Skip to contentSkip to conversation

ARM: at91: cpuidle: convert to platform driver

PATCH Superseded Daniel Lezcano 4 participants 12 messages Oct 12, 2013 – Oct 14, 2013

Subsystems (4)

v1 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 ARM: at91: cpuidle: convert to platform driver

Use the platform driver model to separate the cpuidle specific code from the low level pm code. It allows to remove the dependency between these two components.

Tested-on usb-a9263 (at91sam9263)

---
 arch/arm/mach-at91/cpuidle.c |   29 +++++++++++++++--------------
 arch/arm/mach-at91/pm.c      |   16 +++++++++++++++-
 2 files changed, 30 insertions(+), 15 deletions(-)
arch/arm/mach-at91/cpuidle.c +15 -14
index 4ec6a6d..6cdc76d 100644
@@ -21,26 +21,17 @@
 #include <linux/export.h>
 #include <asm/proc-fns.h>
 #include <asm/cpuidle.h>
-#include <mach/cpu.h>
-
-#include "pm.h"
 
 #define AT91_MAX_STATES	2
 
+static void (*at91_standby)(void);
+
 /* Actual code that puts the SoC in different idle states */
 static int at91_enter_idle(struct cpuidle_device *dev,
 			struct cpuidle_driver *drv,
 			       int index)
 {
-	if (cpu_is_at91rm9200())
-		at91rm9200_standby();
-	else if (cpu_is_at91sam9g45())
-		at91sam9g45_standby();
-	else if (cpu_is_at91sam9263())
-		at91sam9263_standby();
-	else
-		at91sam9_standby();
-
+	at91_standby();
 	return index;
 }
 
@@ -60,9 +51,19 @@ static struct cpuidle_driver at91_idle_driver = {
 };
 
 /* Initialize CPU idle by registering the idle states */
-static int __init at91_init_cpuidle(void)
+static int __init at91_cpuidle_probe(struct platform_device *dev)
 {
+	at91_standby = (void *)(dev->dev.platform_data);
+	
 	return cpuidle_register(&at91_idle_driver, NULL);
 }
 
-device_initcall(at91_init_cpuidle);
+static struct platform_driver at91_cpuidle_driver = {
+	.driver = {
+		.name = "cpuidle-at91",
+		.owner = THIS_MODULE,
+	},
+	.probe = at91_cpuidle_probe,
+};
+
+module_platform_driver(at91_cpuidle_driver);
arch/arm/mach-at91/pm.c +15 -1
index 15afb5d..debdbf8 100644
@@ -314,6 +314,10 @@ static const struct platform_suspend_ops at91_pm_ops = {
 	.end	= at91_pm_end,
 };
 
+static struct platform_device at91_cpuidle_device = {
+	.name = "cpuidle-at91",
+};
+
 static int __init at91_pm_init(void)
 {
 #ifdef CONFIG_AT91_SLOW_CLOCK
@@ -323,8 +327,18 @@ static int __init at91_pm_init(void)
 	pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow clock mode)" : ""));
 
 	/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */
-	if (cpu_is_at91rm9200())
+	if (cpu_is_at91rm9200()) {
+		at91_cpuidle_device.dev.platform_data = at91rm9200_standby;
 		at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
+	} else if (cpu_is_at91sam9g45()) {
+		at91_cpuidle_device.dev.platform_data = at91sam9g45_standby;
+	} else if (cpu_is_at91sam9263()) {
+		at91_cpuidle_device.dev.platform_data = at91sam9263_standby;
+	} else {
+		at91_cpuidle_device.dev.platform_data = at91sam9_standby;
+	}
+	
+	platform_device_register(&at91_cpuidle_device);
 
 	suspend_set_ops(&at91_pm_ops);
 
Signature · 1 line
1.7.9.5
#1 lore raw

PATCH 2/2 ARM: at91: cpuidle: Move driver to drivers/cpuidle

As the cpuidle driver code has no more the dependency with the pm code, the 'standby' callback being passed as a parameter to the device's platform data, we can move the cpuidle driver in the drivers/cpuidle directory.

Tested-on usb-a9263 (at91sam9263)

---
 arch/arm/mach-at91/Makefile                        |    1 -
 drivers/cpuidle/Kconfig.arm                        |    6 ++++++
 drivers/cpuidle/Makefile                           |    1 +
 .../cpuidle.c => drivers/cpuidle/cpuidle-at91.c    |    0
 4 files changed, 7 insertions(+), 1 deletion(-)
 rename arch/arm/mach-at91/cpuidle.c => drivers/cpuidle/cpuidle-at91.c (100%)
arch/arm/mach-at91/Makefile +0 -1
index 3b0a953..c1b7370 100644
@@ -98,7 +98,6 @@ obj-y				+= leds.o
 # Power Management
 obj-$(CONFIG_PM)		+= pm.o
 obj-$(CONFIG_AT91_SLOW_CLOCK)	+= pm_slowclock.o
-obj-$(CONFIG_CPU_IDLE)	+= cpuidle.o
 
 ifeq ($(CONFIG_PM_DEBUG),y)
 CFLAGS_pm.o += -DDEBUG
drivers/cpuidle/Kconfig.arm +6 -0
index 8e36603..edecfc8 100644
@@ -27,6 +27,12 @@ config ARM_U8500_CPUIDLE
 	help
 	  Select this to enable cpuidle for ST-E u8500 processors
 
+config ARM_AT91_CPUIDLE
+        bool "Cpu Idle Driver for the AT91 processors"
+	depends on ARCH_AT91
+	help
+	  Select this to enable cpuidle for AT91 processors
+
 config CPU_IDLE_BIG_LITTLE
 	bool "Support for ARM big.LITTLE processors"
 	depends on ARCH_VEXPRESS_TC2_PM
drivers/cpuidle/Makefile +1 -0
index cea5ef5..60c4ae5 100644
@@ -11,4 +11,5 @@ obj-$(CONFIG_ARM_HIGHBANK_CPUIDLE)	+= cpuidle-calxeda.o
 obj-$(CONFIG_ARM_KIRKWOOD_CPUIDLE)	+= cpuidle-kirkwood.o
 obj-$(CONFIG_ARM_ZYNQ_CPUIDLE)		+= cpuidle-zynq.o
 obj-$(CONFIG_ARM_U8500_CPUIDLE)         += cpuidle-ux500.o
+obj-$(CONFIG_ARM_AT91_CPUIDLE)          += cpuidle-at91.o
 obj-$(CONFIG_CPU_IDLE_BIG_LITTLE)	+= cpuidle-big_little.o
drivers/cpuidle/cpuidle-at91.c renamed from arch/arm/mach-at91/cpuidle.c +0 -0
similarity index 100%
rename from arch/arm/mach-at91/cpuidle.c
rename to drivers/cpuidle/cpuidle-at91.c
Signature · 1 line
1.7.9.5
#2 lore raw

PATCH 2/2 ARM: at91: cpuidle: Move driver to drivers/cpuidle

Dear Daniel Lezcano,

drivers/cpuidle/Kconfig.arm config ARM_U8500_CPUIDLE · line 31

Quoted 2 lines · Daniel Lezcano
drivers/cpuidle/Kconfig.arm +2 -0
+config ARM_AT91_CPUIDLE
+        bool "Cpu Idle Driver for the AT91 processors"

Nitpick: indentation is done with spaces here, while it should be one tab.

Thomas

Signature · 3 lines
Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
#3 lore raw

PATCH 2/2 ARM: at91: cpuidle: Move driver to drivers/cpuidle

Quoted 9 lines · Thomas Petazzoni

Dear Daniel Lezcano,

drivers/cpuidle/Kconfig.arm config ARM_U8500_CPUIDLE · line 31

Quoted 2 lines · Daniel Lezcano
drivers/cpuidle/Kconfig.arm +2 -0
+config ARM_AT91_CPUIDLE
+        bool "Cpu Idle Driver for the AT91 processors"

Nitpick: indentation is done with spaces here, while it should be one tab.

