPU signature */ + u8 uc_mgmt_sig; + + u8 p2p; + +} __packed; + +struct wcn36xx_hal_config_sta_rsp_msg { + struct wcn36xx_hal_msg_header header; + + struct config_sta_rsp_params params; +} __packed; + +/* Delete STA Request message */ +struct wcn36xx_hal_delete_sta_req_msg { + struct wcn36xx_hal_msg_header header; + + /* Index of STA to delete */ + u8 sta_index; + +} __packed; + +/* Delete STA Response message */ +struct wcn36xx_hal_delete_sta_rsp_msg { + struct wcn36xx_hal_msg_header header; + + /* success or failure */ + u32 status; + + /* Index of STA deleted */ + u8 sta_id; +} __packed; + +/* 12 Bytes long because this structure can be used to represent rate and + * extended rate set IEs. The parser assume this to be at least 12 */ +struct wcn36xx_hal_rate_set { + u8 num_rates; + u8 rate[WCN36XX_HAL_MAC_RATESET_EID_MAX]; +} __packed; + +/* access category record */ +struct wcn36xx_hal_aci_aifsn { +#ifndef ANI_LITTLE_BIT_ENDIAN + u8 rsvd:1; + u8 aci:2; + u8 acm:1; + u8 aifsn:4; +#else + u8 aifsn:4; + u8 acm:1; + u8 aci:2; + u8 rsvd:1; +#endif +} __packed; + +/* contention window size */ +struct wcn36xx_hal_mac_cw { +#ifndef ANI_LITTLE_BIT_ENDIAN + u8 max:4; + u8 min:4; +#else + u8 min:4; + u8 max:4; +#endif +} __packed; + +struct wcn36xx_hal_edca_param_record { + struct wcn36xx_hal_aci_aifsn aci; + struct wcn36xx_hal_mac_cw cw; + u16 txop_limit; +} __packed; + +struct wcn36xx_hal_mac_ssid { + u8 length; + u8 ssid[32]; +} __packed; + +/* Concurrency role. These are generic IDs that identify the various roles + * in the software system. */ +enum wcn36xx_hal_con_mode { + WCN36XX_HAL_STA_MODE = 0, + + /* to support softAp mode . This is misleading. + It means AP MODE only. */ + WCN36XX_HAL_STA_SAP_MODE = 1, + + WCN36XX_HAL_P2P_CLIENT_MODE, + WCN36XX_HAL_P2P_GO_MODE, + WCN36XX_HAL_MONITOR_MODE, +}; + +/* This is a bit pattern to be set for each mode + * bit 0 - sta mode + * bit 1 - ap mode + * bit 2 - p2p client mode + * bit 3 - p2p go mode */ +enum wcn36xx_hal_concurrency_mode { + HAL_STA = 1, + HAL_SAP = 2, + + /* to support sta, softAp mode . This means STA+AP mode */ + HAL_STA_SAP = 3, + + HAL_P2P_CLIENT = 4, + HAL_P2P_GO = 8, + HAL_MAX_CONCURRENCY_PERSONA = 4 +}; + +struct wcn36xx_hal_config_bss_params { + /* BSSID */ + u8 bssid[ETH_ALEN]; + + /* Self Mac Address */ + u8 self_mac_addr[ETH_ALEN]; + + /* BSS type */ + enum wcn36xx_hal_bss_type bss_type; + + /* Operational Mode: AP =0, STA = 1 */ + u8 oper_mode; + + /* Network Type */ + enum wcn36xx_hal_nw_type nw_type; + + /* Used to classify PURE_11G/11G_MIXED to program MTU */ + u8 short_slot_time_supported; + + /* Co-exist with 11a STA */ + u8 lla_coexist; + + /* Co-exist with 11b STA */ + u8 llb_coexist; + + /* Co-exist with 11g STA */ + u8 llg_coexist; + + /* Coexistence with 11n STA */ + u8 ht20_coexist; + + /* Non GF coexist flag */ + u8 lln_non_gf_coexist; + + /* TXOP protection support */ + u8 lsig_tx_op_protection_full_support; + + /* RIFS mode */ + u8 rifs_mode; + + /* Beacon Interval in TU */ + u16 beacon_interval; + + /* DTIM period */ + u8 dtim_period; + + /* TX Width Set: 0 - 20 MHz only, 1 - 