Ah, right. Fixed for the V2.

Thanks !
-- Daniel

Signature · 5 lines
  <http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#4 lore raw

PATCH 2/2 ARM: at91: cpuidle: Move driver to drivers/cpuidle

Hi Daniel,

Quoted 5 lines · Daniel Lezcano
Quoted 4 lines · Thomas Petazzoni

Dear Daniel Lezcano,

On Sat, 12 Oct 2013 17:51:39 +0200, Daniel Lezcano wrote:

Quoted 7 lines
Quoted 5 lines

drivers/cpuidle/Kconfig.arm config ARM_U8500_CPUIDLE · line 31

Quoted 2 lines
drivers/cpuidle/Kconfig.arm +2 -0
+config ARM_AT91_CPUIDLE
+        bool "Cpu Idle Driver for the AT91 processors"

Nitpick: indentation is done with spaces here, while it should be one tab.

Ah, right. Fixed for the V2.

Could you also please add 'default y' to preserve the old behavior? (the at91 cpuidle support was always built-in for CONFIG_CPU_IDLE=y)

Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics

#5 lore raw

PATCH 2/2 ARM: at91: cpuidle: Move driver to drivers/cpuidle

Quoted 12 lines · Bartlomiej Zolnierkiewicz

Hi Daniel,

Quoted 8 lines · Daniel Lezcano
Quoted 7 lines · Thomas Petazzoni

Dear Daniel Lezcano,

Quoted 2 lines · Daniel Lezcano
drivers/cpuidle/Kconfig.arm +2 -0
+config ARM_AT91_CPUIDLE
+        bool "Cpu Idle Driver for the AT91 processors"
Quoted 7 lines
Quoted 4 lines
Quoted 2 lines

Nitpick: indentation is done with spaces here, while it should be one tab.

Ah, right. Fixed for the V2.

Could you also please add 'default y' to preserve the old behavior? (the at91 cpuidle support was always built-in for CONFIG_CPU_IDLE=y)

Yes, sure.

Thanks for the review.

-- Daniel

Signature · 5 lines
  <http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#6 lore raw

PATCH 1/2 ARM: at91: cpuidle: convert to platform driver

In reply to Daniel Lezcano
Quoted 87 lines · Daniel Lezcano

Use the platform driver model to separate the cpuidle specific code from the low level pm code. It allows to remove the dependency between these two components.

Tested-on usb-a9263 (at91sam9263)

---
 arch/arm/mach-at91/cpuidle.c |   29 +++++++++++++++--------------
 arch/arm/mach-at91/pm.c      |   16 +++++++++++++++-
 2 files changed, 30 insertions(+), 15 deletions(-)
arch/arm/mach-at91/cpuidle.c +15 -14
index 4ec6a6d..6cdc76d 100644
@@ -21,26 +21,17 @@
 #include <linux/export.h>
 #include <asm/proc-fns.h>
 #include <asm/cpuidle.h>
-#include <mach/cpu.h>
-
-#include "pm.h"
 
 #define AT91_MAX_STATES	2
 
+static void (*at91_standby)(void);
+
 /* Actual code that puts the SoC in different idle states */
 static int at91_enter_idle(struct cpuidle_device *dev,
 			struct cpuidle_driver *drv,
 			       int index)
 {
-	if (cpu_is_at91rm9200())
-		at91rm9200_standby();
-	else if (cpu_is_at91sam9g45())
-		at91sam9g45_standby();
-	else if (cpu_is_at91sam9263())
-		at91sam9263_standby();
-	else
-		at91sam9_standby();
-
+	at91_standby();
 	return index;
 }
 
@@ -60,9 +51,19 @@ static struct cpuidle_driver at91_idle_driver = {
 };
 
 /* Initialize CPU idle by registering the idle states */
-static int __init at91_init_cpuidle(void)
+static int __init at91_cpuidle_probe(struct platform_device *dev)
 {
+	at91_standby = (void *)(dev->dev.platform_data);
+	
 	return cpuidle_register(&at91_idle_driver, NULL);
 }
 
-device_initcall(at91_init_cpuidle);
+static struct platform_driver at91_cpuidle_driver = {
+	.driver = {
+		.name = "cpuidle-at91",
+		.owner = THIS_MODULE,
+	},
+	.probe = at91_cpuidle_probe,
+};
+
+module_platform_driver(at91_cpuidle_driver);
arch/arm/mach-at91/pm.c +4 -0
index 15afb5d..debdbf8 100644
@@ -314,6 +314,10 @@ static const struct platform_suspend_ops at91_pm_ops = {
 	.end	= at91_pm_end,
 };
 
+static struct platform_device at91_cpuidle_device = {
+	.name = "cpuidle-at91",
+};
+
 static int __init at91_pm_init(void)
 {
 #ifdef CONFIG_AT91_SLOW_CLOCK
@@ -323,8 +327,18 @@ static int __init at91_pm_init(void)
 	pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow clock mode)" : ""));
 
 	/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */

arch/arm/mach-at91/pm.c static int __init at91_pm_init(void) · line 338

Quoted 10 lines
arch/arm/mach-at91/pm.c +8 -1
-	if (cpu_is_at91rm9200())
+	if (cpu_is_at91rm9200()) {
+		at91_cpuidle_device.dev.platform_data = at91rm9200_standby;
 		at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
+	} else if (cpu_is_at91sam9g45()) {
+		at91_cpuidle_device.dev.platform_data = at91sam9g45_standby;
+	} else if (cpu_is_at91sam9263()) {
+		at91_cpuidle_device.dev.platform_data = at91sam9263_standby;
+	} else {
+		at91_cpuidle_device.dev.platform_data = at91sam9_standby;

no this is too dangerous when adding new SoC

you must list the supported SoC

and I prefer to move this code to the SoC init structure

so we can drop the if/else if/elsee

and drop the issue of adding new and the arch_initcall

Best Regards,
J.

Quoted 9 lines
arch/arm/mach-at91/pm.c +3 -0
+	}
+	
+	platform_device_register(&at91_cpuidle_device);
 
 	suspend_set_ops(&at91_pm_ops);
 
Signature · 1 line
1.7.9.5
#7 lore raw

PATCH 1/2 ARM: at91: cpuidle: convert to platform driver

Quoted 100 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 87 lines · Daniel Lezcano

Use the platform driver model to separate the cpuidle specific code from the low level pm code. It allows to remove the dependency between these two components.

Tested-on usb-a9263 (at91sam9263)

---
  arch/arm/mach-at91/cpuidle.c |   29 +++++++++++++++--------------
  arch/arm/mach-at91/pm.c      |   16 +++++++++++++++-
  2 files changed, 30 insertions(+), 15 deletions(-)
arch/arm/mach-at91/cpuidle.c +15 -14
index 4ec6a6d..6cdc76d 100644
@@ -21,26 +21,17 @@
  #include <linux/export.h>
  #include <asm/proc-fns.h>
  #include <asm/cpuidle.h>
-#include <mach/cpu.h>
-
-#include "pm.h"
 
  #define AT91_MAX_STATES	2
 
+static void (*at91_standby)(void);
+
  /* Actual code that puts the SoC in different idle states */
  static int at91_enter_idle(struct cpuidle_device *dev,
  			struct cpuidle_driver *drv,
  			       int index)
  {
-	if (cpu_is_at91rm9200())
-		at91rm9200_standby();
-	else if (cpu_is_at91sam9g45())
-		at91sam9g45_standby();
-	else if (cpu_is_at91sam9263())
-		at91sam9263_standby();
-	else
-		at91sam9_standby();
-
+	at91_standby();
  	return index;
  }
 
@@ -60,9 +51,19 @@ static struct cpuidle_driver at91_idle_driver = {
  };
 
  /* Initialize CPU idle by registering the idle states */
-static int __init at91_init_cpuidle(void)
+static int __init at91_cpuidle_probe(struct platform_device *dev)
  {
+	at91_standby = (void *)(dev->dev.platform_data);
+	
  	return cpuidle_register(&at91_idle_driver, NULL);
  }
 
-device_initcall(at91_init_cpuidle);
+static struct platform_driver at91_cpuidle_driver = {
+	.driver = {
+		.name = "cpuidle-at91",
+		.owner = THIS_MODULE,
+	},
+	.probe = at91_cpuidle_probe,
+};
+
+module_platform_driver(at91_cpuidle_driver);
arch/arm/mach-at91/pm.c +4 -0
index 15afb5d..debdbf8 100644
@@ -314,6 +314,10 @@ static const struct platform_suspend_ops at91_pm_ops = {
  	.end	= at91_pm_end,
  };
 
+static struct platform_device at91_cpuidle_device = {
+	.name = "cpuidle-at91",
+};
+
  static int __init at91_pm_init(void)
  {
  #ifdef CONFIG_AT91_SLOW_CLOCK
@@ -323,8 +327,18 @@ static int __init at91_pm_init(void)
  	pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow clock mode)" : ""));
 
  	/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */

arch/arm/mach-at91/pm.c static int __init at91_pm_init(void) · line 338

Quoted 10 lines
arch/arm/mach-at91/pm.c +8 -1
-	if (cpu_is_at91rm9200())
+	if (cpu_is_at91rm9200()) {
+		at91_cpuidle_device.dev.platform_data = at91rm9200_standby;
  		at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
+	} else if (cpu_is_at91sam9g45()) {
+		at91_cpuidle_device.dev.platform_data = at91sam9g45_standby;
+	} else if (cpu_is_at91sam9263()) {
+		at91_cpuidle_device.dev.platform_data = at91sam9263_standby;
+	} else {
+		at91_cpuidle_device.dev.platform_data = at91sam9_standby;

no this is too dangerous when adding new SoC

Quoted 3 lines

you must list the supported SoC

and I prefer to move this code to the SoC init structure

Do you mean register the platform_device in eg. at91rm9200_initialize with the right platform data ?

Quoted 15 lines

so we can drop the if/else if/elsee

and drop the issue of adding new and the arch_initcall

Best Regards,
J.

Quoted 9 lines
arch/arm/mach-at91/pm.c +3 -1
+	}
+	
+	platform_device_register(&at91_cpuidle_device);
 
  	suspend_set_ops(&at91_pm_ops);
 
--

1.7.9.5

Signature · 5 lines
  <http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#8 lore raw

PATCH 1/2 ARM: at91: cpuidle: convert to platform driver

Quoted 101 lines · Daniel Lezcano
Quoted 100 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 87 lines · Daniel Lezcano

Use the platform driver model to separate the cpuidle specific code from the low level pm code. It allows to remove the dependency between these two components.

Tested-on usb-a9263 (at91sam9263)

---
 arch/arm/mach-at91/cpuidle.c |   29 +++++++++++++++--------------
 arch/arm/mach-at91/pm.c      |   16 +++++++++++++++-
 2 files changed, 30 insertions(+), 15 deletions(-)
arch/arm/mach-at91/cpuidle.c +15 -14
index 4ec6a6d..6cdc76d 100644
@@ -21,26 +21,17 @@
 #include <linux/export.h>
 #include <asm/proc-fns.h>
 #include <asm/cpuidle.h>
-#include <mach/cpu.h>
-
-#include "pm.h"
 
 #define AT91_MAX_STATES	2
 
+static void (*at91_standby)(void);
+
 /* Actual code that puts the SoC in different idle states */
 static int at91_enter_idle(struct cpuidle_device *dev,
 			struct cpuidle_driver *drv,
 			       int index)
 {
-	if (cpu_is_at91rm9200())
-		at91rm9200_standby();
-	else if (cpu_is_at91sam9g45())
-		at91sam9g45_standby();
-	else if (cpu_is_at91sam9263())
-		at91sam9263_standby();
-	else
-		at91sam9_standby();
-
+	at91_standby();
 	return index;
 }
 
@@ -60,9 +51,19 @@ static struct cpuidle_driver at91_idle_driver = {
 };
 
 /* Initialize CPU idle by registering the idle states */
-static int __init at91_init_cpuidle(void)
+static int __init at91_cpuidle_probe(struct platform_device *dev)
 {
+	at91_standby = (void *)(dev->dev.platform_data);
+	
 	return cpuidle_register(&at91_idle_driver, NULL);
 }
 
-device_initcall(at91_init_cpuidle);
+static struct platform_driver at91_cpuidle_driver = {
+	.driver = {
+		.name = "cpuidle-at91",
+		.owner = THIS_MODULE,
+	},
+	.probe = at91_cpuidle_probe,
+};
+
+module_platform_driver(at91_cpuidle_driver);
arch/arm/mach-at91/pm.c +4 -0
index 15afb5d..debdbf8 100644
@@ -314,6 +314,10 @@ static const struct platform_suspend_ops at91_pm_ops = {
 	.end	= at91_pm_end,
 };
 
+static struct platform_device at91_cpuidle_device = {
+	.name = "cpuidle-at91",
+};
+
 static int __init at91_pm_init(void)
 {
 #ifdef CONFIG_AT91_SLOW_CLOCK
@@ -323,8 +327,18 @@ static int __init at91_pm_init(void)
 	pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow clock mode)" : ""));
 
 	/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */

arch/arm/mach-at91/pm.c static int __init at91_pm_init(void) · line 338

Quoted 10 lines
arch/arm/mach-at91/pm.c +8 -1
-	if (cpu_is_at91rm9200())
+	if (cpu_is_at91rm9200()) {
+		at91_cpuidle_device.dev.platform_data = at91rm9200_standby;
 		at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
+	} else if (cpu_is_at91sam9g45()) {
+		at91_cpuidle_device.dev.platform_data = at91sam9g45_standby;
+	} else if (cpu_is_at91sam9263()) {
+		at91_cpuidle_device.dev.platform_data = at91sam9263_standby;
+	} else {
+		at91_cpuidle_device.dev.platform_data = at91sam9_standby;

no this is too dangerous when adding new SoC

Quoted 7 lines
Quoted 3 lines

you must list the supported SoC

and I prefer to move this code to the SoC init structure

Do you mean register the platform_device in eg. at91rm9200_initialize with the right platform data ?

yes as example

Best Regards,
J.

Quoted 25 lines
Quoted 16 lines

so we can drop the if/else if/elsee

and drop the issue of adding new and the arch_initcall

Best Regards,
J.

Quoted 9 lines
arch/arm/mach-at91/pm.c +3 -1
+	}
+	
+	platform_device_register(&at91_cpuidle_device);
 
 	suspend_set_ops(&at91_pm_ops);
 
--

1.7.9.5

Signature · 5 lines
 <http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#9 lore raw

PATCH 1/2 ARM: at91: cpuidle: convert to platform driver

Quoted 10 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 9 lines · Daniel Lezcano
Quoted 8 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 7 lines · Daniel Lezcano

Use the platform driver model to separate the cpuidle specific code from the low level pm code. It allows to remove the dependency between these two components.