20/40 MHz */ + u8 tx_channel_width_set; + + /* Operating channel */ + u8 oper_channel; + + /* Extension channel for channel bonding */ + u8 ext_channel; + + /* Reserved to align next field on a dword boundary */ + u8 reserved; + + /* TODO move sta to the end for 3680 */ + /* Context of the station being added in HW + * Add a STA entry for "itself" - + * + * On AP - Add the AP itself in an "STA context" + * + * On STA - Add the AP to which this STA is joining in an + * "STA context" + */ + struct wcn36xx_hal_config_sta_params sta; + /* SSID of the BSS */ + struct wcn36xx_hal_mac_ssid ssid; + + /* HAL should update the existing BSS entry, if this flag is set. + * UMAC will set this flag in case of reassoc, where we want to + * resue the the old BSSID and still return success 0 = Add, 1 = + * Update */ + u8 action; + + /* MAC Rate Set */ + struct wcn36xx_hal_rate_set rateset; + + /* Enable/Disable HT capabilities of the BSS */ + u8 ht; + + /* Enable/Disable OBSS protection */ + u8 obss_prot_enabled; +Lines of this file are not shown. View the raw message.
drivers/net/wireless/ath/wcn36xx/main.c new file +1036
-0Lines of this file are not shown. View the raw message.
drivers/net/wireless/ath/wcn36xx/pmc.c new file +62
-0Lines of this file are not shown. View the raw message.
drivers/net/wireless/ath/wcn36xx/pmc.h new file +33
-0Lines of this file are not shown. View the raw message.
drivers/net/wireless/ath/wcn36xx/smd.c new file +2126
-0Lines of this file are not shown. View the raw message.
drivers/net/wireless/ath/wcn36xx/smd.h new file +127
-0Lines of this file are not shown. View the raw message.
drivers/net/wireless/ath/wcn36xx/txrx.c new file +284
-0Lines of this file are not shown. View the raw message.
drivers/net/wireless/ath/wcn36xx/txrx.h new file +160
-0Lines of this file are not shown. View the raw message.
drivers/net/wireless/ath/wcn36xx/wcn36xx.h new file +238
-1Lines of this file are not shown. View the raw message.
The rest of this diff is not shown. View the raw message.
1.8.1.2
Signature · 2 lines
Best regards, Eugene
Part of the diff is not shown here. View the raw message.
Quoted 2 lines · Eugene Krasnikov
This is a mac80211 driver for Qualcomm WCN3660/WCN3680 devices. So far WCN3660/WCN3680 is available only on MSM platform.
some trivia:
drivers/net/wireless/ath/wcn36xx/debug.c
Quoted 1 line
drivers/net/wireless/ath/wcn36xx/debug.c +0
-0
[]
Quoted 9 lines
drivers/net/wireless/ath/wcn36xx/debug.c +9
-0+static ssize_t read_file_bool_bmps (struct file *file,char __user *user_buf, +size_t count,loff_t *ppos) +{ +struct wcn36xx *wcn = file->private_data; +struct wcn36xx_vif *vif_priv =NULL ; +struct ieee80211_vif *vif =NULL ; +char buf[3 ]; + +list_for_each_entry (vif_priv, &wcn->vif_list, list) {
drivers/net/wireless/ath/wcn36xx/debug.c line 52
Quoted 10 lines
drivers/net/wireless/ath/wcn36xx/debug.c +10
-0+ vif =container_of ((void *)vif_priv, + struct ieee80211_vif, + drv_priv); +if (NL80211_IFTYPE_STATION == vif->type) { +if (vif_priv->pw_state ==WCN36XX_BMPS ) + buf[0 ] ='1' ; +else + buf[0 ] ='0' ; +break ; + }
please indent this properly.