Tested-on usb-a9263 (at91sam9263)

[ ... ]

Quoted 16 lines
Quoted 16 lines
Quoted 16 lines

Review

Quoted 12 lines

---
/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */

(quoted diff) +8 -1
-	if (cpu_is_at91rm9200())
+	if (cpu_is_at91rm9200()) {
+		at91_cpuidle_device.dev.platform_data = at91rm9200_standby;
  		at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
+	} else if (cpu_is_at91sam9g45()) {
+		at91_cpuidle_device.dev.platform_data = at91sam9g45_standby;
+	} else if (cpu_is_at91sam9263()) {
+		at91_cpuidle_device.dev.platform_data = at91sam9263_standby;
+	} else {
+		at91_cpuidle_device.dev.platform_data = at91sam9_standby;

no this is too dangerous when adding new SoC

you must list the supported SoC

Quoted 8 lines
Quoted 5 lines
Quoted 1 line

and I prefer to move this code to the SoC init structure

Do you mean register the platform_device in eg. at91rm9200_initialize with the right platform data ?

yes as example

Best Regards,

Hi Jean-Christophe,

I did the changes but there are different drawbacks with the approach. The first one is the AT91_SOC_START is too early to call the platform_device_register. The second one is we have multiple declaration of the platform_device which is not really nice.

I found the following solution:

The platform_device is static in pm.c, there is a at91_pm_set_standby function. All AT91_SOC_START call at91_pm_set_standby with the right standby function callback, which in turns set the platform data for the cpuidle platform device. When the init call for pm is made, it registers the platform device.

That has the benefit to encapsulate the platform device and having it in a single place and also we have the information to remove the { if then else } statements we have in 'at91_pm_enter's case block for PM_SUSPEND_STANDBY.

Does it sound ok for you ?

Thanks
-- Daniel

(quoted diff) +0 -0

b/arch/arm/mach-at91/at91rm9200.c
index 4aad93d..0d234f2 100644

arch/arm/mach-at91/at91rm9200.c +3 -0
@@ -27,6 +27,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -337,6 +338,8 @@ static void __init at91rm9200_initialize(void)
  	/* Initialize GPIO subsystem */
  	at91_gpio_init(at91rm9200_gpio,
  		cpu_is_at91rm9200_bga() ? AT91RM9200_BGA : AT91RM9200_PQFP);
+
+	at91_pm_set_standby(at91rm9200_standby);
  }
 
 
(quoted diff) +0 -0

b/arch/arm/mach-at91/at91sam9260.c
index 5de6074..9fd7aa6 100644

arch/arm/mach-at91/at91sam9260.c +1 -0
@@ -28,6 +28,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -307,7 +308,6 @@ static struct at91_gpio_bank at91sam9260_gpio[] 

__initdata = {
/* --------------------------------------------------------------------
* AT91SAM9260 processor initialization
* -------------------------------------------------------------------- */
-
static void __init at91sam9xe_map_io(void)
{
unsigned long sram_size;
@@ -351,6 +351,8 @@ static void __init at91sam9260_initialize(void)

/* Register GPIO subsystem */
at91_gpio_init(at91sam9260_gpio, 3);
+
+ at91_pm_set_standby(at91sam9_standby);
}

/* --------------------------------------------------------------------

(quoted diff) +0 -0

b/arch/arm/mach-at91/at91sam9261.c
index 0e07932..1edbb6f 100644

arch/arm/mach-at91/at91sam9261.c +3 -0
@@ -27,6 +27,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -293,6 +294,8 @@ static void __init at91sam9261_initialize(void)
 
  	/* Register GPIO subsystem */
  	at91_gpio_init(at91sam9261_gpio, 3);
+
+	at91_pm_set_sandby(at91sam9_standby);
  }
 
  /* --------------------------------------------------------------------
(quoted diff) +0 -0

b/arch/arm/mach-at91/at91sam9263.c
index 6ce7d18..b222d59 100644

arch/arm/mach-at91/at91sam9263.c +1 -0
@@ -26,6 +26,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -304,7 +305,6 @@ static struct at91_gpio_bank at91sam9263_gpio[] 

__initdata = {
/* --------------------------------------------------------------------
* AT91SAM9263 processor initialization
* -------------------------------------------------------------------- */
-
static void __init at91sam9263_map_io(void)
{
at91_init_sram(0, AT91SAM9263_SRAM0_BASE, AT91SAM9263_SRAM0_SIZE);
@@ -330,6 +330,8 @@ static void __init at91sam9263_initialize(void)

/* Register GPIO subsystem */
at91_gpio_init(at91sam9263_gpio, 5);
+
+ at91_pm_set_standby(at91sam9263_standby);
}

/* --------------------------------------------------------------------

(quoted diff) +0 -0

b/arch/arm/mach-at91/at91sam9g45.c
index 474ee04..4186f37 100644

arch/arm/mach-at91/at91sam9g45.c +1 -0
@@ -26,6 +26,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -355,7 +356,6 @@ static struct at91_gpio_bank at91sam9g45_gpio[] 

__initdata = {
/* --------------------------------------------------------------------
* AT91SAM9G45 processor initialization
* -------------------------------------------------------------------- */
-
static void __init at91sam9g45_map_io(void)
{
at91_init_sram(0, AT91SAM9G45_SRAM_BASE, AT91SAM9G45_SRAM_SIZE);
@@ -379,6 +379,8 @@ static void __init at91sam9g45_initialize(void)

/* Register GPIO subsystem */
at91_gpio_init(at91sam9g45_gpio, 5);
+
+ at91_pm_set_standby(at91sam9g45_standby);
}

/* --------------------------------------------------------------------

(quoted diff) +0 -0

b/arch/arm/mach-at91/at91sam9n12.c
index c7d670d..cc61e09 100644

arch/arm/mach-at91/at91sam9n12.c +7 -1
@@ -21,6 +21,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -217,13 +218,18 @@ static void __init at91sam9n12_register_clocks(void)
  /* --------------------------------------------------------------------
   *  AT91SAM9N12 processor initialization
   * -------------------------------------------------------------------- */
-
  static void __init at91sam9n12_map_io(void)
  {
  	at91_init_sram(0, AT91SAM9N12_SRAM_BASE, AT91SAM9N12_SRAM_SIZE);
  }
 
+static void __init at91sam9n12_initialize(void)
+{
+	at91_pm_set_standby(at91sam9_standby);
+}
+
  AT91_SOC_START(at91sam9n12)
  	.map_io = at91sam9n12_map_io,
  	.register_clocks = at91sam9n12_register_clocks,
+	.init = at91sam9n12_initialize,
  AT91_SOC_END
(quoted diff) +0 -0

b/arch/arm/mach-at91/at91sam9rl.c
index d4ec0d9..b0c8cb6 100644

arch/arm/mach-at91/at91sam9rl.c +1 -0
@@ -27,6 +27,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -261,7 +262,6 @@ static struct at91_gpio_bank at91sam9rl_gpio[] 

__initdata = {
/* --------------------------------------------------------------------
* AT91SAM9RL processor initialization
* -------------------------------------------------------------------- */
-
static void __init at91sam9rl_map_io(void)
{
unsigned long sram_size;
@@ -296,6 +296,8 @@ static void __init at91sam9rl_initialize(void)

/* Register GPIO subsystem */
at91_gpio_init(at91sam9rl_gpio, 4);
+
+ at91_pm_set_standby(at91sam9_standby);
}

/* --------------------------------------------------------------------

(quoted diff) +0 -0

b/arch/arm/mach-at91/at91sam9x5.c
index 916e5a1..9ef7bc6 100644

arch/arm/mach-at91/at91sam9x5.c +6 -1
@@ -21,6 +21,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -316,12 +317,15 @@ static void __init at91sam9x5_register_clocks(void)
  /* --------------------------------------------------------------------
   *  AT91SAM9x5 processor initialization
   * -------------------------------------------------------------------- */
-
  static void __init at91sam9x5_map_io(void)
  {
  	at91_init_sram(0, AT91SAM9X5_SRAM_BASE, AT91SAM9X5_SRAM_SIZE);
  }
 
+static void __init at91sam9x5_initialize(void)
+{
+	at91_pm_set_standby(at91sam9_standby);
+}
  /* --------------------------------------------------------------------
   *  Interrupt initialization
   * -------------------------------------------------------------------- */
@@ -329,4 +333,5 @@ static void __init at91sam9x5_map_io(void)
  AT91_SOC_START(at91sam9x5)
  	.map_io = at91sam9x5_map_io,
  	.register_clocks = at91sam9x5_register_clocks,
+	.init = at91sam9x5_initialize,
  AT91_SOC_END
arch/arm/mach-at91/pm.c +5 -0
index debdbf8..42b955c 100644
@@ -318,6 +318,11 @@ static struct platform_device at91_cpuidle_device = {
  	.name = "cpuidle-at91",
  };
 
+void at91_pm_set_standby(void (*at91_standby)(void))
+{
+	at91_cpuidle_device.dev.platform_data = at91_standby;	
+}
+
  static int __init at91_pm_init(void)
  {
  #ifdef CONFIG_AT91_SLOW_CLOCK
@@ -327,16 +332,8 @@ static int __init at91_pm_init(void)
  	pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow 

clock mode)" : ""));

/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */
- if (cpu_is_at91rm9200()) {
- at91_cpuidle_device.dev.platform_data = at91rm9200_standby;
+ if (cpu_is_at91rm9200())
at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
- } else if (cpu_is_at91sam9g45()) {
- at91_cpuidle_device.dev.platform_data = at91sam9g45_standby;
- } else if (cpu_is_at91sam9263()) {
- at91_cpuidle_device.dev.platform_data = at91sam9263_standby;
- } else {
- at91_cpuidle_device.dev.platform_data = at91sam9_standby;
- }

  	platform_device_register(&at91_cpuidle_device);
arch/arm/mach-at91/pm.h +4 -0
index 2f5908f..76dd1a7 100644
@@ -11,9 +11,13 @@
  #ifndef __ARCH_ARM_MACH_AT91_PM
  #define __ARCH_ARM_MACH_AT91_PM
 
+#include <asm/proc-fns.h>
+
  #include <mach/at91_ramc.h>
  #include <mach/at91rm9200_sdramc.h>
 
+extern void at91_pm_set_standby(void (*at91_standby)(void));
+
  /*
   * The AT91RM9200 goes into self-refresh mode with this command, and will
   * terminate self-refresh automatically on the next SDRAM access.
arch/arm/mach-at91/sama5d3.c +7 -1
index 4012797..9a53db6 100644
@@ -21,6 +21,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -365,13 +366,18 @@ static void __init sama5d3_register_clocks(void)
  /* --------------------------------------------------------------------
   *  AT91SAM9x5 processor initialization
   * -------------------------------------------------------------------- */
-
  static void __init sama5d3_map_io(void)
  {
  	at91_init_sram(0, SAMA5D3_SRAM_BASE, SAMA5D3_SRAM_SIZE);
  }
 
+static void __init sama5d3_initialize(void)
+{
+	at91_set_standby(at91sam9_standby);
+}
+
  AT91_SOC_START(sama5d3)
  	.map_io = sama5d3_map_io,
  	.register_clocks = sama5d3_register_clocks,
+	.init = sama5d3_initialize,
  AT91_SOC_END
Quoted 6 lines
Quoted 6 lines

<http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs

Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

Signature · 5 lines
  <http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
#10 lore raw

PATCH 1/2 ARM: at91: cpuidle: convert to platform driver

Quoted 54 lines · Daniel Lezcano
Quoted 10 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 9 lines · Daniel Lezcano
Quoted 8 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 7 lines · Daniel Lezcano

Use the platform driver model to separate the cpuidle specific code from the low level pm code. It allows to remove the dependency between these two components.

Tested-on usb-a9263 (at91sam9263)

[ ... ]

Quoted 16 lines
Quoted 16 lines
Quoted 16 lines

Review

Quoted 12 lines

---

(quoted diff) +8 -1
 	/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */
-	if (cpu_is_at91rm9200())
+	if (cpu_is_at91rm9200()) {
+		at91_cpuidle_device.dev.platform_data = at91rm9200_standby;
 		at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
+	} else if (cpu_is_at91sam9g45()) {
+		at91_cpuidle_device.dev.platform_data = at91sam9g45_standby;
+	} else if (cpu_is_at91sam9263()) {
+		at91_cpuidle_device.dev.platform_data = at91sam9263_standby;
+	} else {
+		at91_cpuidle_device.dev.platform_data = at91sam9_standby;

no this is too dangerous when adding new SoC

you must list the supported SoC

Quoted 8 lines
Quoted 5 lines
Quoted 1 line

and I prefer to move this code to the SoC init structure

Do you mean register the platform_device in eg. at91rm9200_initialize with the right platform data ?

yes as example

Best Regards,

Hi Jean-Christophe,

I did the changes but there are different drawbacks with the approach. The first one is the AT91_SOC_START is too early to call the platform_device_register. The second one is we have multiple declaration of the platform_device which is not really nice.

I found the following solution:

The platform_device is static in pm.c, there is a at91_pm_set_standby function. All AT91_SOC_START call at91_pm_set_standby with the right standby function callback, which in turns set the platform data for the cpuidle platform device. When the init call for pm is made, it registers the platform device.

Quoted 4 lines

That has the benefit to encapsulate the platform device and having it in a single place and also we have the information to remove the { if then else } statements we have in 'at91_pm_enter's case block for PM_SUSPEND_STANDBY.

why not

but some comment

and that was one of the reason why the else in the previous implementation was wrong

Quoted 158 lines

Does it sound ok for you ?

Thanks
-- Daniel

arch/arm/mach-at91/at91rm9200.c +3 -0
index 4aad93d..0d234f2 100644
@@ -27,6 +27,7 @@
 #include "generic.h"
 #include "clock.h"
 #include "sam9_smc.h"
+#include "pm.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -337,6 +338,8 @@ static void __init at91rm9200_initialize(void)
 	/* Initialize GPIO subsystem */
 	at91_gpio_init(at91rm9200_gpio,
 		cpu_is_at91rm9200_bga() ? AT91RM9200_BGA : AT91RM9200_PQFP);
+
+	at91_pm_set_standby(at91rm9200_standby);
 }
 
 
arch/arm/mach-at91/at91sam9260.c +1 -1
index 5de6074..9fd7aa6 100644
@@ -28,6 +28,7 @@
 #include "generic.h"
 #include "clock.h"
 #include "sam9_smc.h"
+#include "pm.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -307,7 +308,6 @@ static struct at91_gpio_bank at91sam9260_gpio[]
 __initdata = {
 /* --------------------------------------------------------------------
  *  AT91SAM9260 processor initialization
  * -------------------------------------------------------------------- */
-
 static void __init at91sam9xe_map_io(void)
 {
arch/arm/mach-at91/at91sam9260.c +2 -0
 	unsigned long sram_size;
@@ -351,6 +351,8 @@ static void __init at91sam9260_initialize(void)
 
 	/* Register GPIO subsystem */
 	at91_gpio_init(at91sam9260_gpio, 3);
+
+	at91_pm_set_standby(at91sam9_standby);
 }
 
 /* --------------------------------------------------------------------
arch/arm/mach-at91/at91sam9261.c +3 -0
index 0e07932..1edbb6f 100644
@@ -27,6 +27,7 @@
 #include "generic.h"
 #include "clock.h"
 #include "sam9_smc.h"
+#include "pm.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -293,6 +294,8 @@ static void __init at91sam9261_initialize(void)
 
 	/* Register GPIO subsystem */
 	at91_gpio_init(at91sam9261_gpio, 3);
+
+	at91_pm_set_sandby(at91sam9_standby);
 }
 