list_for_each...(...) {
statement...;
statement...;
}[]
Quoted 14 lines
drivers/net/wireless/ath/wcn36xx/debug.c +14
-0+static ssize_t write_file_bool_bmps (struct file *file, +const char __user *user_buf, +size_t count,loff_t *ppos) +{ +struct wcn36xx *wcn = file->private_data; +struct wcn36xx_vif *vif_priv =NULL ; +struct ieee80211_vif *vif =NULL ; + +char buf[32 ]; +int buf_size; + + buf_size =min (count, (sizeof (buf)-1 )); +if (copy_from_user (buf, user_buf, buf_size)) +return -EFAULT ;
drivers/net/wireless/ath/wcn36xx/debug.c line 83
Quoted 10 lines
drivers/net/wireless/ath/wcn36xx/debug.c +10
-0+ +switch (buf[0 ]) { +case 'y' : +case 'Y' : +case '1' : +list_for_each_entry (vif_priv, &wcn->vif_list, list) { + vif =container_of ((void *)vif_priv, + struct ieee80211_vif, + drv_priv); +if (NL80211_IFTYPE_STATION == vif->type) {
trivia:
Please use
if (test == CONSTANT)
Yes, I know the compiler complains if you
mistakenly leave out one of the = this way.
drivers/net/wireless/ath/wcn36xx/debug.c line 160
Quoted 9 lines
drivers/net/wireless/ath/wcn36xx/debug.c +9
-0+#define ADD_FILE (name, mode, fop, priv_data) \ + do { \ + struct dentry *d; \ + d = debugfs_create_file(__stringify(name), \ + mode, dfs->rootdir, \ + priv_data, fop); \ + dfs->file_##name.dentry = d; \ + if (IS_ERR(d)) { \ + wcn36xx_warn("Create the debugfs entry failed");\
missing "\n" newline
drivers/net/wireless/ath/wcn36xx/debug.c line 161
Quoted 1 line
drivers/net/wireless/ath/wcn36xx/debug.c +1
-0+ dfs->file_##name.dentry = NULL; \
[]
drivers/net/wireless/ath/wcn36xx/dxe.c
Quoted 1 line
drivers/net/wireless/ath/wcn36xx/dxe.c +0
-0
[]
drivers/net/wireless/ath/wcn36xx/dxe.c line 173
Quoted 11 lines
drivers/net/wireless/ath/wcn36xx/dxe.c +11
-0+static int wcn36xx_dxe_init_descs (struct wcn36xx_dxe_ch *wcn_ch) +{ +struct wcn36xx_dxe_desc *cur_dxe =NULL ; +struct wcn36xx_dxe_desc *prev_dxe =NULL ; +struct wcn36xx_dxe_ctl *cur_ctl =NULL ; +size_t size; +int i; + + size = wcn_ch->desc_num *sizeof (struct wcn36xx_dxe_desc ); + wcn_ch->cpu_addr =dma_alloc_coherent (NULL , size, &wcn_ch->dma_addr, +GFP_KERNEL );
dma_zalloc_coherent
[]
drivers/net/wireless/ath/wcn36xx/dxe.c line 177
Quoted 1 line
drivers/net/wireless/ath/wcn36xx/dxe.c +1
-0+memset (wcn_ch->cpu_addr,0 , size);
No longer required.
drivers/net/wireless/ath/wcn36xx/dxe.c line 205
Quoted 1 line
drivers/net/wireless/ath/wcn36xx/dxe.c +1
-0+if (0 == i) {
too many styles mixing i == 0 and 0 == i
[]
drivers/net/wireless/ath/wcn36xx/dxe.c line 522
Quoted 3 lines
drivers/net/wireless/ath/wcn36xx/dxe.c +3
-0+int wcn36xx_dxe_allocate_mem_pools (struct wcn36xx *wcn) +{ +size_t s;
mixing s and size above, please use one style/name.