 /* --------------------------------------------------------------------
arch/arm/mach-at91/at91sam9263.c +1 -1
index 6ce7d18..b222d59 100644
@@ -26,6 +26,7 @@
 #include "generic.h"
 #include "clock.h"
 #include "sam9_smc.h"
+#include "pm.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -304,7 +305,6 @@ static struct at91_gpio_bank at91sam9263_gpio[]
 __initdata = {
 /* --------------------------------------------------------------------
  *  AT91SAM9263 processor initialization
  * -------------------------------------------------------------------- */
-
 static void __init at91sam9263_map_io(void)
 {
arch/arm/mach-at91/at91sam9263.c +2 -0
 	at91_init_sram(0, AT91SAM9263_SRAM0_BASE, AT91SAM9263_SRAM0_SIZE);
@@ -330,6 +330,8 @@ static void __init at91sam9263_initialize(void)
 
 	/* Register GPIO subsystem */
 	at91_gpio_init(at91sam9263_gpio, 5);
+
+	at91_pm_set_standby(at91sam9263_standby);
 }
 
 /* --------------------------------------------------------------------
arch/arm/mach-at91/at91sam9g45.c +1 -1
index 474ee04..4186f37 100644
@@ -26,6 +26,7 @@
 #include "generic.h"
 #include "clock.h"
 #include "sam9_smc.h"
+#include "pm.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -355,7 +356,6 @@ static struct at91_gpio_bank at91sam9g45_gpio[]
 __initdata = {
 /* --------------------------------------------------------------------
  *  AT91SAM9G45 processor initialization
  * -------------------------------------------------------------------- */
-
 static void __init at91sam9g45_map_io(void)
 {
arch/arm/mach-at91/at91sam9g45.c +2 -0
 	at91_init_sram(0, AT91SAM9G45_SRAM_BASE, AT91SAM9G45_SRAM_SIZE);
@@ -379,6 +379,8 @@ static void __init at91sam9g45_initialize(void)
 
 	/* Register GPIO subsystem */
 	at91_gpio_init(at91sam9g45_gpio, 5);
+
+	at91_pm_set_standby(at91sam9g45_standby);
 }
 
 /* --------------------------------------------------------------------
arch/arm/mach-at91/at91sam9n12.c +1 -0
index c7d670d..cc61e09 100644
@@ -21,6 +21,7 @@
 #include "generic.h"
 #include "clock.h"
 #include "sam9_smc.h"
+#include "pm.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -217,13 +218,18 @@ static void __init at91sam9n12_register_clocks(void)
 /* --------------------------------------------------------------------

arch/arm/mach-at91/at91sam9n12.c static void __init at91sam9n12_register_clocks(void) · line 227

Quoted 10 lines
arch/arm/mach-at91/at91sam9n12.c +2 -1
  *  AT91SAM9N12 processor initialization
  * -------------------------------------------------------------------- */
-
 static void __init at91sam9n12_map_io(void)
 {
 	at91_init_sram(0, AT91SAM9N12_SRAM_BASE, AT91SAM9N12_SRAM_SIZE);
 }
 
+static void __init at91sam9n12_initialize(void)
+{

this is wrong we use a ddr comtroller not the same as the sam9

Quoted 53 lines
arch/arm/mach-at91/at91sam9n12.c +4 -0
+	at91_pm_set_standby(at91sam9_standby);
+}
+
 AT91_SOC_START(at91sam9n12)
 	.map_io = at91sam9n12_map_io,
 	.register_clocks = at91sam9n12_register_clocks,
+	.init = at91sam9n12_initialize,
 AT91_SOC_END
arch/arm/mach-at91/at91sam9rl.c +1 -1
index d4ec0d9..b0c8cb6 100644
@@ -27,6 +27,7 @@
 #include "generic.h"
 #include "clock.h"
 #include "sam9_smc.h"
+#include "pm.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -261,7 +262,6 @@ static struct at91_gpio_bank at91sam9rl_gpio[]
 __initdata = {
 /* --------------------------------------------------------------------
  *  AT91SAM9RL processor initialization
  * -------------------------------------------------------------------- */
-
 static void __init at91sam9rl_map_io(void)
 {
arch/arm/mach-at91/at91sam9rl.c +2 -0
 	unsigned long sram_size;
@@ -296,6 +296,8 @@ static void __init at91sam9rl_initialize(void)
 
 	/* Register GPIO subsystem */
 	at91_gpio_init(at91sam9rl_gpio, 4);
+
+	at91_pm_set_standby(at91sam9_standby);
 }
 
 /* --------------------------------------------------------------------
arch/arm/mach-at91/at91sam9x5.c +1 -0
index 916e5a1..9ef7bc6 100644
@@ -21,6 +21,7 @@
 #include "generic.h"
 #include "clock.h"
 #include "sam9_smc.h"
+#include "pm.h"
 
 /* --------------------------------------------------------------------
  *  Clocks

arch/arm/mach-at91/at91sam9x5.c static void __init at91sam9x5_register_clocks(void) · line 319

Quoted 4 lines
arch/arm/mach-at91/at91sam9x5.c +0 -1
@@ -316,12 +317,15 @@ static void __init at91sam9x5_register_clocks(void)
 /* --------------------------------------------------------------------
  *  AT91SAM9x5 processor initialization
  * -------------------------------------------------------------------- */
-

??

arch/arm/mach-at91/at91sam9x5.c static void __init at91sam9x5_register_clocks(void) · line 326

Quoted 7 lines
arch/arm/mach-at91/at91sam9x5.c +2 -0
 static void __init at91sam9x5_map_io(void)
 {
 	at91_init_sram(0, AT91SAM9X5_SRAM_BASE, AT91SAM9X5_SRAM_SIZE);
 }
 
+static void __init at91sam9x5_initialize(void)
+{

this is wrong we use a ddr comtroller not the same as the sam9

Quoted 34 lines
arch/arm/mach-at91/at91sam9x5.c +3 -0
+	at91_pm_set_standby(at91sam9_standby);
+}
 /* --------------------------------------------------------------------
  *  Interrupt initialization
  * -------------------------------------------------------------------- */
@@ -329,4 +333,5 @@ static void __init at91sam9x5_map_io(void)
 AT91_SOC_START(at91sam9x5)
 	.map_io = at91sam9x5_map_io,
 	.register_clocks = at91sam9x5_register_clocks,
+	.init = at91sam9x5_initialize,
 AT91_SOC_END
arch/arm/mach-at91/pm.c +5 -2
index debdbf8..42b955c 100644
@@ -318,6 +318,11 @@ static struct platform_device at91_cpuidle_device = {
 	.name = "cpuidle-at91",
 };
 
+void at91_pm_set_standby(void (*at91_standby)(void))
+{
+	at91_cpuidle_device.dev.platform_data = at91_standby;	
+}
+
 static int __init at91_pm_init(void)
 {
 #ifdef CONFIG_AT91_SLOW_CLOCK
@@ -327,16 +332,8 @@ static int __init at91_pm_init(void)
 	pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow
 clock mode)" : ""));
 
 	/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */
-	if (cpu_is_at91rm9200()) {
-		at91_cpuidle_device.dev.platform_data = at91rm9200_standby;

arch/arm/mach-at91/pm.c static int __init at91_pm_init(void) · line 338

Quoted 10 lines
arch/arm/mach-at91/pm.c +1 -7
+	if (cpu_is_at91rm9200())
 		at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
-	} else if (cpu_is_at91sam9g45()) {
-		at91_cpuidle_device.dev.platform_data = at91sam9g45_standby;
-	} else if (cpu_is_at91sam9263()) {
-		at91_cpuidle_device.dev.platform_data = at91sam9263_standby;
-	} else {
-		at91_cpuidle_device.dev.platform_data = at91sam9_standby;
-	}
 

only register it if the call back is set

Quoted 34 lines
arch/arm/mach-at91/pm.c +0 -0
 	platform_device_register(&at91_cpuidle_device);
arch/arm/mach-at91/pm.h +4 -0
index 2f5908f..76dd1a7 100644
@@ -11,9 +11,13 @@
 #ifndef __ARCH_ARM_MACH_AT91_PM
 #define __ARCH_ARM_MACH_AT91_PM
 