drivers/net/wireless/ath/wcn36xx/dxe.c line 533
Quoted 11 lines
drivers/net/wireless/ath/wcn36xx/dxe.c +11
-0+void *cpu_addr; + +/* Allocate BD headers for MGMT frames */ + +/* Where this come from ask QC */ + wcn->mgmt_mem_pool.chunk_size =WCN36XX_BD_CHUNK_SIZE + +16 - (WCN36XX_BD_CHUNK_SIZE %8 ); + + s = wcn->mgmt_mem_pool.chunk_size *WCN36XX_DXE_CH_DESC_NUMB_TX_H ; + cpu_addr =dma_alloc_coherent (NULL , s, &wcn->mgmt_mem_pool.phy_addr, +GFP_KERNEL );
same use of dma_zalloc_coherent(...)
drivers/net/wireless/ath/wcn36xx/dxe.c line 538
Quoted 5 lines
drivers/net/wireless/ath/wcn36xx/dxe.c +5
-0+if (!cpu_addr) + goto out_err; + + wcn->mgmt_mem_pool.virt_addr = cpu_addr; +memset (cpu_addr,0 , s);
Now unnecessary memset.
too long, stopped reading.
Hi Joe,
Thanx for you comments. Would you mind if we fix those trivias after wcn36xx is merged?
Quoted 145 lines · Joe Perches
Quoted 2 lines · Eugene Krasnikov
This is a mac80211 driver for Qualcomm WCN3660/WCN3680 devices. So far WCN3660/WCN3680 is available only on MSM platform.
some trivia:
drivers/net/wireless/ath/wcn36xx/debug.c
Quoted 1 line
drivers/net/wireless/ath/wcn36xx/debug.c +0
-0[]
Quoted 9 lines
drivers/net/wireless/ath/wcn36xx/debug.c +9
-0+static ssize_t read_file_bool_bmps (struct file *file,char __user *user_buf, +size_t count,loff_t *ppos) +{ +struct wcn36xx *wcn = file->private_data; +struct wcn36xx_vif *vif_priv =NULL ; +struct ieee80211_vif *vif =NULL ; +char buf[3 ]; + +list_for_each_entry (vif_priv, &wcn->vif_list, list) {drivers/net/wireless/ath/wcn36xx/debug.c line 52
Quoted 10 lines
drivers/net/wireless/ath/wcn36xx/debug.c +10
-0+ vif =container_of ((void *)vif_priv, + struct ieee80211_vif, + drv_priv); +if (NL80211_IFTYPE_STATION == vif->type) { +if (vif_priv->pw_state ==WCN36XX_BMPS ) + buf[0 ] ='1' ; +else + buf[0 ] ='0' ; +break ; + }please indent this properly.
list_for_each...(...) { statement...; statement...; }[]
Quoted 14 lines
drivers/net/wireless/ath/wcn36xx/debug.c +14
-0+static ssize_t write_file_bool_bmps (struct file *file, +const char __user *user_buf, +size_t count,loff_t *ppos) +{ +struct wcn36xx *wcn = file->private_data; +struct wcn36xx_vif *vif_priv =NULL ; +struct ieee80211_vif *vif =NULL ; + +char buf[32 ]; +int buf_size; + + buf_size =min (count, (sizeof (buf)-1 )); +if (copy_from_user (buf, user_buf, buf_size)) +return -EFAULT ;drivers/net/wireless/ath/wcn36xx/debug.c line 83
Quoted 10 lines
drivers/net/wireless/ath/wcn36xx/debug.c +10
-0+ +switch (buf[0 ]) { +case 'y' : +case 'Y' : +case '1' : +list_for_each_entry (vif_priv, &wcn->vif_list, list) { + vif =container_of ((void *)vif_priv, + struct ieee80211_vif, + drv_priv); +if (NL80211_IFTYPE_STATION == vif->type) {trivia:
Please use
if (test == CONSTANT)Yes, I know the compiler complains if you
mistakenly leave out one of the = this way.drivers/net/wireless/ath/wcn36xx/debug.c line 160
Quoted 9 lines
drivers/net/wireless/ath/wcn36xx/debug.c +9
-0+#define ADD_FILE (name, mode, fop, priv_data) \ + do { \ + struct dentry *d; \ + d = debugfs_create_file(__stringify(name), \ + mode, dfs->rootdir, \ + priv_data, fop); \ + dfs->file_##name.dentry = d; \ + if (IS_ERR(d)) { \ + wcn36xx_warn("Create the debugfs entry failed");\missing "\n" newline
Quoted 1 line
+ dfs->file_##name.dentry = NULL; \
[]
drivers/net/wireless/ath/wcn36xx/dxe.c
Quoted 1 line
drivers/net/wireless/ath/wcn36xx/dxe.c +0
-0[]
drivers/net/wireless/ath/wcn36xx/dxe.c line 173
Quoted 11 lines
drivers/net/wireless/ath/wcn36xx/dxe.c +11
-0+static int wcn36xx_dxe_init_descs (struct wcn36xx_dxe_ch *wcn_ch) +{ +struct wcn36xx_dxe_desc *cur_dxe =NULL ; +struct wcn36xx_dxe_desc *prev_dxe =NULL ; +struct wcn36xx_dxe_ctl *cur_ctl =NULL ; +size_t size; +int i; + + size = wcn_ch->desc_num *sizeof (struct wcn36xx_dxe_desc ); + wcn_ch->cpu_addr =dma_alloc_coherent (NULL , size, &wcn_ch->dma_addr, +GFP_KERNEL );
dma_zalloc_coherent[]
Quoted 1 line
+
memset(wcn_ch->cpu_addr, 0, size);No longer required.
Quoted 1 line
+ if (0 == i) {
too many styles mixing i == 0 and 0 == i
[]
drivers/net/wireless/ath/wcn36xx/dxe.c line 522
Quoted 3 lines
drivers/net/wireless/ath/wcn36xx/dxe.c +3
-0+int wcn36xx_dxe_allocate_mem_pools (struct wcn36xx *wcn) +{ +size_t s;mixing s and size above, please use one style/name.
drivers/net/wireless/ath/wcn36xx/dxe.c line 533
Quoted 11 lines
drivers/net/wireless/ath/wcn36xx/dxe.c +11
-0+void *cpu_addr; + +/* Allocate BD headers for MGMT frames */ + +/* Where this come from ask QC */ + wcn->mgmt_mem_pool.chunk_size =WCN36XX_BD_CHUNK_SIZE + +16 - (WCN36XX_BD_CHUNK_SIZE %8 ); + + s = wcn->mgmt_mem_pool.chunk_size *WCN36XX_DXE_CH_DESC_NUMB_TX_H ; + cpu_addr =dma_alloc_coherent (NULL , s, &wcn->mgmt_mem_pool.phy_addr, +GFP_KERNEL );same use of
dma_zalloc_coherent(...)drivers/net/wireless/ath/wcn36xx/dxe.c line 538
Quoted 5 lines
drivers/net/wireless/ath/wcn36xx/dxe.c +5
-0+if (!cpu_addr) + goto out_err; + + wcn->mgmt_mem_pool.virt_addr = cpu_addr; +memset (cpu_addr,0 , s);Now unnecessary memset.
too long, stopped reading.
Signature · 2 lines
Best regards, Eugene
Quoted 1 line · Eugene Krasnikov
Hi Joe,
Hi Eugene.
Quoted 2 lines
Thanx for you comments. Would you mind if we fix those trivias after wcn36xx is merged?
Not at all.
Hi John,
Please pull wcn36xx and let me know if there are any problems.
Quoted 10 lines · Joe Perches
Quoted 1 line · Eugene Krasnikov
Hi Joe,
Hi Eugene.
Quoted 2 lines
Thanx for you comments. Would you mind if we fix those trivias after wcn36xx is merged?
Not at all.
Signature · 2 lines
Best regards, Eugene
Quoted 1 line · Luis R. Rodriguez
Nice! I test compiled with sparse enabled and got this:
Could also consider running smatch.
johannes
Thanx Johannes for advice. Will try it as well.
2013/10/7 Johannes Berg <[email protected]>:
Quoted 8 lines · Luis R. Rodriguez
Quoted 2 lines
Nice! I test compiled with sparse enabled and got this:
Could also consider running smatch.
johannes
Signature · 2 lines
Best regards, Eugene