+#include <asm/proc-fns.h>
+
 #include <mach/at91_ramc.h>
 #include <mach/at91rm9200_sdramc.h>
 
+extern void at91_pm_set_standby(void (*at91_standby)(void));
+
 /*
  * The AT91RM9200 goes into self-refresh mode with this command, and will
  * terminate self-refresh automatically on the next SDRAM access.
arch/arm/mach-at91/sama5d3.c +1 -0
index 4012797..9a53db6 100644
@@ -21,6 +21,7 @@
 #include "generic.h"
 #include "clock.h"
 #include "sam9_smc.h"
+#include "pm.h"
 
 /* --------------------------------------------------------------------
  *  Clocks
@@ -365,13 +366,18 @@ static void __init sama5d3_register_clocks(void)
 /* --------------------------------------------------------------------

arch/arm/mach-at91/sama5d3.c static void __init sama5d3_register_clocks(void) · line 375

Quoted 10 lines
arch/arm/mach-at91/sama5d3.c +2 -1
  *  AT91SAM9x5 processor initialization
  * -------------------------------------------------------------------- */
-
 static void __init sama5d3_map_io(void)
 {
 	at91_init_sram(0, SAMA5D3_SRAM_BASE, SAMA5D3_SRAM_SIZE);
 }
 
+static void __init sama5d3_initialize(void)
+{

this is wrong we use a ddr comtroller not the same as the sam9

arch/arm/mach-at91/sama5d3.c static void __init sama5d3_register_clocks(void) · line 383

Quoted 10 lines
arch/arm/mach-at91/sama5d3.c +4 -0
+	at91_set_standby(at91sam9_standby);
+}
+
 AT91_SOC_START(sama5d3)
 	.map_io = sama5d3_map_io,
 	.register_clocks = sama5d3_register_clocks,
+	.init = sama5d3_initialize,
 AT91_SOC_END

Best Regards,
J.

#11 lore raw

PATCH 1/2 ARM: at91: cpuidle: convert to platform driver

Quoted 59 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 54 lines · Daniel Lezcano
Quoted 10 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 9 lines · Daniel Lezcano
Quoted 8 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 7 lines · Daniel Lezcano

Use the platform driver model to separate the cpuidle specific code from the low level pm code. It allows to remove the dependency between these two components.

Tested-on usb-a9263 (at91sam9263)

[ ... ]

Quoted 16 lines
Quoted 16 lines
Quoted 16 lines

Review

Quoted 12 lines

---
/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */

(quoted diff) +8 -1
-	if (cpu_is_at91rm9200())
+	if (cpu_is_at91rm9200()) {
+		at91_cpuidle_device.dev.platform_data = at91rm9200_standby;
  		at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
+	} else if (cpu_is_at91sam9g45()) {
+		at91_cpuidle_device.dev.platform_data = at91sam9g45_standby;
+	} else if (cpu_is_at91sam9263()) {
+		at91_cpuidle_device.dev.platform_data = at91sam9263_standby;
+	} else {
+		at91_cpuidle_device.dev.platform_data = at91sam9_standby;

no this is too dangerous when adding new SoC

you must list the supported SoC

Quoted 8 lines
Quoted 5 lines
Quoted 1 line

and I prefer to move this code to the SoC init structure

Do you mean register the platform_device in eg. at91rm9200_initialize with the right platform data ?

yes as example

Best Regards,

Hi Jean-Christophe,

I did the changes but there are different drawbacks with the approach. The first one is the AT91_SOC_START is too early to call the platform_device_register. The second one is we have multiple declaration of the platform_device which is not really nice.

I found the following solution:

The platform_device is static in pm.c, there is a at91_pm_set_standby function. All AT91_SOC_START call at91_pm_set_standby with the right standby function callback, which in turns set the platform data for the cpuidle platform device. When the init call for pm is made, it registers the platform device.

Quoted 4 lines

That has the benefit to encapsulate the platform device and having it in a single place and also we have the information to remove the { if then else } statements we have in 'at91_pm_enter's case block for PM_SUSPEND_STANDBY.

Quoted 6 lines

why not

but some comment

and that was one of the reason why the else in the previous implementation was wrong

Ok, I see.

I will send a V2.

Thanks for the review !

-- Daniel

Quoted 340 lines
Quoted 158 lines

Does it sound ok for you ?

Thanks
-- Daniel

arch/arm/mach-at91/at91rm9200.c +3 -0
index 4aad93d..0d234f2 100644
@@ -27,6 +27,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -337,6 +338,8 @@ static void __init at91rm9200_initialize(void)
  	/* Initialize GPIO subsystem */
  	at91_gpio_init(at91rm9200_gpio,
  		cpu_is_at91rm9200_bga() ? AT91RM9200_BGA : AT91RM9200_PQFP);
+
+	at91_pm_set_standby(at91rm9200_standby);
  }
 
 
arch/arm/mach-at91/at91sam9260.c +1 -1
index 5de6074..9fd7aa6 100644
@@ -28,6 +28,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -307,7 +308,6 @@ static struct at91_gpio_bank at91sam9260_gpio[]
 __initdata = {
  /* --------------------------------------------------------------------
   *  AT91SAM9260 processor initialization
   * -------------------------------------------------------------------- */
-
  static void __init at91sam9xe_map_io(void)
  {

unsigned long sram_size;

arch/arm/mach-at91/at91sam9260.c +2 -0
@@ -351,6 +351,8 @@ static void __init at91sam9260_initialize(void)
 
  	/* Register GPIO subsystem */
  	at91_gpio_init(at91sam9260_gpio, 3);
+
+	at91_pm_set_standby(at91sam9_standby);
  }
 
  /* --------------------------------------------------------------------
arch/arm/mach-at91/at91sam9261.c +3 -0
index 0e07932..1edbb6f 100644
@@ -27,6 +27,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -293,6 +294,8 @@ static void __init at91sam9261_initialize(void)
 
  	/* Register GPIO subsystem */
  	at91_gpio_init(at91sam9261_gpio, 3);
+
+	at91_pm_set_sandby(at91sam9_standby);
  }
 
  /* --------------------------------------------------------------------
arch/arm/mach-at91/at91sam9263.c +1 -1
index 6ce7d18..b222d59 100644
@@ -26,6 +26,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -304,7 +305,6 @@ static struct at91_gpio_bank at91sam9263_gpio[]
 __initdata = {
  /* --------------------------------------------------------------------
   *  AT91SAM9263 processor initialization
   * -------------------------------------------------------------------- */
-
  static void __init at91sam9263_map_io(void)
  {
  	at91_init_sram(0, AT91SAM9263_SRAM0_BASE, AT91SAM9263_SRAM0_SIZE);
arch/arm/mach-at91/at91sam9263.c +2 -0
@@ -330,6 +330,8 @@ static void __init at91sam9263_initialize(void)
 
  	/* Register GPIO subsystem */
  	at91_gpio_init(at91sam9263_gpio, 5);
+
+	at91_pm_set_standby(at91sam9263_standby);
  }
 
  /* --------------------------------------------------------------------
arch/arm/mach-at91/at91sam9g45.c +1 -1
index 474ee04..4186f37 100644
@@ -26,6 +26,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -355,7 +356,6 @@ static struct at91_gpio_bank at91sam9g45_gpio[]
 __initdata = {
  /* --------------------------------------------------------------------
   *  AT91SAM9G45 processor initialization
   * -------------------------------------------------------------------- */
-
  static void __init at91sam9g45_map_io(void)
  {
  	at91_init_sram(0, AT91SAM9G45_SRAM_BASE, AT91SAM9G45_SRAM_SIZE);
arch/arm/mach-at91/at91sam9g45.c +2 -0
@@ -379,6 +379,8 @@ static void __init at91sam9g45_initialize(void)
 
  	/* Register GPIO subsystem */
  	at91_gpio_init(at91sam9g45_gpio, 5);
+
+	at91_pm_set_standby(at91sam9g45_standby);
  }
 
  /* --------------------------------------------------------------------
arch/arm/mach-at91/at91sam9n12.c +1 -0
index c7d670d..cc61e09 100644
@@ -21,6 +21,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -217,13 +218,18 @@ static void __init at91sam9n12_register_clocks(void)
  /* --------------------------------------------------------------------

arch/arm/mach-at91/at91sam9n12.c static void __init at91sam9n12_register_clocks(void) · line 227

Quoted 10 lines
arch/arm/mach-at91/at91sam9n12.c +2 -1
   *  AT91SAM9N12 processor initialization
   * -------------------------------------------------------------------- */
-
  static void __init at91sam9n12_map_io(void)
  {
  	at91_init_sram(0, AT91SAM9N12_SRAM_BASE, AT91SAM9N12_SRAM_SIZE);
  }
 
+static void __init at91sam9n12_initialize(void)
+{

this is wrong we use a ddr comtroller not the same as the sam9

Quoted 53 lines
arch/arm/mach-at91/at91sam9n12.c +4 -0
+	at91_pm_set_standby(at91sam9_standby);
+}
+
  AT91_SOC_START(at91sam9n12)
  	.map_io = at91sam9n12_map_io,
  	.register_clocks = at91sam9n12_register_clocks,
+	.init = at91sam9n12_initialize,
  AT91_SOC_END
arch/arm/mach-at91/at91sam9rl.c +1 -1
index d4ec0d9..b0c8cb6 100644
@@ -27,6 +27,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -261,7 +262,6 @@ static struct at91_gpio_bank at91sam9rl_gpio[]
 __initdata = {
  /* --------------------------------------------------------------------
   *  AT91SAM9RL processor initialization
   * -------------------------------------------------------------------- */
-
  static void __init at91sam9rl_map_io(void)
  {

unsigned long sram_size;

arch/arm/mach-at91/at91sam9rl.c +2 -0
@@ -296,6 +296,8 @@ static void __init at91sam9rl_initialize(void)
 
  	/* Register GPIO subsystem */
  	at91_gpio_init(at91sam9rl_gpio, 4);
+
+	at91_pm_set_standby(at91sam9_standby);
  }
 
  /* --------------------------------------------------------------------
arch/arm/mach-at91/at91sam9x5.c +1 -0
index 916e5a1..9ef7bc6 100644
@@ -21,6 +21,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks

arch/arm/mach-at91/at91sam9x5.c static void __init at91sam9x5_register_clocks(void) · line 319

Quoted 4 lines
arch/arm/mach-at91/at91sam9x5.c +0 -1
@@ -316,12 +317,15 @@ static void __init at91sam9x5_register_clocks(void)
  /* --------------------------------------------------------------------
   *  AT91SAM9x5 processor initialization
   * -------------------------------------------------------------------- */
-

??

arch/arm/mach-at91/at91sam9x5.c static void __init at91sam9x5_register_clocks(void) · line 326

Quoted 7 lines
arch/arm/mach-at91/at91sam9x5.c +2 -0
  static void __init at91sam9x5_map_io(void)
  {
  	at91_init_sram(0, AT91SAM9X5_SRAM_BASE, AT91SAM9X5_SRAM_SIZE);
  }
 
+static void __init at91sam9x5_initialize(void)
+{

this is wrong we use a ddr comtroller not the same as the sam9

Quoted 34 lines
arch/arm/mach-at91/at91sam9x5.c +3 -0
+	at91_pm_set_standby(at91sam9_standby);
+}
  /* --------------------------------------------------------------------
   *  Interrupt initialization
   * -------------------------------------------------------------------- */
@@ -329,4 +333,5 @@ static void __init at91sam9x5_map_io(void)
  AT91_SOC_START(at91sam9x5)
  	.map_io = at91sam9x5_map_io,
  	.register_clocks = at91sam9x5_register_clocks,
+	.init = at91sam9x5_initialize,
  AT91_SOC_END
arch/arm/mach-at91/pm.c +5 -2
index debdbf8..42b955c 100644
@@ -318,6 +318,11 @@ static struct platform_device at91_cpuidle_device = {
  	.name = "cpuidle-at91",
  };
 
+void at91_pm_set_standby(void (*at91_standby)(void))
+{
+	at91_cpuidle_device.dev.platform_data = at91_standby;	
+}
+
  static int __init at91_pm_init(void)
  {
  #ifdef CONFIG_AT91_SLOW_CLOCK
@@ -327,16 +332,8 @@ static int __init at91_pm_init(void)
  	pr_info("AT91: Power Management%s\n", (slow_clock ? " (with slow
 clock mode)" : ""));
 
  	/* AT91RM9200 SDRAM low-power mode cannot be used with self-refresh. */
-	if (cpu_is_at91rm9200()) {
-		at91_cpuidle_device.dev.platform_data = at91rm9200_standby;

arch/arm/mach-at91/pm.c static int __init at91_pm_init(void) · line 338

Quoted 10 lines
arch/arm/mach-at91/pm.c +1 -7
+	if (cpu_is_at91rm9200())
  		at91_ramc_write(0, AT91RM9200_SDRAMC_LPR, 0);
-	} else if (cpu_is_at91sam9g45()) {
-		at91_cpuidle_device.dev.platform_data = at91sam9g45_standby;
-	} else if (cpu_is_at91sam9263()) {
-		at91_cpuidle_device.dev.platform_data = at91sam9263_standby;
-	} else {
-		at91_cpuidle_device.dev.platform_data = at91sam9_standby;
-	}
 

only register it if the call back is set

Quoted 34 lines
arch/arm/mach-at91/pm.c +0 -0
  	platform_device_register(&at91_cpuidle_device);
arch/arm/mach-at91/pm.h +4 -0
index 2f5908f..76dd1a7 100644
@@ -11,9 +11,13 @@
  #ifndef __ARCH_ARM_MACH_AT91_PM
  #define __ARCH_ARM_MACH_AT91_PM
 
+#include <asm/proc-fns.h>
+
  #include <mach/at91_ramc.h>
  #include <mach/at91rm9200_sdramc.h>
 
+extern void at91_pm_set_standby(void (*at91_standby)(void));
+
  /*
   * The AT91RM9200 goes into self-refresh mode with this command, and will
   * terminate self-refresh automatically on the next SDRAM access.
arch/arm/mach-at91/sama5d3.c +1 -0
index 4012797..9a53db6 100644
@@ -21,6 +21,7 @@
  #include "generic.h"
  #include "clock.h"
  #include "sam9_smc.h"
+#include "pm.h"
 
  /* --------------------------------------------------------------------
   *  Clocks
@@ -365,13 +366,18 @@ static void __init sama5d3_register_clocks(void)
  /* --------------------------------------------------------------------

arch/arm/mach-at91/sama5d3.c static void __init sama5d3_register_clocks(void) · line 375

Quoted 10 lines
arch/arm/mach-at91/sama5d3.c +2 -1
   *  AT91SAM9x5 processor initialization
   * -------------------------------------------------------------------- */
-
  static void __init sama5d3_map_io(void)
  {
  	at91_init_sram(0, SAMA5D3_SRAM_BASE, SAMA5D3_SRAM_SIZE);
  }
 
+static void __init sama5d3_initialize(void)
+{

this is wrong we use a ddr comtroller not the same as the sam9

arch/arm/mach-at91/sama5d3.c static void __init sama5d3_register_clocks(void) · line 383

Quoted 10 lines
arch/arm/mach-at91/sama5d3.c +4 -0
+	at91_set_standby(at91sam9_standby);
+}
+
  AT91_SOC_START(sama5d3)
  	.map_io = sama5d3_map_io,
  	.register_clocks = sama5d3_register_clocks,
+	.init = sama5d3_initialize,
  AT91_SOC_END

Best Regards,
J.

Signature · 5 lines
  <http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog